Search Documents

By H. R. Page, A. E. Jr Lee

A. E. LEE, JR. (author)—In addition to the paper we should like to make a few remarks. First, the seriousness of bending of the clay retort cannot be overemphasized. Not only did bending limit the length of the vessel, but it permitted corrosive fluid slags to concentrate in the belly of the retort and thus increased the possibility of boring. Bending also practically prohibited the use of cleanout machines and increased the danger of excessive fume losses by allowing furnace gases to escape around the top of the retort mouth. It will be noted that the Blackwell pottery practice places considerable emphasis on careful drying of retorts. Perhaps it is another smelter superstition, but traditionally the aging of retorts beyond a reasonable drying period has been considered important to long life. We are unable to give a good explanation of why aging should improve retorts. During the past fall in an attempt to prove a theory that the combined water in the clay decreased during aging, about 50 samples of wet retort collars were placed in a dry room when it was closed. Loss of weight, combined water and free moisture were measured each week over the 100 day drying period. The affinity of the dried retort for moisture makes difficult the accurate measurement of free water; however, there was a clearly defined free moisture change from about 12.5 pct when freshly made to about 2 pet at the end of 18 days, then a gradual loss to about 0.25 pet at 70 days and an apparent equilibrium near this figure through the 100th day. There was no appreciable change in the combined water. The change in weight of the average sample was, however, rather unusual, there being consistently a loss of weight throughout the entire 100 days. From the 63rd day on this leveled off to about 0.03 pet per week. These were small samples and certainly should have dried

Jan 1, 1950

By Norman Weiss

The need for more efficient utilization of labor in the metal-mining industry has been the subject of several recent editorials in the mining press, and one attractive possibility for such improvement lies in the designing of future milling plants particularly with economy of manpower in mind. We are accustomed to think of mill design as the selection and coordinated arrangement of process equipment, but if labor is to be efficiently utilized it must be given early consideration in planning the new mill. There are three good reasons for economizing in labor: (I) to reduce costs, not only in the form of wages but also in housing, hospital, welfare, and other obligations that a company accepts when a new man is added to the payroll; (2) to prepare for recurrent periods of manpower shortage, during which a well-designed plant can manage to get along with skeleton crews; (3) because a milling plant that must depend upon an inordinately large labor force for its operation and maintenance is certain to be inefficient in other respects, for many of the shortcomings in design that make necessary the excessive use of labor are generally not corrected merely by having too many men. A simple example of this is a poorly designed ore-feeding system : if this is inadequate to the extent that one man must be constantly unclogging feed chutes, it may help the situation to put two men or three at this task instead of one, but the feed rate will still be inconstant. First of the factors that affect labor saving is the location of the mill. This is often determined by transportation costs alone, and as a result the mill may be placed close to the mine regardless of the nature of the terrain. The designer must then adapt his layout to the conditions, favorable or not. This happens often at small properties, where capital investment may seem more important than operating expense. In most instances, however, a mill site carefully selected for the advantages it gives the designer in laying out the plant is the most economical in the long run, even if it involves a slight increase in cost of ore haulage. Given some freedom of choice, the design engineer may be able to find just the piece of ground that provides the proper gradient for the needs of the flowsheet, permits installation of essential yards and trackage, and perhaps supplies an excellent site for a tailing dam. Further justification for having placed the mill not too close to the mine sometimes emerges only years later as an opportunity to treat ores from other properties. When it is known from the beginning that the new mill will serve a number of scattered mines, a free choice of mill site is naturally stimulated. The most important single factor in limiting the labor requirements of a mill is its materials-handling system for bring-

