Search Documents

By Anson Hayes, John Chipman

The quality of sheet and strip products made of rimming steel is closely related to the structure and chemistry of the ingots. The variation in composition throughout the ingot, as affected by segregation, is of great importance, as are also the form and distribution of the voids that result from the gases evolved. It is because of this importance that the considerable literature in this field has accumulated. No attempt is made in the present paper to compile a bibliography of the excellent work that has already been done, as this has been adequately covered in the many excellent reports on the heterogeneity of steel ingots prepared by a joint committee and published by the Iron and Steel Institute.' From time to time, in any field of investigation new tools and new technique are developed, which make further progress possible. In the field with which this paper is concerned, this is true. The development of the vacuum-fusion method as a means of following oxygen segregation, and a technique for obtaining the volume and composition of the gases evolved during solidification, have opened the way to obtaining data by means of which some considerable progress has been realized in developing more of the detailed mechanisms of solidification and segregation in rimming-steel ingots. General Theory of Segregation The basic cause of segregation lies in the fact that the impurities are less soluble in solid than in liquid iron. The solid that forms from the impure liquid is more nearly pure than the liquid itself. If solidification proceeds slowly enough, or if the liquid and solid phases are maintained in contact with one another for a sufficient time, a condition of equilibrium is set up, which may be represented by a phase diagram. Portions of the

Jan 1, 1939

By Uwe Neis, K. Peter Kiefhaber

Whereas single particle flotation is considered to be evoked by physico-chemical bubble adhesion, floc flotation seems to be governed by other mechanisms. This study demonstrates that air bubble size does not affect the flotation efficiency of inorganic particles which have been destabilized by different means: 1. addition of simple salts and 2. polyelectrolyte dosage. The air-to-solids ratio A/S does not influence the solids removal efficiency within a broad range of examination. However, there is a significant difference between A/S-values necessary to obtain optimum flotation comparing both destabilization mechanisms. Polyelectrolyte concentration corresponding to complete particle destabilization at the isoelectric point leads to optimum sedimentation rates but not to optimum flotation efficiency. To obtain optimum solids removal by flotation higher polyelectrolyte concentrations are necessary resulting in a positive solids surface charge. These effects are explained on the basis of different floc structures.

Jan 1, 1980

By E. N. Cameron

GRAPHITE has been included in U. S. lists of strategic minerals since the problem of mineral deficiencies was revealed during World War I. Since 1918 the domestic graphite industry has led a precarious existence, and there has been much uncertainty as to the amounts of usable graphite of various grades that would be available from domestic sources in time of emergency. In 1950-1951 therefore, the writer, assisted by Paul L. Weis, undertook a review of domestic graphite sources for the U. S. Geological Survey.' The conclusions of this study are presented here, with a discussion of some technologic and politico-economic factors bearing upon the problem. Uses of Graphite: Natural graphite as marketed exhibits a wide range of properties, which determine the uses to which it is put. The most essential uses are in the manufacture of crucibles and related refractory articles, in lubricants and packing materials, and in the manufacture of batteries, foundry facings, pencils, and carbon brushes. Numerous specifications covering the mineral in its various applications must be met by producers and processors of graphite. The problem of supply is therefore not simply one of procuring a sufficient total tonnage, but the more difficult problem of procuring enough of each different grade to meet foreseeable needs. The amount of graphite required by American industry is not large. Ordinarily only a few thousand tons of strategic grades are consumed annually, yet the elimination of this small tonnage would have serious effects in several industries. Strategic Graphite: Since World War I, 60 to 100 pct of the country's annual supply of graphite has been furnished from imports. At present, natural amorphous graphite for use in pencils and batteries is produced largely from American-owned mines in Mexico. Graphite for foundry facings is obtained from a number of sources. Neither grade is a serious problem. High purity graphite for carbon brushes and for pencil leads, however, is imported, largely from Ceylon, in the form of amorphous lump graphite. Most of the flake graphite used for crucibles and related refractory articles is likewise imported, largely from Madagascar, and much of the lubricant and packing grade graphite used by industry is obtained from the same source. The strateg'ic grades of graphite are therefore amorphous lump of the Ceylon type, crucible flake, and flake suitable for lubricants and packing. Ceylon lump and Madagascar flake have for many years been accepted as standard by domestic consumers of graphite, and various essential manufacturing processes are geared to the use of graphite from these sources. Ceylon graphite as marketed is classified into several grades based on particle size and purity. Processing methods are said to be simple, but the products marketed are carefully graded and are consistent in their characteristics, an important matter to the consumer. Nearly all the graphite produced in Ceylon is from veins. Resources are reported to be large, labor is cheap, production costs are low, and world competition is slight—factors accounting for the commercial success of the graphite mining industry in Ceylon. Madagascar is reported to have deposits of the Ceylon type, but its output consists almost entirely of flake. Madagascar graphite as received in the U. S. is further processed by importing organizations, and a large number of grades are produced to meet industry requirements, especially those for crucible flake and for lubricant and packing grade flake. Madagascar crucible flake as marketed is noted for coarseness, uniformity, toughness, clean-

