Search Documents

By G. S. Hume

Production of petroleum and natural gas increased in Canada in 1939 principally because of new wells in Ontario and Alberta. Turner Valley The Turner Valley field, Alberta, yielded 7,456,000 bbl. of petroleum in 1939 in comparison with 6,703,548 bbl. in 1938, an increase of 11 per cent. Turner Valley now supplies 96 per cent of all petroleum produced in Canada (Table 1). The Turner Valley field (Table 2) has reached a position where it call supply much larger volumes of petroleum than the Prairie market is capable of consuming. The allowable production is under the jurisdiction of the Petroleum and Natural Gas Conservation Board of Alberta and the daily rate is set from time to time as warranted by the demand. During June the allowable reached a maximum of 27,000 bbl. a day. This, however, was a temporary situation due in part to the completion of a new British American Oil Co. refinery in Calgary capable of processing 5000 bbl. a day and with a storage capacity of about 100,000 bbl. The maximum consumption was reached during the harvest season with

Jan 1, 1940

By C. V. Milikan

Allocation of allowed production in a prorated field by the use of bottom-hole pressures is a method which is sound in theory. Thus far it has had limited application because the experience in correlating bottom-hole pressures with the depletion of wells or fields is not sufficient to interpret all the pressure changes. With additional data and more general knowledge of bottom-hole pressures their use in proration will probably become common. Bottom-hole pressure is the pressure at or near the bottom of a well. It is usually determined at the face of the producing horizon. Bottom-hole pressure measured while the well is producing, may be called the bottom-hole producing pressure or bottom-hole flowing pressure. If the well has been shut in or shut down long enough for the pressure in the producing horizon within the drainage area of the well to equalize, it may be called the reservoir pressure. The allowable production from a prorated field may be allocated to the individual wells or leases by three methods: 1. Bottom-hole producing or flowing pressures. (a) The potential capacity of a well to produce. (b) A uniform differential pressure while producing at the allowed rate. 2. Reservoir pressures. 3. A combination of bottom-hole producing pressures and reservoir pressures. In most prorated fields the allowed production is allocated to the individual wells or leases in proportion to their individual potentials. This method is based on the theory that there is a direct relationship between the permeability and the porosity of the reservoir. More directly stated it means that there is a direct relationship between the amount of oil in the reservoir and the rate at which it will move through the reservoir. While in general this relationship is true, it may vary considerably in different wells. Furthermore, in many wells the capacity of the reservoir to deliver oil to the well is greater than the capacity of the flow string to deliver oil to the surface. It is especially true where the potential is determined by flowing through tubing or by pumping.

Jan 1, 1933

By J. A. Faucher

The mining industry has undergone significant technological advances in metallurgical process methods in recent years. The 1000 tpd concentrator of St. Lawrence Colum-bium Metals Corp. portrays the continuing effort made by the industry to achieve economical concentration of new and difficult ores. During the active search for sources of uranium in the early fifties, radioactive minerals were found in the Oka district near Montreal. The compatatively small quantities of uranium which were found occurred in association with widespread columbium (niobium) mineralization which included perovskite, a calcium titanate containing roughly 40% Cb2O5; niocalite, a silicate containing some 20% Cb2O5; and pyrochlore, a calcium niobate containing 45 -70% Cb2O5 as well as fluorine and some water. An idealized formula for one type of pyrochlore is: A typical chemical analysis of pyrochlore is shown in Table I. An important feature of this analysis is the lack of tin, lead, sulphur and P2O5 which conforms with the requirements of most consumers. In general the cerium content varies with sodium content and any increase in Ta2O5 lowers the Cb2O5 content of the concentrate. However, Ta2O5 rarely exceeds 0.5%. The carbonatite host rock of the columbium mineralization has the average mineral composition shown in Table 11. In Table 11, the term "diopside" is used to cover all silicates except mica which is shown separately because of the problems involved with its separation during the concentration process. In some ore zones, small quantities of rare earth minerals, such as monazite are present.