Jan 1, 1947

By Norman Weiss

The need for more efficient utilization of labor in the metal-mining industry has been the subject of several recent editorials in the mining press, and one attractive possibility for such improvement lies in the designing of future milling plants particularly with economy of manpower in mind. We are accustomed to think of mill design as the selection and coordinated arrangement of process equipment, but if labor is to be efficiently utilized it must be given early consideration in planning the new mill. There are three good reasons for economizing in labor: (I) to reduce costs, not only in the form of wages but also in housing, hospital, welfare, and other obligations that a company accepts when a new man is added to the payroll; (2) to prepare for recurrent periods of manpower shortage, during which a well-designed plant can manage to get along with skeleton crews; (3) because a milling plant that must depend upon an inordinately large labor force for its operation and maintenance is certain to be inefficient in other respects, for many of the shortcomings in design that make necessary the excessive use of labor are generally not corrected merely by having too many men. A simple example of this is a poorly designed ore-feeding system : if this is inadequate to the extent that one man must be constantly unclogging feed chutes, it may help the situation to put two men or three at this task instead of one, but the feed rate will still be inconstant. First of the factors that affect labor saving is the location of the mill. This is often determined by transportation costs alone, and as a result the mill may be placed close to the mine regardless of the nature of the terrain. The designer must then adapt his layout to the conditions, favorable or not. This happens often at small properties, where capital investment may seem more important than operating expense. In most instances, however, a mill site carefully selected for the advantages it gives the designer in laying out the plant is the most economical in the long run, even if it involves a slight increase in cost of ore haulage. Given some freedom of choice, the design engineer may be able to find just the piece of ground that provides the proper gradient for the needs of the flowsheet, permits installation of essential yards and trackage, and perhaps supplies an excellent site for a tailing dam. Further justification for having placed the mill not too close to the mine sometimes emerges only years later as an opportunity to treat ores from other properties. When it is known from the beginning that the new mill will serve a number of scattered mines, a free choice of mill site is naturally stimulated. The most important single factor in limiting the labor requirements of a mill is its materials-handling system for bring-

Jan 1, 1947

By Paul T. Allsman

Recently the U.S. Bureau of Mines completed organizational changes that, for the first time since the beginning of World War 11,. re-emphasize mining research as an important part of its responsibilities. A progress report follows on the Bureau's improved program for mining research. During World War II the Bureau's mining research lapsed in favor of short-range, more urgent activities. Since the end of the war mining has grad- ually returned to an economy where reduced costs and increased efficiency are essential to a vigorous industry, and demand for improvement through expanded research is again pre-eminent. In recognizing this situation, the Bureau is again emphasizing mining technology and has reinstituted some of its earlier mining research activities. Recent research, however, follows a more scientific approach in solving mining problems because new technology, particularly new instrumentation, has developed rapidly during the past decade.

Jan 7, 1960

By B. F. Decker, D. Harker

The recrystallization reaction in OFHC and spectroscopically pure copper has been followed by X ray diffraction determinations of the amount of material with the cold-worked and recrystallized textures in specimens which had been given various heat treatments. The heats of activation for recrystallization are found to be: 29.9 kcal per rnol for OFHC copper and 22.4 kcal per rnol for spectroscopic copper. A reliable and speedy method for measuring the amount of recrystallized material in a piece of rolled metal, together with a new scheme for low temperature heat treatment, have made possible a determination of the activation energy for recrystallization in rolled copper. This method for studying recrystallization rates is different from others reported in the literature.' Oxygen free, high conductivity copper—OFHC copper—of purity 99.98 pct gave an activation energy for recrystallization of 29.9 kcal per mol with recrystallization data taken in the temperature range 208-245°C. Copper of purity 99.999 pct from the American Smelting & Refining Co. gave an activation energy for recrystallization of 22.4 kcal per mol with recrystallization data taken in the temperature range 43-135°C. The great change in activation energy for recrystallization as the small amount of impurity in the metal is decreased suggests that the motion of grain boundaries is conditioned by the impurities which must be concentrated in them. Thus the OFHC copper recrystallizes with an activation energy of the order of magnitude to be expected for the diffusion of the kind of impurities likely to be present. The high purity copper, on the other hand, recrystallizes with a much lower activation energy, in accord with the notion that the grain boundaries need not wait for the impurities to diffuse with them. Copper when strongly cold-rolled has a well-defined crystallite texture which can be described by saying that the [111] direction of the face- centered cubic crystals is aligned approximately in the cross-rolling direction and that faces of the form {110} lie approximately in the rolling plane. When such rolled copper is completely annealed the crystallite texture is quite different: the [loo] direction is in the cross-rolling direction and faces of the form (100) are in the rolling plane. At intermediate stages of annealing, the copper contains both textures. If a Geiger counter X ray diffraction spectrometer is set up so as to measure the intensity of the (200) Bragg reflection from the rolled surface of a piece of copper strip, this intensity increases from a very small value in the cold-worked state to a maximum as the specimen is annealed. The same would be true for (200) reflections from planes normal to the rolling or cross-rolling directions. In view of this fact, the amount of material in the copper which has recrystallized can be measured by comparing the intensities of one of these reflections just mentioned with the intensity from a similar specimen after complete annealing. In much the same way the intensity of (111) reflections from planes normal to the cross-rolling direction could be used to measure the amount of unrecrystallized material in the specimen. In the work to be described here the amounts of recrystallized and unrecrystallized material in partly annealed rolled copper specimens were determined in this way. Experimental Procedure Samples of oxygen free high conductivity (OFHC) copper, cold-rolled 99.7 pct to 0.002 in. thickness, were subjected to heat treatments for various chosen times at four different temperatures, and high purity copper samples, cold-rolled 98.0 pct to 0.0015 in. thickness, at six different temperatures. Each sample, after treatment, was placed in an orientation sample holder for use with a Geiger counter X ray spectrometer and a reading was taken of the intensity of the (200) reflection from planes perpendicular to