Jan 1, 1957

By Freeman Bishop

Senator Henry M. Jackson t D. Wash.) recently tossed a live grenade into the hardrock mining industry with proposed legislation to change provisions of the law governing Federally owned mineral values. Title Two of the measure would place hardrock mining agreements on a leasing basis similar to that which has applied to oil and gas since 1920. Known as the "Public Domain Lands Organic Act 01 1971" or S.921, the bill would monitor exploration by heavy machinery which ran destroy fragile ecology without any requirement for restoration or rehabilitation." Jackson said. Abandoned mining claims, lie continued, dot the public domain, "casting clouds upon the title to property which belongs to all the people.” and a minerals leasing system is "the most practical way of achieving the proper balance."

Jan 1, 1971

By J. D. Kalasky

Continuous mining has revolutionized the coal industry but intensified the problems of earlier mechanization. From the installation of the first miner, it was recognized that face ventilation would be one of these problems. To establish an efficient work cycle for the equipment being used, conventional mechanized mining provides four or more development faces. Continuous mining, relying on a single machine, requires only one face, although more than one can be driven alternately by the same machine. In gaseous areas mined by the older methods, the intermittent rate of exposure allows time for the face to bleed off or be cleared, and the width obtained with conventional units makes it possible to hang a brattice line almost to the face. Continuous mining increases the ventilation hazards; there is no margin of time, and very limited space. For all practical purposes, continuous miners available today can be grouped into two major types, rippers and borers. The two can be further classified, respectively, as flexible and rigid. Both types have been in operation in U. S. coal mines for the past five to ten years in a number of seams, under various conditions ranging from slightly gaseous to very gaseous. Common methods of face ventilation utilizing jute or plastic brattice material for line curtains, stoppings, and checks have so far met with success. Air volumes to operating sections are greater than for conventional mining, and specific instructions have been given to section crews stressing the precautions needed in dealing with a steady rate of gas emission and the importance of maintaining reasonably air-tight brattice to direct a good steady flow toward the face at all times. Operators of continuous miners, as well as the foreman on each section, are equipped with an approved safety lamp for gas testing. When the miner is in steady operation, tests for gas at the face are made at 15 to 30-min intervals, depending on the

Jan 1, 1960

By E. J. Hammer

Crushing and grinding of gypsum demands con- trolled processing to a fineness suitable for further treatment of the mineral into end products, and into various sizes of material which are themselves saleable products. The majority of gypsum tonnage ultimately ends up in stucco for wallboard. Therefore, mineral reduction is normally designed toward this end, but it is done in a manner that permits drawing off intermediate products to meet various customer requirements. This forces companies into compromises at times in equipment installations. Normally, 5 to 6 different sizes intermediate to the end product are marketed and these are generally the fineness of material to be used as stucco for wallboard. These sizes are produced by controlled crushing, grinding and sizing. How Ore Characteristics Guide Processing First, gypsum as a mineral (CaS0;2H,O) is number two on the Mohs scale two of hardness; only talc is softer, Despite being soft, gypsum is tough, a factor which is of critical importance when developing equipment specifications. In addition, of the increasing volumes of rock handled, the associated and included impurities such as anhydrite, silica or lime- stones are found to be relatively abrasive.

Jan 1, 1970

By E. W. Engelmann

A NEW and interesting type of drier has been developed and operated at the Magna plant of the Utah Copper Co. for the past year for the drying of a filtered concentrate in the molybdenum recovery plant of this company. The several units installed have ranged from 12 to 30 in. in width, and from 14 to 30 ft. long. Their economy was immediately apparent after the first one was installed. The machine is not only low in capital cost, but has proved efficient for the drying of fine concentrate at low operating cost. The Utah vibrating drier consists of a steel conveyor trough supported on flexible reeds from a structural steel foundation anchored in concrete. The steel pan, which is also the drying surface, is vibrated by a heavy Utah electromagnetic vibrator fastened either to the head or discharge end of the pan. The vibration thus obtained agitates the material and causes it to be conveyed over the heated surface.

