Search Documents

By W. R. Opie, O. W. Mole

By confining the electrolytic reduction of TiCl4 to the interior of a porous basket-cathode the electrolyte between the anode and the cathode can be kept free of reduced chlorides of titanium eliminating undesirable reactions of reduced titanium chlorides with brickwork or oxygen in the cell atmosphere. Semiwalls are not needed. Operating conditions are given and discussed. Titanium yields based on TiCl4 introduced are 93 pct. Cell voltage and amperage characteristics are adaptable to multiple cathode-series cell urmngements. EXPERIMENTS conducted in the National Lead Co., Titanium Division, Research Laboratories showed that titanium metal could be deposited in an electrolytic cell in which titanium tetrachloride was introduced through a tubular cathode.' The reduced chlorides as formed were confined to the vicinity of the cathode. They were reduced to form a cocoon-shaped growth of sponge titanium metal at the end of the cathodic tube below the surface of a sodium chloride-strontium chloride electrolyte. No diaphragm was needed.' Although high-purity, coarse crystalline metal was produced in the cocoon growth, the yields of metal removed from the cell, based on the amount of titanium introduced as TiCl4, were usually only 40 to 60 pct. The growth of the cocoon deposits was away from the cathodic tube for introduction of TiC14 toward the anode following the flu lines. The reduced chlorides of titanium diffused through the deposit and were reduced to titanium electrolytically within the deposit or on the outer surfaces. Deposition within the pores of the cocoon was detrimental to further deposition because it plugged the passages used by the reduced chlorides to diffuse away from the point of titanium introduction. As plugging due to deposition in the pores proceeded, the reduced chlorides in the center of the cocoon would force their way out by forming a channel and would escape from the vicinity of the cathode without being reduced to metal. Some work had been done previously1, 2 which indicated that if the end of the cathodic tube for introducing TiC14 was surrounded by a screen connected to the tube so that it too was cathodic, growth could be made to occur within the screen. Direction of growth was observed to be from the screen toward the point of TiCl4 introduction. Through a series of design modifications a cathode evolved which consisted of an introduction tube surrounded by a perforated metal basket as shown in Fig. 1. Modifications of this design are described in Refs. 3, 4, and 5. This basic cathode designa" was incorporated in electrolytic cells containing graphite anodes and constructed of high-silica brick refractory for containing the electrolyte (see Fig. 2). The inner crucible was surrounded by insulating brick and the entire unit contained in a welded steel shell. Suitable cooling chambers with inert gas atmospheres were devised so that the cathode could be removed from the cell without exposing the deposit to air while hot. Various alkali and alkaline earth chlorides were used as electrolytes.

Jan 1, 1961

By Voyle R. McFarland, Robert A. Burmeister, David A. Stevenson

The distribution of lead between phases in the Ag-Sb-Te system was studied using microautoradio -graphy. Two compositions were investigated, both containing an intermediate phase Known as silver antimony telluride as the major phase, and one containing AgzTe and the other SbzTes as the minor phase. For both compositions, two thermal treatments were used: nonequilibrium solidification from the melt and long equilibration anneals of the as-solidified structure. For each composition, lead was segregated in the minor phase of the as-solidified structure, but was distributed in the matrix after anneal. The electrical resistivity and carrier type were insensitive to the distribution of lead in the two-phase structure. ThERE has been considerable interest in the Ag-Sb-Te system because of its thermoelectric properties. The major interest has been in compositions on the vertical section between AgzTe and SbzTes, particularly the 50 mole pct SbzTes composition AgSbTez (compositions are conveniently expressed as mole percent SbzTes along the AgzTe-SbzTes section). One of the major problems in the proper evaluation and utilization of this material is the inability to control the electrical properties through impurity additions: all alloys prepared to date have been p-type, even with the addition of large amounts of impurities. It has been shown Wit all the compositions previously studied contain an intermediate phase of the NaCl st'ructure as a major phase (denoted by b) and a second phase, either AgzTe or SbzTe3, as a minor phase.'-3 One explanation for the unusual electrical behavior of this material is that the impurity additions have a higher solubility in the second phase than in the matrix; the impurity would segregate to the second phase, leaving the bulk matrix essentially free of impurity.4 In order to investigate this mechanism with a specific impurity element, the distribution of lead between the two phases was determined using autoradiography. Lead 210 was chosen because of the suitability of its 0.029 mev 0 particle for autoradiography and also because of the interest in lead as an impurity in this system.5'6 EXPERIMENTAL PROCEDURE Two compositions were taken from the vertical section between AgzTe and SbzTes, 50 mole pet SbzTes (Viz. AgSbTez) and 75 mole pct SbzTes, in which AgzTe and SbzTes appear, respectively, as the minor phase. Lead containing radioactive lead (pb210) was added to the above compositions to provide a concentration of 0.1 wt pct Pb. The material was placed in a graphite crucible in a quartz tube which was then evacuated and sealed. The samples were melted and solidified by cooling at a rate of 8°C per min and then removed and prepared for microa~toradiography. After autoradiographic examination of these samples, they were again encapsulated and annealed in an isothermal bath at 300°C for a number of days and prepared for examination. An alternate method of preparation employed a zone-melting furnace; the molten zone traversed the sample at a rate of 1.2 cm per hr and the solid was maintained at a temperature of 500°C both before and after solidification. This treatment had the same effect as solidification at a slow rate followed by an anneal for several hours at 500°C. In order to obtain the best resolution, thin sections of the alloy were prepared by hand lapping to a thickness of approximately 20 p. Other samples were prepared for examination by lapping a flat surface on the bulk sample. The resolution, although somewhat better in the former procedure, was adequate in both instances and the majority of the samples were treated in the latter fashion. A piece of autoradiographic film (Kodak Experimental SP 764 Autoradiographic Permeable Base Safety Stripping Film) was stripped from its backing, care being taken to avoid fogging due to static-electrical discharge. A small amount of water was placed on the sample, the film applied emulsion side down on the surface of the sample, and the sample and the film dipped into water in order to assure smooth contact. After drying, the film was exposed for 2 to 5 days, the period of time selected to give the best resolution. The film was developed on the specimen and fixed and washed in place. Two major factors must be considered in establishing the reliability of an autoradiograph: the in-

