Search Documents

By P. Greenfield, C. C. Smith, A. M. Taylor

The Mg-Zr alloy ZA and Mg-Mn alloy AM503(S) are shown to have a markedly improved resistance to creep deformation after suitable heat treatments. This improvement makes them suitable for certain stress-bearing fuel element components in nuclear reactors. The extent of strengthening is described and an explanation of the behavior of both materials is given, based on a combination of strain-aging and grain growth. The increase in operating temperatures of fuel element components in Calder Hall type nuclear reactors has necessitated the development of magnesium base alloys with a very high resistance to creep at temperatures up to 500°C. Such alloys are not required for fuel element cans, which require high-creep ductility rather than strength, but for can supporting and stabilizing components, which are needed to support the imposed loads without deforming more than about 1 pct in times of up to 40,000 hr. The amount and type of alloying addition made to magnesium for these parts is limited by the necessity of keeping the cross-section to thermal neutrons as low as possible. The alloys must also possess a high resistance to oxidation in CO2. Alloys which have been developed for this application include ZA, an alloy of magnesium with 0.5 to 0.7 pct Zr and AM503(S), an alloy of magnesium with 0.5 to 0.75 pct Mn. In the as-extruded condition these alloys are very weak and ductile in creep but it has been found that they can be strengthened to a significant extent by heat treatment. This paper describes the method of developing a high-creep resistance in ZA and AM503(S), the extent of the strengthening produced and discusses the probable mechanisms of strengthening. TEST MATERIALS Specimens were taken from typical casts of ZA and AM503(S) alloys extruded into 2 1/4-in.-diam bars, supplied by Magnesium Elektron Ltd. Typical analyses of the bars were as follows: The as-extruded mean grain diameter was 0.001 to 0.002 in. for the ZA alloy and 0.003 in. for the AM503(S) alloy. EXPERIMENTAL METHODS Extruded bars of ZA alloy, 2 1/4 in. in diameter and 9 in. long, were heat treated in electrical resistance furnaces in an atmosphere of flowing CO2 containing 50 to 300 ppm water, thereby reducing the extent of oxidation compared with that which would have occurred in air. Heat treatments were carried out at 600oc for times of 8, 24, 48, 72, and 96 hr and material was subsequently both furnace cooled and water quenched. In order to measure the effect of time of heat treatment, specimens were creep tested at 400°C and 336 psi for about 1000 hr. Subsequently, the behavior of material heat treated for 96 hr at 600°C and furnace cooled was tested at a variety of stresses from 200° to 500°C. Tests were also conducted at 200o and 400°C on material in the as-extruded condition for comparative purposes. With the AM503(S) alloy, only the effect of heat treatment at 565°C for 4 hr was examined. It has been shown1 that such a heat treatment produces marked strengthening in this alloy. Tests on this material were conducted at a variety of stresses at 200°, 300°, and 400oc with comparative tests on as-extruded material at 200o and 400°C. The creep tests were carried out on machines using dead-weight loading and direct micrometer strain measurements on specimens 5 in. long and 0.357 in. diameter. At temperatures of 400° C and below, the creep tests were conducted in air, but at higher temperatures an atmosphere of CO2 was used. Grain size measurements were made on ZA in the extruded and heat treated states and on each specimen after creep testing. This was done by a line count of a minimum of 20 grains in two or three random fields in the longitudinal and transverse directions. The same method was used for measuring the grain size of as-extruded AM503(S), but the grain size of the heat treated material was so large that this method could not be employed. For heat-treated AM503(S) the large grained characteristics (between 0.1 and 1 in.) were confirmed by the measurement of individual grains. In the case of the ZA alloy, specimens taken from various stages in the program were analysed for hydrogen by a combustion method. Material in various states was also analysed for the soluble and insoluble zirconium content by dissolving in dilute hydrochloric acid. This technique has been useda for the determination of amounts of zirconium present

Jan 1, 1962

By Robert W. Hunt

(Cleveland meeting, October, 1912.) PERHAPS of all the scientific economic questions which have been claiming the attention of capitalists, metallurgists, manu-facturers, directors of public utilities, and the general public of America, during the last few years, none have been of more importance than the one relating to the wear and safety of steel rails. The discovery of the Bessemer process made possible modern railway development. In that growth, as has generally happened in all progressive movements, ill its department have not remained equally balanced. Iron rails permitted the construction of roadways for the passage of power-driven vehicles. In time the speed and weight of such carriages proved too much for the wearing-qualities of the rails, and the limit of railway capacity seemed to have been reached. Bessemer made his invention, which was soon perfected and developed, especially as related to steel rails, and thereby increased the limit of capacity, acid vastly greater railway progress was, made possible. The Siemens-Martin open-hearth process followed, and was later supplemented by the Thomas-Gilchrist basic improvement. For a time the Bessemer steel rails of commerce Were, more than equal to all that was asked of them, but this did not long continue, as evidenced by the records in our Transactions. Revolutionary changes occurred in the industrial world, and in no part of it more than in steel-rail manufacture. Great and powerful commercial combinations were made, whose financial resources made possible the supplanting of the then most efficient blast-furnaces, steel-works, mid mills, by others of theretofore unimagined capacity. Old traditions and practices of steel-making were wiped away, and, in too many cases, output was apparently the chief aim, with the result that much dissatisfaction with the wear and safety of rails was felt by railway officials, and the general public was concerned as to its safety when traveling. The climatic conditions of the winter