Jan 1, 1951

By Frank F. Poland

TEE purpose of this paper-is to describe a new process for the refining of secondary copper-base metals and a specially designed high-temperature electric-resistor furnace used in the process for the distillation of zinc from these metals. The process was used for the conversion of nickel silver to cupronickel and to recover the zinc content in metallic form. It also proved applicable and economical for the treatment of scrap brass for separating and reclaiming the copper and zinc. The relatively large furnace developed for the distillation of zinc is described in detail, for it made economically possible the direct recovery of metallic zinc from scrap brass, which is a new step in the processing of such material. Considerable interest has been shown in the utilization of the distillation furnace for other metallurgical processes, where it is of advantage to operate in a controlled neutral or reducing atmosphere, or to avoid having the processed metal in contact with refractories other than carbon, or to operate at temperatures between 3000 and 4000°F. PURPOSE OF DEVELOPMENT It was recognized early in the war effort that nickel would become a critical metal, therefore all nickel stock and alloys containing relatively high percentages of nickel were frozen immediately. Among these alloys were considerable quantities of various grades of nickel silver, an alloy containing copper, nickel, zinc, and in some grades lead, also minor amounts of iron, manganese and other constituents. At the time there was no existing plant or process to eliminate the zinc, lead, and minor constituents so as to convert this metal to cupronickel, one of the important alloys needed by the U. S. Navy for condenser parts. Therefore the Bureau of Industrial Conservation of the War Production Board requested the executives of the leading nonferrous metal companies to have their metallurgical staffs study the problem of converting this metal to cupronickel conforming to U. S. Navy Specification 44T40. The composition specified therein is as follows: nickel, 29 to 32 per cent; zinc, 1.00; iron, 0.00 to 0.60; lead, 0.05; tin, 1.20; manganese, 0.00 to 1.00; total of other elements (maximum), 0.50; copper, remainder. The problem in converting these alloys to cupronickel was the elimination of zinc, lead, iron, manganese, and other elements without appreciable loss of nickel to slags or other by-products. Revere Copper and Brass Incorporated, through its Research and Development Department, undertook to solve this problem. A Government-owned plant was built at Rome, N. Y., and there the con- version was successfully made.