Jan 1, 1964

By P. A. Laxen, H. R. Spedden

WHEN a mineral particle is fractured, bonds between the atoms are broken. The unsatisfied forces that appear at the newly formed surface are considered to be responsible for the adsorption of ions at the mineral surface. A knowledge of the mechanism and extent of ion sorption from solution onto a mineral surface is of interest in the development of the theory of flotation.'*' Study of the adsorption of sodium from an aqueous solution oftheon quartz offers a simple approach to this complicated problem. The availability of a radioisotope as a tracer element meant that accurate data could be obtained."." Three main factors which appeared likely to affect the adsorption of sodium are: l—concentration of sodium in the solution, 2—concentration of onotherof cations in the solution, and 3—anions present in the solution. Hydrogen and hydroxyl ions are always present in an aqueous solution. By controlling the pH, the concentration of these two ions was kept constant. The variation in thesethe amount of sodium adsorbed with variation in sodium concentration was then determined under conditions standardized in regard to hydrogen ion. The effect of concentration of hydrogen ions and of other cations was also measured. A few experiments were made to get a preliminary idea on the effect of anions. The active isotope of sodium was available as sodium nitrate. Standard sodium nitrate solutions were used throughout these experiments except when the effects of other anions were studied. It was found that sodium adsorption increased with sodium-ion concentration, but less rapidly than in proportion to it. Increasing hydrogen-ion concentration, or conversely decreasing hydroxyl-ion, brings about a comparatively slight decrease in sodium-ion adsorption. Increasing the concentration of cations other than hydrogen or sodium decreases somewhat the adsorption of sodium ion. It would appear as if the kind of anion is a secondary factor in guiding the amount of sodium ion that is adsorbed. Materials and Methods Quartz The quartz was prepared as in previous work in the Robert H. Richards Mineral Engineering Laboratory' except for the refinement of using de-ionized distilled water for the final washing of the sized quartz, prior to drying." To minimize the laborious preparation of quartz, experiments were made to determine .whether the sodium-covered quartz could be washed free of sodium and re-used. The experiments were successful as indicated by lack of Na" activity on the repurified material and by its characteristic sodium adsorption. Table I gives the spectrographic analyses of the quartz used. The quartz ranged from 16 to 40 microns in size, averaging about 23 microns (microscope measurement), and had a surface of 1850 sq cm per g (lot I), 2210 (lot 11) and 2000 (lot 111) as determined by the Bloecher method." Radioactive Sodium Method of Beta Counting for Adsorbed Sodium: Na22, the radioisotope of sodium, possesses convenient properties.' It has a half-life of 3 years, thus requiring no allowance for decay during an experiment. On decay it emits a 0.575 mev ß+ radiation and a 1.30 mev r radiation. The decay scheme is illustrated in the following equation: ß+ NaR-------'8'77NeZ2 3 years The /3 radiation is sufficiently strong to penetrate an end-window type of Geiger-Mueller counting tube. This, in turn, makes it possible to use external counting, a great advantage in technique. Furthermore, it permits the assaying of solids arranged in infinite thickness, while assaying evaporated liquors on standardized planchets. The equipment used was standard and similar to that employed by Chang.R The original active material was 1 ml of solution containing 1 millicurie of Na" as nitrate. This active solution was diluted to 1000 ml. Five milliliters of this diluted active solution was found to give a quartz sample a sufficiently high activity for accurate evaluation of the sodium partition in the adsorption measurements. Also, 1 ml of final solution gave a sufficiently high count for precision on the liquor analyses. The sodium concentration of the diluted active solution was 1.2 mg per liter, so that 6 mg of sodium for 60 ml of test solution and 12 g of quartz was the minimum amount used. The active solution was stored in a Saftepak bottle. Procedure for Adsorption Tests: The method consisted of agitating 12 g of quartz with 60 ml of solution of known sodium concentration for enough time to establish equilibrium between the solution and the quartz surface. The quartz was separated as completely as possible from the solution by filtering and centrifuging. The activity on the quartz and in the equilibrium solution was measured and the partition of the sodium was calculated from the resulting data. The detailed procedure for the adsorption test is set forth in a thesis by Laxen." In brief, it included the following steps: 1—Ascertainment of linearity between concentration of Na" and activity measured. 2—Evaluation of factor to translate activity on solid of infinite thickness in terms of activity on an evaporated active film of minute thickness, on the various shelves of the counter shield. 3—Taking precautions to avoid evaporation of water during centrifuging

Jan 1, 1953

By P. A. Laxen, H. R. Spedden

WHEN a mineral particle is fractured, bonds between the atoms are broken. The unsatisfied forces that appear at the newly formed surface are considered to be responsible for the adsorption of ions at the mineral surface. A knowledge of the mechanism and extent of ion sorption from solution onto a mineral surface is of interest in the development of the theory of flotation.'*' Study of the adsorption of sodium from an aqueous solution oftheon quartz offers a simple approach to this complicated problem. The availability of a radioisotope as a tracer element meant that accurate data could be obtained."." Three main factors which appeared likely to affect the adsorption of sodium are: l—concentration of sodium in the solution, 2—concentration of onotherof cations in the solution, and 3—anions present in the solution. Hydrogen and hydroxyl ions are always present in an aqueous solution. By controlling the pH, the concentration of these two ions was kept constant. The variation in thesethe amount of sodium adsorbed with variation in sodium concentration was then determined under conditions standardized in regard to hydrogen ion. The effect of concentration of hydrogen ions and of other cations was also measured. A few experiments were made to get a preliminary idea on the effect of anions. The active isotope of sodium was available as sodium nitrate. Standard sodium nitrate solutions were used throughout these experiments except when the effects of other anions were studied. It was found that sodium adsorption increased with sodium-ion concentration, but less rapidly than in proportion to it. Increasing hydrogen-ion concentration, or conversely decreasing hydroxyl-ion, brings about a comparatively slight decrease in sodium-ion adsorption. Increasing the concentration of cations other than hydrogen or sodium decreases somewhat the adsorption of sodium ion. It would appear as if the kind of anion is a secondary factor in guiding the amount of sodium ion that is adsorbed. Materials and Methods Quartz The quartz was prepared as in previous work in the Robert H. Richards Mineral Engineering Laboratory' except for the refinement of using de-ionized distilled water for the final washing of the sized quartz, prior to drying." To minimize the laborious preparation of quartz, experiments were made to determine .whether the sodium-covered quartz could be washed free of sodium and re-used. The experiments were successful as indicated by lack of Na" activity on the repurified material and by its characteristic sodium adsorption. Table I gives the spectrographic analyses of the quartz used. The quartz ranged from 16 to 40 microns in size, averaging about 23 microns (microscope measurement), and had a surface of 1850 sq cm per g (lot I), 2210 (lot 11) and 2000 (lot 111) as determined by the Bloecher method." Radioactive Sodium Method of Beta Counting for Adsorbed Sodium: Na22, the radioisotope of sodium, possesses convenient properties.' It has a half-life of 3 years, thus requiring no allowance for decay during an experiment. On decay it emits a 0.575 mev ß+ radiation and a 1.30 mev r radiation. The decay scheme is illustrated in the following equation: ß+ NaR-------'8'77NeZ2 3 years The /3 radiation is sufficiently strong to penetrate an end-window type of Geiger-Mueller counting tube. This, in turn, makes it possible to use external counting, a great advantage in technique. Furthermore, it permits the assaying of solids arranged in infinite thickness, while assaying evaporated liquors on standardized planchets. The equipment used was standard and similar to that employed by Chang.R The original active material was 1 ml of solution containing 1 millicurie of Na" as nitrate. This active solution was diluted to 1000 ml. Five milliliters of this diluted active solution was found to give a quartz sample a sufficiently high activity for accurate evaluation of the sodium partition in the adsorption measurements. Also, 1 ml of final solution gave a sufficiently high count for precision on the liquor analyses. The sodium concentration of the diluted active solution was 1.2 mg per liter, so that 6 mg of sodium for 60 ml of test solution and 12 g of quartz was the minimum amount used. The active solution was stored in a Saftepak bottle. Procedure for Adsorption Tests: The method consisted of agitating 12 g of quartz with 60 ml of solution of known sodium concentration for enough time to establish equilibrium between the solution and the quartz surface. The quartz was separated as completely as possible from the solution by filtering and centrifuging. The activity on the quartz and in the equilibrium solution was measured and the partition of the sodium was calculated from the resulting data. The detailed procedure for the adsorption test is set forth in a thesis by Laxen." In brief, it included the following steps: 1—Ascertainment of linearity between concentration of Na" and activity measured. 2—Evaluation of factor to translate activity on solid of infinite thickness in terms of activity on an evaporated active film of minute thickness, on the various shelves of the counter shield. 3—Taking precautions to avoid evaporation of water during centrifuging

