Search Documents

By J S. J van Deventer

Geopolymerisation is a new technology that processes and transforms aluminosilicate minerals into mechanically strong and chemically stable products. In this investigation, minerals such as fly ash and kaolinite were used as the solid raw materials for geopolymerisation. Inorganic salts were added to the geopolymeric pastes to simulate ionic contamination during processing for building and construction applications. The resultant products were examined and characterised physically. It was found that the early strength development of geopolymeric pastes could be changed according to the nature as well as the extent of the contamination. At a small dosage, the effect of the contamination on the early geopolymeric system depended heavily on the nature of the artificial surfaces that were created in the geopolymeric solution through the addition of the chemical additives. For example, the samples containing MgCl2 and Mg(NO3)2 had shown the same yield stress developments due to the similar surfaces that were formed. The cations of these salts were expected to hydrolyse and form magnesium hydroxide precipitates immediately after the addition to the early geopolymeric systems. The calcium cations of CaCl2 also precipitated upon addition, but the nature of the surfaces of these hydroxides was quite different to those of the magnesium hydroxides and gave rise to different yield stress development. The samples that contained the insoluble salts (in water) demonstrated different yield stress development when compared to each other because of the different nature of the additive surfaces that were exposed to the geopolymeric solution. These results suggested that heterogeneous nucleation could be responsible for the change of the rheological behaviour upon inorganic salt addition. When the extent of the ionic contamination was large, the anions released from the insoluble salts (in water) changed the nature as well as the concentration of the geopolymeric solution and the setting processes were retarded. Oxides, in general, behaved very differently from other salts, indicating the uniqueness of the oxygen anions in a system rich in hydroxyl and silicate anions. The inorganic salt contamination in geopolymers did not show any significant signs of structural change according to the XRD diffractograms collected. The seven-day compressive strength was not lowered by the inorganic salt contamination and it could sometimes be beneficial to the product performance, for example, an increase of 20 MPa was induced by the addition of calcium oxide. Inorganic salts as chemical additives have demonstrated the potential to modify setting times of geopolymers without sacrificing much of the productsÆ strength and integrity.

Jan 1, 2000

Gravity gold recovery has been practiced for thousands of years, making it one of the oldest forms of mineral processing. Gold is 19 times heavier than water although the barren rock is generally only 2.7 times heavier. Any potential gold ore needs to be characterised to assess its amenability to a gravity recoverable gold (GRG) process based on well planned and executed test work. Scale up considerations need to be considered in designing a gravity circuit. The economic impact of a gravity circuit should be justified based on the installed cost and likely benefits. Maximising gravity gold recovery results in a faster cash flow, lower operating cost per ounce and higher overall gold recoveries compared to the several weeks required to recover gold adsorbed onto carbon. The advent of centrifugal concentrators such as the Knelson and Falcon, coupled with intensive leaching of concentrates (ILR), has revolutionised gravity gold circuit designs. Considerations associated with the sizing of the centrifugal machines and the percentage of the circulating load (bleed) that should be processed is discussed in this paper. The trends with gravity circuit layout, engineering, as well as optimum dumping cycles, are important areas which require close consideration. Key aspects of these are presented in this paper. There are a number of circuit configurations to be considered, including the integration of different gravity concentrators. Other gravity process design considerations such as fewer modules, the effect of equipment size and enhancement of process efficiency using preconcentration, together with factors that affect OPEX and CAPEX are addressed. Practical considerations of maintenance, security from theft, minimisation of risk and water balance considerations are discussed using different equipment and circuit configurations. The trend towards using gravity recovery in flotation plants is also reviewed. A number of examples are cited and good design aspects highlighted.

