Search Documents

By J. Handin, S. J. Bauer, M. Friedman

Deformation mechanisms in room-dry and water-saturated specimens of Charcoal Granodiorite, shortened at 10-4s-1, at effective pressures (Pe) to 100 MPa and temperatures to partial melting (?1050°C) are documented with a view toward providing criteria to recognize and characterize the deformation for geological and engineering applications. Above 800°C strength decreases dramatically at effective pressures ? 50 MPa and water-weakening reduces strength an additional 30 to 40% at Pe = 100 MPa. Strains at failure are only 0.1 to 2.2 percent with macroscopic ductility (within this range) increasing as the effective pressures are increased and in wet versus dry tests. Shattering (multiple faulting) gives way to faulting along a single zone to failure without macroscopic faulting as ductility increases. Microscopically, cataclasis (extension microfracturing and thermal cracking with rigid-body motions) predominates at all conditions. Dislocation gliding contributes little to the strain. Precursive extension microfractures coalesce to produce the throughgoing faults with gouge zones exhibiting possible Riedel shears. Incipient melting, particularly in wet tests, produces a distinctive texture along feldspar grain boundaries that suggests a grain-boundary-softening effect contributes to the weakening. In addition, it is demonstrated that the presence of water does not lead to more microfractures, but to a reduction in the stresses required to initiate and propagate them.

Jan 1, 1982

By Albert Sauveur

(Winces-Barre Meeting, June, 1911.) THE instrument about to be described meets so perfectly the special needs of the metal microscopist that there seems to be little doubt but its merits must be readily appreciated by those who have had any experience in the microscopical examination of metals. The Microscope-Stand.-The microscope-stand proper, Fig. 1, consists of a microscope-tube, provided with both coarse and fine adjustments of the best construction, and with a draw-tube, rigidly mounted on a bar supported at both ends on substantial and firm cast-iron legs. The height between the table and the under side of the supporting bar is 5 in. and the distance between the supporting legs 12 inches. This arrangement' affords free space below the objective for the examination of large specimens of metals, such as full rail-sections, without detracting in the least from the value of the instrument when applied to the examination of the usual small specimen, as explained later. Many metal microscopists frequently have to examine bulky specimens, and this is altogether impossible with the ordinary microscopes as well as with the special metallurgical microscopes which have been designed and described from time to time. Recourse must be had to all sorts of makeshifts for the proper support of large specimens, or, more often, the microscopist gives up the attempt altogether, or else resigns himself to the cutting of the bulky samples into small pieces to -be laboriously polished and separately examined. It is believed that an instrument permitting the examination of large as well as of small specimens with equal ease and accu-

Dec 1, 1911

By Charles Means

A THOROUGHLY modern coal-handling system has been installed at the Pittsburgh Terminal R. R. & Coal Co.'s new No. 8 shaft, or Coverdale mine, about 11 mi. (17.7 km.) from Pittsburgh on a spur f the Montour R. R. The Pittsburgh seam, which is the one worked, is reached at a depth of 342 ft. (104 m.). Power is delivered to the mine at 22,000 volts over a transmission line of the bow-arrow type of construction. A private telephone line connecting the various mines and the main office in Pittsburgh is carried on the same poles. The high-tension line is brought to an outdoor, step-down, transformer substation, where three 833-kv.-a., single-phase, 60-cycle, oil-insulated, self-cooled transformers reduce the potential to 2300 volts. The transformers are protected by electrolytic, aluminum-cell lightning arresters, horn gaps, and choke coils. High and low-tension busses, together with fuses, choke coils and air-break horn-gap switches with their remote-control operating mechanism are mounted on a substantial structural-steel tower 25 ft. (7.6 m.) in height. MINE SUBSTATION The transformer substation is adjacent to a pressed-brick building that houses direct-current substation equipment together with switchboards, etc., for the control and distribution of power. This building also contains the hoist for the men and supplies.