Jan 1, 1938

By Edward H. Robie

In late November and early December a considerable portion of our time was devoted to obtaining a business manager for Institute headquarters. The advisability of creating such a position was suggested in 1949 in the report of the Johnson committee. In that year, however, the Institute had a deficit of $72,000 so every effort was made to minimize expense. At that time most of the duties that normally would be assumed by a business manager were given to Newell Appleton who became office manager, convention manager, purchasing agent, and assistant to the secretary. So many responsibilities were his that he could not devote the necessary time to all of the many things that needed attention. H. H. Vasoll, representing a firm that made a study of Institute head office procedures early last fall, made a recommendation that "a business manager and controller from outside the present organization" be obtained, who would supervise the work of accounting, addressograph, purchasing, book and journal orders, filing, and mailing depts. He further recommended that Mr. Appleton be made administrative secretary, in which position he would act as head of an "Institute Activities Dept." He would devote his time to convention planning, meeting arrangements, travel accommodations, membership control and promotion, and public relations, and would assist the Secretary on special problems. Thus, Mr. Appleton retains some of his former responsibilities and will take more of the load off our shoulders in the conduct of affairs at Institute headquarters. The rest of his former work will be in the province of the newly created "Business Office Dept." Peter J. Apol is the man finally selected for the post of business manager. He is a young man of 32, a native Michigander and a graduate of the University of Michigan where he received a B.S. degree in business administration in 1940. He then spent three years in the Navy and has the rank of Lieutenant in the U. S. Naval Reserve. Three more years were spent in the U. S. Maritime Service as chief purser, and another year as chief paymaster for the Pope & Talbot Steamship Co. The past four years have been spent as head of the Greenland Construction Co., Greenland, N. H., chiefly engaged in building construction. Mr. Apol will endeavor to increase the efficiency of Institute headquarters operations and remove all possible causes for complaints of individual members. He will coordinate as seems advisable the work of various departments and install such modern business office machinery as seems applicable to our needs.

Jan 1, 1952

Temperatures in the Open-hearth Furnace. By Robert B. Sosman. (Metals Tech. Aug. 1948, T.P. 2435) Steelmaking Direct Oxidation in the Basic Open Hearth Process. By E. R. Hughes and F. G. Norris. (Metals Tech., June 1948, T.P. 2380) With discussion Operation of Oxygen-enriched Open-hearth Furnaces. By J. S. Marsh. (Metals Tech., Aug. 1948, T. P. 2416) With discussion Role of Thermochemical Factors in Basic Open Hearth Production Rate. By T. E. Brower and B. M. Larsen. (Metals Tech., Oct. 1948, T.P. 2451) Structure, Segregation and Solidihcation of Semikilled Steel Ingots. By M. Tenenbaum. (Metals Tech., Sept. 1947, T.P. 2273) With discussion The Origin of Silicate Inclusions in Basic Electric-arc-furnace Steel of Higher Carbon Contents. By Axel Hultgren. (Metals Tech., Aug. 1948, T.P. 2418) A Method for Determining the Origin of Surface Defects in Rolled Steel Products. By C. L. Meyette and V. L. Elliott. (Metals Terh., June 1948, T.P. 2368) With discussion Gases in Steel The Sampling and Analysis of Steel for Hydrogen. By G. Derge, W. Peifer and J. H. Richards. (Metals Tech., June 1948, T.P. 2362) With discussion Apparatus for the Hot-extraction Analysis for Hydrogen in Steel. By C E. Sims and G. .I. Moore. (Metals Tech., June 1948, T.P. 2369) With discussion A Quantitative Experimental Investigation of the Hydrogen and Nitrogen Contents of Steel during Commercial Melting. By C. E. Sims, G. A. Moore and D. W. Williams. (Metals Tech., Feb. 1948, T.P. 2347) With discussion The Effect of Hydrogen on the Ductility of Cast Steels. By C. E. Sims, G. A. Moore and D. W. Williams. (Metals Tech., Sept. 1948, T.P. 2454) Sulphur in Ironmaking Kinetics of the Transfer of Sulphur across a Slag-metal Interface. By Lo-ching Chang and K. Goldman. (Metals Tech., June 1948, T.P. 2367) With discussion Some Correlations between Variables Affecting Sulphur in Blast Furnace Iron. By T. E. Brower and B. M. Larsen. (Metals Tech., Sept. 1948, T.P. 2465) Tracer Study of Sulphur in the Coke Oven. By S. E. Eaton, R. W. Hyde and 11. S. Old. (Metals Tech., Sept. 1948, T.P. 2453) Transformation of Austenite Anisothermal Formation of Bainite and Proeutectoid Constituents in Steels. By Leonard D. Jaffe. (Metals Tech., Dec. 1947, T.P. 2290) With discussion Austenite Transformation Above and Within the Martensite Range. By R. T. Howard, Jr. and M. Cohen. (Metals Tech., Oct. 1947, T.P. 2283) With discussion

