Search Documents

By Ralph Hultgren, David W. Mitchell

MAGNESIUM alloys usually are superheated before casting in order to ensure fineness of grain. Superheat temperatures in common use range from 1600° to 1700°F while the casting temperature, which depends upon the mold shape, is usually 200° to 300°F lower. The process of superheating requires considerable time and seriously shortens the life of the iron pots used. Recently it has been reported' that if acetylene, carbon dioxide or natural gas is bubbled through molten electrolytic A.S.T.M. No. 4 alloy at 1400°F. for 5 min., grain refinement equivalent to that of superheating will take place. Addition of certain solids such as graphite or aluminum carbide accomplishes the same results.2 As will be shown in this paper, it is possible to achieve grain refinement in magnesium casting alloys at low temperatures by mechanical stirring of the molten metal for a short time. This process was developed in the course of research work, supervised by the War Metallurgy Committee under the "Restricted" Project NRC-550, for the Office of Production Research and Development of the War Production Board. This paper, based on that work, has been released for publication by the O.P.R.D. MATERIALS AND METHODS The alloys studied were the most common American sand-casting alloys designated as No. 4 and No. 17 by the American Society for Testing Materials. The magnesium used in these alloys was of both carbothermic3 and electrolytic4 origin. Chemical analyses supplied by the producers are shown in Table I. Each heat consisted of approximately 5 lb. of alloy melted in a Tercod crucible. It was refined by fluxing with Permanente No. 7* refining flux at 1300° to 1350°F. After cooling to 1200' to 1250°F., portions of approximately one pound each were ladled into iron crucibles contained in an electric furnace at about 1250°F. The molten metal was covered with Permanente No. 21† covering flux and then heated to the temperature to be investigated. Normally each of the four portions was given a different treatment. In a typical case one portion was stirred vigorously for 5 min., acetylene gas was passed through a second portion for 5 min., a third portion was superheated to 1600°F for 15 min., then cooled to casting temperature, and the fourth was held for 5 min. at the temperature of stirring or gassing without other treatment. Each portion was then cast into one-inch diameter cylinders in three "nonturbulent" molds of identical shape. One mold was made of cast iron and the other two of baked sand. The cast-iron mold and one of the baked sand molds were heated to 360°F., the other baked sand mold was at room temperature. The freezing times in these molds were

Jan 1, 1945

By Ralph Hultgren, David W. Mitchell

Magnesium alloys usually are superheated before casting in order to ensure fineness of grain. Superheat temperatures in common use range from 1600" to r 7o0°F.; the casting temperature, which depends upon the mold shape, is usually 200° to 300°F. lower. The process of superhcating requires considerable time and seriously shortens the life of the iron pots used. Recently it has been reported1 that if acetylene, carbon dioxide or natural gas is bubbled through molten electrolytic A.S.T.M. No. 4 alloy at 1400°F. for 5 min., grain refinement equivalent to that of superheating will take place. Addition of certain solids such as graphite or aluminum carbide accomplishes the same results? As will be shown in this paper, it is possible to achieve grain refinement in magnesium casting alloys at low temperatures by mechanical stirring of the molten metal for a short time. This process was developed in the course of research work, supervised by the War Metallurgy Committee under the "Restricted' project NRC-550, for the Office of Production Research and Development of the War Production Board. This paper, based on that work, has been released for publication by the O.P.R.D. Materials and Methods The alloys studied were the most common American sand-casting alloys designated as No. 4 and No. 17 by the American Society for Testing Materials. The magnesiun used in these alloys was of both carbothermic3 and electrolytic' origin. Chemical analyses supplied by the producers are shown in Table I. Each heat consisted of approximately 5 lb. of alloy melted in a Tercod crucible. It was refined by fluxing with Permanente No. 7* refining flux at 1300° to 1350°F. After cooling to 1200° to 1250°F., portions of approximately one pound each, were ladled into iron crucibles contained in an electric furnace at about 1250°F. The molten metal was covered with Permanente No. 21 † covering flux and then heated to the temperature to be investigated. Normally each of the four portions was given a different treatment. In a typical case one portion was stirred vigorously for 5 min., acetylene gas was passed through a second portion for 5 min., a third portion was superheated to 1600°F. for 15 min., then . cooled to casting temperature, and the fourth was held for 5 min. at the temperature of stirring or gassing without other treatment. Each portion was then cast into one-inch diameter cylinders in three "nonturbulent" molds of identical shape. One mold was made of cast iron and the other two of baked sand. The cast-iron mold and one of the baked sand molds were heated to 360°F., the other baked sand mold was at room temperature. The freezing times in these molds were

