Search Documents

By W. C. Hauber

Techniques previously published to predict the production performance of a water flood when the mobility ratio is not unity have been primarily restricted to a five-spot well pattern. When other types of well patterns are considered, the prediction of performance has required either a model study or a complex numerical solution of a multiple-fluid system with a high-speed digital computer. Simple methods are developed in this report for predicting the areal sweep efficiency and injectivity history of a water flood for arbitrary well patterns and mobility ratios. The effect of an initial gas saturation can be incorporated into this method of prediction. With the layer superposition concepts published by Prats, et al.,1 these methods can be used to predict the production performance of a water flood in a reservoir having a wide range in permeability. A reasonably good agreement is shown by comparisons of the results calculated by this method with those obtained either by model studies or by complex numerical solution of multiple-fluid systems. Therefore, it has been concluded that a reasonably accurate method has been developed for predicting the production performance of a water flood employing an arbitrary type of well pattern for any given mobility ratio. A medium-speed digital computer can be used in applying this method. INTRODUCTION Production performance of multi-fluid five-spot water floods can be predicted by the techniques published by Prats, et al.1 This technique takes into account the effects of initial gas saturation, mobility ratio and vertical variations in horizontal permeability. A basic assumption in applying this technique is that unit displacement efficiency does not vary with time after the passage of the flood front. Prats, et al. demonstrated that this assumption is valid for normal waterflood applications with small mobility ratios. To extend Prats' technique to other types of well patterns has required either an experimental model study or a numerical solution of a multiple-fluid system to describe the performance of an individual homogeneous layer. Sheldon and Dougherty2 presented an exact numerical solution employing any arbitrary well pattern. This technique is complex to apply, requiring (1) numerical solution of the single-fluid system, (2) conformal mapping of the streamlines and iso-potential lines to form a new grid network, and (3) a numerical solution of the multi-fluid system on the new grid network. A method was developed in this paper to approximate areal sweep efficiency and injectivity as functions of time for an individual homogeneous layer for arbitrary well patterns and mobility ratios. Analytic expressions were derived to directly apply this method to five-spot and direct line drive well patterns. For other types of well patterns, this method is similar to the approach of Higgids and Leighton,6 in that it utilizes the stream tubes and iso-potential lines obtained by the solution of differential equations when the mobility ratio is unity. However, this method is easier to apply than the Higgins-Leighton method since it does not require knowledge of the variation between oil and water relative permeabilities and saturation. Using the relationship between areal sweep efficiency, injectivity and the volume of water injected into an individual homogeneous layer as obtained by the method presented in this paper, and Prats' technique for the superposition of individual layers, one can predict the production performance of any water flood. ASSUMPTIONS GENERAL Basic assumptions made in this report are that fluids are incompressible and the layers are horizontal, homogeneous and uniformly thick. It is assumed that as water is injected into the layer, three distinct regions are formed —a water bank, an oil bank, and an unflooded region. Each region is assumed to displace other regions in a pis-tonlike manner, with only one fluid flowing in each region, so that there is no change in unit displacement efficiency with time after the flood front has passed in the reservoir. Therefore, the residual oil saturation in the water bank and the oil saturations in the unflooded region are constant throughout the layer. The ratio (F) of the bulk volume of a layer occupied by the oil and water banks at any time before oil breakthrough, to the corresponding bulk volume of a layer occupied by the water bank, is given' by the equation BREAKTHROUGH AREAL SWEEP EFFICIENCY To predict the behavior of any type of waterflood pattern, one must know the breakthrough areal sweep efficiency Eb(Mc,o, F) for the pattern for any water:oil mo-

Jan 1, 1965

By W.G. Woolnough

There has been no noteworthy increase in production during 1935; but, on the other hand, there have been ample manifestations of a considerable increase in interest and activity in connection with petroleum prospecting. The Lakes Entrance field, in the State of Victoria, on the coast some 120 miles east of Melbourne, remains the only actual producer; and this production, consisting of lubricating stock devoid of light fractions, is very small in amount. Arrangements have been completed under which a series of "scout bores" for structure testing in the region of Lakes Entrance will be sunk by the Government of the State of Victoria, assisted by a subsidy from the Federal Government. Prospecting In the State of New South Wales, brilliant geological research in very difficult country, carried out by geologists of Oil Search Ltd., has revealed several previously unsuspected domal structures in the Sydney-Newcastle coal basin. These have been mapped in detail, and a test well is being sunk at Kulnura, 10 miles west of Wyong and 40 miles north of Sydney. At the date of writing this well has reached a depth of 1250 ft., 10-in. casing having been set at 1248 feet. Superficial formations consist of the Hawkesbury sandstone and Narrabeen beds of the Hawkes-bury system (fresh-water Triassic). It is anticipated that the upper coal measures of the Kamilaroi (Permo-Carboniferous) will be entered almost immediately. The objectives of the drilling are the upper and lower marine beds of the Kamilaroi system, which are regarded as promising as potential source—and reservoir—beds for oil. At Mulgoa, 30 miles west of Sydney, a bore is being sunk by the same company, Oil Search Ltd., to test for natural gas on a well defined structure located by the company's geologists. Noteworthy flows of gas have been encountered, but nothing approaching a commercial supply has been struck. It is considered probable that the gas has been derived

