Search Documents

PRESIDENT HERBERT HOOVER, STANFORD UNIVERSITY; CAL. PAST PRESIDENTS SIDNEY J. JENNINGS NEW YORK, N. Y. HORACE V. WINCHELL MINNEAPOLIS, MINN. FIRST VICE-PRESIDENT EDWIN LUDLOW, NEW YORK, N. Y. TREASURER GEORGE D. BARRON NEW YORK, N. Y.

Jan 1, 1923

AIMS 1953 DIRECTORY SUPPLEMENT OFFICERS AND DIRECTORS 1953 President and Director ANDREW FLETCHER (2) New York City Past President and Director MICHAEL L. HAIDER (2) New York City President-elect and Director LEO F. REINARTZ (3) Middletown, Ohio Vice-Presidents and Directors 0. B. J. Fraser (2), New York City J. L. Gillson (1), Wilmington, Del. A. B. Kinzel (3), New York J. B. Morrow, (2) Pittsburgh, Pa. L. E. Elkins (3), Tulsa, Okla. * T. B. Counselman, Stamford, Conn.

Jan 1, 1953

By Arthur H. Wilson

INTRODUCTION The stratified deposits of the coal measures are strongly laminated and exhibit a high degree of anisotropy. The stronger rocks in the sequence possess joints and shear planes, the coal itself has a closely spaced cleat pattern, and the softer rocks are capable of flowage. To calculate the general distribution of stress in such a medium by analytical means based on the theories of elasticity is difficult, and has not yet been satisfactorily achieved. Nevertheless, some estimate is required to aid the design of supporting pillars and permit the correct siting of main roadways. This is important when laying out districts for longwall extraction, particularly if the results of previous experience are not available in the area to be exploited. Although elastic stress analyses, including finite element analysis, may not be very appropriate, the basic equilibrium conditions will apply. These, combined with logical deductions based on observed fact, can be used to give appropriate solutions which experience has shown to be capable of giving acceptable results in the design of pillars associated with longwall workings. Constancy of cover load is one of the fundamental equilibrium conditions. When mining below ground, the cover is not removed, therefore the average vertical load after mining must equal the initial cover load. If mining produces a local decrease in load in any particular area, it must be balanced by an equivalent increase in load nearby. Bending moments in the strata above are capable of compensating for the turning moments which this redistribution of load may produce, and the existence of a "rear abutment", much discussed between 1950 and 1960, is not an essential equilibrium requirement. If the distribution of vertical stress is plotted three-dimensionally, then the load on any small element of area 6S will be o.6S, where o is the average stress. This also represents the volume of the "stress envelope" which lies above 6s. By making the individual areas very small and summing together, it is possible to show that the total load on any particular area can be found by calculating the volume of the stress distribution envelope which lies above it. A similar consideration applies to the stress distribution in a two-dimensional situation. If the stress distribution curve is drawn, then the area below any portion will represent the load per unit depth of section. For example, Figure 1 represents the possible stress distribution across a caved waste and associated ribside. If AW is the load deficiency [ ] These loads must balance, therefore area AW = AS, and if one can be deduced, the other will then be known. Attempts have been made to measure stress distributions in the ribside and in the waste. Stress meters in soft rocks such as the coal measures have not proved very effective. Those based on the measurement of strain have experienced difficulty in strata capable of flowage, high modulus stress meters suffer from cross sensitivity, and overcoming to obtain absolute stress is almost impossible. Load measuring instruments left in the waste have also proved largely ineffective, mainly as a result of the difficulties of protecting the leads in a caving environment. Certain logical deductions, however, can be made about the conditions in the waste. CONDITIONS IN THE WASTE Over the area of the waste the surface trough which develops is remarkably consistent, despite the geological variations which occur from coalfield to coalfield. In Britain, an accuracy of 210% is claimed for subsidence prediction based on width of extraction and depth of cover (National Coal Board, 1975). The subsidence in the USA is more variable (Adamek and Jeran, 1981), particularly with respect to the point of inflexion, but the same general pattern occurs. At the shallower depths the somewhat harder roof strata involved in the caving in the USA may suffer less compaction, giving reduced values of subsidence. Subsidence at intermediate horizons below the surface