Aug 1, 2010

By D McClelland, R Whittering

Minerals and Metals Group (MMG) subsidiary Lane Xang Minerals Ltd operates a single site copper and gold mine near Sepon in Lao PDR. Gold production commenced in 2002 and first cathode copper production was in March 2006. Plant throughputs for gold and copper are currently 2.5 Mt/yr and 1.4 Mt/yr respectively; use of a second tailings dam has commenced accordingly. Although the increased catchment area creates opportunities for more storage to reduce demand on other water sources, especially during the dry season, it also creates greater requirements for water treatment capacity.The water balance for mining operations in a tropical monsoon environment with dry winters presents on going management challenges. A successful mining operation depends on a careful balance of water inputs and outputs. The challenge prior to every wet season is having enough storage capacity to absorb potential rainfall. Plant operation in the dry season benefits from water captured and stored from the wet season which reduces the dependence on river water. Release of excess water to the environment is necessary to cope with the overall positive water balance and depends on suitable and effective treatment of water in accordance with the environmental guidelines.Ausenco has recently built and commissioned a second water treatment plant at the Sepon Copper Plant to process tailings decant water.  The objective of the second Sepon water treatment facility is to increase the site water discharge capacity to maintain the water balance and reduce the dependence on river water.  Decant water treatment is required to precipitate the contained heavy metals prior to discharging to surrounding wetlands.  The main metal that needs to be removed from the site water to meet discharge water quality requirements is manganese, as heavy metals are already precipitated to required levels in neutralisation before the tailings are sent to the storage facilities. A site layout provision for removal of manganese to produce a saleable carbonate precipitate is incorporated in the polishing plant design (future installation).

Jan 1, 2009

By Rowena C. Duckworth

The Ocean Drilling Program (ODP) is the largest international geoscience project in the world, and the state-of-the-art drill ship, the JOIDES Resolution, is permanently at sea. Each year there are six scientific cruises (legs) which each last approximately two months. These legs are designed by geoscientists from the nineteen countries that subscribe to ODP. Australia and Canada presently share ODP membership under the banner of the AUSCAN Consortium. The benefits of Australia's involvement in ODP include internationalisation of Australian geoscience, advanced graduate training, and unique scientific investigations of the ocean floors in the Australasian region. In addition, visits to Australian ports by the ODP drill ship, the JOIDES Resolution, contribute up to $2 million per visit to the local economy. Amongst the many other aspects of ten years of scientific drilling, ODP has significantly contributed to our understanding of hydrothermal processes on the seafloor. To date, three hydrothermal sites have been drilled to date by the ODP, Snakepit (MAR), Middle Valley (Juan de Fuca Ridge) and TAG (MAR). Two more hydrothermal sites are scheduled for 1996.

Jan 1, 1995

By D J. Kilkenny, D A. O’Toole, P B. Hills, K L. Seah

An investigation was undertaken to critically analyse the use of fibre reinforced shotcrete (FRS) for a variety of applications in large diameter shafts. Those applications included the use of FRS with or without the addition of subsequent rock bolting in the temporary support cycle prior to the installation of a permanent lining, most likely cast in situ concrete or as the final lining medium.Numerous authors have considered the early re-entry and strength characteristics of FRS in recent years. The current study has investigated the practical application of the recommendations of many leading authors in an endeavour to establish practical and acceptable risk-assessed procedures for the use of FRS for rapid, safe, efficient and cost-effective shaft sinking.Shaft sinking is regarded as a specialist and potentially higher risk activity due to the confined work environment, exposure to ground conditions and a high degree of manual handling associated with getting materials to the sinking face. The use of robotically applied FRS as a primary lining in shaft sinking has significant safety advantages in reducing manual handing associated with mesh safety support and bolting, as well as reducing direct exposure to ground conditions.The study involved both field testing and a literature review. The study established an initial set of criteria for the use of FRS in the development of large diameter shafts and demonstrated a number of scenarios where the technique of robotically applied FRS provided significant safety and cycle time advantages. The opportunity for a fully sprayed single pass lining was also investigated as part of the project.CITATION:Hills, P B, O’Toole, D A, Kilkenny, D J and Seah, K L, 2014. Exploring the use of fibre reinforced shotcrete in large diameter shafts, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 295–306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By J Weir

