Search Documents

By A. Lubinski, J. L. Logan, W. S. Althouse

A4ost gas twells and flowing oil wells are completed and treated through a string of tubing and a packer. Changes in temperature and in pressure inside or outside the tubing will: (I) if free motion of the tubing inside the packer is permitted, increase or decrease the length of the rubing; or (2) if free motion is prevented, induce forces in the tubing and on the packer. If pressure inside the tubing is greater than outside, the tubing may buckle helically even in the presence of a packer-to-tubing tension. The tubing will always buckle, and much more severely, if free motion is permitted. The buckling may be prevented by pulling the tubing in sufficient tension. The prediction of these forces and tubing movement has here to fore been based upon calculations that did not inciude helical buckling. This paper preseitts means with which these length or force changes can be calculated while taking into account the effect of helical buckling. To avoid damaging formations, failure of remedial operations, or damage to the tubing or packer, application is made to practical problems involving calculations of the required length of seals, amount of sluckoff or tension, and prevention of permanent corkscrewing. INTRODUCTION Leakage of a packer may result in costly failures of such operations as squeeze cementing, hydraulic fracturing, etc. To avoid such failures, the authors are often asked questions pertaining to the length of necessary seals, the amount of necessary slackoff, etc. Published work' does not take into account helical buckling of tubing. Investigation of helical buckling was prompted by the fact that allowance must be made for this phenomenon in order to provide relevant answers. In the past, theoretical work on helical buckling was confined to conditions for which such buckling does not The mathematical treatment of behavior in a buckled condition, given in the Appendix, is novel. Assumptions upon which this investigation is based are listed and discussed in a special section. The following are a few of the many kinds of problems which may be solved with this paper. 1. Consider a packer in which tubing may move. Such movement will occur after pressures and temperature are changed. The paper provides means for: (a) calculating the amount of such movement and, therefore. the required length of seals; and (b) calculating the necessary amount of initial slackoff, for which there is no danger of unsealing the packer, if the length of seals is given. Such calculations, as well as those which follow, tully take into account the fact that part of the movement ib due to elastic helical buckling of the lower part of the string. This buckling may occur even in tubing under tension. Insufficient initial slackoff for a given length of seals, or insufficient length of seals for a given slackoff, may result in costly failures. A field case of such a failure will be given further in this paper. 2. In the case in which tubing cannot move in the packer, changes of pressure and temperature result in tubing-to-packer forces and forces in the tubing above the packer, both of which may be calculated. This knowledge is important because, if these forces are too large, the) could damage the packer or the tubing. 3. For wells in which wireline tools are to be run through the tubing, the paper provides means to keep the tubing from buckling, thereby permitting free passage of tools. 4. In deep wells, mainly in the presence of large casing, tubing may become "corkscrewed", i.e., take a permanent helical set. A field case is described further in the text. Using this paper, one may calculate in advance conditions under which permanent corkscrewing would occur, and then take preventive steps. HELICAL BUCKLING Consider a string of tubing, freely suspended in the absence of any fluid inside casing, as shown in Fig. I(a). Now consider an upward force F applied at the lower end of this tubing. This force compresses the string; and if the compression is large enough (which is always the case in actual problems), the lower portion of the string will buckle into a helix, as shown in Fig. 1 (b). The lower end of the tubing is subjected to a compression F. This compression decreases with the distance from the bottom and becomes nil (neither compression nor ten-

By W. E. Bearce

The recent concern for the recovery of even the finest fractions of coal preparation plant feeds has created needs for new equipment. Thermal dryers currently available have difficulty reducing the filter cake moisture on down to the desired point. This difficulty involves 1) the physical problem of handling this wet, sticky material and making each particle accessible to the hot gases, and 2) removing the extremely fine dried particles from the cooled gases. The dryer described in this paper handles the first of these problems, and eliminates the second by the substitution of steel balls for air as the heat transfer medium. As a general statement, the cost of preparing coal for market is inversely proportional to the size of the lumps or particles. In the not too distant past the finer sizes were discarded as being uneconomical to treat and this practice might be still continuing if it were not for the insistence of the public that this material be kept out of our streams. This being the only cost-free outlet, the disposal of fine refuse became a significant item of expense in every preparation plant. When this happened it was only reasonable to look to the recovery of the values in this material, not only to defray this expense, but to reduce the tonnage which had to be wasted. There seemed to be no device available suited to reducing the moisture in this material to what the market requires. All of the fine coal dryers commonly employed make use of air to bring the heat of combustion into contact with the coal particles. Any device employing air as a heat transfer medium, has the following two strikes against it in attempting to handle 28 mesh by 0 filter cake: 1) It is practically impossible to bring the hot air into intimate contact with the enormous number of fine particles stuck together in the cake. 2) Even if this can be effected, it is impossible to remove the dried coal from the air. A wet scrubber must be employed, the discharge of which must go back to the filter and dryer as a circulating load of the most objectionable sort, being the extreme fines. Various compromises have been used to cope with the problem of drying this relatively small tonnage of high moisture coal. Often some of the dried coal is mixed back with the feed to the dryer in an attempt to make the mixture more handleable and more available to contact with the hot air than the filter cake alone would be. This may help to some extent with the first problem but it does nothing about the second and a dryer operated in this way has to be oversized. Sometimes the filter cake is mixed with a coarser fraction for the same reason. Here again, while this may make a mixture (the particles of which are more readily brought into contact with the hot air), the problem of getting the fine coal out of the air remains and a larger percentage of the total coal to be dried is handled by the most expensive means. Mechanical dewatering has accounted for more and more of total coal drying lately and in many cases would satisfactorily handle the whole load, down to 28 mesh, if there were a means available for doing a good job on the —28 mesh by itself. The dryer which is the subject of this paper was designed expressly for doing this job — drying fine material by itself regardless of how wet it may be to start with, how fine it may be, or how gummy and sticky these properties in combination may make it. The essential features are depicted in Fig. 1. A rotating cylinder is supported on a frame in such a way that one end may be raised or lowered by hy-

