Search Documents

By J. H. Bain, D. C. Haigh, L. C. Parsons

Jan 1, 1964

By George S. Rice

"The emission of hydrocarbon gases from coal beds and contiguous strata causes many accidents in coal—mine workings, the number of fatalities so caused being second only to those due to falls of roof. Gases tend to increase in amount with depth of coal mining, hence the danger of explosion is increased with depth. The pressure of the gas in virgin—coal areas at a distance from mine workings likewise tends to increase with depth from the surface, probably due to corresponding increase in hydraulic head and possibly, when the gas is held in nonporous formations, to greater ground pressure. The rise in gas pressure with depth under usual conditions is shown in wells drilled from the surface and in some coal fields in drill holes into the face of workings; however, under normal conditions of coal formation gas does not issue into workings under high pressure because the coal and adjacent strata have many bedding and joint planes which allow the gas to escape freely at the face of the workings. The rare occurrence of instantaneous outbursts of gas, with violent effects referred to later, constitute the exception.Variations of volume and pressure of fire-damp or methane found in different coal beds by wells at a distance from mine workings, are analogous to variations in volume and pressure of natural gas found in different gas and oil sands, although in general the pressure tends to increase with the depth. Sometimes, however, in tight sands higher in the formation the pressure of gas therein is abnormally high, and on drilling the well deeper gas in the lower strata may be found at lower pressure."

Jun 1, 1934

By R Thomson

The use of uranium metal in non-ferrous metallurgical practice is dis-cussed with reference to its alloying behaviour and chemical activity. It is suggested that the more promising applications are in the treatment of molten metals to combine with impurities. Mines Branch work along these lines is described for copper, zinc, magnesium, aluminum and nickel alloys. It is shown that a cop-per-uranium master alloy (25 per cent U) successfully deoxidizes molten copper without detriment to the electrical or mechanical properties of the product at residual uranium levels of up to 0.8 wt. per cent. Additions of uranium to alpha brass in amounts greater than the lead impurity content were found to remove the deleterious effect of lead on hot-workability. Similar deoxidizing and malleableizing effects were found with uranium additions to nickel. It is thought that uranium forms stable intermetallic compounds with many impurity elements. A significant malleableizing effect can therefore be expected in the presence of other elements besides lead.

Jan 1, 1963

By D Vickers, N C. Fowke

The reduction of geological risk for planning of high production longwall faces is essential. Geological and geophysical techniques applied at Huntly West Mine before 1989 were unable to reduce the geological risk to an acceptable level. The success of a trial long-hole directional drilling programme at Huntly West Mine (Fowke et al, 1989) has encouraged the Coal Corporation of New Zealand to use the technology long-term, for seam definition. Initial drilling in 1989 completed a total of 3543 metres, with the longest borehole length being 369 metres (limited by number of rods available). A major re-interpretation of seam structure resulted from the drilling, which was able to fill in seam details between surface exploration boreholes. The undulating thick seam conditions at the mine require a refinement of drilling strategies used overseas. Long-hole directional drilling also displays potential for inseam gas drainage. Gas flows of the order of 1000 L/min were initially indicated in individual boreholes. Other gas parameters of the seam have been studied by Beamish et al (1991), and highlight the significance of the natural gas resource in the Huntly Coalfield.   The continued development of drilling technology will be of major benefit sustainable development, particularly in policy.