Jan 1, 1953

By W. Crafts, J. L. Lamont

Electrolytic extraction of carbides from quenched and tempered steel and their examination under the electron microscope were found to be helpful in understanding the mechanism of secondary hardening in alloy steels1 and the same technique has been applied to isothermally transformed steels. A preliminary survey of the utility of the method has indicated that it has promising possibilities for investigating the characteristics of pearlite and bainite. The examination of a few carbon and chromium steels has suggested that pearlite is formed with carbides of two varieties representing the lamellar and nonlamellar forms and that bainite appears to form with a structure analogous to, but significantly different from, martensite. Procedure The method used for examining the carbides was similar to that described previously.1 The chromium steels used in the investigation were made from an Armco iron base in an induction furnace and were not treated with grain-refining deoxidizers. The composition of the steels is given in Table 1. Three-inch square ingots were forged and rolled to 1/8-in. thick sheet for use in the isothermal studies. After rolling, the sheets were sandblasted to remove the rolling scale. Specimens approximately 3/4-in. wide and l1/2-in. long were prepared from the 1/8-in. sheet. They were heated in a salt "bath at 2100°F (1150°C) for 1/2 hour, transferred to other salt baths at 1300°F (704°C), 1000°F (538°C), 800°F (426°C), or 600°F (315°C), held for various periods up to 100 hr and finally quenched in water. After quenching, the specimens were cut in half, one half being submitted to microscopic examination and the other half being used for the electrolytic extraction. The isothermally transformed specimens were submitted to examination under the light microscope to determine the degree of transformation and type of structure and were photographed at 2000 X. Carbide residues were obtained by electrolyzing in 10 pet hydrochloric acid and collecting the residue in glycerine to minimize attack by the acid. As pointed out in the earlier paper, the carbides are attacked to some degree during electrolysis. This attack is relatively minor on the coarser carbides but may be quite severe on the fine bainitic carbides. The residues were washed free of the glycerine with water and alcohol. The alcohol was removed by repeated washings of amyl acetate, and the amyl acetate suspensions were transferred to stoppered vials. Debye-Sherrer X ray diffraction patterns of the residues were prepared using a chromium target. A selection based on the microstructure and X ray data was then made of samples considered most illustrative of the progress of transformation. Electrolytically extracted residues from these samples were submitted to examination by W. D. Forgeng and A. C. Jenkins on the electron microscope at the Research Laboratories of The Linde Air Products Co. and electron micrographs were made at X 5000 and enlarged to 25,000 X. The micrographs obtained with both the light and the electron microscopes are mounted side by side in the accompanying figures. Although no effort was made to establish the T-T-T diagram for the chromium steels, the times for holding in the salt bath were adjusted with the intention of making the samples represent different stages in the transformation at temperatures of 600, 800, 1000, and 1300°F. The degrees of transformation and results of X ray examination are shown in Tables 2—4. The carbide designations refer to orthorhombic or trigonal carbide types and are not meant to imply that the compositions are exactly as indicated. X ray Diffraction Data The occurrence of Fe3C and Cr7C3 in these steels was found to be consistent with published data on comparable chromium steels. Steels A and B with relatively low ratios of carbon to chromium contained Cr7C3 in the pearlitic structures and FeuC in the

Jan 1, 1950

By H. W. Highriter

THE method developed and used in this laboratory for the production of metallic uranium of such purity that it is ductile and can be cold-worked to fine wire or thin sheet by rolling has already been described1. It consists, briefly, in the electrolysis of potassium uranous fluoride (KUF5) in a molten bath composed of equal parts of sodium and calcium chlorides. The bath is contained in a graphite crucible, electrically heated to about 775° C., the crucible serving as the anode for electrolysis. The uranium deposits in finely divided form mixed with salts upon a molybdenum cathode suspended axially in the crucible. Upon com-pletion of the electrolysis the cathode is removed and cooled, the deposit broken and leached to remove salts. The metal powder is washed with water and dilute acetic acid and dried in vacuo to reduce oxidation. Suitable amounts are then pressed into pellets and heated in vacuo by high-frequency induction, using a thoria crucible. The uranium melts and flows away from the pellet, leaving a shell, which is largely oxide. In general, this method produced a satisfactory metal, although at times the uranium was not ductile. The investigations recorded here were made to find the cause of this embrittlement. It was known that the metal generally contained carbon, derived from disintegration of the graphite crucible in which electrolysis is conducted, in amounts dependent upon the thoroughness of washing the metal powder. Accordingly, analyses of several samples, both ductile and brittle, were made by combustion and absorption of C02 in Ascarite, using air instead of oxygen to reduce the temperature and rate of oxida-tion. Several of these metals were made with special precautions to reduce carbon content. The results show no relationship between ductility and carbon content in the range investigated (Table 1).

Jan 1, 1935

By C. G. Dunn, F. W. Daniels, M. J. Bolton

J. P. Nielsen—The data that Dr. Dunn and his associates have been obtaining are welcome checks on the theoretical aspects of grain boundary energies. With reference to the comments on the validity of the inter-facial tension concept, I should like to say that I have been having considerable difficulty myself in untangling the confusion between "interfacial tension" and "interfacial energy." The confusion however resolved itself for me when I learned that "interfacial tension" for solids, or at least crystals, is used with two distinct meanings. One meaning12. ' "hat is implied for "interfacial tension" is the work necessary to produce or increase the surface of the solid in question by a unit area, temperature and pressure held constant. This comes from the somewhat surprising but simple fact that surface tension and surface energy in the case of liquids are identical quantities. This synonymity has carried over to crystals, where it should be kept in mind that the tension connotation has meaning only by analogy with liquids and that no real stresses are being referred to. The only reason that there is apparently a set of stresses acting at a grain boundary junction is the optical illusion that liquid interfaces are being observed for the grain boundaries. The other meaning3,14,15 for the term has to do with actual states of stress in the surface of a material as would be measured by a system of forces applied to the surface to equate the surface stress state with that in the body of the crystal. J. B. Hess—Since the authors have proposed that the surface tension concept should be discarded in order to deal with the general case of interface energies in solids, their attention should be called to a recent paper by Gurney." The latter has shown, from a thermodynamic argument, that surface tension is a valid concept in solids. In fact, Gurney has rejected the idea that surface tensions are merely mathematical fiction and, instead, has given an interpretation of their physical reality. Finally, he has concluded that, as long as appreciable atomic migration takes place, specific surface energies and surface tensions must be equivalent in solids as well as in liquids. Accordingly, the authors' eqs 2 and 3 can be written with equal accuracy in terms of interface tensions, simply by replacing each E,! with its numerically and dimension-ally equivalent Interfacial tension ?,,. If the interfacial tensions (or specific energies) are independent of interfacial orientation, as is true in liquids, then the general equations that define the geometry at equilibrium of the common junction of three interfaces reduce to eq 1. However, neglect of the effect of boundary orientation is never completely justified theoretically' in dealing with crystalline solids; hence, use of eq 1 in such cases must always be considered as an approximation, though clearly a reasonable one for many purposes.1,2 At the same time, one should not be surprised that the assumption that interface tensions in solids are free from orientation