Jan 1, 1945

Paralleling recent experiments in the U. S., the Mines Branch of the Department of Mines and Technical Surveys in Ottawa has developed a laboratory process for recovering cell-grade alumina from aluminiferous shale. Mines Branch Research Report R45 (1959) entitled The Alum-Amine Process For The Recovery of Alumina From Shale by G. Thomas and T. R. Ingraham states " . . . With the recent resurgence in Canada, and in the United States, of attempts to recover cell-grade alumina from clays and shales, the Mines Branch undertook to review certain processes that had been tried with marginal success . . . In particular, it seemed quite possible that some recent developments in organic chemistry, relating to uranium technology, might be utilized for the removal of the last traces of iron from intermediate products to permit the attainment of a satisfactory grade of alumina." This introductory paragraph explains the authors' approach toward development of an alumina recovery process from shale. The following is an abstract of their successful laboratory experiments.

Jan 3, 1960

By R. E. Hobart

The development of the Hauto power plant and the claims made by various engineers that electricity was more economical than steam for power purposes in and about the mines, led the Lehigh Coal and Navigation Co., in 1911, to conduct a test to ascertain the consumption of power used by a large steam hoisting engine. The question being one on which no reliable information could be found, and the opinion of various engineers differing to such an extent, it was decided that a test under actual operating conditions was necessary. This was arranged for at one of the collieries. The engine selected was 2 30 by 60-in. (76.2 by 152.4-cm.) piston-valve engine of modern type, and comparatively new. The boiler plant from which the hoist received its power was about 600 ft. (182 m.) from the engine, the latter being fed by a 10-in. (25.4-cm.) steam line insulated with magnesia pipe covering. Two batteries of the boiler plant, aggregating 1200 hp., were cut off and fed into a separate steam line leading direct to the hoist engine. Steam auxiliaries, consisting of feed-water pump and blowers, were fed by the boilers in test, and their consumption charged against the hoist. A barrel weighing device was installed, as it was felt that this would be the most accurate way of determining the consumption of water. The fuel, No. 3 buckwheat, was carefully weighed, and every precaution was taken to make the test accurate in every particular. The test was run for 1 week, or a total of 168 hr. A record was kept of the number of trips hoisted or lowered, and continuous indicator cards were taken. One particular set of cards was taken with the hoist operating balanced, and also with the hoist operating with no counterweight other than the empty cage, the coal in the car being weighed. The speed of the hoist was taken by means of a graphic recording instrument which registered the number of revolutions every 5 sec. From this record, speed-time curves were plotted.

Jan 1, 1918

By John D. Ridge, Betty S. Moriwaki

The significant chromite producers listed in Table I11 are not major steel producers, with the exception of the USSR. After manganese, chromium is the most important alloying metal in steel. It would not be surprising to find a direct relationship between steel production and chromite imports. The precise connection is concealed by the other uses of chromite and the grades of steel produced by the various countries involved. In addition, the amount of ferrochromium made for export must figure in any calculation. Norway, a producer of considerable amounts of ferromanganese, imports significant quantities of chromite for ferrochromium manufacture. Most of the ferrochromium is exported to European steel- producing nations. Sweden imports only half as much chromite as Norway but makes far more chromium-bearing steel. Thus Sweden has far less ferro-chromium for export, although it supplies about 2000 tons per year to the U.S. and probably some- what more to such chromite-poor steel producers as Germany and Belgium-Luxemburg.