Jan 9, 1921

By Joseph Gurland

EVERAL carbide-cobalt compositions were pre-^-5 pared for the purpose of determining the transverse rupture strength of various carbide-binder systems. The binder content was held at 10 and 37 volume pct Co, so as to be representative of low and high bjnder compositions. The carbides used, WC, Tic, TaC, CbC, VC and ZrC, were selected on the basis of availability, knowledge of their properties, and small solid solubilities in the binder metal at room temperature. The methods of preparation and carbon analysis of the carbides are summarized in Table I. The carbides with cobalt added were ball milled, pressed, and sintered. vacuum sintering was used throughout, except for the WC-Cs alloys, which were sintered in hydrogen. The sintering temperatures ranged from 2500" to 2750°F for the low binder alloys and from 2300" to 2550°F for the high binder alloys. Compositions and properties of the sintered com- pacts are presented in Table 11. For the transverse rupture strength, the average and range of the five best samples of each alloy are listed. Discrepancies between the actual and theoretical densities are attributed to carbon deficiencies in some samples. The theoretical densities were calculated by assuming mixtures of carbides of stoichiometric compositions and cobalt. Representative microstructures are shown in Figs. 1 to 6. The porosity was A-2 or better' in all alloys except those with ZrC. A grain size of about 3 p was

Jan 1, 1958

By Robert J. Willard

The scanning electron microscope (SEM), became commercially available in 1966. Embodying some unique features not provided by conventional electron microscopes, this new electron-optical instrument offers the scientific community a new way of observing the surfaces of materials. In rock mechanics research, the SEM should prove a useful basic tool in characterizing rock fracture on a very small scale and thus contribute to a better understanding of rock behavior at larger scales. This article presents one example of how the SEM is being applied to such research at the Twin Cities Mining Research Center operated by the U.S. Bureau of Mines in Minneapolis. This research center conducts theoretical and experimental studies on a broad range of mechanisms that induce disintegration by the application of energy to rock.1 Some of these studies are concerned with the relation of microstructure to rock behavior and are carried out mainly with the petrographic microscope. At the same time, however, the center recognizes that this relation must be studied through several orders of magnitude, from lattice-size units of rock-forming minerals to field-size rock units. The SEM fits this scheme by extending the capability of the petrographic microscope into smaller orders of magnitude. However, because its resolution is limited to about 200 A at 10,000x, the SEM is not capable of resolving lattice-size units, and hence a conventional electron microscope with a much greater resolution capability is necessary at this order of magnitude.

Jan 6, 1969

By C. B. Scotty, E. F. Egan

INTRODUCTION The neutron-garnma log has been used for stratigraphic correlation by the oil industry for a number of years. In the past few years, the quantitative application of the log to provide information with respect to porosity has received considerable attention. The basic concept of quantitative interpretation has been pointed out in the literature.1 It shall be the purpose of this paper to develop by empirical means a method whereby the relationship of porosity to neu. tron-gamma deflection may be predicted for various bore hole diameters. This relationship is applicable to the present commercially available neutron-gamma log run in open hole. Data available at present are insufficient to establish similar correlations for cased holes. Through the development of such a correlation, the importance of the various factors which influence the log become evident. NEUTRON-GAMMA CURVE The logging tool conisists of a source of neutrons and a means of detecting and measuring gamma rays, the detector being shielded from the direct emission from the source. The gamma rays reaching the detector have three sources of origin: (1) the natural gamma radiation emitted by the formations, (211 induced gamma radiation resulting from neutron bombardment. (3) gamma rays emitted by the source and scattered by the formation. It has been found that a neutron derived porosity correlation is best for shale-free formations. Under this condition the natural gamma ray radiation is quite low, and therefore, will be neglected in this work. The induced gamma ray radiation resulting from neutron bombardment is predominantly a function of the hydrogen atom concentration of the substance penetrated. Due to the geometry of the presently used system, the neutron-gamma curve indicates low radioactivity opposite high hydrogen concentration and high radioactivity opposite low hydrogen concentration (Figs. 1 and 2). Having a curve which measures hydrogen atom concentration, it follows that if the matrix of the formation penetrated consists only of atoms other than hydrogen, and if the fluid filling the pores is either oil or water, the curve should be an indication of porosity (both oil and water have practically the same number of hydrogen atoms per unit volume'). The above criteria for a porosity (Correlation are fulfilled in clean sandztones and limestones in which the pore volume is completely filled with liquids (oil or water), but not in formations containing either free gas or shale or both. Free gas. even under pressure, contains considerably less hydrogen per unit volume than oil and water; therefore, a variation in response on the curve would be expected. Camp- bell and Winter,' indicate that this difference in hydrogen concentration is sufficient to distinguish between sands containing water or oil and those containing dry gas. Shale is a mineral that contains hydrogen in its molecular structure in addition to the hydrogen which is present in the water of hydration. Thus, in formations containing variable amounts of shale, the hydrogen concentration indicated by the curve is not a direct indication of porosity. Bush and Mardock' have indicated that a correction may be made by use of the gamma ray curve to provide a porosity correlation. Since the induced gamma rays are predominaiitly a function of hydrogen concentration, it would be anticipated that the fluid filled bore hole would materially influence the logs. It has been pointed out that the neutron-gamma curve response decreases with increase in hydrogen concentration, therefore, the response due to the induced gamma ray component decreases with increase in fluid filled hore hole diameter. The scattered gamma ray component of the log increases with increase in bore hole diameter. Although there is an