Jan 1, 1964

By H. D. Colson, Robert A. Rapp

When a binary alloy is oxidized to form simultaneously an internal oxidation zone and an external scale which grows at a constant rate, the oxidation should reach a condition of steady shale, in which the internal oxidation zone is maintained at a time-independent thickness. Assuming an ideal model for the steady-state oxidation, the diffusion equation is solved for the steudy-state concentration profiles for oxygen and alloying- element in the metal. A theoretical prediction of' the steady-state thickness of the internal oxidation zone is made in terms of the experimental parameters. FOR the oxidation of binary alloys, Rhines, Johnson, and Anderson,1 as well as Mask: have derived equations describing the kinetics for the simultaneous formation of an internal oxidation zone and an external scale which was assumed to mow according to a parabolic rate law. Experimental determinations of internal oxidation zone thicknesses beneath a Cu2O scale for Cu-Be and Cu-A1 alloys3,4 have shown some deviation from Maak's theoretical expressions, because the ideal model assumed for the calculation is not met experimentally. Some pure metals, such as columbium and tantalum oxidize at elevated temperatures and high oxygen pressures to form nonprotec-tive external scales which thicken at a constant rate. If such a base metal is alloyed with a solute element which may form a more stable oxide than the solvent oxide, then internal oxidation of solute may occur beneath the growing external scale. A review of the internal oxidation of alloys has been published recently.5 The purpose of this paper is to analyze theoretically for a binary alloy the kinetics for the simultaneous formation of an internal oxidation zone and an external scale which grows at a constant rate. Consider an alloy A-B in which A is the more-noble solvent and B is the less-noble solute. The solute oxide is assumed to precipitate in internal oxidation as stoichiometric particles of BO, which are assumed to have a negligible solubility product in the A matrix. It is further assumed that the diffusion of oxygen through the zone of internal oxidation is not impeded by previously precipitated BO, particles. The specimen is assumed to be sufficiently thick so that the solute content in the center of the specimen does not change. For consistency: the following notation of Maak2 has been used:

Jan 1, 1967

PERSONAL (Members are urged to send in for this column any notes of interest concerning themselves or their fellow-members.) Members and guests who registered at Institute headquarters during the period June 10 to July 10: J. C. Ralston, Spokane, Wash. E. P. Ashmore, So. Porcupine, Ont., Can. William H. Yeandle, Jr., Mexico City, Stuart Croasdale, Denver, Colo. Mexico. W. E. Hopper, Houghton, Mich. W. C. Minsch, Mexico City, Mexico. D. W. Brunton, Denver, Colo. H. V. Winchell, Minneapolis, Minn. Fred Crabtree, Pittsburg, Pa. W. G. Swart, Denver, Colo. Robert S. Lewis, Salt Lake City, Utah. D. F. Schindler, Madison, Wis. Noel Cunningham, Timmins, Ont., Can E. R. Pettebone has just been elected a Trustee of the Pennsylvania State College, being supported by the votes of the delegates of the Pennsylvania Anthracite Local Section of the Institute and the Engineers' Society of Northeastern Pennsylvania.

Jan 8, 1914

By W. N. Best

(San Francisco Meeting, September, 1915) INTRODUCTION CRUDE oil attracted attention because of its excellence as a fuel for open-hearth furnaces; for making crucible steel and brass; for melting copper, lead, tin, zinc, nickel, silver, malleable iron, gray iron; and for the production of steam in all sizes and types of boilers. For heating furnaces, mold-drying ovens, core ovens, ore roasters, calciners, hot-air furnaces, sand drying, asphalt road work, etc., its superiority over other fuels is due to the fact that the heat is at all times under perfect control, so that a constant temperature may be attained and maintained at the will of the operator. This means a maximum amount and uniform quality of work. Crude oil is of two kinds, paraffine base and asphaltum base, and varies from 11 to 46 gravity Baumé. The light-gravity oil does not require heating before use; but oil of less than 20 gravity Baumé should be heated to just below its vaporizing point, in order to reduce its viscosity and to obtain the highest efficiency of combustion. Heavy California oil vaporizes at 230°'F., Mexican crude oil at from 175° to 210° F., and Beaumont, Texas, oil at 142° F. Fuel oil vaporizes at 130° F.