Jan 1, 1968

The Fifth Annual National Exposition of Chemical Industries will be held in Chicago at the Coliseum and First Regiment Armory during the week of Sept. 22. It was decided to hold the exposition in Chicago, this year, for two reasons: The U. S. Army commandeered the Grand Central Palace Exposition Building in New York, immediately on the close of the last exposition and converted it into a receiving hospital, the use for which is now, happily, nearly ceased; and it was thought that the Exposition would succeed in bringing about a greater development of chemical industries in the Chicago district and the adjoining states. The Advisory Committee of the Exposition consists of: Charles H. Herty, Chairman, Editor Journal of Industrial and Engineering Chemistry; Raymond F. Bacon, Director, Mellon Institute; L. H. Baekeland, Member Naval Consulting Board; W. D. Bancroft, President, American Electrochemical Society; Henry B. Faber, Industrial Filtration Corpn.; Ellwood Hendrick, President, The Chemists' Club; Bernard C. Hesse, Chemist, General Chemical Co.; A. D. Little, President, Arthur D. Little Inc.; Wm. H. Nichols, President, American Chemical Society; R. P. Perry, Vice-president, The Barrett Co.; H. C. Parmelee, Editor Chemical &; Metallurgical Engineering, G. W. Thompson, President, American Institute of Chemical Engineers; T. B. Wagner, Vice-president, U. S. Food Products Corpn.; M. C. Whitaker, President, U. S. Industrial Chemical Co.; and Charles F. Roth and Fred W. Payne. There is also added a special Chicago committee consisting of L. V. Redman, W. D. Richardson, A. V. H. Mory, Carl S. Minor, F. W. Willard, and Wm. Hoskins; the managers, as in the past, are Charles F. Roth and Fred W. Payne.

Jan 6, 1919

By R. F. Mehl, M. L. Swanson, J. P. Hirth, G. M. Pound

The sorption of zinc in a-brass was investigated. By analyzing the elliPtically polarized light reflected from the surfaces of a-brass solid-vapor couples, their optical constants and surface compositions were determined. It was shown that the surface compositions approached an equilibrium value exponentially with time. The bulk diffusion coefficient, surface diffusion coefficient and condensation coefficient for a-brass solid-vapor couples were calculated near 350°C from the experimental results. It has been assumed during various diffusion experiments with bimetallic solid-vapor couples (Dunn,1 Seith and Kraus,2 Jenkins,3 Balluffi and Seigle,4 and others) that the surface composition of such couples reaches its equilibrium value immediately. Although this assumption is probably valid at elevated temperatures, it is certainly not expected to be confirmed at lower temperatures.* consequently, it was decided that a fundamental experiment, designed to solve this problem as well as to examine all aspects of bimetallic sorption, would be the investigation of the rate of approach to equilibrium of the surface composition of solid-vapor couples. The sorption (i.e., adsorption, absorption, and desorption) of metals is obviously dependent on the state of the metallic surface and substrate. Much recent theoretical8"9 and experimental10-12 work on condensation and evaporation of pure metals has shown that the surface contour in atomic dimensions is a critical factor in sorption, so that any deformation or contamination13,14 of the surface exerts a profound influence. It is also known that absorption or diffusion occurs much more rapidly along grain were and in other deformed regions. Thus an effective sorption experiment must utilize a strain-free and clean surface, or at least a clearly defined and reproducible surface state. A mechanically polished surface is in a highly deformed17-l9 state. Because the degree of this deformation is uncertain, it is clear that for most experimental purposes a strain-free (i.e., etched, chemically polished, or electropolished) surface is desirable. Although adsorbed gas molecules on metallic surfaces are unavoidable even in the highest vacuum,20 oxide films can in some cases be removed by suitable vacuum annealing. Electrolytically polished and annealed surfaces, being relatively without strain, smooth and free of bulk oxides, were considered adequate for the present sorption experiments. Measurement of the surface composition of a solid-vapor couple presents a unique problem. Since experiments to determine the approach to equilibrium of the surface composition must be performed at temperatures where diffusion is very slow, solute penetration is so small that conventional analytical methods are unsuitable. An optical reflectivity method utilizing a polarization spectroscope was employed because of the relatively small penetration (~200A) of visible light in metals. By this method, elliptically polarized light reflected from the metal surface was analyzed and compared with that reflected from samples of known composition. The a phase of the copper-zinc system was