Jun 1, 1955

By George W. Doffing

Numerous contradictory statements have been made in the past regarding the importance of the seasonal influence of demand for motor fuel on prices of oil securities. It has often been said that the time to buy oil securities is in the spring, or just prior to the heavy consuming season for gasoline. The fallacy of this argument is brought out in the following paragraphs. Seasonality of Oil-security Prices The indexes used in this paper as indicators of prices of oil securities and general industrials are those compiled by Standard Statistics Co. The oil producing and refining stock index includes 14 representative petroleum companies, while the all-industrials index is made up of 347 issues. All figures are stated as relatives, with 1926 = 100. The primary basis of the index, and one that gives a good weighting of the relative importance of the company within the industry, is the total market value of the stock issue outstanding; i.e., the market price times the number of shares outstanding. Adjustments are made for the addition or elimination of issues from the group index, for stock dividends, split-ups, stock rights, et cetera. At the present time the oil producing and refining index includes the following companies: Atlantic Refining Co., Consolidated Oil Corporation, Continental Oil Co., Gulf Oil Corporation, Humble Oil & Refining Co., Ohio Oil Co., Royal Dutch Co., Shell Union Oil Corporation, Socony-Vacuum Oil Co., Standard Oil Company of California, Standard Oil Co. (Indiana), Standard Oil Co. (New Jersey), Texas Corporation, Union Oil Company of California. In calculating the seasonal for oil-security prices several periods have been selected as indicat,ive of major changes in the industry, as follows: 1. 1918 through 1936. This gives an over-all picture of the industry during the motor-vehicle, motor-fuel era. 2. 1927 through 1936. This period includes the control stages, both voluntary and coercive. 3. 1927 to September, 1933. This is the pre-code period of control.

Jan 1, 1937

By A. L. Field, P. H. Royster

The first report on the slag viscosity work of the Bureau of Mines was made by one of the authors1 in 1916. It was concerned chiefly with the method of measurement. A paper2 on this phase of the work was presented to the Institute in February, 1917, and a similar paper3 was communicated to the Faraday Society. PuRpose and Scope of the Slag Viscosity Tables Following the development of a suitable method, the next step in the investigation was the measurement of slag viscosity over a wide range of temperature and composition, and the arrangement of this experimental data in the form of tables for the use of the blast-furnace operator. It is believed that this information, if used intelligently, should help the operator to reduce losses in production caused by off-grade pig iron, to improve fuel economy, to promote operating efficiency, and to extend present-day practice to meet the increasing need of smelting lean and complex ores. In the experimental part of the work it was carly, observed that the temperature-viscosity relations of a slag were determined, for practical purposes, by the relative proportions of the three major constituents, lime (CaO), alumina (Al2O3), and silica (SiO2), provided the percentage

Jan 1, 1918

By K. Huessener

Discussion of the paper of K. HUESSENER, presented at the New York. meeting, February, .1916, and printed in Bulletin No. -110, February, 1916, pp. 443 to 474. KARL NIBECKER, Youngstown, O.-It has been contended that the method of measuring the operation of a blast-furnace boiler plant by means of the amount of steam generated per pound of coke used in the blast furnace is not of any value and even that it is quite misleading. It has been found, in the plant with which I am connected, that, in general, a blast furnace will operate during a month so close to average. conditions that the average monthly measure of the plant efficiency is indicated by the number of pounds of steam made per pound of coke put into the furnace, neglecting the amount of iron made and the amount of gas used for heating the stoves. For some time, it has been our custom to keep a record of this figure and use it as a general indicator of the operating practice. In comparing this figure from two different plants we have found some difficulty, due to differing conditions. It is conceivable but not altogether probable that a slight difference in burden, kind of ore or coke, would account for this difference. The method of using the gas, whether washed or unwashed, and the plant arrangement, may affect this number. For several plants on which we have worked up this number, we have found that most of the ordinary running irregularities are eliminated during a run of a month or more and that the number is, therefore, satisfactory. In connection with a plot of the number of pounds of steam generated per pound of coke, we are also plotting the production of the furnaces and the pounds of coke used per ton of production. With these three curves plotted on the same sheet, we believe that the operating man has sufficient information to judge of the efficiency of his plant' for any month.

Jan 5, 1916

THE decision of the lower court (United States District Court for the Southern District of New York) in the suit of the Dwight & Lloyd Sintering Co., vs. John E. Greenawalt has been affirmed by the United States Circuit Court of Appeals for the Second Circuit. In the original suit, infringement of seven patents was alleged, these covering the process of producing a sinter .out of finely pulverized metalliferous ores as practised in shallow pans operating intermittently in distinction to the Dwight 6: Lloyd continuous machine. The court found that the long delay in bringing suit precluded any recovery of profits from the defendant under the basic down-draft sintering patent, although Dwight & Lloyd are recognized as the inventors of this' contribution to the art and its .importance is acknowledged.