Jan 8, 1915

By Carl Samans

IN their recent complete review of the subject of age-hardening,1 R. F. Mehl and L. K. Jetter classify the main types of precipitation-hardening alloys under two headings, depending upon the nature of the precipitate and the character of the precipitation. In the alloys falling under the first heading, which display "continuous precipitation" and are typified by the aluminum-copper alloys, "precipitation seems to occur without much regard to grain boundaries and apparently at much the same rate at every point," although an acceleration in regions plas-tically deformed has definitely been established .2 In the second type of alloys the precipitation is "discontinuous," as in the copper-silver system for example, and "seems to start in restricted regions, primarily those contiguous with the grain boundaries, and to spread inward in an advanc-ing wave." The reasons for the occurrence of these two greatly different types of precipitation are unknown, as are those for many other reactions that take place in the solid state. In the present paper only the first or "continuous" type of precipita-tion will be dealt with, for which a complete crystallographic mechanism has been worked out for the process of precipitation from a supersaturated solid solution of copper in aluminum. Based upon this mechanism, an explanation of the various property changes found experimentally will be developed in the second paper of this series. In later papers "dis-continuous precipitation" in copper-silver alloys will be explained, and an effort will be made to rationalize the two processes and types of precipitation.

Jan 1, 1940

A B Cummins President James C Gray, President-Elect J W Woomer, Past President C E Lawall, Eastern Regional Vice-President Donald W Scott, Central Regional Vice-President H C Weed, Western Regional Vice-President Nathaniel Arbiter, Treasurer John Cameron Fox, Secretary AIME 29 W 39 St New York 18, N Y

Jan 1, 1960

By D. J. Carney, R. L. Stephenson

M. O. Holowaty (Inland Steel Co., Chicago)—Messrs. Stephenson and Carney should be commended on the presentation of this very interesting paper. They have introduced new ideas on sampling of sinter and have thereby made a valuable contribution to the qualitative evaluation of sinter. The paper undoubtedly presents a novel approach to the problem of sinter sampling and this is to be regarded as its main value. Sampling of sinter from the pallets prior to the discharge is by no means new. This sampling procedure was used in the past by Philbrook; Hamilton and Ameen and others. The sampling basket used by the authors of this paper, however, permits one actually to obtain a good sample of the sintering mixture. The basket which can also be described as a removable pallet goes then through the entire process of sintering and thus offers a sample which is positively representative of the batch in question. The authors' method of evaluating physical properties of sinter seems to be not altogether clear, however. It is felt that the following points should be clarified: I—In the section describing the shatter test the authors state that a 5-lb sample was used in the actual tests. There is no mention of the initial size of sinter particles used and the method of obtaining this 5-lb sample from the sinter cake weighing about 100 to 120 lb. It is also surprising that the sample was dropped from a height of 3 ft instead of the conventionally used 6 ft. Unfortunately there is no mention of the number of drops to which the sample was subjected. 2—The tumbler test used by Messrs. Stephenson and Carney in testing the samples of iron ore sinter was performed in a standard ASTM coke tumbling drum. The drum measures 3 ft in diam and is equipped with two 3-in. lifter bars. The distance of fall in this testing drum is identical with the distance used in the previously described shatter test. The number of drops in the tumbling drum is approximately double the number of revolutions. The basic difference then between the drop-shatter test used by Stephenson and Carney and the tumbling test seems to be the number of drops to which the sample is subjected and the abrasive action to which the sinter particles are exposed in the rotating drum. In any case, the choice between the shatter test and the tumbler test seems to be only a matter of taste and convenience. 3—The authors of the paper state that "in order to insure getting results that were representative . . . the entire sample obtained by means of the sampling basket was used as the starting material for the tumbler test. If the sample broke in pieces, all the pieces were used regardless of their size." The initial size of the material is known to be a very important factor, influencing seriously the final size of the particles. This should be particularly important in case of hard sinters. It seems also very troublesome and inconvenient to charge 12-in. cubes of sinter weighing about 100 lb into the testing drum. This could be eliminated by taking a standard fraction of somewhat smaller particles.