Jan 1, 1951

By Roger W. Dewey

The opposition is all kinds. There are extremists. There are quiet, sensible sounding folk who can twist numbers and facts to make their point. But they are all out to shut you down! Some of them are genuinely concerned about miners' impact on the environment. Others are just anti- society, anti-big business - small is beautiful - live naturally. The opportunity for them to make those statements on television was provided by us, the Uranium Public Affairs Task Force, as part of a media tour of the State of Idaho in May. We fielded four representatives of the industry and got 25 hours of television coverage, 22 hours of radio coverage, and print coverage by every paper in Idaho. The tour included several debates, and these clips are from two of them. Our folks creamed them! This one was so upset that he ran off the set while his mike was still plugged in, trailing studio equipment behind him. But we don't always have the opportunity to rebut them. They are making these statements all the time, everywhere they can. They have learned their trade well. They use the hearing process like A1 Hirt uses the trumpet. If the process of intervention should shut us down or prevent us from getting a license, so much to the good. But even if it doesn't - they win - for it causes delay - delay costs money and so does complying with regulation. If they can make us uneconomic, and that's not too hard to do these days, they have won. Regulation restricts the decision process. Any time the decision process IS restricted, you face the possible loss of a more economic alternative. They are out to pile every regulation on you they can and every delay they can. Initiatives! They came after us - the uranium industry - in South Dakota and Montana last year. They won in Montana. We tried to reverse it in the legislature, but they were too frightened of public reaction to do it. They did put it on the ballot for reversal in November of '82. That puts it squarely up to us to influence the public so we can win a campaign. There will be more initiatives, and at local levels as well as at state. We must join together and win! The public generally supports the continued operation of nuclear power plants. They about split on whether to build more. But they strongly support regulating the industry more stringently. Every survey reflects concern about safety and the desire for the government to take responsibility and regulate. You and I know that regulation nearly always adds cost, and only sometimes increases safety. We need to influence the creation of regulation. We need to accept responsible regulation and fight that which is counter-productive. To win in hearings, to win initiatives, to win in getting responsible regulation, we need public support. We need an informed, understanding, and supportive public. To accomplish this, we need two kinds of efforts. The first is to reach the people at the local level with local representatives of our industry. Informal conversations at church, PTA, cocktail parties, whatever. Presentations to Kiwanis Clubs, League of Women Voters, church groups - wherever we can. Facts, information in printed form, to these same local audiences with the credibility of the local sources. The second is to reach mass audiences through the media. Positive media. This can be done by advertising, but it is very expensive. We have to look to influencing the reporters and editors to get more balanced and accurate reporting. We need to get free time - interviews, debates, letters to the editors, etc. The Uranium Public Affairs Task Force was created last year to provide tools for you to use to reach these audiences (it is affiliated with the Atomic Industrial Forum). Twenty-two companies provided money and man- power. A consultant, Denver Research Group, was retained to produce materials. In this Phase I effort, we first researched what issues were of greatest concern and what were felt to be the greatest needs in materials. We determined that we did not have the funds to go out and do the job for the industry, so we decided to develop tools for the Industry to go out and do the job for itself. From the research, we determined what tools we should develop for you to use. We first developed a set of the quest- ions most likely to be asked of you and the issues most likely to be thrown up to you. We have developed a loose-leaf notebook. Each page contains one of those questions or issues, a short verbatim response that you can use, a short discussion of the subject, and references you can cite or research for further information. It is organized by subject: tailings, water radiation, etc. This book is an extremely handy tool for anyone in the industry. Each uranium location should have at least one.

Jan 1, 1982

By F. H. Buttner, H. Udin, J. Wulff

Using a modified Udin, Shaler, and Wulff technique, the surface tension of gold Udin, purified helium was found to be 1400 ± 65 dynes per cm for the temperature range 1017° to 1042°C. IN the original Udin, Shaler, and Wulff technique for measuring the surface tension of copper: variously weighted wires were allowed to extend or contract in a copper cell held at elevated temperatures in vacuum. By plotting stress vs. strain for a wire array in one test, the stress at zero strain is obtained. This is the point where the contractile forces resulting from surface tension are balanced by the applied load, according to the expression: y = e=o r [1] where y is the surface tension in dynes per cm; a,,,, the stress at zero strain in dynes per cm; and T, the radius of the wire in cm. The assumption that the wires deform viscously permits the drawing of a straight line through the points on the stress-strain plot. Justification of the assumption has received further experimental support recently.'-' The presence of grain boundaries in the wires requires a correction to the original expression used." Thus: y = d4=T [l- (dl) (ar)Y1 [2] where, n/l is the number of grain boundaries per unit length, and a, the ratio of grain boundary tension to free surface tension. Alexander, Kuczynski, and Dawson in studying the creep of gold wire in vacuum were unable to obtain reproducible values of the surface tension of gold. In plotting stress vs. strain for progressively longer times, they found that the stress at zero strain drifted with time from positive stress values to negative values. Similarly, for the surface tension of silver, reproducible values were obtained only when a purified helium atmosphere was substituted.' Evidently the evaporation rate of silver in vacuum is too high at the temperatures employed to obtain solid-gas equilibrium even in a similar metal enclosure. Thus reproducibility of results is lost. Experimental Procedure The experimental procedure was much the same as that originally developed by Udin, Shaler, and Wulff with a few modifications and improvements. For greater accuracy in strain measurements, knots gave way to cut gage marks as shown in Fig. 1. These were made with a hand-driven lathe in which razor blades serv'ed as cutting tools. Also a more precise cathetometer with a screw accurate to 0.00015 cm was used. The tests were conducted in an atmosphere of purified .helium rather than in vacuum in order to avoid possible evaporation difficulties. Five mil wire of high purity gold (99.98 pct) was used. After cutting in the gage marks, each wire of a series of about 12 was differently loaded by welding a gold ball to one end. This was done by dipping the end of the wire in a cooling gold droplet, previously melted on a charcoal block with a No. 2 acetylene torch. The other end of the wire was strung through a hole in a gold lid and twisted over the edge to hold the wires fixed and in suspension from the lid. The lid and mounted wires were then dipped in pure ethyl alcohol to dissolve any skin oils and dirt on the surface of the wires due to handling. Finally the lid was put in place on an alundum crucible lined with gold so that the wires hung freely within the gold-lined chamber. This whole assembly was next heated in a quartz nichrome wound tube furnace and heated for a few minutes at 600°C to soften the wires. After this anneal the wires were easily straightened with tweezers. The wire assembly was finally annealed 10" to 25°C above the subsequent test temperature for 2 hr. This treatment allowed the grains to grow to equilibrium size and shape. After the anneal, the lid was mounted in front of the cathetometer. The gage length was measured by sighting the 40 power microscope on the upper lip of the lower gage mark for the first reading, then traveling up to the lower lip of the upper gage mark for the final reading. This procedure was repeated four times to give an average gage length value. In this manner the annealed gage length and the final gage length could be measured to determine the strains. During all measurements, grain counts were made.