Jan 1, 1982

By William E. Hubbard

During the last decade the known reserves of petroleum in the United States have increased from about five billion to over thirteen billion barrels. From the standpoint of public welfare the existence of these known reserves presents an undeniably favorable picture, but viewed from the position of many a harassed operator the blessing has not always been considered an unmixed one. Along with this increase in excess reserves, curtailment of production has come into being as a matter of necessity and the principle of proration as a matter of equity. As a practical matter it has been considered necessary to curtail the production of old wells as well as that of new wells in a pool. The right of new pools to produce has been recognized, and the allowable for them has come partly from increased market demand and largely from the allowables already enjoyed by the developed pools. The natural result—a downward trend in daily per-well allowables—has been especially felt by Texas operators. This trend may be illustrated by Table 1, which comprises the five active areas in Texas, and from which may be noted the following: 1. The average daily allowable per well has decreased about 53 per cent in three years. 2. Of the 184,000-bbl. increase in total allowable for the five areas, 29,000 bbl. came from the increase in state demand and 165,000 from the combined allowables of the remaining pools in the state.

Jan 1, 1937

ALEXANDER, JOHN S, M,'74-6,'81-3 ASHBURNER, C A, M, '85-7 ASMUS, GEORGE, Dl, '78-80 BACON, D H , M, '00-2 BAYLES, JAMES C , M,'80-2,'91-3 P, '84-5, V,'88-9 BIRKINBINE, JOHN, M, '83-5, V, 'S7-J, P, '91-2 BLAIR, THOMAS S , M, '74-43 BLAKE, WILLIAM P , V,'71-4,'76-7,'05-6 BLANDY, JOHN F, V,'71-3,'78-9 BLOW, A A, C, '05-7 BOWIE, A J , JR, V,'93-4 BRAMWELL, J H , A1, '89-91 BROOKS, THOS B , M, '72 BRUNTON, D W , V, 97-8 BUCK, STUART M , M, '83-5 BURDEN, JAMES A, V,'80-1 BURNHAM, WILLIAM, M, '82-4. CAMPBELL, H H, M, '93-5 CHAMBERLAIN, H S , V, '96-7 CHANNING, J PARKE, V,'08 CHRISTY, S B , V. '91-2, '07-8 CHURCH, JOHN A, M, '79-8l,'94-6, V, '07-8 COGSWELL, W B, V, '74-5,'86-7

Jan 1, 1910

ALEXANDER, JOHN S, M,'74-6,'81-3 *ASHBURNER, C A, M, '85-7 ASMUS, GEORGE, Dl, '78-80 BACON, D H , M, '00-2 BAYLES, JAMES C , M,'80-2,'91-3 P, '84-5, V,'88-9 BIRKINBINE, JOHN, M, '83-5, V, 'S7-J, P, '91-2 BLAIR, THOMAS S , M, '74-43 BLAKE, WILLIAM P , V,'71-4,'76-7,'05-6 *BLANDY, JOHN F, V,'71-3,'78-9 BLOW, A A, C, '05-7 BOWIE, A J , JR, V,'93-4 *BRAMWELL, J H , A1, '89-91 BROOKS, THOS B , M, '72 BRUNTON, D W , V, 97-8 BUCK, STUART M , M, '83-5 *BURDEN, JAMES A, V,'80-1 BURNHAM, WILLIAM, M, '82-4. CAMPBELL, H H, M, '93-5 CHAMBERLAIN, H S , V, '96-7 CHANNING, J PARKE, V,'08 CHRISTY, S B , V. '91-2, '07-8 CHURCH, JOHN A, M, '79-8l,'94-6, V, '07-8 COGSWELL, W B, V, '74-5,'86-7