Jan 1, 1954

By Harlowe Hardinge

THE sound made by ball, pebble and rod mills has long been used by the operator as the "telltale" of their operation. The nature of this sound depends upon local conditions and the type of mill used. By experience an operator can tell whether the mill is running properly or not. Some operators are able to detect the difference in sound much better than others and get better results running the same mill tinder the same conditions. The automatic operation of a mill using sound as the fundamental means for maintaining control presents many problems. The satisfactory solution of these problems requires, for given operating conditions, a greater average output, with improved product for subsequent processing, than can be obtained by manual control.

Jan 1, 1939

By L. A. Rapoport, W. J. Leas

The original Burkley-Leverett theory has been extended and a more detailed formulation of the waterflood behavior in linear horizontal systems is presented. Particular consideration has been given to the evaluation of capillary pressure effects and differential equations permitting an explicit evaluation of these effects have been derived. On the basis of the developed theory it is recognized that the flooding behavior is dependent upon the length of the system and the rate of injection. At the same time it has been determined that systems of different lengths yield the same flooding behavior if the injection rates and or the fluid viscosities are properly adjrrsted or "scaled." It has also been found that the sensitivity of the flooding behavior with respect to rate and length decreases as any one of these {actors increases in value and that for sufficiently long systems and high rate.; of water injection the flooding behavior becomes independent of rate and length. or "stabilized." To such stabilized conditions the theory formulated by Buckley and Leverett is applicable. A number of laboratory flooding tests have been made and good agreement Iraq been found between theory and experimental observations. The experimental results are discussed and it is shown that under field conditions the flooding behavior is usually stabilized. As a result of these finding; a procedure is indicated for evaluating field performances either on the basis of tests performed with commonly available core samples or by means of calculations using relative permeability data INTRODUCTION In recent years the development of methods for evaluating oil recovery by waterflooding has been the object of considerable research. A theoretical analysis of the mechanisms involved in the displacement of immiscible fluids was originally established by Buckle!- and Leverettl and experimental investipatio~~s have been made by numerons workers." Many of the experimental results are in mutual agreement and bear out several significant features of the flooding mechanism as predicted by theory. Thus it lias been generally recognized that a flood corresponds to the movement of a steep saturation hank or "front" (primary phase), followed by additional gradual oil displacement (subordinate phase). It has also been found that for any porous medium the flooding behavior is largely dependent upon the oil-water viscosity ratio and that for increasing values of this ratio the relative importance of the primary displacement phase decreases while that of the subordinate phase becomes more pronounced. Although the studies to date have clarified certain aspects of the flooding process. they have given rise to observations of a somewhat contradictory nature that cannot he explained in terms of the original theory. These observations pertain mainly to the effect of injection rate or pressure gradient upon recovery. Some investigators report laboratory tests that indicate incresing oil recoverieq with increasing rates of water injectill, others find the flooding behavior to be independent of and other. mention lower oil recoveries with increased injection rates.3 The conflicting evidence indicated above creates considerable uncertainty with respect to laboratory testing procedures and the utilization of the resulting data for field evaluations. The principal purpose of this paper, then, is to resolve these Uncertainties by means of a comprehensive theoretical and experimental investigation of the flooding meanism. THEORETICAL DEVELOPMENT Derivation of Flooding Equations The mathematical description of transient flow phenomena is based upon the consideration of the various processes occurring during an infinitesimal time interval in an infinitesimal volume element and upon the correlation of these processes with those occurring in the adjacent elements. The volume elements are defined as being infinitesimal in comparison to the overall dimensions of the porous system, yet each sufficiently large so aS to encompass the full range of pore openings encountered throughout the system. If a porous system can arbitrarily be subdivided into an infinite number of volume elements all possessing the same distribution of pore openings and if this distribution is unformly continuous. the system may be said to be homogeneous. Such a homogeneous porous medium is considered in the present studivs. It is furthermore postulatecl that only oil and water are present in the pornu wediu. that they act a- totally incompressible and immiscible fluids. and that gravity effects are negligible. In n linear flow system of unit cross sertional area. as treated here. the infinitesimal volume element.; to he considered are cylindrical ".slices" of thickness dx. oriented perpendicularly to the direction of flow. The equations applicable to any such volume element. at my time. describe the movement. of oil and water across the element:

Jan 1, 1953

By Y. J. Wang

A graphical technique by which the operating points for a two-fan ventilation system can be represented as the intersection of the modified fan curves is described. In constructing the diagram, the air quantities associated with the fans are considered to be independent variables and used as the axes of a rectangular coordinate system. The diagram may include, in addition to the modified fan curves, contour lines for resistances, pressures, and air powers. Procedures for drawing the diagram are discussed and illustrated with an example of the ventilation system.

