Search Documents

By G. F. Fix

Oil and gas activity reached a higher peak in Indiana during 1940 than for any like period during the past decade. Major activity, as during 1939, was in the southwestern part of the state, the Indiana portion of the Eastern Interior Coal Basin, where most of the increase was due to field drilling in previously proven areas. The amount of wildcat drilling was about the same as for 1939. No new fields of any apparent consequence were discovered during the year, with the possible exception of the College pool, in southwest Posey County. Only one well had been completed in this area at the end of the year. About 10 ft. of saturated Aux Vases sandstone was drilled in this well and the initial production was I00 bbl. of oil a day. Other discoveries during the year 1940 include: St. Thomas, in southwestern Knox County, where four McClosky wells, ranging from I00 to 300 bbl. a day initially, were com-pleted; Buff kin, in central Posey County, with 11 oil wells and 5 gas wells completed; and new developments in two old areas —Randolph County (part of the old Trenton field) and Gentryville, northwestern Spencer County, where some oil was found many years ago. The St. Thomas field proved disappoint-ing, with very spotty production from the McClosky horizon of the St. Genevieve limestone at a depth of about 1875 ft. The discovery well flowed 362 bbl. a day ini-tially. At the end of the year the field was pretty well outlined by dry holes and some inside locations were dry. The Buffkin pool also proved spotty, with production from shallow Pennsylvanian sands and from the Basal Pennsylvanian Mansfield sandstone, the latter at a depth of approximately I175 ft., with small production from the Cypress sandstone of Chester age. Oil wells in this pool are small, ranging from 25 to 75 bbl. a day. The Randolph County area, on the east side of the Trenton gas field, showed some promise for a commercial gas field, with four completed gas wells having cumulative initial flows of about 1,200,ooo cu. ft. a day. The area appar-ently was not depleted during the Trenton boom at the turn of the century, since casing pressures are about as high as the virgin pressure in the old field. Elsewhere the pressure has dropped as low as 5 pounds. The Griffin field received most of the drilling during 1940, with 163 completed oil wells. This field now covers about 3200 acres on the Indiana side of the Wabash River and is not as yet completely delimited. It produced the major part of Indiana's oil during the year—a total of 3,594,000 bbl. At the end of 1940, there were 253 producing wells in Griffin. New Harmony had five completions for a total of 24. The Rockport field, in Spencer County, continued to be actively developed and had a total of 45 gas wells and 9 oil wells at the end of the year. Oil in commercial quantities had not been found in the field previous to 1940. Total gas production for the year was 394,470,000 cubic feet. In all, 521 wells were drilled in the state during 1940, as compared to 377 for 1939. Of this number 248 were oil wells, 77 were gas wells and 196 were dry. Divided into

Jan 1, 1941

R. B. BRINSMADE, Ixmiquilpan, Hgo, Mexico* (written discussion). As the discussion of Mr. Graton's paper by Messrs. Norris, Patterson, and Crane has been from the standpoint of the mineral land-value owners, a few remarks in the interest of the "under dog"-the average taxpayer and citizen-may prove timely. In my discussion of Doctor Raymond's Paper1 and of the papers of Messrs. Gibson2 and Godson, 3 have endeavored to demonstrate, from both political economy and history, that our existing system of unrestricted private ownership of land is incompatible with equality of economic opportunity and, therefore, subversive of our democratic political institutions. In Mr. Graton's paper, the same land problem is important, though camouflaged by the failure of the Federal income tax laws to distinguish between land and capital, in the requirements for valuation, or between earned and unearned incomes in the levying of taxes. I disagree with Mr. Graton's statement, on p. 2967, as follows: The immense majority of mining ventures are failures. A multitude of disappointments is relieved by occasional success. Were it not for the chance of great rewards, all the vitally necessary but mainly unremunerative work of exploration would not be undertaken. In contrast with nearly all other fields of endeavor, it is altogether unlikely that, on the whole, the gains in the successful mining ventures suffice to offset the losses in the unsuccessful.

Jan 3, 1920

By C. P. Watson

Economics has been defined as the useful application of wealth or material resources. The search of alchemists in the Middle Ages for s formula by which base metals might be transmuted into gold was no more intensive than has been the search by all branches of the oil industry for methods whereby the rnatcrial resources of West Texas in the nature of sulfur-bearing oil might be usefully applied. The purpose of this paper is to present in brief space developments that are conceded to possess economic significance. History The first discovery of oil in commercial quantities in the Permian Basin of West Texas was the Westbrook field in Mitchell County in 1920. Three years later the discovery well in the Big Lake field was cornpleted as a small pumper (70 bbl.) at a depth of 3028 ft. In 1925, discovery of the Powell or World pool in Crockett County stimulated activities in the Permian Basin, further establishing the importance of the Permian limestones as sources of production. The years 1925 and 1926 were marked by a period of extensive leasing and drilling activities. At the close of 1926 more than 7,000,000 acres had been leased and discovery wells completed in the Hurdle, Hendricksand Yates fields, definitely establishing the importance of the Permian Basin as a source of production from free-flowing wells. Review of Fields The producing fields in the Permian Basin are grouped on three distinct lines of folding. These may be separately identified as the Big Lake-Powell fold; the Yates, Hurdle, and Church-McElroy area and the Winkler County development. Production is derived from a porous limestone stratigraphically uniform, encountered at depths varying from 900 to 3100 ft. Lenticular sand bodies above the lime in Howard County have resulted in the

