Search Documents

By P. F. Gnirk, J. B. Cheatham

An experimental investigation has been made to study the effects of tooth angle and confining pressure on the force required for indentation of dry rock samples under confining pressure. In these experiments static single-tooth indentations were made on two standstones, a limestone, a schist and a slate under confining pressures of 5,000 to 15,000 psi. Sharp wedge-shaped teeth with included angles ranging from 30°to 105°were used. In all cases the force-displarenzent curves are approxinlately linear for rocks tested under confining pressure, as contrmted with the discontinuous curves obtained for silnilar rocks at atmospheric conditions. Photonzicrographs of thin sections through the craters indicate very little evidence of chip formation during indentation. In general the experimental data lie between calculated values for perfectly rough and perfectly smooth tooth-rock interfaces. INTRODUCTION The variables associated with ctrilling at depth are numerous and, in many instances, are not easity isolated and controlled. Also, many of these variables are interdependent; however, if the variables which are sufficiently independent of each other are held constant and are appropriately introduced, the dependent variables can be more easily studied and evaluated. It is the purpose of the present investigation to study experimentally the simplest case of bit tooth-rock interaction. In essence, the experiments have involved the static loading of sharp wedge-shaped tools on the surfaces of effectively semi-infinite dry rock samples subjected to confining pressures. During this investigation the following quantities have been maintained constant: 1. Pore pressure: atmospheric (i.e., the rock is dry). 2. permeability: although the rocks may be permeable, they are "jacketed" in such a manner that the fluid is not permitted to flow through them. 3. Temperature: 75F. 4. Rate of loading: essentially static (approximately 0.002 in./second). 5. Bit tooth: a sharp wedge-shaped tooth loaded normal to the rock surface. 6. Rock surface: smooth and flat. 7. Drilling fluid: hydraulic oil. In addition to the above conditions, the rock surface was free of a layer of cuttings. There was no indexing to previously indented surfaces, and the influence of corners of the borehole was neglected because the rock samples were effectively semi-infinite. The following quantities have been varied, and the resulting effects have been studied: 1. Rock a) Type (e.g., limestone, sandstone, etc.). b) Mechanical properties ) Necessarily dependent c) Porosity on type of rock. 2. Bit tooth (included angle of wedge-shaped tooth). 3. Depth of penetration. 4. cobfining pressure. On the basis of laboratory experiments which have shown that many rocks exhibit ductile behavior at confining pressures corresponding to depths usually reached during drilling,'.' a theory has previously been advanced which predicts the force required for penetration by a single sharp wedge tooth into a ductile* material.' The material is assumed to be isotropic, homogeneous and rigidly plastic (no elastic deformation) and to obey the Coubomb yield criterion (Figs. 1 and 2). Equations governing the force required for penelration are given for two extreme cases:** 1. A smooth, perfectly lubricated tooth-rock interface (fridionless boundary), in which the solution gives a minimum value for the penetrating force: in which F = force of the tooth, b = length of tooth edge,

By W. A. West

One who attempts to collect and classify equilibrium data from various iron-alloy systems is soon struck with the absence of any quantitative theory that can serve as a general background against which to compare and contrast results from different systems, at different temperatures, and with different concentrations. It is not necessary to wait for a perfect theory; investigation of divergences of theory from observation may prove of great value in acquiring understanding of the subject. For example, one has only to think of Raoult's law as applied to aqueous solutions. The equations developed by Zener1 represent an effort to provide such a quantitative theoretical background, and it is therefore desirable to subject this theory to such tests as can be applied. The present article is intended to be an application of available tests, and may thus be considered as a supplement to Zener's paper. It is assumed that this paper is available to the reader. The equations make it possible to calculate the effect on the equilibrium concentration of one alloying element due to the presence of one or more other elements. In particular. they are intended to give, for alloy steels, the carbon concentrations in alpha and gamma phases in equilibrium with each other, and in gamma in equilibrium with cementite. They may, however, be modified for use for carbon-free alloys. A summary is given later of the equations used in analyzing the data in this paper, and the symbols are there defined. About 125 papers have been examined for experimental data suitable for this investigation. An effort was made to look up all available reports of ternary systems including iron and carbon, as well as similar systems of higher order. Supplementary material was also obtained from a number of binary systems. A few noncarbon ternary systems were also found to which these methods could be applied. A comparatively small proportion oi the papers read provided usable material. In many systems the number of quantitative observations made in the iron-rich region is extremely small, and the smoothed curves to be found in most published phase diagrams are entirely useless for quantitative treatment. This opinion is confirmed by the authors of the series on Alloys of Iron Research, whose remarks show clearly that they have no illusions as to the accuracy of many diagrams that they present. A further difficulty arises from the fact that these equations apply only to rather low percentages of alloying elements. The result is that at the lowest concentrations, where the best agreement might be hoped for, the errors of observation become relatively very large. The experimental difficulties in measurements of this kind of equilibrium are, of course, an old story.

Jan 1, 1947

By W. A. West

One who attempts to collect and classify equilibrium data from various iron-alloy systems is soon struck with the absence of any quantitative theory that can serve as a general background against which to compare and contrast results from different systems, at different temperatures, and with different concentrations. It is not necessary to wait for a perfect theory; investigation of divergences of theory from observation may prove of great value in acquiring understanding of the subject. For example, one has only to think of Raoult's law as applied to aqueous solutions. The equations developed by Zener1 represent an effort to provide such a quantitative theoretical background, and it is therefore desirable to subject this theory to such tests as can be applied. The present article is intended to be an application of available tests, and may thus be considered as a supplement to Zener's paper. It is assumed that this paper is available to the reader. The equations make it possible to calculate the effect on the equilibrium concentration of one alloying element due to the presence of one or more other elements. In particular. they are intended to give, for alloy steels, the carbon concentrations in alpha and gamma phases in equilibrium with each other, and in gamma in equilibrium with cementite. They may, however, be modified for use for carbon-free alloys. A summary is given later of the equations used in analyzing the data in this paper, and the symbols are there defined. About 125 papers have been examined for experimental data suitable for this investigation. An effort was made to look up all available reports of ternary systems including iron and carbon, as well as similar systems of higher order. Supplementary material was also obtained from a number of binary systems. A few noncarbon ternary systems were also found to which these methods could be applied. A comparatively small proportion oi the papers read provided usable material. In many systems the number of quantitative observations made in the iron-rich region is extremely small, and the smoothed curves to be found in most published phase diagrams are entirely useless for quantitative treatment. This opinion is confirmed by the authors of the series on Alloys of Iron Research, whose remarks show clearly that they have no illusions as to the accuracy of many diagrams that they present. A further difficulty arises from the fact that these equations apply only to rather low percentages of alloying elements. The result is that at the lowest concentrations, where the best agreement might be hoped for, the errors of observation become relatively very large. The experimental difficulties in measurements of this kind of equilibrium are, of course, an old story.