Jan 1, 1962

By M. E. Wadsworth, K. C. Bowles, H. E. Flanders, R. M. Nadkarni, C. E. Jelden

The kinetics of precipitation of copper on iron of various purity were carried out under controlled conditions. The rate of reduction has been correlated with such parameters as copper and hydrogen ion concentration, geometric factors, flow rate, and temperature. The character of the precipitated copper as a function of flow conditions and rate of PreciPitation has been observed under a variety of conditions. ThE precipitation of copper in solution by cementation on a more electropositive metal has been known for many years. Basile valentine' who wrote Currus Triumphalis Antimonii about 1500, refers to this method for extraction of copper. Paracelsus the Great2 who was born about 1493 cites the use of iron to prepare Venus (copper) by the "rustics of Hungary" in the "Book Concerning the Tincture of the Philosophers". Agricola3 in his work on minerals (1546) tells of a peculiar water which is drawn from a shaft near Schmölnitz in Hungary, that erodes iron and turns it into copper. In 1670, a concession is recorded4 as having been granted for the recovery of copper from the mine waters at Rio Tinto in Spain, presumably by precipitation with iron. Much has been published in recent literature on the recovery of copper by cementation, the majority of the articles being on plant practice.5-24 The rest include articles on investigation of the variables involved25-28 and a review of hydrometallurgical copper extraction methods." This literature has established: a) The three principal reactions in the cementation of copper are Cu + Fe — Fe+4 +Cu [ 11 One pound of copper is precipitated by 0.88 lb of iron stoichiometrically. In actual practice about 1.5 to 2.5 lb of iron are consumed. 2Fe+3 + Fe — 3Fe+2 [21 Fe +2H'-Fe+2 + H2 [3] Reactions [2] and [3] are responsible for the consumption of excess iron. Wartman and Roberson'28 have established that Reactions [ I] and [2] are concurrent and much faster than Reaction [3]. b) Acidity control is important in the control of hydrolysis and the excessive consumption of iron. he commercial workable range is approximately from pH = 1.8 to 3." c) Iron consumption is closely related to the amount of ferric iron in solution. Jacobi" reports that, by leaving the pregnant mine waters in contact wi th lump pyrrhotite (Fe7S8) for 3 hr, all the iron was reduced to the bivalent condition and scrap iron consumption was cut to 1.25 lb scrap per pound of copper precipitated. He also reported that SO2 has been used successfully to reduce ferric iron to the ferrous state. d) The ideal precipitant is one that offers a large exposed area and is relatively free of rust. e) High velocities and agitation show a beneficial effect upon the rate of precipitation, as it tends to displace the layer of barren solution adjacent to the iron and also dislodges hydrogen bubbles and precipitated copper to expose new surfaces. Little work, however, has been published on the reaction kinetics of copper precipitation on iron. Cent-nerszwer and Heller20 investigated the precipitation of metallic cations in solutions on zinc plates. They found the cementation reaction to be a first-order reaction. The rate constant was independent of stirring for high stirring rates and they concluded that the rate is governed by a diffusional process at low stirring speeds and by a "chemical" process at higher stirring speeds where the rate reaches a constant value. This conclusion has been challenged by King and Burger30 who could not find any region where the rate was independent of the stirring speed, although the rate constant they had obtained for high stirring speed was greater than the maximum value of the rate constant reported by Centnerszwer and Heller (by a factor of six). King and Burger, therefore, concluded that the rate of displacement of copper was controlled only by diffusion. Cementation of various cations on zinc has been summarized by Engfelder.31 APPARATUS A three-necked distillation flask of 2 000-mm capacity was used as a reaction vessel. A pipet of 10-mm capacity was introduced through one of- the side necks, the sample of sheet iron, mounted in a rigid sample holder, through the other, the stirrer being in the middle as shown in Fig. 1. The whole assembly was immersed in a constant-temperature bath. The stirrer was always placed at the same depth in the solution. EXPERIMENTAL PROCEDURE Reagent-grade cupric sulfate (J. T. Baker Chemical Co., N.J.) was used to make up a stock solution containing 10 g of copper per liter which was then diluted to various concentrations as required. Experimental data were obtained by measuring the amount of copper and iron ions in solution at successive time intervals. The initial volume of the solution was always 2000 ml, 10-ml aliquots being removed each time for chemical analysis. Because the total volume change of the solution was less than 10 pct, no correction was used for solution volume change. Nitrogen was bubbled through the solution before and

Jan 1, 1968

TO THE BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS. GENTLEMEN: Submitted herewith are the report of the Treasurer for the year 1941 and re¬ports for the same year of the following standing committees: Admissions, Mem¬bership, Papers and Publications, Mining and Metallurgy (Magazine), Library, and Student Relations. These reports present additional details. Membership For the fourth year in succession, mem¬bership reached a new all-time high, level as shown in Table 1. The total at the

Jan 1, 1942

By Henry J. Welge

The approximate methods which are now in use for calculating oil displacement from reservoirs by gas-cycling or gravity-drainage at constant gas pressure, or by water flooding, make use of fundamental relationships derived by Leverett' and Buckley and Leverett.2 The mathematical equations needed are derived by applying Darcy's law to the flowing phases, and by material balance considerations. ln general, any treatment of this type gives. for any particular exploitation time considered, a plot of oil saturation against distance in the reser-voir. The oil recovery must then be obtained by integrating in some manner the area under the plot. A useful analytical method has been derived for computing the average saturation, and hence the oil recovery. Use of this method simplifies the calculations because it makes unnecessary any numerical integrations. and even the saturation distribution plots are not needed. A further advantage of the method is that knowledge of the relative permeabilities is required only for a limited and intermediate saturation range. In both the Buckley and Leverett method and the method discussed here, a linear sand section is assumed, and in the case of gas drive the gas pressure is assumed sufficiently constant both with respect to reservoir position and time so that changes in gas density. solubility, or reservoir volume factor are negligiklle. Thus, the exploitation contemplates oil displacement as by an immiscible phase. Examples are given to illustrate how the new method can be used. INTRODUCTION AND THEORETICAL BACKGROUND This paper treats a simplified method for computing oil recovery when the oil is displaced, from the reservoir sand by a fluid which, within the limits of accuracy desired, can be assumed to be incompressible and immiscible with the oil. The method makes use of two basic relations originally developed for the case of water displacing oil. However, the case of gas displacing oil saturated with gas at a constant (or nearly constant) pressure may also be considered a displacement by an immiscible fluid. This is possible for the reason that the concentration of the gas in the oil never changes if tile pressure is fixed. consequently, any additional free gas must remain undissolved in the oil, and so must act essentially as an immiscible phase. For convenience, the cape of gas drive will be considered first. Both of the two basic relations needed refer to a linear reservoir, or one which may be somewhat idealized so that a constant cross-section is exposed to fluid flow. Further, the displacing phase is injected at one end, or face; of the reservoir, while the produced fluids are understood to emerge at one point only. which is the opposite face of the reservoir. As indicated in Fig. 1, the reservoir may he inclined by some angle 8. The first of the required equations may be derived by applying Darcy's law to both displacing and displaced phases, and subtracting the two equations. The result for water drive has been given previously, as Equation (13) of the reference by

Jan 1, 1952

By James K. Stanley

WHEN a plastically deformed metal is heated to a certain temperature, it undergoes a complete change in microstructure, the consequence of which is a marked alteration of mechanical properties such as hardness, strength and ductility. This change in microstructure occurs by recrystallization and is a process involving the formation and growth of strain-free nuclei in the deformed matrix. These nuclei continue to form with time and grow until a new grain structure replaces the cold-worked structure. The formation of the nuclei in the deformed sheet of 1 per cent silicon ferrite is illustrated in Fig. 1. If a recrystallization is conducted isothermally, a measurement of the fraction of the matrix recrystallized plotted against time leads to an isothermal recrystallization curve, first established in 1942.1 Such recrystallization curves are shown in Fig. 4. These curves show that the recrystallization of a cold-worked metal is best considered as a rate process rather than a time independent process such as is suggested by the improperly named and misleading recrystallization diagrams involving deformation, temperature, and grain size. 2-5 Any study of the rate of recrystallization resolves itself into a study of the component rates of nucleation and growth. The previous paper' provided an account of the determination of the rates of nucleation; N, the number of nuclei formed per unit time per unit of unrecrystallized area, and growth, G, the radial growth in unit time, in the recrystallization of silicon ferrite (1 per cent Si). A method was developed to furnish experimental data for evaluating the effect of the recrystallization variables on N and G. The mathematical analysis for the derivation of the isothermal recrystallization curve was developed for a two-dimensional case (in thin sheets where the diameter of the recrystallized grain is greater than the sheet thickness). The present paper is a continuation of the study of recrystallization of 1 per cent silicon ferrite begun in 1942.1 In this work the effect of the factors deformation, temperature, grain size, composition, and recovery is studied with respect to the rates of nucleation and growth. At the same time it is shown how the cooperation of N and G affects the isothermal recrystallization curve. The study of these variables on N and G has a definite bearing on the mechanism of recrystallization and should lay a foundation for a rational theory on the subject. PROCEDURE The procedure used in these experiments was essentially the same as that described previously but in certain details some changes were made in the interests of speed. With few exceptions, the procedure is the same for the study of all the variables. Where the procedure is different from standard manipulations attention is called to this fact.

