Search Documents

By K. H. Heino

Two 200 T/da Lurgi Turbulent Layer fluid-bed roasters have been in operation at Canadian Electrolytic Zinc Limited since 1966. Zinc concentrate containing 52-54% Zn, 9-11% Fe,31-33% S is treated to produce calcine containing 60-62% Zn,10-12% Fe, .l-.3% S as sulphide and .8-1.2% S as sulphate. Each roaster train comprises a waste heat boiler, two cyclones in parallel and a two-field electrostatic precipitator. Distribution of calcine collected is 10-15 percent from bed overflow, 55-65 percent from boilers, 20-25 percent from cyclones and 2-6 percent from precipitators. A Monsanto designed contact plant produces acid at a rated capacity of 365 T/da (100% H2304 basis) from roaster gases diluted to 7.0-7.5% S02. The process steps are gas cleaning and cooling by weak acid scrubbing, acid mist removal in electrostatic precipitators, gas drying in 93.5-96.5% H2304, conversion of sulphur dioxide to sulphur trioxide in a four-pass converter containing vanadium pentoxide catalyst, and absorption of the sulphur trioxide in 98.1-98.3% H2S04. Product acid is 93.2% H2S04. Conversion efficiency is 97-98 percent and overall sulphur recovery from concentrate is 87-90 percent. The adjacent fertilizer plant has a capacity of 135 T/da of P205. The products are 54 percent phosphoric acid, run-of-pile triple superphosphate, and diammonium phosphate. The plant is of Ugine-Kuhlman design and consists of an air-cooled multiple tank reactor, a tilting pan filter, and a forced circultation vacuum evaporator. Triple superphosphate is made on a continuous belt and partially cured in a rotary dryer. Diammonium phosphate is produced by ammoniating phosphoric acid in a single stage reactor. The slurry of ammonium phosphate is granulated in a blunger and dried.

Jan 1, 1970

By W. S. Landers

This bulletin is a detailed study of low-temperature, entrained-bed carbonization of a Texas lignite. The lignite studied was from the Sandow strip mine and is representative of the Rockdale formation of the Wilcox formational group. Carbonization was conducted in a continuous entrained-bed reactor at several temperatures in the 8801 to 1,52°C F range, and at air-coal ratios it the 0 to 10.30 scf/lb range (moisture- and ash-free basis). Carbonization rates ranged from 97.1 to 410.0 lb/hr (as-received basis), At the higher air-to-coal ratios employed, all or most of the carbonization heat was provided by internal combustion with air in the reactor. At the lower air-to-coal ratios, parts of the heat for carbonization was supplied externally. It was demonstrated that the entrained-bed carbonization of lignite is a complex reaction and that several variables, of which carbonization temperature, air-to-lignite ratio, and the average size of lignite are important, act together to influence both the carbonization yields and the properties of the resultant products, Process variables established by pant tests were used to design the industrial scale carbonizer operated at Rockdale, Texas, by the Texas Power & Light Company as agents for the Aluminum Company of America. Properties of the carbonization product obtained from the industrial scale reactor were essentially the same as those obtained from the pilot plant reactor operated under the same conditions.

Jan 1, 1968

During the last 125 years, the steel industry has witnessed revolutionary changes in the process of steelmaking. The Bessemer process was the predominant steel production technology during the last two decades of the 19th century. The open hearth process accounted for the lion's share of world steel production for six decades from 1910 to 1970. With the appearance of the LD process on the industrial stage in 1952, the importance of open hearth process declined and currently the basic oxygen processes are contributing more than 60 per cent of the world steel production. The LD process also led to the development of several other oxygen blown processes such as LDAC, OLP, OBM, QBOP, EOF, Clc.