Jan 1, 1947

By R. L. Ash, R. R. Rollins, C. J. Konya

An investigation was performed to determine conditions for optimizing the spacing of simultaneously initiated multiple explosive columns. This was done by using models of mortar, dolomite, and Plexiglas with 10-grain mild detonating fuse as the explosive charge. It was desired to simulate blastholes with multiple primers initiated by detonating fuse or when high-velocity explosives are used in low-velocity materials. It was found that optimum spacing between multiple charges was strongly influenced by charge length. At less than optimum charge length, the spacing at which complete shearing was possible between adjacent charges decreased exponentially with a subsequent loss of broken material volume. For charges fired simultaneously, larger burdens and spacings were possible as compared to those necessary for single-crater charges. For each material studied, there was a characteristic optimum charge length and a maximum attainable spacing at any given burden. Proper selection of the spacing distance between charges is fundamental to successful blasting. Its value directly affects the cost of drilling and explosives used per unit of broken material. In addition, the choice of a spacing that is Compatible with a given set of blasting conditions aids in the control of fragmentation sizing, ground vibrations, overbreak, and throw which in turn, influence other production costs. For example, normally loaded blastholes that are spaced too closely invariably promote overbreak and usually give coarse fragmentation. Unless care is taken, airblast and violent flyrock will occur and under certain conditions cutoffs and misfires may result. Too large a spacing, on the other hand, frequently leads to conditions that form bootlegs or toes. The choice of a particular spacicg to use, however, is largely a matter of individual experience and judgment, usually based on trial and error. Very little is known or can be found in the literature with regard to how the spacing between charges is related to field conditions and charge geometry. As a general rule, the firing time sequence of adjacent charges and properties of a material are thought to have the most significant influence on the spacing distance best suited for any given field condition. For example, delayed initiation of adjacent charges usually always requires a closer spacing than when charges are fired at the same time. This should be expected if one considers that the energy normally dissipated and lost in the surrounding ground from charges fired independently would be captured and utilized for breaking material between charges when they are initiated together. Spacing can be extended also when charges are aligned with structural planes of a material, such as jointing, along which shearing is relatively easy. It is customary to relate the spacing (S) between charges to their common burden (B) in the form of a spacing ratio, or SIB. The burden normally is considered as the optimum depth or distance from any single charge perpendicular to the nearest free or open face at which the desired fragmentation and maximum crater yield are obtained. For production blasting, value of the ratio is generally considered to vary from 1 to 2, depending on conditions.1-6 When adjacent charges are fired independent of one another, the value varies from 1 to about 1.4, the closer amount being employed to square corners or produce craters having the ideal 90" apex angle. The larger ratio is the geometric balance value for craters having an apex angle of 135". The basic ideal crater forms in the plane of the charge diameter for charges fired independently are shown in Fig. 1. In the event charges are fired simultaneously, geometric balance in the plane of their charge diameters suggests that a spacing ratio near 2 would be appropriate, as illustrated by Fig. 2. In practice, however, some compromise ratio value must be selected to conform with the specific ground conditions. An example would be where the jointing planes tend to produce 60° or 120° crater angles, the appropriate geometrically balanced charge arrangement being given by Fig. 3. In this condition, the spacing ratio is 1.15, not 1 or 1.4 as suggested for the 90° cratering of independently fired adjacent charges. In view of the foregoing, it would seem logical to assume that whenever charges all having the same burden are fired at the same time, spacing distances always can be greater than those permitted by charges fired independently. In practice this is not the case, however.

Jan 1, 1970

By Peter Soo

Pvestrained Ferrovac E iron has been neutron-irradiated at approximately 90°C to an integrated flux of 1020 nut (E > 0.82 mev]. The irradiation was found to produce an incveased temperature dependence of the flow stress in addition to a greatly increased athemal stress. Measurements of the flow stress and stress relaxation, from which the activation volume and activation energy for slip were deduced, show that neutron irradiation changes the rate -controlling slip process to one based on dislocation interactions with tetragonal distortions which are Produced around submicroscopic interstitial loops in the lattice. The study indicates that without prestraining prior to irradiation the chances of detecting a change in the rate -controlling slip process are greatly reduced because in the initial stages of slip a substantial fraction of the radiation defects are swept out of the slip plane by gliding dislocations. Thus, activation parameters which are subsequently measured are representative of a greatly reduced defect density and would not differ appreciably from those for unirradi-ated material. The large increase in the athermal component of the flow stress is probably connected with the presence of depleted zones in the lattice which are introduced by irradiation. ALTHOUGH fast neutron-irradiation has not been observed to markedly alter the activation parameters for slip in bcc metals,' small but significant changes do occur. Most experimenters agree that irradiation predominantly increases the athermal component of the yield stress.'-= In addition to this, Laidler and smidt7 have shown that in iron irradiated to 5 X 10" nvt and molybdenum irradiated to 10" nvt, changes occur in the activation volumes for slip. A similar conclusion has been reached by Milasin and Malkin8 for irradiated iron. Work by Ohr et a1.5 shows that for Ferrovac E iron, irradiated to 1.2 X 1016 nvt, small increases in the activation energy for slip also occur. So far these changes in the activation parameters have not been explained on a firm theoretical basis. One important factor which would minimize the chances of detecting a change in the slip mechanism upon irradiation is the presence of "channeling" which has been observed in molybdenum,9 niobium,10 and iron.11These channels are formed by gliding dislocations which sweep irradiation defects out of the active slip planes and thereby create zones in which continued dislocation motion is encouraged. The activation parameters for the dislocations gliding in the defect-free channels would, therefore, be similar to those for unirradiated iron and a change in the rate-controlling slip process would be difficult to detect. In the present work, an attempt has been made to reduce the effect of uneven deformation on the measured activation parameters for slip in neutron-irradiated Ferrovac E iron polycrystals, so that a more realistic assessment of the effects of neutron-irradiation could be made. Primarily, the experiments involve the irradiation of specimens which had been prestrained to 9 pct elongation at room temperature prior to insertion into the reactor. It was hoped that the introduction of a large number of evenly distributed dislocations would substantially decrease any channeling effect which might otherwise occur. MATERIAL AND EXPERIMENTAL PROCEDURE The starting material was vacuum-melted Ferrovac E iron, an analysis of which is given in Table I. The standard tensile specimen had a gage length of 1.125 in., a cross-sectional diameter of 0.120 in., and a re-crystallized grain size of 1.2 x 10-3 in. All tensile tests were conducted on a floor model "Instron" tensile machine at a strain rate of 3 x 10-4 per sec. The irradiation of the prestrained specimens was performed in the Brookhaven High Flux Beam Reactor to an integrated flux of 1020 nvt (E > 0.82 mev) at a temperature of about 90°C. All specimens were excap-sulated in high-purity aluminum sheaths which were lightly swaged around the samples to ensure good thermal contact. Subsequent measurements on the irradiated specimens showed that within experimental accuracy the swaging had not deformed them. EXPERIMENTAL RESULTS Fig. 1 shows the flow stresses for a series of unirradiated control samples. In order to produce a comparable dislocation substructure throughout the test sm range, all specimens were prestrained