Accurate sampling of slurry streams is extremely important for metallurgical accounting in mining operations, not only for measuring the ore grade from the mine, but also for measuring the recovery of mineral by the mineral processing plant. Accurate sampling is also required for intermediate streams in complex circuits for determining efficiencies of processing units within the plant. As the profitability of the minerals industry is squeezed more with time, greater emphasis is being placed on efficient use of the resource and accountability of the various sections of the mining operations. This has led to increased awareness and interest in obtaining statistically correct sampling across the operations. Accurate sampling is not only required for metallurgical accounting, but is also required for on-line analysis of the slurry streams for elemental analysis and for particle size. Sampling of slurry streams for metallurgical accounting purposes has traditionally been one of the areas of concern in mineral processing plants. In the first instance, the sampler must be designed to comply with the fundamental principles of sampling theory and must provide a representative sample of the slurry stream. In the second instance, the sampler must continue to reliably provide a representative sample, regardless of wear of the equipment or build up of solids with time and other operating issues. To-date the main type of sampler that has been used in mineral processing plants for metallurgical accounting has been the Cross-Cut sampler. These have a cutter that periodically cuts across the full slurry stream. For large flow slurry streams, these are often followed by a secondary and perhaps a tertiary sampler, to reduce the flow-rate or sample, to a manageable size. This paper discusses a new method of sampling slurry streams that has been developed by Thermo Gamma-Metrics, previously known as Amdel Instrumentation. The new samplers overcome many of the problems associated with cross-cut samplers while providing a sample which is representative of the main stream, throughout the life of the sampling system. The sampler is called the SamStat (Sampling Station) and it is now proven in many applications across many countries and mineral processing plants (PGMs, Cu/Au, Pb/Zn, etc).

Jan 1, 2002

By R P. Bewick

Many future and current block and panel caves extract ore from veined rock masses. These rock masses are composed of open joints forming blocks or rock with healed networks of veinlets. These two types of discontinuities pose a challenge for rock mass characterisation and classification due to difficulties in distinguishing actually open joints from healed but weak veins when diamond core drilling and excavation blasting practices disturb the rock mass. The inability of separating characteristics of open joints and healed veins has often resulted in an underestimation of the rock mass quality and as a consequence led to inappropriate assessments of rock mass response to mining (ie rock mass behaviour) and consequently deficient excavation stability assessments and ground support designs. In this paper, guidelines are provided to improve the characterisation and classification of veined rock masses. It is shown how veined rock masses can be mischaracterised resulting in often incorrect forecasting of rock mass behaviour. Following this, the classification of veined rock masses is examined. It is shown how the primary classification systems (ie Q – Barton, Lien and Lunde, 1974; rock mass rating (RMR) – Bieniawski, 1976) may not lead to reliable ratings in veined rock masses if care is not taken to differentiate between open joints and veins of varying strength. Examples are provided to illustrate how the Q and RMR systems are insensitive to veining. Finally, an example of characterising a veined rock mass for design purposes is presented.CITATION:Bewick, R P and Kaiser, P K, 2016. Characterisation and classification of veined rocks for rock mass behaviour assessment, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 825–834 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Bioleaching of Weathered Saprolite - Heavy Metal Adaptation Mechanisms of Aspergillus foetidus Nickel laterite ores remain important to the future supply of Ni and Co as they contain the bulk of known nickel and cobalt reserves (80 per cent and 90 - 95 per cent respectively). Current commercial extractions of Ni and Co from nickel laterite ores are energy intensive and operational costs are high. Microbial leaching of oxide ores has the potential to offer a much needed step-change in the technology for processing laterite ores. Biological leaching of low-grade nickel laterite is based on a non-traditional leaching of oxide minerals using heterotrophic micro-organisms. The organisms solubilise metals by excreting organic acids; these acids then form complexes with heavy metals. Optimisation of the process in in-situ application, however, has been hampered by the toxicity of the heavy metals that are being leached by the organisms. Our recent study has shown that organisms are able to develop tolerance towards heavy metals by adaptation. This study examined the extracellular metal detoxification mechanisms of A. foetidus in 0.2 per cent (wt/v) to 0.7 per cent (wt/v) of weathered saprolite ore. To support our analysis, FTIR, CHNS and microscopy were used to confirm the participation of specific functional groups in the extracellular detoxification process.