Jan 1, 1910

By R. W. Cahn, C. D. Graham

Two predictions of the oriented growth theory of recrystallization textures have been tested by measuring the orientation dependence of the rate of growth of a single grain into a strained single crystal of aluminum, and determining the orientations of artificially and spontaneously nucleated grains growing preferentially into strained aluminum single crystals. Growth rates are found to be insensitive to orientation, except that new grains with orientations similar to the matrix or to a twin of the matrix have very low mobilities. Similarly, new grains growing preferentially into a strained crystal have random orientations, except that orientations near that of the matrix or its twins are avoided. The predictions of oriented growth theory are thus not confirmed. BASICALLY, the oriented growth theory of re-crystallization textures1 rests on the assumption that the rate of growth of a recrystallizing grain depends strongly on the orientation of the growing grain relative to the strained matrix into which it grows. In particular, the theory holds that in face-centered-cubic metals the orientation which corresponds to maximum growth rate is one in which the growing grain and the matrix are related by a rotation about a common <111> direction. The amount of rotation, as derived from several kinds of experiments,2-1 has been assigned various values, generally in the range between 20" and 40". (A <111> rotation of 60" is a twin relationship.) The conclusion that boundary migration rates depend strongly on orientation is based almost entirely on indirect evidence; there have been very few direct measurements of boundary migration rates as a function of orientation.* " The present investigation was undertaken to provide such measurements, to help make possible a decision between the oriented growth and oriented nilcleation theories of recrystal-lization textures. The basic experimental program consisted of measuring the rate of growth of a single recrystal-lizing grain consuming a strained single crystal, with the orientations of both grains preselected so that the effect of orientation on growth rate could be determined. A prerequisite for such an experiment is a strained single crystal which will support the growth of a new grain but which will not spontaneously nucleate new grains on heating. That is, the crystal must support the growth of a grain nucleated artificially, but contain no recrystalliza-tion nuclei which will become active at the testing temperature. Beck was apparently the first to note that such a condition could exist," and to make use of the condition for am experiment of the type described here.&apos; The present work was actually suggested, however, by a report of Tiedema". " that an aluminum single crystal strip, oriented with a (111) plane in the plane of the strip and a < 112> direction parallel to the tensile axis, would not recrystallize after 20 pet extension even when heated almost to the melting point, provided that the strip was heavily etched before being heated. This result could not be duplicated in the present work. In fact, it was found that any crystal which deformed in multiple slip (<100>, <112> and <111> orientations) underwent spontaneous nucleation after 15 pet extension, even if etched. However, crystals which deformed in single slip, and which did not develop heavy deformation bands, could be extended 15 pet without showing spontaneous nucleation at temperatures up to 600°C. Crystals oriented within about 10o of <110> which developed heavy deformation bands could be extended 10 pet without showing spontaneous nucleation. In all cases a heavy etch was required to prevent nucleation. Etching was necessary because of the presence of an oxide layer on the crystal surface at the time of straining, which leads to preferential nucleation at the surface.&apos;&apos; Grain Growth Rates Experimental Procedure and Results—Aluminum strips of 99.6 pet purity (principal impurities 0.19 pet Fe and 0.12 pet Si), 1 mm by 1 cm in cross section, were grown into single crystals of controlled orientation by the strain-anneal method of Fuji-wara.&apos;"&apos; " A sharp temperature gradient was maintained in the strips during growth by lowering them into a salt bath controlled at 650°C. Crystal orientations were determined by the etch-pit method of Barrett and Levenson" to an accuracy of ±2O. The crystals were extended by 10 or 15 pet in a simple hand operated tensile machine. Crystal orientations were rechecked after extension, and were found to be in agreement with the orientations predicted by the formula of Schmid and Boas." After extension, the grip ends of the single crystal specimen were cut off with a jeweller&apos;s saw, and the crystal heavily etched (at least 20 pet wt loss) in hot 10 pet Na or KOH solution. A region of severe local deformation was then introduced at one corner of the strip, usually by cutting off the corner with shears. Heating this end of the strip caused a large number of new grains to nucleate at the sheared edge. One of these grains grew to occupy the full width of the strip. The appearance of the strip at