Dec 1, 1912

By R. W. Ph. D. Raymond, Anton Filers, O. H. Hahn

THIS paper will treat of such works only as beneficiate ores directly in the mining districts. And when it is said that more than twenty furnaces exist in Utah, about as many in Nevada, five in Montana, and four in Cerro Gordo, Inyo County, California, it is obvious that a business so extended deserves attention. Wide apart as these different works are located, they have nevertheless to deal in nearly every case with the same or very similar circumstances and conditions, so that, with very few exceptions, virtually the same system of smelting is followed in all these establishments. This is the so-called method of reduction and precipitation in blast-furnaces. As the principal reasons for the employment of a blast-furnace process are to be considered : the low percentage of lead in the ores, the high price of the only available fuel, charcoal, and the exorbitant rates demanded for labor. The reasons why the reduction and precipitation process is preferred to a roasting, reduction, and precipitation process are the high prices of labor and materials, and the preponderance of oxidized ores over sulphurets, though in some cases the latter are quite abundant. The weight of these reasons will be better understood when the character of the ores to be treated and the object of the smelting are more minutely stated. The ores are in nearly all cases a preponderating mass of oxidized lead ores, such as cerussite, anglesite, and leadhillite, in which nests and nodules of undecomposed galena occur. Associated with these are : in Eureka, Nevada, arseniate of iron and arsenical pyrites, hydrated oxide of iron, quartz, and calcareous clay ; in Little Cottonwood Canyon and American Fork, Utah, iron oxide, and in some cases a combination of antimony, the nature of which I have not ascertained; also dolomite and quartz in widely varying proportions; in Bingham Canyon, Utah, only quartz and comparatively little oxide of iron, or iron sulphurets; in Cerro Gordo, California, oxide of iron, iron pyrites, antimonial compounds, copper ores, and, as gangue, carbonate of lime and quartz. In Argenta, Montana, occur, besides the above-named lead ores, pyromorphite, and molybdate of lead. The preponderating gangue of the Argenta ores is quartz, and there is here a larger proportion of galena than elsewhere in the West. In most of the localities named, the lead ores themselves contain sufficient silver to render its separation from the ore the main object of the smelting; but in some of the districts, and especially in Montana, the lead ores serve only to furnish the extracting agent for the silver of true quartzose silver ores, which at the same time contain a sufficient percentage of lead to make amalgamation impracticable. They are therefore beneficiated by smelting, although the lead itself has no market value.

Jan 1, 1873

By R. I. Jaffee, F. C. Holden, H. R. Ogden

The effects of grain size and shape on alloys of titanium with nitrogen and aluminum have been determined. Increasing a grain size decreases strength and hardness and increases impact resistance. Quenching from the ß field produces subgrain markings delineating a plates in Ti-N alloys but not in Ti-AI alloys. This suggests a precipitation from the high nitrogen alloys. ALPHA titanium alloys are single-phase alloys with the hexagonal-close-packed structure of a titanium. If these alloys are worked and annealed within the a field, equiaxed structures result in which strength is derived from the solid solution of the alloying elements present. Strain hardening can be used to increase further the strength of a titanium alloys. This is the only other mode of strengthening the a type of alloy. Quenching from the ß field has been noted by many investigators to have little effect on the strength of iodide titanium and on commercial titanium. Ti-A1 alloys were found to be little different in hardness, whether annealed in the a field or quenched from the ß field.' These facts illustrate a characteristic of a titanium alloys: they are insensitive to heat treatments from the ß field. Underlying this heat-treatment insensitivity are the facts that the a-ß field is generally narrow in a titanium alloys, the transformation-temperature range increases with a-stabilizing content, and the a solubilities of the alloying elements are greater than the ß solubilities. When quenching is done from the ß field, there is no supersaturation of the alloying elements in the acicular transformation structure produced. Welds in a titanium alloys generally are ductile, because no transformation hardening occurs during cooling.1,2 Other desirable features of a alloys are: no thermal-stability problem, excellent toughness, and retention of strength at elevated temperatures better than a-ß or ß alloys of comparable room-temperature strength. The prime factors governing the properties of a titanium alloys are the amount and kind of solute present. This can change the a phase from a soft, tough material into a hard, brittle material with no apparent change in microstructure. Moreover, brit-tleness can exist over a wider alloy-content range, without change of phase, than in most other metals. The solutes for a titanium may be divided into interstitial and substitutional types. Oxygen and nitrogen dissolve interstitially in rather large amounts, extending well through the brittle range, and the transformation-temverature ranges are raised in the process.:' , carbon has a maximum interstitial solubility of about 0.5 pct at the peritectoid temperature, while at lower temperatures the solubility decreases to about 0.2 pct.3,5 Substitutional a solutes include aluminum and tin. Aluminum has a high a solubility of 25 pct Al, and increases the transformation-temperature range markedly.6,7 Tin has a high a solubility of about 20 pct, but has a relatively innocuous effect on the transformation-temperature range.' The choice between interstitial and substitutional solutes generally has been conceded to the substitutional solutes because of a belief that they do not have as adverse an effect on ductility and notch toughness. However, a recent investigation8 on the effect of hydrogen on titanium has shown that this element, which is not under compositional control, has a powerful detrimental effect on notch toughness. Hydrogen was shown to form a hydride which is practically insoluble (about 0.002 pct) in a titanium at room temperature, although the solubility at the eutectoid temperature of about 300°C is relatively high, about 0.16 pct. Limited data were presented on the effect of hydrogen on a alloys, where the same impairment of toughness as in unalloyed titanium is found. The work reported here describes the effects of interstitial and substitutional solutes on 1—the mechanical properties of high purity titanium free of titanium hydride and 2—the influence of structural variables on these properties. Nitrogen was selected as an example of an interstitial solute with high solubility and aluminum as a substitutional solute with high solubility. All compositions were well within the ductile range, since it was not intended to study the brittleness problem here, but to study only the factors influencing optimum mechanical properties. Procedures The alloys were prepared from iodide titanium as 1/2 Ib ingots double melted to insure homogeneity.