Jan 1, 1936

By W. G. Woolnough

There has been no noteworthy increase in production during 1935; but, on the other hand, there have been ample manifestations of a considerable increase in interest and activity in connection with petroleum prospecting. The Lakes Entrance field, in the State of Victoria, on the coast some 120 miles east of Melbourne, remains the only actual producer; and this production, consisting of lubricating stock devoid of light fractions, is very small in amount. Arrangements have been completed under which a series of "scout bores" for structure testing in the region of Lakes Entrance will be sunk by the Government of the State of Victoria, assisted by a subsidy from the Federal Government. Prospecting In the State of New South Wales, brilliant geological research in very difficult country, carried out by geologists of Oil Search Ltd., has revealed several previously unsuspected domal structures in the Sydney-Newcastle coal basin. These have been mapped in detail, and a test well is being sunk at Kulnura, 10 miles west of Wyong and 40 miles north of Sydney. At the date of writing this well has reached a depth of 1250 ft., 10-in. casing having been set at 1248 feet. Superficial formations consist of the Hawkesbury sandstone and Narrabeen beds of the Hawkes-bury system (fresh-water Triassic). It is anticipated that the upper coal measures of the Kamilaroi (Permo-Carboniferous) will be entered almost immediately. The objectives of the drilling are the upper and lower marine beds of the Kamilaroi system, which are regarded as promising as potential source—and reservoir—beds for oil. At Mulgoa, 30 miles west of Sydney, a bore is being sunk by the same company, Oil Search Ltd., to test for natural gas on a well defined structure located by the company's geologists. Noteworthy flows of gas have been encountered, but nothing approaching a commercial supply has been struck. It is considered probable that the gas has been derived

Jan 1, 1936

By John Hall

(New York Meeting, October, 1913.) THE Fremont test for measuring the energy consumed in breaking a notched bar of steel is not so well known in this country as it deserves to be. The test specimen used in this test is about 3/8 by 1/4 by about 11/4 in., notched with a hack saw on the lower side to cause the piece to break at a fixed point. A weight of 10 kg. falling 4 m., and provided with a knife or. chisel which strikes the specimen, breaks the test piece by impact. The residual force in the falling weight after it has broken the specimen is recorded by a suitable device, and the difference between the total energy and the residual energy of the weight (in kilogrammeters) is the force consumed in breaking the specimen. An experience of several years with the Fremont testing machine has shown its great value in readily detecting brittleness not revealed by tensile testing or slow bending testing. In this paper it is proposed to discuss (1) the supersensitiveness of the test as applied to cast steel and (2) its value in revealing the effect of heat treatment under certain conditions.

Jan 7, 1913

By R. D. Carter

Methods are presented for calculating the performance of multiwell gas reservoirs. These methods account for two-dimensional, unsteady-state flow of a non-ideal gas through a heterogeneous formation. The performance can be obtained for gas reservoirs with known physical properties and configuration subjected to specified development and production schedules. These methods may prove helpful in optimizing the exploitation of gas reservoirs. The numerical solrrtion procedures given for this non-linear problem are extensions of known techniques for the linear diffusion equation. Two of these procedures are based on a new difference equation given by Saul'ev. Limitations and advantages of these procedures are discussed. An example solution is presented and is used to compare the calculation methods. INTRODUCTION Li planning the operation of a multiwell gas reservoir, it is desirable to predict its performance for each alternate development and producing schedule under consideration. This paper presents three numerical procedures that can be used to calculate such gas reservoir performance using a digital computer. These methods account for two-dimensional transient flow of a non-ideal gas within the reservoir. Extension of these methods to three-dimensional flow is possible. The paper is divided into three parts. The first describes the problem for which a solution is wanted and three numerical procedures that can be used to obtain solutions. The second discusses the information necessary to set up a problem. This part will be of greatest interest to the field engineer. The third gives data and results for an example problem. PROBLEM AND SOLUTION METHODS In the following development, a gas reservoir is regarded as a sealed, porous, permeable, heterogeneous body in which a single, non-ideal gas phase is flowing. Flow is permitted in the x- and y-horizontal directions, but is considered to be negligible in the vertical or z-direction. The reservoir can be tapped by one or more wells. Methods to be described provide a basis for calculating the complete performance of the reservoir, including rates and cumulative production from the wells, and pressure distribution and decline in the reservoir. If the isothermal flow of a non-ideal gas obeying Darcy's Law occurs in two dimensions in a region R, the governing equation in this region is:

Jan 1, 1967

By H. J. Morel-Seytoux

The influence of patten, geometry on assisted oil recovery for a particular dispIacement mechanism is the object of investigation in this paper. The displacement is assumed to be of unit mobility ratio and piston-like. Fluids are assumed incompressible and gravity and capillary effects are neglected. With these assumptions it is possible to calculate by analytical methods the quantities of interest to the reservoir engineer for a great variety of patterns. Specifically, this paper presents (1) very brieily, the methods and mathematical derivations required to obtain the results of engineering concern, and (2) typical results in the dorm of graphs or formulae that can be used readily without prior study of the methods. Results of this work provide checks for solutions obtained from programmed numerical techniques. They also reveal the effect of pattern geometry and, even though the assumptions of piston- like displacement and of unit mobility ratio are restrictive, they can nevertheless be used for rather crude but quick, cheap estimates. ,These estimates can be refined to account for non-unit mobility ratio and two-phase flow by correlating analytical results in the case M = 1 and the numerical results for non-piston, non-unit mobility ratio displacements. In an earlier paper1 it was also shown that from the knowledge of closed form solutions for unit mobility ratio, quantities called "scale factors" could be readily calculated, increasing considerably the flexibility of the numerical techniques. Many new closed farm solutions are given in this paper. INTRODUCTION BACKGROUND Pattern geometry is a major factor in making water-fIood recovery predictions. For this reason many numerical schemes have been devised to predict oil recovery in either regular patterns or arbitrary configurations. The numerical solutions, based on the method of finite difference approximation, are subject to errors often difficult to evaluate. An estimate of the error is possible by comparison with exact solutions. To provide a variety of checks on numerical solutions, a thorough study of the unit mobility ratio displacement process was undertaken. To calculate quantities of interest to the reservoir engineer (oil recovery, sweep efficiency, etc.), it is necessary to first know the pressure distribution in the pattern. Then analytical procedures are used to calculate, in order of increasing difficulty: injectivity, breakthrough areal sweep efficiency, normalized oil recovery and water-oil ratio as a function of normalized PV injected.

Jan 1, 1967

By R. C. Mahon

The Homer iron-ore mine is at Iron River, Mich. Because it covers a large area, 400 acres, and because there was a considerable depth of water in the glacial drift above most of the ore bodies, this mine has presented a number of unusual and often difficult operational problems. The purpose of this paper is to discuss a few of the most important problems encountered. Surface Water Mining on this property was started on one 40-acre tract. The ledge in this area was the highest on the property and, although it was a real problem, water could be handled by underground pumping. During the first period of mining, drifts were driven just under the ledge and holes were drilled through to the surface material. In later years these drifts have been extended wherever possible. Although these drifts assisted in the drainage problem, it was evident they would not be sufficient alone. Before mining on a large scale could be started on this property, the water problem had to be solved. A number of test holes were put down to the ledge, and showed that there was an average 150 ft. of water-saturated glacial drift above the ledge over the rest of the mine. The upper 70 ft. was gravel and sand and the lower 80 ft. clay and hard pan, with some narrow seams of sand and gravel. It was evident that the water above the clay seam could not be drained off through openings in the ledge and for that reason it was decided to install surface drainage wells. This method of drainage was entirely new at that time and was pioneered at the Homer mine. The sinking of the first well was started in June 1929. Immediately following the first well a number of wells were sunk, but only to the top of the clay seam. This was done with the idea that a greater capacity could be obtained in a shorter time from gravel seams where the water flowed more freely and that the cost of pumping the water above the clay seam would be considerably less than if the wells had all been sunk to the ledge at once. Before the drainage of surface water was started, 1200 gal. per min. against a head of 800 ft. was being pumped from the mine. By March of 1932, with five surface wells in operation, the mine pumping had been reduced to 150 gal. per min. At this time we were pumping 5000 gal. per min., under an average head of 110 ft. from the surface wells. The total pumping costs were 30 per cent less than in 1929 because the greater capacity was being pumped at a much lower head. From 1932 to 1936 the mine was idle and all surface pumping was stopped. Since 1936, 10 new wells have been added with a total pumping capacity of 8000 gal. per min. at the present time. The water level has been lowered 70 ft. since surface pumping was started in 1929, and it is now approximately at the top of the clay. To remove the water below the clay seam, 11 of the 15 wells were sunk to the ledge.

