Search Documents

By Bill M. Stewart

Since 1974, a large amount of data has been developed concerning the physical properties and stability characteristics of waste generated by the mining and preparation of bituminous coal. However, very little information has been developed on the properties and characteristics of anthracite waste. During this Bureau of Mines research project, coarse anthracite breaker refuse from five sites in eastern Pennsylvania was sampled and the physical properties, which indicate stability characteristics, were determined in the laboratory. Coarse anthracite breaker refuse is quite similar to coarse bituminous refuse in chemical and mineralogical composition. However, the physical properties of the anthracite waste materials tested are different from those of coarse bituminous refuse. For the coarse anthracite breaker refuse tested, the average maximum laboratory density is 113.2 lb/ft3, the average angle of internal friction (direct shear) and average cohesion are 30.2° and 2.6 psi, respectively, and the average permeability (four sites) is 1.24 x 10-2 cm/sec. Stability analyses were conducted on six theoretical anthracite waste embankments. These analyses show the effects on minimum safety factors of geometry, phreatic surface level, and physical properties.

Jan 1, 1983

By Steven J. Schatzel, James Addis, K. Vaibhav Raj, Berk Tulu

The National Institute for Occupational Safety and Health (NIOSH) is conducting research to enhance methane control and mine ventilation practices at coal mines, as a method to mitigate hazardous work conditions. NIOSH researchers conducted case studies to investigate the effectiveness of existing systems and improve performance to decrease the potential for unplanned or excessive methane emissions. At one mine, drainage was influenced by hydrofracking inefficiencies where two of the six wells showed good frack development. Methane content was variable, from 300 ft3/t to 600 ft3/t. This paper also summarizes overburden movement during undermining and the estimated quantities of gas transported to the mine using FLAC3D and CFD modeling. The findings from this research effort highlight considerations based on specific mine conditions that may also be applicable to most longwall mines utilizing methane control systems.

Feb 1, 2025

By A. Thatcher, C. Day, C. Meyer

The purpose of this paper is to provide general information about the bioaccessibility of metals and specific information about the use of bioaccessibility in risk assessments (human health risk assessments [HHRA] or ecological risk assessments [ERA]) and a list of sites where regulatory agencies have approved the use of bioaccessibility data in risk assessment. The memorandum also cites current U.S. Environmental Protection Agency (USEPA) guidance as well as state specific guidance where applicable. BRIEF HISTORY OF METAL BIOACCESSIBILITY TESTING AND METHODS The bioaccessible fraction of a constituent is that fraction that dissolves or desorbs from its matrix (e.g., soil) in the gastrointestinal tract and is available for absorption (USEPA 2007a; ITRC 2011; ITRC 2017). This is different from the bioavailable fraction, which is the percentage of the amount of an element that an organism is exposed to that is absorbed by that organism during a given time under defined conditions (USEPA 2007a). The bioaccessibility factor is the percentage of a metal that is potentially available for absorption and, therefore, is a conservative estimate of the bioavailable fraction since all that is available for absorption may not ultimately be absorbed into the organism’s system. Currently, there are two main techniques for estimating bioavailability of metals within a medium: in vivo animal studies (time-consuming and often cost-prohibitive), and in vitro tests that simulate human, or animal digestion in a laboratory setting. In vitro and in vivo test methods and protocols have been extensively evaluated by numerous researchers (Ruby et al. 1996; Rodriguez and Basta 1999; Sips et al. 1998; Sips et al. 2001; Molly et al 1993; Oomen et al 2002; Kelley et al. 2002; Oomen et al. 2003; Furman et al. 2006; Drexler and Brattin 2007; Basta et al. 2007; Wragg et al. 2009; Wragg et al. 2011; Chaney et al. 2011; Bradham et al. 2015; Bradham et al. 2018). The most recent scientific literature demonstrates that protocols used to estimate the bioavailability of metals to mammals also predict bioavailability of metals to birds as well (Beyer et al., 2016).

Jan 1, 2019

By John R. Benham

In 1979 and 1980, the U.S. Bureau of Mines and U.S. Geological Survey conducted a mineral survey of the 20,500 acre Black Butte RARE II area (No. 5102) in the Los Padres National Forest (fig. 1). The work by the Bureau of Mines indicates that the potential tor mineral resources in the area is low. Samples of outcrops and stream channels contained no economic minerals. A mercury deposit near a granodiorite-sedimentary rock contact occurs 2 mi northeast of the study area, but similar deposits have not been discovered within the area. Geothermal potential exists near Tassajara Hot Springs, but no thermal springs occur in the area; nor have oil, gas, or coal resources been found.