Jan 1, 1946

A discussion at a joint meeting of the New York Section of the American Electrochemical Society and the American Institute of Mining Engineers, Nov. 20, 1913. Chairman Lawrence Addicks:-Our program this evening represents an attempt to set before you the present situation and outlook in the metallurgy of zinc. It is a time-honored custom to throw bricks at the zinc man. The accusation is that he has borrowed a lime kiln and a gas retort and part of a sulphuric acid plant, hitched them together, and spent the last 50 years in regarding with holy veneration the reactions which take place in that retort. The copper man, who thinks of zinc as something with which copper is adulterated to make brass, and the iron man, who regards it as a sort of paint for corrugated sheets, and the lead man, whose opinion as to zinc is not fit for publication, have long felt that, when two or three of the minor details of their respective metallurgies were put in order, they would take a few clays and fix up zinc on a modern basis. But somehow there still seem to be some unsolved problems at home, and while we are waiting it seems only fair that the case for the defense should be adequately presented. There is probably no man in this country to-clay better able to do this than Mr. George C. Stone, of the New Jersey Zinc Co., on whom I have pleasure in calling to talk to us on "Progress in the Metallurgy of Zinc." George C. Stone:-It is frequently stated that there has been no change in the metallurgy of zinc since the first Belgian furnaces were built in the early part of the last century. It is true there have been no such spectacular and radical changes as were worked in the metallurgy of copper and iron by the introduction of converters; but, in the essentials, I believe the progress in zinc metallurgy has been as great as in that of the other common metals. The main reason that there have not been revolutionary changes is that the chemistry of zinc differs radically from that of the other metals and these differences control the type of apparatus that can be used. The differences are: 1. The temperature at which zinc is reduced by carbon is much above the volatilizing point of the metal and it is therefore always produced as a vapor.

Jan 1, 1914

By S. Arthur Krom

(New York Meeting, February, 1912.) THE James diagonal-plane slimer is specially adapted to handle the finest slimes, but it will also handle sands as coarse as 40-mesh. The saving efficiency of this machine is due to the original construction of the deck, and to the rapid reciprocating movement imparted to it by the head-motion. The deck consists of a plurality of connected planes, having a certain fixed ratio of inclination one to another. These planes intersect each other diagonally to the stroke-line of the table and are arranged so as to give the pulp on the table a double treatment. This double concentration performed by the diagonal-plane deck produces cleaner concentrates and tailings than those obtained by the operation of two separate machines. The action of the diagonal planes settles, combines, and holds all the concentrates in one compact mass, sharply defined from the gangue, and easily cut away without loss. Many slime-concentrating machines distribute the feed-pulp for a distance of 4 or 5 ft. only, and upon a very limited settling-surface. This results in a thick, heavy deposit, from which it is impossible to stratify the values and wash, away the gangue, the resulting products being dirty concentrates, and tailings carrying high values. The diagonal-plane slimer distributes the feed-pulp for a distance of 10 ft., and upon a settling-surface having an area of 40 sq. ft.; in other words, it spreads the pulp thinly on the table, which allows the metallic values to settle through the gangue quickly, forming a bottom stratum from which the thinly-distributed overlying stratum. of gangue is easily brushed away by the feed-water without disturbing the underlying concentrates. Referring to Fig. 1, plane A is the main settling-section, of the table. The feed pulp flows gently down this plane and is

Jun 1, 1912

PRESIDENT AND DIRECTOR R. C. ALLEN . CLEVELAND, OHIO PAST PRESIDENTS AND DIRECTORS H. A. BUEHLER ROLLA, Mo. JOHN M. LOVEJOY NEW YORK, N. Y. VICE-PRESIDENT, TREASURER AND DIRECTOR KARL EILERS NEW YORK, N. Y. VICE-PRESIDENTS AND DIRECTORS HENRY KRUMB NEW YORK, N. Y. PAUL D. MERICA NEW YORK, N. Y. H. G. MOULTON NEW YORK, N. Y. HARVEY S. MUDD Los ANGELES, CALIF. WILFRED SYKES CHICAGO, ILL..