Jan 1, 1955

By Harmel A. Dawson, Robert A. Wilson

First the basic steps to determine the values present and the minerals involved which are the basis for the metallurgical testing are presented in this paper. Next, choosing the process or processes indicated for treating an ore are discussed. This is followed by the test procedures used, the results of which will indicate amenability to treatment. These test procedures have been developed, used and proven effective in laboratory evaluations relative to plant processing. Special, uncommon processing is beyond the scope of the paper. Evalutation of test results and incorporation into the preliminary and final flow sheet for plant design are discussed. The value of a flow sheet, with material and water balances, to plant design is shown.

Jan 1, 1978

By B. L. Averbach, M. Cohen, C. H. Shih

The isothermal formation of martensite is studied in Fe-Ni-Mn and Fe-Mn-C alloys under conditions where the athermal transformation is completely avoided, there being no martensite present at the beginning of the isothermal reaction. The initial rate of martensite formation is extremely low under these conditions, but it increases greatly as soon as some martensite is formed. It appears that true initial characteristics of the isothermal reaction can be studied only in samples wherein the formation of martensite on cooling is completely eliminated. THE phenomenon of isothermal martensite formation is well established1 -" but the observations have been made in the presence of varying quantities of athermal martensite. Complete avoidance of athermal martensite and the formation of martensite under pure isothermal conditions have been reported by Kurdjumov and Maksimova2 in an Fe-Ni-Mn alloy (23 pct Ni, 3.4 pct Mn, and the balance Fe) and have been confirmed by recent experiments of Cech and Hollomon in a similar alloy. In each case, the isothermal transformation rate was a maximum at the beginning of the transformation and decreased as the reaction proceeded. These initial transformation rates were used by Fisher7 for the confirmation of calculated nucleation rates based on classical nucleation theory extended to include the effect of elastic strain energy. Cech and Hollomon have admitted, however, that up to 3 pct martensite formed on cooling in their samples and thus was present at the initiation of their isothermal runs. In this paper, experiments on similar alloys are described, except that care was taken to remove the incidental martensite developed at the surface prior to the isothermal reaction. It is shown here that the reaction rate at the beginning of the strictly isothermal reaction is very low. As soon as some detectable amount of martensite is produced, the transformation rate increases rapidly but ultimately decreases as the reaction proceeds. When martensite is allowed to form isothermally in the presence of about 2 pct of prior martensite, the apparent initial reaction rate is a maximum and corresponds to the observations of Kurdjumov and Maksimova and Cech and Hollomon. It is evident that the cooperative nature of the martensitic reaction results in a significant stimulating or autocatalytic effect on the isothermal reaction rate. Experimental Procedure The chemical compositions of the alloys used in this investigation are listed in Table I. The Fe-Ni-Mn alloys A and B were melted in an induction furnace, cast into ingots 2 in. diam by 4 in. long, and forged into % in. diam rods. The manganese steel (alloy C) was melted in an arc furnace and cast into ceramic molds 1/4 in. diam by 5 in. long. The rods were sealed in evacuated Vycor tubes and homogenized at 1175" to 1200°C for 50 hr. The long homogenization resulted in some manganese loss from the surface, producing a thin layer of transformed material. This surface layer was removed by grinding and the specimens were then swaged to 0.050 in. diam wire. Measurements of electrical resistance were made with a Kelvin double bridge to follow the course of the martensitic transformation. A small permanent magnet was also useful in scanning an entire specimen for small localized quantities of martensite. This test is almost as sensitive as the electrical resistance method in detecting the presence of martensite (which is ferromagnetic in these alloys) and it was especially useful in deciding whether a specimen was completely free of martensite. The wire specimens (0.050 in. diam by 2.5 in. long) were sealed in evacuated tubes and austenitized for 5 min at 1150°C. The specimens were quenched into water and, unless otherwise stated, stress-relieved for 1 hr at 650 °C in order to induce greater uniformity in the subsequent martensitic transformation. As dem-