Jan 1, 1928

By L. R. Raymond, G. G. Binder

One primary purpose of hydraulic fracturing as a well stimulation technique is to overcome formation damage. The literature provides ways of designing fracture treatments and evaluating their results but not of incorporating formation damage in vertically fractured wells. Results of an investigation of this problem are presented in this paper. Prediction of stimulation ratios in vertically fractured, damaged wells is accomplished with a mathematical model relating stimulation ratio to relative conductivity of fractures whose lengths are not more than about half the drainage radius of the well. Comparison of results from the new model to results in published predictions verify its utility; these results also show that the range of stimulation ratios that can be predicted for undamaged wells is extended to include relative conductivities of less than 300. This extension is important when using fracturing to stimulate wells with high production rates and high native formation permeabilities. For example, large increases in daily oil production rate can be obtained with stimulation ratio increases as low as 1.25. The importance of complete fracture fill-up (uniform proppant packing) is shown through use of the mathematical model. If, at the mouth of a fracture, only a small fraction (1/2 percent) of the total fracture length is not packed with proppant, nearly all the polential stimulation increase is lost. Proppant crushing, compaction and embedment have been shown in laboratory studies to be responsible for low fracture conductivities in wells producing from highly stressed formations. Equipment and methods for testing the effect of stress (overburden) on conductivity of fructures in consolidated and unconsolidated sands are discussed in this paper. Laboratory tests with simlilated fractures in cores from both types of formations showed that crushing, compaction and embedment seriously affect conductivity. Results indicate that similar laboratory tests should be made when accurate knowledge of fracture conductivity is needed to assure good stimulation results for important wells. The chief factor in stimulation ratio reduction was found to be overburden pressure, but the size and type of proppant and the hardness of the formation have significant effects. Fracture conductivity reductions of up to 50 percent were observed with sand propping fractures in consolidated cores; a reduction of 83 percent was measured for an unconsolidated core. The range of effective overburden pressures for which conductivities were measured was from 100 to 5,000 psi. An example fracture design and evaluation problem indicates the usefulness of considering formation damage in planning well stimulation jobs. When damage exists, but its extent and the degree of permeability reduction are not estimated from diagnostic tests, the formation permeability used in planning the job may lead to under-designing. As the example shows, too low a target stimulation ratio can lead to much lower production rates (by half) than could be attained otherwise. Solutions of equations representing several special cases of the mathematical model are presented in graphical form and details of the derivations of the equations are given in the Appendix. INTRODUCTION Since its inception in 1947, hydraulic fracturing has proven to be an effective and widely accepted stimulation technique. In the past 18 years the ability to execute a successful hydraulic fracturing treatment has been substantially increased. The development of design and evaluation procedures1,2 has been one of the major contributions to this increased skill. However, as the art of hydraulic fracturing has moved closer to a science, new problems concerning the design and evaluation of the optimal hydraulic fracturing treatment have arisen. Three questions are pertinent to these problems. I. How is a fracturing job evaluated in a damaged well? 2. What is the effect on the stimulation ratio of not filling the fracture in the vicinity of the wellbore? 3. What is the effect of overburden pressure on fracture conductivity and, consequently, the stimulation ratio? A primary objective of fracturing a well is to stimulate production by overcoming wellbore damage. Presently. however, there is no rational basis for designing or evaluating the optimal fracturing treatment in a damaged well. All present fracture design and evaluation techniques assume that proppants can be uniformly placed in fractures. This assumption may be in serious error, particularly for the portion of a fracture directly adjacent to the wellbore. In this area, turbulence of the injected fluid can cause the proppant to be swept farther into the fracture. Also, loss of fluid from the fracture to the