Jan 1, 1970

By D. R. Hay, E. Scala

Electrotransport has been superimposed on the rate-limiling- step in zone refining which is the impurity diffusion through the liquid at the solid/liquid interface. The efficiency of zone refining is increased and relative resistivity ratios (P300°k/P4 2°K) he increased by 50 pel in tungsten for a given number of posses using- the electrotransport field-aided method. The effiect of zotze refining in the presence of an electric field on the relative resistivity ratio is examined as a function of its intensity and polarity. THE effect of electrodiffusion on the effective distribution coefficient of zone refining has been discussed by Pfann and Wagner.' Control of the distribution coefficient in zone refining is of twofold interest. A distribution coefficient of unity can be increased or decreased, making possible the transfer of some previously inseparable solutes. The general efficiency of zone refining can also be increased. In the conventional zone-refining process impurities are removed by their retention in the molten zone and subsequent deposition at the end of the rod after a complete passage of the zone. In higher-melting-point systems a second mechanism may also operate, the volatilization of impurities from the molten zone. It has been suggested by schadler2 that, in refractory metals, vacuum distillation plays the predominant role in purification. In Koo's results,3 the resistivity ratio decreased beyond a zone-refined length of 6 in. from the starting end, indicating that some purification does in fact occur by true zone-refining action. Hay and scala4 showed that the degree of purity as measured by the relative resistivity ratio method depends on the square root of time in the molten zone (number of passes) and thus appears to be limited by diffusion in the boundary layer at the solidifying interface assuming good mixing in the body of the molten zone where a linear rate would prevail. The final concentration of impurities in electron-beam floating-zone purification depends very much on the operating conditions and results obtained by various investigators2,3,5 are difficult to correlate. The diameter of the starting material, operating vacuum, and rate of traverse are among the factors to be considered. There are, nevertheless, some general observations to be obtained from the literature. Lawley5 reviewed the literature up to 1962 and concluded that the major contaminants generally remaining in tungsten after electron-beam zone refining are molybdenum and carbon. Molybdenum due to its high melting point and distribution coefficient of nearly unity would be expected to be difficult to remove by either volatilization or zone refining. Carbon is not only a common contaminant in vacuum systems, but is also very difficult to remove by conventional vacuum melting. even with vacuums of 10-7 mm Hg. For each of those impurities removed by zone refining the equation of Pfann and Wagner may be applied: It relates the effective distribution coefficient k to a superimposed driving force which accelerates the solute away from the interface with a terminal velocity L" and to the more conventional zone-refining parameters; v = rate of traverse, t = thickness of the diffusion layer at the solidifying interface, D = diffusivity of the solute in the molten zone, and ko = equilibrium distribution coefficient of the impurity.

Jan 1, 1965

By R. Lagneborg, R. Gullberg

An X-ray method for determinig volume fractions of phases in textured materials has been developed. The method involves measurements of the integrated intensities of reflections of each phase for one single orientation of the sample. The method was checked by evaluating the phase contents in samples from two stainless Cr-Ni steels containing austenite and ferrite in known amounts. In the present case measurements of about five reflections from each phase were required. The agreement between calculated and known volume fractions was found to be very close. AN X-ray diffraction method is often employed for determining the amounts of two or more phases in a material. The details of the method have been described at several instances.'" In short, the method is based upon the fact that the integrated intensity of a reflection is directly proportional to the volume fraction of the phase considered. In principle, the method only requires the measurement of the intensity of one reflection for each phase. The most severe shortcoming with this method is that it disregards influences from preferred orientation in the material. In a diffractometer, where this type of analysis is most conveniently carried out, the geometry is such that the diffracting planes for a specific Bragg peak are all parallel to the surface of the specimen. This implies that it must be required that the occurrence of the diffracting planes parallel to the specimen surface must be as frequent as for any arbitrarily oriented physical plane of the sample. This requirement will generally only be fulfilled for a material free of texture. Since all materials in reality always exhibit a preferred orientation to some extent. the deficiency of the method is quite serious. In cold-deformed material the texture is appreciable, but also annealed material will in many cases display a considerable texture. The problem of quantitative phase analysis in textured material is one of obtaining the integrated intensity averaged over all orientations of the specimen with respect to the X-ray beam. Lopata and ~ula~ have shown that this can be accomplished by integration of intensities over the whole pole figure, or by random rotation of the specimen in the X-ray beam, or by a combination of both. Hence, in this method the average integrated intensity for a specific reflection is obtained by directly determining the intensity for a sufficient number of physical orientations of the sample. However, since an excess of diffracting planes in a certain surface plane necessarily must be accompanied by a deficiency of another type of diffracting plane, it appears to be possible to obtain the correct average intensity for a specific diffracting plane by performing an appropriate averaging of intensities belonging to a large number of diffraction planes of different hkl when all intensities have been produced from one single orientation of the specimen surface. In the present work such a method has been attempted and tested experimentally for two stainless Cr-Ni steels containing austenite and ferrite. 1) THEORY The expression for the integrated intensity of a Bragg reflection diffracted from a phase in a polycrys-talline sample in a diffractometer is: where C is a constant only dependent on the incident X-ray power and the diffractometer geometry, v the volume of the unit cell, F the structure factor, m multiplicity of the diffracting plane, L Lorentz factor, P polarization factor, e-2 temperature factor, p average linear absorption coefficient of the irradiated vO1umej and V volume fraction of the phase 'Onsidered. Hence, the factor R in the abbreviated form of Eq. [I] can be calculated and depends only on 0 and the diffracting plane {hkl}. For an alloy containing two phases, a and y, we can write