Jan 1, 1991

By Brian Danyliw

"Dust control is an increasingly important consideration for all mining operations from a health, safety, environmental and maintenance perspective. Modern mining operations incorporate a variety of mechanical dust control techniques into design however in many cases these engineered systems are unable to meet desired fugitive dust level targets. In these cases a variety of chemical dust suppression options are available to operators to assist in meeting their targets. This paper provides an overview of available chemistries, discussion of application techniques and equipment requirements and available performance monitoring technologies. This paper will also include a number of case histories discussing the treatment approach chosen, challenges encountered, chemical feed, storage and application equipment, monitoring techniques employed and results achieved.INTRODUCTIONDust FundamentalsFugitive dust by definition is an aerosol consisting of particulate matter suspended in a gaseous medium. Aerosols can include suspensions of particulate (solids) or sprays (liquids) or a mixture of both. Of particular concern from an occupational health and safety perspective are aerosols of particulate matter due to their involvement in classical occupations lung diseases such as silicosis, poisoning through chronic exposure to compounds such as lead and beryllium and expected involvement in more modern identified conditions such as cancer, asthma, and a host of other respiratory and non-respiratory conditions which may be caused or influenced through exposure to dust.According to the ""Glossary of Atmospheric Chemistry Terms"" (IUPAC, 1990), ""Dust: Small, dry, solid particles projected into the air by natural forces, such as wind, volcanic eruption, and by mechanical or man-made processes such as crushing, grinding, milling, drilling, demolition, shoveling, conveying, screening, bagging, and sweeping. Dust particles are usually in the size range from about 1 to 100 µm in diameter, and they settle slowly under the influence of gravity."" It should be noted that the behavior of particulates with respect to settling rate in air is a function of particle mass and shape and therefore the geometric size of the particle can be misleading. Occupational hygienists utilize the concept of particle aerodynamic diameter as a more representative reflection of particle size. Particle aerodynamic diameter, is defined as ""the diameter of a hypothetical sphere of density 1 g/cm3 having the same terminal settling velocity in calm air as the particle in question, regardless of its geometric size, shape and true density."" The expression of particle size as aerodynamic diameter allows for a more consistent understanding of particle behavior both from a settling perspective as well as from the perspective of how dust particles will behave in the respiratory tract. Figure 1 illustrates settling rates for particles of various aerodynamic diameters. The relationship between particle size and settling rate is important for understanding what size of particles must be addressed by dust control strategies as well as what particle sizes represent the most danger from an exposure and occupational health perspective."

Jan 1, 2015

By Steve Kral

The domestic mining industry may be in the doldrums but there appears to be hope, at least from a regulatory standpoint. At least one US senator believes that the events of Sept. 11, 2001 made many citizens see the need for the country to become more self-reliant on its growing energy needs. Even before that tragic day, however, the Bush administration was making a strong push to open up more public land for energy and natural resource development.

Jan 1, 2002

By IPMI Educational and Scientific Foundation

It is with great pleasure that we announce the availability of this fourth issue of the IPMI Journal, a publication of the International Precious Metals Educational and Scientific Foundation. This digital peer reviewed publication has been created as a vehicle for the sharing of technical information related to the science and technology of precious metals. Since 1976, the International Precious Metals Institute has championed the exchange of information of critical importance to the precious metals scientific and commercial communities through its various communications vehicles. This has included instructional videos, annual conference symposia, special topic committee meetings, regional seminars, and professional and student achievement awards. Due to the breadth of important topics related to all aspects of precious metals, it has been the vision of the IPMI to provide a publication available to the general public that would become a key source of pertinent topics containing high quality publications by experts in their fields of study. Historically, the IPMI has attracted world renowned experts in many fields (including Nobel Laureates Henry Taube, Ei-ishi Negishi, Robert Grubs, Professor Ben Feringa, and David MacMillan) in the dissemination of discoveries, inventions, and industry proven practices. Such information has a total value greater than the sum of its parts as seemingly unrelated innovations from distinct focus areas can be adapted to solve problems. Because of this important characteristic of information exchange, we have decided to create a digital journal, available to the general public, that will not only communicate state of the art discoveries and sound practices, but will also review historical communications from the IPMI’s archives that have value and use even in today’s environment. On behalf of the members and leaders of the IPMI, we hope you will find value in this new publication.