Jan 1, 1986

By Nathaniel Herz

The formula very frequently used for computing the economical size of pipe to transmit compressed air is that of D'Arey, as follows: D = cV w1l Where, D = the volume of compressed air delivered in cubic feet per minute, at the final pressure. c = an experimental coefficient determined for the various sizes of pipe, d = the diameter of the pipe in inches. 1 = the length of the pipe in feet. p, = the initial gauge-pressure in pounds per square inch, p2 = the final gauge-preesure in pounds per square inch. w1 = the density of the air, or the weight in pounds per cubic foot at the initial pressure, p1. The most common case is that in which the given quantities are: the quantity of air required, the length of the pipe, and the initial pressure. The method of solution is to assume a pressure-loss and to compute the remaining factor, cd5, thus giving the size of pipe corresponding to the assumed loss of pressure. It is always desirable to try two or more pressure-drops, in order to find the combination that is most satisfactory, since often a small change in the size of pipe will reduce or increase the loss of pressure several pounds. An alternative method is to assume a size of pipe and calculate the corresponding pressure-drop. Each method involves a series of tedious calculations to arrive at the most economical solution, and also requires the use of tables giving the constant, c, the density of the air, w1, and often, for convenience, a table giving the values of the expressions p1-p2 and c J I hare constructed a graphic chart, Fig. 1, for the solution of

Jan 1, 1913

By B. K. Larkin

Solutions to the diffusion equation for a line source located anywhere in a region bounded by a circular discontinuity are presented. Such solutions follow automatically from the Green&apos;s function presented by Jaeger.4 Petroleum industry applications of this problem would include transient compressible fluid flow in porous media bounded by a discontinuity. Since several recent papers have treated the subject in less general form, it would appear that many workers in this area of the petroleum industry are not aware of Jaeger&apos;s work. STATEMENT OF THE PROBLEM In several trearments1,2,3 of the transient flow of compressible fluids in porous media it was convenient to consider a region to be bounded by a circular discontinuity. In such a region (Fig. I), the properties in Region 1, r < a, are constant but different from the properties in Region 2, r > a. Hurst, l using the Laplace transform, obtained solutions for a line source located in the center of such a porous medium. The purpose of this work is to point out that a much earlier paper by Jaeger4 presents the solution for a line source located anywhere inside the discontinuity. The assumption is made that a line source may be used to approximate a well. In the following material it is convenient to use the terms source and well as being equivalent; however, the reader should remember the distinction in applications. SOLUTIONS Jaeger presented the Green&apos;s function for a line source, or well, in the composite region shown in Fig. 1. In the most general form, the solution for a system of j wells in Region 1, each producing at a time varying rate, qi (t), is

By Jean Herenguel

THE published work of Lacombe and Beaujard&apos; has demonstrated the interesting application of etch figures to the determination of crystal orientations in aluminum by a purely micrographic method. The geometry of these figures leaves no ambiguity and the method has the added advantage of being applicable to very small crystal units. These authors applied the technique to the study of high purity aluminum, and it has now been adopted buy Heren-guel and his collaborators to various researches on commercial aluminum, containing up to 1 pct Fe and Si. This must modify the opinion point,ed out by

Jan 1, 1953

By H. Foster Bain

THE "miracle of production." which was such an essential element in winning the European war, was nowhere more in evidence than in our Western States. In shipbuilding alone the Pacific Coast States -et a mark never before equaled, and in production of war goods of many kinds, both Rocky Mountain and Coast States accomplished more than their proportionate share if measured by population standards. This was only possible because of the building of immense new plants of many types, largely financed with Government money. Their operation has built up payrolls in the West and brought a measure of prosperity which Westerners are naturally anxious to have made permanent. A widespread doubt obtains, however, throughout the nation and even in the Western States themselves, as to whether, and if so to what extent, this may prove possible. The question has been raised as to whether the national treasury has not been raided to stock the Western ranges with a voracious breed of white elephant .

