Search Documents

By Albert L. Toenges

EARLY in 1949, the Economic Cooperation Administration requested the Bureau of Mines to assign a coal-mining engineer to study milling conditions in Greek lignite mines; to make recommendations for the introduction of methods and practices that should increase production and decrease the cost of mining; and, from the results of a geological reconnaissance by geologists of the United States Geological Survey, to suggest plans for the development of mines to supply fuel for a thermal power plant, Albert L. Toenges was assigned to this investigation and arrived in Athens, Greece, March 15, 1949. The study of mining operations and the geological reconnaissance (which was made by W. G. Pierce and X. M. Denson, geologists, United States Geological Survey) Were conducted concurrently. The Geological Survey will publish the results of its investigation separately. Washability studies of lignites from Aliveri and Kimi were made at the Central Experiment Station of the Bureau of -Mines, Pittsburgh, Pa. The lignite fields mentioned in this bulletin are shown in figure 1.

Jan 1, 1951

By Timothy J. Orr, Robin J. Burgess-Limerick, Jennica L. Bellanca, MARGARET E. RYAN

Powered haulage continues to be a large safety concern for the mining industry, accounting for approximately 50%of the mining fatal accidents every year. Among these fatal accidents, haul-truck-related accidents are the most common, with 6 of 28 and 6 of 27 fatal accidents occurring in 2017 and 2018, respectively. To better understand why these accidents continue to occur and what can be done to prevent them, researchers reviewed the 91 haul-truck-related fatal accidents that occurred in the USA from 2005 to 2018 and performed bow-tie analyses using the final reports published by the Mine Safety and Health Administration. The analyses explore the context of the accidents with a focus on the initiating event, event outcome, hazards present, and possible preventative and mitigative controls. Overall, the vast majority of the accidents resulted in a haul truck colliding with the environment, and the majority of these events were initiated by loss of situational awareness or loss of control. The majority of the hazards were related to design and organizational controls. The results of this study suggest a need to investigate operator decision-making and organizational controls and to focus on improving design and operation controls such as mine design and operational procedures.

Feb 22, 2021

By S. F. Radtke

The properties and characteristics of lead and zinc have made these metals useful to man in many ways since the days of antiquity. Despite their long history of use, however, these metals have proved to be extremely resilient and responsive to modern needs. New alloys and compounds continue to be developed, adding to the growth of these metals. Consumption data is given for 1969 and compared with one and two decades ago. Trends in major markets also are cited and explained. Uses for lead and zinc which have come into prominence within the past few years are described and explained, with emphasis on the role played by the industry's cooperative research program. Current efforts in the research phase are discussed, with details given on major efforts for both metals, including new alloys, process developments, applications research, finishes, coating, paints and pigments, batteries and fundamental research. A forecast is given of promising new areas and a projection made on a longer term of new applications that may emerge from current research.

Jan 1, 1970

By Daniel M. Flanagan

"Editor’s note: Each year, Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue, all the while doing their own jobs. Thank you to the industrial minerals annual review editor, to the Industrial Minerals & Aggregates Division technical committee chair and vice chairs, and to the authors of the individual commodity profiles. Jim Norman, member SME, of Tetra Tech, is the industrial minerals annual review editor.Joe Garska, member SME, of Imerys, is chair of the Industrial Minerals &Aggregates Division’s Technical Committee.The technical committee vice chairs include:• Hyunjung Kim, member SME, of Chonbuk National University, agricultural materials.• Xihui Lin, member SME, of Kemira, ceramics and refractory materials.• Nikhil Gupta, member SME, of Virginia Tech, chemical raw materials.• Adam Rodriquez, member SME, of Penn State, construction aggregates.• LeDeana Roberts, member SME, of Imerys, fillers and pigments.• Harsha Kolla, member SME, of ChemEOR, sorbents, filters and process aids.• Edgar Blanco, member SME, of FLSmidth, specialty minerals.Their help makes possible this July industrial minerals issue. On behalf of ME readers, the editors thank them.During the past 25 years, U.S. ball clay production (the quantity sold or used by domestic producers) increased from 788 kt (869,000 st) in 1990 to an alltime high of 1.31 Mt (1.44 million st) in 2003 (Fig. 1). Housing construction within the United States, a leading market for ball clay-based ceramics and sanitaryware, began to decline in 2005, which resulted in a considerable decrease in sales of ball clay that continued through the 2008-2009 economic recession. After bottoming out at 831 kt (916,000 st) in 2009, ball clay production steadily increased through 2015 (Fig. 1). Estimated sales in 2015 were 36 percent higher than those in 1990 and 18 percent lower than those in 2003.Four companies (H.C. Spinks Clay Co., Imerys S.A., Old Hickory Clay Co., and Unimin Corp.), mined ball clay in five states during 2015. An estimated 1.7 Mt (1.18 million st) of ball clay valued at an estimated $47.5 million was sold or used by U.S. producers, a 4-percent increase from 1.03 Mt (1.14 million st) valued at $45.2 million in 2014. Approximately 65 percent of total ball clay production was air-float, 25 percent was crude or shredded and 10 percent was water-slurried"