Jan 1, 1928

By Noel Cunningham

Many excellent descriptions of the mills of the Porcupine district have been written, but no discussion exclusively devoted to the metallurgical technology has been given. These notes are intended to cover this feature briefly. They are based upon 21/2 years' mill operation in the district—i.e., practically since the beginning of metallurgical operations. Character of the Porcupine Ore.—There is no oxidized ore in the district, the surface having been deeply planed by glacial action in recent geologic time. The precious-metal content is about in the proportion of 85 of gold to 15 of silver by weight; hence, the silver is practically negligible. There are two classes of Porcupine ore, having very different characteristics; these will be referred to throughout this paper as Class A and Class B. Class A ore is a pure quartz with inclusions of schist. Generally it is heavily fractured and breaks down readily to sharp, hard grains, about minus 10 plus 20 mesh, requiring further comminution to release the gold. It carries very little pyrite; the gold is entirely free and apt to be coarse, but often spongy, going into solution readily on that account. This gold is 60 per cent. to 85 per cent. free milling, depending on the grade of ore. Class B ore is an iron silicate schist, strongly laminated, carrying 4 to 5 per cent. pyrite; its specific gravity is 2.8 to 3.0, depending upon the amount of mineralization. In breaking the ore in the mine, generally over 25 per cent. of material through a 1/2-in. ring is made; the ore readily breaks down in milling and makes a comparatively large amount of non-crystalline slime; owing to its high specific gravity, however, it is quick settling. In my opinion, the gold in this ore is free, but so finely divided that it will neither pan nor amalgamate; it appears to be disseminated through the rock and not chiefly associated with the pyrite. Veins of Class A ore occur with or without side walls of Class B, and veins of Class B occur unassociated with Class A; more often the veins are closely banded, Class A and Class B alternating, generally with Class B in excess. Both classes of ore are more or less blocky at times, and with reference to Class B this is indicative of low gold content.

Jan 1, 1915

By Alfred W. Gauger, George A. Burrell

The senior author of this paper, while in Colorado on other official business, made a trip to the Cripple Creek gold-mining district to get more data than are at present available regarding the composition of the gas that issues from the rock into the mines of the district. This was done at the suggestion of George S. Rice, Chief Mining Engineer of the Bureau of Mines. There are -many questions of interest and importance in connection with the ventilation of the mines in the Cripple Creek district, such as the menace to life and mining of a suffocating gas entering the mines from the rock, the danger due to powder smoke (from blasting operations), and danger of continued inhalation of rock dust by the miners. This report confines itself to the first problem, the gas from the rock, and principally to one phase of this question, the composition of the gas and its effects on men and lights. A more thorough study of this and other ventilation problems is planned. That the rock gas is a real menace is shown by the fact that miners (variously estimated from 25 to 50 by different persons interviewed) have been killed by it in the 25 years that mining has been vigorously carried on at Cripple Creek. Many men have had narrow escapes from death, some of them having been incapacitated for days. In addition, much loss of time results because at certain periods of the year or on certain days it is impossible to enter some workings. At a few mines, fans force air into the workings, thus supplementing the natural ventilation and much improving conditions, but the improvement is not entirely adequate at all times. Origin of the Gas Lindgren and Ransome1 think that the gas found in the rocks of the Cripple Creek mining district represents the last exhalations of the ex-