Sep 13, 2010

By D O’Dea, B Godel, T Honeyands, G Evans, T Harvey

The pores within iron ore sinter are important for producing a high quality material that is strong and easily reduced. The complementary methods of mercury intrusion porosimetry (MIP) and X-ray computed tomography (CT) were used to characterise the structure of industrial and pilot scales sinters across a wide range of pore sizes (3 nm to 100 µm for MIP and 50 µm to 5 mm for CT). The inhomogeneous nature of sinter and the variation in the measurements make it difficult to compare samples. The generalised additive modelling (GAM) approach, using the open source statistical software package, R, has been applied to highlight where there are peaks in the concentration of pore sizes. Importantly, the shape of the GAM-fitted function and the heights of the peaks show statistically significant differences between samples. For the samples investigated, the GAM-fitted functions for the MIP volume distribution of pore diameters were found to have a common set of distinctive peaks at 0.005, 0.6 and 20 µm. The GAM approach was also applied to the X-ray CT measured pore wall thickness, highlighting a single peak whose position varies between samples. The cause of these distinctive peaks and their implications for sinter quality are discussed. Correlation was found between the volume in peak 1 (0.005 µm) and the concentration of primary hematite. No correlation was found between the pore wall thickness and the strength of the sinter, suggesting the composition of the pore walls may be more important. Future work will focus on small-scale sinters produced under tightly controlled conditions to study sinters with a wider range of quality values.CITATION:Harvey, T, O’Dea, D, Evans, G, Godel, B and Honeyands, T, 2017. Highlighting key features of the pore structure of iron ore sinter using mercury intrusion porosimetry and X-ray computed tomography, in Proceedings Iron Ore 2017, pp 39–48 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The Ministry of Economic Development has as its slogan æTogether making the differenceÆ. The Ministry is required to work in partnership with the private sector, local authorities, Maori economic entities, trade unions and community groups to transform New Zealand's industrial and economic base. The Government is seeking to achieve sustainable and balanced economic development by: being more actively involved in economic management; working in partnership with the public and private sector and with worker and business interests; focusing on adding value in industries (including primary industries) with long term potential; and bringing the tools of economic policy together in a coordinated way. The Ministry, particularly through its operating group Crown Minerals, is committed to working with industry to achieve mutual goals and to obtain continuing investment in minerals and coal exploration and mining and an active New Zealand minerals industry.

Jan 1, 2000

The Coal Resources Survey commenced in 1974 as a search for Huntly Power Station coal, but soon developed into the most detailed regional coal search programme to be instituted in New Zealand. The program was initially conceived as geological in nature, but later included geotechnical, geohydrological, mining assessment, coal use, and environmental considerations in its investigations. The programme never undertook development work but has provided Government and the private sector with a sound basis for identifying development options. The discovery of large-scale coal resources in the Mokau, Waikato, and Taranaki regions and the lignite resources of Otago and Southland are a measure of the Survey's success. The directive by Government to phase out the NZCRS to a large extent coincides with the completion stage of the program. With most of the detailed regional study finished, it now remains to collate the data and publish summary reports at Coalfield and Coal Region level, in order to maximise the use and value of the data collected over the years.

Jan 1, 1987

By S Henderson, J V. Lawless

The worldwide association of low-sulfidation epithermal gold mineralisation, bimodal rhyolitic-basaltic volcanism and rifting is confirmed in New Zealand. In the currently productive Coromandel epithermal-gold province reported Ar-Ar dating of adularia from low sulfidation deposits falls into two groups at 6 and 7 Ma. Bimodal rhyolitic-basaltic volcanism has been reported to be K-Ar dated at 9 to 7 Ma and 6 to 5.5 Ma. Epithermal gold mineralisation in Northland is spatially associated with bimodal basaltic-rhyolitic volcanism, with rifting cogenetic with that in the CVZ. The Taupo Volcanic zone (TVZ) is sufficiently young that the presence of a segmented rift with recent bimodal rhyolitic-basaltic volcanism can be genetically associated with epithermal gold mineralisation, which occurs as both fossil occurrences and in active geothermal fields. This reinforces the known potential prospectiveness of the Coromandel area and increases that of Northland and the Taupo Volcanic Zone.