Jan 1, 1937

PRESIDENT AND DIRECTOR JOHN M LOVEJOY NEW YORK, N. Y PAST PRESIDENTS AND DIRECTORS HOWARD N EAVENSON PITTSBURGH, PA HENRY A BUEHLER ROLLA, MO. VICE PRESIDENT, TREASURER AND DIRECTOR KARL EILERS NEW YORK, N Y VICE PRESIDENTS AND DIRECTORS LOUIS S CATES NEW YORK N Y PAUL D MERICA NEW YORK, N Y WILFRED SYKES CHICAGO, ILL R C ALLEN CLEVELAND, OHIO HENRY KRUMB NEW YORK, N Y

Jan 1, 1937

PRESIDENT AND DIRECTOR JOHN M. LOVEJOY NEW YORK, N. Y. PAST PRESIDENTS AND DIRECTORS HOWARD N. EAVENSON PITTSBURGH, PA. HENRY A. BUEHLER ROLLA, Mo. VICE-PRESIDENT, TREASURER AND DIRECTOR KARL EILERS NEW YORK, N. Y. VICE-PRESIDENTS AND DIRECTORS LOUIS S. CATES NEW YORK, N. Y. PAUL D. MERICA NEW YORK, N. Y. WILFRED SYKES CHICAGO, ILL. R. C. ALLEN CLEVELAND; OHIO HENRY KRUMB NEW YORK, N. Y.

Jan 1, 1936

By Frederick Laist

I AM APPRECIATIVE of the honor you have done me in electing me to membership in your Society. I value the contacts with men of imagination and ideals which this implies. I am grateful for the recognition of such small contributions as I may have made, or helped to make, to the vast fund of scientific and engineering knowledge. We like to think, as we grow older, that our lives have not been purely parasitical, and that through our efforts some forward step, however small, has been taken toward improving conditions under which we live and do our work. In these days of industrial depression, we hear much criticism of our "machine age." Modern engineering, mass production, the complexity of our lives, all come in for some share of blame. The farmer is said to have been spoiled by the tractor and the gang plow, the factory worker has become a slave of the assembly conveyor, the scientific worker is no longer free but has sacrificed much of his individuality to the research organization of which he is a part. We wonder whether our work as engineers has been worth while and whether our striving after more efficient ways of doing things has been a curse to mankind rather than the boon we thought we were conferring.

Jan 1, 1932

By S. H. Shepard

During the past year, a number of significant events have occurred in the nuclear industry. These include a surge in nuclear power plant orders, delays in nu- clear plant licensing and construction, increased environmental concern and the new Atomic Energy Commission nuclear fuel policy. These events, particularly the AEC stockpile release policy, have lead us to take this opportunity to update National Nuclear Corp.'s (NNC) appraisal of the outlook for the U.S. uranium industry.

Jan 10, 1972

By C. R. Boyd

In 1874 I received an appointment in the corps organized by Col. William P. Craighill, U. S. Engineers, to survey the New or Upper Kanawha river for the purpose of ascertaining the practicability and

Jan 1, 1895

Jan 1, 1895

THE Bergbüchlein and Probierbüchlein occupy a unique position in the literature of mining and metallurgy, for, they are the first printed books on any aspect of the two related professions. The first printed book on any subject has an allure that may not be entirely warranted by the strict historical significance of its contents. Among the books of the first century of printing there are very few that contain information that was new at the time of publication. Much' of what they recorded had been previously circulated in manuscript form. Printed books are nevertheless of great value because they mark the time when the author's words, free from errors-or at least with the same errors-became available to large numbers, of readers, who thus could easily and cheaply acquire a common background for their future work. Moreover, though there is occasionally some doubt as to the exact year of publication'(as in the case of the present works), it is generally easier to date a printed work than a manuscript, and thus to provide a fixed coördinate in history. The Bergbüchlein, "The Little Book on Ores," is the first printed work in the field of mining. It is an introduction to mining geology, which means that it was not addressed to the practicing expert but was intended to rouse the interest of beginners in the various aspects of a future vocation. It touches on the theories of the generation of ores, introduces and defines some of the most frequently encountered technical terms of the profession, and indicates what knowledge and tools are required for successful prospecting and mining. It also describes the ores of the seven most important metals. For those parts that deal with theory the author accepted uncritically the traditional teachings of the alchemists and the astrologers; his hints on where to find promising ores are based partly on superstition; but, there is enough factual,