By Raymond S. Weimer

Of the several characteristics of a coal that influence its suitability for use in a given piece of burning equipment, the clinkering and slagging characteristics of the ash of the coal are highly important. They determine the maximum rate at which the coal may be burned on a stoker or in pulverized form without difficulty from damage to metal parts, from erosion of refractory walls, or from stoppage of gas passages by accumulation on the tubes. They also determine the minimum rate at which a slag-tap furnace may be operated without difficulty in removal of the ash in fluid form. Need for a Better Criterion In common with other producers and users of coal, the Northern Illinois Coal Corporation has long used the available methods for the measurement of the clinkering characteristics of coal ash, chemical composition and fusion temperature of the ash, as criteria for the selection of coal that would suit the particular requirements of its customers. These two available criteria have greatly helped in the problem of selection but it is unnecessary to dwell upon the fact that they are not completely adequate for the purpose. The composition of the ash and its clinkering tendency vary widely over the company's mining area. In a certain period, some years ago, an unusual amount of severe clinkering of the ash of coal shipped made extremely acute the need for a better criterion of the clinkering that might be expected. It was also desirable that the criterion result from a reasonably rapid method, so that the clinkering characteristics of the coal would be known before shipment. Complaints on the severe clinkering of the ash came from only a fraction of the output of the mine but the occurrence of the clinkering seemed quite unpredictable. Attempts to relate the chemical composition of the ash and the fusion temperatures to the clinkering were unsuccessful. Coal from the area of the mine in which the fusion temperature of the ash was the lowest gave the least trouble from clinker-ing. Chemical analysis of the ash from that section giving the most trouble showed high contents of iron and low contents of silica, but frequently these were not greatly different from those of coals that gave little trouble from clinker. Aside from the clinkering difficulty, the coal was quite satisfactory. The ash content was normal and high rates of burning could be obtained, but again and again such severe clinkering would occur that the furnace would be shut down because of the accumulation of clinker. Examination of the clinker from the customers' plants showed that the clinkers that adhered to the grates and fouled the fuel beds were hard, flat, dense, and usually dark in color. Coal that was satisfactory gave clinkers that were softer, bulky rather than flat, of low density, and usually lighter in color.

Jan 1, 1944

By Raymond S. Weimer

Of the several characteristics of a coal that influence its suitability for use in a given piece of burning equipment, the clinkering and slagging characteristics of the ash of the coal are highly important. They determine the maximum rate at which the coal may be burned on a stoker or in pulverized form without difficulty from damage to metal parts, from erosion of refractory walls, or from stoppage of gas passages by accumulation on the tubes. They also determine the minimum rate at which a slag-tap furnace may be operated without difficulty in removal of the ash in fluid form. Need for a Better Criterion In common with other producers and users of coal, the Northern Illinois Coal Corporation has long used the available methods for the measurement of the clinkering characteristics of coal ash, chemical composition and fusion temperature of the ash, as criteria for the selection of coal that would suit the particular requirements of its customers. These two available criteria have greatly helped in the problem of selection but it is unnecessary to dwell upon the fact that they are not completely adequate for the purpose. The composition of the ash and its clinkering tendency vary widely over the company's mining area. In a certain period, some years ago, an unusual amount of severe clinkering of the ash of coal shipped made extremely acute the need for a better criterion of the clinkering that might be expected. It was also desirable that the criterion result from a reasonably rapid method, so that the clinkering characteristics of the coal would be known before shipment. Complaints on the severe clinkering of the ash came from only a fraction of the output of the mine but the occurrence of the clinkering seemed quite unpredictable. Attempts to relate the chemical composition of the ash and the fusion temperatures to the clinkering were unsuccessful. Coal from the area of the mine in which the fusion temperature of the ash was the lowest gave the least trouble from clinker-ing. Chemical analysis of the ash from that section giving the most trouble showed high contents of iron and low contents of silica, but frequently these were not greatly different from those of coals that gave little trouble from clinker. Aside from the clinkering difficulty, the coal was quite satisfactory. The ash content was normal and high rates of burning could be obtained, but again and again such severe clinkering would occur that the furnace would be shut down because of the accumulation of clinker. Examination of the clinker from the customers' plants showed that the clinkers that adhered to the grates and fouled the fuel beds were hard, flat, dense, and usually dark in color. Coal that was satisfactory gave clinkers that were softer, bulky rather than flat, of low density, and usually lighter in color.