Jan 1, 1952

By G. B. Craig, H. E. Rosinger, W. J. Bratina

NUMEROUS studies have been reported on how the mechanical properties of a bcc metal are affected by interstitial solute atoms in the temperature range where appreciable diffusion occurs in finite time. Only recently, though, has work on an "interstitial-free" iron been reported, this by Leslie and sober,' on an Fe-0.15 pct Ti alloy. The data was limited to a maximum temperature of 296°K. This work presents a systematic study of the flow stress and the activation volume of a similar material as a function of plastic deformation over the temperature range 253" to 473°K. The material studied was Ferrovac E iron containing 0.01 wt pct C and 0.0002 wt pct N annealed at 870°C for 1 hr, and the same iron with an addition of 0.15 wt pct Ti annealed at 870°C for 80 hr; cooling rates being 75°C per hr. In the latter alloy depletion of interstitials in the a-iron matrix associated with the second phase formation was expected. The temperature dependence of the flow stress was measured at 6 = 3.33 x 10-5 sec-1 from 253" to 473°K as a function of the deformation in 0.01 intervals from 0.03 to 0.12 strain. Results for two strains, 0.03 and 0.09 are shown in Fig. 1. The flow stress increased and reached a maximum in the Ferrovac E iron with increasing temperature, but showed a consistent gradual decrease in the Ferrovac E-0.15 pct Ti alloy. A yield point and Luders region, observed in Ferrovac E, was absent in the Ferrovac E-0.15 pct Ti alloy. Also, the Ferrovac E exhibited a serrated stress-strain behavior in the temperature range 330" to 400°K; dynamic strain-aging characteristics were absent for the titanium alloy. The activation volume was determined over the same temperature range by the method of stress relaxation at constant strain. Results are shown in Fig. 2. At the temperatures of serrated stress-strain behavior in Ferrovac E the activation volume was found to increase toward infinity and, as the temperature rose, to decrease, to about 100 to 200 v/b3. By contrast, the activation volume for the Ferrovac E-0.15 pct Ti alloy tended to increase continuously from the initial value of approximately 300 at 300°K to more than 800 at 473°K. Above 400°K, then, the corresponding activation volume values of Ferrovac E were less than that of the Ferrovac E-0.15 pct Ti alloy. The activation volumes, Fig. 2, appear to depend on dislocation-interstitial interaction in Ferrovac E and on dislocation-dislocation interaction in Ferrovac E-0.15 pct Ti alloy. The gradual increase in the latter metal is associated with thermally activated motion of dislocation segments.' The decrease of the activation volume in Ferrovac E above 400°K is probably related to the diminishing effect of interstitials on dislocations. Here, the interstitials can be moved along with a dislocation without appreciable drag. As indicated in Fig. 1, removal of interstitials

Jan 1, 1970

By Rixford A. Beals

It has been observed with considerable accuracy that if the major U. S. mines were moved to Mexico tomorrow, many of them would be losing money. But the companies would continue to operate, losses or not, because they would have to. And some of the newest and most promising low grade ore projects in the U. S. would never have "gotten off the ground" had they faced the equivalent of the mining taxes now in effect in Mexico. No one of the various mining taxes in Mexico seems prohibitive by itself. Taken together, on the balance sheet, however, the picture changes. Production and export taxes alone take from 20 to 40 pct of the gross product value for base and precious metals.

Jan 2, 1955

NEW MEMBERS The following list comprises the names of those persons who became members during. the period Mar. 10, 1919, to Apr. 10, 1919. AFFLECK, B. F., Pres., Universal Portland Cement Co., 210 So. La Salle St., Chicago, Ill. BENSUSAN, ARTHUR J., The Ouro Preto Gold Mines of Brazil, Ltd., Passagem de Marianna, Minas Geraes, Brazil, S. A. BIERBAUM, CHRISTOPHER H., Cons. Engr., & Vice-pres., Lumen Bearing Co., Buffalo, N. Y . DEWITT, OSCAR E., Geol., Vinegar Hill Zinc Co., 622 North Court St., Platteville, Wis. DOTY, L. C Mine Supt., Bullion Beck & Champion Co., Box C, Eureka, Utah. ESPIE, FRANK F Burma Mines, Ltd., Namtu, Upper Burma, Asia. FOZARD, J. L., Gen'l Supt., Beatson Mines, Kennecott Copper Corpn., Latouche, Alaska. GRANT, BENERE Supt., Bulluhacker Min. Co., Butte Mont. HARDEL, JEAN A., Engr., French Government, 21 Rue du Colonel Moll, Paris, France. JANSSEN, WALTER A., Operating Mgr., Canadian Steel Foundries.Ltd., 120 St. James St., Transportation Bldg., Montreal, Canada. KNOWLES, RALPH Roy, Supt., Radium Plant, The Minerals Recovery Co., 457 So. Elati St. Denver Colo.

