Search Documents

By Francis Foley

IN examining steel under the microscope, one is constantly confronted with structures that are difficult to interpret. Recently, in a collection of samples for exhibition purposes, the writer found apiece of open-hearth runner metal, 2 in. (50 mm.) in diameter, that had been fractured for use as a sample of cast-steel structure. On polishing and etching a section for the purpose of photographing a field to typify the microstructure of steel in the "as cast" condition, a variety of structures was found (Fig. 1) so arranged as to arouse interest at once. For a distance of about 0.065 in. (1.6 mm.) from the skin of the runner, normal ingot structure was found (Fig. 2); this was followed by a zone, about 0.215 in. (5.5 mm.) wide, of considerably lower carbon content in which occurred a most pronounced Widmannstättian structure (Fig. 3); from this point on to the center of the runner, the metal was again of normal ingot structure (Fig. 4). Representative samples taken from the metal in the three zones showed the following analysis: C Ni Cr Metal from skin 0.34 1.26 0.63 Widmannstättian zone 0.21 1.18 0.63 Metal from center 0.34 1.32 0.67

Jan 7, 1919

By F. N. Kissell

U.A. Mine Safety and Health Administration (MSHA) coal dust compliance data sometimes shows high silica levels at roof bolters. However, it is unclear whether this silica normally originates from the bolter itself or from other dust sources upwind of the bolter research studies to answer this question at individual mines have been conducted. However, operational practices vary from mine to mine thus, the information gleaned from any one study cannot be accurately extrapolated to describe silica dust sources in most mines. In this paper, three decades of bolter dust research are reviewed the results showed that, while inadequate maintenance on the bolter dust collection system can result in excessive dust, more likely reasons for high silica levels are inadequate ventilation of the mine entries being bolted and dust traveling downwind from the continuous miner to the bolter. Scrubbers on continuous miners may not be removing as much silica dust as expected. Mining Engineering, 2011, Vol. 63, No. 10, pp. 78-82. Official publication of the Society for Mining, Metallurgy and exploration, Inc.

Jan 1, 2011

By J. B. Zadra

Much has been published by various investigators on the use of activated carbon for adsorbing precious metals from cyanide solution and pulp. For the benefit of the reader, a list of these earlier publications appears at the end of this report. The present paper deals only with a process for extracting gold from gold-laden carbon and re-use of the de-adsorbed carbon. At the Getchell mine, Redhouse, Nev., experiments have been in progress for several years concerning the use of activated carbon to adsorb gold from their slime circuit pulp. The experimental work has been successful. Their practice has been to ship the gold-laden carbon to a smelter for treatment, which meant the total loss of the carbon in addition to smelter and freight, charges, all of which proved costly and wasteful.

Jan 1, 1950

By Harvey Parker

This is part two of an article on the prominent role that the United States and its industry leaders have played on the International Tunnelling and Underground Space Association (ITA), which represents the underground construction and underground space industries worldwide. The U.S. is officially represented in ITA by UCA of SME. (Part one is in T&UC, June 2007, pp 39-42) Tunnel advances in 1960s and 1970s The 1960s and 1970s were active and productive times for the U.S. tunneling industry. During that time, federal programs, sponsored by the Federal Railroad Administration (FRA), the Office of High Speed Ground Transportation (OHSGT) and the Advanced Research Projects Administration (ARPA), stimulated tunnel research and development. Also, the American Society of Civil Engineers (ASCE) and SME collaborated to create the Underground Construction Research Council (UCRC) and the Rapid Excavation and Tunneling Conference (RETC) series.