Jan 1, 1945

By E. T. Turkdogan, L. J. Martonik, R. J. Fruehan

Electrochemical measuretnents of the solid oxide electrolyte galvanic cells CY-Cr2O3 I ZrO2 (CaO) 1 O (in Fe alloy) CY-Cr2O3 I Tho2 (Y2O3)I O en Fe alloy) have been made at 1600°C (2912°F) in order to test the Performance of such cells at liquid steel temperatures. The oxygen pvobe (cell) consists of a disk of ZrO2 (CaO) or Tho2 (Y2O3) electrolyte fused at one end of a silica tube filled with a mixture of Cr-Cr2O3 which is the reference electrode. Upon immersion in liquid steel, the electromotive force readings achieve a steady value within a few seconds, and remain steady for 30 win or more. The perforwzance of the probes has been tested using Fe-O, Fe-Si-O, Fe-Cr-O, Fe-V-O, and Fe-Al-O alloys; the oxygen contents of liquid steel derived from the measured electromotive forces are in satisfactory agreement with those determined by arulysis. Use of the probe in the deoxi-datiorz of steel, in laboratory experiments, is discussed. The results indicate that there is insignificant electronic conductivity in ZrO2(CuO) at oxygen activities down to those corresponding to 10 ppm in steel. At lower oxygen activities, probes tipped with ThOn (Y2O3) disks perform satisfactorily at oxygen activities down to 1 ppm O or less. THE key to the control of deoxidation of steel is a sensing device to measure rapidly the concentration of oxygen in liquid steel in the furnace, ladle or tun-dish at any desired stage of deoxidation. The analysis of the cast steel by the neutron-activation or vacuum-fusion method gives total oxygen as oxide and silicate inclusions. This analysis is important for guidance to steel cleanliness; however, such a postmortem is of little value in the control of deoxidation of liquid steel. At the General Meeting of the American Iron and Steel Institute in New York, 1968, Turkdogan and Fruehan' presented a paper on the preliminary results of the work done in this laboratory on rapid determination of oxygen in steel by an oxygen probe. Details of the work done in this laboratory leading to the development of a galvanic cell for the determination of oxygen in liquid steel, and the results of the tests made are given in this paper. It was through Wagner's contributions, since the early Thirties, to the physical chemistry of semiconductors in general that it ultimately became possible to construct galvanic cells for application at high temperatures. In 1957, Kiukkola and wagner2 successfully demonstrated the use of several solid electrolytes in measuring the free energies of several chemical reactions, in particular, the use of lime-stabilized zir-conia in high-temperature oxidation reactions. Starting 7 years later, a number of papers appeared in the technical literature3-' demonstrating possible applicability of galvanic cells for the determination of oxygen in liquid steel. In the earliest work, Japanese investigators3j4 experimented with various types of reference electrodes, e.g., graphite-saturated liquid iron at 1 atm CO or Ni-NiO mixtures; the results obtained, though promising, were not of sufficient accuracy. Except for the work of Baker and West,6 all other investigators5,7,8 showed that ZrO2(CaO) electrolyte could be used for this purpose. The main part of the galvanic cell used by Fischer and ~ckermann' and by schwerdtfeger7 (the latter work was done in this laboratory), consisted of a ZrO2(CaO) tube, -1 cm ID, closed at one end, with a platinum contact wire fixed mechanically inside the closed end. The tube was flushed with a gas of known oxygen partial pressure, e.g., air, CO-CO2 or H2-CO2 mixtures; gas along with the platinum lead wire served as the reference electrode. The oxygen contents derived from measured electromotive forces agreed reasonably well with the oxygen contents determined by vacuum-fusion analysis. It is evident from recent investigations that the electromotive force technique using a solid oxide electrolyte is fundamentally well suited for the determination of oxygen in liquid steel. However, it is equally clear that the cell arrangement of the type as commonly used is in need of considerable improvement, as it exhibits several shortcomings for industrial and even laboratory use. 1) Because of its size, the zirconia tube, though stabilized, has a poor resistance to thermal shock. 2) Fine pores and microcracks, which are invariably present in zirconia tubes, are detrimental to the satisfactory operation of the cell, particularly when gas reference electrodes are used. 3) Air or carbon dioxide reference electrodes give rise to high electromotive force readings; as a result, the determination of oxygen in steel becomes less accurate. For higher accuracy, the oxygen partial pressure of the reference electrode should be in the range similar to that of oxygen in steel. 4) Even in laboratory experiments, difficulties are experienced when flushing the tube with gases and maintaining the proper gas flow rate. Fischer and Ackermann,' who used air as the reference electrode, reported that when the flow rate was too low, furnace gases would leak into the electrolyte tube, therefore lowering the oxygen potential and measured electromotive force. The required flow rate in order to avoid leakage depended on the tightness of the electrolyte tube which varied with different tubes, thus making it difficult to predict in advance the required flow rate. However, if the flow rate is too high the inside wall of the electrolyte tube would be cooler than the wall