Jan 1, 1967

By W. A. West

ONE who attempts to collect and classify equilibrium data from various iron-alloy systems is soon struck with the absence of any quantitative theory that can serve as a general background against which to compare and contrast results from different systems, at different temperatures, and with different concentrations. It is not necessary to wait for a perfect theory; investigation of divergences of theory from observation may prove of great value in acquiring understanding of the subject. For example, one has only to think of Raoult's law as applied to aqueous solutions. The equations developed by Zener1 represent an effort to provide such a quantitative theoretical background, and it is therefore desirable to subject this theory to such tests as can be applied. The present article is intended to be an application of available tests, and may thus be considered as a supplement to Zener's paper. It is assumed that this paper is available to the reader. The equations make it possible to calculate the effect on the equilibrium concentration of one alloying element due to the presence of one or more other elements. In particular they are intended to give, for alloy steels, the carbon concentrations in alpha and gamma phases in equilibrium with each other, and in gamma in equilibrium with cementite. They may, however, be modified for use for carbon-free alloys. A summary is given later of the equations used in analyzing the data in this paper, and the symbols are there defined. About 125 papers have been examined for experimental data suitable for this investigation. An effort was made to look up all available reports of ternary systems including iron and carbon, as well as similar systems of higher order. Supplementary material was also obtained from a number of binary systems. A few noncarbon ternary systems were also found to which these methods could be applied. A comparatively small proportion of the papers read provided usable material. In many systems the number of quantitative observations made in the iron-rich region is extremely small, and the smoothed curves to be found in most published phase diagrams are entirely useless for quantitative treatment. This opinion is confirmed by the authors of the series on Alloys of Iron Research, whose remarks show clearly that they have no illusions as to the accuracy of many diagrams that they present. A further difficulty arises from the fact that these equations apply only to rather low percentages of alloying elements. The result is that at the lowest concentrations, where the best agreement might be hoped for, the errors of observation become relatively very large. The experimental difficulties in measurements of this kind of equilibrium are, of course, an old story.

Jan 1, 1946

By J. W. Freeman, E. E. Reynolds, A. E. White

Fram a study of 63 systematic alloy modifications it was found that molybdenum, tungsten, and columbium, added individually or simultaneously, and increases in chromium cause major improvements in 1200°F rupture strengths of Cr-Ni-Co-Fe base alloys. Rupture strengths were a function of the effect of composition modifications on both the inherent creep resistance and the amount of deformation the alloy would tolerate before fracture. THIS paper describes the results of an investigation of a series of alloys with systematic variations of the chemical composition of the following basic alloy: C, 0.15: Mn, 1.7; Si, 0.5; Cr, 20.0; NI, 20.0: Co, 20.0: Mo, 3.0; W, 2.0; Cb, 1.0; N, 0.12; Fe, 32.0 pct. The 62 modifications of this alloy were produced under conditions which minimized all factors influencing properties at high temperatures except composition. Melting, fabrication, and heat treatment were carefully maintained constant. Stress-rupture properties at 1200°F were used as the primary criteria of evaluation of the alloy. The objective of the study was to obtain data for determining the fundamental role of the influence of alloying elements on properties of heat-resistant alloys at high temperatures. In addition the results should be useful in determining optimum chemical compositions, the sensitivity of properties to variations in composition, and the degree to which alloy content could be reduced while retaining worthwhile properties. It is difficult or impossible to develop correlations between properties at high temperatures and systematic variations in chemical composition from published data for wrought heat-resistant alloys developed for gas turbines.' ' The main reason for this is the extreme dependence of the properties on conditions of treatment of the alloys." In most cases variation in final treatments between alloys so influences the properties that the influence of chemical composition is obscured. In addition it is recognized Table I. Basic Alloy and Some Modifications Used Basic AllOy, Variations in Element Pct Composition, Pct C 0.15 0.08. 0.40. 0.60 Mn 1.1 0.03,0.25.0.50,1.0,2.5 S1 0.50 1.2, 1.6 Cr 20.0 10, 30 Ni 20.0 0, 10,30 Co 20.0 0. 10, 30 MO 3.0 0. 1.2.3, 5, 7 W 2.0 0, 1, 5, 1 Cb 1.0 0.2,4,6 N 0.12 0.004, 0.08, 0.18 Fe 32.0 that variations exist between heats of the same alloy which are related to melting practice and that there is a strong possibility that conditions of hot working influence response to final treatments. The development of heat-resistant alloys has been based on the gradual accumulation of data roughly related to composition from extensive testing programs. There is every reason to believe that in most cases the optimum compositions have been achieved by this procedure in the alloys commercially available. There are, however, very little data showing the influence of systematic variations of composition free from the influence of other factors, particularly for alloys of the type investigated. Several investigators of cast alloys have demonstrated compositional effects, notably Grant,1-6 Epremian,t Guy,8 and Harder and Gow.9 Sykes10 eviewed the work on the wrought alloy Rex 78 and the systematic variations of carbon, copper, molybdenum, and cobalt leading to the development of the stronger Rex 337A alloy. From the papers by Wilson11 and Henry12 it is possible to deduce the beneficial effect of substituting cobalt for iron in 0.45 pct C-20 pct Cr-20 pct Ni-4 pct Mo-4 pct W- 4 pct Cb alloys. Wilson mentioned but did not present the extensive compositional studies involved in developing these alloys. Binder" showed optimum properties for 3, 2, and I pct, respectively, for molybdenum, tungsten, and columbium in 20 pct Cr-20 pct Ni-20 pct Co-30 pct Fe alloys for limited systematic variations of these