Jan 1, 2005

Effects of Hydrated Mg2+ on KCl Flotation

Sep 13, 2010

By D Craw, N Newman

Previously published stream quality data and AMD (acid mine drainage) analyses have been collated into a database (DAME û Database for Assessment of Mine Environments) and additional samples including NMD (neutral mine drainage) have been collected from coal mine drainages on the West Coast. Variations in the chemistry of mine drainage samples can be related to four factors: 1.       regional geology (Brunner Coal Measures or Paparoa Coal Measures) 2.       mine type (open cast or underground) 3.       hydrogeology 4.       local geology   In general mines hosted in Paparoa Coal Measures produce NMD whereas mines hosted in Brunner Coal Measures produce AMD with highly variable chemistry. Differences in coal mine drainage chemistry between mines hosted in Brunner and Paparoa Coal Measure sequences can be measured with acid-base accounting geochemistry. Correlation of ANC (acid neutralising capacity) and MPA (maximum potential acidity) analysis of rocks with mine drainage samples is substantially better than correlation of NAG (net acid generation) analysis with mine drainage chemistry.   It is likely that NAG analysis over estimates acid generation potential of some samples due to release of organic acids that are not released under environmental conditions. In general, differences in mine drainage chemistry between Brunner and Paparoa hosted mines are attributed to the effect depositional environment and diagenesis on coal measure composition. Exceptions to generalisations relating mine drainage to Paparoa or Brunner host rocks are likely where local geological conditions cause increased deposition of pyrite in Paparoa rocks and additional analyses are required to confirm interpretations.   Based on the interpretation of these results a mine drainage chemistry hazard model has been constructed. The hazard model predicts likely variations in mine drainage chemistry based on the four factors listed above. The hazard model has implications for mine related water quality risks. For example, ecotoxicity, human health affects and selection of remediation techniques are all sensitive to mine drainage chemistry.

Jan 1, 2006

By V M. Silva, P A. A Martins, V O. Matthew, A L. S Fonseca, E B. Cunha, A J. D Ferrari, E M. S Silva, A C. Silva, D R. T Vilela

The Anglo American phosphate mine is located in the Brazilian state of Goiás and possesses one of Brazil’s most important phosphate rock deposits, with the site being the country’s second largest producer of phosphate rock concentrate. Despite the site having been in operation since 1979, the mining team only started using explosives in 2004 when rocks with greater hardness started to appear in the mine’s geological profile. Rock excavation was previously performed mechanically. Until 2013, only rocks with high hardness were blasted, this following the standard drilling grid that was defined in 2004 without any changes in the blast parameters. The aim of this paper is to show how fragmentation optimisation has yielded positive results at all stages of the production chain, from the mine to the mill passing through an impact hammer crusher, a rod mill and ball mill, operating in close circuit with hydrocyclones.While incorporating the mine to mill holistic approach during the operational integration, the focus was on defining the blasting domains and respective optimal fragmentation and measuring the benefits of blasting in terms of reduction in energy and grinding media consumed in the comminution processes. In the first stage, the blasting team made changes to the blasting parameters and assessed the effects of these changes on fragmentation using computer software and on-site measurements. This generated a database that made it possible to divide the mine into blasting domains. For the second stage, teams from the plant, geology, mine planning and operation departments jointly made comparisons between the performance when processing stockpiles, which only included high hardness blasted ore (20–30 per cent of blasted ore). Changing the drilling grid’s size from 3.0 m × 3.8 m to 2.0 m × 2.6 m for high hardness rock with the presence of silicates resulted in a 40 per cent reduction in the P80 for the blasted material (from 459 to 278 mm), while changing the grid from 3.0 m × 3.8 m to 2.6 m × 3.2 m for high hardness rock without the presence of silicates generated a reduction of 25 per cent (from 270 to 204 mm). There were gains observed from the measurements at the mineral processing plant in terms of specific energy spent on comminution and on the consumption of grinding bodies in the rod mill. There was a measured reduction of circulating load during secondary grinding and a reduction in slime generation.CITATION:Silva, A C, Martins, P A A, Silva, E M S, Fonseca, A L S, Ferrari, A J D, Cunha, E B, Silva, V M, Matthew, V O and Vilela, D R T, 2015. Fragmentation optimisation – adopting mine to mill for reducing costs and increasing productivity, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 363–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By A Deakin

It has been almost a decade since the release of the International Council of Mining and Metals (ICMM) Health and Safety Critical Control Management: Good Practice Guide (2015a). During this time the ICMM member companies, along with many others across industry, have been busy designing, deploying and enhancing their own critical control management (CCM) programs. So, what have we learnt? This paper discusses the scope, application and learnings from the implementation of CCM within the mining industry. What’s going well? What are the common challenges? What are the opportunities to strengthen the approach? What are the threats to successful implementation? The paper draws on the author’s experience as one of the key contributors to the development of the CCM Good Practice Guide and an adviser to many mining companies, including six of the ICMM members. The paper focuses on the practical (operational) application of CCM and the cycle of identifying, defining, implementing, verifying and improving critical controls at the frontline. The paper also includes a discussion on the safety performance of the ICMM member companies over the past decade and provides a recommendation for how CCM can be incorporated into a more proactive model to measure safety performance. The paper concludes with practical recommendations that mining companies, regardless of their CCM maturity, can consider as they look ahead. They are supplemented by three additional recommendations for consideration at the industry level.

