Search Documents

Jan 1, 1918

By Rudolph G. Wuerker

WITH the growing complexity of ore dressing processes and the diversity of equipment, efficiency control has become increasingly important in beneficiation. In the case of iron ore dressing, there have been sporadic attempts1-3 to establish the optimum separation for various ores so that grade and recovery would be readily predictable. But no rigorous statistical analysis and graphical presentation of such tests could be found in the literature of this country. Tests Made with Iron Ores Expanding upon existing methods of plant supervision and efficiency control, an investigation was started in the ore dressing laboratory at the University of Illinois on the applicability of distribution analysis to iron ores. A sample of crude ore was obtained from the Ohio mine of Cleveland-Cliffs Iron Co. at Ishpeming, Mich., consisting mostly of alternating bands of hematite and siliceous gangue, both about ¼ in. wide. The ore was heavily coated with limonite, which often filled the cracks.

Jan 7, 1958

By Walter W. Fisher, Samuel Rudy

Secondary treated sewage effluent was substituted for normal process water in laboratory tests simulating froth flotation recovery of copper and molybdenum sulfides. Sewage effluent caused significant detrimental response in the flotation process. First, a voluminous, uncontrollable froth was generated, even in the absence of a frothing agent, that has little mineral carrying ability. Second, sewage effluent caused a small loss in copper recovery and a large loss in molybdenum recovery. The detrimental effects of sewage effluent on flotation were partially overcome by tertiary treatment of the effluent by activated carbon adsorption and anion exchange. The frothing problem was significantly reduced after treating the sewage effluent by foam fractionation. Dilution of the effluent with normal process water resulted in a significant improvement in metal recovery. In addition, the large loss in molybdenum recovery was overcome by using a secondary collector in a combination reagent schedule. However, the secondary collector caused an appreciable loss in copper recovery.

Jan 1, 1979

By Sid T. Killan

The utilization of the reducing power of blast-furnace gas can be estimated by applying two rectifying calculations to the gas analysis. A resulting corrected CO/CO2 ratio varies inversely with furnace production. Directions for calculating the corrected CO/CO2 ratio are given, and a corrected CO/CO2 ratio is compared with actual furnace production. THE inadequacy of the normally accepted CO/CO, ratio as a measure of blast-furnace performance and furnace efficiency was discussed following the presentation of the paper by H. F. Dobscha.' In this outstanding example of careful observation on large scale blast-furnace operation, the changes occurring with beneficiated ores were: 1—A net gain in tonnage of 21.2 pct. 2—A decrease in net coke of 15.3 pct. 3—A decrease of 1.9 pct in the CO/CO, ratio. In this great change in furnace performance, the CO/CO, ratio proved itself worthless. The discussion of the inadequacy of expressing furnace performance and efficiency by the CO/CO, ratio led indirectly to the calculations forming the basis of this paper. At that time Dr. T. L. Joseph said: "We must consider difference in CO, from the stone in the two cases when we talk about the ratios of CO/C02." This statement is used for the second of the two CO/CO, ratio corrections forming the basis of this paper. The research work in attempting to find out why the furnaces could op-erate so differently with practically the same CO/CO, ratio lead not to the answer sought but, after a shift to the gaseous phase in the research work, the proof that the normal CO/ CO, ratio was outmoded and a new corrected ratio should replace it. To be of any value, any new corrected ratio should express approximate furnace efficiency and give an idea of practical furnace performance to be expected. This the normal CO/CO, ratio has failed to do. However, in the absence of anything better, some credence has been attached to the normal CO/CO, ratio. As far as the writer can ascertain, the present paper is the first attempt to change or improve the normally accepted index of