Jan 1, 1946

By Charles J. Deegan

The purpose of this paper is to point out some features of the position of fuel oil and it's relationship to the economic balance and price structure of the petroleum industry. The term "fuel oil" as used in this paper includes crude used as fuel as well as refined gas oil and fuel oil. The period covered, from 1922 to date, may be characterized as the new normal era after the post-war inflation and deflation. In order to establish a proper perspective, the figures on consumption of the principal products of petroleum are shown in Table 1. This table shows that fuel oil and gasoline made up the bulk of the total demand in 1928 just as they did in 1922. There has been so much comment about the enormous increase in gasoline consumption that it may come as a surprise to some people to find that fuel oil is still at the head of the consumption list, in point of volume at least, and seems likely to hold that place for at least another year. Having established the fact that gasoline and fuel oil are by far the most important products, the remainder of this paper will deal almost entirely with these two items.

Jan 1, 1929

Officers of the Institute have been entertained by, members at nine meetings in different parts of the country during the months of March and April. Institute policies have been discussed by the officers and by members present at the different meetings, with the result of bringing about a better understanding of Institute policy among the members; it has also been made clear how various suggestions are viewed by members who are not all in close touch with Institute activities and with the policy of the Board of Directors. President Jennings devoted his remarks chiefly to an account of Institute activities in connection with Government service for the war, and presented an able address on the relations of labor and capital; with special relation to possible changes that may be necessary during the reconstruction period following the war. This carries forward the suggestion made by him in taking up the reins of government at the Annual Dinner on February 20, 1918, and makes available a paper which has aroused great interest at the different meetings; this address will be found on a following page. In referring to Institute activities in connection with the war, the President mentioned especially the Naval Consulting Board, the War Committee of Technical Societies, the War Minerals Committee, and the census of engineers prepared not only by the Institute in connection with the Bureau of Mines, but also by the American Society of Civil Engineers, the American Society of Mechanical Engineers and the American Institute of Electrical Engineers. He announced also the appointment of two committees, one on ferrous and one on non-ferrous metals, advisory to the Tariff Commission, and the appointment of a member of the Committee on the Excess Profit Tax, having especially to do with the question of excess profit taxes on gold mines. He also announced the appointment of a new committee known as the Committee on Industrial Organization, which will devote its energies largely to the question of relations of capital and labor and of "human engineering."

Jan 5, 1918

By Robert H. Aborn, J. J. B. Rutherford

It is now well known that troublesome intercrystalline corrosion may occur in austenitic stainless steels following exposure of the metal to a temperature within the range 1000° to 1500° F. (540° to 815° C.). The present paper describes a satisfactory method of estimating the extent of such corrosion, based on the measurement of the electrical resistance of a specimen before and after attack. This new method enabled us to study quantitatively the effect of several factors upon intergranular corrosion in the 18 Cr, 8 Ni type of alloy. The results show that susceptibility to this attack increases with increasing carbon content and grain size and appears to pass through a maximum for certain combinations of temperature of sensitization and period during which the alloy was maintained at that temperature; and are in complete accord with our interpretation of the mechanism of this phenomenon. The method is probably applicable to other metals or alloys subject to intercrystalline attack, such as the aluminum alloys of the duralumin type. The methods hitherto in use for estimating the degree of intergranular attack fall into three types: (1) microscopic examinationll (2) macroscopic examination of fractures, and (3) determination of the time required for complete failure or disintegration.2 None of these lends itself very well to a measurement of the extent of corrosion. The first two are qualitative in nature and the third provides an arbitrary value largely dependent on individual judgment, since failure is a progressive phenomenon and not a sudden event. Our experience is that weight-loss determinations, although valuable in some types of corrosion investigations, bear no simple relation to intercrystalline corrosion in this type of alloy, as is to be expected since the phenomenon probably involves only the thinnest films between adjacent metallic grains. Measurement of electrical resistance has been used recently in the study of some types of corrosion,3 but seems not to have been applied to