Jan 1, 1982

By D. L. Cluff

Ventilation Air Methane (VAM) is a high volume low concentration methane source. The capture or use of methane from VAM is challenging, which results in the routine discharge of methane into the atmosphere. Mitigating VAM has the benefits of providing an energy source and reducing the atmospheric Greenhouse Gas (GHG) burden. The GHG radiative forcing effect of methane is 17?23 times as potent as carbon dioxide on a 100-year time horizon. Thus, any reduction in atmospheric methane would be beneficial. The calorific value of methane is 55.5 MJ/Kg; therefore, a 100 m3/s flow with VAM concentrations from 0.1?1% can provide 3.8?38 MW of exploitable power. Strategies to mitigate VAM such as: Thermal Flow Reverse Reactors (TFRR), Catalytic Flow Reverse Reactors (CFRR), Lean Burn and Catalytic Gas Turbines, Biothermica Vamox®, Megtec VOCSIDIZER©, and Vamcat? are briefly reviewed. The review of VAM mitigation technologies reveals disadvantages such as the need to maintain a minimum internal heat capable of oxidizing the methane. This requirement uses all of the available methane up to the point of reaction sustainability and up to half at the highest methane concentration in VAM. Some systems may introduce a pressure drop to the ventilation system, which would impinge on the existing ventilation system design. These impediments necessitate the development of a more amenable technology. In the proposed system, gas turbines (GT), coupled to a combustion chamber with an external fuel supply, assist the combustion of the VAM. The combustion-chamber coupled system provides electricity, while the heat contained in the GT exhaust gases increases the temperature of the VAM, encouraging the development of a flame inside a combustion chamber. The flow from the combustion chamber streams through a primary air/fluid heat exchanger capable of producing steam of a high enough quality to generate electricity using conventional steam turbines. The residual heat after primary extraction, directed through other equipment, provides additional heat based products such as industrial scale dry air, chilling by an absorption chiller or hot water. The overall design of the system is scalable for low to high VAM flows or variations in concentrations and is capable of providing the company or community with heating, chilling, hot water, electricity or motive force as needed by the particular site or community. The Multi-generation system uses heat from three sources to provide clean efficient energy while mitigating the atmospheric emissions of methane. These sources are heat from the GT, often considered waste heat, heat from fuel injected into the igniters and heat from the VAM. The opportunity to collect carbon credits may improve the economics. In order to design a system with this capacity, a detailed analysis of the combustion characteristics of three separate flows is required. VAM is the main airflow, having the highest volumetric effect, while the GT exhaust and the additional fuel added to the hot exhaust flow of the gas turbine are lower flows, but have a higher velocity and temperature. The aim of the modeling undertaken in this work is to establish the combustion dynamics, degree of pre-heating required and the geometry essential to the design of combustion based VAM mitigation multi-generation systems.

Aug 1, 2013

By B. F. Giyani, A. Salama

Tanzania is a country with a variety of mineral deposits, including metallic minerals, gemstones, mineral fuels, industrial minerals, and critical minerals. This study provides an overview of mining legal framework, mineral occurrence and production, challenges in the mining sector, and government initiatives. The aim is to demonstrate the development of the mining sector in Tanzania and explore the potential for further mining investment in the country. The mineral production data showed generally increasing trends over the years, for example, gold production increased from 42 tonnes in 2018/2019 to around 50 tonnes in 2023/2024. Despite the growth, the mining sector encounters several challenges, including a lack of detailed geological information on mineral deposits, inadequate infrastructures in some remote mining sites, the existence of informal artisanal miners, and mineral smuggling. The Tanzanian government has introduced several initiatives to address these challenges, including carrying out the highresolution airborne geophysical survey to increase geological information in some areas, the formalisation of artisanal and small-scale mining, establishing mineral markets to combat mineral smuggling, and encouraging mineral value addition within the country.