Jan 1, 1957

ANDES, lying south of Chuquicamata and north of Braden on the western slope of Chile&apos;s cordillera, can best be described as a big well-managed copper-mining enterprise without any peculiarly outstanding features. In point of copper produced, since output started in 1927, it ranks fifth among the Porphyries, being exceeded only by its two Chilean contemporaries and by Utah Copper and Morenci in the United States. Even so, there is little to distinguish it from other properties. It does not have the phenomenally rich ore (better than 2 per cent copper) that characterizes Braden; and it is not in the same class as Chuquicamata whose ore has the excellent tenor of around 1.7 per cent, nor has it Chuqui&apos;s immense tonnage of proven ore reserves and potential ore resources. One might say the operations are standard in that there are no basic or radical departures from established practice. A letter from New York supplying me with sundry pertinent facts for which I had asked, makes this comment regarding the answer to one inquiry: "omitted because it is the ordinary equipment found in any well-run mine." The substance of that remark applies generally to the other operations, plants, and facilities. One interesting fact that helps explain this situation should not be overlooked. Until the "new" Morenci in 1942, Andes was the last of the Porphyry copper mines to come into production. It did not do much pioneering because other companies had, of necessity, charted the way in many particulars. The company was organized by the Anaconda Copper interests in 1916 to take over a, group of claims held under option by William Braden who, a few years earlier, had interested

Jan 1, 1957

By George Stone

THE method of making oxide of zinc direct from the ore was invented and developed at the works of The New Jersey Zinc Co. at Newark in the middle of the last century. The process was invented by Burrows, who had not the ability, financial or technical, to work out the details necessary to make it of commercial value. This was done by Col. Wetherill, whose name is commonly attached to this process. The, grate bars used are also frequently called Wetherill grates, which is a misnomer because they were in common use for boiler firing at the time and he never claimed their invention. The invention of the process was due to the efforts of The New Jersey Zinc Co. to find a profitable means of working the ores from Franklin and Sterling Hill, N. J. These are a mixture of franklinite, willemite and zincite, containing about 20 per cent. of zinc. The first attempts were to make spelter, which were not successful, owing to the low grade of the ore and the fusibility of the residue. Failing in this, the next attempt was to make oxide in large muffles and reverberatory furnaces. This succeeded, although the cost of operation was high, the recovery low, and the quality of the product uncertain. In 1855, the new process was patented and has been in successful operation ever since. Essentially, the process is to spread a mixture of coal and ore on a body of burning coal on a perforated grate and blow an excess of air through the grate. The zinc is reduced in contact with the coal, volatilizes and burned by the excess of air in the upper part off the furnace and in the flues. It is then carried to the hag rooms by the excess air and products of combustion which are forced through the flues by fans. In its main features, the process is the same today as at the time of its invention, but the details have been so modified that it would hardly be recognized by its originators.

Jan 9, 1917

Agnico-Eagle Mines Ltd. comprises a Gold Division at Joutel, Quebec, and a Silver Division at Cobalt, Ontario. In 1979 the Silver Division milled 41,700 mt (46,000 st) of ore at a recovered grade of 139 g per mt (4.06 oz per st) for a production of 5,816 kg (187,000 oz) of silver. The 100 -year -old mining, camp of Cobalt has long been noted for its high-grade silver ores, and now seems to be on the threshold of being revived with several companies operating in the area. In 1979, the Gold Division milled at the rate of 27,200 mt per month (30,000 st) and processed 333,000 mt (367,000 st) at a grade of 6.58 g per mt (0.192 oz per st) with a mill recovery of 91.670 to produce 2,013 kg (64,700 oz) of gold. The average total cost per ton milled was $22.10 per mt ($20.05 per st) which was $3.66 per g ($1 13.90 per 0s). These figures make Agnico-Eagle one of the lowest cost producers in North America. Gold occurrence in the Joutel ore is fine-grained and contained within sulfide facies composed mainly of pyrite with minor pyrrhotite. Two underground mining methods are employed with long hole stoping accounting for about 75% of the ore mined and shrinkage stoping the remainder. Ore from underground is hoisted into a 545 mt (600 st) coarse ore bin from where it is conveyed to a 45 mt (50 st) surge bin ahead of the 10-51 Hydrocone crusher. Crushed ore is then screened to make a 13 mm (112 in.) product with the oversize being recrushed in a 7-60 Hydrocone. Mill feed is conveyed to two 900 mt (1,000 st) fine ore bins. The Hydrocones were installed as part of a new crushing plant in March of 1980 and have contributed substantially to an increase in mill capacity. Space has been left to install a third crusher in the future. The fine ore bins discharge to a 2.75 m by 3.66 m (9 ft by 12 ft) rod mill, followed by a 3. 7 m by 5.5 m (12 ft by 18 ft) ball mill in closed circuit with a Krebs 380 mm (15 in.) cyclone to produce a 7070 minus 37 micron (400 mesh) .flotation feed. This pulp is first treated in a 34 cu m (1, 200 cu ft) Maxwell flotation cell and then in an additional twelve 2.8 cu m (100 cu ft) cells. Combined flotation concentrates are reground to 9070 minus 37 microns (400 mesh) in a 1.8 m by 4.9 m (6 ft by 16 ft) ball mill in closed circuit with a single Krebs 254 mrn (10 in.) cyclone. Flotation tailings are sent to the tailings dam. Reground concentrates are then aerated with lime to a single Pachuca and thickened in a 16.75 m (55 ft) diameter thickener with the addition of diesel fuel to render any activated graphite inert to adsorption of