Jan 1, 1956

By G. C. Wallick, W. R. Foster, J. G. Savins

A comprehensive review of the salient features of the differentiation method of rheological analysis in Poiseuille flow from its inception circa 1928 is presented. Here no initial assumptions regarding the nature of the function relating rheological parameters to observed kinematical and dynamical parameters are required in the data-analysis process. In contrast, the integration method involves interpreting flow properties in terms of a particular ideal model. It is shown that, although both methods represent modes of solution of the same integral equation, being relatively bias-free, the differentiation method offers a more discriminating procedure for rheological analysis. The application to problems involving plane Poiseuille flow is also described. INTRODUCTION In most instances, the approach to the problem of interpreting the rheological properties of various compositions as they are affected by changes in chemical or physical environment, assaying the characteristics of a particular constituent of a suspension, analyzing flow behavior in terms of interactions between components in a system, to cite but a few examples, has been in terms of what Hersey1 terms the integration method. Briefly, it consists of interpreting flow properties in terms of a particular ideal model. The usual practice of the integration method is to choose a model with a minimum number of parameters because, other things being equal, it is desirable to use the simplest model which will describe the behavior of a real material and yet be mathematically tractable for the requirements of data analysis. This expression is then substituted into an equation which relates observed kinematical and dynamical quantities, such as volume flux Q and pressure gradient ], and angular velocity and torque T, in a capillary and concentric cylinder apparatus, respectively. The rheological parameters appear on integrating, in an expression relating the pairs of observable quantities such as those just given. In many instances a particular model provides a good representation of rheological behavior over a reasonable range of compositional and environmental changes. Just as often, however, it is obvious that the interpretation of rheological changes by the integration method is not providing realistic information about changes in flow behavior. A more general method of interpreting rheological data for a given material is to make no initial assumptions regarding the nature of the function relating rheological parameters to observed kinematical and dynamical quantities, e.g., flow rate and pressure drop in capillary flow or angular velocity and torque in a rotational viscometer. This general method Hersey1 terms the differentia-ation method. Instead of integrating, one differentiates the integral equation with respect to one of the limits, i.e., one of the boundary conditions; the resulting expression contains the same observable quantities just given, their derivatives, and the rheological function evaluated at that boundary. By obtaining these derivatives from experimental data, graphically or by a computer routine, they can be substituted into the differential equation and a graphical form of the function derived. THEORY OF THE DIFFERENTIATION METHOD FOR POISEUILLE-TYPE FLOWS In this introductory paper, two flow cases which are important in viscometry are considered (one for the first time) from the differentiation method of analysis, flow in a cylindrical tube and flow between fixed parallel surfaces of infinite extent, the basic integral equations being formulated in a manner analogous to the way they originally appeared in the literature. In addition, the following ideal conditions will be assumed: (1) an absence of anomalous wall effects, (2) isotropic behavior everywhere, and (3) steady laminar flow conditions. Before proceeding it would seem appropriate to preface the analysis of these flow geometries with the comment that the basic philosophy of the differentiation method could be said to stem directly from the efforts of Herzog and weissenberg2 to indicate systematically the various ways of using

By SAMUEL GOMPERS

THE name engineer makes a very strong appeal to one who appreciates the mechanism underlying the fabric of our civilization. Engineers are scouts of civilization. We send them ahead into the lone 'places-the wilderness, the jungles, the great watery expanses, to build the highways necessary for civilized man. The engineers must deal with Nature, with that mysterious dynamic thing we call "force," with materials. It is their function to direct the human activity necessary to coordinate these forces and material in order to make them serve the needs and aspirations of men. Because of my high conception of the engineering profession I was glad to accept the invitation to address The American Society of Mechanical Engineers to voice my understanding of the possibilities of your work as engineers of industry, and to suggest what seems to me the responsibility of the-engineer to the whole modern industrial system.