Jan 1, 1917

By R. P. Alger, M. P. Tixier, D. R. Tanguy

In the combination induction-electrical log used at present in the field, the induction logging tool is appropriate for the investigation of moderately invaded formations. A new induction sonde with a radius and investigation about twice as large has been developed recently for the case of deep invasion. It has very nearly the same vertical resolution as the present sonde so that thin beds are defined as accurately as before. The characteristics of the new tool are described, the corresponding interpretation charts are given and field examples are discussed. The design of the sonic logging tool has been modified to improve the calibration and the reliability. The fact that porosity can be accurately recorded by means of the sonic log has prompted new interpretation procedures for saturation estimation, wherein the data concerning the various permeable beds in a given well are correlated. One approach consists of plotting transit time vs true resistivity, with an appropriate scale. With this approach, saturations can be estimated conveniently even in cases where formation water resistivity is not well known. In another approach, a comparison is made of the values of the formation waters computed from the re- sistivity and sonic logs. Using the concept of continuity, this procedure makes possible a quick determination of zones of saturation in shaly sands and/or in case of appreciable variations of formation salinities with depth. It has been found that the comparison of porosity from the sonic log with the apparent porosity computed from a short-investigation resistivity log may reveal, in many cases, the presence of residual oil and thus detect potentially productive formations; this procedure is valuable when the true formation resistivity and the resistivity of the formation water are in doubt. INTRODUCTION During the past year, the efficiency of log interpretation has been vastly improved. The improvements have largely resulted from the introduction of a deep-investigation induction device and from the application of new interpretation techniques that utilize sonic vs resistivity readings. Since the new interpretation techniques depend, in part, upon good values of true formation resistivity, the new induction log will be discussed under Part I. The sonic interpretation techniques will be studied under Part 11. Early in 1959, the 6FF40 induction equipment was introduced in the field. This device was designed for a better approach to true formation resistivities in deeply invaded zones. The greatly improved radial investigation of the 6FF40 equipment has been achieved without sacrificing vertical resolution. The first combination induction-electrical log, the 5FF40, was introduced as a standard tool in 1956 for the logging of wells drilled with fresh muds. The tool has received wide industry acceptance in the United States. 'The 5FF40 induction log has a radial investigation sufficient to overcome average depths of mud filtrate invasion. At 5d invasion, for example, the 5FF40 induction log will read about 1.4 R. in a water sand where R., = 10R,. At 10d invasion, such induction log would read 2.45 R. in the same water sand. In either case, the effects of invasion would not be sufficiently great to cause a water sand to be mistaken for a shale-free oil- or gas-producing zone. Some formations, however, invade deeply — in excess of 10d. Such water zones could be mistaken for oil-or gas-saturated sands unless the porosity balance' can clearly make the distinction. It is for these deeply invaded formations that the 6FF40 was developed. CHARACTERISTICS OF THE 6FF40 Radial Investigation Characteristics To describe the comparative responses of the 5FF40

Although Australia is the world's second biggest producer of iron ore, the last few years have not been easy for companies in Western Australia's Pilbara region (see map) where more than 90% of the nation's iron ore is produced. For at least two years, the industry has been plagued by dwindling markets abroad, production-crippling strikes at home, skyrocketing costs (well above the official 13% annual inflation rate), an acute shortage of investment capital, increasingly ferocious competition from foreign iron ore producers-and, as if all this weren't enough, by an over-valued currency that has caused incalculable damage not only to iron ore producers but to the entire mining industry of Australia. (This last problem was mitigated less than two months ago, on November 28, 1976, when the Australian dollar was devalued by a whopping 17 1/2%.)

Jan 1, 1977

By Robert F. Mehl, Edward L. McCandless

Oriented overgrowths and intergrowths among both metallic and nonmetallic substances have been recognized and studied for well over a century. The work of Widmanstätten in 1808 on the geometrical structure in meteorites, a structure known by his name, demonstrated that oriented intergrowths can occur in purely metallic systems. This fact led to much of the early microscopic study of alloys, contributing greatly to the advance of physical metallurgy. The problem has been attacked again in recent years in a comprehensive fashion, with the object of discovering what atomic movements may occur during phase changes in alloy systems. Much of this work has appeared in the A.I.M.E. Transactions in a series of papers published by Mehl and coworkers beginning in 19311. Although many aspects of this general problem remain unsolved, it may be said that the orientation of a new phase forming by precipitation from solid solution or by transformation invariably bears a unique relationship to the orientation of the phase from which it formed, and that similarity in atomic patterns on atomic planes in the two phases play an important part in determining the orientation relationship. Analogous orientation relationships exist in oriented intergrowths in nonmetallic systems—mineral or inorganic. In 1827 Haidinger2 discovered natural intergrowths of hematite and magnetite, and demonstrated that the rough form of the magnetite octahedrons was delineated by small crystals of hematite, of which the basal (00.1) planes lay parallel to the octahedral cleavage planes of the magnetite. The description of this orientation relationship was later completed by von Rath3, who showed that the edge (00.1): (10.1) in hematite lies normal to the [Ill]