Jan 1, 1970

By J. L. Gillson

THE big mass of anorthosite in the Lake Sanford district and the bodies of titaniferous magnetite that occur in a small area near the south margin of the mass have been described repeatedly, and the puzzling problems of the genesis of the rocks and ores have stimulated the deductive reasoning of geologists for a hundred years. Some of these men have taken a leading part1-15 in describing the anorthosite rock and forming hypotheses concerning its origin; some have contributed most to the study of the ore deposits;'"= and some have made classical Studies3,4,21-27 introducing a basic approach to the problems of the anorthosite rock and genesis of the titaniferous magnetites. Much of the writing on the problems of rock and ore genesis has been based on physical-chemical reasoning rather than on field and microscope observations of the rocks and ores. Most of these geologists conclude that the anorthosite was formed by true magmatic crystallization, involving previous settling or squeezing out of ferromagnesian minerals from the parent magma. The associated gabbro is a separate segregation or later intrusion, and the lighter colored and finer grained facies of the anorthosite is either a chilled border zone of the anorthosite or the result of granulation by crushing of the coarse, dark blue rock of the main mass. This blue rock, called the Marcy type, is named after the higest peak in the range. The finer grained and lighter colored rock is called the White-face, after another mountain appropriately named for a cliff colored by this facies of the anorthosite. In explaining the genesis of the ores the authors have reached no general agreement, but all consider them to be dominantly the result of magmatic processes rather than the result of replacement by pneu-matolytic or hydrothermal processes. However, in the conclusions of two authors, Osborne27 and Ste-phenson," the reader is told positively that the ore minerals were introduced after the wall rock was solid and also that the oxides are later than the silicates. This seems to mean that the ore came in as a later intrusion, like a dike, since Osborne speaks of filter pressing and later injection of a residual magma. Stephenson agrees in general with Osborne but disagrees with his conclusion that ore does not grade into country rock. Singewald22 calls in "mineralizers" to participate in magmatic deposition. Stephenson ends his paper with a statement that replacement was the dominant process for the introduction of ore with anorthosite. Hence both Singewald and Stephenson call on pneumato-lytic or hydrothermal processes to supplement magmatic crystallization from a silicate melt, but they cannot quite bring themselves to state that the orebodies formed in that way. In their conclusions the ores are still magmatic segregations and magmatic injections and—almost as an afterthought— "replacements." According to Bateman18 there was a gravitational accumulation process of the iron silicates and oxides, which were injected later. Rambere explains the ores entirely on physical-chemical theory, as does Evrard.17 Buddington and associates,10 in a paper presented to the Geological Society of America in 1953, believe the facts observed prove that the magnetite-ilmenite formed at magmatic temperatures. The present writer's conclusions, given here, were first presented in 1947 in Industrial Minerals and Rocks.= Since the papers of Ramberg, Bateman, and Buddington, published after 1947, gave no recognition to those conclusions that differ from their own, the writer has taken an opportunity to restudy the area in the field, and to examine a number of microscopic sections, and now presents the evidence more thoroughly than he had an opportunity to do in the

Jan 1, 1957

By S. F. Reiter, W. R. Hibbard

A survey of the effect of heat treatment on the room temperature hardness of Fe-Mo alloys has been made. Constant strain rate tensile tests were performed between room temperature and 1800°F. These data were analyzed to determine the effect of temperature and composition on the strain hardening coefficient and strain rate sensitivity. Constant load creep-rupture tests were made on these alloys and the results related to composition and structure. A relation between the high temperature strength of the precipitation hardened alloys and the volume of precipitate has been observed. IN view of the extensive use of ferritic materials at elevated temperatures, it is surprising to note the limited amount of information relating the variables of plastic deformation, i.e., composition, structure, temperature, stress, strain, and strain rate. Hollomon and Lubahn' showed how the several variables of plastic flow might be treated analytically. No data were available on carbon-free iron and its alloys in a form suitable for this analysis. Several German investigations2-" constitute most of the experimental work relating high temperature properties to the constitution of these types of materials. In order to obtain new data, the iron-rich alloys of the Fe-Mo system were selected for detailed investigation for the following reasons: 1—Some of the important effects of molybdenum on the mechanical properties of iron have already been studied.' , 821 2—By suitable heat treatment of selected alloys, it is possible to study strengthening effects of four types: AT -a transformation, B—substitutional, C—precipitation, and D—dispersion of hard inter-metallic compound. Materials and Treatment Four-pound ingots were vacuum cast, employing the same melting schedule previously used.? The raw materials were electrolytic iron and lamp-grade molybdenum. The ingots were forged to l/z in. sq. rod and one portion swaged to 0.350 in. diam rod for the production of 1 15/16 in. long button-head specimens. The button-head specimen blanks were solution treated for 16 hr at 2100°F in hydrogen of —70°C dewpoint and then water quenched. They were subsequently plunge ground to the standard 0.160 in. diam test bar. Micrographs of the solution treated alloys are given in Figs. la through Id. The higher molybdenum alloys contained large equiaxed ferrite crystals similar to those in Fig. Id. A portion of the % in. rod was hot rolled to 0.100 in., sandblasted, and cold rolled to 0.020 in. Strip tensile specimens having a 0.020x0.200 in. cross-section and a 2.25 in. gage length were machined from the sheet. The alloys containing molybdenum were subsequently annealed 1 hr at 1560°F. The iron strip was annealed 4 hr at 1300°F in wet hydrogen. The resultant structures are shown in Fig. 2a through h. The ASTM grain sizes were 1 to 3 as solution heat treated or 3 to 4 as annealed. The chemical analyses of the alloys are given in Table I. Carbon contents were obtained after the heat treatments in hydrogen. Alloy 15.9 pct Mo was tested as a cast alloy.'

Jan 1, 1956

"The reduction works of the Boston & Montana Reduction department, near the north end of this dam is one of the reduction plants belonging to the Anaconda Copper Mining Company, the other being at Anaconda. These works employ about 1,100 men and have a capacity of about 3,800 tons of crude ore per day. This plant is now being remodeled to embody results of experiments and investigations which have been made with a view to more economic.al treatment of ores. A brief description of the plant as it will be after the remodelling is as follows:Concentrator Department: Consists of six units or sections, each section treating from 550 to 600 tons of crude ore per day. This department is not being. remodelled at the present time. A concentrating process, however, has been developed and partially installed in the old mill, and an experimental section embodying this concentration process has also been installed at the concentrator at Anaconda."

