Search Documents

By Stephen C. Tadolini

The U.S. Bureau of Mines has developed ultrasonic measurement instrumentation capable of measuring strains and elongations on tensioned and untensioned mine roof bolting systems. This report evaluates the pulsed-phase-lock-loop and pulse-echo systems. The pulse-echo systems measure time of flight of a signal through the bolt. The ultrasonic instrument converts the measurement into elongations or stress. The most recent Bureau instrument development converts travel-time measurements directly into elongation, load, stress, and torque by simple data manipulation from the keyboard. Bolt preparation and instrument calibration are described in detail.

Jan 1, 1990

By M. Abzalov

"Control of analytical data quality is usually referred to in the mining industry as Quality Assurance and Quality Control (QAQC), and involves the monitoring of sample quality and quantification of analytical accuracy and precision. QAQC procedures normally involve using sample duplicates and specially prepared standards whose grade is known. Numerous case studies indicate that reliable control of sample precision is achieved by using approximately 5% to 10% of field duplicates and 3% to 5% of pulp duplicates. These duplicate samples should be prepared and analyzed in the primary laboratory.Bias in the analytical results can be identified by inclusion of 3% to 5% of the standard in each sample batch. Several different standards are used, with values spanning the practical range of grades in the actual samples. A blank (a sample in which the concentration of metal of interest is below detection limit) should also be included. Standard samples alone cannot identify biases introduced during sample preparation, and therefore approximately 5% of the duplicate samples (coarse rejects and pulp) should be processed and assayed at another, external, reputable laboratory.This paper discusses techniques used for estimation of errors in precision and accuracy, and overviews diagnostic tools. It is shown that one of the most commonly used methods, the Thompson-Howarth technique, produces consistently lower results than other methods. These results reflect the nature of this method, which relies on the assumption of a normally distributed error, and thus produces biased results when errors have a skewed distribution. This study concurs with the suggestion of Stanley and Lawie (2007: Exploration and Mining Geology, v. 16, p. 265-274) to use the average coefficient of variation (CVAVR(%)) as the universal measure of relative precision error in mine geology applications: Le contrôle de la qualité des données analytiques est habituellement désigné sous l’appellation d’Assurance et Contrôle de la Qualité (ACQ), elle implique le suivi de la qualité des échan¬tillons et la quantification de la reproductibilité et la précision analytiques. Les procédures des pro¬grammes d’ACQ impliquent habituellement l’usage de duplicata et de standards analytiques dont la teneur est connue. Plusieurs études de cas indiquent qu’une bonne fiabilité du contrôle de la précision des échantillons est atteinte par l’usage de 5% à 10% de doublons sur le terrain et de 3% à 5% de doublons de pulpe. Ces duplicata devraient être préparés et analysés au laboratoire principal.Un biais des résultats analytiques peut être identifié par l’inclusion de 3% à 5% d’échantillons standard dans chaque envoi d’échantillons. Plusieurs standards sont utilisés, avec des valeurs couvrant l’étendue des teneurs habituellement rencontrées dans des échantillons réels. Un blanc (un échantillon dans lequel la concentration d’un métal donné est sous la limite de détection) devrait aussi être inclus. L’emploi exclusif d’échantillons standards ne permet pas l’identification de biais résultant de la préparation des échantillons, de telle sorte qu’environ 5% des duplicata (rejets grossiers et pulpes) devrait être traités a un autre laboratoire indépendant et fiable.Cet article passe en revue les techniques utilisées pour évaluer l’erreur liée à la précision et a la reproductibilité, et effectue aussi un survol de divers outils diagnostiques. Il ressort de cet examen qu’une des techniques les plus fréquemment utilisées, la méthode Thompson-Howarth, fournit des estimés systémati¬quement inférieurs à ceux provenant des autres méthodes. Ces résultats sont un reflet de la nature de cette méthode, laquelle assume une distribution normale de l’erreur, biaisant ainsi les résultats lorsque l’erreur présente une distribution asymétrique. La présente étude recommande de privilégier l’usage du coefficient moyen de variation (CVAVR(%)) en tant que mesure universelle de la précision relative de l’erreu"

Jan 1, 2008

By MSHA website

“Conditions at underground and surface coal mines can change dramatically during the winter months,” said Joseph A. Main, assistant secretary of labor for mine safety and health. “We must be ever mindful of the seasonal changes that can affect our work environments.”