Jan 1, 1932

By J. L. Taylor, Pol Duwez

THE present knowledge of the Ti-Al system is limited to the portion of the diagram extending from pure aluminum to the intermetallic compound TiAl3' A preliminary investigation of the titanium-rich Ti-A1 alloys revealed that the solubility of aluminum in titanium is quite extensive and that the transformation temperature of titanium is raised by alloying with aluminum. From an X-ray diffraction study of alloys containing up to 75 atomic pct Al (TiAl3), the phase boundaries at 750°C were located as follows: the a titanium solid solution extends from 0 to about 36 atomic pct Al, a two-phase region exists from 36 to 46 atomic pct Al, and an intermediate phase of varying concentration extends from 46 to 62 atomic pct Al. The purpose of the present paper is to describe the crystal structure of this new phase. The alloys were prepared by melting in a helium arc furnace on a water-cooled copper plate, using a furnace essentially the same as that described in ref. 2. The titanium metal was of the iodide type furnished by the New Jersey Zinc Co., and a piece of pure aluminum (99.99 pct) was obtained through the courtesy of the Aluminum Co. of America. After melting, the samples, weighing approximately 5 g, were sealed in evacuated fused silica tubes and homogenized for 4 hr at 1000°C. The specimens were then held for 10 days at 750°C and rapidly cooled to room temperature. Filings were then taken from each sample, sealed in evacuated vials, annealed at 750°C for 4 hr, and rapidly cooled to room temperature by quenching the vials in water. Powder diffraction patterns were obtained with a 14.32 cm diam camera, using K copper radiation filtered through a nickel foil. Structure Determination The X-ray diffraction patterns of the alloys containing 46, 50, 55. 60, and 62 atomic pct Al were identical, except for a slight shift in the positions of the reflections. The alloy containing 55 atomic pct Al was chosen far structure determination. The powder pattern contained 37 reflections and the a, doublets were well resolved in the back-reflection range. The relatively small number of reflections and the sharpness of the pattern were considered as an indication of a simple atomic arrangement in a relatively small unit cell of high symmetry, and an attempt was therefore made to solve the structure without single crystal work. A satisfactory fit was found on a large scale Hull-Davey tetragonal chart for an axial ratio of approximately 1.45. All the reflections were readily indexed and the tentative unit cell dimensions were computed to be a - 2.81 kX, c - 4.07 kX, and c/a = 1.448. The indices (hkl) and the values of d and sin2 A are given in Table I. The agreement between observed and computed sin2 is quite satisfactory. Once the unit cell was known, the details of the structure were readily found. First, it is obvious that the number of atoms per unit cell cannot exceed two, since more than two atoms would lead to a density greater than that of pure titanium. The next logical step is to assume that the two atoms occupy the corner and center of the cell. If this assumption is correct, the structure may be described as follows: space group D1, - P 4/mmm; one titanium atom in a: 000; one aluminum atom in d: 1/2 1/2 1/2: and no extinctions. Assuming this structure to be the correct one. intensities were computed by means of the usual equation: sin2 0 cos 0 where F is the structure factor; 8, the Bragg angle. and p, the multiplicity factor. The calculated values of intensities are compared in Table I with the visually estimated intensities. The agreement is quite satisfactory and the structure is therefore confirmed. The crystal structure of TiAl just described is the same as that of AuCu ordered. The AuCu ordered

Jan 1, 1953

By R. C. Mahon

THE Homer iron-ore mine is at Iron River, Mich. Because it covers a large area, 400 acres, and because there was a considerable depth of water in the glacial drift above most of the ore bodies, this mine has presented a number of unusual and often difficult operational problems. The purpose of this paper is to discuss a few of the most important problems encountered. SURFACE WATER Mining on this property was started on one 40-acre tract. The ledge in this area was the highest on the property and, although it was a real problem, water could be handled by underground pumping. During the first period of mining, drifts were driven just under the ledge and holes were drilled through to the surface material. In later years these drifts have been extended wherever possible. Although these drifts assisted in the drainage problem, it was evident they would not be sufficient alone. Before mining on a large scale could be started on this property, the water problem had to be solved. A number of test holes were put down to the ledge, and showed that there was an average 150 ft. of water-saturated glacial drift above the ledge over the rest of the mine. The upper 70 ft. was gravel and sand and the lower 80 ft. clay and hard pan, with some narrow seams of sand and gravel. It was evident that the water above the clay seam could not be drained off through openings in the ledge and for that reason it was decided to install surface drainage wells. This method of drainage was entirely new at that time and was pioneered at the Homer mine. The sinking of the first well was started in June 1929. Immediately following the first well a number of wells were sunk, but only to the top of the clay seam. This was done with the idea that a greater capacity could be obtained in a shorter time from gravel seams where the water flowed more freely and that the cost of pumping the water above the clay seam would be considerably less than if the wells had all been sunk to the ledge at once. Before the drainage of surface water was started, 1200 gal. per min. against a head of 800 ft. was being pumped from the mine. By March of 1932, with five surface wells in operation, the mine pumping had been reduced to 150 gal. per min. At this time we were pumping 5000 gal. per min., under an average head of 110 ft. from the surface wells. The total pumping costs were 30 per cent less than in 1929 because the greater capacity was being pumped at a much lower head. From 1932 to 1936 the mine was idle and all surface pumping was stopped. Since 1936, 10 new wells have been added with a total pumping capacity of 8000 gal. per min. at the present time. The water level has been lowered 70 ft. since surface pumping was started in 1929, and it is now approximately at the top of the clay. To remove the water below the clay seam, 11 of the 15 wells were sunk to the ledge.