Jan 1, 1952

By W. H. Young, P. D. Torrey

The Eastern fields comprise a distinct geological and geographical unit, located in the northern part of the Appalachian geosynclinal prov-ince. In this area are the fields of New York, producing from rocks of Devonian, Silurian and Ordovician age; the fields of western Pennsylvania, where oil and gas occur chiefly in rocks of Mississippian and Devonian age; the fields of eastern Ohio, where oil and gas are obtained from rocks of Pennsylvanian, Mississippian and Silurian age; and the fields of West Virginia, where oil and gas are produced from rocks of Pennsylvanian, Mississippian and Devonian age. Many of these fields are of great antiquity in comparison to the age of the producing areas in a greater part of this country, and consequently in most instances it is impossible to obtain accurate historical statistics. In addition, the records of many of the more recently discovered fields are either unobtainable or are not sufficiently reliable to justify their incorporation in a review of this character. Rather than overemphasize certain fields and areas, where complete records are available, when there are many other fields of equal importance for which statistical data are not available, the authors have made a tabulation of development that does not take into consideration past operations and production. The records utilized in preparing this paper were derived largely from the scout reports of several of the larger companies, which generously made them available to the authors. These were independently tabulated by counties and townships, in order to eliminate as far as possible duplications and, excepting the Clinton fields of Ohio, where many of the smaller wells have not been individually reported, they represent the most accurate information available. Market conditions in both the oil and gas industry were far from favorable during 1932 and in consequence there was a total decline in drilling in the Eastern States, which is 22 per cent less than the number of completions in the preceding year. This decline was not constant over the entire area, as is shown in Table 1. The oil fields of both New York and western Pennsylvania were the scene of renewed drilling activity, which was largely restricted to the water-flooding operations in the Bradford and Allegany fields. Practically no new operations were started, but a certain number of new wells

Jan 1, 1933

Jan 1, 1918

By W. B. Clarke

It is the purpose of this paper to discuss briefly some of the recent developmellts in connection with the use of electrical apparatus for the mining of coal. For several years electricity has been employed extensively for the distribution of power, primarily for the operation of mine-locomotives and chain coal-cutters, and secondarily for motors driving pumps, ventilating-fans, rope-haulage, conveyors, crushers, auger-drills, coke-oven larries, etc. The severe and peculiar conditions which attend the development and distribution of power for the operation of coalmining machinery constitute a field to which the electricmotor seems to be especially adapted. The underground use of steam-engines, to any great extent, is impracticable for obvious reasons. The much higher efficiency of the electrical system is a potent argument in its favor as compared with compressed air, which, under ordinary circumstances, should only be employed for the operation of rock-drills and coal" punchers." The conditions in many mines prohibit the under-cutting of coal with a chain-machine; and the compressed-air " puncher," with its very low efficiency, is extensively employed. There have been no recent important improvements in the design and construction of the chain-machine, although, of course, minor changes are continually being made. More time and attention are being paid now than ever before to the details of mining-machinery, with the idea of eliminating the weaknesses which have been developed, and especially of facilitating repairs and renewals. Electric mine-locomotives are very extensively employecl for the haulage of coal on the main entries and the branchheadings; but in the majority of coal-mines the cars are still

Jan 1, 1904

By Graham Bright

The rapid increase in reliability, the low cost of operation, the ready application of safety devices, and the growing availability of central-station power have made the question of installing a hoist of the electric type no longer debatable. Where adequate electric power is available, there are few cases where it would be advisable to install a steam or air hoist. The type of electrical equipment depends largely on the nature of the power supply, its capacity, and the form of the power contract under which power is purchased. In a large majority of cases, the available electric power is alternating current, three phase, 60 cycles. There is, however, considerable 25-cycle power in use; and in a few instances constant voltage direct current is the only power available for a small or an occasional medium-size hoist. Where a new hoist is to be installed, the designer of the mechanical parts can readily take care of the maximum stresses likely to be imposed by the motor. Where the hoist is already installed and operated by steam or air and it is desired to substitute an electric motor for the engine, a careful check should be made to determine the advisability of using the old mechanical parts. In most cases it is better to install a complete new hoist than to attempt to use old mechanical parts. A steam engine has a definite maximum torque, which the hoist has been designed to withstand, while a motor may be able to deliver momentary torques beyond the strength of the mechanical parts of the hoist. The selection of the proper type of electrical equipment can only be made after complete information is obtained and certain calculations made to determine the capacities required. There are several methods used in making hoist calculations, but no matter what method is utilized a fair degree of familiarity with hoists and hoisting conditions is necessary before an intelligent analysis and proper selection can be made. Forms Used in Hoisting Calculations Some of the hoist calculation methods are long and complicated. Where such calculations are seldom made, it is better to use the