Jul 1, 2016

For its Hellyer project, Aberfoyle sought to establish a high degree of confidence in all aspects of the feasibility study. Accurate capital and operating cost estimates were an integral and essential part of the study. They were crucial to the evaluation of investment returns and competitive cost position. Both the capital and operating cost estimates were based on the comprehensive data available from exploratory mine development, pilot plant operation, detailed engineering design, and Aberfoyle's experience in the area. One of the principal project objectives was to maximise operating productivity and efficiencies and this created capital cost alternatives which needed thorough cost-benefit assessment. The estimated capital cost for construction and development was $90 million, and the project was completed virtually on time for $80 million. The first year's experience indicated that operating costs would settle to well within 10% of the estimates.

Jan 1, 1990

By M Berry, F MacCorquodale

The ownership, management and employment structures operating in the Australian minerals industry have dynamically evolved during the last 30 years. One of the most dramatic changes, from an exploration and mining geology perspective, is the reduction of in-house geological expertise and an ever increasing reliance on contract and consulting services.For all companies - big and small - two key issues resulting from these changes are the management of core geological intellectual property (IP) and competitive advantage. This is because there are less experienced geologists at exploration and mine sites, there are fewer head-office technical service teams to support mine sites, exploration teams are smaller with less specialists employed, and there is an ever-greater dependence on contract and consulting services.This paper reviews and explores these issues with an industry-wide geological context, then provides a case study of how Newcrest Mining Limited (Newcrest) has dealt with these issues in exploration. Newcrest has grown from a one-mine company with an Australian exploration focus, to a large global company with multiple operations and an extensive international exploration portfolio. NewcrestÆs management of its geological IP and competitive advantage has evolved as the company has grown and responded to market conditions, including its internal restructuring in mid-2013.CITATION:Berry, M and MacCorquodale, F, 2013. Managing geological intellectual property and competitive advantage - Newcrest Mining LimitedÆs experience, in Proceedings World Gold 2013 , pp 37-44 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

This field guide is designed for use in planning pollution control and reclamation activities on small sand and gravel operations. Its purpose is to assist operators in selecting environmentally desirable pollution control and reclamation procedures based upon their particular mining situation. The guide includes information on interpreting physical and cultural factors that must be considered in planning and implementing a mining and reclamation program, achieving environmental protection objectives, and improving community/industry cooperation. Included as appendices are a summary of state laws and a list of additional readings on the subject.

Jan 1, 1981

By D. E. Andrews

The objective of this study was to investigate the environmental effects of slaking of surface mine spoils. To accomplish this, both field and laboratory programs were undertaken, supplemented by a thorough literature search. The field program consisted of drilling the highwall as well as test pitting in recent, two-, five, and ten- year-old spoil piles at four active mining sites in the eastern bituminous coal fields. Pertinent observations were made and samples collected for laboratory analyses which consisted of several standard geotechnical, agronomic, and geochemical tests. Durability tests utilized included jar slake, cyclic wet-dry, rate of slake, and slake durability tests. Correlation between field and laboratory portions was made- and results presented. The report is concluded with a discussion of the slaking process and associated environmental impacts, proposal of a preliminary classification system for use in premine planning, and presentation of management techniques to optimize the slaking process.

Jan 1, 1980

The first metal-mine accident-prevention course was prepared and published in 1942-45 as a series of seven miners' circulars (Nos. 51-57). The scope of the course has been broadened, revised, and brought up to date, and it is being published as a similar series of seven miners' circulars on accident prevention in metal and nonmetallic mines. These circulars are: 1. Accident Statistics (Miners' Circular 51), dealing with general statistics on accidents and injuries at metal and nonmetallic mines, including causes, costs, and the uses of investigations and reports of all accidents.