Jan 1, 1949

By M. R. J. Wyllie

The relationship between the electromotive force (E.M.F.) across a shale barrier and the concentrations of sodium chloride solutions on either side has been investigated. It is shown that the action of a shale barrier is analogous to a glass membrane separating two acid solutions of different hydrogen ion concentrations. The shale behaves as a sodium electrode and is responsive to the activities of the sodium ions in the two solutions in such a way that the potential can be calculated by means of the Nernst equation. This conclusion is confirmed by laboratory experiments. In a borehole the total E.M.F. of a shale cell is the algebraic sum of the ~otential across the shale and a boundary potential. The relationship between total E.M.F. and the resistivity ratio of two sodium chloride solutions is indicated for a number of formation temperatures. The E.M.F. thus predicted is then compared with the .elf potential read from an electric log and good agreement is demonstrated. Based on both the self potential and resistivity curves of the electrical log. a method is given for calculating connate water content in a bed having in-tergranular porosity and containing both connate water and hydrocarbons. INTRODUCTION The first paper on electrical well logging by C. and M. Schlumberger and E. G. Leonardon in 1934' attributed the self potential curve principally to streaming potentials, i.e. to electroki-netic effects. Almost immediately great difficulties were encountered in reconciling many of the curves they obtained with this interpretation. and a ~econd paper' by the same authors soon appeared. In this second paper self potentials were attributed to the combined effects of streaming potentials and electrochemical potentials, the electrochemical potential being considered the result mainly of the interaction of fluids of differing salt concentrations, i.e. a boundary potential, and partly of potentials set up at the faces of impermeable materials. Some experiments involving a gray clay for the impermeable material were quated. The Schlumbergers and Leonardon deduced from the equation for a simple boundary ~otential that the electrochemical potential, as opposed to the electrokinetic potential, could be expressed in the form E=Klog- .......1 pe where K is a constant, pm the mud resistivity. p, the resistivity of the connate water in a porous bed. However, no general expression for the constant K was obtained. Although the literature between 1934 and 1943 contains a number of quotations of their results, the valuable work of the Schlumbergers and Leonardon was not extended so that the electrochemical potential has been generally attributed wholly to boundary potentials between the mud in the borehole and the connate waters in porous formations. Unfortunately, however, the fundamental premise of all these papers, that a boundary potential can give rise to current flow in a borehole, is thermodynamically untenable. As will be shown. the fact that the electrochemical potential can be fairly accurately express as E = K log pm/pc, a form in which a boundary potential may also be written, is partly fortuitous. The boundary potential is indeed an integral part of the expression for the electrochemical potential in a horehole, but in magnitude it represents only about 20% of the total potential. In 1943 an important step in the elucidation of electrochemical potentials was made by Mounce and Rust3 who showed that if a wall of shale separated two compartments which contained saline solutions of different concentrations, and if the two solutions were themselves brought into contact in the pores of a porous inert membrane (such as unglazed porcelain) a current flowed through the shale and saline solutions. The direction of positive current was from the shale into the more dilute solution. The paper of Mounce and Rust, while repeating some of the observations of the Schlumbergers and Leonardon, seems to be the first to show that the shale was the seat of a genuine electrochemical effect capable of causing current flow. In the same paper Mounce and Rust pointed out the similarity between the fundamental conditions of their experiment and the conditions which existed when a bed of shale in the ground was simultaneously in contact with a porous sand containing saline connate water and mud fluid of salinity different from that of the water in the sand. Since it is now generally recognized that the S.P. curve measures ohmic potential changes in the mud fluid in the well bore resulting from changes in current flow, it is apparent that currents having their origin in the electrochemical interaction of mud filtrate and connate waters with shale beds are a very important portion of the total S.P. The work of Mounce and Rusta and others appears to indicate that, in general, the electrochemical portion of a particular kick on a S.P. curve far exceeds any electrokinetic potentials resulting either from streaming potentials or Dorn effects. The Dorn effect, or sedimentation potential. arises when small particles are allowed to fall through certain fluids under the influence of gravity. a difference of potential being observe? between two electrodes placed at different levels in the stream of falling particles. The Dorn effect is unlikely to affect seriously the S.P. curve as now measured. A successful analysis of the electrochemical aspects of the S.P. log should