Jan 1, 2007

By W. David Tyler

Any mining or engineering-construction excavation that extends below the water table must be dewatered. In many situations, the ground is of low permeability or the workings extend only a short distance below the water table. So water removal can be handled easily and economically by using mobile centrifugal pumps. However, there is an increasing number of mines that have a continuous high flow of water into the workings. Controlling this flow can significantly increase the cost of ore production. Successful implementation of any major dewatering scheme will ultimately rely on a clear understanding of the local geology. This understanding is necessary before an interpretation of ground water conditions can be made. It will dictate which dewatering methods are feasible. Once the geology and the ground water system are known, the scope and timing of the dewatering measures can be varied with the mine plan. Ground water modeling can assist in optimizing the dewatering system, though the precise objective of each model should be clearly defined. Production wells must be sited and drilled so that individual well efficiencies are high. Any lost efficiencies will translate into higher operating costs. Each well must be designed for maximum long-term control of the water table, and pumps sized to operate under continually changing heads. Finally, the investment in each production well must be protected during the mining process.

Jan 1, 1991

This report summarizes the work performed and results achieved on the above contract from October 18, 1971 through July 14, 1972 under Phase II, Task 1: Detailed Design of Prototype and Task 3: Supporting Experimental Investigation. Operation and Service Manuals resulting from Task 3 are submitted under separate cover as are detailed design drawings and specifications, prepared under Task 1. Both items accompany this report. This report also includes (A) an estimate of the cost of construction, (B) a description covering the use of the equipment, and (C) a proposed test plan to demonstrate performance of the equipment in both the laboratory and a mine.

Jan 1, 1972

By Joseph J. Zaluski, J. Steven Gardner, Marco M. Rajkovich

The telephone rings at 3:20 a.m. An exasperated voice on the other end says, “There has been a mine explosion at Mine No. 5 and we have not heard from three units of men.” Twenty-three minutes later, the phone rings again and another panicked voice says, “There is something wrong at the slurry impoundment, the pool level has just dropped five feet and we are trying to figure out what is wrong” Thirty minutes later, the mobile phone rings. An excited security guard says, “We have reports of thick black water running down the right fork and left fork of Straight Creek and both seem to be rising in the banks.” If this is not enough excitement, the mobile phone rings again. A stressed company official says, “I just heard a report that black slurry is running out of the portals of XYZ Co. No. 2 Mine, which is adjacent to our No. 5 Mine.” Is this all some kind of dream or nightmare? More importantly, though, if this happens, what do you do? Most people think: “It can’t happen to me.” But mine explosions do happen, slurry impoundments can rupture and creeks can flood with black water causing damage to others, including competitors. A mine’s response must be quick, cool-headed, calculated and effective. This article examines the issues, concerns and ramifications of this hypothetical disaster. The authors then present a systematic crisis-management response.

Jan 1, 2004

"In the conceptual stages of engineering, benchmarking and empirical ratios are commonly the only references for estimating the production rate of greenfield projects. For underground mining projects, the lack of similar cases often makes the comparison difficult due to each project’s unique geology, rock quality or other singular characteristic. This paper discusses an analytical alternative for determining the maximum achievable production rate for underground stoping mining by modeling production as a continuous process. The results show that long-term maximum capacity depends exclusively on the achievable development rate and the development intensity of the design. In operations constrained by backfill, the development rate could be limited by the backfilling rate. Extraction rate and stope size only have impacts on capacity estimates during the ramp-up period.These findings allow shaping of the maximum capacity profile of a project. They can be used as a tool for quick assessment of conceptual capacities, and sensitivities of mining rates. Benchmarking tests compared favorably with projects, mines in operation and scheduling exercises. IntroductionA key consideration in the value proposition of a mining project is its capacity or production rate (Tatman, 2001). At a conceptual level, it is common practice to refer to empirical references (Taylor, 1986; Long, 2009), rules of thumb (de la Vergne, 2014), benchmark ing studies or consultant experience to estimate or validate a target value. There is, however, a lack of analytical methodology to guide an early estimate of the maximum capacity.Araneda and Gaete (2004) presented an interesting mathematical approach to estimate the capacity of panel caving mines. Using a continuous model, they confirmed that the mine capacity is essentially determined by the rate of area incorporation, in terms of area per period, and ore column height. This simple relationship has been confirmed by multiple detailed scheduling works"