Jan 1, 1921

By H. G. Doll

As a continuation of the earlier paper on the general subject of the SP log, a more complete analysis of certain features of the SP log in shaly sands is given. The pseudo-static SP in front of shaly sands is compared, on a theoretical basis, to the static SP in front of clean sands, as a function of the respective amount of shale and sand in the formation, and of the relative resistivities of the shale, of the uncontaminated part of the sand. and of the invaded zone of the sand. As a conclusion, the advantage of using reasonably conduc. tive mud in this case is shown. The discussion is illustrated by field examples. INTRODUCTION The discussion reported in the present paper is based on a theoretical analysis, and not on experiment. The field examples, joined to the text. are shown only as qualitative illustrations of the essential results of this analysis. Although the hypotheses made in the theoretical developments may perhaps be somewhat improved, it seems, nevertheless, that the results obtained account reasonably well for the actual phenomena, and give a fair approximation of their order of magnitude. The paper contains a mathematical analysis of a tri-dimen-sional distribution of potentials and current lines. due to spontaneous electromotive forces arising at the contact of shales and free electrolytes. as a function of the geometry and of the respective resistivities of the different media involved. It is assumed, although this hypothesis is not proven, that the emf's remain the same even if the shale occurs in very thin layers or in dispersed particles. It has already been pointed out 1,2,3 that, all other conditions being the same, the deflection of the SP log in front of a shaly sand is smaller than opposite a clean sand. When the thickness and the conductivity of a clean sand are large enough. the deflection of the SP log reaches a limiting value which is equal to the "static SP" of the clean sand. It is generally convenient to take the static SP of shale as the reference value or "base line." As a consequence, and for the sake of abbreviation, the expression. "static SP of a clean sand," is often used to designate the difference between the static SP of that sand and that of the shales, which difference is a measure of the total electromotive forces involved in the chain mud sand-shale. A similar limiting value is; also observed for the SP deflec-lion opposite a thick shaly sand, but it is smaller. just as if the total electromotive force involved were smaller in that case. This limiting value has been called the "Pseudo-Static SP" of the shaly sand. The static SP of a clean sand depends on the salinity of its connate water with respect to that of the mud, and, to a certain extent. on the differential pressure which controls the electro-filtration potentials, but it does not depend on the resistivity of the sand. On the contrary. the pseudo-static SP of a shaly sand depends not only on the salinity of its connate water and on the differential pressure, but also on the percentage of shale and on the resistivities of the shale, of the uncontaminated part of the sand, and of the zone invaded by the mud filtrate. If the three resistivities above were equal, the pseudo-static SP would be proportional to the percentage of sand in the shaly sand, and its departure from the static SP of a clean sand having the same connate water would simply be proportional to the percentage of shale. In that case, the pseudo-static SP of a shaly sand containing 10 per cent of shale would he 10 per cent less than the static SP of a clean sand. When. however. the sand is. on the average. substantially more resistive than the shale. the percentage of departure of the pseudo-static SP from the static SP of a clean sand is much larger than the percentage of shale. For that reason, the peaks of the SP log opposite shaly sands are systematically of smaller amplitude when the sands are oil-bearing than when they are water-bearing, all other conditions being the same. This feature is observed even when the sand beds are thick. and even when they do not contain a large percentage of shale. All this has already been described in all earlier publication", but mostly in a qualitative way. The present paper will analyze in more detail the action of the local SP currents which are generated inside of the shaly sands, and which are responsible for the abnormally low value of the pseudo-static SP. The quantitative computations have been extended to the general case of thin interbedded layers of sand and shale, where the resistivities of the shale and sand streaks do not have the same value: they are summarized in charts giving values of the pseudo-static SP of a shaly sand as a function of the different parameters involved. DEFINITIONS The static SP of a clean sand has been defined as the potential that would exist in the mud opposite that sand, were the SP current prevented from flowing. Such an ideal condition is represented on Fig. I-A. By analogy, the pseudo-static SP of a shaly sand can be defined as the potential that would exist in the hole, if the circuit shaly sand — surrounding shales — mud column were interrupted by the insulating plugs placed at the boundaries

Jan 1, 1950

By D. J. DeLazaro, W. Rostoker, R. E. Riley, M. Hansen

At very low concentrations, carbon dissolves interstitially in molybdenum resulting in a linear expansion of lattice parameter with increase of carbon in solid solution. Geometrical consideration of the relative size of carbon atom to size of interstice approximately predicts the observed volume expansion. THE element carbon, occurring in molybdenum, either as an unavoidable impurity, or purposely added, markedly affects the mechanical properties of molybdenum. Several investigators1-" have noted the occurrence of molybdenum carbide at the grain boundaries of cast molybdenum, and Fischer and Rengstorff' have shown that this intergranular constituent can induce intergranular brittleness. The appreciable change, with temperature, of the solid solubility of carbon in molybdenum, found by Few and Manning," suggests other important effects upon mechanical properties. Finally the relative atom diameters of carbon and molybdenum (the ratio of atom diameters is 0.59) are indicative, by analogy with iron (ratio of carbon atom diameter to iron atom diameter is 0.65), of a possible interstitial solid solution. If carbon dissolves intersti-tially in molybdenum, anelastic effects and age-hardening effects, similar to those observed in other body-centered cubic metals, could be expected. However, from the work of Sykes, Van Horn, and Tucker," it might be inferred that carbon forms only a substitutional solid solution with molybdenum. These considerations made it desirable to study the effect of carbon on the lattice parameter of molybdenum in greater detail than heretofore. All heat treating was done in a high temperature furnace7 built specifically for heat treatment of molybdenum. The temperatures and times of heat treatment were determined from the a solubility limit for the Mo-C system." These heat treatments were carried out in argon which was purified with respect to N, and H.!0." Purification of the argon was accomplished by passing the argon over hot (750°C) titanium and then through a magnesium perchlorate drying tower. As many as six samples were run concurrently and quenched at different times without interrupting the furnace cycle. Both the purity of the furnace atmosphere and ability to quench samples from any temperature up to 4000 °F were of prime importance in the successful heat treatment of samples for the lattice parameter investigation. Carbon Analysis The Leco Combustion apparatus was used for carbon analysis. This apparatus is capable of an accuracy of & 0.003 pct for a 1 g sample in the range below 0.10 pct. However, it is felt the degree of accuracy is somewhat better than this limit in view of the consistency evident by cross checking a number of determinations. The Battelle Analytical Laboratory consistently reported check results to within k 0.001 pct C. X-ray Measurements The molybdenum wire specimens (20 mils) were carefully filed down to about 12 mils and then etched with nitric acid to 8 mils. Carbon analyses were made on specimens before reduction in size; however, since there was no evidence of surface carburization, it is probable that the carbon was uniformly distributed throughout the sample. The resultant specimens were strain free and small enough to minimize the error in the lattice parameter determinations due to X-ray absorption. Diffraction patterns were obtained with a Debye-Scherrer powder camera 114.59 mm in diam utilizing the Straumanis type asymmetrical film mounting. Nickel-filtered copper. Ka radiation and zirconium-filtered molybdenum Ka radiation were used. Line positions on the film were measured with a traveling microscope equipped with a vernier scale permitting measurement to 0.001 cm. The average of five readings was used to determine the position of each line. The lattice parameter for each specimen was determined from the data by the extrapolation method of Bradley and Jay, Y.e., the intercept at 90" of the straight line obtained by plotting the apparent lat-