Jan 1, 1949

By M. R. J. Wyllie

The relationship between the electromotive force (E.M.F.) across a shale barrier and the concentrations of sodium chloride solutions on either side has been investigated. It is shown that the action of a shale barrier is analogous to a glass membrane separating two acid solutions of different hydrogen ion concentrations. The shale behaves as a sodium electrode and is responsive to the activities of the sodium ions in the two solutions in such a way that the potential can be calculated by means of the Nernst equation. This conclusion is confirmed by laboratory experiments. In a borehole the total E.M.F. of a shale cell is the algebraic sum of the ~otential across the shale and a boundary potential. The relationship between total E.M.F. and the resistivity ratio of two sodium chloride solutions is indicated for a number of formation temperatures. The E.M.F. thus predicted is then compared with the .elf potential read from an electric log and good agreement is demonstrated. Based on both the self potential and resistivity curves of the electrical log. a method is given for calculating connate water content in a bed having in-tergranular porosity and containing both connate water and hydrocarbons. INTRODUCTION The first paper on electrical well logging by C. and M. Schlumberger and E. G. Leonardon in 1934' attributed the self potential curve principally to streaming potentials, i.e. to electroki-netic effects. Almost immediately great difficulties were encountered in reconciling many of the curves they obtained with this interpretation. and a ~econd paper' by the same authors soon appeared. In this second paper self potentials were attributed to the combined effects of streaming potentials and electrochemical potentials, the electrochemical potential being considered the result mainly of the interaction of fluids of differing salt concentrations, i.e. a boundary potential, and partly of potentials set up at the faces of impermeable materials. Some experiments involving a gray clay for the impermeable material were quated. The Schlumbergers and Leonardon deduced from the equation for a simple boundary ~otential that the electrochemical potential, as opposed to the electrokinetic potential, could be expressed in the form E=Klog- .......1 pe where K is a constant, pm the mud resistivity. p, the resistivity of the connate water in a porous bed. However, no general expression for the constant K was obtained. Although the literature between 1934 and 1943 contains a number of quotations of their results, the valuable work of the Schlumbergers and Leonardon was not extended so that the electrochemical potential has been generally attributed wholly to boundary potentials between the mud in the borehole and the connate waters in porous formations. Unfortunately, however, the fundamental premise of all these papers, that a boundary potential can give rise to current flow in a borehole, is thermodynamically untenable. As will be shown. the fact that the electrochemical potential can be fairly accurately express as E = K log pm/pc, a form in which a boundary potential may also be written, is partly fortuitous. The boundary potential is indeed an integral part of the expression for the electrochemical potential in a horehole, but in magnitude it represents only about 20% of the total potential. In 1943 an important step in the elucidation of electrochemical potentials was made by Mounce and Rust3 who showed that if a wall of shale separated two compartments which contained saline solutions of different concentrations, and if the two solutions were themselves brought into contact in the pores of a porous inert membrane (such as unglazed porcelain) a current flowed through the shale and saline solutions. The direction of positive current was from the shale into the more dilute solution. The paper of Mounce and Rust, while repeating some of the observations of the Schlumbergers and Leonardon, seems to be the first to show that the shale was the seat of a genuine electrochemical effect capable of causing current flow. In the same paper Mounce and Rust pointed out the similarity between the fundamental conditions of their experiment and the conditions which existed when a bed of shale in the ground was simultaneously in contact with a porous sand containing saline connate water and mud fluid of salinity different from that of the water in the sand. Since it is now generally recognized that the S.P. curve measures ohmic potential changes in the mud fluid in the well bore resulting from changes in current flow, it is apparent that currents having their origin in the electrochemical interaction of mud filtrate and connate waters with shale beds are a very important portion of the total S.P. The work of Mounce and Rusta and others appears to indicate that, in general, the electrochemical portion of a particular kick on a S.P. curve far exceeds any electrokinetic potentials resulting either from streaming potentials or Dorn effects. The Dorn effect, or sedimentation potential. arises when small particles are allowed to fall through certain fluids under the influence of gravity. a difference of potential being observe? between two electrodes placed at different levels in the stream of falling particles. The Dorn effect is unlikely to affect seriously the S.P. curve as now measured. A successful analysis of the electrochemical aspects of the S.P. log should

Jan 1, 1949

By Richard Ageton

SALT bodies in the form of rolls, horses (sometimes called horsebacks), folds, wants and pinches1 have been encountered while driving entries and mining out rooms during the development of the potash mines in New Mexico. Superficially these sporadic salt occurrences appear to be much alike, but closer examination reveals individual characteristics, and after four years of observation it seems possible to divide them into three general groups that may tentatively be called "depositional," "erosional," and "structural." The data collected are not yet sufficient to permit forecasts of their probable location, so that the annoyance of having to mine salt instead of potash could be avoided or lessened. However, the information so far available appears to throw some light on the occurrence of the sylvinite2 bed now being mined, and it is as a progress report that the writer presents the results of his observations. The mines of the United States Potash Co. and the Potash Company of America are about 20 miles northeast of Carlsbad, in Eddy County, N. M. They are on the southwestern flank of the Permian salt basin, which underlies western Texas, Oklahoma and Kansas, south-central Nebraska, southeastern Colorado and eastern New Mexico. The cuttings from many oil wells and the cores from the potash tests drilled in this basin indicate that this salt series approached its greatest thick-ness (about 4000 ft.) in the southeastern part of New Mexico and the adjoining portions of Texas, and that the most advanced stages of