Jan 1, 1949

Following the suggestion of Engineering Council and at the direction of, the President, representatives from each of the Federal Government bureaus interested in map-making were called into a conference for the purpose of coordinating all of the Government's map-making activities. This conference has now reported back to the President the results of its findings, which indicate that Engineering Council's recommendation in this matter was well founded. While the conference report states that its members were of the opinion that little duplication of effort existed, it recommends the formation of a permanent Board of Surveys and Maps. An extended review of the map-making activities, which is given as an appendix to the report, indicates that this recommendation is a logical step. The conference recommendations concerning this Board of Surveys and Maps are as follows: (1) the Board is to he com-posed of representatives of mapping bureaus to be assisted by outside engineering organizations, which have been named above; (2) the estab-lishment of an information office in one of the Government bureaus, preferably the Geological Survey, which is to be under the supervision of the Board and is to be a mapping information clearing house for the Government and outside engineering organizations; (3) copyright laws are to be so changed that copies of all. maps made in the United States and with Governmental authority, will go to the central information office; (4) the Government departments are to receive orders to cooperate, with the Board; (5) future topographic maps of all kinds are to conform with specifications for the standard topographic map; (6) the U. S. Coast and Geodetic Survey to have supervision of final adjustment of all important control data under specifications approved by Board of Surveys and Maps; (7) surveys in the form of maps and publications are to be issued as soon as possible after field work has been completed; (8) program of the Interdepartmental Committee on Aerial Surveying was approved. Outside technical and scientific organizations that are called in for consultation are to operate in an advisory capacity only, responsibility for action on Governmental work is. to rest solely with the Governmental agencies.

Jan 12, 1919

THE following employment items are mode available to AIME members on a nonprofit basis by the Engineering Societies Personnel Service, Inc., operating in cooperation with the Four Founder Societies. Local offices of, the Personnel Service are at 8 W. 40th St., New York 18; 100 Farnsworth Ave., Detroit; 57 Post St., San Francisco; 84 E. Randolph St., Chicago 1. Applicants should address all mail to the proper key numbers in care of the New York office and include 6c in stamps for forwarding and returning application. The applicant agrees, if placed in a position by means of the Service, to pay the placement fee listed by the Service. AIME members may secure a weekly bulletin of positions available for $3.50 a quarter, $12 a year. POSITIONS OPEN Mining Engineer with some engineering training, capable of doing mapping, surveying, exploration, geology and transit work. Location, New York State. Y7333. Mineral Dressing Engineer, B.S. Mining or Chemical Engineering, age to 35. Must have knowledge of flotation. Duties will be in applied research and field evaluation of cationic and anionic flotation agents. Salary, $3500 to $7000 depending on experience. Location, Chicago. R-8971. Geological Draftsman, 25 to 30, with some experience in working with a geologist. Salary, $5100 a year. Location, New York, N. Y. Y7153.

Jan 1, 1952

By T. Egleston

In the year 1881 I presented to the Institute two papers containing the resnlts of researches on gold, in which I endeavored to make plain some of the causes of the losses in the working of gold-ores. Since that time I have continued this investigation at intervals with the following results. In the papers previously presented to the Institute I made no attempt to make compounds containing more than two substances. Since then I have endeavored to make more complex compounds. The experiments consist in fusing mispickel free from gold with a certain amount of metallic gold, and experimenting with that; also fusing the same mineral with sulphide of antimony, and fusing iron pyrites with gold and compounds of antimony. The mixture was made with mispickel taken from a vein not far from Stamford, Conn., absolutely free from gold. It was fused