Jan 1, 1922

By R. L. Manegold

This paper outlines the reasons for and the application of suspended magnets above belt conveyors for the purpose of removing tramp iron to protect equipment. The design of a magnet strong enough to extract iron through a distance of 24 in. is described along with the proper method of application in the field. Advantages of the suspended magnet in contrast to the conventional magnetic pulley are also discussed. IN RECENT years there has been a decided trend toward bringing ores and coal out of open-pit and underground mines by long, sloping single-stage belt conveyors. Because the high investment cost of haulage conveyors dictates maximum speed and full loading for economy, conveyor belts are running faster than ever before, with a greater burden on the belts. In addition, larger blocks of ore are being mined and conveyed. Rougher use of large mining equipment generates more tramp iron; mechanical loading rejects nothing. Therefore the extraction of tramp iron and other deleterious materials for the protection of haulage conveyors at transfer points, chutes, and idlers is becoming an increasingly difficult job. In our experience, the best method of protecting long haulage conveyor belts is to extract the tramp iron, at least the large tramp iron, ahead of the main haulage conveyor or series of conveyors. It is most practical to collect the tramp iron at the earliest source possible, usually directly after the primary car unloading dump or after the primary crushers, which are ordinarily not affected by tramp iron, see Fig. 1. The coal or ore from its primary source is fed by chutes or feeders onto a buffer or shock belt conveyor, a short, ruggedly built conveyor system that can be considered somewhat expendable. Its primary function is to bring the ore up to speed for transmission to the haulage conveyor. There is no assured method of protecting this conveyor from tramp iron damage at its feed end. Likewise, there is a possibility, although remote if the magnet applied to this belt is installed correctly, that the tramp iron extraction process will damage the shock belt, which is, however, short and comparatively inexpensive. Magnetic head pulleys with their maximum effective range of about 8 or 10 in. cannot be considered for large installations, even though they are desirable because of the continuous and automatic tramp iron removal feature. Further, the most dangerous form of tramp iron with respect to potential damage to a haulage conveyor is the long rod, roof bolt, or rail segment, which is not extracted satisfactorily because of the limited tangential contact of such an iron shape with the magnet. Magnetic head pulleys are also undesirable because the dribble or fines from the head pulley discharge at the same point as the tramp iron. Screens must be used to separate the fines from the magnetics, resulting in additional expense and loss of head room. Magnetic detectors have been used with success, but they only indicate the presence of iron, and the conveyor belt must be stopped for its manual removal. The stoppage of any conveyor means that all preceding equipment must be stopped or a cascade of material on the idle conveyor will result. Occasionally combinations of detectors and magnetic head pulleys are used. The detector precedes the magnetic head pulley and detects only large pieces of tramp iron, while the magnetic pulley subsequently takes out the smaller ferrous metals. Suspended magnets overcome the disadvantages of magnetic head pulleys, detectors or a combination of both. There are several magnetic extraction problems involved in applying a suspended magnet at this