Dec 1, 2020

By Ryan C. Linthicum

A system of steel sheeting and multiple levels of high capacity double corrosion protected soil anchors were used to restrain a major slope failure that occurred at the base of the Watchung Mountains mid-way through construction of a 650,000 SF retail center along Route 22 in Watchung, New Jersey. The implementation of a design-build earth retaining structure was necessary to stabilize and repair the disturbed mountainside in a timely fashion to permit completion of the retail center on a fast track schedule. The tied back steel sheetpile wall was approximately 2,000 feet long and varied in height from 12 to 25 feet. The hillside extended approximately 350 feet above and 600 feet beyond the wall with the main failure scarp extending 50 feet above and 90 feet beyond. The wall was constructed in a top-down manner and required the installation of 475 anchors to resist loads of up to 70 kips/ft produced by the creeping hillside and groundwater flows from both a series of springs and steady state seepage through an inclined zone of fine sand. Incorporation of a unique tie point connection eliminated the need for a waler, facilitating and simplifying modifications to anchor locations based on anchor load test results and conditions encountered during construction. Post grouting also proved to be an essential element in the successful construction. This paper presents the design and the construction methods used to restrain the significant earth lateral loads produced by a slope failure using steel sheeting tied back with high capacity soil anchors with anchor loads distributed to the sheeting through a unique tie point connection on a fast track schedule. Installation techniques, testing programs, and construction quality control are also discussed.

Jan 1, 2003

By Pilon CG, Deakin RC

It is proposed that a waste rock dump be constructed on slopes consisting of soft colluvium and weathered Chim Formation mudstone at the Porgera Gold Mine, in Enga Province, Papua New Guinea (PNG). Geolog- ical, geomorphological and geophysical investigations were conducted in support of geotechnical studies to assess the physical character of the 6km2 site. Geomorphological studies focused on the extent and nature of colluvium cover and landslide activity. Detailed ground traverse mapping resulted in classification and delineation of eight terrains and seven material types. Seismic refraction and resistivity profiling, combined with drilling, provided subsurface data. Results were presented as standard profiles, coloured contoured sections and plans. Subsurface features, including deep colluvial channels, buried cliffs, slump blocks and buried alluvial channels, were identified. Results of the combined investigations allowed designers to model the colluvium/ bedrock surface and identify critical areas of deep, mobile colluvium and weak bedrock. A design approach was developed which accounted for the morphology of landslide systems and distribution of colluvium types.

Jan 1, 1991

By Bujtor G. J, McMahon D. W

This guide to the understanding of ore reserve estimation is the revised version of a report with a similar title circulated within the CRA Limited (CRA) group of companies in mid-1980. It is the principal result to date of an Ore Reserve Study commissioned by CRA in late 1977.This guide to the understanding of ore reserve estimationis the revised version of a report with a similar titlecirculated within the CRA Limited (CRA) group ofcompanies in mid-1980. It is the principal result to dateof an Ore Reserve Study commissioned by CRA in late1977.The study was prompted by two ore reserve situations.The Zinc Corporation and New Broken Hill Consolidated,Broken Hill, had reached the point of havingto find a replacement 'for their traditional ore reserveprocedure and Mary Kathleen had to admit publicly thatore reserve predictions would not be realized. Thesewere not however the only problems to be looked at. Asmentioned more fully later, other ore reserve situationswere known, or were met during the study, in copper,gold and nickel as well, where poor realization: expectationratios had ranged from embarrassing to disastrous.These made it clear that ore reserve estimation had to belooked at afresh.The fresh look has resulted in a broadening of theconcept of ore reserve estimation from its traditionalpurely computational basis to an approach embracingall the many things that can affect expectation andrealization as essential factors. Hence this guiderepresents a gathering together of what has been learnedand what should be known to all those concerned withore reserves in any of its diverse aspects.The study has been marked"by a number of changesof thinking. At first the aspects that appeared to requireattention were two; recognition that an ore reserve statementwas an estimate, not a precise calculation; and asearch for im improved estimation procedure adapted tolow grade ores with narrow economic margins. Threeyears later the view was that the need was to incorporateinto ore reserve estimation all relevant aspects of theproposed mining operation from choice of a samplingmethod to sales contract specifications.This study is thought to be unique in being frankabout weaknesses in ore reserve estimation and intreating failures not as natural disasters (like drought orflood, which have to be endured) but as potentiallyavoidable. It has led to three principal conclusions.