Jan 1, 1953

By Donald B. Evans, Robert D. Pehlke

The solubility of nilrogen in liquid binary alloys of iron with Litanium. zivconium, columbium, vanndiurn, and tantalum was measured for alloy composiLions up to the solalbility limils of lhe alloy nitrides. All five alloying agents were found to decrease markedly the activity coefficient of nitrogen in liquid ivon. The metal/nitvogen mole ralios in the alloy nitrides formed were generally .found to be slighlly greater than 1.0, but in no case greater than 1.5. From the experimental data, the standard free energies of fortmation of titanium and zir-conium nitrides have been calculated for the Lemperaluve range 1550° to 1750 C. The solublily Products for columbium, tantalum, and vanadium nitrides are also reported. A number of research investigations have examined the effect of refractory metals on the solubility of nitrogen in liquid iron. Although data on zirconium are not available, investigators are in agreement that titanium, vanadium, columbium, and tantalum markedly increase the solubility of nitrogen in liquid iron. This fact alone makes desirable the acquisition of thermodynamic data for these elements in liquid iron. Since refractory metals are known to be stable nitride formers, they have been suggested as steel denitrifying agents, and some of their nitrides have recently been considered as containment materials for liquid iron and iron alloys. Most available thermodynamic data for these metals relate to their dilute concentrations, but effective thermodynamic treatment of these applications requires data at concentrations near the solubility limit of the alloy nitride. Although some work has been done at relatively high alloy concentrations in liquid iron (particularly for vanadium 2,3 and titanium 2,4), the results have been somewhat contradictory. Disagreement may be partly attributed to the fact that the compositions of most refractory metal nitrides have been shown to be nonstoichiometric, and to vary 2,5-8 depending on the temperature and nitrogen gas pressure with which the solid nitride phase is in equilibrium. One purpose of this study consequently has been to determine the compositions of the refractory metal nitrides precipitated from a liquid iron solution. EXPERIMENTAL PROCEDURE Rao and Parlee2 and Evans and Pehlke 9 have discussed the technique for measuring the solubility product of an alloy nitride phase in liquid iron by finding the point of departure of the nitrogen solubility from Sieverts' law. The method consists of measuring the solubility of nitrogen in a melt of iron containing a known concentration of a second metal as a function of the nitrogen gas pressure over the melt. In this study the second metal was one of the refractory metals titanium, zirconium, columbium, vanadium, or tantalum. When the nitrogen pressure at which the refractory nitride forms is reached, a deviation of the measured solubility of nitrogen in the melt from Sieverts' law is observed in the form of a "pressure halt." The concentration of nitrogen in the melt associated with this breakpoint in the nitrogen-absorption curve is then used to calculate the nitride solubility. The Sieverts method was used to measure nitrogen solubility as a function of nitrogen pressure and temperature. The experimental equipment for this technique has been previously described in detail. 1,9 Charge materials used were vacuum-melted high-purity iron (Ferrovac-E) and the best commercial grades of the refractory metals obtainable (in all cases at least 99.8+ pct pure). Recrystallized alumina crucibles were used to hold all melts except those containing zirconium, for which zirconia crucibles were necessary. Temperatures were measured by a disappearing-filament type optical pyrometer sighted vertically downward on the melt surface through a 1/4-in.-diameter sight hole in the crucible lid. By means of a technique previously described, 9 in which the refractory-metal nitride was precipitated at one temperature then redis-solved by raising the temperature 50°C and precipitated again at a higher temperature, it was possible to obtain data over a temperature range of up to 200°C on a single melt. It was found that this technique could not be used with melts containing zir-

Jan 1, 1965

[IRVING, JOHN D. :-(Continued.) Some Features of Replacement Ore-Bodies, and the Criteria by Means of Which They May be Discovered, XLII, [xlvii]. Discussions: on A Concise Method of Showing Ore-Reserves, XLIII, 714; on The Iron Deposits of Daiquiri, Cuba, LIII, 65; I on Recrystallization of Limestone at Igneous Contacts, XLVIII, 214; I on To What Extent is Chalcocite a Primary, and to what Extent a Secondary, Mineral in Ore Deposits, XLVIII, 194. minerals of gold deposits, Homestake belt, Black Hills, S. D., XLII, 54.]

Jan 1, 1918

K. T. Aust and J. W. Rutter (General Electric Research Laboratory)—We find it difficult to reconcile the activation energies determined by Gifkins with his general conclusion that "migration during both creep and grain growth can thus be treated on the basis of the same model" (that of Lucke and Detert). Gifkins finds the activation energy for grain boundary migration during creep to be 24.5 kcal per rnol and that for grain boundary migration during grain growth to be 7.5 kcal per mol. The calculation carried out by Gifkins of the activation energy for grain boundary migration during grain growth, using the Lucke and Detert model, gives a value of 20 to 24.5 kcal per mol, rather than his experimental value of 7.5 kcal per mol. The theory of Lucke and Detert was developed to account for the rates of migration of grain boundaries in the presence of impurities during grain growth. The theory does not take into account the effect on the boundary migration of another, simultaneous process such as creep deformation and would be expected, therefore, to be applicable only to migration during grain growth. The fact that Gifkins measured a different activation energy for boundary migration during grain growth (7.5 kcal per mol) from that during creep (24.5 kcal per mol), although the specimens were of the same composition, shows clearly that such an effect exists under his experimental conditions; the presence of a simultaneous creep deformation markedly affects the boundary migration process in comparison with what would be observed under the same conditions but without the creep deformation. The failure of McLean's equation (Eq. [4] of Gifkins' paper) to give a satisfactory dislocation density difference for boundary migration during creep is not surprising, since the activation energy which must be used in this equation refers only to the elementary atom transfer process of grain boundary migration. This activation energy value is approximately 6 kcal per mol for zone-refined lead, as determined in both the grain boundary migration experiments of Aust and Rutter31, 32 and the grain growth experiments of Bolling and Winegard.33 Using this activation energy value, McLean's equation gives reasonable agreement with observed migration rates for grain boundaries moving free of the influence of impurities.31, 32 The value of 24.5 kcal per mol is probably associated with the presence of impurity atoms, as Gifkins suggests. It should be noted, however, that this value was obtained using lead of only one composition and measurements at only two temperatures. The work of Aust and Rutter3"' on the effects of tin, silver, and gold on grain boundary migration in zone-refined lead in the temperature range from 320" to 200°C, as well as the work of Bolling and Winegard34 on the effect of silver and gold on grain growth in zone-refined lead, shows that the measured activation energy is markedly dependent upon the kind and amount of solute present. Gifkins' work does not permit evaluation of the effect of the 8 ppm of impurities other than oxygen present in his specimens. One incidental point: the symbols used to designate the experimental points of Fig. 6 appear to be in incorrect order in the figure caption. As the caption is printed, it would indicate that larger grain sizes were obtained after annealing at 47°C than at 100°C, which does not agree with the text (point M, p. 1019). Finally, it seems clear from Gifkins' results that any serious attempt to determine whether grain boundary migration and grain boundary sliding during creep occur with the same activation energy, as Gifkins suggests and McLean rejects, must take into account the effects of impurities on these two processes, Although the work of Weinberg35 indicated that adding small amounts of copper, iron and silicon to aluminum did not affect the grain boundary shear behavior, it should be noted that his starting material contained approximately 60 ppm of impurities. Gifkins' results indicate impurity effects at an impurity level of 8 ppm, suggesting strongly that the most significant impurity range to be investigated lies substantially below that value. R. C. Gifkins (author's reply) — As Drs. Aust and Rutter suggest, the results under discussion may have to be reinterpreted in the light of their own work on grain boundary migration, which was not available to me when the paper was written. Because of their work, Aust and Rutter attach more importance than I did to the activation energy for grain boundary migration during annealing (7.5 kcal per mol) obtained from a "direct" plot of log-rate against the reciprocal of absolute temperature. At the time it was obtained, this value seemed rather low, although it was similar to the value obtained by Bolling and Winegard.36 It was then, and still is, difficult to accept this value because of the low value of the index in the power law for grain growth, which seemed to indicate the influence of impurities. It was also concluded that the low value of the activation energy might have arisen from the manner of selecting rates of grain growth which were truly comparable at the two temperatures. There were many other indications in these experiments and those on recrystallization during creep3? that an impurity, probably oxygen, was of importance. The model for grain-boundary migration which Lucke and Detert had proposed was an obvious possibility and its use yielded an activation energy for boundary migration during annealing of 20 to 25 kcal per mol.