Jan 1, 1936

By Richard Ageton

SALT bodies in the form of rolls, horses (sometimes called horsebacks), folds, wants and pinches1 have been encountered while driving entries and mining out rooms during the development of the potash mines in New Mexico. Superficially these sporadic salt occurrences appear to be much alike, but closer examination reveals individual characteristics, and after four years of observation it seems possible to divide them into three general groups that may tentatively be called "depositional," "erosional," and "structural." The data collected are not yet sufficient to permit forecasts of their probable location, so that the annoyance of having to mine salt instead of potash could be avoided or lessened. However, the information so far available appears to throw some light on the occurrence of the sylvinite2 bed now being mined, and it is as a progress report that the writer presents the results of his observations. The mines of the United States Potash Co. and the Potash Company of America are about 20 miles northeast of Carlsbad, in Eddy County, N. M. They are on the southwestern flank of the Permian salt basin, which underlies western Texas, Oklahoma and Kansas, south-central Nebraska, southeastern Colorado and eastern New Mexico. The cuttings from many oil wells and the cores from the potash tests drilled in this basin indicate that this salt series approached its greatest thick-ness (about 4000 ft.) in the southeastern part of New Mexico and the adjoining portions of Texas, and that the most advanced stages of

Jan 1, 1936

By Richard V. Ageton

Salt bodies in the form of rolls, horses (sometimes called horsebacks), folds, wants and pinches1 have been encountered while driving entries and mining out rooms during the development of the potash mines in New Mexico. Superficially these sporadic salt occurrences appear to be much alike, but closer examination reveals individual characteristics, and after four years of observation it seems possible to divide them into three general groups that may tentatively be called "depositional," "erosional," and "structural." The data collected are not yet sufficient to permit forecasts of their probable location, so that the annoyance of having to mine salt instead of potash could be avoided or lessened. However, the information so far available appears to throw some light on the occurrence of the sylvite2 bed now being mined, and it is as a progress report that the writer presents the results of his observations. The mines of the United States Potash Co. and the Potash Company of America are about 20 miles northeast of Carlsbad, in Eddy County, N. M. They are on the southwestern flank of the Permian salt basin, which underlies western Texas, Oklahoma and Kansas, south-central Nebraska, southeastern Colorado and eastern New Mexico. The cuttings from many oil wells and the cores from the potash tests drilled in this basin indicate that this salt series approached its greatest thickness (about 4000 ft.) in the southeastern part of New Mexico and the adjoining portions of Texas, and that the most advanced stages of

Jan 1, 1938

By Richard V. Ageton

Salt bodies in the form of rolls, horses (sometimes called horsebacks), folds, wants and pinches1 have been encountered while driving entries and mining out rooms during the development of the potash mines in New Mexico. Superficially these sporadic salt occurrences appear to be much alike, but closer examination reveals individual characteristics, and after four years of observation it seems possible to divide them into three general groups that may tentatively be called "depositional," "erosional," and "structural." The data collected are not yet sufficient to permit forecasts of their probable location, so that the annoyance of having to mine salt instead of potash could be avoided or lessened. However, the information so far available appears to throw some light on the occurrence of the sylvite2 bed now being mined, and it is as a progress report that the writer presents the results of his observations. The mines of the United States Potash Co. and the Potash Company of America are about 20 miles northeast of Carlsbad, in Eddy County, N. M. They are on the southwestern flank of the Permian salt basin, which underlies western Texas, Oklahoma and Kansas, south-central Nebraska, southeastern Colorado and eastern New Mexico. The cuttings from many oil wells and the cores from the potash tests drilled in this basin indicate that this salt series approached its greatest thickness (about 4000 ft.) in the southeastern part of New Mexico and the adjoining portions of Texas, and that the most advanced stages of

Jan 1, 1938

By Lawrence Addicks

One of the properties of copper, which has done much to give it its present prominent place among the useful metals, is its electrical conductivity,—a property which has now become the chief criterion of the value of the commerical product. In pursuance of that distinctively American principle that, " the best is none too good," metal of the highest conductivity is usually called for even when such extreme purity is of no advantage ; for instance, in the making of brass and other alloys. The average brass-founder feels nervous unless his copper is so very pure that it shows a conductivity of 99 or 100 per cent., while the character of the zinc used is usually overlooked in hi s anxiety. Electrolytic refining has made it possible to produce copper