Jan 1, 1953

By R. L. Manegold

This paper outlines the reasons for and the application of suspended magnets above belt conveyors for the purpose of removing tramp iron to protect equipment. The design of a magnet strong enough to extract iron through a distance of 24 in. is described along with the proper method of application in the field. Advantages of the suspended magnet in contrast to the conventional magnetic pulley are also discussed. IN RECENT years there has been a decided trend toward bringing ores and coal out of open-pit and underground mines by long, sloping single-stage belt conveyors. Because the high investment cost of haulage conveyors dictates maximum speed and full loading for economy, conveyor belts are running faster than ever before, with a greater burden on the belts. In addition, larger blocks of ore are being mined and conveyed. Rougher use of large mining equipment generates more tramp iron; mechanical loading rejects nothing. Therefore the extraction of tramp iron and other deleterious materials for the protection of haulage conveyors at transfer points, chutes, and idlers is becoming an increasingly difficult job. In our experience, the best method of protecting long haulage conveyor belts is to extract the tramp iron, at least the large tramp iron, ahead of the main haulage conveyor or series of conveyors. It is most practical to collect the tramp iron at the earliest source possible, usually directly after the primary car unloading dump or after the primary crushers, which are ordinarily not affected by tramp iron, see Fig. 1. The coal or ore from its primary source is fed by chutes or feeders onto a buffer or shock belt conveyor, a short, ruggedly built conveyor system that can be considered somewhat expendable. Its primary function is to bring the ore up to speed for transmission to the haulage conveyor. There is no assured method of protecting this conveyor from tramp iron damage at its feed end. Likewise, there is a possibility, although remote if the magnet applied to this belt is installed correctly, that the tramp iron extraction process will damage the shock belt, which is, however, short and comparatively inexpensive. Magnetic head pulleys with their maximum effective range of about 8 or 10 in. cannot be considered for large installations, even though they are desirable because of the continuous and automatic tramp iron removal feature. Further, the most dangerous form of tramp iron with respect to potential damage to a haulage conveyor is the long rod, roof bolt, or rail segment, which is not extracted satisfactorily because of the limited tangential contact of such an iron shape with the magnet. Magnetic head pulleys are also undesirable because the dribble or fines from the head pulley discharge at the same point as the tramp iron. Screens must be used to separate the fines from the magnetics, resulting in additional expense and loss of head room. Magnetic detectors have been used with success, but they only indicate the presence of iron, and the conveyor belt must be stopped for its manual removal. The stoppage of any conveyor means that all preceding equipment must be stopped or a cascade of material on the idle conveyor will result. Occasionally combinations of detectors and magnetic head pulleys are used. The detector precedes the magnetic head pulley and detects only large pieces of tramp iron, while the magnetic pulley subsequently takes out the smaller ferrous metals. Suspended magnets overcome the disadvantages of magnetic head pulleys, detectors or a combination of both. There are several magnetic extraction problems involved in applying a suspended magnet at this