Jan 1, 1999

By Yongsik Jeong, Kwangmin Kim

Most tailings storage facility (TSF) failures occur in active, upstream-type TSFs, often due to extreme and unexpected weather conditions—specifically, heavy rainfall and strong winds. This case study of a TSF in southern Arizona examines the use of the optimum safe beach distance (Doptimal, the optimum distance between the crest and decant pond) as a tool for monitoring geotechnical stability and reducing catastrophic failures. A digital model of the TSF was used to determine the critical beach distance (Dcritical) under normal weather conditions, and Doptimal was then determined by adding incremental distances to account for the effects of heavy rainfall (Drainfall) and strong winds (Dwind). To overcome accessibility issues, a drone was used to map the TSF geometry and create a digital model. This model served as the basis for conducting a coupled stress-seepage, finite-element (FEM) analysis with a safety factor of 2.0 to assess geotechnical stability (Dcritical). The safe beach distance increments were determined using the PMP (probable maximum precipitation) and possible maximum wind speed. Based on this analysis, the optimal safe beach distance at the study site was identified as 202.2 m. Since the current beach distance (371 m) exceeds this value, the TSF was considered to be stable and satisfied the design safety factor of 2.0. However, this distance should be reassessed periodically to account for changes in the TSF geometry and other conditions. Furthermore, it applies only TSFs that are well-managed and feature a smooth, non-undulating beach surface with a consistent slope.

By M Edwards

The paper outlines the successful application of some of the on-belt technologies available from Scantech International Pty Ltd and how these have provided benefits in a number of mining and mineral processing operations. Effective process control requires real time analysis so quality can be fed back to the previous process and fed forward to a subsequent process. A range of on-belt analysers that allows for full stream, continuous, non-contact analysis of conveyed materials is available to achieve this. Real time results can provide timely information for effective process control. Benefits of on-belt analysis systems become more evident once the true variability of material quality and moisture content in conveyed flows is measured. To obtain economies of scale in mineral processing operations large material flows are achieved using conveyors. The cost and effort to sample representatively increases as conveyor flows increase. One sample may represent a few tonnes or up to 10 000 tonnes of material. The turnaround time between sampling and availability of sample analysis data does not allow real time process control. Tonnage flow rate, moisture content and elemental or mineralogical composition are required to perform effective process control of most conveyed streams. Tonnages can be effectively measured using belt weighers. The analyses derived from small samples supplied by conveyor-based sampling systems contain high variability. On-belt, continuous analysers see all the material and, through short term compositing of analyses, supply less variable results. Real time analysis helps operators develop a better understanding of material variability. Analysers can be effectively utilised to improve the consistency of product quality through bulk sorting and blending control. Many existing users of the technologies have gained competitive advantages through their ability to supply a more consistent quality product to the market.

Jan 1, 2008

By Karl J. C. Harries

13.1. RIGHT TO RECEIVE ROYALTY CONTRACTUAL ONLY1

Jan 1, 2003

By Dolly Chakraborty, S. Ranganathan, S. N. Sinha

Pre-reduction of chromite outside the submerged-arc furnace (SAF) can significantly lower the specific power consumption in the SAF process. Conventional processes for the pre-reduction of the ore operate at relatively high temperatures, at 1400-1500°C. It is possible to enhance the rate of reduction at low temperatures by optimizing the flow rate of inert gas over the reaction site. The influence of the flow rate of inert gas on the rate of reduction of chromite ore was investigated. The rate of reduction initially decreased wit the flow rate of the gas. It increased subsequently at higher flow rates to be followed by a decrease again. There was an optimum flow rate at which maximum reduction could be obtained. It was possible to achieve high levels of reduction at 1200°C by optimising the flow rate of the gas. The degree of reduction obtained was comparable to that obtained at 1400-1500°C, by conventional process routes.