Jan 1, 1945

ROESLER MAX-Geology of the Iron-Ore Deposits of the Firmeza District, Oriente Province, Cuba. Discussed by William Kelly, J. T. Singewald, Jr., B. L. Miller, J. D. Irving, L. C. Graton, C. P. Berkey 439 SINGEWALD, J. T., JR., AND MILLER, B. L.-The Manganese Ores of the Lafayette District, Minas Geraes, Brazil. Discussed by L. C. Graton, J. T. Singewald, Jr., F. Lynwood Garrison HARDER, E. C.-Manganese Ores of Russia, India, Brazil, and Chile. Discussed by J. T. Singewald, Jr., E. C. Harder 454 SCHRADER, FRANK C.-Geology and Ore Deposits of Mohave County, Arizona. Discussed by J. C. Anderson McDOWELL, J. SPOTTS-A Study of the Silica Refractories. Discussed by J. W. Richards, H. D. Hibbard, W. F. Rochow, J. B. Umpleby-: 460 PHALEN, W. C.-The Conservation of Phosphate Rock in the United States. Discussed by E. G. Spilsbury 462 NORTON, S., AND LEFEVRE, S.-The Magnetic Concentration of Low-Grade Iron Ores. Discussed by G. C. Foote, J. L. W. Birkinbine, F. L. Nason 462

Jan 4, 1917

By R. S. Shoemaker, F. W. McQuiston

MAGMA COPPER COMPANY San Manuel Division The San Manuel Division of Magma Copper Company is located about 40 miles north of Tucson. Tons of ore milled in 1973 .were approximately 19 million at a rate of 63,000 tons per day. From this, about 42,600 tons of copper concentrate was produced as saying approximately 1.070 MoS2 and 28.5% Cu. As with many copper ores, the San Manuel ore contains a small amount of gold, but in this particular case, much of the gold follows the molybdenite. Separation of the molybdenite from the bulk sulfide concentrate by flotation produces a moly concentrate containing 9170 MoS2, just under 1.070 Cu, and 0.44 oz Au per ton. Cyanidation of this material for gold recovery is the only practice of its kind known to the authors of this Monograph. After thickening, the final moly concentrate is filtered for subsequent repulping with cyanide and lime. Gold dissolution takes place in three agitators in series with the pulp from the agitators being filtered in two stages in disc filters. Between filtration stages, the cake is repulped with barren solution. Filtrate from both filters is the pregnant solution. The Merrill-Crowe recovery unit is comprised of two solution tanks and the usual clarifying filter, vacuum tower, zinc dust feeder and Merrill precipitate press. Because of the presence of finely divided sooty chalcocite in the molybdenum concentrate, the cyanide consumption of 55 pounds per ton is extremely high. A compensating factor, however, is the low copper, moly concentrate produced. Precipitation of the gold from the highly copper-contaminated solution requires 0.56 pounds of zinc dust and 0.28 pounds of lead acetate per ton, high figures when compared to normal cyanidation practice. The Merrill- Crowe precipitate assays approximately 28.5% Cu, 8% Zn, 156 oz Au and 197 oz Ag per ton. The San Manuel cyanidation plant is an outstanding and innovative development.