Jan 1, 1953

By J. Walter Snavely

PRESENT-DAY processing in many industries, calcining, sintering, briquetting, beneficiation and nodulizing, increasingly calls for the handling of large volumes of hot bulk materials. Various types of conveyors have been employed. This discussion will cover the factors governing their selection. For temperature ranges up to 400°F, or approximately 200 °C, a wide range of conveyors is available. Special constructions of rubber conveyor belts, steel conveyor belts, vibrating and shaker conveyors, apron conveyors, and drag chain conveyors, all are used successfully. As temperatures go well above 400 2F, however, choice of conveyors is narrowly limited. This paper will consider the problem of handling bulk materials only where the temperatures exceed 400°F. The arbitrary selection of 400 °F as a dividing point undoubtedly can be challenged, as special conveyor belting constructions are available which are suitable for temperatures in excess of 400°F. However, when the relatively short life of such belts and the cost of their replacement, with the attendant down time, are balanced against the reliability and long service life of the properly designed steel constructed units to be discussed, there is little question in any operator's mind that the special belts are more expensive to use. Because the conveyors under study are for the handling of bulk materials, inevitably including a high proportion of fines, obviously wire mesh belts cannot be included for consideration. Even though this type of conveyor is widely used at high temperatures, i.e., for carrying glassware through a lehr, it is unsuited for the conveying of bulk materials, and therefore will be excluded from further discussion in this paper. Preliminary to the study of the conveyor itself is the determination as to whether the material is to be cooled while it is being handled, or whether the processing requires retention of all heat and the maintenance of a given temperature range. In the majority of cases cooling is incidental to or part of the handling process, when the handling, for example, follows completion of sintering, roasting, calcining, refining, or some other process. To meet such operating conditions successfully, the conveying medium used must have: 1—a construction capable of withstanding maximum initial temperatures of the material being handled. 2—a construction providing efficient heat transfer for cooling. 3—a construction providing dependable operation and long life with minimum service requirements, and 4—a construction providing controlled and efficient conveying. Under the usual conditions of cooling during the handling, the construction selected to withstand the initial maximum temperatures does not necessarily involve using alloys, as excellent results can be achieved with normal carbon steels and cast irons, when they are properly applied and proportioned. The earliest and simplest type of conveyor for handling very hot materials is the cast steel drag chain conveyor, still widely used for handling hot cement clinker, as illustrated by Figs. I and 2. Because of the rugged and generous proportions of the chain link design, low carbon steels are entirely suitable for the links. The pins, however, must be alloy steel. The simple, rugged construction of this type of conveyor makes it readily capable of withstanding high initial temperatures, even though the chain is operating buried in the material. The drag-chain type of conveyor has advantages and limitations. Although the efficiency of the heat transfer is relatively poor, the life of the conveyor is reasonably long, and because of its crude simplicity it does not require much servicing. However, as a conveyor, it is limited in capacity, and largely limited to horizontal runs. Furthermore, because of the crude design, heavy weight, and the chain operating at the temperature of the material, greatly reducing permissible operating chain pulls, this type of conveyor is limited to relatively short centers. Another type of conveyor that has been used for very hot materials is the cast pan conveyor. Because of its very generous proportions the cast pan, which is made of either cast iron or malleable iron, can withstand initial maximum temperatures. It also provides efficient heat transfer for cooling. Further, it is on efficient conveyor construction, which can be used for inclines. Because the chain employs rolling friction instead of sliding friction, and is not in the maximum temperature zone, much longer centers are possible. It is this type of conveyor that is frequently used in the casting of various metal pigs, pig iron, and aluminum; it is obvious, therefore, that very high initial temperatures are being handled. With this kind of conveyor the return run is frequently sprayed with water to accelerate heat transfer. The build-up of residual heat in the very heavy cast pans is thus overcome. The outboard roller steel pan conveyor is an improved pan conveyor' which provides high rates of heat transfer and substitutes formed steel pans for the heavy cast pans. It is a very efficient conveying medium. The details of this particular construction are clearly shown in Fig. 3. An early application of this type of conveyor is shown in Fig. 4. In this case the conveyor units are handling roasted phosphate rock at average temperatures of 1000" to 1500°F, and frequent maximum temperatures as high as 1900°F. Several widths are used. The capacity of the unit at a speed of 50 fpm is approximately 30 tph per inch of width at peak loadings, average capacity being about 1/3 of peak loading. The assembled conveyor is shown in Fig. 5, with views of both the top and the underside to show all the construction details. In particular, the following general design principles were carried out in this construction:

Jan 1, 1954

By R. N. Orava

TO the author's knowledge, only one satisfactory high-resolution technique for etch-pitting dislocations in Cu-Zn alloys has been published.' In that account, pits in 70/30 brass single crystals were produced by etching electrolytic ally in a 30 pct orthophosphoric acid bath. Thereafter, observations were made from surface replicas by electron microscopy. The method of pitting and observation permitted the high resolution necessary for the distinction of individual dislocations in arrays of pile-ups. However, no comment was offered concerning the possibility of obtaining pits which are amenable to optical resolution. Moreover, for adequate results, the electrolytic pitting process is invariably preceded by a polishing stage which could obscure the surface features of interest. Consequently, it would be desirable to be able to delineate, by solely chemical means, dislocations which could be detected by both optical and electron metallo-graphic techniques. This was achieved by the simple expedient of modifying two etchants reported by young2 to reveal dislocations on the (100) planes of pure copper. Single crystals of 70/30 a brass, described previously,3 were sectioned to provide a surface parallel to a set of {100) planes, mechanically polished, and subsequently electropolished at 2.4 v in a solution comprised of 2 parts H3PO4, 4 parts ethanol, and 3 parts water. The inclusion of ethanol tended to inhibit nonuniform surface attack. Etch-pitting was effected by a 2 to 3 sec immersion in a 70 pct aqueous solution of HNO3. The samples were then washed in a fast-flowing stream of water, and rinsed further in distilled water, and ethanol, before drying. It is important to note that this reagent should be either used immediately after mixing, or, if allowed to cool, reheated to about 35°C prior to use. No pitting was obtained at room temperature. Typical results are shown in Fig. 1 where (a) is an optical view of the pitted surface and (b) is an electron micrograph of a silicon monoxide replica shadowed with tungsten oxide. The former is characteristic of a somewhat longer etching time (-6 to 8 sec) which varied with bath temperature. Similar pits accrued from a 1/10 aqueous dilution of another of Young's solutions2—2 M FeC1,6H20 and 7.8 M HBr.

Jan 1, 1968

By David Baker

In a paper presented to the American Institute of Mining Engineers, September, 1904, entitled uImprovements in the Mechanical Charging of the Modern Blast-Furnace,"' I showed the great fault of mechanical charging-devices to be that the materials charged by the dumping of the skip were separated, the coarse materials having high velocity, and the fine, low— thus giving paths of low resistance through the stock in the furnace, which resulted in unequal distribution of the furnace-gases, unequal reduction, slips, scaffolds, irregular cutting of the inwall, "of" iron, and increased fuel-consumption. I showed how this could be prevented by rotary distribution, through which the irregular distribution in one layer charged is compensated by charging the subsequent layers from succeesively varied positions of the charger, and becomes practically eliminated when the angle between two successive positions is a little more or less than an even fraction of a full circle. Of all the devices then on the market, the nearest approach to the ideal arrangement was found in the Brown distributor, a full description of which was given. The one defect pointed out, however, was the difficulty of maintaining so much mechanism on the top of a blast-furnace. Since the presentation of that paper, I have designed a very

Jan 1, 1907

By John B. Gayle

PRESENT flotation processes depend almost entirely on the buoyant properties of air bubbles to effect separations of mineral and gangue, but there is no convenient method for measuring aeration in flotation cells. Consequently the relation between aeration and cell performance has not been definitely established. In connection with a comparative study of kerosene and froth flotation processes, a modification of the displacement method' was developed in which air escaping from the cell surface is measured with a wet-test meter. The arrangement shown in Fig. 1 is satisfactory for use with a number of cells and is not critical, except that care must be taken to use connections and tubing large enough to avoid excessive back pressures. Attempts to use smaller tubing resulted in back pressures that caused displacement of the liquid level in the receiver, so that some air was lost around the sides, an occurrence readily visible when measurements were taken with only water passing through the cell. With the arrangement shown, the manometer indicated an average reading of about ½ -in. water pressure. No loss of air was evident.

Jan 7, 1958

By Clifford J. Lewis, James L. Drobnick

Vexed with competition from relatively high grade foreign orebodies, perplexed by marginal, low grade domestic orebodies, and ironically faced with the fact that practically every metal needed in our economy is available domestically in ample quantity in the ground, our mining industry awaits the advancements in beneficiation technology that will bridge the gap between the ground and the market place for our presently unexploited mineral reserves. Among the vast number of research and development projects underway in the metals mining industry, there are a few chemical techniques in metals winning that, with further development or wider application, could have a profound effect on the industry. These techniques include the Imperial Smelting and Refining Process for complex lead-zinc ores, chlorination and fused salt procedures, the liquid ion exchange process, and the field of non-aqueous leaching. IMPERIAL SMELTING PROCESS The Imperial Smelting and Refining Process is of interest because it offers a possible economic route for the processing of complex zinc-lead-copper ores. The process represents the outcome of the combined efforts of metallurgists and engineers of Imperial Smelting Corporation. Ltd., the United Kingdom Subsidiary of the Consolidated Zinc Corporation, Ltd., and is the subject of patents throughout the world. This process is essentially the employment of the blast furnace for the production of zinc. Zinc has always resisted blast furnace technology, primarily because of the difficulty of condensing zinc vapor from dilute gases. The Imperial Smelting Process employs a blast furnace working at ordinary pressures and in a system which is able to con- dense a blast furnace gas of a very low zinc content.