Jan 1, 1937

By Walter C. Smith

THE Cerro de Pasco Copper Corp. began to produce bismuth at the Oroya smelter in 1929, at which time the only important consumption of that metal was in the manufacture, of pharmaceutical compounds, and the normal supply of metal exceeded the demand. With a new and major producer entering the field, additional uses for bismuth had to be developed. A survey indicated that the most promising opportunity lay in fusible alloys containing bismuth. A large number of bismuth alloys were known and a few of them were being used in the manufacture of automatic sprinkler heads and safety plugs. The literature cover in,- the- alloys was found to be sketchy and contradictory. Research, development, and educational work carrried on by the Corporation during the past fifteen years has resulted in greatly enlarged uses for the metal. In general the low-melting bismuth alloys are of high specific gravity, relatively soft, of low tensile strength, brittle to shock, yet subject to plastic

Jan 1, 1945

By R. G. Ward, A. E. El-Mehairy

A technique was developed to calculate the density of liquid metals from the profile of a weighed levitated drop obtained by emitted light photography and calibration. The density of liquid copper was determined over the temperature range 1370" to 2100°K and expressed with the equation: The molar volumes and thermal coefficients of expansion are calculated. Copper, upon melting, was found to expand 3.34 pct. A knowledge of the density of liquid metals is essential as it is a parameter appearing in most theories of the liquid state. The liquid density is also necessary for the calculation of the commercially important contraction occurring on solidification. Unfortunately good density values are rarely available and the present work was undertaken to establish a new method of density determination free from the limitations of the existing methods. For liquid metals with high melting points, the variation and the limited number of density values reported in the literature have been caused primarily by difficulties in technique, a matter which has been adequately discussed by Urbain.' In all the methods used for measuring the density of the high-melting liquid metals there are sources of error, and corrections have to be made. For example, in the method of balanced columns, the formation of gas bubbles in one or both arms was a great source of error. In the pyknometer3 and immersed-sinker methods, corrections of certain volumes for thermal expansion to the operating temperature exceed 4 pct. In the maximum-bubble method5 a correction for the thermal expansion of the bubble-tube is used (about 1.6 pct); a second correction takes into account the change in the volume of liquid displaced by the bubble-tube (about 3.5 pct). Another method used is based on the shape of a drop of liquid, at rest on an inert refractory plaque, obtained photographically or radiographi-cally. The volume is calculated from the shape, which is sensitive to the surface tension and supporting material, by some intricate empirical relation. The drop contour changes with 90 deg rotation of the support.7 The application of all methods is limited by reaction between liquid metal and the apparatus. The successful stabilization of a mass of liquid metal during levitation melting8 afforded a technique for measuring the density of liquid metals out of contact with solid materials. The technique was developed by using copper as the density of liquid copper has already been studied extensively, thus allowing comparison with the new method. It consists of calculating the volume from the dimensioned profile of the levitated drop obtained by emitted-light photography and careful calibration. The molten egg-shaped drop spins around the magnetic axis of the coil (lined vertically) at a speed which seems to increase with increasing temperature. The method does not involve corrections and the experimental setup allows the use of vacuum or special atmospheres. The maximum operating temperature is limited by excessive evaporation of metal from the droplet. EXPERIMENTAL Levitating System. A stabilizing ring was used in conjunction with a 3-turn levitating coil energized by a 450-kc per sec, 10-kw Toccotron with a high current-low voltage output stabilized to f 1 pet.' APyrex glass tube with a Pyrex Optical flat window inserted through the coil and ring allowed the use of special atmospheres during levitation melting, as shown in Fig. 1. Optical System. Fig. 1 shows the optical arrangement used to photograph the profiles of the drop, parallel and perpendicular to the vertical spinning axis, simultaneously on the same frame of a high-speed 35-mm film. The optical system was adjusted to avoid any distortion of the profiles and to ensure that both profiles are in focus. The length of path from object to objective was about 30 cm, and a magnification factor close to 1 was obtained with the single-lens reflex-camera system. Temperature Measurement and Control. In operation, the specimen temperature was constant to 5 C for a fixed power input to the levitating coil and fixed rate of gas flow through the tube. The temperature was measured by an automatic two-color pyrometer (Coloratio) checked at the melting