Jan 1, 1952

By AIME AIME

COAL occupied a large place in the technical sessions of the Institute at its annual meeting for in addition to three sessions specifically de- voted to coal the two sessions on mine ventilation and the two on ground movement and subsidence, which are reported under their own headings, were primarily concerned with coal. The first session on coal was a joint one with the Iron and Steel Division, on Wednesday afternoon, with F. H. Crockard and J. R. Campbell presiding as joint chairmen and the latter actually officiating. The principal topic of discussion was G. S. Scott's paper "Evaluation of Coal for the Making of Blast- Furnace Coke," which has been published as T. P. 159. The author made a brief statement of its con- tents to start the discussion and the chairman, after briefly reviewing it himself, called on C. A. Meissner to start the discussion. He briefly reviewed the economic factors in the use of coal for coke-making, saying that not only .does the removal of 1 per cent of ash from the coal reduce the cost of pig iron 12 or 13c. per ton, but it also permits coke of satisfactory structures to be made from a coal which otherwise could not be used. He stressed the importance of uniformity in blast-furnace fuel and discussed the benefit of mixing different coals as raw material for the coke oven and cited experience with Illinois coals.

Jan 1, 1929

By E. T. Dumble

(Cleveland Meeting, October, 1912.) FOR many years there have been occasional reports of the discovery of gold from a belt of the coast country of Texas which is underlain by deposits belonging to the lower Eocene. For the most part they have been treated as newspaper reports and no examination or record of them has been made. Among such, it may be mentioned that in 1896 there was a flurry over reported gold-discoveries -west of Luling and elsewhere in this belt, and in 1903 some prospect-shafts were sunk on the Gonzales branch of the Galveston, Houston & San Antonio railway, 3 miles below Harwood. During 1912, further discoveries have again brought the matter to our attention, and it may be of interest to record the facts as we have found them. Some years ago specimens were sent me, which were said to have been taken from certain beds on Gazley creek, and concentrated by washing in it rocker. In them were several particles of gold sufficiently large to be visible to the eye. Under the microscope they showed to be, with few, exceptions, sharp cornered, and not rounded as is usual with placer-gold. They were not filings, however, but their sharpness seemed rather to be due to a recent freeing from their matrix. One or two grains were rusty, and one copper-hued, but the most of them were tolerably bright. On examining the material of the samples small grains or fragments were found, of a yellowish brown color, which seemed to be of a finely-granular structure-possibly a sandstone. In these fragments I found particles of gold, one of them being large enough to be visible without a lens. Gazley creek empties into the Colorado river just north of Smithville, and for a few miles north of that place its banks show, beneath the deposits of more recent materials, the sands and clays of the Lignitic division of the Eocene, with lignite, shells of iron, etc.

Oct 1, 1912

By OTTO HERRES

UTAH has enormous deposits of high-grade bituminous coal. The United States Geological Survey estimates that there are 13,130 sq. mi. of land in Utah known to contain workable coal and these extensive fields contain 196,000,000,000 tons of coal. Growth in population and development of industry in the intermountain and Pacific coast regions will in time give Utah a place with the great coal producing states of the country. Even today, faced by adverse conditions in competition with cheap fuel oil from southern California, water-power throughout the western states in general, and comparatively high freight rates to its distant markets, the Utah coal industry is notable in many respects. In recent years, Utah has led the United States both in the percentage of its mines in class 1, mines producing more than 200,000 tons a year, and in average production per man per day, which was 6.01 tons in 1921. In Mineral Resources of the United States, 1921, Part

Jan 1, 1925

By AIME AIME

THANKS to the excellent preliminary work of: the Division officers and the local committee the fall meeting of the Coal Division at Bluefields was a brilliant success. West Virginia was at its best with its beautiful mountains, good roads and foliage, just beginning to turn to autumn colors. The meeting began on time and was kept on time throughout. The papers were-well prepared and, being on subjects of live interest, provoked 'lively discussion. One factor in bringing this about was that they were not too numerous and that with one exception copies had been submitted in advance a sufficient time to permit of them having been studied. The Friday morning session was presided over by John .J. Lincoln of the Crozier Coal and Coke Co. and president of the Pocahontas Coal Operators Association. After brief announcements by Thomas H. Clagett, chairman of the local committee, regarding plans for the two day's involved, and by Howard N. Eavenson, chairman of the Division, the reading of papers was taken up.