Jan 1, 1945

By E. C. Simmons

Uranium is an incompatible element with respect to the major rock-forming minerals crystallizing from granitic magma, entering instead trace minerals such as zircon. The relationship between the saturation limit (SL) for such a mineral and the bulk distribution coefficient (Do) for U is central to understanding the distribution of U and its availability to late-stage fluids that can form ore deposits directly, or labile U that can be remobilized later. Low SL values imply early crystallization of zircon, but in very small proportions, minimizing Do and maximizing the degree of enrichment of U in late-stage fluids. Thus, granitic rocks with low Zr contents (due to a low saturation limit for zircon) are most likely to evolve U-enriched differentiates; this will be reflected in a high U content of the zircons (but not necessarily high U abundances in whole-rocks). Thus, the ratio of the U content of zircon to the Zr content of the corresponding whole-rock is potentially a very useful parameter in identifying granitic rocks most likely to have U-enriched solutions associated with them. The granitic rocks associated with the U deposits of the Midnite mine area, Washington, have geochemical characteristics that fit the model presented very well. The rocks are very low in Zr (100 ppm) and contain zircons with extremely high U contents (3,000-4,000 ppm).

Jan 1, 1984

By A. D. Zunkel, A. H. Larson

Equilibrium arsenic contents of Pb-As alloys in contact with PbO-As2O3 slags containing less than 30 mol pct As2O3, were determined at 650°, 700: and 750 C in an inert at?rzosphere. In this temperature range, the arsenic content of the alloy increased with increasing temperature in the single-phase liquid slag region and decreased with increasing temperature in the two-phase slag region and the single-phase solid-solution slag region. The PbO-As2O3 phase diagram below 22 mol pct As2O3 was determined by thertrzal analysis and by application of a log ?As2O3/?PbO vS log XAs2o3 /x3pbO plot determined from the equilibrium actiuity data. The resulting phase diagram was not well-defined since the eutectic temperature was not detected in the thermal analysis experiments, although a region of terminal solid solubility of As2O3 was found. Results from the phase diagram determination are compared with an existing diagram in the literature. THIS experimental investigation is an extension of a study by the authors1 on the slag-metal equilibria in the systems concerned with commercial lead refining processes such as softening and dross fuming. The first part of this investigation was a study of the slag-metal equilibria in the Pb-PbO-Sb2O3 system. The only experimental work previously done on the Pb-PbO-As2O3 system was by Pelzel2,3 in which the phase diagram for the PbO-As2O3 system was determined below 50 wt pct As2O3 and the equilibrium constant for the reaction 3Pb + As2O3 + 3PbO + 2As was determined as a function of temperature. No slag-metal equilibrium data have been determined. It is due to the scarcity of information regarding the Pb-PbO-As203 system that this work was undertaken. This paper describes the determination of the slag-metal equilibria in the Pb-PbO-As203 system by equilibrating Pb-As alloys with PbO-As2O3 slags in an inert atmosphere, the effect of 1 wt pct additions of bismuth and copper on the slag-metal equilibria, and the PbO-As2O3 phase diagram both by thermal analysis and the use of the slag-metal equilibria data. EXPERIMENTAL Materials. The materials used in this investigation were analytical reagent-grade and assayed as follows: 1) 99.8 pct PbO (0.014 pct insoluble in CHJCOOH, 0.02 pct not precipitated by H2S, 0.1 pct CaO, and 0.08 pct SiO2); 2) 99.95 pct As2O3; 3) 99.99 pct Pb; 4) 99.0 pct As; 5) 99.99 pct Cu; and 6) 99.97 pct Bi. Room-temperature X-ray patterns revealed no detectable impurities in any of these materials. Apparatus for Equilibrium and Thermal-Analysis Determinations. The resistance-heated crucible furnace used in this investigation employed nichrome elements and was mounted so that it could be raised to surround the reaction tube during each experiment and, subsequently, lowered. A schematic diagram of the apparatus is shown in Fig. 1. Each charge was heated in a 3+-in.-OD by 31/2-in.-high 416 stainless-steel crucible placed in a 41/4-in.-1D by 18-in.-long fused-silica reaction tube which was closed at one end. On a shoulder around the crucible was placed a 3: -in.-OD by 12-in.-long open-end fused-silica condenser tube. The open end of the reaction tube was covered by a water-cooled brass cap with ports for 1) admitting an inert atmosphere to the system through a stopcock, 2) introducing a stainless-steel, motor-driven, paddle stirrer into the crucible, 3) evacuating the system with a mechanical vacuum pump, and 4) sampling the melt with Vycor sampling tubes. The brass cap was fitted to the open end of the reaction tube with a silicone gasket and collar clamp. The furnace temperature was controlled by a Barber-Coleman Capacitrol controller and a chromel-alumel thermocouple. Due to the corrosiveness of the melt, the controlling thermocouple also served as the measuring thermocouple. The temperature of the melt was calibrated against the controller temperature and was checked periodically during each test with a Vycor-enclosed calibrated chromel-alumel thermocouple. The temperature measurement and control can be considered accurate to ±3°C. Procedure. The charge placed in the crucible for each experiment consisted of 1000 g of Pb-As alloy and 300 g of PbO-As2O3 slag. The crucible was then placed in the reaction tube, the condenser tube was placed on the shoulder of the crucible, the silicone gasket and brass cap were fitted on the open end of the reaction tube, and the entire system was evacuated and filled with argon ten times. After the last flushing, a positive argon pressure of 1 psig was impressed on the system. The furnace was then raised to sur-