Jan 1, 1963

The Ortiz Mountain property is located approximately 40 km (25 miles) southeast of Santa Fe and 13 km (8 miles) from the village of Cerrillos. The property embodies a Spanish mineral grant from which Gold Fields acquired about 2, 200 hectares (900 acres of surface and mineral rights. Following a period of exploration, metallurgical testing and development of a feasibility study in 1974, the decision was made, because of the higher gold price in the fall of 1978, to place the property into production. the gold is confined in a quartzite breccia; it is an unusual occurrence because the gold in this host rock is leachable at minus 19 mm (3/4 in. ). Total ore reserves are estimated at approximately 3.6 million mt (4 million st) averaging 1.89 g per mt (0.055 oz per st) based on a cut-off of 0.7 g (0.02 oz). The ore will be recovered by open pit mining at a stripping ratio of 1. 2:l. Production is scheduled for 13,600 mt (15,000 st) of ore per week or approximately 680,000 mt (750,000 st) per year. Primary crushing of pit-run material is by a 1,070 by 1,015 mm (42 in. by 40 in.) jaw crusher. Crushed ore is conveyed to stockpile and then to a 2.13 m (7 ft) standard crusher with the screened over- size crushed in a 1.5 m (5 ft) tertiary cone crusher. The screen undersize, the final product for leaching, is minus 19 mm (3/4 in. ). A 1, 360 kg (3,000 lb) sample is cut from the crushed ore stream, further crushed in a small jaw crusher and then sampled in two more stages by Vezin samplers to produce a final 13.6 kg (30 lb) sample for assaying. Pebble lime is then added to the ore on the belt as it is sent to the conveyor gantry spanning the leach pads. A tripper on this moving gantry stacks the leach ore without compaction. The entire crushing plant and conveying system is of open-air construction. Leach pads have a total length of 515 m by 60 m (1,700 ft by 200 ft) wide with usable dimensions of 490 m by 58 m (1,600 ft by 190 ft). The directional length slope is 3. 870 with 370 on the width. The pad is constructed of 175 mm (7 in. ) thick asphalt containing a rubberized asphalt membrane. It is divided by a 300 mm (1 ft) high curb into eight segments. Each segment is loaded with 13,600 mt (15,000 st) of ore, which is one week's production. Optimum working height of a pad is considered to be 3. 0 m (10 ft) with a maximum height of 4. 0 m (14 ft).

Jan 1, 1981

By Philip D. Wilson

IT has been my privilege to read the article prepared by R. S. Dean entitled "Production of Alumina from Low-Grade Domestic Materials" which appears on another page of this issue. Dr. Dean should be congratulated on the preparation of such an erudite and scholarly dissertation on bauxite and on the work which the Bureau of Mines has been doing in connection with the development of processes to use low-grade domestic materials.

Jan 1, 1943

By Ed Van Eeckhout

As part of a U.S. Bureau of Mines-sponsored project on the utilization of "stiff" backfill to minimize potential rock burst hazards, a finite element study was undertaken to predict stresses and displacements around a stope mined up from the 5400 level of the Sunshine mine, Kellogg, Idaho. This stope was to be backfilled using a high-modulus fill. In preparation for that configuration, certain instrumentation was installed near the 5400 level to monitor stress changes. Due to untenable economics, only 2 cuts of the stope were ever made. This paper presents the results of the instrument readings taken during the first cut and compares them with the numerical predictions, as well as presents the modeling results of closure and fill stresses in the stope if it had been mined.

Jan 1, 1984

By E. W. Parker

Anthracite, as sent to market, comes under three general terms of description: characteristics, source and size. Anthracite is generally classified as white ash, red ash, or Lykens Valley. The white ash coals are sometimes further described as "hard" or "free-burning." Lehigh white ash would come under the former description and Shamokin white ash under the latter. As a rule, it may be said that the nearer the origin of the coal to the western extremity of the anthracite region, the softer and more free-burning it is. Indeed, for many years the coal from Trevorton, at the western tip of the Middle Western field, was classified as "semianthracite" in the shipment reports. Lykens Valley coal is always a red ash coal, with a higher volatile content than the general run of anthracite, and consequently free-burning. The name does not exclusively indicate the neighborhood in which the coal is dug, but rather refers to the beds from which it is obtained. These beds lie, not above the Pottsville conglomerate, as is the rule, but encased in it. The extreme eastern limit of the Lykens Valley beds would seem to be about Tremont, in Schuylkill County, and the Natalie mine, near Mount Carmel. There are, of course, traces of these beds farther to the east, but they do not seem to be workable. There are as many as six of the Lykens Valley measures found in the conglomerate at some points, but to a large extent they are unworkable. Whether this coal is obtained in the Lykens Valley proper, where the beds were first identified, or from the Shamokin Valley, it is always Lykens Valley coal, and it has long been considered a premium coal, especially desirable for domestic use, particularly when a quick, hot kitchen fire is desired. Coals are, of course, frequently marketed under special names—Jeddo, Scranton, Kingston, Old Company Lehigh, Famous Reading, Lacka-wanna, etc.—which, of course, have the trade significance which their producers and vendors have built up. General Description of the Various Coals, with Name of Seam and Producing District This is partly covered in the paragraphs above. Lykens Valley coal is produced from one or another of the six Lykens Valley beds lying within