Apr 16, 2024

The early development patterns of both Australia and New Zealand were substantially in parallel and both were heavily indebted to gold mining for, providing the stimulus to growth. However, since the mining boom, of 1895 - 1899, the mining sector in New Zealand has progressively declined, while in Australia it has assumed an increasing importance in the economy. The continued dominance of minerals in Australian trade, and the fact that eight out of the top ten companies in Australia are directly involved in mineral exploration and production, has strongly influenced government and public attitude's to the minerals sector. Although the legal framework of mining and exploration Acts and Regulations are similar it is in, the method of administration, particularly in regard to exploration and prospecting licences, that the gulf across, the Tasman is apparent. Despite the relative ease of application and granting of licences in Australia, in the more settled south eastern part of the continent we are finding more and more land is being zoned unavailable for exploration. In the remote areas, the Aboriginals now control nearly ten per cent of the land area of Australia, virtually with drawing that portion from exploration. The concept of 'Australianisation' has softened a hardening attitude against foreign investment in mining on the part of the bureaucracy. This anti-mining attitude is fortunately, not shared by the public, and we can but hope that the will of the Australian people can filter through to our masters in Canberra, and ease the rapid increase in the number of regulatory bodies which does so much to inhibit the normal conduct of business. The delays caused by interminable hearings and committee investigations all cost money. This cost can only rebound back on the end consumer, who after all is a voter.

Jan 1, 1982

Many sampling standards arrive at a value for the prescribed sample mass by assuming a specific relation between the sample mass and the relative standard deviation of the fundamental error and assigning a value to the tolerated coefficient of variation. In order to obtain an equation that provides a relation between the minimum sample mass and the particle properties, many different models for the drawing of a sample have been developed. Here, a model for the drawing of a sample is proposed which can be considered to be a generalisation of the model used in GyÆs sampling theory. Using simulations, it is illustrated that the generalised model can lead to a better correspondence with actual sampling processes.

Jan 1, 2005

By E Christodoulou, L Zoumpoulakis

The kinetics of the thermal decomposition of MgCO3 was investigated using isothermal experiments performed in a thermogravimetric analyzer under a nitrogen atmosphere at 380¦, 400¦, 450¦ and 480¦C. The weight loss data as a function of time were modified to give the fraction that reacted (ß) and the rate of reaction (dß/dt) vs. time (t). Kinetic analysis of the experimental results, using three different methods, showed that diffusion predominates the MgCO3 decomposition over the investigated temperature range, with the data being best fitted by JanderÆs equation ([1−(1−ß)1/3]2=kt). The activation energy was estimated by Arrhenius plots using both the initial reaction rates and rate constants from fitting the above equation. The values estimated were 27.1 and 171.4 kJ/mol respectively.

Jan 1, 2001

By A S. Derrington

There are several long-standing rules of thumb that are often quoted in mine ventilation studies. They include airway ‘carrying velocities’ and the critical upcast air velocity range that must be avoided to prevent a water blanket forming. Quoting these rules of thumb may lend an air of legitimacy to a ventilation design, and allow the design engineer to avoid having to study a problem from first principles. But how valid are these shortcuts in today’s rapidly changing world? This paper summarises research into the genesis of several commonly quoted rules of thumb. It finds that they were very specific to the local conditions, practices and economics at the time they were developed. It also presents examples where applying these rules of thumb outside of their original context can lead to unexpected and erroneous results.CITATION:Derrington, A S, 2017. Ventilation rules of thumb – friend or foe? Focusing on design upcast air velocities for shafts and raise bores, in Proceedings Australian Mine Vent Conference 2017, pp 253–260 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017