Jan 1, 2011

By Thomas E. Marshall, Michael Dunn, L. J. Prosser, Anthony T. Iannacchione

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) examined and characterized conditions at a majority of the underground stone mines in the United States. Observations at these mines revealed a limited degree of roof monitoring beyond visual inspection and sounding. When monitors are used, they typically require the miner to measure movement at the roof. If conditions are unstable, the mine rmay be in a hazardous situation while recording data. Based on this scenario, researchers surmised that a simple, inexpensive monitor with the capability of recording data at a distance from the mine roof would be a safer way to gain the information. Additionally, more widespread use of monitors could potentially lead to better understanding of roof movement in general. A monitor to meet this need was designed, tested, and subsequently improved as experience was gained in its’ use at a number of underground stone mines. The Roof Monitoring Safety System (RMSS) can provide an initial indication of movement in roof beams. By understanding and measuring roof movement in underground mines, the potential for injuries and fatalities to mine workers from falls of ground can be reduced. Also, officials at a mine with a history of data are better prepared to make a decision on remedial actions in the event of ground falls. This paper will outline the evolution of the RMSS and how it can be used in a comprehensive proactive ground control safety program. Also included is a case history describing how the RMSS was used in an evaluation of the effectiveness of a mechanical impact scaling machine at an operating limestone mine.

By W. R. Herrera

A research effort was conducted to present or develop methodology for evaluating candidate potting materials intended for use in explosion-proof enclosures. The primary purpose was to develop acceptance guidelines based on arc decomposition products. Acceptance criteria can be based on: ? Inherent thermo-chemophysical, mechanical and electrical properties; ? Arc decomposition products: ? Nature of volatile products produced, e.g., flammability, explosivity, synergistic effects on existing environment in the enclosure, toxicity; ? Quantity produced as a function of arc power and duration; ? Acceleration aging tests to evaluate breakdown under electrical stress.

Jan 1, 1982

By Christopher J. Bise

PRINCIPLES OF MINE PLANNING During the initial planning stages, all mining operations are analyzed and evaluated in a similar fashion. This similarity holds true because the mine-planning procedure can be reduced to a network of interrelated systems that are tied together by a common philosophy of mine planning: namely, that the resource is to be extracted in a manner which is safe, efficient, and profitable. The success of the mining operation cannot be guaranteed unless each of these three requirements is met. Fig. 1 shows a flowchart for the initial planning of any mining operation. Notice that there is a preplanning stage that leads to the planning of four interrelated systems. The preplanning stage includes property exploration, estimation of production and manpower requirements, and the establishment of construction timetables. The four systems, evaluated after the pre-planning stage, are broken down into the following: (1) Excavation and handling system, (2) Strata control system, (3) Operating support system, and (4) Service support system. The Excavation and handling system includes the selection of all the equipment for the removal of the resource from its in-place deposit (e.g., draglines, continuous miners, rock drills, etc.) and for the transportation of the mined material from the face (e.g., belt conveyors, trucks, etc.). The Strata control system incorporates all those considerations which maintain the integrity of the roof, ribs, floor, and overburden both during and after the extraction phase; typical considerations in this area include pillar sizing, artificial support of the immediate roof in mine entries, and subsidence protection. The Operating support system contains the "necessary evils" of mine planning; the system consumes a large percentage of the mining engineer's planning time but does not contribute to the actual extraction of the resource. However, if proper attention is not paid to the various components of the system, such as ventilation, drainage, and power, then the mining operation will not perform to its capabilities. Finally, the Service support system is composed of those operations which keep the mine running efficiently; typical examples of these include maintenance and sup- ply. One important concept that Fig. 1 is designed to emphasize is that the four systems are interrelated; typically, a slight alteration of one can affect the performance of another. If these interrelationships are ignored, the effects on the system can be disastrous. The mine preplanning stage and the four subsequent system evaluations constitute the Analysis portion of the mine planning flowchart. After this portion of the study is completed, the overall projected operation can be evaluated by techniques such as financial analysis. This last step in the study is referred to as the Synthesis of the previously calculated parameters into an overall plan. Much has been written about the overall evaluation of mining properties, but, over the past thirty years, very little has been written about the analysis of mine- planning systems in a coordinated manner. Further, those texts which attempted this topic have failed to give sufficient examples for successful implementation, thus supporting the operating engineers' lament that it is easy to discuss theories but difficult to show applications. This text is intended to bridge this gap. Examples of the various stages of the analysis portion of the mine planning flowchart shown in Fig. 1 will be covered in this text, with the exception of the Service support system, since this system is oriented more toward day-to-day planning than long-term mine planning. INTERNATIONAL STANDARDIZATION The benefits that can be derived from an international standardization of the units used in mining engineering calculations are numerous. The interchange- ability of equipment parts and the ability to analyze and compare performance and design specifications on an equal basis are just two of the goals desired by both manufacturers and mine operators. Unfortunately, conversion to an international standard has not been rapidly achieved by engineers in the United States, due to their training under the English system. The Society of Mining Engineers of AIME has made the commitment for the adoption of the Systeme International d'Unites (SI) in all mining engineering calculations. Since many practicing mining engineers and students in undergraduate programs still find difficulty in relating to SI units, the calculations in this textbook will use the English system, with Table 1 available for conversion into SI units.