Jan 1, 2007

By S Zheng, Y Zhang, Z Wen, S Ma

Red mud (RM) is a solid waste product generated during alumina refinery process, and is usually stored in SFs (SFs) because it canÆt be disposed of easily. In this paper, environment degradation caused by RM-SFs was systematically assessed by the method of single factor pollution index based on the analysis data of water, soil and atmosphere sampled around one newly-built and one decommissioned RM-SFs, which are managed by an alumina production company in China. The results revealed that the ambient environment around RM-SFs is seriously polluted by alkali and mercury (Hg). The pH value of RM leachate, surrounding surface water and groundwater are all higher than the limit of water quality standards in China. And as a possible result of overflowing of high alkaline leachate, soil pH value for the decommissioned SF decreases with increasing distance between the sample collection points and the closest side of RM storage facility (RM-SF). Total Hg concentrations in RM leachate, surrounding surface water and groundwater all exceed Grade III limits of ChinaÆs Environment Quality Standards for Surface Water and Groundwater. However, the air quality was little affected as the daily average of TSP in the air is below grade II values of Chinese Ambient Air Quality Standard.CITATION :Wen, Z, Ma, S, Zheng, S and Zhang, Y, 2012. Assessment of environmental quality impacts caused by red mud storage facilities in China, in Proceedings Life-of-Mine 2012, pp 51-58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By G. Graves, J. A. Walker

"Abstract - The Mount Fronsac North volcanogenic massive sulfide deposit is the most recently discovered massive sulfide body in the Bathurst Mining Camp. The deposit occurs within a sequence of intercalated fine-grained felsic tuff and sedimentary rocks (Little Falls member), at the top of the Nepisiguit Falls Formation. Aphyric to sparsely feldspar-phyric rhyolite and related volcanic rocks of the Flat Landing Brook Formation overlie the host sequence. The massive and semimassive parts of the deposit have a north-south strike length of 525 m and a dip of ~45°E; the deposit is continuous downdip for 600 m, and thickness varies from 2 to 20 m. The deposit contains an estimated geologic resource of 14 Mt of low-grade, semimassive (>60%) to locally massive sulfides, and includes a high-grade zone of 1.26 Mt grading 7.65% Zn, 2.18% Pb, 0.14% Cu, 40.3 g/t Ag, and 0.40 g/t Au. The semimassive to massive sulfide intersections occur in an envelope of quartz-sericite±chlorite schist, which is interpreted to be intensely deformed felsic tuff. This sequence has a maximum thickness of 140 m and contains significant (up to 50%) fine- to coarse-grained disseminated pyrite. The pyritic envelope has a strike length of 900 m and extends over 1000 m downdip. Massive sulfides are found throughout this alteration envelope, but more commonly occur at or near the upper contact. The significance of the discovery of this deposit is that it represents a near surface discovery of a large tonnage sulfide body in a mature mining camp, one in which the possibility of discovery of a new shallow deposit had been all but discounted. This opens the possibility for future discoveries in this part of the Bathurst Mining Camp. Sommaire - Le gîte de sulfures massifs volcanogènes du Mont Fronsac Nord est la découverte de sulfures massifs la plus récente dans le Camp Minier de Bathurst. Le gisement est situé dans une séquence de tufs felsiques à grains fins interlités de roches sédimentaires (membre de Little Falls, au sommet de la Formation de Nepisiguit Falls. La partie massive et la semimassive s’étendent du nord au sud sur 525 m et ont un pendage de ~45°E; le gisement est continu sur 600 m en angle de chute et son épaisseur varie de 2 à 20 m. Le gisement contient une ressource géologique évaluée à 14 Mt de sulfures semimassifs (>60%) localement massifs à basse teneur, incluant une zone à haute teneur de 1.26 Mt titrant 7.65% Zn, 2.18% Pb, 0.14% Cu, 40.3 g/t Ag, et 0.40 g/t Au. Les intersections de sulfures semimassifs à massifs se situent dans une enveloppe de schiste à quartz-sericite ± chlorite interprétée comme un tuf felsique intensément déformé. Cette séquence contient une quantité importante (jusqu’à 50%) de pyrite disséminée dont le grain varie de fin à grossier et son épaisseur maximale est de 140 m. L’enveloppe pyriteuse s’étend latéralement sur 900 m et a été tracée jusqu’à 1000 m en angle de chute. Des sulfures massifs sont trouvés partout à l’intérieur de cette enveloppe d’altération, mais ils sont plus fréquents près du contact supérieur. L’importance de cette découverte tient à ce qu’elle est un exemple d’un gisement à fort tonnage nouvellement découvert à une faible profondeur dans un camp minier mature, i.e., un camp ou l’on ne croyait plus qu’il était possible de trouver un gisement près de la surface. Ceci ouvre la porte à la possibilité d’autres découvertes dans cette partie du Camp Minier de Bathurst."