Jan 1, 1906

By C. Perez-Rosales

A simplified method for evaluating specific surface of porous media is described. The theory takes as its point of departure a previous statistical method. Due to its simplicity, it is considered that the proposed method has certain advantages over methods currently used. By making some simplifications, the procedure for estimating specific surface is reduced to superposing, on an enlarged reproduction of a section of the sample to be analyzed, an evenly spaced grid and counting the number of intersections of the grid lines with the perimeter of pores. An indirect test of the theory is presented and the advantages of the method are discussed. INTRODUCTION The specific surface of a porous medium, defined as the surface area of the pores per unit bulk volume, is an important parameter with regard to flow of fluids through porous materials. In particular, it has long been recognized that specific surface is closely related to permeability. Since the internal surface of any porous material is extremely complex, the measurement of specific surface can only be accomplished by indirect means. It is considered that the best method' in current use for determining specific surface is the statistical method of Chalkley, Cornfield and Parka who originally applied it for estimating volume-surface ratios of morphologic components, such as cells or nuclei. This method will be outlined later. A method which has been used extensively in determining specific surface is based on the adsorption of a vapor by the internal surface of porous media. However, this method does not yield the surface pertinent to fluid flow, since it includes the tiny molecular interstices which do not influence the permeability of the porous material.' This method has been employed by Brooks and Purcell measure internal surface area of sedimentary rocks. The Kozeny equation, which relates the specific surface to the permeability of a porous medium, has found wide use in determination of specific surface. However, the KOzeny equation is not strictly correct. Large discrepancies have been found between theory and experiments.' Consequently. the specific surface estimated by this method is subject to serious uncertainties. Finally, there are other methods for specific surface measurements which are based upon a variety of physical and chemical properties: the heat conduction by a gas, ionic adsorption phenomena and direct chemical reactions of the surface with other substances. This paper describes a simplified statistical method for determining specific surface of porous materials. It is considered that, due to its simplicity, it has certain advantages over the methods presently used. For its validity, it is required that the porous structure of the material under study be of a spatially random nature. This is not a serious limitation since the naturally occurring porous media have this characteristic. THEORY The method proposed in this paper takes as its point of departure the interesting result obtained by Chalkley et al The method shows that if a line of length r is dropped repeatedly at random over a section of a porous medium, and counts are made of the number of times the two end points fall within pore areas (denoted by h for "hits") and the number of times the line intersects the perimeter of pores (denoted by c for "cuts"), then in a very large number of throws where S is the internal surface of the sample (surface of pores) and V, the volume of the pores (Fig. 1). Since the specific surface S, and the porosity 4 are given, respectively, by S. = Sl V, and 4 = V,l V,, where V, is the total volume of the sample, it follows from Eq. 1

By P. S. Roller

P. S. ROLLER,*College Park, Md.-The author introduces the idea of a grind limit, or lower size limit of the particles formed directly by grinding, and this is stipulated to be 0.70 micron. I wonder where all the particles come from that lie between the resolving power of the microscope and 0.7 micron, which are seen under a microscope in examining a sample of grind? There is also introduced the idea of excess fines; this is all right in itself but the author's quantitative definition seems to be virtually impossible to justify, and, moreover, is obscure. Just why E, the excess fines, should he defined as the distance between an F line and a y line is hard to follow, and just where the distance should be measured does not appear to be stated, as it should be since the F and y lines intersect and the distance between will depend upon where that distance is measured. The basis of the presentation is the relation of log weight against log size that was "discovered" by Schuhmann. While this relation is implied to fit, the only evidence that I can see is a slightly irregular line in Fig. x between 2 per cent and 18 per cent by weight and then a precipitous drop at 18 per cent away from any sort of straight line. Some of the conclusions are rather startling. It is stated that E, the excess fines, remains constant for all the comminution products of any particular material, except that it may decrease for some coarse crusher products. No reason is given for this assertion. One would, on the contrary, expect that excess fines, if such a concept is permissible, would generally vary with different conditions instead of being constant. Again, "as much net energy is required to reduce a ton of quartz to particles of the grind-limit diameter (namely, of course, 0.7 micron) by grinding as is required to melt the quartz." This would require many data to prove, but no proof is given; any consideration would reveal the impossibility of such a result. Still further, ore samples "ground to widely different sizes, and with different circulating loads and different size distributions or product, show the same production of new surface area per revolution of the mill, when this grind limit is used." This statement is confuted by ordinary experience, which teaches that grinding efficiency varies generally with the condition of material. For example, the cushioning effect of fines is widely accepted, while the inefficiency of a ball mill when the feed is too coarse is also well known. R. SCHUHMANN, JR.," Cambridge, Mass. Contrary to Mr. Bond's stand, there is a great deal of miscellaneous experimental evidence that comminution does not stop at around 0.7 micron, nor does it cease consuming energy at that point. Comminution is in fact recognized as an important method of producing colloids., Mechanical comminution methods were used by von Weimarn6 to produce colloidal dispersions of a variety of solids, including the minerals chalcocite, galena, hematite, stibnite. Utzino7 gives average particle sizes ranging from 0.02 to 0.09 micron for colloids produced by mechanical comminution of several crystalline solids. Andreasen and Berg' have ground