Jan 1, 1986

By Edmond Chin

The land mass of the Asia and Pacific region comprises 11 million square miles or about 15% of the total Earth's land area. The bulk of the region is contained on the Asian continental land mass. Australia, the world's largest island or the world's smallest continent, alone is almost as large as the continental United States. The islands of New Zealand, New Guinea, Borneo, Sumatra, and Honshu are among the largest in the world. Collectively, they constitute a land area of 1.1 million square miles or an area about one-fourth the size of the United States. The countries in the Asia and Pacific region represent some of the most vibrant economies in the world. Japan is undisputed as one of the world's leaders in manufacturing and commerce. Hong Kong and Singapore are significant both as entrepôt and banking centers. The economies of Australia, the Republic of Korea, and Taiwan compare favorably to the level of the industrialized countries in western Europe. Indonesia, Malaysia, the Philippines, and Thailand have maintained strong economic growth during the past two decades. All these countries in the Asia and Pacific region collectively constitute a significant bloc as to raw materials production and consumption, as to manufacturing, and as to world trade.

Jan 1, 1992

By Norman O. Lotter, Virginia Lawson, Mika Muinonen, Dominic Fragomeni, Jorge F. Oliveira

Development of metallurgical flowsheets from drill core to production of finished metal involves two main domains: process mineralogy to sample the ore and develop a successful flowsheet producing saleable concentrate; and extractive metallurgy to convert that saleable concentrate to finished metal. Effective flowsheet development for a new or brown-field concentrator and processing facility is essential to project schedule and return on investment. Over the last decade in particular, the integration of geology, mineralogy, sampling, and mineral processing have empowered the development of an improved practice in flowsheet development. The use of geometallurgical units as a basis for best-practice sampling delivers representative study material to the laboratory. Modern automated mineralogy characterises the whole rock assembly and paymetal mineral hosting, to address downstream process implications. Batch scale flotation testing then uses this information to design and perform well-focused strategies. At early stages of the project, the Extractive Metallurgy team is engaged to determine processing constraints or other economic drivers in conversion of the saleable concentrate into finished metal. The team evaluates available technologies, assesses the impurities and key properties of the given concentrate. In many cases, changes to mineral processing flowsheet are required to maximize value per tonne of concentrate. Site conditions, availability of infrastructure, energy and power all play an important role. Modern metallurgical simulation tools such as FactSage™ and METSIM™ can quickly define the appropriate test program for each process. Bench scale testing and appropriate scale of piloting can confirm simulations and provide design criteria. A case study demonstrates how effective use of these tools and a multidisciplinary team can accelerate flowsheet development, while reducing costs and ensuring that the designed processing facilities maximize project value with minimum risk.