Jan 1, 1930

By J. B. Clark, A. J. McEvily, R. L. Snyder

The nonuniform distribution of precipitate particles has been recognized as a leading factor contributing to the relatively low fatigue resistance of aluminum alloys. The structure of many of these alloys is characterized by narrow precipitate-free zones adjacent to the grain boundaries. Alloys with such zones exhibit a tendency for brittle inter crystalline fracture. The interrelation between this type of structure and mechanical properties was investigated in an Al-10 wt pct Mg alloy. It was found that deformation during fatigue occurs preferentially along these zones and cracks initiate there. In Al-10wt pct Mg, the zones were found to be supersaturated even after extensive general precipitation and are due to the absence of proper precipitate nuclei in the region near the grain boundaries. Cold working the alloy prior to aging improves the mechanical properties by inducing precipitation within the zones and also by jogging of grain boundaries. The mode of fracture is changed from brittle inter crystalline to more ductile trans granular fracture. THE process of fatigue is highly structure sensitive, with the strength of the whole often dependent upon some localized discontinuity, either geometrical or metallurgical in nature. Much has been learned about the role of geometrical discontinuities, e.g., notches, in fatigue, but with the exception of the effects of inclusions or the shapes of carbides, relatively little is known about the specific effects of discontinuities in metallurgical structure such as nonuniform precipitation. In most age-hardening aluminum alloys, metallo-graphic studies have shown that the extent of precipitation adjacent to grain boundaries is much less than that which occurs in the interior of the grains. The width of these almost precipitate-free regions, which are sometimes called denuded zones, and the extent of solute depletion within them, are dependent upon the particular alloy and its aging treatment. It has been observed1 that these zones are relatively soft with the result that plastic deformation takes place preferentially within them. It has also been shown 2-4 that there exists a tendency for intercrys- talline cracking in fatigue when such zones are present. It is of interest to note that Broom et al.2,3 were able to reduce the incidence of this type of failure in an A1-4 wt pct Cu alloy by stretching the material 10 pct prior to aging. In the present study, the effects of precipitate-free regions on the fatigue properties of an A1-10 wt pct Mg alloy were studied in detail, and the effects of deformation prior to aging on the nature of the precipitation process as well as on fatigue properties were also investigated. MATERIAL AND PROCESSING An A1-10 wt pct Mg alloy was selected for this study, because it was known that well-defined precipitate-free regions along the grain boundaries are readily obtained in this alloy after aging at 200oC.5 The starting materials were 99.998 pct A1 and singly sublimed magnesium of about 99.9 pct purity. The aluminum was induction melted in a graphite crucible, and then the magnesium addition was immersed until dissolved. Chlorine gas was then bubbled through the molten alloy for 4 min to degas the melt, after which the melt was cast at a pouring temperature of 730" to 760°C into a cold, graphite-coated, tapered steel mold. Since A1-Mg alloys are difficult to homogenize,5 special care was taken to obtain a uniform composition. Two-in. cubes were cut from the ingot and heated at 446°C for 30 min. These cubes were then hot forged approximately 35 pct in each of the three cube directions and homogenized for 16 hr at 446°C. Sheet specimens were then obtained by pressing 40 pct and rolling 35 pct per pass with reheating between reduction steps to a final thickness of approximately 0.10 in. The sheet was then solution treated for 16 hr at 446°C and water quenched. The age hardening behavior of this material at 200°C was then determined, and the results are shown in Fig. 1. The age hardening of this alloy when subjected to cold work prior to aging is also shown in this figure. Preliminary work indicated that extensive deformation after quenching was required to affect drastically the precipitate-free regions in this alloy, and a rolling reduction of 50 pct was chosen. For purposes of comparison the following three conditions were studied: a) Solution treated, quenched, and aged 20 hr at 200°C

Jan 1, 1963

By Frank Firmstone

When in charge of the Glen don Iron Works, the importance of good methods of filling was forcibly brought to my attention, and it occurred to me that the first step toward the discovery of the best plans was the accumulation of exact information as to the distribution actually effected by various chargers; also, that something could be done in this direction by careful measurements in the furnace, to be afterwards recorded for comparison on drawings. The figures shown herewith have been prepared from such measurements, and nearly all of them refer to Glendon, where the fuel used was anthracite and the ore-mixture about threequarters of New Jersey magnetic ores and one-quarter of brown-ores from the vicinity of the works. Every occasion furnished by the blowing-in of furnaces was utilized, but the data accumulated rather slowly in this way; and, opportunity oEering to make special trials at no great expense, the figures from 2 to 7 were thus obtained. The trials were made by dumping a hopperful (6 barrows) of material at once into the furnace, and, when all the fuel of a round (12 barrows) had been put in, the profile of the upper surface was obtained by stretching a steel tape across the top on a diameter and at a known height. By measuring down from this with a graduated rod, the profile was easily obtained with sufficient accuracy, especial pains being taken to get correctly the crests of the ridges and the bottoms of the hollows, as many intermediate points being included as seemed necessary. This was repeated on another diameter when there was occasion. The same course was followed for the limestone and ore.