Jan 1, 1981

By Che, C. W. Spencer, C. A. Steidel, Yu Li

Grain boundary grooving as it occurs in a 5.5-deg simple-tilt nickel bicrystal immersed in a saturated Ni-S liquid has been studied. A 1/3 (t= time) dependence for the depth of the groove indicates that the rate -controlling meckanism for groove developvnent is volume diffusion in the liquid. The activation energy for the diffusive process is estimated at 15 kcal per mole. Using an extended form of W. W. Mullins&apos; analysis for grooving reactions, a computer is employed to fit the appropriate diffusion equation by a numerical method. From the analysis a possible method of measuring L.S. the solid-liquid interfacial tension is demonstrated. WHEN a polycrystalline solid is heated in equilibrium with a saturated fluid phase, grooves will form at the intersections of the grain boundaries and surface. The equilibrium root angle of these grooves is determined by the balance between the grain boundary and solid-fluid interfacial tensions. The grooves deepen and widen with time due to a difference in chemical potential between the flat interface and the curved interface of the groove. In this investigation solid-liquid interaction at a grain boundary is studied, with the object to determine the mechanism of grain boundary grooving in the presence of a saturated liquid. Extension of Mullin analysis then permits the estimation of the solid-liquid interfacial tension. Herring has demonstrated by dimensional analysis that the quasi-steady state change of the dimensions of a small particle during sintering is proportional flow, evaporation-condensation, volume-diffusion, and surface-diffusion mechanisms, respectively, if geometric similarity of consecutive configurations of the particles holds. Mullins has extended this analysis to grain boundary grooving. In the case of shallow grooves he solves the diffusion equations for evaporation-condensation, volume-diffusion, and surface-diffusion mechanisms, and obtains the same time dependence for any linear dimension of a groove as Herring found for the change in dimension of small particles. In Mullins&apos; analysis2&apos;3 grain boundary grooving of a bicrystal by volume diffusion in the presence of a saturated fluid phase was considered. Several assumptions were made prior to the analysis: 1) the solid-fluid interfacial tension is independent of crystallographic orientation; 2) the Gibbs-Thompson equation relating curvature and chemical potential is applicable at the solid-fluid interface; 3) the relaxation time of the diffusion field is small compared with the time for appreciable changes in the curvature of the groove, so that the diffusion is divergence-less; and 4) the groove has a small slope relative to the initial flat interface. Usually this last condition is fulfilled only for solid-gas systems. The solution of the diffusion equation under the above conditions produces a t1/3 dependence for any linear dimension of the groove in the case where volume diffusion is rate-controlling. The t1/3 dependence is valid because geometric similarity of the grooves exists for all time. EXPERIMENT In the experiment a 5.5-deg nickel bicrystal of <100> simple-tilt orientation was used.4 Grooving was studied in the presence of a saturated Ni-S liquid alloy as a function of time at 750°, 800°, 850°, and 900°C. A low-angle bicrystal was chosen for study to insure that 2L.S. > .b., where l.s.

Jan 1, 1964

By AIME AIME

ABOUT 55 attended the general session of the Nonferrous Metallurgy Committee on Wednesday afternoon. In opening the proceedings the Chairman, Frank G. Breyer, served notice of his intention to make an early start this year in securing papers for his committee. He voiced the thought that more importance should be attached to the prompt publication of data on new advances in practice; the record of technical progress should be written before the sharpness of the current image becomes blurred by the veil of time. As an illustration, Mr. Breyer declared that great strides have been made in the zinc industry during the past nine years, whereby zinc ore is converted directly to the oxide in large mechanical furnaces, yet the literature is confined to patents.