May 1, 2016

By D. Denton, M. Stickney, R. Langston

The National Institute for Occupational Safety and Health and the Stillwater Mining Company worked cooperatively with the Montana Bureau of Mines and Geology to develop a system that would collect seismic data at the Stillwater and East Boulder mines. The purpose was to obtain baseline information on the magnitude and location of mining-induced seismicity to determine if the mines needed multi-channel in-mine monitoring systems. Seismic data recorded at field sites near the mines are being telemetered via FM radio through a series of repeaters to a central recording site where the seismic signals are digitized using an Earthworm data acquisition system. The Earthworm system performs several data analysis tasks in near-real time and places raw seismic data, preliminary hypocenter locations, and magnitudes on a Website within 5 min of a seismic event. Such rapid access to seismic data allows personnel at the Stillwater Mine, Spokane Research Laboratory, and Earthquake Studies Office to evaluate seismic events quickly and respond in ways that may improve the safety of mine personnel underground. Installation of the system also broadened earthquake coverage to south-central Montana, a region previously not covered by the seismograph network.

By Martin A. Elliott

Recommendations for safe practices in the operation of Diesel engines underground must take into consideration the hazards that might be created if the composition of the underground atmosphere differs from that of normal air. One aspect of this problem was discussed in the second report6/ of this series, which presented the results of tests in which a Diesel engine was operated with mixtures of normal air and exhaust gas supplied to the intake of the engine. Atmosphere .of this type were studied first because they will be present whenever the exhaust was is discharged into the atmosphere of underground workings in which an engine operates. Diesel engines in underground service may operate in another type of atmosphere, namely, one

Jan 1, 1941

By Martin A. Elliott

Recommendations for safe practices in the operation of Diesel engines underground must take into consideration the hazards that might be created if the composition of the underground atmosphere differs from that of normal air. One aspect of this problem was discussed in the second report6/ of this series, which presented the results of tests in which a Diesel engine was operated with mixtures of normal air and exhaust gas supplied to the intake of the engine. Atmospheres .of this type were studied first because they will be present whenever the exhaust was is discharged into the atmosphere of underground workings in which an engine operates. Diesel engines in underground service may operate in another type of atmosphere, namely, one

Jan 1, 1941

By Phillip E. Butler

Since early 1973, the Pennsylvania Department of Transportation (PennDOT) has been actively engaged in the utilization of coal mine refuse in the design and construction of highway embankments. The Soils and Geological Engineering Division of the Bureau of Materials, Testing and Research has the task of managing the program which includes field investigations, laboratory testing, engineering evaluation, planning, coordination, implementation, construction control, and review of construction performance. The objectives of the utilization program, in removing colliery refuse banks and utilizing the material in construction, are the environmental and aesthetic rehabilitation of those areas in the Anthracite and Bituminous coal fields which have been plagued for such a long time by air and water pollution, and unsightly landscapes; and the economic rehabilitation of those areas occupied by refuse banks by providing usable land which can now be developed as residential, business, or industrial sites.

Jan 1, 1975

The common approach of designing blasts on a trial and error basis is quickly coming to an end. When utilizing the full scale blast environment, trial and error can quickly become cost prohibitive and leaves much to be desired in terms of true blast diagnostics. In these situations testing is usually only continued until a perceived improvement is achieved and when the gross undesirables in blast results are removed. This does does not preclude, however, that further improvements of up to 100% or more can not be obtained.