Jan 5, 1919

By J. B. Hess, C. S. Barrett

TO reach equilibrium between different phases in cobalt-rich alloys requires prohibitively long annealing cobalt-richalloystimes when temperatures are below about 700°C. The fact that a transformation from face-centered cubic to close-packed hexagonal readily tered takes place at temperatures below this in the cobalt-rich solid solutions is not an indication that thermally activated processes occur at an appreciable rate, for the transformation is well established as martensitic in nature. Wide divergence between heating and cooling experiments and high sensitivity to prior heat treatment make it difficult to judge temperatures of equilibrium between the phases.&apos; One object of the present work was to see if the information object of on the relative stability of phases could be gained by substituting plastic deformation for thermal agitation. Procedures were worked out that led to the determination of a diffusionless type of phase diagram, which represents the temperature of of phase equal stability for phases of the same composition, and the technique was applied to the Co-Ni system. Another object of the work was to see whether or not deformation would generate frequent stacking faults when these were thin lamellae of quentstackingfaultsa phase having higher free energy than the parent phase. The alloys were prepared in 80 to 100 g melts from cobalt (with metallic impurities estimated spectrochemically as follows: Ni, 0.05 pct; Fe, 0.001 pct.; Mg, Si, Cu, Cr, Al, < 0.001 pct) and Mond Car-bony1 nickel (with Fe, 0.05 pct; Si, 0.003 pct; C, 0.61 pct.; Cu, 0.001 pct; Co, Cr not detected, < 0.01 pct). The metals were melted in pure Al2O3 crucibles. An atmosphere of argon, that had been purified by passing over hot magnesium chips, was used for the alloys that, by analysis of the portions of the ingots actually used, were found to contain 15.3, 25.7, and 35.0 pct Ni, and vacuum melting (after degassing) was used for those containing 29.4 and 31.5 pct Ni. After induction melting the alloys were allowed to solidify in the crucible, and slices % in. thick x ½ in. in diam were annealed 12 hr at 1350°C for homogenization. These same specimens were used throughout the series of experiments, with annealing treatments of 4 hr at 900°C in purified hydrogen followed by furnace cooling, alternating with the deformation and X-ray tests discussed below. Results Spontaneous transformation was observed on cooling to room temperature in all alloys containing 29.4 pct Ni or less and by cooling the 31.5 pct alloy to — 195°C but was not observed in the 35 pct alloys after cooling to —195°C. These results are in satisfactory agreement with the cooling experiments of Masimoto.4 From these data it is clear that the temperature of beginning transformation M,,, drops to 20°C with the addition of about 30 pct Ni. The test for spontaneous transformation was metallographic. Specimens were thermally polished by annealing 10 hr in hydrogen at 1350°C, then furnace cooled; if trans- formation had occurred there were relief effects visible on the thermally polished surfaces. These markings were narrow straight lines, usually resolvable at high magnification as clusters of fine lines that resembled slip lines. It was concluded that they resulted from displacements on (111) planes, for the number of directions in individual grains often reached but never exceeded four, and lines could always be found parallel to the thermally etched (111) boundaries of annealing twins. The markings were thus consistent with the idea that the transformation occurs by (111) plane displacements (Shockley partial dislocations moving on (111) planes). This was further confirmed by X-ray tests for stacking disorders. Using an oscillating crystal technique previously employed to detect strain-induced faulting in Cu-Si alloys," streaks indicative of the stacking faults were looked for and found on X-ray films of the spontaneously transformed 25.7 pct Ni alloys, as expected by analogy with Edwards and Lipson&apos;s results on pure cobalt." The streaks were much intensified after rolling at room temperature. Transformation induced by plastic strain was investigated as a function of alloy composition and temperature of deformation. A series of tests was made to determine suitable straining and X-raying techniques. Filing was found inferior to abrasion in converting cubic samples to hexagonal, and abrasion was less effective than peening in producing smooth unspotty Debye rings in the X-ray patterns. Because the diffraction lines were broad, Geiger-counter spectrometer records of filings were less sensitive in revealing small amounts of transformed material than X-ray patterns recorded on films in a small diameter camera. After these exploratory tests the following methods were adopted. Specimens that had been annealed at least 4 hr at 900°C and furnace cooled were mounted in a block of aluminum, brought to temperature, and peened thoroughly with a mullite pestle preheated to the same temperature. The specimens were then quenched to room temperature. In peening, a circular area of % in. diam was given 500 blows. A few control tests showed that an additional 1000 blows did not detectably change the proportions of the phases present. The amount of transformation was judged by X-ray reflection patterns from the peened surface, using the innermost four lines of the cubic and the hexagonal patterns with filtered CoKa radiation,

Jan 1, 1953

By Harry M. Mikami, A. Gene Sidler

Chemistry of the evolution of materials in contact with copper converter tuyeres is delineated by means of analyses of periodic punch rod samples taken during a converter cycle. Lining samples from known peripheral and end locations from three converters were investigated chemically and petrographically. One set of eight specimens representative of all lining parts was removed for study before completion of the campaign. Purely surface removal by slag action is minor. Slag filling of interconnecting cracks extending to the hot face results in a "stoping&apos;&apos; action which shapes the hot face contour and is a significant factor. Major wear mechanism is believed to be copper metal slabbbing caused by metal first penetrating joins and invading fractures or impregnating brick structure laterally from the joints. Importance of lining design and joint fit are emphasized. New laboratory tests are indicated. In the copper converter, molten matte, which is essentially a solution of iron and copper sulfides, is blown with air to produce blister copper. During the first stage of the process the FeS component is oxidized to SOz and FeO, the latter combining with a siliceous flux to form a predominantly ferrous silicate slag. Successive increments of matte and flux are charged, blown, and skimmed of slag until sufficient CuzS ("white metal") has accumulated. This white metal is then blown to copper metal in the final or blister-forming stage by the oxidation of sulfur to SOz and the reduction of combined copper to metal. The reactions of both stages are exothermic so provide the required heat. Temperature is controlled by cold scrap copper, flue dusts, smelter reverts, and so forth. Considerable vari- ation in practices occur depending on the type of converter, grades of the matte and flu, and other factors. Lathe and Hodnett&apos;s&apos; survey of world converter practices gives much information on these variations and their effects on the refractories. Principles of converting chemistry are presented by Newton and wilson,&apos; Ruddle,&apos; and schuhmann. Most copper converting occurs within the temperature range 2100" to 2370°F although individual smelters report1 ranges from as low as 1700" to 2240°F to a high of 2200" to 2400°F. Temperature intervals reported from beginning to end of blow varied from 45" to 540°F. Average temperature range was 2030" to 2260°F and the average interval 250°F During the matte-blowing stage varying amounts of magnetite (FeO.Fe,O,) are formed in the slag as suspended crystals and also the liquid portion of the slag will contain, in addition to ferrous silicate, some Fe20s which adds to the potential magnetite formation if the temperature falls. This is a component of the so-called "dissolved magnetite" often referred to in the literature. Although the slag may contain minor amounts of CaO, A1209, MgO, and alkalies, the principal components are Fe0-Fez03-SiO,. The phase equilibria relationships of this system have been elucidated by Muan~ and Schuhmann, et a1.&apos; These data and estimates of converting atmospheres by schuhmann4 are useful tools in studying slag behavior. It would appear that in many cases reported magnetite contents of slags are apparently higher than actually is present at operating temperature. This is probably because much of it is formed during slag solidification. The quaternary systems which have Mg-0,1,0,&apos; and addition to iron oxides and silica are also of interest in considering the reactions of the slags with basic refractories. The formation of magnetite has an important interrelationship throughout the pyrometallurgy of copper (Mossman,&apos; Gronningsater and Drummond," Ruddle,&apos; Elwood and Henderson") but its presence in the converter particularly relates to operating efficiency and lining life in certain instances. Archi-