Oct 24, 2025

By Robert L. Lappi

This report covers the final phase of a project demonstrating the economic efficiency of cross-ridge mountaintop coal mining. A demonstration mine was established at Big Wheel Gap in northeastern Tennessee. Not only was cross-ridge mining feasible for the selected site, but parallel cut methods could not be used due to a deficit in available spoil storage. Cross-ridge mining permitted coal extraction at a cost almost identical with costs simulated by computer projections using mathematical optimization techniques. No unexpected environmental problems were encountered. Volume I is accompanied by Volume II which describes the MATHMINE Mine Simulation System, software used to support the mining demonstration.

Jan 1, 1984

This report is the 22d in a series summarizing Bureau of Mines research and technologic work on coal and related investigations.2 3/ A summary of work published during 1957 and of work in progress is presented. Details regarding the subjects treated in the publications may be found by referring to articles cited in the footnotes. The objective of the coal work of the Bureau of Mines is to obtain information that will lead to improved production and utilization of coal, thus conserving a most important national asset.4 5/ Though studies of mining methods and exploration of various coalfields ma; contribute directly to improved production, no less so does the work in health and safety. The many problems relating to chemical and physical properties of coal reflect the need for an understanding of these properties for the most effective use of coal in its various fields of application and for the development of new methods of processing coal. Studies of existing and proposed processes of combustion, carbonization, gasification and hydrogenation of coal are necessary for increased efficiency in its use. Engineering service provided by the Bureau is of direct value in the conservation program in preventing waste. Stations where the main coal activities of the Bureau are carried out are shown in the following list:

Jan 1, 1959

By C. Sunderman, G. Feagan, C. Stazick

Galvanic corrosion between dissimilar materials, such as steel and graphite, leads to safety concerns for many industries, including mining. In this study, researchers from the National Institute for Occupational Safety and Health (NIOSH) analyzed rock samples from two mines in the United States that exhibit electrochemical properties similar to graphite through laboratory measurements to investigate their observed in-situ influence on underground metal support. Uniform corrosion rates of mild steel coupons, inflatable bolt coupons, and friction bolt coupons galvanically coupled to rock samples were obtained using both potentiodynamic polarization and zero resistance ammetry. Increased uniform corrosion rates were witnessed between the coupled rock and steel system, over those of just the steel alone. Surface analysis of the metal samples showed the presence of pitting corrosion, reflective of bolt samples removed from partner mines. Corrosion pitting of ground support structures in contact with graphitic rock in underground mines poses safety concerns for mine workers by increasing the rate of corrosion and decreasing bolt strength over time and will be further investigated for intervention strategies.

Feb 1, 2023

By R. E. Hershey

1. Reserves were estimated for three coal beds: Lantana, Sewanee, and Richland. 2. Known measured and indicated reserves for all beds, based on a minimum thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated at 34 million short tons as of Januray 1, 1954. Of this total, 15 million short tons represents coal 28 inches and more thick. Areas in the beds were omitted from the estimate because available data relative to the bed characteristics were insufficient to permit making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves determined by this investigation.

Jan 1, 1956

By McHenry Mosier

Mechanical loading, adopted long ago in open-pit, coal, and non-metal mines, was not used extensively in underground metal mines until the World War. In less than a decade it became standard practice in underground work in many mining districts. In 1924 the Missouri School of Mines and Metallurgy, in cooperation with the Federal Bureau of Mines, published a bulletin entitled "Mechanical Underground Loading in Metal Mines," which was prepared by Charles E. van Barneveld, mining engineer, Bureau of Mines.

Jan 1, 1940

By Audrey A. Soja

The Bureau of Mines investigated beryllium resources, production methods, and production costs to estimate the quantity of beryllium available for future use. Eight mining districts and 12 deposits are included in the study; lack of data precluded the evaluation of resources from 6 nonproducing and undeveloped deposits. The study revealed that demonstrated beryllium-bearing resources should be sufficient to meet domestic needs and those of other market economy countries (MEC's) well into the 21st century. Total demonstrated beryllium-bearing in situ resources from MEC's are estimated at 118 million metric tons (Mmt) of ore containing approximately 33,000 mt beryllium metal. Approximately 111 Mmt ore containing 29,000 mt beryllium was included in the cost analysis and availability sections of this study. Three Brazilian districts currently produce beryl ore, and one domestic company, Brush Wellman Inc., produces bertrandite ore. Brush Wellman Inc. owns and operates the only MEC facility in the Western Hemisphere for extracting beryllium values from beryl and bertrandite and is the beryllium industry's only fully integrated corporation.