Jan 1, 1991

By E. C. Tarpley, H. M. Cooper, R. F. Abernethy

"INTRODUCTION The determination of moisture in coal is an empirical test, because the time, temperature, and equipment are specified. The essential features of the equipment, and details of the procedure are given in A.S.T.M. Designation: D271-44 5/. According to the specifications, the following features should be incorporated in the equipment used:1. Oven must have uniform temperature in all parts.2. Oven must be constructed with minimum of air space.3. Oven must have means of changing the air two to four times per minute.4. Air must be dried over sulfuric acid (sp. gr. 1.84).The analytical procedures governing most of the nation's coal purchases are those given in A.S.T.M. Standards referred to above. These standards are general and of such scope as to cover all ranks and types of coal. In cases where only the moisture is required, a faster method than the standard procedure is desired.The semi-automatic moisture tester manufactured by the Brabender Corp. has proved itself in many industrial processes where the rapid estimation of moisture is of vital importance. With the approval of A. C. Fieldner, chairman, A.S.T.M. Committee D-5, and through the courtesy of Lowell Malan, chief chemist, United Electric Coal Companies, who loaned the tester, tests were made to determine the feasibility of using this instrument to determine the moisture in coal."

Jun 1, 1948

By Robert Goldstein

A computer program for calculating the illumination on coal mine surfaces due to machine-mounted lights is described. Utilizing numerical models of mining machinery and measured data on luminaire output characteristics, the program computes the ft-candle levels incident on the mine entry surfaces for any desired machine/luminaire/ entry configuration. Shadowing effects of the machine are taken into account. Results are provided at 2 ft. intervals on the face, left and right walls, floor and roof. To provide a data base for these calculations, eleven 3-D machine models were prepared and the outputs of three luminaire types were measured. Calculations were done for thirty different configurations.

Jan 1, 1977

This report describes the redesign, development and field demonstration of a remote shotcrete lining system, capable of operating in shafts and mines from 8 to 16 feet in diameter at depths up to 1000 feet. The original contractural scope of work outlining problems and remedial measures associated with a previous unit proved inadequate. Significant additional effort was necessary in order to fulfill the project objectives of producing a functionally reliable remote shotcrete lining system. Included with the engineering and technical description of the system, is a comprehensive technology package. Included with this material is ancillary equipment, materials selection procedures, mix-design data, quality control and assurance program, selection and training of personnel and the organizational aspects required to operate the entire system. The report concludes with details of a successfully completed borehole lining operation at the Nevada Test Site. An irregular 104 inch diameter borehole was lined at a rate of 4.8 feet per hour and 20 feet per hour respectively for 8-9 inch and a 2 to 3 inch shotcrete thickness.

Jan 1, 1983

By Glenn Norris, Tyler Buckingham

"Gold recovery gains in the order of one to two percent have been realized in 2009 due to changes in the operation of the grinding circuits at Barrick Gold Corporation’s Hemlo - Williams Mill. The initiative known as “split milling” involves milling low grade open pit ore in one grinding circuit and higher grade underground ore in the other grinding circuit under different conditions.The philosophy of split milling involves processing higher grade underground ore at a lower throughput rate and a finer grind while milling lower grade open pit ore at a higher throughput rate and a coarser grind. Bench scale tests showed that the recovery relationship for underground ore sources was much more grind sensitive than that of open pit ore. This relationship proved to hold in the plant. The gold recovery gain due to finer grinding of the higher grade ore is much greater than the recovery loss due to coarser grinding on the lower grade ore. Since the majority of gold is being recovered at a higher rate, this results in higher overall plant gold recovery when compared to the traditional operation philosophy of blending the ore sources.The challenges for achieving the maximum benefits of split milling were two fold; the need to increase throughput on the open pit ore milling circuit and a means of grinding finer on the underground circuit. The former was met with an increase in SAG (Semi-Autogenous Grinding) mill ball charge, a basic “drill to mill” blasting campaign and changes to the primary gyratory crusher. The latter was met with a reduced SAG mill ball charge and a higher milling density. The resulting benefits in additional gold recovered are in the order of $3-5 million per annum.INTRODUCTIONThe Williams Mill processes ore from three different ore sources, the David Bell Mine (DB), the Williams Underground Mine (WUG) and the Williams Open Pit (OP). All three ore sources are located within the Hemlo camp in Northwestern Ontario adjacent to the Trans-Canada Highway. The Williams Mill was built in the mid 1980’s at which time it was designed to process 3,000 dry metric tonnes per day through a 22’ SAG mill in series with a 16’ ball mill. In 1988 a Mill expansion doubled the mill capacity by adding a second identical grinding circuit. A photo of the current grinding circuit can be seen in Figure 1. Today the Williams Mill processes an average of 8,000 tonnes per day of which approximately 60% is from the Williams Open Pit."