Jan 1, 1944

By T. Reed Woodbridge

The object of this paper is to bring to notice a method in use at the Cedar Point laboratory of Witherbees, Sherman & Co., for determining the phosphorus in the ore mined at Mineville, N. Y. This ore is magnetite, with a gangue containing crystals of apatite. In 1886, Mr. H. F. Dawes, then head chemist at the works, suggested that as all the phosphorus seemed to be in the apatite, it could be obtained in solution by dilute nitric acid. After some experimenting the following method was adopted, and has proved invaluable for rapidity and ease; half a dozen determinations requiring very little more time or trouble than one. From + to 10 grammes of ore are weighed into a 150 c.c. beaker; 50 C.C. hot water and 10 c.c. strong nitric acid are added; the beaker is covered and the contents are boiled for 1/2 hour (10 minutes sometimes proves sufficient; but 4 hour is safer). The bumping which ensues if more than & gramme is used need cause no trouble. The hot solution is filtered into a 250 C.C. beaker. The filtration and washing (with hot water) proceed rapidly, as the magnetite itself is but slightly acted upon. After the addition of 15 C.C. ammonia and 15 c.c. nitric acid, the solution is cooled to 45' C., and from 15 to 40 C.C. of molybdic acid solution is added and stirred vigorously. In 5 minutes the precipitate will be down, and the determination can be finished by any good method. At Cedar Point the method more commonly used is weighing as yellow salt. Good washed filter-paper is used, No. 0 Swedish being preferred; and dozen 3 1/2-inch filters are numbered and dried and weighed at 110°C. These are always kept in stock. The yellow salt is filtered on one of these, washed with dilute nitric acid (2 per cent. by volume); dried for 1 hour at 110' C., and then weighed, 1.63 per cent. of weight being calculated as phosphorus. The filters vary in the two weighings from

Jan 1, 1889

By William R. Webster

At the Richmond mecting in February, 1901, I presented for discussion the proposed rail-specifications of Committee No. 1 of the American Section of the International Association for Testing Materials, with a review of their work, and other matters relating to the heat-treatment and chemical composition of steel (Trans., xxxi., 455). In order to bring out the views of our members on the important points referred to, I offered for discussion the following questions and comments (trans., xxxi., 972): " 1. The advantages to be gained by using more metal in the flanges and web of the heavier sections of rails.

Jan 1, 1903

By A. J. Teplitz, J. K. Rodgers, E. M. Pohoriles

This note is presented in order to call attention to a newly developed laboratory apparatus that appears to have interesting possibilities for the study of lost circulation of the pressure-parting type, for a more realistic evaluation of sealing materials for this type of loss, and for investigation of other aspects of hydraulic fracturing. A study of lost circulation, conducted jointly by operating divisions of the Gulf Oil Corp. and the Gulf Research & Development Co., has been in progress for the past few years. Earlier phases of the study dealt with mechanical factors contributing to loss of returns in laminar type sediments.' One aspect of this type of loss which has been widely discussed in the literature and elsewhere concerns the geometry of the fractures into which such losses occur. This subject is not merely a philosophical one, but has an important bearing on procedures for combating lost circulation difficulties and on other well operations. The further course of the collaborative studies previously mentioned has produced some information on this subject which, though limited in amount, is believed to be significant. In several typical cases of lost circulation in laminated shale and sand formations, the wells have been surveyed with instruments2,3 capable of detecting the points of loss with considerable accuracy. These wells were located in the Gulf Coast of Texas and Louisiana, in the Texas Panhandle, and in the Rocky Mountain area. In each of these instances the loss was shown to be occurring at some distance removed from the bottom of the hole and sharply confined to a very narrow interval, less than 1 ft in thickness. It is rather difficult to imagine that fractures of a vertical nature' would be of the limited extent indicated by the surveys in these wells. Furthermore, the high rates of loss at relatively low pressure differentials observed in some of these instances together with the narrow intervals involved would appear to require the radial flow pattern which would be associated with a more or less horizontal fracture plane. In view of the foregoing observations and records of successful squeeze cementing operations, in attempting to construct a laboratory apparatus For simulating pressure induced lost circulation, it was decided that the design should be based on a horizontal type of fracture. It was realized that5,6 Vhe production of horizontal fractures in a formation with non-penetrating fluid requires some mechanism for transmitting vertical components of the hydraulic forces to the plane of parting. This was accomplished, as will be evident in the description of the apparatus that follows, by providing recesses in the wall of the borehole which are believed to be representative of wellbore configuration found in Gulf Coast wells. The possible influence of such borehole irregularities on both pressure fracturing and the treatment of lost circulation appears to have been neglected in many studies of these subjects. It is believed that the present apparatus, incorporating features that take into account some of the factors mentioned, will provide means of gaining a further understanding of pressure induced fracturing and possibly for more realistically evaluating the numerous sealing agents, particularly the non-time-setting materials employed in treating the pressure-parting type of loss. DESCRIPTION OF APPARATUS The test cell used in the laboratory investigations is shown in Fig. 1. A schematic diagram of the entire system is shown in Fig. 2.