Jan 1, 1961

By P. E. Hopkins

Introduction and History IN speaking of the economic geology of southeastern Ontario, W. G. Miller and C. W. Knight' say that "there occurs in southeastern Ontario a variety of minerals and rocks of economic value, probably as great as in any district of like size on the North American continent. Some of these deposits, including marble and trap, are inexhaustible. Others, including talc and iron pyrites, have proved to be of considerable economic importance. From time to time, during the last 50 years, the following minerals and rocks have been mined or quarried with varying success: gold, iron pyrites, zinc blende, copper pyrites, galena, mispickel, magnetite, hematite, talc, actinolite, mica, marble, ophicalcite, feldspar; fluorite, apatite, corundum, graphite and sodalite. All of the economic materials, with the exception of fluorite, appear to be of pre-Cambrian age. The fluorite veins penetrate the Ordovician, Black River, limestone." Accompanying that report was an article by the writer on the Queensboro Pyrite Area which includes one of the two working pyrite properties in southeastern Ontario. In the present paper will be given a brief description' of all the known pyrite deposits in the area which may at some time possess an economic value, with fuller descriptions of the two working mines-The Canadian Sulphur Ore Co.'s mine near Queensboro, and the Nichols Chemical Co.'s property at Sulphide. The earliest mining of iron pyrites in Ontario was done in 1868 on the Billings property near Brockville. The mines were closed down in 1879 under the assumption that they were exhausted. Many other

Jan 8, 1916

The age of specialization has made man increasingly dependent on a larger number of different metals and minerals. Overexploitation during World War II and lavish squandering of irreplaceable mineral wealth in the past has resulted in the rapidly approaching exhaustion of some of the major domestic ore sources. History clearly points out that the United States cannot continue to be a world power on an "import to survive" policy. A constructive program of development and appraisal of the nation's mineral wealth, including the planned conservation of her resources, must be adopted. Strictly speaking, conservation of minerals must mean the orderly exploitation of our resources and the prevention of waste in use, with due regard for the future. Real concern for the future may not extend beyond a few generations. Eventually science and invention should take care of the problems arising from shortages of some minerals, and the national defense aspects of domestic deficiencies can be provided for by stock piling and other measures. Early conservationists had this viewpoint; but with a rapidly developing industry and population, a farsighted policy that would deny full realization of immediate ambitions became unpopular. Consequently, the politically minded conservationist broadened the concept to include "prudent use of resources" and brought under the conservation umbrella

Jan 1, 1950

By Harry L. Brown, James M. Dickinson, Philip E. Armstrong

The elastic stiffness coefficients of niobium have been rneaslrred from -150°C to over 650 C and ave in accord with the anomalous temperature dependence previously observed for Young's modulus. This unusual behavior has been shown to be the result of changes in the relative values of the shear elastic coefficients. The bulk modulus remained essentially constant over the temperature range studied, while changes in the shear coefficients produced a more nearly isotropic behavior as the temperature increased. A number of investigators have reported data on the temperature dependence of Young's modulus of polycrystalline niobium. The values cited for the room-temperature modulus ranged from 0.71 to 1.17 x 10" dynes-cm-' (10.3 to 17.0 x lo6 psi) and in each case the modulus was observed to decrease with increasing temperature. In our recent study,8 both polycrystalline and single-crystal samples of essentially strain-free high-purity niobium showed a Young's modulus whose temperature dependence as well as magnitude was strongly dependent on specimen orientation. This was shown to be the result of changes in the relative magnitude of the two shear moduli, C and C'. Young's modulus of polycrystalline samples with strong [110] textures and Young's modulus of single crystals whose orientations were away from the [loo] actually increased as much as 12 pct between room temperature and 1000°C. While studies on the residual effects of previous fabrication, thermal treatments, and impurity contents will probably resolve the problem of the widely differing Young's modulus values observed in polycrystalline niobium, a more complete description of the elastic properties requires an evaluation of the single-crystal elastic constants. A knowledge of these constants can provide a clearer picture of the nature of the temperature dependence, as well as establish a basis for predicting the modulus behavior of polycrystalline niobium, both in the randomly oriented condition and with various fabrication textures. The effects of residual strains on the elastic behavior then can be separated from orientation effects. EXPERIMENTAL METHOD Thin rod-resonance techniques were used to obtain both the Young's modulus and shear modulus of single-crystal specimens. The determination of these moduli as functions of the crystallographic orientation of the specimen axis provided sufficient information to permit calculation of the single-crystal elastic constants. The necessity for torsional as well as longitudinal measurements led to the design and assembly of a vertical-tube vacuum furnace incorporating probes for the simultaneous determination of both longitudinal