Jan 1, 1913

By T. D. Murphy

This chapter deals with those types of silica raw materials that have been segregated and refined by natural processes into nearly monomineralic deposits and hence, by virtue of their high degree of purity, have become the sources of commodities having special and somewhat restricted commercial uses. In some instances, these raw materials occur in nature as unconsolidated quartzose sand or gravel and can be exploited and used with very little preparation and expense. More often, they occur as sandstone, conglomerate, quartzite, quartz mica schist, or massive igneous quartz which must be crushed, washed, screened, and sometimes chemically treated before commodities of suitable compositional and textural characteristics can be successfully prepared. The occurrence and distribution of silica raw materials is summarized and an effort has been made to bring commodity definitions, critical properties, and specifications up to date. Presentation of mining and processing methods is considered beyond the scope of this article; they are, for the most part, conventional and well known. New production techniques are currently reported in the trade journals and are later adequately described in technical publications as promptly as competitive restrictions allow. Discussion on Basis of Use ABRASIVE USES Industrial silica used for abrasive purposes falls into three main categories: (a) blasting sand; (b) glass-grinding sand; and (c) stone-sawing and rubbing sand. Blasting sand is a sound closely-sized quartz sand which, when propelled at high velocity by air, water, or controlled centrifugal force, is effective for such uses as cleaning metal castings, removing paint and rust, or renovating stone veneer. It is commonly referred to as Sand Blast sand. Multicycle quartz sand is an efficient blasting agent by merit of its survival characteristics which are soundness, toughness, and hardness. Steel grit and shot have supplanted it to a large extent but owing to their higher cost and tendency toward deterioration in storage, are still not universally used. It is conceded that angularity promotes faster cutting but this is offset by a higher loss in fines. The peening action of a rounded grain is a desirable feature in achieving a satin finish for certain light metal castings but a subangular grain is unsurpassed for fast heavy cutting. Specifications are chiefly based on size frequency distribution but it is mandatory that the grain be free of adhering clay or irony coatings. Material that dusts upon handling will not be tolerated. There is no uniform trade designation for the many blasting sand grades. Most producers sell on the basis of numbered grades; that is, No. 1, No. 2 and so on, this generally connoting fine to coarser grades. Designation of grade by the two sieve sizes between which most of the material lies, is practiced in some areas. Thus, in a No. 1220 grade, 98 pct of the material passes a 12 mesh sieve and is retained on a 20 mesh sieve. Blasting sand specifications vary according to use. Coarse grades range from 4 mesh to 12 mesh, medium grades range from 12 mesh to 30 mesh, finer grades may range from 20 mesh to 100 mesh or finer. Specifications generally call for narrow limits of gradation, requiring precise sizing methods. The fact that most blasting sands are retained

Jan 1, 1960

By H. [Eyring], B. J. Zwolinski

[ ] The authors are to be commended for their excellent work on the activities of components in the solid state. It is, however, felt that certain points require clarification with reference to diffusion in the solid state. It is a well established point that any rate process in a non-ideal system can be expressed by the general equation [ ] where ko is the specific rate in an ideal system, and ?A, ?B ... , the activity coefficients of the reactants and ?± and ?M,?N the activity coefficient of the activated complex and the intermediates, respectively. With reference to diffusion, the following simplified treatment in correcting for non-ideality is proposed. The same free energy change is involved in moving a particle from a solution of one activity to a solution of another activity,

Jan 1, 1947

By P. Pietrokowsky, T. E. Tietz, J. E. Dorn

The amount of solid solution hardening in aluminum alloys was found to be dictated by two factors: the lattice strain, and the change in the mean number of free electrons per atom of the solid solution. To obtain this correlation it was necessary to assume that aluminum contributes two electrons per atom to the metallic bond. WHEN the modern scientific method of analysis was first being formulated, Francis Bacon recorded in his "Essays" (circa 1600) that "an alloy . . . will make the purer but softer metal capable of longer life." During the intervening centuries voluminous data have been reported which demonstrate that the additions of alloying elements do in fact increase the hardness and strength of the pure metals. Nevertheless, the significant details of this problem on the unique effect of each element toward enhancing the mechanical properties of alloys only recently have been subjected to systematic scientific scrutiny. The major objective of this investigation is to determine how minor additions of alloying elements affect the plastic properties of polycrystalline aluminum alloys. By means of such studies it is hoped to provide not only data on the solution strengthening of aluminum alloys, but also a body of facts which will supplement the knowledge already available on the factors responsible for solution hardening in general. A review1"10 and analysis1' of the existing data on the effect of solute elements on the plastic properties of solid solutions reveal that our current knowledge on solid solution hardening is somewhat meager, inconsistent, and inconclusive. Many of the inconsistencies are undoubtedly attributable to the influence of unsuspected factors, such as purity; or uncontrolled factors, such as grain size, on the plastic properties of alloys. Nevertheless the following conclusions might be tentatively accepted: 1. Addition of solute elements invariably increases the yield strength, tensile strength, and hardness of the host element. 2. The rate of strain hardening, in general, increases with the concentration of the alloying element. 3. The strengthening effect in ternary alloys is the sum of the individual strengthening effects of the two solute elements as measured in their binary alloys. 4. The lattice strain is one factor that affects the strengthening of the alloy but it is not the only factor. 5. A second factor might be the difference in valence between the solute and solvent metals. All of the available evidence is in complete agreement with the first conclusion; the remaining conclusions, however, are not in agreement with all of the published data, but, in each case, the major weight of the existing evidence favors these deductions. Additional investigations will be required before most of these tentative conclusions can be accepted without reservation. In the following report an extensive investigation of the plastic properties of binary aluminum alloys is described. This work was undertaken in an attempt to shed more light on the general problem of solid solution hardening. Materials for Test: Aluminum was selected as the solvent metal for the present investigation on the effect of solute elements on the plastic properties of alloys. This choice was made for several reasons: (1) There appears to be little fundamental data in the published literature on the effect of solute elements on the properties of high-purity aluminum alloys. In view of the ever increasing economic importance of aluminum, such data would be of basic interest to the metallurgists concerned with the development of new aluminum alloys. (2) Aluminum is thought to be only partially ionized in the metallic state1' and consequently it might provide more complex relationships of the mechanical properties with the concentrations of the solute elements than more simple fully ionized solvents would reveal. (3) The data on aluminum alloys will provide a broader basis for correlations between the mechanical properties of metals in general and the concentration and atomic properties of the solute elements than is now available. Some complications, however, attend the selection of aluminum: The solubility of the various elements in the alpha aluminum phase are quite restricted, and not always well known. Consequently, only dilute solid solutions are available for study. This, however, may be somewhat advantageous because the dilute solution laws presumably are simpler than those applying to concentrated solutions. In addition, strain-hardened pure aluminum is known to recover at atmospheric temperatures. Very likely its alloys exhibit slower recovery rates. Thus, the secondary factor of effect of alloying elements on recovery might complicate the data. Such compli-