Jan 1, 2006

By James Westfield

Drilling for roof bolting has created a new dust problem for the coal-mining industry. Drilling is inherently dusty, and control of dust produced by drilling vertical or nearly vertical holes is much more difficult than control of that produced by drilling flat or down holes.4/ Also, the dust produced by roof drilling differs in composition from that produced by drill-fur, or cutting the coal face because it contains a significantly greater amount of free silica and therefore presents a greater potential hazard of silicosis. Roof bolting has been practiced successfully in the mines of the St. Joseph Lead Co. in southeastern Missouri for over 20 years, but it was not until 1947 and 1948 that large-scale roof-bolting experiments were conducted in coal mines.5/ Although the need for dust control in conjunction with roof drilling was recognized from the beginning, the development and acceptance of roof bolting progressed so rapidly during 1949 and 1950 that solution of the dust problem lagged behind other engineering phases of the technique.

Jan 1, 1951

By S. J. Dai

The cadmium and cyanide are main poisonous components in cyanide electroplating cadmium waste water of an electroplating plant in Shenyang. The content of cadmium is about 26 mg/L and the content of cyanide is about 11.782 mg/L in this waste water. The main form of cadmium and cyanide are ions which are Cd2+and CN?. Because the cadmium and cyanide exceeded the standard seriously, the waste water must be disposed before it discharges. The microbiological method of treating heavy metals in wastewater has many advantages. For example, it has a fast adsorption velocity, high processing efficiency, wide range of pH and temperature, few invest, low running cost, no the second pollution and so on. At the same time, the CN? could be degradated by some microbiology. The physical nature, the chemical nature of Bacillus mucilaginosus, the adsorbing condition and adsorbing regular of Bacillus mucilaginosus to cadmium in the wastewater are studied by using Bacillus mucilaginosus as adsorbent removing cadmium from electroplating wastewater. The experimental results show that the adsorbing rate of cadmium is over 92%, under the room temperature(about 25?), stiring revolution in adsorption being 800 r/min for 30 min, pH being 5 , the bacteria being cultured after 5d with the biomass of Bacillus mucilaginosus 40g/L (wet weight). The mechanism in biosorption process of Bacillus mucilaginosus to cadmium is analyzed and discussed by TEM , Zeta potential,and infrared spectroscopy analysis. The results showed, the chemical involving is main adsorbing form, while electrostatic attraction, ions exchange, hydrogen bonding and Van Der Waals force are concerned cooperatively. ?NH2 ?, ?C=O?, ?C=O?NH?CH2, ?CH3, ?OH are main adsorbing groups. At the same time, the floatablity of removing cyanide by Bacillus mucilaginosus is explored.

Jan 1, 2014

By Gordan Marrs, O. Matwijenko

"The Kidd Creek metallurgical site has been highly integrated to maximize revenues from its base metals mines. The site's operations include a Concentrator processing 4.3 million tonnes per year of copper-zinc ore, a Copper complex producing 100,000 tonnes per year copper cathode and a Zinc Plant producing 130,000 tonnes per year of zinc metal. To improve operating efficiency with increasing emphasis on productivity, process control, process automation and process optimization have been augmented and expanded during the last decade.New microprocessor based control systems provided the opportunity for the capturing of an expanded number of process related measurements. As supervisory computers were already in place, databases could be generated with only increased disc space and database management programs required. Once the data had been accumulated and stored, a method was then required for handling, screening and sorting large volumes of information in relatively quick and easy terms in order that the stored information could be used. By 1984, a decision to use personal computers for accounting, engineering and management reporting provided the vehicle necessary to handle this data. Using commercially available software, large volumes of stored process data can be downloaded from existing databases, filtered, sorted, analyzed, graphed, displayed, projected, reported and distributed. All this can be performed in very little time."