Jan 1, 1963

By Fred H. Poettmann

The vaporization characteristics of carbon dioxide in a League City natural gas - Billings crude oil system were studied at three temperatures, 38°. 120°, and 202°F and for pressures ranging from 600 to 8,500 psi. Variation of carbon dioxide concentration up to 12 mole per cent in the composite showed no effect on the equilibrium vaporization ratios (K values) of the hydrocarbon constituents or on the K value of carbon dioxide itself. It was shown that carbon dioxide is more soluble in crudes than in distillates which is contrary to the behavior of methane. A working chart of carbon dioxide K values is presented. INTRODUCTION The study of the equilibrium vaporization ratios of mixtures of paraffin hydrocarbons has been rather thorough.2,6,7,8,9 In the past few years considerable attention has been paid to the vaporization characteristics of the so-called noncondensable gases such as nitrogen, carbon dioxide, and hydrogen sulfide in mixtures of hydrocarbons. since they usually occur to some extent in most crude oils and natural gases.1,3,4,5 Knowledge of this behavior is useful to both the production and refining phases of the petroleum industry. This paper reports the equilibrium vaporization ratios (K&apos;s) of carbon dioxide in a mixture of League City natural gas and Billings crude oil, and compares them to those obtained in a natural gas-distillate system. The equilibrium vaporization ratios for the hydrocarbon components in this system had previously been studied by Roland.&apos; In addition to the determination of the K values for carbon dioxide, the K values for methane and ethane were also determined in order to observe what effect, if any, the presence of carbon dioxide had on these K values. The concentration of carbon dioxide was also varied in order to observe the effect of this variable on the carbon dioxide K values. EXPERIMENTAL PROCEDURE The apparatus used in this study cotlsisted of a stainless steel equilibrium cell of about 2 liters capacity. The cell was mounted on trunions permitting rocking in a thermostatically controlled oil bath. Two high pressure valves fitted with steel tubing were mounted on the top of the cell. one was used for sampling the equilibrium gas phase and the other for sampling the equilibrium liquid phase by means of an induction tube within the cell. Stainless steel tubing from the bottom of the cell led to a mercury reservoir and manifold which was connected to a free-piston type pressure gauge manufac- lured by the American Instrunlent Ctr. and to a volumetric. putrip. The temperature of the oil bath was measured by means of a ralibrated mercury-in-glass thermometer. The recorded temperatures are believed to be accurate to ±0.5 °F. The pressures are correct to 22 psi. The crude oil used in this study was stock tank oil obtained from the Wilcox formation in the Billings Field, Noble County. Okla. The natural gas was obtained from the League City Field. Galveston County, Tex. The oil was treated with anhydrous calcium sulfate in order to remove the last traces of water. To insure a supply of constant composition gas at room temperature the cylinders of League City gas were cooled to about 30°F, inverted, and the condensed liquid was allowed to drain from the cylinders. The analysis of the gas and crude are tabulated in Table I. The carbon dioxide came from Pure Carbonic, Inc., and was .stated to have a purity of 99.5 per cent or better. The procedure used to obtain samples of the equilibrium liquid and vapor was similar to that employed by others making use of the rocking type equilibrium cell.6,7,8 The equilibrium cell was evacuated and calculated quantities of carbon dioxide, natural gas, and crude oil were charged to the cell to the desired pressure. In charging the equilibrium cell an attempt was made to maintain the ratio of the natural gas to crude oil as close as possible to that employed by Roland. After the cell was charged, samples of

Jan 1, 1951

By Fred H. Poettmann

The vaporization characteristics of carbon dioxide in a League City natural gas - Billings crude oil system were studied at three temperatures, 38°. 120°, and 202°F and for pressures ranging from 600 to 8,500 psi. Variation of carbon dioxide concentration up to 12 mole per cent in the composite showed no effect on the equilibrium vaporization ratios (K values) of the hydrocarbon constituents or on the K value of carbon dioxide itself. It was shown that carbon dioxide is more soluble in crudes than in distillates which is contrary to the behavior of methane. A working chart of carbon dioxide K values is presented. INTRODUCTION The study of the equilibrium vaporization ratios of mixtures of paraffin hydrocarbons has been rather thorough.2,6,7,8,9 In the past few years considerable attention has been paid to the vaporization characteristics of the so-called noncondensable gases such as nitrogen, carbon dioxide, and hydrogen sulfide in mixtures of hydrocarbons. since they usually occur to some extent in most crude oils and natural gases.1,3,4,5 Knowledge of this behavior is useful to both the production and refining phases of the petroleum industry. This paper reports the equilibrium vaporization ratios (K&apos;s) of carbon dioxide in a mixture of League City natural gas and Billings crude oil, and compares them to those obtained in a natural gas-distillate system. The equilibrium vaporization ratios for the hydrocarbon components in this system had previously been studied by Roland.&apos; In addition to the determination of the K values for carbon dioxide, the K values for methane and ethane were also determined in order to observe what effect, if any, the presence of carbon dioxide had on these K values. The concentration of carbon dioxide was also varied in order to observe the effect of this variable on the carbon dioxide K values. EXPERIMENTAL PROCEDURE The apparatus used in this study cotlsisted of a stainless steel equilibrium cell of about 2 liters capacity. The cell was mounted on trunions permitting rocking in a thermostatically controlled oil bath. Two high pressure valves fitted with steel tubing were mounted on the top of the cell. one was used for sampling the equilibrium gas phase and the other for sampling the equilibrium liquid phase by means of an induction tube within the cell. Stainless steel tubing from the bottom of the cell led to a mercury reservoir and manifold which was connected to a free-piston type pressure gauge manufac- lured by the American Instrunlent Ctr. and to a volumetric. putrip. The temperature of the oil bath was measured by means of a ralibrated mercury-in-glass thermometer. The recorded temperatures are believed to be accurate to ±0.5 °F. The pressures are correct to 22 psi. The crude oil used in this study was stock tank oil obtained from the Wilcox formation in the Billings Field, Noble County. Okla. The natural gas was obtained from the League City Field. Galveston County, Tex. The oil was treated with anhydrous calcium sulfate in order to remove the last traces of water. To insure a supply of constant composition gas at room temperature the cylinders of League City gas were cooled to about 30°F, inverted, and the condensed liquid was allowed to drain from the cylinders. The analysis of the gas and crude are tabulated in Table I. The carbon dioxide came from Pure Carbonic, Inc., and was .stated to have a purity of 99.5 per cent or better. The procedure used to obtain samples of the equilibrium liquid and vapor was similar to that employed by others making use of the rocking type equilibrium cell.6,7,8 The equilibrium cell was evacuated and calculated quantities of carbon dioxide, natural gas, and crude oil were charged to the cell to the desired pressure. In charging the equilibrium cell an attempt was made to maintain the ratio of the natural gas to crude oil as close as possible to that employed by Roland. After the cell was charged, samples of