Jan 1, 1951

By C. D. Woodward

The Anaconda Copper Mining Co. purchases 25,000 kw. of electric power for its mining operations at Butte, Mont. This power is delivered, over duplicate feeders, in the form of 60-cycle, 2400-volt, three-phase current, to five compressor plants, where most of the energy is used for driving air compressors. At the compressor plants are located the switching apparatus for controlling the 2400-volt power and distributing it to the various mines. At these points, also, there are a number of motor-generator sets for converting the alternating current to 275-volt direct current for the haulage systems. Pole lines convey the powcr from the compressor plants to outdoor transformer substations at most of the mines. When it is not economical to distribute the power at the lower voltages in the mines, transformers and motor-generator sets are placed at strategic points underground. All power is purchased on a maximum-demand basis; therefore there is installed at one of the compressor plants an eight-element totalizing graphic wattmeter. This instrument records simultaneously the value of all power taken at the numerous points of delivery, which not only climinates the diversity factor but permits load dispatching between compressor and pumping plants, and thus materially reduces the maximum demand from the power system. As most of the mine hoisting is done by 90-lb. compressed-air winding engines, the air-compressor equipment for the winding engines and mining operations is quite extensive. The standard air compressor has a rating of 7500 cu. ft. per min. of free air, and most of the compressors are directly connected to synchronous motors. The synchronous motors are designed for 80 per cent. loading power factor, thus facilitating power-factor correction of total mine load. Consequently by cooperation with the power company, the voltage of the power received at the compressor plants is constant. In the mines there are installed an induction motor load of approxi-mately 10,000 hp., and 4500 kv.-a,, in transformer capacity. It is the practice to install 2200-volt motors in the mincs, except those rated below 50 hp, hence there are in operation underground about 5000 hp., in the

Jan 1, 1923

By C. D. Woodward

The Anaconda Copper Mining Co. purchases 25,000 kw. of electric power for its mining operations at Butte, Mont. This power is delivered, over duplicate feeders, in the form of 60-cycle, 2400-volt, three-phase current, to five compressor plants, where most of the energy is used for driving air compressors. At the compressor plants are located the switching apparatus for controlling the 2400-volt power and distributing it to the various mines. At these points, also, there are a number of motor-generator sets for converting the alternating current to 275-volt direct current for the haulage systems. Pole lines convey the powcr from the compressor plants to outdoor transformer substations at most of the mines. When it is not economical to distribute the power at the lower voltages in the mines, transformers and motor-generator sets are placed at strategic points underground. All power is purchased on a maximum-demand basis; therefore there is installed at one of the compressor plants an eight-element totalizing graphic wattmeter. This instrument records simultaneously the value of all power taken at the numerous points of delivery, which not only climinates the diversity factor but permits load dispatching between compressor and pumping plants, and thus materially reduces the maximum demand from the power system. As most of the mine hoisting is done by 90-lb. compressed-air winding engines, the air-compressor equipment for the winding engines and mining operations is quite extensive. The standard air compressor has a rating of 7500 cu. ft. per min. of free air, and most of the compressors are directly connected to synchronous motors. The synchronous motors are designed for 80 per cent. loading power factor, thus facilitating power-factor correction of total mine load. Consequently by cooperation with the power company, the voltage of the power received at the compressor plants is constant. In the mines there are installed an induction motor load of approxi-mately 10,000 hp., and 4500 kv.-a,, in transformer capacity. It is the practice to install 2200-volt motors in the mincs, except those rated below 50 hp, hence there are in operation underground about 5000 hp., in the

Jan 1, 1923

By Foster Fraas

INTRODUCTION THAT variations in the humidity of the air and in the moisture content of a mixture of broken solids being separated electrostatically cause trouble is not new.1 Much of the reputation for unreliability commonly ascribed to the electrostatic separation processes is probably due to this one factor alone. Some operators dry thoroughly before separating; and while this is good in many instances, there are others in which it is not the remedy for trouble. Some mixtures behave best in very dry air and with the mixtures fed to the separator while hot to reduce the adsorbed water content. On the other hand, an overdried mixture on coming to equilibrium with more humid air, has been known to take up moisture selectively on one family of particles, as of coal in the presence of slate and clay, and give sharper electrostatic separation. From these observations it is concluded that there is a permissible moisture content for a particle and also for the atmosphere surrounding it, if in equilibrium, at which the particle will have a conductivity or contact potential2-4 that is ideal for electrostatic separation. This permissible moisture content varies between a wide range of limits for the different materials that are separated and with the kind of electrostatic separating process used. Water can be present as a result of adsorption and condensation from the atmosphere, as an accumulation before or during mining, or as a residue from a previous process step. The water may exist as a liquid film or as an adsorbed layer of vapor. If the water exceeds permissible limits it must be removed. Its state determines the method. Drying by evaporation is necessary for adsorbed water, for part of the liquid-film water (that is, up to several percent of the dry weight), and for free water in the internal structure. Large water contents may be removed by drainage or filtration. At just what point mechanical removal should cease and drying by evaporation begin depends upon the method of mechanical removal and its cost. Particles can also be separated according to their differences in dielectric constant when suspended in a liquid of intermediate dielectric constant. Recovery of this liquid presents a similar problem. PERMISSIBLE MOISTURE The adsorbed moisture on the outer surface of minerals can be quickly removed or replaced. Accordingly, in speaking of adsorbed moisture contents, either that of the solid or that of the surrounding air may be considered, the two values being connected by a distribution coefficient which varies with the temperature. However, such a condition does not necessarily exist in processes where an initially dry material is suddenly introduced into an atmosphere having a partial pressure of water vapor or where a moist material is suddenly introduced into a dry atmosphere. Here the resultant differences in the