Jan 1, 1967

By A. N. Chirico

This paper reviews the three major distillation processes: multiple effect (LTV) evaporation, multi-stage flash distillation and vapor-compression forced circulation evaporation. Scale preventative measures are discussed for all saline water applications. Operational data is presented on the Freeport, Texas, demonstration plant, which is the first government facility to produce one million gallons per day of fresh water for a municipality. There has been much publicity concerning the water crisis that confronts many peoples today. There is little doubt that the arid regions - which include the Middle East, parts of Africa and the Caribbean — have suffered to no slight extent for the lack of this most precious commodity. But what about our own country? Government experts have extrapolated demands and flatly predict that by 1980 we will be faced with a shortage of 80 billion gal per day. The validity of this prediction has been disputed by others; however, it appears certain that there will always be a natural abundance in some areas, a shortage of supply in other areas. Distributing our total natural water resource equitably would be impossible. Transmission of water by means of aqueducts can be an expensive undertaking. The controversial Feather River Project in Calif. is an example. The estimated cost for this venture is a staggering three billion dollars. As our population continues to increase and our standard of living rises, agricultural and industrial requirements will be proportionate. What can be done to avoid a crisis? We can conserve and use our water for industrial and irrigation purposes more judiciously: we can attempt to eliminate pollution of our natural resources from sewage and industrial wastes; we can develop, while there is time, saline water conversion processes for the massive production of low cost fresh water. The scope of this paper will be limited to only the distillation type processes that are commercially feasible. The first step in making potable water is to find a source of raw material. An inexhaustible supply is provided by oceans in coastal regions, but the supply of water is more critical in the inland communities of our country. The source of raw material in these. regions is brackish well water and this must be utilized. There is a significant process difference when handling brackish water compared to seawater and this brings out an important fact: No single conversion method can be universally applied to solve all the water problems. Composition of the raw water and degree of distillate purity are factors which must be considered before a particular process is selected. Local conditions at the plant site, fuel costs, labor costs, disposal facilities, etc. are other equally important factors which must be evaluated. WATER CONVERSION PROCESSES Conversion processes commercially feasible today are: 1) multiple effect evaporation, 2) multiple flash distillation, 3) vapor compression distillation and 4) electrodialysis. The first three are distillation processes which take potable water out of the raw water, while the fourth is a membrane process which takes out the salt. In addition to the above there are a good number of other promising methods for production of potable water, many of them in the basic research stage. Freezing is another promising process with commercial potential. This process hinges upon the formation of ice crystals which are free of salt occulsions. Separation and washing of the crystals are problems that must be solved before this process can be considered commercially feasible. Freezing processes have several advantages mostly attributable to the low temperature of operation. This low temperature reduces the scaling and corrosion problems encountered in higher temperature operations. Several different freezing processes are being considered and will be tested in the pilot plant at Wrightsville Beach. One process is a flash freeze process, a second uses a secondary refrigerant such as butane for freezing, and a third process employs a secondary refrigerant particularly controlled to produce large ice crystals. Of the above processes, only the distillation processes are reliable when water of high purity is re-

Jan 1, 1963

By J. K. Kerver, J. S. Osoba, J. G. Richardson, J. A. Hafford

A detailed study of a number of methods of relative permea-abilitv measurement has been made in a search for the tech-niqrle most suited to routine analysis of cores taken from reservoir rock. It has been found from tests run on the same samples of core material by a number of techniques that the Penn State, Hassler, Hafford, and dispersed feed techniques all yield results which are felt to be reliable. Conditions under which the faster single core dynamic technique may be used are described. Further work on the calculation of relative permeabilities to oil from data obtained by the gas drive method is needed before this latter rapid method can be utilized. Correlations between theoretical studies and experimental results have been obtained in studies of the boundary effect. pressure distribution in two-phase flow, and gas expansion effects. Previous conclusions that the effects of the outflow boundary could be made negligibly small have been substantiated. Results of experimentally determined oil and gas pressure distributions along a core sample during flow are presented. Further studies of the effects of rate of flow in the measurement of relative permeability-saturation relations have shown that results are independent of the rate of flow as long as the flow rate is below the point where inertial effects commence. An analysis of the effects of a severalfold expansion of gas along the flow path indicates that while saturation gradients are induced in the test sample, the errors caused by this phenomenon in relative permeability measurements are small. INTRODUCTION Many pages of literature have been devoted to pointing out the need for relative permeability-saturation relations in reservoir engineering. One of the most attractive ways of obtaining this information is by the analysis of samples of core material taken from the formation in question, and again literature has described man); methods for obtaining these data. It is the purpose of this paper to present the work that has been done in the study of some of these published methods together with some other methods that have been recently developed in this laboratory. Also, a study of some of the factors that influence the laburatory determination of relative permeability-saturation relations is presented. FACTORS WHICH AFFECT LABORATORY STUDY OF FLUID FLOW THROUGH RESERVOIR ROCK To determine relative permeability-saturation relations of samples of reservoir rock in the laboratory, it is important to know what factors affect these measurements in order that the magnitude of these effects can be ascertained and steps then can be taken to eliminate or, in some cases, to minimize them. The factors that have been investigated are the boundary effect, the effect of gas expansion. and the rate effect. Boundary Effect In laboratory experiments in which two immiscible fluids are flowed through a porous medium, there exists a discontinuity of capillary properties at the outflow face. This discontinuity exists became the fluids pass from a region of finite capillary pressure in the sample to a region of zero capillary pressure in an open receiving vessel. The capillary forces existing in the core caupe the rock to tend to retain

Jan 1, 1952

By J. S. Kasper, R. M. Waterstrat, B. F. Decker

THE large difference in the X-ray scattering factors for molybdenum and manganese makes the o- phase in the Mn-Mo system an interesting one to study with respect to ordering of the atoms. Such a study has been carried out using data obtained from a powder sample, and the resulting evidence for ordering in this compound is presented here. It is not possible, of course, to obtain all the details of structure for a u phase from powder data only. Most difficult of all would be the determination of precise atomic parameters. There is reason to believe, however, that the atomic parameters do not vary greatly in the different s'S and that the precise values obtained from one s structure would then allow decisions as to the ordering of atoms to be made when there is a large difference in scattering factors. In particular, the powder intensities for Mn-Mo s are for the most part in good agreement with those observed for Co-Cr, for which single crystal studies have been made by the authors.' There are a few marked discrepancies in the intensity comparison of the two s's, and these cannot be removed by adjustment of the parameters. They are interpreted as resulting from a more pronounced effect of ordering of the atoms. Accordingly, the parameters of Co-Cr s' have been used for the calculations of the Mn-Mo intensities. For Co-Cr, the space group is D4h14-P4/mnm with atoms in the following positions: 1—2 in (b); 11—4 in (f), with x=0.1031; 111—8 in (i), with x= 0.3713 and y=0.0370; IV—8 in (i), with x=0.5662 and y=0.2396; and V—8 in (j), with x=0.3160Y and y — -0.250. The unit cell is tetragonal, with an==9.10A and cn=4.74A for the Mn-Mo u phase studied here.