Jan 1, 1951

By Michel T. Halbouty

The area for which oil and gas development is reported for 1938 in this paper is larger than that covered by the report for 1937, in that besides Duval, Jim Hogg, McMullen, Starr, Webb and Zapata Counties, comprising the Laredo district, this paper also includes the South Corpus Christi district, which is composed of the following counties: San Patricio, Nueces, Jim Wells, Kleberg, Kenedy, Brooks, Willacy, Hidalgo and Cameron, all heretofore included in A.I.M.E. Gulf Coast reports. In the map, Fig. 1, the area known as South Texas is represented by the counties south of the heavy black line. Production in the South Corpus Christi district, which covers an area that extends inland for 50 miles and follows the coast line, is primarily in zones ranging from the Catahoula, through the Frio sands, into the Vicksburg horizon. General exploration is done mainly with geophysics because in this district production is directly dependent upon structural conditions. In the Laredo district most of the production is from sand lenses; therefore, because these shallow sand lenses represent old shore lines which are monoclinic in character, the most satisfactory method of exploration in the Laredo district is drilling. This type of production centers around Duval County and follows a northeast-southwest trend along the Mirando district. Although drilling operations showed a decline from the preceding year, 1938 was highly successful as far as new discoveries and developments were concerned, and results of the year&apos;s operations should have an important effect on the near future trend of exploration and drilling. Besides the discovery of several new fields and many new sands in established fields, 1938 saw the discovery of a new Vicksburg sand trend and the first marine drilling off the South Texas Gulf Coast. Many new fields were discovered during the year, but only a few were subjected to an extensive drilling program. Several already established fields, especially in the Laredo district, received a large amount of drilling as new sands and extensions enlarged the producing areas, a

Jan 1, 1939

By Michel T. Halbouty

The area for which oil and gas development is reported for 1938 in this paper is larger than that covered by the report for 1937, in that besides Duval, Jim Hogg, McMullen, Starr, Webb and Zapata Counties, comprising the Laredo district, this paper also includes the South Corpus Christi district, which is composed of the following counties: San Patricio, Nueces, Jim Wells, Kleberg, Kenedy, Brooks, Willacy, Hidalgo and Cameron, all heretofore included in A.I.M.E. Gulf Coast reports. In the map, Fig. 1, the area known as South Texas is represented by the counties south of the heavy black line. Production in the South Corpus Christi district, which covers an area that extends inland for 50 miles and follows the coast line, is primarily in zones ranging from the Catahoula, through the Frio sands, into the Vicksburg horizon. General exploration is done mainly with geophysics because in this district production is directly dependent upon structural conditions. In the Laredo district most of the production is from sand lenses; therefore, because these shallow sand lenses represent old shore lines which are monoclinic in character, the most satisfactory method of exploration in the Laredo district is drilling. This type of production centers around Duval County and follows a northeast-southwest trend along the Mirando district. Although drilling operations showed a decline from the preceding year, 1938 was highly successful as far as new discoveries and developments were concerned, and results of the year&apos;s operations should have an important effect on the near future trend of exploration and drilling. Besides the discovery of several new fields and many new sands in established fields, 1938 saw the discovery of a new Vicksburg sand trend and the first marine drilling off the South Texas Gulf Coast. Many new fields were discovered during the year, but only a few were subjected to an extensive drilling program. Several already established fields, especially in the Laredo district, received a large amount of drilling as new sands and extensions enlarged the producing areas, a

Jan 1, 1939

By James Norman, E. W. Gieseke

SPODUMENE is a lithium-bearing pyroxene, and is an important source of lithium compounds. Because of its high alumina and lithia content. it might be a desirable constituent of glass batches. The use of spodumene in ceramics will undoubtedly increase, as it has been shown that a mixture of the proper proportions of this mineral with soda feldspar and potash feldspar has a much lower maturing temperature upon firing than has any one of the three components.1 The mineral spodumene seldom occurs as pure mineral, but ordinarily with feldspars, mica and quartz. All spodumene-bearing rocks tested contained these minerals as gangue. Small amounts of iron and manganese oxides also were present, usually as stains on the silicate grains. Mica associated with the spodumene carried a considerable amount of lithia. This was discovered in flotation tailings, which, although virtually free of spodumene grains when examined microscopically, showed 0.4 to 0.5 per cent Li20 on chemical analysis. The lithia content of micas picked from the North Carolina spodumene rock was variable. Some samples contained little lithia, others more than 3 per cent. In 1938, under the supervision of Oliver C. Ralston, [t] the Bureau of Mines, in cooperation with the Tennessee Mineral Products Corporation, undertook to study the beneficiation of North Carolina spodumene by froth flotation. The Bureau had previously published investigations on the beneficiation of spodumene.2, 3 The methods described in the second publication3 did not give good results with badly weathered spodumene rock, so that more thorough investigation of the subject was warranted. STUDY OF METHOD OF FLOTATION SEPARATION Most of the work on concentration of spodumene was done with rock from near King&apos;s Mountain, North Carolina. Rock from two

Jan 1, 1940

By R. L. Segall

AN unusual thermal etch figure in copper is described and an explanation in terms of twinning is suggested. A flat polycrystalline specimen of OFHC copper cut from a rolled sheet was electro-polished in orthophosphoric acid and annealed at 950°C in a vacuum of approximately 10-3 mm Hg for 2 hr. The specimen was found to be thermally etched, the markings on the surface being consistent with the assumption that they were the traces of the (111) planes which are developed preferentially because they have the lowest free energy. However, on one grain (the grain shown in Fig. 1) the traces formed an almost regular pentagon and at first sight it seemed unlikely that they could all be (111) traces. These traces were studied further because it was thought that they might be a type of growth spiral. A fringe pattern showed that this was not so, the grain being sensibly flat and the only features having steps were the striations and the faint curved line passing out from the center of the pentagons. To obtain some additional information, the specimen was deformed in tension. The effect of the stress was first to cause the appearance of lines running from the centers to the apexes of the pentagons and then to tilt the five segments so formed. At a much greater stress, appreciable slip appeared on the grain; these effects can be seen in Fig. 2. The micrograph was taken at a fairly late stage in the deformation and the tilting is quite marked. The magnification is the same as in Fig. 1, and although some slip can be seen it could be observed better by varying the illumination and using higher magnifications. In each segment of the grain, slip (which takes place on the (111) planes) was parallel to the side of the pentagon in that segment. The marked changes in direction of slip from segment to segment seemed to be incompatible with the presence of a regular array of subgrains. These results suggest that some of the five segments were twins. If this is so, since the twinning plane in copper is the (111) plane, the radial lines must be traces of the (111) planes on the surface. From the symmetry of the striations about the radial lines, these planes must be almost perpendicular to the surface. The angle between <III>directions in face-centered-cubic copper is 70&apos;32&apos;. If, in Fig. 3, OAB (triangle 1) is taken as matrix and OA, OB are (111) planes viewed edge on, then AB is in the correct direction to be the trace of either of the other two (111) planes on the surface. If triangle 2 is the twin (about the (111) plane perpendicular to the surface and containing OB) of triangle 1, then once again it can be shown that all lines are traces of (111) planes. Similarly, triangle 3 is the twin of triangle 2, 4 of 3, and 5 of both 4 and 1. (The sequence is, of course, quite arbitrary.) However, if this were the case there would be a discrepancy of 7&apos;20&apos; to be accounted for. It is suggested that the faint curved line passing outward from the center of the pentagon represents either a low angle boundary or a sixth small twin. The slight step shown by the fringes at this line might be an indication that the former is the case. This explanation does not account for the coincidence of obtaining a grain whose surface must be so close to (110) and obtaining the curious twinning described previously; it would be of interest to find a specific mechanism for this.

Jan 1, 1958