Jan 1, 1899

By G. R. M. Del Giudice

A survey of the flotation literature of the past 10 years indicates an increasing use of the microscope as a tool for investigation. Thus, the metallurgical microscope has been used by Tucker and Head;' Taggart, Taylor and Ince;2 Ince,3 and del Giudice4 to examine mineral surfaces that had been subjected to the action of various flotation reagents and to the action of slime pulps. It has also been used by Gaudin, Groh and Henderson;5 Martin;6 Morrow and Griswold;7 and others to examine bakelite briquets of mill products. The microscope with transmitted light, both with bright-field and dark-field illuminations, has been used by Taggart, Taylor and Knoll8 and by Ince9 to observe Brownian motrement and flocculation in flotation pulps. The use of the microscope at low-power magnifications with incident illumination for the examination of mill products has been known for years.10 Finally, del Giudice11 has used a relatively new type of illumination, the Ultropak, for the examinntion of slime-coatings.

Jan 1, 1935

By H. E. Cook

The Ising model for the internal energy of a binary alloy has been used to obtain a general equation for the critical resolved shear stress of partially ordered crystals. The equation expresses the stress in terms of the Warren "alphas " and can be used to estimate the variation in strength with order without the assumption, present in the original formulation of this problem in terms of domain size, that order is complete within each domain and that the domains are of ungorm size and shape. In addition, it is the general equation, according to the Ising model, for strengthening by short-range order. Two applications of the equation are considered: One is an estimate of the variation in strength of CkAu with long-range order. The other is an estimate of the variation in strength of FeCo with quench temperature. Reasonable agreement is found with the variations reported in the literature. When the internal energy of an alloy crystal depends upon the distribution of solute, the strength of the crystal will also depend upon it because a portion of the applied stress for plastic deformation will be: where V is the volume of the crystal and E(E) is the energy change associated with the solute redistribution caused by the plastic strain, E. We expect T to equal zero for a crystal having a random arrangement of solute because the arrangement would remain random after plastic deformation. Likewise, we expect it to equal zero when the crystal is perfectly ordered because the motion of paired dislocations found in such crystals does not disrupt order. However, when short-range order exists or when long-range order is incomplete, plastic deformation will decrease the amount of order and additional work, proportional to the ordering energy, will be expended. Fisher' estimated T for crystals having short-range order by assuming an interaction energy between neighboring atoms and estimating the change in the number of unlike neighbors as a dislocation moved through the crystal. (His analysis was limited and several workers2"6 have since given more complete ones.) Fisher minimized the importance of a strengthening mechanism of this type for paired dislocations in a structure having long-range order. ~ottrell,' however, pointed out that T could be appreciable for ordered crystals having antiphase domains. He attributed the strengthening to the increase in surface energy of the domains as they were cut by paired dislocations. Ardley,' in his test of Cottrell's theory, found that r for Cu3Au crystals obeyed the equation: for 1 > t where 1 is the domain size, t is the domain wall thickness, and y is the surface energy of an antiphase boundary. His experiments represent the classic confirmation of the strengthening mechanism proposed by Cottrell. However, the assumptions involved in using Cottrell's theory are valid only for large domain size in CU~AU,~"~ i.e., when Eq. [2] reduces to: For small domains, ~linn~ has questioned Ardley's assumption that order was complete, and, indeed, Stoloff and ~avies" fpnd it incomplete until a size of approximately lOOA was reached. Even when the order within a domain is complete, it is not obvious how one determines the appropriate value for I in a structure where domains vary in size and are irregularly shaped. The purpose of this paper is to estimate T without restrictions upon the degree of order and domain shape. Our major assumption will be the use of a generalization of the model proposed by Bethe" (the Ising model) for the internal energy. This will in fact allow us to combine the theories for strengthening by short-range order and by antiphase domains into a single, general formalism. We will use the results to estimate the variation in strength of Cu3Au crystals with long-range order8 and the variation in flow stress of FeCo crystals with quench temperature.12'13 INTERNAL ENERGY For simplicity, we restrict our considerations to those binary solid solutions which can be described as an arrangement of atoms on a Bravais lattice. An atom site will be indexed by three numbers (PI, pz, p3) determined by the vector: from the origin fixed at atom (0, 0, 0) to the atom site where a', an, and a, are the lattice translation vectors. We write: For the energy of the crystal where pi(p) is the probability (either zero or one) of finding an atom of type i (i = 1, 2) at site (p), which is shorthand for (pl, pz, p3) and pj(p + r) is that for an atom of type j (j = 1, 2) at the site (p + r), which is shorthand for (pl + rl, The coupling parameter, resents the energy associated with the pair Pi(p), Pj(p + r). The crystal is assumed large enough so that surface effects can be neglected; therefore, trans-lational and inversion symmetry require the coupling parameters to obey the relations