Jan 1, 1986

By Bureau of Mines Staff

Coal research and related activities in 1964 by the Bureau of Mines resulted in many advances in the production, preparation, and utilization of this valuable natural resource. Mining research during the year was marked by work on hydraulic mining, coalbed degasification, mine drainage control, mine sealing, strip-mine rehabilitation, and quenching of mine-refuse fires. Bureau research continued to produce information leading to increased safety in underground mining. Such research included roof and rib control via bolting and bonding, pressure monitoring of coal and mine rock during mining operations, and development of safety devices for detecting conditions leading to roof falls. Other safety work was continued on methane detectors, coal-dust suppression, and mine venti lation equipment and techniques. Mine explosion and explosives research, mine equipment and materials, safety rule modernization, and safety education and training of mine workmen were continued. Coal storage and preparation work in 1964 ranged from freezeproofing of lignite for rail shipment, through washability studies of coals and washing equipment, to research on new ways to remove ash and sulfur from coal. Electric power production, which ,accounts for a major portion of the market for coal, received further study. Unique power generation systems, inc luding coal-burning gas turbine and megnetohydrodynamic generators, were intensively investigated. Conventional power systems were improved through continuation of work on furnace performance, powerplant stack gas purification, and engineering and boiler water service.

Jun 1, 1965

By M. Riddell

This paper describes the incipient heatings that occurred below ground in the High Main and Main seams at the mine between the years 1963 and 1966. The possible causes, effects and activities associated with such heatings are discussed in an attempt to establish the precautions necessary to minimize such occurrences. The assessment of as many "norms" as possible is made to enable the earliest detection and level of activity to be determined.

May 23, 1905

By Yi-Shen Li

This report has been prepared by Lockheed Missiles & Space Company, Inc. (LMSC), under United States Bureau of Mines Contract No. H0220040 dated 21 June 1972 for the design, development, fabrication, and certification of the One-Hour Self-Rescue Breathing Apparatus (PBA). The PBA is a self-contained, oxygen-generating, CO2-removing closed-loop breathing apparatus that provides a minimum of 1 hour of breathable atmosphere during escape from a mine with a contaminated or oxygen-deficient atmosphere. This Cost-Plus-Fixed-Fee (CPFF) contract has been successfully completed in a three-phase program. The Phase I tasks included the design, development, and fabrication of prototype units developed at LMSC in accordance with the requirement of the Code of Federal Regulations (CFR) Title 30, Chapter 1, Subchapter B, Part 11 (Appendix A), and was submitted to the National Institute for Occupational Safety and Health (NIOSH) for joint NIOSH and Bureau of Mines certification testing.

Jan 1, 1974

By J. Morkel

During research on mainly the weathering of kimberlite, it became evident that its mineralogical composition is an important factor in the complex process of physical and chemical disintegration. The mineralogy of tuffisitic kimberlite breccias from two localities, the Cullinan and Venetia mines, is compared with special reference to the occurrence of associated clay minerals. The clay mineral composition influences the engineering properties of these rock types. It is illustrated how the presence of swelling clay components can be confirmed by ethylene glycol treatment and chlorite minerals by heat treatment using X-ray diffraction. Smectites are present in both tuffisitic kimberlites, dominant at Venetia while chlorite is more frequent at Cullinan. More tuffisitic kimberlite breccias samples from venetia were also characterized. It was found that kimberlite disintegration is correlated with the presence and abundance of smectite.

Jan 1, 2006

By T. E. Gray

This report describes the preparation characteristics of the signifi¬cant coalbeds in Preston County, W. Va. It is one in a series of reports planned to determine coals suitable for the production of metallurgical coke, either as mined or after beneficiation. Over 2 million tons of coal was produced in Preston County, W. Va. in 190, none of which was cleaned mechanically. Estimates as of January 1, 1959, indicate that more than 3 billion tons of coal remained in the county in beds 12 inches or more thick. The Bakerstown, Mahoning, Upper Freeport, and Upper Kittanning beds were selected by the Bureau of Mines for study based on current production and estimated minable reserves. Sample locations were selected after study of the literature, conferences with mining engineers and mining company offi¬cials in the field, and examination of available sites. Four samples were collected from the Bakerstown and Upper Freeport beds and one each from the Mahoning and Upper Kittanning beds.