Jan 1, 1953

THIS chapter and Chapter 19 deal with the heat quantities involved in open-hearth steelmaking, including the thermal efficiency of the furnace as a generator of high-temperature heat, the heat storage in the steel and slag produced and in the furnace walls, and the heats of the various chemical reactions involved in combustion, in the formation of slag, and the refining of steel. The fundamental laws to be considered are the first two laws of thermodynamics as applied to problems involving sensible and potential (or latent) heat only: 1. Heat input equals heat outflow plus storage. 2. Heat may be transferred only from a hotter body to a colder one. The first of these laws relates to the various heat quantities or the heat balance of the process. No one has as yet made an open-hearth heat balance that came out almost exactly balanced. The cause probably lies in the difficulties of accurate temperature and flow-rate measurements at the high temperatures involved and the inherent complexities in flow distribution and air leakage present in any real open-hearth furnace system. Some idea of the magnitude of the heat quantities involved can be obtained by a brief, crude outline of the heat balance of a 90-ton heat of steel. We will assume a 60 to 70 per cent hot- metal charge in a fairly fast working and only moderately efficient furnace, burning fuel oil, with a fuel consumption of around 4 million Btu per net ton of ingots produced. The time from start of charge to tap is 9 hr. During this period, the oil burned represents 360 million Btu and the sensible heat in the preheated air at the port ends is 117 million Btu, so that the total heat input at the ports is 477 million Btu. Heat stored in the steel and slag at the end of the heat, plus the various amounts absorbed by certain bath reactions, amounts to a total of 195 million Btu, but 120 million of this is supplied by the heat in the hot metal and by various heat-evolving reactions in the bath,

Jan 1, 1951

By H. C. Schultz

CERTAIN local conditions were known to govern in large measure the successful adaptation of liquid-oxygen explosives to the large-scale blasting at Chuquicamata. The wide variation in hardness of the rock at this mine makes necessary the use of several types of explosives. A locally manufactured, relatively cheap black powder is used in blasting the softer waste and capping material, where a thorough displacement breaks the ground sufficiently. Before the introduction of L. 0. X., an ammonia dynamite of about 65 per cent. strength was being used exclusively in the harder underlying orebody, where a strong disruptive as well as a displacement effect is required for breaking the ore. The L. 0. X., as developed for quarry work in the United States, has a practically pure carbon cartridge material, and the explosive has an extremely high rate of detonation, which should therefore cause it to usefully develop its full disruptive effect in hard ground. The individual blasts at Chuquicamata are large, black-powder shots which dislodge masses of rock averaging 250,000 tons each, and dynamite shots which dislodge masses averaging 80,000 tons each. It was desirable, therefore, to attempt to displace with L. 0. X. the faster, higher-cost ammonia dynamite used in the smaller blasts. It was not considered practical to attempt to displace the low-cost black powder with L. 0. X., as estimated costs showed no probable saving if this were accomplished. Since it was desirable to continue shooting relatively large blasts for effective operation, it was recognized that larger storage facilities than had been in use would be needed for the liquid oxygen. Because of the difficulty of transporting and discharging large storage containers of efficient design, the better plan appeared to be storage and discharge of the liquid at the place of manufacture, and transportation of the filled soaking boxes to the blast.

Jan 1, 1928

By V. W. Aubel

Among the iron-bearing ores of the world, the titaniferous iron sands of New Zealand are probably the least known to American engineers. This is not surprising in view of the fact that American ironmasters look with disfavor on any, even domestic, ores containing over 1 per cent. titanium. The possibilities of smelting titanium-bearing ores in the blast furnace are still undetermined, but the problem of their efficient reduction is becoming more important each year. There seems to be little inclination on the part of American furnace operators to tackle this problem, and they will no doubt continue to utilize the non-titanium ores at their command, leaving research and experiment to those countries not so fortunately endowed. New Zealand has, however, been intensely interested in her deposits of titanium-bearing iron sand, and during the last 50 years considerable English and New Zealand capital has been expended on this problem. The extent of the New Zealand iron-sand deposits is almost beyond measure. From Patea north to Manuka Heads, along almost the entire west coast of the North Island, these deposits exist. Wherever there is beach sand along this 300 mi. of coast line, the sand is iron bearing. It varies considerably in grade; but wherever the contour of the coast affords small bays and inlets, large dunes are found that are remarkably uniform in quality. Several of these large deposits, especially those at New Plymouth and Patea, are noted for their high iron content. The dune at New Plymouth runs between 55 and 60 per cent. of metallic iron; the panning action of the prevailing westerly winds and northwesterly currents has no doubt resulted in this concentration. Whatever the origin of this material may be, there is no doubt that deposition is going on continuously. At New Plymouth, a small artificial harbor, protected from the drifting sand by a large breakwall, has been dredged. Here sailing vessels have for years been loaded with iron sand for ballast by means of a crane and grab bucket operated from the wall of the breakwater. Thousands of tons of sand have been removed from this spot yet each succeeding storm renews the supply. The sand dune shown in Fig. 1 has been tested to a depth of 50 ft. (15 m.) without losing its