Jan 1, 1968

By W. H. HOWARD

Discussion of the paper of W. H. HOWARD, presented at the Salt Lake meeting, August, 1914, and printed in Bulletin No. 92, August, 1914, pp. 2029 to 2046. EDGAR M. DUNN, Anaconda, Mont.-Mr. Howard&apos;s contribution to the literature on the Cottrell, method. of electrostatic precipitation of flue dust and fume at Garfield has been read by us with peculiar interest for the reason that we have been experimenting with the same process at Anaconda for the past eight or nine months, with a view to adapting it, under the direction of Dr. Cottrell and the supervision of J. 0. Elton. and D. R. Kellogg, representing the Anaconda Smelter Commission, to the treatment of very large volumes of gases, using large pipe treaters and various forms of electrodes, with about 150,000 volts rectified current. For the amount of gas to be treated here the 5-in. pipe means a cost for installation that is practically prohibitive, clue to the tremendous number of pipes required, and we have been trying to cut installation costs by increasing the size of the pipes. All of our work is still in the experimental stage, but we have obtained good clearance on our mixed roaster and converter gases with a 3-ft. pipe treater 20 ft. long, and with 5 ft. velocity therein; and with a discharge electrode of a single No. 29 nichrome wire set in the middle of the 3-ft. pipe, with. a consequent electrode spacing of 18 in. The current used has been 150,000 to -160,000 volts, .and of course there have been troubles galore, relating particularly to insulation and rectifying. Blast-furnace gases did not give so good clearance, probably due to relative poverty in moisture and S03 content of blast gases to roaster-converter gases; making the blast gases the poorer in conductivity. Our experience has been so satisfactory that in our next experimental plant-built on a somewhat larger scale-we shall attempt a 4-ft. treater with greater electrode spacing, and a somewhat higher voltage-up to 220,000. As to fractional precipitation, mentioned by Mr. Howard, this idea was tried out at Anaconda last year (1913). Formerly our furnaces (Bruntons) roasting flue dust for the recovery of white arsenic, passed so great an, amount of dust to the settling kitchens that refining of this arsenical product was necessary to eliminate the 5 to 20 per cent. dust contained therein. Consequently the manufacture of As203 was effected in two stages, with a reverberatory roast of the first .product to obtain the final 99.5 per cent. As203. -

Jan 11, 1914

By U. C. Tainton

IN reviewing progress in zinc metallurgy during the last year or so one is reminded of the premise on which H. G. Wells based his "Food. of the Gods," namely that growth does not and cannot take place smoothly and steadily, but occurs in a series of bursts and intermissions: "It is as if every living thing has to accumulate force to grow, grows with vigor only for a time, and then has to wait for a space before it can go on growing again."

Jan 1, 1937