Jan 1, 1975

By Raymond C. Moore

The oil-producing districts of Kansas comprise the northern portion of the so-called Mid-Continent field. As shown in the accompanying map, these districts are located chiefly in the southeastern and south central parts of the state. A considerable area in southeastern Kansas, extending northward nearly to Kansas City, has long been known as oil territory, the productive wells being distributed in patches or spots of irregular size and shape, the location of which is controlled by conditions of rock structure, and by the texture and porosity of the "sands" beneath the surface. In south central Kansas, there are a number of producing fields, the location of which appears to be controlled chiefly by well-defined structure. The most important districts are those in Butler County, especially that in the vicinity of El Dorado, which was for a time the most productive district in the entire Mid-Continent field. Recently new production of importance has been brought in the vicinity of Peabody and present development is active to the north across Marion County. Tests in the western parts of Kansas have not been successful in finding new petroleum fields. Histoby The first well drilled for petroleum, in Kansas, was near the town of Paola, Miami Co., about 40 mi. southwest of Kansas City, in the summer of 1860, only a few months after the completion of the famous "Colonel" Drake discovery well in Pennsylvania. Kansas appears to be the second state to engage in a serious attempt to find oil by drilling. The Civil War caused the temporary abandonment of attempts at oil development in the state. It was in the vicinity of Paola, where numerous oil seepages had been observed, that the first well producing oil in commercial quantities was drilled,' where also gas was first piped to the city for commercial use. Prospecting spread southward into Linn County and northward into

Jan 1, 1921

By W. B. Gogarty, W. C. Tosch

A new recovery process for producing oil under both secondary and tertiary conditions utilizes the unique properties of micellar solutions (also known as microemulsions, swollen micelles, and soluble oils). These solutions, which displace 100 percent of the oil in the reservoir contacted, can be driven through the reservoir with water and are stable in the presence of reservoir water and rock. Basic components of micellar solutions are surfactant, hydrocarbon and water. They may also contain small amounts of electrolytes and co surfactants such as a1cohol.r. The specific reservoir application dictates the type and concentration of each component. A salient feature of [he process is the capability for mobility control. Micellar solution slug mobility, by way of viscosity control, is made equal to or less than the combined oil and water mobility. Mobility control continues with a mobility buffer that prevents drive water from contacting the micellar solution. Laboratory and field flooding have proven that the process is technically feasible and that surfactant losses by adsorption on porous media are small. Introduction projects are under way to recover the maximum amount of oil under the most favorable economic conditions.' : New techniques are being developed to increase oil recovery,3" Polymer solutions are becoming an important means of controlling mobility in a waterflood. Thermal methods such as in-situ combustion and steam injection are being used in reservoirs containing highly viscous crudes. Surfactant flooding is receiving attention as a method of reducing interfacial tension to increase recovery.*'" Exotic recovery processes have been considered primarily for ' perations. Economics are unfavorable in most cases for tertiary recovery. studies at the Denver Research Center of the Marathon oil CO. have led to a new oil recovery method.* Micellar solutions (sometimes called microemulsions, swollen micelles, and soluble oils) are used to recover oil by miscible-type waterflooding. Basically, these solutions contain surfactant, hydrocarbon, and water. The method can be used in either secondary or tertiary operations. First, thc concept of thc process is considered in terms of the requirements for an effective miscible waterflood ing operation. Next, micellar solution properties are described including structure, composition, and phase behavior with reservoir fluids. Fluid characteristics are then considered as related to mobility control, and, finally, laboratory and field results are presented to illustrate the efficiency of the process. Concept of the Process Unit displacement efficiency and conformance determine the effectiveness of any oil recovery mechanism. In theory, a miscible waterflood should be capable of a 100-percent unit displacement efficiency with a correspondingly high conformance. Requirements for the slug of a miscible waterflood include (1) 100-percent displacement of oil in the reservoir contacted, (2) controllable mobility, (3) the capability of being driven through the reservoir with water, (4) a low unit cost to enhance economics, and (5) the ability to remain stable in the presence of reservoir water and rock. Micellar solutions satisfy requirements for the slug of a miscible waterflood process. Our discovery that these solutions acted as though they were miscible by displacing all fluids in the reservoir and by being displaced by water solved the miscibility problem. Adequate mobility control is possible by variations in solution viscosity through compositional changes. Economic requirements are met since micellar solution costs below $6/bbl appear possible, Mi cellar solutions stabilize surfactant in the presence of reservoir rock and water, thus reducing the importance of the problem of surfactant loss by adsorption. Fig. 1 illustrates schematically how these solutions are used. Operations start with injection of a micellar solution slug that serves as the oil displacing agent. Next, a mobility buffer of either a water-external emulsion or water solution containing polymer (thickened water) is injected to protect the slug from water invasion. Finally, drive water (water used in a regular waterflood) is injected to propel the slug and mobility buffer through the reservoir. Reservoir oil and water are displaced ahead of the slug, and a stabilized oil and water bank develops as shown in Fig. 1. Stabilized bank saturations are independent of original oil and water saturations. This means that, for a particular type of reservoir, the displacement mechanism is the same under secondary and tertiary recovery conditions. Oil is produced first in a secondary operation. For tertiary conditions, water is produced first. Movement of the slug through the reservoir is stabilized by the mobility buffer. An unfavorable mobility ratio usually exists at the interface between the buffer and drive

Jan 1, 1969

By Paul A. Bailly

Geology is not the problem. Because of inflation, taxation, and politics more reserves are being reconverted to uneconomic resources than there are new reserves created by exploration and extraction technology.