Jan 1, 1941

By P. S. Roller

P. S. ROLLER,* College Park, Md.-The author introduces the idea of a grind limit, or lower size limit of the particles formed directly by grinding, and this is stipulated to be 0.70 micron. I wonder where all the particles come from that lie between the resolving power of the microscope and 0.7 micron, which are seen under a microscope in examining a sample of grind? There is also introduced the idea of excess fines; this is all right in itself but the author's quantitative definition seems to be virtually impossible to justify, and, moreover, is obscure. Just why E, the excess fines, should be defined as the distance between an F line and a y line is hard to follow, and just where the distance should be measured does not appear to be stated, as it should be since the F and y lines intersect and the distance between will depend upon where that distance is measured. The basis of the presentation is the relation of log weight against log size that was "discovered" by Schuhmann. While this relation is implied to fit, the only evidence that I can see is a slightly irregular line in Fig. I between 2 per cent and 18 per cent by weight and then a precipitous drop at 18 per cent away from any sort of straight line. Some of the conclusions are rather startling, It is stated that E, the excess fines, remains constant for all the comminution products of any particular material, except that it may decrease for some coarse crusher products. No reason is given for this assertion. One would, on the contrary, expect that excess fines, if such a concept is permissible, would generally vary with different conditions instead of being constant. Again, "as much net energy is required to reduce a ton of quartz to particles of the grind-limit diameter (namely, of course, 0.7 micron) by grinding as is required to melt the quartz." This would require many data to prove, but no proof is given; any consideration would reveal the impossibility of such a result. Still further, ore samples "ground to widely different sizes, and with different circulating loads and different size distributions or product, show the same production of new surface area per revolution of the mill, when this grind limit is used." This statement is confuted by ordinary experience, which teaches that grinding efficiency varies generally with the condition of material. For example, the cushioning effect of fines is widely accepted, while the inefficiency of a ball mill when the feed is too coarse is also well known. R. SCHUHMANN, JR.,* Cambridge, Mass.-Contrary to Mr. Bond's stand, there is a great deal of miscellaneous experimental evidence that comminution does not stop at around 0.7 micron, nor does it cease consuming energy at that point. Comminution is in fact recognized as an important method of producing colloids.5 Mechanical comminution methods were used by von Weimarn6 to produce colloidal dispersions of a variety of solids, including the minerals chalcocite, galena, hematite, stibnite. Utzino7 gives average particle sizes ranging from 0.02 to 0.09 micron for colloids produced by mechanical comminution of several crystal-line solids. Andreasen and Berg8 have ground

Jan 1, 1941

By Orson Shepard

THE leaching method that was first widely used with the cyanide process consisted of percolation leaching of crushed ore in vats or leaching tanks. It was frequently necessary to separate the sand for cyanide treatment and discard the slimes, because only granular material allows the necessary amount of solution to percolate through it in a reasonable time. Later a slime process consisting of agitation followed by thick-ening and filtration was developed, and is extensively used to the pres-ent day. Even though the agitation-leaching slime process is considered satis-factory, the cost of plant and of operation are both greater than for a percolation-leaching plant of equal capacity. This situation has been recognized in the hydrometallurgical treatment of copper-bearing slimes; and a considerable amount of j work has been done at the Southwest Experiment Station of the U. S. Bureau of Mines in an effort to develop a percolation method of treating slimes. Experimental work on the copper-leaching problem was started by H. E. Keyes1, and later tests were made by J. D. Sullivan and A. P. Towne2. The Bureau of Mines work resulted in the development of a process by which slimes were moisture-agglomerated with sand and crushed ore, to form a permeable mass through which solution could be trickled without breaking clown the glomerules. The agglomeration trickle-leaching method was devel-oped on a small scale and finally tried out in a 12-ton vat. Successful results were obtained as long is the leach solution was added slowly, so that the agglomerated charge was never flooded. If the leach solu-tion flooded the charge, the glomerules broke down and, the charge became impervious. There are two important difficulties in the application of the agglom-eration trickle-leaching-method to the cyanide process for gold and silver ores:

Jan 1, 1937