Jan 1, 1955

By R. I. Garrod, R. A. Coyle

The shapes and positions of X-ray reflections from specimens of copper, steel, and aluminum alloy haue been examined in the elastic and plastic ranges both while the specimen was under stress and in the unloaded condition. For the aluminum alloy the shape was unaltered by the application of stress either within the elastic limit or in the plastic range provided that no additional plastic strain was induced. In copper the broadening accompanying plastic deformation was very slightly reduced when the specimen was unloaded. A similay but more marked elastic component of broadening was also found for steel, but in this case below the yield stress. Line profiles corrected for instrumental and particle-size broadening indicate very large internal stresses in local regions of the plastically deformed metals. The results are discussed in terms of a recent suggestion that the heterogeneous dislocation distribution between the cells and their boundary walls plays a major role in the peak shifts and broadening of the X-ray reflections. STUDIES of the X-ray line profiles from strained polycrystalline aggregates concentrate usually on one or the other of two main parameters: a) the displacement of the peak of the intensity contour from its position for a strain-free aggregate, or b) the shape of the profile. From peak shifts data can be obtained either on the relation in both the elastic and plastic ranges between applied external stress and average lattice strains in a given (hkl) direction, or, alternatively, on the residual lattice strains which are present after a plastically deformed specimen is unloaded.' On the other hand, the shapes of the broadened profiles from cold-worked metals can be analyzed to separate the broadening produced by small particle size and by heterogeneous lattice strains.' In this paper the terms "size broadening" and "strain broadening'' are used in the general sense adopted by warren.' In the past, apart from two early qualitative observation, it has been customary to examine only the movements of the peaks of the profiles while the specimen is actually under load, since the line broadening induced by plastic strain remains after removal of the external stress. Consideration of the implications of existing data of this type suggests, however, that fruitful additional information on a number of fundamental aspects might be gained by careful examination of whether the X-ray line profile is in fact different in the loaded and unloaded states of the specimen. By taking advantage of the sensitivity and convenience of modern diffractometer techniques it is possible to explore with relative ease the magnitude and importance of any elastic effects which may be superimposed upon the well-known permanent changes in profile. The main aim of the work to be described was thus to investigate this point for typical metals and alloys. For this purpose annealed specimens were extended first elastically and then plastically and the positions and shapes of X-ray reflections were recorded. Initially it was anticipated that prime interest would center on observations within the plastic range; it has been found, however, that small changes in profile sometimes occur both before and after the nominal elastic limit of the material is reached. It is shown that the results obtained have important implications in relation to the structural changes and processes associated with deformation. I) EXPERIMENTAL To enable the diffraction lines to be recorded while the specimen was under uniaxial-tensile stress, a small hydraulic testing machine was designed and constructed for direct attachment to the goniometer of a Philips diffractometer. The specimens, which were machined from 1/2-in.-diam rod and had a central rectangular section 3/8 by 1/16 in. over a gage length of 1 in., were held in the machine by split collets mounted in grooves in the cylindrical ends of each specimen. No special precautions were taken to ensure precise axiality of loading. Constant oil pressure was maintained by a lever and weights system and transmitted to the loading rig by flexible pipe. The actual load on the specimen was measured by a load cell in the machine to an accuracy of * 1 pct. To enable smooth X-ray profiles to be obtained the specimen and machine were oscillated continuously during recording through *7-1/2 deg about the normal half-angle position of the goniometer. The three materials chosen for the investigations were high-purity copper as representative of a ductile fcc metal, a low-carbon steel for a bcc metal, and an aluminum alloy as a material in which the proof stress/ultimate strength ratio is high. Details are as follows. a) Copper. 99.999 pct purity. After machining the specimen surface was polished mechanically and

Jan 1, 1964

By F. D. Rosi, C. A. Dube, B. H. Alexander

WHEN a deformed polpcrystalline metal is heated to a sufficiently high temperature, a recrystallized structure develops which consists of small, essentially stress-free grains. This transformation is referred to as primary recrystallization. Under certain conditions, on prolonged annealing of the specimens, a type of grain coarsening occurs in which a small number of grains commence to grow at various points by devouring the neighboring finegrained primary structure, which, in itself, exhibits a marked stability toward normal grain growth. This grain coarsening process has been referred to by Burgers' as "secondary recrystallization" or "exaggerated grain growth." Although much work has been done on recrystallization and growth processes, present knowledge of the factors which determine the occurrence and growth of secondary grains is inadequate for the advancement of a theory which accounts for the observed characteristics of this recrystallization phenomenon. In this respect, it would be important to make measurements of the velocity of growth of these large secondary grains. The early work of Feitnecht2 on aluminum showed that the size of secondary grains increased with temperature and time, suggesting that such measurements would be possible. More recently, Burgers1 found that the growth velocity of these grains in aluminum was constant over a large time interval, as is generally found for the growth velocity of primary grains in a uniformly deformed test piece.3-5 It is reasonable to expect that the determination of the activation energy of the secondary growth process might lead to a better understanding of the underlying atomic mechanism. This investigation, therefore, is one of a series primarily designed to measure the growth velocity of secondary grains at various temperatures for silver, copper, and aluminum. It is hoped that these studies along with those of orientation relationships, will establish a sound basis for theorizing as to the origin and nature of the secondary transformation. Experimental Procedure The metal used in the present investigation was high-purity silver (999.9 fine), which was supplied in the form of cold-rolled plates 0.250 in. thick. These plates were annealed at 500°C for 1 hr and then straight-rolled to a thickness of 0.04 in. in three reductions of approximately 45 pct, followed in each case by an anneal at 450°C for 1/2 hr. The 0.04 in. sheets were given a final reduction of approximately 50 pct, which resulted in a thickness of 0.02 in., thereby insuring two-dimensional crystal growth. Individual specimens of this material about 1x3 cm were used for all heat treatments, unless otherwise noted. The annealing was carried out under an atmosphere of argon in an Inconel tube furnace whose temperature was controlled to within -+2°C. Metallographic examination of the secondary transformation was accomplished by mechanically polishing the specimens on one side to approximately one half their thickness through 2/0 metallographic emery paper, and then electrolytically polishing in a solution of potassium ferrocyanide and sodium cyanide. With a current density of approximately 20 amp per sq dm, the time required to obtain a satisfactory surface varied from 3 to 5 min. Standard potassium bichromate was used to etch the electrolytically polished surfaces. A heavy etch with this solution produced a sharp contrast between the secondary grains and the fine-grained primary structure, darkening the latter while leaving the large secondary grains bright. All area measurements of the secondary crystals were made with a planimeter on enlarged tracings of the grains.

Jan 1, 1953