Jan 1, 1884

By R. I. Jaffee, H. R. Ogden, D. J. Maykuth

IN THE past year, Jaffee and Campbell&apos; and Finlay and Snyder2 reported on the mechanical properties of titanium-base alloys, some of which were in the same ranges of composition as are covered in this paper. In this paper, evidence confirming that given by Finlay and Snyder on the effects of carbon, oxygen, and nitrogen on titanium will be presented; and, in addition, new data will be given on the effects of these elements on the flow properties and phase transformation of titanium. Materials and Preparation of Alloys The preparation and general properties of iodide titanium have been adequately described elsewhere.&apos; , As-deposited iodide titanium rod, prepared at Battelle, of Vickers hardness less than 90 was employed as the base metal in the present work. This was the same material as that used by Finlay and Snyder.2 The probable analysis reported by them for standard quality metal holds here also: N 0.005 pct, 0 0.01 pct, C 0.03 pct, Fe <0.04 pct, A1 <0.05 pct, Si <0.03 pct, and Ti 99.85 pct. Carbon was added in the form of flake graphite supplied by the Joseph Dixon Crucible Co. Oxygen was added in the form of c.p. grade TiO, powder, produced by J. T. Baker Chemical Co. Nitrogen was added in Ti3N4 powder, supplied by the Remington Arms Co. Individual ingots weighed 7 or 8 g. Carbon, oxygen, or nitrogen was added by placing the corresponding powder in a capsule made from as-deposited iodide titanium rods and melting the capsule with the balance of the charge. The charge was are-melted with a tungsten electrode on a water-cooled copper hearth under a partial vacuum of very pure argon (99.92 pct minimum). Melting was practically contamination free. Vick-ers hardness increases of less than 10 points were normal for unalloyed iodide titanium control melts. Nitrogen analyses of are-melted iodide titanium showed a nitrogen content of 0.005 pct, about the same as is present in the as-deposited rod. No tungsten pickup was found in a melt of iodide titanium analyzed for tungsten. Weight losses in melting nitrogen-free alloys were very small and varied consistently from nil to 0.015 g (0 to 0.2 pct). This permitted the use of nominal composition for these alloys. Chemical analyses made for carbon, which can be analyzed conveniently by combustion methods, justified this procedure. Where nitrogen was added, considerable splattering took place. Here it was necessary to analyze for nitrogen by the Kjeldahl method. The ingots were hot rolled at 850°C to about 0.045 in. thick. After hot rolling, the strips were descaled by mechanical grinding, and then given a cold reduction of 5 to 10 pct to insure a uniform thickness throughout the length of the specimen. The edge strips and the tensile strips were annealed in a vacuum of 1x10-4 mm Hg pressure for 3 1/2 hr at 850°C and furnace cooled. Methods of Investigation Hardness Measurements: At least five Vickers hardness measurements were taken using a 10-kg load on each sample in the following conditions: (1) top and bottom of each ingot, (2) top and bottom surface of as-rolled and annealed sheet, and (3) on cross-section of annealed sheet and all quenched specimens. Tensile Tests: Tensile tests were conducted on Baldwin-Southwark testing machines having load ranges of 600 or 2000 lb. Tests were made on 1-in. gauge-length specimens, 3 1/4-in. overall length, 1/2 in. wide, 0.040 in. thick, with a reduced section 1 1/4 in. long and 0.250 in. wide. Two SR-4, A-7 strain gauges, one mounted on each side of the specimen, were used to measure the strain over a limited range to determine the modulus of elasticity. After the modulus of elasticity readings had been taken, load vs. strain readings were taken, using only one strain gauge, at increments of 0.0001 in. until the yield points were passed and then at 0.001-in. increments to the limit of the strain-gauge indicator (0.02 in.). Strain readings above 0.02 in. per in. were taken every 0.01 in., using dividers to measure the strain between the 1-in. gauge marks until the maximum load had been reached. Crosshead speed, when using the SR-4 gauges, was 0.005 in. per min, and, when using dividers, 0.01 in. per min. Flow Curves: Flow curves were determined using the true stress-true strain data obtained during the tension test. The usefulness of this type of information has been dealt with very adequately elsewhere by L. R. Jackson,&apos; J. H. Hollomon,6 and many others. Flow curves of true stress vs. true strain could be converted to the more conventional cold-work curve of 0.2 pct offset yield strength vs. percentage of cold reduction by means of the transformation, 1/1 = 1/1-R, where R is the fraction reduction in cold working. Thus, the true strains corresponding to percentage reduction can be calculated, and the 0.2 pct offset yield strengths scaled off the — 6 curve by taking the true stresses corresponding to the values of 6 + 0.002 strain. Heat Treatment: For the transformation studies, the alloys were heat treated in a horizontal-tube furnace using a dried 99.92 pct argon atmosphere, and quenched into water. Essentially no contamination was found after several hours of heat treatment at temperatures up to 1050°C. Metallography: Specimens were prepared in the

Jan 1, 1951