Jan 1, 1933

By G. C. Wallick

Since the appearance of the paper, "Solution of the Equations of Un-steady State Two-Phase Flow in Oil Reservoirs," by W. J. West, W. W. Garvin, and J. W. Sheldon,&apos; a two-fold investigation of this subject has been carried out. One objective of the investigation has been to deter-mine the feasibility of solving such problems 7on a medium-size com-puter such as the Datatron*, and the other objective has been to in-vestigate the application of such cal-culations to experimental and theo-retical petroleum reservoir research. In the first Datatron calculations, the fluid and rock properties published by West, et al, were used, together with the published equations describ-ing the system. Details of the formu-lation not given in the original paper are discussed in the Appendix to this note. Reference should be made to the subject paper for the complete equations and defintion of symbols. An unexpected result of this in-vestigation was the discovery that the linear solution published by West was in error. Thus, in addition to describing the Datatron solutions and to discussing certain numerical diffi-culties which will be encountered if one uses the published method of solution, the purpose of this note is to indicate the nature of this error. LINEAR FLOW Since the linear case requires a minimum amount of scaling, a fixed-decimal point Datatron program was written for the one-dimensional flow problem and an attempt was made to duplicate the solution described by West. In the case described, fluid was produced at a constant rate, Q, until such time as well pressure reached 0.04. Production was then continued at constant pressure. From the constants and curves given by West it was determined that the ini-tial constant production rate could be approximated by Q = 0.007. An ini-tial dimensionless time step ?t = 0.434 X 10 - "as used, and each suc-cessive time step was doubled until a value of = 0.444 was reached. This constant interval was then used for the remainder of the solution. In subsequent solutions, several varia-tions in the time schedule were em-ployed, including smaller time steps and slower rates of increase in the time steps. In all cases, almost identical results were obtained regardless of the time schedule employed. However, as described below, it was noted that the time schedule had some influence on the rate of convergence of the solutions. As a check on the accuracy of the solution, the cumulative production at each time step was calculated using the two methods described in the Appendix. Satisfactory agreement was observed with the differences in these two values of the order of two parts in 50,000. It should be noted that the mass balance check as described is of questionable value, particularly with regard to the well pressure and saturation. This is especially true in the radial solution where pressure and saturation values near the wellbore would make only a negligible contribution to the numer-ical integration. It is believed, how-ever, that such a comparison is ot value in determining the over-all accuracy of a solution. In comparing the Datatron solu-tion with that published by West it was discovered that in the later stages of depletion, the pressures near the well declined more rapidly in our solution than in the West solution, and that the limiting well pressure of 0.04 was reached at an earlier time than that originally reported. It thus became evident that it would be impossible to duplicate the production schedule described by West and a constant rate of production was maintained until the well pressure was equal to 0.0. A representative comparison of the results published by West with those obtained in this investigation is shown in Fig. 1, which is a plot of GOR as a function of cumulative recovery. These two curves should be in agreement until a cumulative recovery is reached which corresponds to a well pressure of 0.04 — for the Datatron solution, a recovery of approximately 5.6 per cent. Actually, a major disagreement is evident. Subsequent correspondence

Jan 1, 1958

By R. Maddi, I. R. Kramer

C. S. Roberts (Dow Chemical Co., Midland, Mich.)— In this study we have seen another example of how modern electronic instrumentation can be of great value to metallurgical research. The authors have shown much ingenuity in their experimental work. However, I wish to point out that anelasticity theory tells us that we must be cautious when we use pulse methods for measurements which are to be correlated with knowledge of static stress-strain behavior. The basic stress calibrations used by the authors depend on the use of static moduli combined with the pulsed strains. No recognition of a possible modulus defect has been indicated. The general agreement of critical resolved shear stresses may indicate that a