Jan 1, 1920

By A. S. Adams

A GLANCE at the list of papers1 that have been published since 1920 on the general subject of flotation suggests the variety of ideas that exist regarding the underlying cause of the phenomenon. Among these ideas, we find several coherent theories, but none that adequately and completely explain the phenomenon. Ralston2 and Bains3 suggested an electrical theory which has to do with the attachment of mineral particles to a bubble by the attraction of unlike electrical charges. This theory has its root in the fact that a bubble of air in pure water is electrified in such a way that the surface is negatively charged while the body of the water is positively charged. This result, which was first discussed by Helmholtz, also obtains when the water contains anything except a high concentration of hydrogen ions, or ions which are trivalent or tetravalent. The theory also holds that the mineral particles have positive charges on their surfaces, and so there is attachment between bubble surface and mineral particles by the old law of electrostatics, which states that unlike charges attract.

Jan 1, 1928

By F. P. Dewey

The subject of this paper does not embrace the consideration of ways and means for the increase of analytical accuracy, or the question what could or should be attained in that direction. I desire simply to call attention to the degree of accuracy exhibited in actual every-day practice. In estimating this, little weight will be given to the evidence afforded by the agreement of duplicate or multiple determinations by the same chemist; for I am convinced that such agreement is a delusion and a snare. Nor will special importance be attached to the agreement of two or even three analyses in special cases, or to the agreement between two methods practiced by the same analyst. I propose to compare the results obtained by several chemists, working upon the same sample and by various methods, in order to exhibit, as I have said, the actual condition of practice. The available material for illustrating this phase of the question is unfortunately scanty; but something has been done; and I hope, by calling attention to some of the work in this line, to stimulate further work in the same direction by inducing others to prepare suitable samples and submit them to various chemists who are competent and willing to make the necessary determinations, and fully describe the methods they employ. I draw most of my illustrations from the Transactions of the Institute, the Proceedings of the Association of Official Agricultural Chemists, and from personal experience. Manganese in Steel.—In May, 1881, Mr. William Kent presented a paper to the Institute entitled " Manganese Deter-

Jan 1, 1897

By Herbert H. Kellogg

Deposits of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine ( — 325-mesh) sand assaying 95.5 per cent SiO2, and a very fine (—3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. Experimental Procedure The Sample.—The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotalion Feed.—By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine frac- . tion was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper. A size separation of this type can be

Jan 1, 1948

By Herbert H. Kellogg

Deposits of high-silica kaolinite clays occur at many places in central Pennsylvania. These white clays were formed apparently by weathering of argillaceous quartzite and limestone. Their geology, distribution and use have been reported by Leighton.1 The larger deposits have been mined from time to time, and the clay, after washing to remove coarse sand, has found use as rubber filler, foundry clay, and in white cements. In general, the clay from these deposits contains too much grit (quartz) to be useful as paper filler, and the silica content is too high to make it useful as china clay for ceramic ware. Gravity methods for the separation of quartz from these clays have failed because of the extremely fine size of the quartz grains, but by the methods of froth flotation described in this paper these sandy kaolins can be made to yield a purified kaolinite that has a chemical composition close to that of good-grade Georgia kaolins, and is free enough from grit to be used as a paper filler. As by-products of the separation, a fine ( — 325-mesh) sand assaying 95.5 per cent SiO2, and a very fine (—3-micron) clay are produced. The possible ceramic uses of these products are being investigated at The Pennsylvania State College. Experimental Procedure The Sample.—The clay sample used in these tests was obtained from a small mine near Tyrone, Pa. It had already been washed to remove coarse sand, and represented the finished product of this small mine and washery. Microscopic examination showed that the clay was composed almost entirely of the minerals quartz and kaolinite, and that the quartz was present mostly in particles larger than one micron, while the kaolinite particles generally were less than 20 microns in size. The kaolinite and quartz particles were physically separable by blunging the clay in water with a suitable dispersant. Preparation of Flotalion Feed.—By the addition of NaOH in an amount equal to 3 lb. per ton of solids, the clay was completely dispersed in water. Flotation feed was prepared by allowing a dispersed suspension (10 per cent solids) of the clay to stand for the period of time required for a 2.5-micron particle of quartz to settle from the top of the container to the bottom. After this settling period the suspension was decanted from the settled solids. The settled solids were redispersed in water and the separation was repeated once. The two fine fractions were then combined. Thus the clay was divided into a fine and a coarse fraction by size separation at approximately 2.5 microns.* The fine frac- . tion was found to have a considerably lower sand content than the raw clay (Table I), and was not treated further. The coarse fraction formed the flotation feed for all the tests described in this paper. A size separation of this type can be