Jan 1, 1989

By T. B. Colman

Paper presented at the MEP '89 conference held in Madrid, 13-15 November 1989. Britain has sustained an important metalliferous mining industry over many centuries. Recently, new geological concepts and exploration techniques have indicated that there is considerable potential for the discovery of a variety of deposit styles, often in previously neglected areas. The recent discoveries at Aberfeldy (Ba-Zn-Pb), Gairloch (Cu-Zn) and Cononish (Au-Ag)in Scotland and Curraghinalt (Au-Ag) and Lack (Au-Ag-Pb) in Northern Ireland are illustrations of this potential. Some of the prospective areas for future exploration are described and an indication is given of the legislative framework within which mineral exploration and development are carried out

Jan 1, 1991

By Samuel B. Christy

At the last meeting of the Institute, several contributions were made to the subject of miners' aid funds. Such matters will always form important factors in the administration of large industrial enterprises. From the frequently remote and isolated position of mining properties, it is a subject that often forces itself upon the attention of the mining engineer. Local conditions are usually so variable that no single method can be found equally well adapted to all localities. At the same time, a study of different types is often suggestive and valuable, and it is with this in view that these notes are presented. The Miners' Fund of New Almaden is a remarkably successful example of what may be done for miners by a wise and at the same time firm management, by simply directing their own efforts and without incurring any great expense to the stockholders,—a practical consideration not without importance in most cases. The quicksilver mines of New Almaden are situated at a distance

Jan 1, 1885

By William S. Miska

The study is an economic evaluation of historical, current, and projected refractory uses in the iron and steel industry of the United States. The first part of the report presents a refractories classification and identifies principal trends in the refractories industry; such as, value and volume of shipments, prices of finished refractory products, the number of manufacturers and plants for refractories production and marketing. The main part of the report treats refractory use patterns and technologic developments affecting refractories usage in the iron and steel industry. Changes in use patterns in each furnace type, refractory, and installation costs and the future outlook for refractories in ironrnaking and steelmaking are covered. The last part of the report identifies the principal raw materials used in refractories production and treats trends in refractory raw material consumption. An appendix to the report contains historical time series graphs of shipments of refractory types used primarily by the iron and steel industry and principal refractory raw materials sold or used by producers. An equation of the line of best fit was calculated from the earliest to the latest year in each time series, usually 1950 to 1965; these were extrapolated in order to derive volume estimates for the year 1975.

Jan 1, 1968

By Russell R. Trengove

In order to extend or delimit the known ore reserves adjacent to the Comet Coalition property on the western slope of the Highland Peak Range about 8 airline miles west of Pioche, Nev., the Bureau of Mines undertook an exploration project of diamond drilling. Production figures from this property, formerly known as the Schodde, are not available, but it has been reported that small amounts of rich silver and gold ore were Shipped by wagon to a smelter in the Salt Lake valley during 1900-1910. Small shipments were reported for the period 1915-1927, also. A study of the Pioche District by the Federal Geological Survey in 1942 and 1943 was the basis for the exploration program of the Bureau of Mines in 1947 This program consisted of diamond-drilling three holes. The total footage was 2,967 feet. No. 1 hole was drilled 1,260 feet, a record depth for diamond drilling in the Pioche District. Silver-bearing lead-zinc sulfide ores are found in the Combined Metals limestone, known locally as the C.M. bed, These deposits have been formed by replacement of the limestone that is inclosed in the Pioche shale.