Jan 1, 1947

By Arthur Baker III

The orebodies are long bedding-plane lenses of chalcopyrite and sphalerite, associated with garnetite masses. Most of the orebodies are within a 50-ft thickness of Cambrian limestone; other Paleozoic limestones and dolomites are locally metamorphosed but only slightly mineralized. Pre-mineral faults are numerous, but shallow folds were the main ore-localizing structures. JOHNSON camp is in the northwestern part of Cochise County, Ariz., about 50 miles east of Tucson. The nearest major mining districts are Tombstone and Bisbee, respectively 27 and 50 miles to the south, and the Superior-Miami-Globe-Ray porphyry copper group, about 90 miles northwest. Like many mining camps of the Southwest, Johnson camp is said to have been worked by the Spaniards. The first production on record was in the early 1880's, when an unknown amount of oxidized copper-silver ore in the Peabody mine was mined from replacement orebodies in the Pennsyl-vanian Naco formation. From 1904 to 1911 outcropping oxidized ores in the Cambrian Abrigo formation were worked, and an estimated 100,000 tons of copper ore were shipped. In 1912 the first large sulphide orebody of the district, the Republic Manto orebody, was discovered, and in the following few years some 250,000 tons of predominantly sulphide ore were shipped. The average grade of this ore was approximately 4.5 pct Cu, 6 pct Zn, 0.8 oz. Ag, and 0.001 oz Au. The Republic, Copper Chief, and Mammoth mines were the principal producers during this period. Mining ceased in the district after 1920, and until 1943 only small-scale leasing operations were carried on. In 1943 all the mines that had been productive were acquired by the Coronado Copper and Zinc Co., the present operators, and in the 10 years since that time the district production has amounted to approximately 350,000 tons of milling ore averaging 2 pct Cu and 6 pct Zn. Most of this ore was produced from the Republic and Mammoth mines, but since 1950 a large part of the production has been from the new Moore mine. The total known production from the district, then, is about 3/4 million tons of copper and copper-zinc ore of low grade. All of this ore was produced from orebodies associated with garnetite in the middle member of the Cambrian Abrigo formation. In addition to this known production, an unknown tonnage of ore was extracted from the Peabody mine orebodies that lie in the Pennsylvanian Naco formation. Published information on the geology of the district is limited. Aside from brief references in various mining journals, only three papers on the district have been published.1-3 One of these is a U. S. Bureau of Mines report on a diamond drilling program, one is a brief paper on the general geology of the district, and the third is a report on geochemical experiments, with a section on the occurrence of the orebodies. The last two are by John Cooper, of the United States Geological Survey, who has done much detailed work in the area. Stratigraphy The rocks of the mineralized area are Paleozoic sediments ranging in age from Cambrian to Penn-sylvanian. Several disconformities are present in the stratigraphic column, the most important one being between the Cambrian Abrigo formation and the Devonian Martin formation. There are no angular unconformities. Within the district, the Paleozoic sediments lie in a fairly uniform monocline, striking northwest and dipping 30" to 50" northeast. This local monocline is part of a domal struc-ture centered in the Little Dragoon mountains to the southwest. The Texas Canyon stock, a quartz monzonite body intruded probably during the Laramide revolution, lies south of the mineralized area (Ref. 2, p. 33). The Paleozoic rocks dip away from the stock, and on the surface are separated from it by at least 1500 ft of Pre-Cambrian rocks. The outcrop pattern of the northeastern edge of the stock suggests that it may dip gently northeastward, passing below the mineralized area at moderate depth. No quartz monzonite has been found in mine workings or diamond drill holes, which reach to depths of 1000 ft. The only igneous rock found in the mineralized area is a lamprophyre dike cutting the Naco limestone in and near workings of the Peabody mine. With the exception of the lowermost beds—the Bolsa quartzite and the shaly lower member of the Abrigo formation—the Paleozoic sediments are predominantly carbonate rocks, Fig. 1. The middle member of the Abrigo formation, which contains the principal ore-bearing beds, is limestone, with thin shale partings throughout most of its 250-ft thick-ness. Near the top of this member is a sandy bed some 25 ft thick. The upper member of the Abrigo formation and the lower half of the overlying Devonian Martin formation are dolomitic, with num-

Jan 1, 1954

By C. S. Smith, E. W. Palmer

IN 1934, when Gregg and Daniloffl wrote their excellent monograph on the alloys of iron and copper, the most recent literature on the constitution of the alloys indicated a narrow single-liquid area for 20" above the liquidus with a closed liquid mis-cibility gap above this. Since that time, however, a number of investigators have confirmed the much earlier studies of Mushet2 and Stead3 who, among others in the nineteenth century, had described the true state of affairs. Liquid copper and iron are completely miscible in the absence of carbon, but small amounts of carbon cause liquid segregation. In 1934, one of the writers' mentioned evidence for the absence of liquid separation in carbon-free alloys at temperatures up to 1700°C. Two years later, Mad-docks and Claussen5 unequivocally established the absence of liquid segregation and published a revised diagram, reproduced in fig. 1. They also studied the limits of the two-liquid area in ternary alloys of iron, copper, and carbon as a function of carbon and iron content. In the same year Simpson and Bannister" and Schumacher and Souden7 described in some detail the properties of alloys containing 50 to 75 pct Cu. More recently Hodges et al.16 have developed the copper-rich alloys for use as high-strength conductors. In 1937, Iwase, Okamoto, and Ameniya8 published data on the miscibility gap in ternary alloys of iron, copper, and carbon that supported the conclusions of Maddocks and Claussen, and definitely located the two-liquid area at temperatures of 1450" and 1540°C. They also reported that additions of 1 pct Al, Ni, Pb, Sn, or Zn caused no segregation in 50 pct Cu alloys at 1540°C. The use of copper in amounts approximating 1 pct has found industrial employment to an increasing degree in both wrought and cast steels, for such steels are capable of being precipitation-hardened following normalizing, and have high yield strengths. This is summarized by Gregg and Daniloff,1 Sallitt,9 and Lorig and Adams,10 while Alexander" gives additional information on the heat treatment of copper-steel castings. Lippert12 has described Digby's two-phase steels containing copper and chromium. The work described in the present paper was done in the years 1932 to 1934, at which time much of the information was new. The excellent work subsequently done in other laboratories but more promptly published makes the present paper in part only a confirmation of what is now well known. There has not, however, been published any unified study of

Jan 1, 1951