Jan 1, 1948

By Richard W. Smith

THERE are three distinct varieties of phosphate rock, in Tennessee, known commercially as: (a) the "brown" rock, which is the residual pro- duct of the weathering and natural concentration of certain phosphatic Ordovician limestones; (b) the "blue " rock, which is an unaltered phosphatic stratum of Mississippian or Devonian age; and (c) the "white" rock, which is the result of chemical replacement and deposition. Before 1894, South Carolina and Florida had supplied most of the phosphate of the United States, South Carolina leading until that date and Florida from then until the present time. In December, 1893, the blue phosphate of Tennessee was discovered almost simultaneously on Swan Creek, in Lewis County, by two independent parties-by one as the result of a careful and systematic search for a workable deposit of the long known kidney phosphate, and by the other through mistaking it for a "bloom" of coal. Leases were taken and, with further prospecting disclosing other deposits in the region, the development progressed as rapidly as 'could be expected without railroad transportation

Jan 1, 1924

By C. A. Rowland, M. D. Flavel

There are seven basic comminution circuits that can be used to prepare beneficiation feed from the product of a primary crusher. This paper gives a comparison of these circuits based on average process and economical data. The paper is principally devoted to a discussion of the test work required to obtain the process data needed to evaluate each circuit. The results of the test work in conjunction with geographic and economic factors can be used to narrow down the choice of possible circuits to one, two, or three before making a detailed engineering study.

Jan 1, 1985

By W. Rostoker, R. F. Domagala, R. P. Elliott

The phase equilibria of the Hg-Th system over the composition range 0-100 pct Th and temperatures up to 1000°C have been studied for a small-volume, closed system. The solubility of Th in liquid Hg is about 5 pct at 300°C and decreases sharply with decreasing temperature. Two intermediate phases occur, Hg3 Th and HgTh. The structures of these are hexagonal (nonideally close-packed) and face-centered cubic, respectively. The HgTh phase decomposes eutectoidally at 400°-500°C. The solubility of Hg in solid thorium seems to be negligible. AFULL-phase diagram for this system would have to be defined on temperature-composition-pressure co-ordinates. This paper describes the pseudo phase diagram of a closed system, that is, where the alloy enclosed in a small volume equilibrates with a vapor pressure of mercury dictated by composition and temperature. Because of the experimental difficulties in studying a system of this nature, many of the phase relations can only be sketched. Alloy Preparation Alloys over the full range of composition were made from triple distilled mercury and one of two grades of thorium. For the bulk of the work, a calcium-reduced metal in sintered pellet form of reported 99+ pct total thorium content was used. Arc-melted specimens of this thorium gave a hardness of 135 VPN. The microstructure showed small primary dendrites of ThO2. A number of alloy compositions were made with a high-purity, iodide-decomposition thorium metal. The are-melted hardness of a button of this material was 35 VPN. Although the microstructure of the arc-melted specimens showed no dendrites of ThO2, there was definite evidence of an unidentified phase enveloping the grain bound-aries. There were no distinguishable differences between the constitution of alloys made with the two grades of thorium metal. Under normal conditions thorium is not wetted by liquid mercury. The film of ThO2 on all thorium metal cannot be penetrated by either liquid or vaporous mercury. It was therefore necessary to comminute thorium in the presence of mercury under such conditions that oxide films could not reform on the newly exposed metal surfaces. This was accomplished by the use of a high-speed, carbide-tipped rotary cutter incorporated in a chamber purged with argon and connected at the bottom to a demountable Vycor bulb containing a weighed amount of mercury. This experimental device is fully described in a separate paper.1 Alloy compositions were calculated by weighing the empty bulb, the bulb containing the mercury, and the bulb containing the mercury and the thorium chips. Many alloys were analyzed chemically for thorium and/or mercury after subsequent homogenization; the agreement between analyzed and calculated compositions was invariably very close. Bulbs containing the requisite amounts of mercury and fine thorium chips were clamped off, removed to a sealing unit, evacuated and sealed. Amalgamation under these conditions proceeded rapidly even at room temperature. To insure homogeneity, the specimens were annealed to 300-400°C. Alloys containing less than 30 pct Th remained pasty after all treatments, indicating an equilibrium condition of liquid plus solid. Alloys with more than 30 pct Th were transformed into a dark powdery product. These latter specimens were annealed for times of up to 1 week to complete interdiffusion. Many of the alloy compositions are pyrophoric. On exposure to air they oxidize with considerable evolution of heat to a mixture of ThO2 and free mercury. It was mandatory that alloy specimens be handled in a "dry box" purged thoroughly with argon. All X-ray diffraction specimens were powdered, screened, and sealed in capillary tubes within the dry box. Experimental Procedures Thermal analysis experiments, useful only in the mercury-rich region of the system, were conducted with the alloys in their original containers. A reentrant thermocouple well formed an integral part of the bulb. These bulbs were heated in a silicone oil bath and cooled in a dry ice-acetone mixture. The rates of heating and cooling were slowed by immersing the specimen bulb in a larger tube containing silicone oil. This provided a suitable thermal lag. In all tests, pure mercury was run as a basic standard. While the invariant reaction at about the melting point of mercury was detected by thermal analysis, the heat effect at the liquidus was not sufficient to produce an inflection in the cooling curve. It was necessary to determine the liquidus temperatures at the mercury-rich end of the system by "breaks" in electrical reslstivity versus temperature curves for individual alloys. The apparatus for this purpose consisted of a pyrex tube about 2 in. diam and 12 in

Jan 1, 1959