Jan 1, 1931

L. S. PANYITY.-I made inquiries from the Smith and Dunn people, who are the originators of the compressed air and gas method of increasing the production of oil wells, as to how much pressure the sand will stand; that is, relative to the original rock pressure. They tell me that they have not been able to show, up to date, any pressure in a sand greater than the original pressure. I have also made 'a statement to that effect, but I am really dubious as to whether that is right, as I am not sure that you cannot get a greater pressure. However, I think that a greater pressure would be dangerous because it might cause a loss of gas. C. H. SHAW, ? Lawton, Okla.-In regard to the gas that was put into the pool up in New York State, may it not be possible that, on account of errors, etc., in measuring or computing, there is a mistake in the apparent fact that more gas was gotten out than was put in? L. S. PANYITY.-Unfortunately, I have not the papers I expected from those people to show the actual conditions, but I do not doubt that such

Jan 4, 1919

By J. J. Foster

MOST of us will, I think, agree that never before in the history of the coal industry has the human side of our business been so important as today. Since, even in wholly mechanized mining, labor cost is such a large percentage of out total cost we are all deeply concerned not only about the present attitude of our employees but particularly about the future, when the industry returns to a "survival of the fittest" basis. Many things could and should be done about our employee relations in the coal business. Failure to recognize these obligations and do something about them may lead to serious consequences, the least serious of which will be the loss not only of many of our better employees but a large portion of our potential employees, as they graduate from our schools to other in¬dustries. Some of these things should be handled by the industry as a whole whereas others should be done by individual companies. Due to varying conditions and size of organizations it would, at best, be necessary to vary a program to meet the individual needs of each operator.

Jan 1, 1945

By Cyril Smith

IN the study of the structure or the properties of a series of alloys or nonmetallic compounds, it is often advantageous to express the com-position not as percentage by weight, according to which the material is always made up and analyzed, but as the atomic percentage of the two constituents. The conversion from the one to the other is repre-sented by the formulas: 100A 100x or 1 x/A+100-x/B B(100-x) _ 100yA 100y [2] X. yA + (100 - y)B or y (100 - y) where x and y are the weight and atomic percentages respectively of the element of atomic weight A, and (100 - x) and (100 - y) are the per-centages by weight and by atoms respectively of the element of atomic weight B. While calculations according to these formulas are simple, they are time consuming if several conversions have to be made. In 1931 Water-man1 constructed a nomograph for performing the conversion, but this did not permit an accuracy greater than about 1 per cent to be obtained in the neighborhood of 50 per cent. Ölander2 has proposed a graphic method simpler than Waterman's and one that gives a uniform precision throughout the entire scale. The possible accuracy is about 0.5 per cent of the whole, depending on the size and accuracy of the coordinate paper used. Recently, Hermann3 has described a slide rule for making the calculations. These devices make use of the simple rearranged equation

Jan 1, 1933

By Cyril Smith

IN the study of the structure or the properties of a series of alloys or nonmetallic compounds, it is often advantageous to express the com-position not as percentage by weight, according to which the material is always made up and analyzed, but as the atomic percentage of the two constituents. The conversion from the one to the other is repre-sented by the formulas: 100A 100x Y x 100 ? x/A A [1] A+ B x + A/B(100-x) X _ 100yA 100y [2] yA+(100-y)B or y+A(100-y) where x and y are the weight and atomic percentages respectively of the element of atomic weight A, and (100 - x) and (100 - y) are the per-centages by weight and by atoms respectively of the element of atomic weight B. While calculations according to these formulas are simple, they are' time consuming if several conversions have to be made. In 1931 Water-man' constructed a nomograph for performing the conversion, but this did not permit an accuracy greater than about 1 per cent to be obtained in the neighborhood of 50 per cent. Olander2 has proposed a graphic method simpler than Waterman's and one that gives a uniform precision throughout the entire scale. The possible accuracy is about 0.5 per cent of the whole, depending on the size and accuracy of the coordinate paper used. Recently, Hermann3 has described a slide rule for making the calculations. These devices make use of the simple rearranged equation:

Jan 1, 1933

By F. C. Miller

THE metallurgical fuel of Colorado, Utah, and New Mexico has been a very tardy member in the caravan of western industrial progress. The history of western coke has naturally been closely related to the development of the metallurgy of iron and steel and the precious metals, in the State of Colorado. It was at Leadville, with a population of 300 in 1877, that the Sentinel was published by Richard S. Allen. The Sentinel gave very full accounts of the various mineral discoveries at the new town of Leadville, which found their, way to the more widely circulated journals of the East, and attracted the attention of many people. At the close of 1878, a census showed a total of 5040 persons. The first smelter was established in 1877, at Malta, two miles from Leadville, by A. R. Meyer, but was not successful. It was succeeded by the Harrison Reduction Works, in 1878. The La Plata began with one furnace in June, 1878, and in 1879 had four furnaces in active operation. These furnaces used charcoal for fuel, and, because of hot tops, suffered a tremendous loss in lead and silver. This difficulty was overcome by the erection of 50 single-bank 10-ft. beehive ovens at Crested Butte, Colo., in 1880. The slack coal sent to these ovens was very pure, and yielded a coke carrying as little as 4.5 per cent. ash. Among the pioneers in the Leadville district were Grant, Eddy, James, Billings, Eiler, and Dickson. To these men the West owes the present expansion of its mining industry, and the erection of metallurgical processes for the treatment of precious metals.

Jan 8, 1918

By D. W. Brunton

THE maps of our large mines are usually prepared with the greatest care; and it is somewhat singular that, in comparison with the great amount of time and money spent in surveying and platting, so little actual use is made of them. Almost the only purpose for which a completed survey-map is afterwards consulted, is the determination of the relative position of the different workings to each other, and to the boundary-lines of the property. After the completion of such a map, it should be made the beginning of another, and in most cases a far more important, undertaking, namely, its utilization as -a starting-point for a complete inventory of the company's underground possessions. The ordinary mine-survey map, being nothing but a record of what has been done, is, in one sense, only ancient history. To increase its value, such additions should be made as will render it a complete statement of the amount and value of ore in sight at any particular time, and a guide for future develop¬ments. Comparatively little extra labor is involved in this undertaking, since the larger and most expensive part of the work has already been completed when the mine has been surveyed and mapped. The necessary additions consist in working out, and platting on the maps, the geology of the mine as exposed in the workings, in such a manner that the geological survey may be of daily use in the development and operation of the mine. The first step towards the production of a geological map consists in tracing individual level-sheets from the general or composite map. The area to be included, outside of the property in question, will depend very much on local conditions; but, for geological, legal and commercial reasons, it should be extended as far as reasonably practicable. The scale to be

Sep 1, 1905

By CHAS. A. R. LAMELY

In the extreme northeast corner of the State of Washington, on the Canadian border, lies the Metaline mining district. This district is old in history, but young in production. The Metaline district is a zinc-lead area of the replacement type in dolomite and limestone. The ore bodies of the Josephine horizon are in many ways similar to the ore bodies of the famous Tri-State zinc fields. The beds are faulted and folded and have varyng low dips in varying directions, and underlie large areas of the district. Production started in 1927 on a very limited basis. The property is now mining and milling 700 tons per day. The mine is opened by adit tunnels and a vertical shaft. As the ore horizons gained depth, it was necessary to sink inclines to follow the ore horizon (see Fig 1). From 1927 to date, approximately 600,000 ft of diamond drill was put down This work indicated that sufficient tonnage existed to justify a redesigning of the whole operation, surface and under- ground. After four years of general study, the following program was planned :

Jan 1, 1949

By George H. Deike

UNDERGRADUATE interest in coal mining engineering has dropped to an alarmingly low level. Most companies having co-operative scholarship programs have been forced to abandon them for the duration.