Jan 1, 1969

By W. C. Hayes

The site selected for the United States prototype pumped storage project of Union Electric CO. was Proffit Mountain, five miles from Taum Sauk, the highest point in Missouri. Factors influencing final location were: high local relief; satisfactory rock type and structure; and an economic location in respect to existing transmission systems. The upper reservoir was constructed by excavating rhyolite porphyry from the crest of Proffit Mountain and constructing a rock fill dike encircling the area to form a 4350-acre foot reservoir. A 6564-ft tunnel connects the upper reservoir with the generating and pumping facilities. A concrete gravity dam on the East Fork of the Black River forms the 6350-acre foot lower reservoir. Precambrian rhyolite porphyry forms the crest of Proffit Mountain and the floor of the upper reservoir. The tunnel was excavated in rhyolite prophpy, granite porphyry, dolomite, shales and conglomerate. Abutments and the foundation of the gravity dam are in rhyolite porphyry, and much of the valley floor of the lower reservoir is underlain by dolomite and shale. Core drilling provided data on soundness of rock type, structure, depth of weathered zone and potential water loss in the fractured igneous rocks. After a six-year study of pumped storage and cost comparison with alternate stream generating units, the Taum Sauk pumped storage project was authorized by Union Electric Co. on Dec. 11, 1959.' The site selected is located in the St. Francois Mountains of southeast Missouri approximately 90 miles south of St. Louis (Fig. 1). The lower reservoir was provided by damming the East Fork of the Black River, a small tributary of the Black River with a minimum flow of about 1 sec ft. Construction of the upper reservoir was effected by quarrying the crest of Proffit Mountain - five miles from Taum Sauk Mountain, the highest point in Missouri — to provide material for a rock fill dike surrounding the quarried area. This provided a 55-acre mountain top lake with a water depth of 92 ft (Fig. 2). A vertical shaft and tunnel connect the upper and lower reservoirs through the two reversible pump-turbine motor-generator units operating under 800 ft of hydraulic head (Fig. 3). The output rating of the plant is 350,000 kw with daytime generation of about 2.2 million kw-hr under normal use. Night pumping will replenish water to the upper reservoir in about 91/2 hours3. The automatic operation is remotely controlled from the Osage plant and from the dispatchers office in St. Louis. GENERAL GEOLOGY Mountains of the St. Francois area consist of Precambrian granites, granite porphyries, extrusive fel-sites and basic dikes. Basal conglomerates overlain by Upper Cambrian Bonneterre dolomites and shales onlap the exhumed Precambrian knobs and hills and are exposed in the narrow valleys. Cambrian and Ordovician residuum as much as 200 ft thick is present on the slopes of many hills. Proffit Mountain consists of rhyolite porphyry and granite porphyry. All excavation for the upper reservoir was in rhyolite porphyry, and the same rock is present under the Bonneterre at the plant site and under alluvium at the lower reservoir dam site. The region has been dissected to the stage of early maturity with only small upland flats remaining. Considerable local relief (a requisite for the project) approaches 1000 ft. Streams flowing across the Precambrian ridges have formed restricted narrows, termed shut-ins. A shut-in approximately two miles downstream from the plant site provides an excellent site for the lower reservoir dam. TEST BORINGS Preliminary to final approval of the project, 12 test borings were made to determine subsurface geologic conditions (Fig. 2). Drill hole No. 12 at the lower reservoir dam site showed 20 ft of alluvium over solid rhyolite porphyry. Drill holes No. 1, 2 and 3 were drilled in the tail race area to depths of 66 ft, 75 ft and 95 ft respectively, and all bottomed in Bonneterre. Drill hole No. 4 at the plant site provided NX core to a total depth of 98 ft in Bonneterre. Drill

Jan 1, 1965

By H. E. Wilborg

This chapter deals with those sands employed by the foundries for the manufacture of cores and molds used in the casting of such common metals as steel, gray iron, ductile iron, aluminum-based alloys, and copper-based alloys. Most metal is cast in "green sand" molds in which the sand mixture, consisting primarily of silica, clay, and water, forms a plastic material. This plastic material is rammed around a pattern in a split box called a flask, then the box is separated, the pattern is withdrawn, and the metal poured. These green sand molds are broken apart when the metal has solidified. The sand is then remixed and a new mold made for the next casting. To a lesser extent silica sand is mixed with resins or oils and, after forming, the mixture is hardened either by heat or chemical reaction. In any case, the foundry mold or core is used just once before being broken up and remixed for manufacturing another core or mold. By far the greatest consumption in the foundry is of those types of sand high in silica, low in clay (under 0.5%) and occurring in numerous locations thoughout the United States.

Jan 1, 1975