Jan 11, 1963

By Massimo Guarascio

Computer data processing and ore reserve evaluation techniques, mainly based on geostatistical methodologies, have been developed at Agip Mining Division with the assistance of the Department of Mining Engineering of the University of Rome. A number of computer programs are available when facing problems such as optimization of sampling patterns, minable reserve estimation, grade control of output, and so on. In the present paper, the aims and the criteria followed in developing these programs are discussed. Some recent examples of application are also cited.

Jan 1, 1977

In 1910, he was with the Hidalgo Guadalupe, Pachuca, Mexico, and in 1911 was engineer with the Gualcola Mines Co., at Tuquerres, Colombia. In 1913, he returned to the Sout.hwest, and was employed for that yea.r by the Inspiration Cons. Copper Co. at Miami, and in the middle of the following year he became engineer with the Detroit Copper Co., at Morenci. In the autumn of 1914, Mr. Reece, stirred by his English blood, resolved to return to England to take part in the war. At this time he wrote "I think it will be better for me to resign my membership. If I come through all right, I will apply for re-election." The Institute, however, instead of accepting Mr. Reece's resignation, voted him an indefinite leave of absence, and this precedent soon crystallized into the regular procedure, now in force, of remitting the dues of members in active service. On Dec. 17, 1914, he wrote from Montreal that he fully expected to go over shortly in the second contingent from Canada, with Borden's Armored Brigade, operating with armored motor cars. As he said "this will be active enough service to satisfy any enthusiast, as they are used generally for reconnaissance duty." Soren Ringlund Soren Ringlund died suddenly on July 24, 1918, at Fort Logan, Colo., where he was engaged in service with the Medical Department of the U. S. Army. Mr. Ringlund was born in Denmark in 1875. He came to the United States in 1902, and became a citizen in 1908. He graduated as

Jan 1, 1920

Accurate modeling of the semivariogram is an extremely important step in the geostatistical analysis of mineral deposits. Automatic fitting of a mathematical model is often possible but not necessarily desirable. Significant geologic and statistical information must be taken into account in the fitting process, which is not always available to the computer. Manual model fitting is, on the other hand, extremely time consuming. Interactive graphics are best suited to optimize the process. Many interactive methods are described, which are adapted to modeling semivariogram in one-, two-, or three- dimensional environments.

Jan 1, 1985

By AIME AIME

WHEN your good secretary was kind enough to ask me to speak tonight I was rather reluctant to do so lest it be just another case of a man who has been abroad inflicting himself on his friends. So if anybody wants to walk out on me it will be perfectly all right. In the matter of statistics, geography, geology, and the like, you can get more from an encyclopaedia than I can tell you. For that reason I want to restrict myself to mentioning just a few personal impressions of that great country, Australia. About ten days ago I met the professor of mining from the University of Adelaide. In our conversation, which ran into a discussion of the relative characterstics of the two countries, he asked me whether it was fair to think of Australia as a land of strikes and not think of the United States as the home of murderers, bootleggers, and gangsters. At any rate those are the things most prominently played up in the news from the respective countries, so you can see how distorted our conceptions can be.

Jan 1, 1931

By Edward J. Bagnall

The major raw material feed properties of size distribution and chemistry are examined in relation to their effect on sinter operating conditions, plant productivity, sinter physical quality, reduction- degradation characteristics and sinter texture and mineralogy. The resultant physiochemical properties of these sinters are related to their behaviour in subsequent ironmaking operations.

Jan 1, 1977