Jan 1, 2010

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature of ash, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions~ issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1956

By K. Lang

A case study is provided that highlights the successful use of high efficiency electrical submersible pumps (ESPs) adapted from the oil and gas industry for a large scale, open pit mine dewatering operation. In this case, the mine is Goldcorp?s Peñasquito Mine, Peñasco and Chile Colorado open pit development areas in Zacatecas, Mexico. At the time of publication (July 2012), there were 18 vertical bedrock dewatering wells producing an average flow rate of 350 liters per second (lps) from the Peñasco and Chile Colorado development areas. Average pumping rate per well was 18 lps, with a maximum of 44 lps. The depth of wells varies from 330 m to 500m, and includes both in-pit and perimeter (ex-pit) pumping centers. A network of 50 piezometers was used to monitor the response of groundwater levels to pumping. Since dewatering operations were initiated in 2007, groundwater elevations decreased overall, from approximately 1950 m above sea level (masl) to around 1625 masl, for a total of 340 m of drawdown. The pit floor elevation was approximately 1655 masl. All of the producing wells were constructed with 16-inch boreholes, completed with 10-inch diameter blank casing and louvered screen sections and equipped with ESPs. The application of ESPs has proven to be highly effective in the case of Peñasquito?s dewatering operations. Noted advantages include the following: ? Small diameter pump allows use of smaller diameter boreholes (16 inches) and casing / screens (10 inches) reducing well drilling and construction costs ? Greater application range for flow rate and total dynamic head ? Variable speed drive systems for greater energy efficiency and flow rate optimization ? Integration of downhole instrumentation into the motor and pump assembly The advantages and benefits of using high efficiency ESPs revolutionized the dewatering program at Peñasquito open pit mine as evidenced by the number of deep vertical well installations and high dewatering flow rates and total dynamic head requirements.

Feb 27, 2013

By K. C. Armstrong, A. B. Cron, L. A. Melis

"The Johnny Mountain gold mine in northern British Columbia, owned by skyline Gold Corporation, has been in operation since August 1988. Mill operating difficulties at the start of the operation resulted in a depleted cash flow situation and quick improvements were required to generate a self-sustaining financial basis of operation. In October 1988, Melis Engineering Ltd. was contracted to identify metallurgical difficulties, implement necessary modifications, and undertake mill operations and personnel training in order to achieve production targets.This paper presents the operating difficulties which existed at start-up and describes the methodology used to overcome production problems. Metallurgical testing results are described along with the modifications made to the milling circuit to suit ore metallurgy. Plant changes led to the operation of a simple gravity/flotation circuit to recover gold as bullion and in a copper concentrate. Operation of the originally installed cyanidation circuit was discontinued. This contributed to substantial savings in operating costs and virtually eliminated environmental problems. PROPERRTY LOCATION ANR DESCRIPTIONThe Johnny Mountain mine site is located in northern British Columbia along the Iskuit River about 60 km east of Wrangell, Alaska and 275 km north of Terrace, B. C.. A location map is presented in Figure 1 and a site plan is shown in Figure 2. The complex is located on a mountain plateau about 3, 600 feet above sea level. The plateau is flanked to the north by Johnny Mountain and surrounded on the other sides by steep cliffs."

Jan 1, 1990