Jan 1, 1949

By Davies S. G, Mackey L. C

The oxidation of iron and nickel sulphide concentrates, and the dominant sulphide minerals which comprise them, has been studied under ignition conditions using thermogravimetry (fG). The concentrates were derived from various minesites and they showed differing tendencies to ignite. Ignition temperatures ranged from 416 to 488°C and the extents of reaction, measured at 500°C, varied from 64 to 88 percent. The reactivity of the least reactivematerial was improved significantly by grinding. Particles <63/lm showed 85 percent oxidation compared with 55 - 65 percent for particles >63/lm.Examination of the individual sulphide minerals revealed that these materials also have significantly different degrees ofreactivity and are subject to particle size effects. For particles <45/lm, the ignition temperatures were as follows:ò pyrite and violarite 380 - 385°C; pentlandite 425 - 430°C; and pyrrhotite 470 - 475°;ò for particles >90 /lm, the ignition values were: pyrite 395 - 400°C;ò violarite 430 - 435°C; pyrrhotite 540 - 545°C; and pentlandite 560 - 565°C.Using the data on the individual minerals it was possible to rationalise the differing degrees of reactivity of the concentrates. The role of the most reactive constituent in initiating the ignition reaction has also been discussed.Finally, the results of this work were found to compare. favourably with the behaviour ofthe concentrates in industrial and pilot-scale flash smelters.

Jan 1, 1989

By Ralph M. Foecking

The disposal of the phosphate slimes produced by Florida beneficiation operations is perhaps the biggest single problem of the phosphate mining industry. This is an old problem which has not been solved and which is becoming increasingly severe. In a typical phosphate mining operation, the phosphate rock mined is initmately mixed with sand and clay, constituting what is known as matrix. During the beneficiation, the clay and other fine materials are separated usually at -150 mesh, and washed from the phosphate rock in a form of diluted slurry known as phosphate slimes. The quantity of slimes solids and their composition vary considerably with the location but usually represent from 25 to 35% of the ore mined. Because of the affinity that clays have for water, large volumes of water are required to separate the granular material in the matrix forming a dilute slime suspension (1.5 to 3% solids) of colloidal material, which settles very slowly, and thus requires immense impounding areas, which never becomes totally usable land. These ponds also contain about 25 to 35% of the total P205 values mined. The magnitude of the problem represented by the slimes can be appreciated better if we realize that there are around

Jan 1, 1971

By Ron Light, Doug Applett

"HistoryThe Nanisivik mine began operation in October 1976 as the world's most northerly metal mine and the first permanent industrial project in the Canadian High Arctic. Located 700 km north of the Arctic Circle on Baffin Island's Strathcona Sound, exploration by Texasgulf Inc. between 1957 and 1970 had outlined the ore deposit. In 1974, Nanisivik Mines Ltd. was formed with Mineral Resources International, the Government of Canada, Metallgesellschaft and Billiton being shareholders, and Strathcona Mineral Services Ltd. providing project management. In 1996, Breakwater Resources purchased the mine from Alberta Energy Corporation Limited which had recently acquired the assets of then owners Conwest Exploration Ltd.Ore DepositThe main ore deposit is very flat, approximately 80 m in width and varying in thickness from 3 m to 16 m. The length of the deposit is approximately 3000 m with satellite zones located on the perimeter of the main zone. The economic mineralization is sphalerite with minor galena and silver. The sphalerite and galena are coarse grained and associated with pyrite as the main gangue component with minor inclusions pf dolomite and calcite within the deposit. The deposit being hosted in a permafi·ost environment creates a number of challenges. Dry drilling is employed in room and pillar production drilling. The permafrost aids in the stability of both the pillars and the back."

Jan 1, 2000

By Braam Blom

PK2 Ventilation shaft is part of Paardekraal No 2 twin shaft system that is being developed to replace depleting Merensky reef production at Paardekraal shaft complex. The sinking team at this shaft faced considerable challenge of improving the total sinking cycle in order to be able to deliver the fully equipped shaft on time and on schedule. The cladding support cycle was identified as the tedious and time consuming activity in the overall shaft sinking operation. Reduction in the time required for handling and setting up the support installation equipment, and the time required for subsequent installation of the necessary support has a direct impact on the overall cycle time, and consequently the overall productivity and efficiency of the sinking operation. This reduction in support cycle was achieved by making use of machine carousel. The objective of this paper is to describe the support methodology that was used during the ventilation shaft sinking and the use of the machine carousel to reduce the cladding support cycle. The machine carousel replaces the traditional use of machine kibble in conventional vertical shaft sinking and has been designed specifically for installation of sidewall support at the shaft bottom during the sinking process.

Jan 1, 2009