Jan 1, 1961

By Terry J. Close

In 1985, at the request of the U.S. Bureau of Land Management, the U. S. Bureau of Mines studied part of the 56,623-acre South McCullough Mountains Wilderness Study Area (NV-050-435) in order to evaluate its identified mineral resources. The area studied is located in Clark County, NV, about 30 miles southwest of Boulder City. No mineral resources were identified. The study area contains the eastern part of the unorganized McCullough Mountain (McClanahan) mining district which has had no recorded production. Between 1911 and 1982, 23 lode claims were located in the part of the mining district that is in the study area; four of these claims are currently held by assessment (1986). A total of 11 mineral sites were found and examined during the U.S. Bureau of Mines investigations; 26 mine workings were examined. Of the 11 sites, four are within the study area, and seven are nearby. Of the seven nearby sites, six are adjacent to the west boundary and consist of precious-and base-metals bearing vein occurrences in metamorphic rocks. The seventh site is near the east study area boundary, and consists of a tungsten-bearing vein occurrence that is also in metamorphic rocks. The four sites within the study area consist of vein occurrences in metamorphic rocks that contain silver, gold, arsenic, lead, zinc, and copper. The veins at these four sites are too small and low grade to be classified resources; however, there are indications that three of the sites may have silver and gold resources at depth. Detailed delineation of the veins, and determinations of tonnages and grades are needed. This would entail additional mapping and sampling, trenching and drilling, and opening inaccessible workings.

Jan 1, 1987

By B Crowdey, J Wall

The particular underground operation relating to this paper is a gold producer and has an orebody predominately consisting of rhyolite and marcasites pyrite. The ore has been identified as being reactive to nitrates.Operations currently utilise two twin boom Tamrock™ Super-Drill Jumbos for development mining. Capital (waste) headings have a nominal size of 7 m wide × 6 m high, while ore headings are designed at 5 m wide × 5 m high, with the lower reaches of the mine narrowing down to a 4.5 m × 5 m design. Production drilling is currently undertaken with an Atlas-Copco L6 Solo. Due to the reactivity of the ore, inhibited emulsion phase bulk explosives are used for all blasting activities, with electronic detonators utilised in the production sequence.Sublevel shrinkage stoping is utilised when the orebody is stronger than the host rock. After blasting the ore, and during extraction, the surrounding host rock cannot maintain integrity and it ‘collapses’ on top of the ore. Gravity forces this collapsing rock to follow the blasted ore through the drawpoints.The highest risk involved with sublevel shrinkage stoping is the necessity for charge crews to work upon ‘rills’ at the drawpoints, which are occasionally unstable, to charge the next blast ring to be fired. To overcome this issue a loading technique called ‘precharging’ is used whereby two to three rings are charged, but only the first ring is fired. This technique can minimise risks by taking the charge crew away from the rill and brow.As this mine contains hot and reactive ground, strict guidelines from the Australian Explosives Industry and Safety Group Inc (AEISG) are adhered to. These guidelines relate to the sleep time for the precharged rings.This paper describes the issues faced with precharging in hot and reactive ground, the monitoring required and the systems and procedures that were put in place to enable a successful outcome.CITATION:Crowdey, B and Wall, J, 2014. Precharging sublevel shrinkage production rings in hot and reactive ground with electronic blasting systems, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 283–288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By C. H. Bloomster

This study estimated (1) radon and radon daughter emissions from underground uranium mines; (2) the reduction in radon that would be released to the surface by using control techniques such as bulkheads, sealants, backfilling, and positive pressure ventilation; (3) the cost for radon and radon daughter removal from total exhaust air; and (4) total radon and radon daughter discharge for lower occupational exposure limits. For 13 large underground uranium mines, estimated yearly radon emissions from each mine ranged from 900 to 3,400 Ci. The estimated age of air emitted from the mines ranged from 11 to 37 min. Potential radon removal methods for the total mine exhaust were evaluated. The cost of these methods was prohibitive. Diurnal and seasonal changes may affect radon emission over short periods of time, but do not affect the total emissions over the long run. Radon and radon daughter emissions would be little changed by increased ventilation requirements needed to achieve lower occupational exposure limits. The concentrations in the exhaust would be lower, but the total release would be the same

Jan 1, 1984