Jan 1, 1953

By Mark E. Emerson

INTRODUCTION A long time has passed since geologists encountered encouraging mineralization in their regional exploration program for base metals deposits. Detailed drilling during the following two field seasons served to delineate the configuration of the deposit. Various statistical techniques were employed to provide confidence levels regarding the extent of the reserves and to categorize them according to whether proved, indicated or inferred. At this juncture, it appears that the company has an orebody. Time elapsed? - three years; money spent? - $2.5 million. Much remains to be done before the orebody becomes a mine. The company urgently needs to develop new orebodies to replace its existing mines which are being depleted. It therefore has expended sizable amounts in exploration, the life blood of the company. A staff of specialists is maintained to evaluate new projects and to conduct feasibility studies. The scale of new mining projects today is beyond the resources of most mining companies. Bank financing, therefore, is often vital if the company is to survive. The following scenario describes how a company goes about evaluating mine projects and what is needed to meet lender&apos;s criteria in securing the needed financing. MINE PLANNING Now that the company engineers have taken over the project, their concern is no longer with finding ore but in developing it. An exploration shaft has been put down and a tunnel driven into the orebody to verify, on a large scale, what has been seen so far only in pencil- like drill cores. A large tonnage bulk sample is mined and shipped off to an independent metallurgical process laboratory for beneficiation testing. The budget is expended to cover engineering studies. Preliminary capical and operating costs are developed in- house and profitability studies are made based or1 assumptions concerning the markets for the main product and the indicated gold, silver, and other by-products. Time elapsed? - four years; cost to date? - $3.5-$4.5 million. The staff prepares its own pre-feasibility study. After review, the Executive Committee authorizes management to proceed with full-scale studies. The task is to make preliminary designs and to develop definitive capital and operating cost estimates. Specialized consultants will be engaged to study slope stability for the open pit and rock strength if underground recovery proves more feasible. If it is near the sea, an oceanographic report might be commissioned to see if the tailings can be disposed of off shore. Environmental impact studies are commissioned from a firm familiar with government requirements and regulations in this important area. The company subscribes for an expensive multi-client study of the supply- demand-price outlook for the product to support its own long-range price forecast. Now all the numbers are available to make a definitive appraisal of the value of the project. Cash flow analyses and sensitivity studies follow. Reams of computer printouts are generated. Time elapsed: five years. Amount spent? - up to $9 million, depending on the size, complexity and attractiveness of the project. Marginal projects always take longer. Finally, an engineering and construction (E&C) company is given the task of integrating and compiling all the data into a feasibility study. The results of dozens of reports, memoranda, computer printouts, and charts are boiled down to one final summary report of a few hundred pages together with conclusions and recommendations. After thoughtful review at a board meeting, the directors authorize management to proceed with detailed engineering work - provided that

Jan 1, 1985

Truman H. Aldrich &apos;78 Andrew S. McCreath &apos;75 W. S. Ayres &apos;73 Walter McDermott &apos;74 A. A. Blair &apos;75 Philip N. Moore &apos;74 Walter M. Brodie &apos;72 Henry S. Munroe &apos;72 H. M. Chance &apos;74 James Wilson Neill &apos;79 Frederick G. Corning &apos;77 I. P. Pardee &apos;73 Henry S. Drinker Founder Edward C. Potter &apos;79 Ernest F. Eurich &apos;74 Alexandre Pourcel &apos;77 W. E. C. Eustis &apos;76 William H. Radford &apos;76 A. Heckscher &apos;79 Robert H. Richards &apos;75 Henry D. Hibbard &apos;79 Albert F. Schneider &apos;74 Julian Kennedy &apos;79 Porter W. Shimer &apos;79 William St. George Kent &apos;72 John Stevenson, Jr &apos;76 Frank Lyman &apos;77 Arthur Thacher &apos;76 John Markle &apos;79 Edward H. Williams &apos;76 Samuel Mather &apos;79 Thomas D. Wood &apos;79

Jan 1, 1929

By J. R. Linney

Demand for eastern magnetite in 1948 necessitated practically all eastern magnetite industries to operate on a six-day week, with the result that over 11,000,000 long tons of crude ore were mined, and the shipping products amounted to approximately 5,000,. 000 long tons. Reports indicate that operating on a six-day week and doing maintenance work on the seventh day was satisfactory and resulted in excellent continuity of operation. In the Port Henry district, Republic Steel Corp. once again set new all-time records for the production of crude ore and total shipping product; 1,868,000 long tons of crude ore were mined, 945,000 from the Old Bed mine, 408,500 from the Harmony mine, and 514,500 from the Fisher Hill mine. Of the 969,000 long tons of shipping products, 663,800 long tons were sinter, 181,000 lump ore, and 115,200 con¬centrates.