Jan 1, 2014

By Kermit G. Davis, Sean Gallagher, William S. Marras, Kimberly Kovacs

This study evaluated spinal loads associated with lifting and hanging heavy mining cable in a variety of postures. This electrical cable can weigh up to 10 kg per metre and is often lifted in restricted spaces in underground coal mines. Seven male subjects performed eight cable lifting and hanging tasks, while trunk kinematic data and trunk muscle electromyograms (EMGs) were obtained. The eight tasks were combinations of four postures (standing, stooping kneeling on one knee, or kneeling on both knees) and two levels of cable load (0 N or 100 N load added to the existing cable weight). An EMG-assisted model was used to calculate forces and moments acting on the lumbar spine. A two-way split-plot ANOVA showed that increased load (p<0.05) and changes in lifting posture (p<0.05) independently affected trunk muscle recruitment and spinal loading. The increase in cable load resulted in higher EMG activity of all trunk muscles and increased axial and lateral bending moments on the spine (p < 0.05). Changes in posture caused more selective adjustments in muscle recruitment and affected the sagittal plane moment (p < 0.05). Despite the more selective nature of trunk EMG changes due to posture, the magnitude of changes in spinal loading was often quite dramatic. However, average compression values exceeded 3400 N for all cable lifting tasks.

By André Desbiens, Jocelyn Bouchard, René del Villar

"The metallurgical performance of the column flotation process is determined by the concentrate grade and recovery. Although the former can be continuously measured using an on-stream analyzer, the latter must be estimated by a material balance calculation based on seldom verified steady-state assumptions. Consequently, the automatic control and optimization of flotation columns should be performed using secondary variables having a strong influence on the metallurgical performance, such as froth depth, gas hold-up or bubble surface area flux and bias. The aim of this paper is to present a model-based automatic control strategy using froth depth and bias measurements obtained from virtual sensors developed at Laval University. Preliminary pilot plant results on two-phase (water– air) and three-phase system (water – minerals – air) will be presented and eventual industrial implementation of such a strategy as well as the possibility of achieving effective real-time optimization from bias and froth depth measurements will also be discussed.INTRODUCTIONFlotation columns have been widely studied and used in mineral processing for about twenty years. Although a great deal of work has been accomplished to understand the influence of different variables such as froth depth (H), bubble surface area flux (Sb) and bias (Jb) on the metallurgical performance, the measurement of some of these variables is still difficult to be performed – except at the laboratory level – because in most cases, no commercial device yet exists.As a result of this, it is almost impossible to achieve neither efficient control nor optimization of the process at the industrial level, even in open-loop operation. This paper aims at presenting a simple control strategy of froth depth and bias. Description of the sensors used to achieved measurements, preliminary pilot plant results for froth depth control, eventual industrial applications and possibilities for process optimization are also treated."

Jan 1, 2003

By A. D. S. Gillies

The use of refuge chambers for use in handling underground emergencies is an issue of topical relevance within the US mining industry. Chamber design is of importance to meet some new safety requirements of US federal and some state government mine regulations. A review has been undertaken of a steel mine refuge chamber design to predict what will be internal temperature within the chamber over an extended period with miners present? The design has been examined for the situation when the chamber is sited in still mine air. Spreadsheets have been developed to allow various design assumptions to be tested. The evaluation has been undertaken using thermodynamic heat transfer models with some assumptions specified to produce a model of appropriate simplicity but with adequate degree of accuracy. Under normal still air conditions it can be seen that internal chamber conditions rise quickly to often arduous conditions. There will always be quite a few assumptions necessary in complex heat transfer process evaluations. Some important refuge chamber design parameters are: ? External surface area of the chamber, its wall thickness and construction. ? Metabolic heat generated and number of persons making use of the chamber. ? The temperature of the external mine atmosphere to the chamber over the year and the influence of geothermal gradient on temperature at depth. ? The maximum internal chamber Apparent Temperature considered safe. ? The distance inside the underground mine and adjacent ventilation conditions.