Jan 1, 1957

By B. R. Boardman

Project Environmental Approval is a multi-faceted issue. From a mining perspective, it is a costly item because of avoidable time delay. The government perspective is that the approvals are a necessary part of meeting departmental requirements to ensure that the wellbeing of other uses of the environment is maintained. This paper outlines some of the problems inherent in the environmental approvals process and makes recommendations to both the proponent and government about improving the efficiency of the process.

Jan 1, 1978

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSB systems are safer than conventional shaft sinking. The potential risk of conventional shaft Sinking operations could be reduced by over 30%, on the average with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include a better fire suppression system, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981

By Zhang Chuanfu

Keywords: solid solution, Ni-Co alloy powders, thermal decomposition, fibres. Synthesis of fibrous Ni-Co alloy powders was achieved by thermal decomposition of precursor of complex Ni-Co oxalates solid solutions obtained via modified coprecipitation method among intimate mixing solution of NiCl2?6H2O , CoCl2?6H2O and H2C2O4?2H2O in the presence of surfactant polyvinylpyrrolidone (PVP) and organic solvent ethanol. Scan electron microscopy (SEM), X-ray diffraction (XRD), X-Ray photoelectron spectroscopy (XPS), disperse energy X-ray analyses (EDX) were used to characterize the structure features and chemical compositions of the as-prepared fibres. The influences of decomposition conditions, including temperature, time, the flow rate of N2+H2, and the heating rate, on the morphology, average size and specific surface area of the Ni-Co alloy powders were investigated. It is found that a trend of the mutual alloying of nickel and cobalt: the formation of perfect solid solution for any compositions NixCo100-x was indicated and corresponding NixCo100-x alloys with fcc phase can be obtained under the optimal conditions.

Jan 1, 2005

By C. C. Clark, D. J. Benton, J. B. Seymour, L. A. Martin

"The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting research on jackleg use and related accidents in underground metal mines. This paper provides an analysis and overview of jackleg drill usage, accidents, operational characteristics and alternatives, based on information from injury reports, legacy research, stakeholder input and published literature. The results indicate that jackleg drills are involved in more groundfall accidents in underground metal mines than any other drill, and jackleg-drill-related injuries are most prevalent at the face in the course of installing initial ground support. Practical mechanized alternatives to jackleg drills for drilling and bolting under incomplete support in narrow underground openings have not yet been realized. Small, versatile mechanized bolting equipment needs to be developed to address jackleg-drill-related accidents and improve safety at mines where jackleg drills are being used. IntroductionJackleg drill is a generic name for a handheld, rotary, percussion rock drill equipped with an attached reaction leg to provide stability and thrust (Fig. 1). All of the drill and leg controls are located near the operator’s handle at the rear of the head portion of the drill. Jackleg drills are classified according to the bore size of their pneumatic pistons, which normally range from 6.03 to 8.26 cm (2.375 to 3.25 in.) (Kurt, 1982; Clark, 2012). Jackleg drills typically weigh 46.7 kg (103 lb), but the weight can approach 54.4 kg (120 lb) after being fitted for operation with drill steel and air and water hoses (McKibbin and Clark, 2001). In underground mines, jackleg drills are commonly used to drill 3.8-cm (1.5-in.) diameter holes up to 1.83 m (6 ft) deep in rock."

Aug 1, 2016

By Wallace W. Key

Mineral raw materials produced in California, other States, and foreign countries were purchased for consumption in quantities valued at over $60 million at 800 of the 1,200 chemical plants operating in California Fn 1960, according to questionnaires completed by company officials. These and other data received from mineral consumers, producers, dealers, and Government agencies formed the basis for this the first of a series of reports designed to present the intricate features and relationships controlling mineral raw material supply and demand in California industries. The results of this study indicated certain changes in use patterns of minerals in chemical manufacturing; a shift in requirements from metals to nonmetals, from inorganics to organics, from natural to synthetic materials, and from distant to local sources of supply.

Jan 1, 1965

By Wallace W. Key

Mineral raw materials produced in California, other States, and foreign countries were purchased for consumption in quantities valued at over $60 million at 800 of the 1,200 chemical plants operating in California Fn 1960, according to questionnaires completed by company officials. These and other data received from mineral consumers, producers, dealers, and Government agencies formed the basis for this the first of a series of reports designed to present the intricate features and relationships controlling mineral raw material supply and demand in California industries. The results of this study indicated certain changes in use patterns of minerals in chemical manufacturing; a shift in requirements from metals to nonmetals, from inorganics to organics, from natural to synthetic materials, and from distant to local sources of supply.