Jan 1, 1949

By Hans S. Carlsson

Like most industrial processes, nuclear power production creates wastes, which have to be handled and ultimately disposed of in a safe manner. Some of the wastes contain very long-lived radioactive substances and have to be isolated for very long periods of time before they have decayed to harmless levels. Sweden, like many other countries with similar geology, intends to use crystalline rock for isolating the high-level nuclear waste from the biosphere. The suitability of a rock mass for a repository needs to be investigated extensively. Apart from the political and practical considerations for a site selection, a detailed study has to be performed in terms of geology, hydrogeology, geophysics, geochemistry and rock mechanics. The responsibility of the site selection studies in Sweden is entrusted to the Swedish Nuclear Fuel Supply Company, Division KBS (SKBF/KBS) . The paper gives a brief presentation of the "Standard Program" for the studies that will be carried out during 1980-1990. Modifications of the program are justified on the basis of gained experience or specific circumstances for each site. The program is compiled by the Geological Survey of Sweden (SGU) in cooperation with KBS.

Jan 1, 1982

By Wilbur C. Helt, Joseph J. Yancik

Throughout the history of mankind, the principal use of coal has been to produce heat through combustion. The heat is used in many ways: to warm air space for our comfort; to provide heat or energy to power industrial processes, such as cement and steel production ; and to produce electricity. Because it is our nation&apos;s most abundant fossil energy fuel, coal in the late 20th century is on the threshold of becoming a significant source for synthetic liquids and gas energy fuels for this country. This is made possible by conversion processes which can change solid coal into various synthetic gases and liquids. These coal-derived fuels are nearly identical to the processed fuels and chemicals provided by natural gas and crude oils, which presently provide almost all the petrochemical feedstocks and energy fuels needed for the residential, light commercial, and transportation markets. A revolution is beginning to take place, not only in the United States, but in many other countries with a return to a coal-based energy economy. Also, new combustion and conversion technologies which are compatible with national health and environmental goals are rapidly emerging. These technologies will allow coal&apos;s use to be expanded not only in its traditional markets, but also to supply markets held by natural gas and crude oil. With the worldwide decline in natural gas and crude oil reserves, coal is being looked upon to meet the energy demand. Because of these new coal conversion technologies, coal will no longer be only a combustion fuel, but a valuable raw material for production of a variety of clean fuels and chemicals. MARKETS FOR COAL: PAST AND FUTURE A simplified diagram of the marketing network for coal is shown in Fig. 1. As shown in this figure, coal is transported to its traditional

Jan 1, 1981

By Wilbur C. Helt, Joseph J. Yancik

Throughout the history of mankind, the principal use of coal has been to produce heat through combustion. The heat is used in many ways: to warm air space for our comfort; to provide heat or energy to power industrial processes, such as cement and steel production; and to produce electricity. Because it is our nation&apos;s most abundant fossil energy fuel, coal in the late 20th century is on the threshold of becoming a significant source for synthetic liquids and gas energy fuels for this country. This is made possible by conversion processes which can change solid coal into various synthetic gases and liquids. These coal-derived fuels are nearly identical to the processed fuels and chemicals provided by natural gas and crude oils, which presently provide almost all the petrochemical feedstocks and energy fuels needed for the residential, light commercial, and transportation markets. A revolution is beginning to take place, not only in the United States, but in many other countries with a return to a coal-based energy economy. Also, new combustion and conversion technologies which are compatible with national health arid environmental goals are rapidly emerging. These technologies will allow coal&apos;s use to be expanded not only in its traditional markets, but also to supply markets held by natural gas and crude oil. With the worldwide decline in natural gas and crude oil reserves, coal is being looked upon to meet the energy demand. Because of these new coal conversion technologies, coal will no longer be only a combustion fuel, but a valuable raw material for production of a variety of clean fuels and chemicals. MARKETS FOR COAL: PAST AND FUTURE A simplified diagram of the marketing network for coal is shown in Fig. 1. As shown in this figure, coal is transported to its traditional

Jan 1, 1981