Jan 1, 2012

By H. R. Babitzke

As part of a continuing project to develop refractory metal alloys for high-temperature structural applications, the Bureau of Mines applied solid solution and precipitation strengthening techniques to improve the properties of columbium alloys. The purpose was to investigate the effects of hafnium, tungsten, and boron on the formability, strength, and oxidation resistance of columbium. The experiment was of factorial design with two replications which called for 72 ingots of 36 basic compositions, weighing 150 grams each. Hafnium, tungsten, and boron were evaluated at 3, 3, and 4 levels, respectively. Values of alloy content are all in atomic percent. The highest strength observed was 29,000 psi at 1,200° C for alloys Cb-15Hf (No. 3), Cb-7.5Hf-5W-2B (No. 14), and Cb-15Hf-5W-2B (No. 15). At 1,200° C, the ternary alloy Cb-15Hf-5W (No. 6) which has shown good properties in previous Bureau of Mines investigations was the most resistant to oxidation For boron additions, the alloys oxidized more readily with increasing amounts of this element. The fabricability of the alloys high in boron became increasingly difficult, resulting in an inadequate number of alloys required for a complete statistical analysis for all the tests. As a result of the decrease in ductility, an insufficient quantity of tensile samples were available for a proper analysis for the high-temperature strength data.

Jan 1, 1970

By Nathaniel Arbiter

Flotation’s earliest patent was issued in 1860. However, the process was first applied commercially in Australia until 1904, and in Montana in 1911. Major advances followed both in reagent treatment and in cell design, with resulting process improvements. Mechanical cells have seen the widest use and with the major increases in plant capacities (Fig. 1) their volumes have also increased (Fig. 2). In 1991, the principal use for the process was to produce copper concentrates for smelting. It was applied to 243 Mt (268 million st) of copper ore. The total of all ores floated that year was 426 Mt (470million st). In 1997, US mines produced 257 Mt (284 million st) of copper ores for flotation, yielding1.75 Mt (1.94 million st) of copper.

Jan 1, 2000

By Bill Starke

The acceptance of AugerCast piles in Canada has been limited. Many engineers are apprehensive about the quality of the piles produced by this method. However, advances in the sensing instruments and computer technology can now provide satisfactory levels of quality assurance. Post construction tests such as the sonic echo method can give an indication of pile shaft integrity. Computerized monitoring of the pile installation process is an immediate and more positive method of quality assurance. The computer continuously measures and records the parameters which indicate the quality of the pile. If these parameters do not indicate a satisfactory pile, it is replaced before the concrete hardens. Computerized monitoring of the installation process is another tool available to the engineer. The data from this system analyzed with soil borings, site inspections, and possibly sonic tests can provide the engineer with enough information for pile certification.

Jan 1, 1997

For small particles of niekel flotation eoncentrate (av. size 50 pm) the predominant heat transfer mechanism under suspension smelting conditions, prior to ignition, is conduction from the gas and not radiation from nearby hot bodies. Results of laboratory tests using gas temperatures 380-700&#176;C and furnace wall temperatures 380-1100&#176;C were in accord with heat transfer theory. In practieal flash smelters earlier ignition, and hence better utilization of the space in the shaft, would result from introduetion at the top of the shaft of gases hotter than the ignition temperature of 500-600&#176;C.

Jan 1, 1979

By Rimas Pakalnis, Tom Brady, Lewis Martin

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate weak rock masses (such as are associated with operations in the Carlin Trend in Nevada) into existing design relationships. The original database that led to most of the empirical design relationships presently employed in hard-rock mining was derived from fair-to-good-quality rock. In this study, the relationship between weak rock quality and opening design (nonentry/entry methods) is being investigated. The common factor in all mines is a weak back or wall. This work attempts to provide tools that will enable a mine operator to make economic decisions that will also ensure a safe working environment.

By D. S. Choi

This paper presents a theoretical analysis of the effect of shape and size on strength of geologic materials. The results indicate that the shape effect is caused by the development of confining pressure at the interfaces. The linearization of the obtained formula is of the same form determined by experiments. The size effect is attributed to the fact that the geologic materials contain discontinuities in the form of fractures, bedding planes, and cleats. The maximum reduction factor for the size effect is the one-sixth power of the volume of a cubic test specimen. The results of this work are particularly useful in determining the strength of coal pillars in underground mines.