Jan 1, 1965

By J. R. Goode

Up to one half of neodymium and praseodymium production, key ingredients in permanent magnets, is produced illegally. About 60% of cobalt production, critical in lithium-ion batteries and other applications, comes from central African states, and much of it is produced illegally. Tantalum, important in modern electronics, is also primarily sourced from central Africa and, again, much of it illegally. Illegal mineral production, as exemplified here, is often used to fund armed conflict. Furthermore, it is typically conducted with scant regard for human rights and environmental protection. It also leads to depressed prices which in turn limits the possibility of legitimate producers entering the market. Systems of traceability and provenance, along with cooperative supply chain participants can limit the production of illegitimate material and thereby improve conditions in the countries of origin and reduce downward pressure on prices.

By Syd Peng, W. B. Guo, F. Du, L. Yang, J. Yw. Cheng

The annual ICGCM China was initiated in 2014. Up to 2023, ICGCM China has been held 9 times. In the 9 conferences during the past 10 years, about 559 papers in 17 topical areas were presented and attendance ranged from 200+ to 400+ each conference. The 42nd ICGCM China was held in Xiangtan, Hunan, China, 10/20–10/22/2023. There were 86 papers presented in 26 topical areas. In addition, an MS and PhD Research Forum was held concurrently with 36 papers presented by MS and PhD candidates in mining engineering from 8 schools. The conference plays an important role in cultivating advanced degree student talents. In this paper, all 559 papers reviewed previously were summarized. In addition, the 42nd ICGCM China is used to illustrate the current and future development trends of coal mine ground control in China. It summarizes the 122 papers (including 36 MS and PhD forum papers) grouping into, and in terms of, 26 topical areas. In addition, its unique and innovative subject areas, short summary of developments as well as conference strengths and shortcomings will also be presented.

Jun 25, 2024

By J. A. Cooper

The objectives of this research were to define the chemical composition and physical characteristics of the aerosols associated with attached radon daughters in operating uranium mines, and to investigate the relationship between these aerosol parameters and operating conditions. Major Results and Conclusions The organic, inorganic and radiological characteristics of test chamber and active U-mine aerosols have been measured as a function of particle size. These measurements represent the first detailed analyses of the organic and inorganic components in U-mine aerosols and the first determinations of the details of the individual and total radon daughter distributions in operating U-mines. The following is a list of the major results and conclusions:

Jan 1, 2012

By Sandeep K. Sharma

The U.S. Bureau of Mines has been investigating new techniques to improve the of mineral to recover water lost in the waste slurry, and to produce dewatered solid dewatering s suitable for disposal. As part of this investigation, a study was undertaken to investigate the feasibility of dewatering Alaska placer effluent. Based on the laboratory tests, preliminary field tests were conducted on three placer mines in Alaska. At these mines, the water recovered from the placer effluent (250 to 23,000 NTU) exhibited turbidities of 20 to 240 NTU. In the second year of the project, a large-scale dewatering unit was set up at a mine located in the Livengood district. The feed, at flow rates up to 935 gpm, was mixed with dilute PEO solution in a flexible plastic hose with and without static mixers. Feed to the dewatering unit generally ranged between 300 and 26,500 NTU and required PEO dosages of 0.02 to 0.14 lb per 1,000 gal to produce water from the screen underflow with turbidities of 20 to 50 NTU. During this period, a small unit was also operated at Dow rams of 10 to 25 gpm at sewn sites throughout Alaska, with the effluent from four of the sites being dewatered successfully.

Jan 1, 2010

By W. R. Herrera

A research effort was conducted to present or develop methodology for evaluating candidate potting materials intended for use in explosion-proof enclosures. The primary purpose was to develop acceptance guidelines based on arc decomposition products. Acceptance criteria can be based on: ? Inherent thermo-chemophysical, mechanical and electrical properties; ? Arc decomposition products: ? Nature of volatile products produced, e.g., flammability, explosivity, synergistic effects on existing environment in the enclosure, toxicity; ? Quantity produced as a function of arc power and duration; ? Acceleration aging tests to evaluate breakdown under electrical stress.

Jan 1, 1982