Jan 1, 1956

By Sir Robert A. Hadfield

The Hadfield method of producing sound steel ingots has been the subject of a paper read before the Iron and Steel Institute, so that it will be unnecessary to describe it fully here. The object of the method is to make poseible the production of steel ingots in which the pipe is almost entirely obliterated, and it is applicable particularly to the production of sound ingots, from which good rails could be rolled. The method in brief consists in casting the ingots on cars, usually with the small end down. Each ingot mold is provided with a sand top, rammed up in the well-known manner. After the mold is filled to the desired height with steel, a layer of slag about 0.5 in. thick is placed upon it and the balance of the mold is then filled with charcoal. Then, through suitable piping, an air blast is directed in numerous jets upon the charcoal, which is burned thereby, the combustion supplying addi, tional heat to the top of the ingot, which helps to keep the top fluid and to retard its solidification, while the lower parts are rapidly losing heat by its transfer to the mold. By one plan the ingots are cast in molds placed upon bogies, movable trucks, or platforms, in the position A, Fig. 1. The ingots are cast vertically on bogies, say four or more ingots on each bogie, as may be found most convenient, and the upper surface of the steel is maintained in a molten condition during the transit of the ingots from the casting pit to the stripper. This is effected by a series of air pipes, for example, three in number, with jets or holes on the under surface of such pipes, placed preferably horizontally, arranged in such a manner as to cause jets of air to impinge on the upper surface of the ingots. These holes or jets are made throughout the entire length of the overhead pipes, the length of such pipes being

Jan 1, 1914

By J. B. Mackintosh

The general method which has been followed since the time of Heinrich Rose, and perhaps before, for the determination of phosphorus in iron and steel, is to dissolve the sample either in nitric acid, aqua regia, or some other oxidizing agent, in order to convert the phosphorus into phosphoric acid. In 1832 Rose* recommends HNO3, or aqua regia, preferably the former. Wohler, in 1854,† directs that the iron should be oxidized by burning in a stream of oxygen for the determination of carbon, and the resulting oxide of iron containing all the phosphorus as phosphoric acid be treated as an ore. In the fourth English edition of Fresenius' Quantitative Analysis,† pp. 666-667, we find directions to dissolve the iron in aqua regia or bromine; and, coming down to more recent times, we find F. A. Cairns § directing the employment of a boiling solution of potassium chlorate and hydrochloric acid for the oxidation and solution of the sample to be analyzed. It is unnecessary to multiply quotations from the literature of the subject, though they might be extended almost inclefinitely, since it would only be a repetition of the above mentioned series of methods in one form or another; and the references given have been selected to show how little essential variation there is in the type-methods of solution used. In fact it seems to be universally accepted as a necessary first step in the determination that some such method of solution should be followed. One chemist, however, struck out on a different line of thought, and to the Lest of my knowledge only one, M. V. Tantin, who, in

Jan 1, 1886

By Milton Lissberger

MILTON L. LISSBERGER, ? New York, N. Y.-Solder is a mechanical mixture of tin and lead, a fact which is susceptible of very simple demonstration. A bar of solder of a grade even as low as 30 per cent. tin and 70 per cent. lead, passed through a buffing machine, will show a surface practically identical with that of a bar of second-quality or reclaimed tin. The buffings, on chemical analysis, will prove to be almost pure lead. According to the best practice, solder is made in the following manner. Virgin pig lead is first melted, and when it is thoroughly liquefied, virgin pig tin is added, together with a small amount of flux; the latter is for the purpose of bringing to the surface the so-called "liver," consisting of impurities that may have remained in either the lead or the tin as a result of incomplete refining. The combined material, when completely liquid, is thoroughly stirred for some hours, and is then cast into small pigs. Just before casting, and continuously during this operation, the molten metal yields dross, consisting largely of the oxides of lead and tin; this should be carefully skimmed off. After the pigs have cooled, they are taken to a smaller kettle, remelted, and cast into the desired shape for use; or if wires, ribbons, etc., are to be made, the solder is cast into slugs suitable for extrusion and rolling. During this second operation, the skimming of dross should be even more carefully done than at first. Hand mixing has proved to be the only reliable method for the production of the best quality of solder, irrespective of its percentages of lead and tin. The best quality of solder is not necessarily that which contains the highest percentage of tin, but rather is that composition which performs best on the required piece of work. In order to produce