Jan 1, 1989

By Mitchell L. Spencer, Viswanathan Panchanathan

"Bonded magnets are important category in permanent magnets. They are made by one of the following processes: compression bonding, injection molding, extrusion, calendering. An overview of the various bonded magnet processes and properties of products made with different magnet materials along with their applications are discussed. The main emphasis will be on the use of bonded NdFeB and ferrite magnets.IntroductionBonded magnets are a major growth area in permanent magnets. Bonded magnets are made by any one of the following processes: Compression bonding; Injection Molding; Extrusion and Calendering [1,2]. Compression and injection molded magnets are rigid magnets. Materials used in calendering process produce flexible magnets. Only the extrusion process makes both rigid and flexible magnets. The binders used for the bonded magnets vary depending on the processes. Thermoset, thermo-plastic and elastomeric binders are respectively used in compression, injection and the calendering process. Extrusion molding uses elastomers or thermo-plastic materials. The most co=on magnetic materials, Ferrite, SmCo, Alnico and NdFeB can be used in any of the above processes either alone or in combination as hybrid magnets. Another material that has been developed for co=ercial application is SmFeN. Making the material has been challenging and it is being used in niche market applications in limited quantitiesIn the extrusion process, a highly loaded compound is used to produce strip or sheet and is continuously extruded through a die. In calendering the granulated compound is rolled to produce a continuous wide sheet. In the compression bonding process a uniaxial pressing force is used. These magnets have higher loading compared to injection molded magnets. In injection molding the material is forced into a mold cavity and has lower loading compared to compression molded magnets [2,3]. Most of the flexible magnets are made using extrusion and calendering processes and the most co=on magnet material is inexpensive ferrite. Flexible magnets have been made using rare earth materials, but on a very limited basis.The major advantages of magnets processed by extrusion and calendering are as follows: inexpensive tooling, automation; practically any 2D geometry; fast production rates; no chipping or breaking; a wide range of properties; on-line magnetization; easy to convert (e.g. cut, punch or shape).Compression bonded magnets are inexpensive to manufacture. They have higher magnetic properties compared to injection molded magnets; however lower than their sintered counterparts. The magnet shape is restricted to simple geometries and they require careful handling. Their isotropic nature allows complex magnetizing patterns."

Jan 1, 2013

Mr. BRADFORD said :-On assuming this chair, which has been occupied by so many gentlemen of conspicuous ability; my first words must be an expression of the gratitude I feel for the honour you have done me in electing me to be your President for this year.When considering the subject matter of this address to you to-night, quite frankly may it be stated that for a long time I was on the horns of a very great dilemma, for while I could discourse on the modern political trend in relation to our industries at great length, it appeared to me that this was not the place for such a discussion. Next I turned to a consideration of whether a discourse on the theory and practice of iron and steel would be of interest.I, however, banished this idea also from my mind, because it appeared to me that you have already had a surfeit of this on your visits of inspection to our local industries and I did not want in any way to be held responsible for the iron entering into your souls! I therefore propose, with your kind consideration, to address you on other subjects of common and vital interest to all.My first words and thoughts turn on the absolute necessity of eliminating waste in our methods. If we are to succeed in our...

Jan 1, 1926

By D Craw

The Old Man Range, south of Alexandra, in central Otago consists of a package of highly folded greenschist facies schist of the Wanaka lithologic association. The range is crosscut by several east to ENE-striking high angle gold-bearing quartz veins, (eg Whites Reef and Grays Reef), which were extensively worked in the late 1800s. The range is bounded on its east side by the Old Man Fault, which separates these rocks from generally flat lying and planar Caples Terrane schist. To the west of the Old Man Fault, about halfway up the range, a large subparallel, 100 m wide fault zone strikes NNW and appears to cut off the historic veins. The fault zone consists of highly sheared and folded rocks and numerous high angle cataclasites and centimetre-scale clay gouge zones. Hydrothermal alteration is not apparent and the individual faults and shears are clay altered, possibly due to weathering, without visible quartz veins. Gold, limonite pseudomorphs after pyrite and rutile are concentrated in some of the narrow cataclasites and gouge zones. These mineralised structures are texturally similar to the gold-bearing reefs and may be structurally related. It is postulated that the NNW-striking shear zone and ENE-striking veins may be a conjugate array formed during a period of Cretaceous normal faulting.

Jan 1, 2004