Jan 1, 1976

By P. de Vitry, Oliver Bowles

THE conventional wire saw, introduced in the slate district of Pennsylvania by the Bureau of Mines in 1927, and used thereafter with remarkable success, consists of a three-strand steel cable having a diameter of 3/16 or 1/4 in. The equipment, methods used, and accomplishments have been described in previous reports.1-7 Similar wire saws have been used extensively in Europe, in quarries and in shaping blocks and slabs. During the period 1932-1937, competition in European marble quarries was keen, prices were declining, and orders were not abundant. When orders were received, there was generally an urgent call for speedy delivery. Because of the diversification of demands, it was impossible to maintain in stock marbles of the color, size, and thickness called for, therefore the material generally had to be fabricated after the order was received. The wire saw enabled stone mills to fill such orders promptly. With skillful handling, 7/8-in. slabs could be cut accurately and rapidly with this equipment. It was found, however, that, as the three-strand wire became worn, the cutting speed dropped rapidly and the cut became less accurate. To overcome these difficulties the junior author of this paper, after much experimentation, developed a new type of wire consisting of a single ribbon-shaped strand, twisted as shown in Fig. 1. To ensure straight sawing, the twist of the ribbon is reversed from right to left and vice versa every 25 ft. The reversal of the [ ] twist is shown in Fig. 2. This is not a new feature; it has been used to advantage with the three-strand wire both in Europe and America for several years. However, some difficulties arise in splicing the three-strand reverse-twist wire, and the claim is made that cutting is less accurate as the wire becomes worn. To make an endless belt, the ends of the single-strand wire are brazed together with

Jan 1, 1941

By P. de Vitry, Oliver Bowles

THE conventional wire saw, introduced in the slate district of Pennsylvania by the Bureau of Mines in 1927, and used thereafter with remarkable success, consists of a three-strand steel cable having a diameter of 3/1 6 or 1/4 in. The equipment, methods used, and accomplishments have been described in previous reports.1-7 Similar wire saws have been used extensively in Europe, in quarries and in shaping blocks and slabs. During the period 1932-1937, competition in European marble quarries was keen, prices were declining, and orders were not abundant. When orders were received, there was generally an urgent call for speedy delivery. Because of the diversification of demands, it was impossible. to maintain in stock marbles of the color, size, and thickness called for,, therefore the material generally had to be fabricated after the order was received. The wire saw enabled stone mills to fill. such, orders promptly. With skillful handling, 7/8-in. slabs could be cut accurately and rapidly with this equipment. It was found, however, that, as the three-strand wire became worn, the cutting speed dropped rapidly and the cut became less accurate. To overcome these difficulties the junior author of this paper, after much experimentation, developed a new type of wire consisting of a single ribbon-shaped strand, twisted as shown in Fig. I. To ensure straight sawing, the twist of the ribbon is reversed from right to left and vice versa every 25 ft. The reversal of the [ ] twist is shown in Fig. 2. This is not a new feature; it has been used to advantage with the three-strand wire both in Europe and America for several years. However, some difficulties arise in splicing the three-strand reverse-twist wire, and the claim is made that cutting is less accurate as the wire becomes worn. To make an endless belt, the ends of the single-strand wire are brazed together with

Jan 1, 1941

By Paul B. Barton

Unconventional mineral deposits are those that differ significantly from productive deposits in mineralogy, grade, or geologic setting. Thus, the initial representatives of each deposit type are, by definition, “unconventional” until they are exploited. The “unconventional” status changes to "conventional" because of economic shifts (e.g., bulk silver ores), because of technological innovations (e.g., froth flotation), or simply through the recognition of, and production from, novel mineral concentrations. Heretofore the discovery of new deposit types has been almost entirely accidental, but the long- established concept of the geochemical cycle provides a nearly untouched opportunity and challenge for the application of geochemistry in predicting novel, potentially economic, mineral concentrations.

Jan 1, 1983