Jan 1, 1944

By Carl A. Zapffe, George A. Moore

IN a previous publication from this laboratory1 the conclusion was drawn that the embrittling effect of occluded hydrogen on iron and steel must result from the precipitation of the gas within small openings through the crystal structure. A review of the literature then published indicated the real existence of crystal sub- structures of the mosaic type and gave presumptive evidence that the "rift openings" associated with hydrogen occlusion are the same as the "disjunctions" of the mosaic theory. Inasmuch as no clear conception of the actual nature of the crystal fragments and openings inherent in these theories has been established, it was considered desirable to obtain direct micrographic evidence of their true configuration. In this direction the standard methods of metallographic attack have proved useless. Recourse was had, therefore, to the direct examination of the surfaces upon which failure by cleavage had resulted from the presence of hydrogen. It was expected that such a surface, un- affected by chemical attack and undistorted by polishing, would reveal the fine openings penetrated by the gas and thus indicate the real nature of the substructures. MATERIALS STUDIED In commercial steels, defects caused by hydrogen take various external forms ac- cording to such factors as structure and purity, and to the extent to which hydrogen either occludes or produces chemical changes. The present work relates only to the well-known transcrystalline hydrogen embrittlement-"pickling brittleness"-in which elemental hydrogen occluded within the grain develops cleavage characteristics. For example, hydrogen embrittlement resulting from hydrogen reaction products is excluded from detailed study. It was also desirable, as far as possible, to have the study uncomplicated by other elements which themselves cause brittleness. Three types of iron were used. These included ingot iron, decarburized free- machining steel, and a specially prepared, aluminum-killed, electrolytic iron. This , choice allowed a comprehensive selection of unavoidable minor impurities and inclusions, which could subsequently be shown to have no specific effects on the structures within the grains. Carbon, and any other impurities free to react with hydrogen, were first removed by a preliminary annealing treatment in hydrogen. Subsequent treatment in vacuo extracted much of this hydrogen and its gaseous reaction products. The resultant ductile iron was then embrittled either by a second anneal in hydrogen, followed by rapid cooling, or by cathodic electrolysis. Group I: Prepared from Armco Ingot Iron As shown in Table I, the principal impurity in this iron was oxygen, which survived the purifying treatment to a large extent. Two series were prepared. The first (Nos. SIO-24) was purified only one day in hydrogen and dehydrogenized one day in nitrogen. Containing both hydrogen and its

Jan 1, 1943

By Carl A Zapffe, George A. Moore

In a previous publication from this laboratory1 the conclusion was drawn that the embrittling effect of occluded hydrogen on iron and steel must result from the precipitation of the gas within small openings through the crystal structure. A review of the literature then published indicated the real existence of crystal substructures of the mosaic type and gave presumptive evidence that the "rift openings" associated with hydrogen occlusion are the same as the L'disjunctions" of the mosaic theory. Inasmuch as no clear conception of the actual nature of the crystal fragments and openings inherent in these theories has been established, it was considered desirable to obtain direct micrographic evidence of their true configuration. In this direction the standard methods of metallographic attack have proved useless. Recourse was had, therefore, to the direct examination of the surfaces upon which failure by cleavage had resulted from the presence of hydrogen. It was expected that such a surface, unaffected by chemical attack and undis-torted by polishing, would reveal the fine openings penetrated by the gas and thus indicate the real nature of the substructures. Materials Studied In commercial steels, defects caused by hydrogen take various external forms according to such factors as structure and purity, and to the extent to which hydrogen either occludes or produces chemical changes. The present work relates only to the well-known transcrystalline hydrogen embrittlement—-"pickling brittleness "—in which elemental hydrogen occluded within the grain develops cleavage characteristics. For example, hydrogen embrittlement resulting from hydrogen reaction products is excluded from detailed study. It was also desirable, as far as possible, to have the study uncomplicated by other elements which themselves cause brittleness. Three types of iron were used. These included ingot iron, decarburized free-machining steel, and a specially prepared, aluminum-killed, electrolytic iron. This choice allowed a comprehensive selection of unavoidable minor impurities and inclusions, which could subsequently be shown to have no specific effects on the structures within the grains. Carbon, and any other impurities free to react with hydrogen, were first removed by a preliminary annealing treatment in hydrogen. Subsequent treatment in vacuo extracted much of this hydrogen and its gaseous reaction products. The resultant ductile iron was then embrittled either by a second anneal in hydrogen, followed by rapid cooling, or by cathodic electrolysis. Group 1: Prepared from Armco Ingot Iron As shown in Table 1, the principal impurity in this iron was oxygen, which survived the purifying treatment to a large extent. Two series were prepared. The first (Nos. SIO-24) was purified only one day in hydrogen and dehydrogenized one day in nitrogen. Containing both hydrogen and its

Jan 1, 1943