Jan 12, 1918

By R. R. Angel

Drilling rate is a parameter that should be considered in determining the volume requirements for air and gas drilling. The use of past methods which ignore the effects of the solids content upon the pressure and velocity of the annulus flow stream can result in undercalculation of the required volurne by as much as 50 per cent. A vertical-flow equation is presented for determining volume requirements. This equation includes the effect of the solids that are transported up the annulus in the flow stream by incorporating the drilling rate as one of the parameters. The effect of down-hole temperature on required circulation rates is also ana-lvzed. A simple approximate method of determining volume requirements is presented. This method is more accurate than the methods used in the past. Hole cleaning difficulties are analyzed for a recent air drilling job where past methods indicated that - excess air was being used. Sample curves of calculated boitom-hole pressures are presented for air and gas drilling in several hole sizes. INTRODUCTION In certain areas the use of air or natural gas as a circulating medium for drilling oil and gas wells is becoming a common practice. Large increases in penetration rate and bit life are achieved through the use of these media in preference to mud or water. Drilling rates as high as 90 ft/hr have been obtained in shales. The importance of maintaining adequate circulation rate is generally recognized; however, much disagreement exists among drilling operators as to what constitutes "adequate" circulation rate. In quarry drilling, where annular velocities can be accurately determined, an annular velocity of 3,000 ft/min of standard air is required for best results in rocks having approximately the same density as those commonly penetrated in drilling oil or gas wells'. Although this standard air velocity has proven satisfactory for quarry drilling, some oil and gas well drilling operators believe that an equivalent annular velocity of more than 4,000 ft/min is required; others believe that as little as 2,000 ft/min . is sufficient. Much of this disagreement results from determining the required circulation rates with methods which fail to incorporate the drilled solids in an equation which is applicable to vertical flow. Hughes Tool Co. Bulletins No. 23' and 23-A3 present data for determining circulation rates based on the Weymouth formula. These data do not include the drilling rate as a parameter and, therefore, neglect the effect of the solids being transported up the annulus. In spite of this apparent defect and the fact that the Weymouth formula is not applicable to vertical flow, the Hughes data have well served the drilling industry in many areas and are important and timely contributions to the science of air and gas drilling. The Hughes data purposely omit a correction for increasing down-hole temperature. At slow drilling rates this effectively compensates for the use of a formula which is not valid for vertical flow; however, volumes determined by the Hughes method are not sufficient to support rapid drilling rates at moderate and great depths. For example, Phillips Petroleum Co.'s Cauthorn "D" No. l in the Vinegarone field for Val Verde County, Tex., was air drilled from 1,500 to 9,300 ft using a compressor delivering 1,400 cu ft/min. The 8 3/4-in hole was drilled with 5-in. drill pipe, and drilling rates as high as 90 ft/hr were obtained between 7,000 and 9,300 ft. No water or caving hole was encountered. At 7,728 ft it was necessary to wash-out 60 ft of cuttings to reach bottom after a trip to change bits. At 8,130 ft a twist-off occurred and the drill col-lars were stuck in drill cuttings. These difficulties indicate that the 1,400 cu ft/min of air was not sufficient to keep the hole clean. Hughes data indicates that 1,180 cu ft/min is sufficient to produce an annular ve-

Jan 1, 1958

By Allen F. Agnew

Geologic studies for the Federal and State governments in the Wisconsin-Illinois-Iowa zinc-lead district were begun in 1835, and subse¬quent surveys were made in the three states at in¬tervals until 1916, see Table I. The current study of the district, Fig. 1, by the U. S. Geological Survey was begun in 1942 in the hope that a systematic investigation would help in¬crease production of zinc and lead, then in ex¬tremely short supply. Major emphasis of the USGS program was on detailed mapping of the geologic structure and ore deposits. Preliminary maps and reports covering localities of intensive mining ac¬tivity have been published during the course of this study, Fig. 2. By 1950 the objectives of the study by the USGS were revised; 7Y2-min quadrangles of relatively unprospected localities as well as inten¬sively mined localities are now being mapped in Wisconsin. Since 1945 the investigation in Wiscon¬sin has been made in cooperation with the Wiscon¬sin Geological and Natural History Survey, and since 1951 the geologic mapping of areas of particu¬lar interest in Iowa has been performed in coopera¬tion with the Iowa Geological Survey. At intervals since 1943 the Illinois State Geological Survey has mapped the geologic structure and ore deposits of localities in the Illinois part of the mining district, see Fig. 2.

Aug 1, 1955