Jan 1, 1982

By J. E. House, C. J. Lewis

In the solvent extraction process, also referred to as liquid-liquid extraction, the clarified uranium-pregnant sulfuric acid leach solution is contacted with an organic extractant dispersed in kerosene; the uranium enters the organic phase and associates itself with the organic extractants. Simultaneously an-ions or cations, as the case may be, leave the organic extractant phase and enter the aqueous phase. The two phases are then allowed to separate by virtue of their immiscibility. Based on the data available, a generalized procedure for the recovery of molybdenum from the sodium carbonate scrub liquor of acid leach uranium mills using secondary and tertiary amine extractants is presented, as is another generalized procedure for the recovery of molybdenum from the bleed stream of alkaline leach uranium mill circuits. Such economic appraisal as can be made at this stage of the development is also indicated. Molybdenum occurs in most uranium ores. Whether the uranium is solubilized by the acid leach route or by the alkaline leach process, some of the molybdenum present in the ore is solubilized along with the uranium. Molybdenum in uranium mill pregant solutions may cause processing difficulties, among which may be mentioned the poisoning of resins, the precipitation of organo-molybdenum complexes, or the build-up of molybdenum in recycle streams. While the uranium milling industry has been successful in applying measures to overcome the problems arising from the presence of molybdenum in the circuits, such measures nevertheless add to the cost of producing uranium yellow cake concentrate. Table I shows the analysis of typical uranium pregnant leach solutions. Uranium recovery by solvent extraction is presently practiced only in conjunction with acid leach circuits, and it may be noted that of about 16,000 tons of uranium ore daily processed by sulfuric acid leach, more than half of this tonnage follows the solvent extraction route. Uranium mills leaching ore with sodium carbonate-sodium bicarbonate solution (the so-called alkaline leach circuit) do not use solvent extraction. In this case the uranium pregnant solution is sufficiently pure to permit the direct precipitation of uranium concentrate with subsequent recycle of the alkaline leach solution. While solvent extraction procedures may be developed which are economically attractive for the alkaline leach uranium process, this has so far not been the case. The earlier uranium mill solvent extraction circuits used organo-phosphate extraction reagents, among which di-2-ethylhexyl phosphoric acid was popular. It should be borne in mind that uranium in its sulfuric acid leach solution exists in an equilibrium involving uranium in both anion and cation forms: uo + 2S0 = [uo2(so4)2] For this reason uranium may be extracted by either cation extractors or anion extractors and this is likewise true of molybdenum. However, the organo-phosphate extractants also load ferric iron which is usually present in the uranium acid leach solution. For this reason, it is necessary to reduce this solution substantially to the ferrous state ahead of solvent extraction using organo-phosphate reagents. The amines, being anion extractors, selectively reject iron and thus render the iron reduction step unnecessary. In the solvent extraction process, also referred to as liquid-liquid extraction, the clarified uranium-

Jan 1, 1961

By Y. Sasseville

"Niobec has been using vibrating screens and screw classifiers as a double stage classification in its grinding circuit since the very beginning of its operation in St-Honoré. Most of the other mineral processing plants around the world uses cyclones as the classification device in their grinding circuit. The difference between these two methods are well known in terms of capital cost and grinding efficiency but the differences in terms of the impact on the downstream processing stages are a lot harder to predict and are case specific. In the interest of lowering the capital cost of a future expansion project, Niobec decided to test the cyclones in its actual grinding circuit and evaluate their impact on the recovery of the downstream processing stages as well as the operating cost of the mill. We switched between cyclones and screens for 8 month in 2013 and early 2014 and we are now operating only with cyclones since march 2014.INTRODUCTIONThe Niobec mine and concentrator were built in the mid 70’s and at that time, the mill was processing 1 500 tons per day. Over the years, many expansion projects have brought the plant to 7 000 tons per day. Throughout the initial concentrator design and commissioning, screens have been chosen over cyclones because of their higher classification efficiency which is known to reduce variability and limit the fine generation especially due to a high undersize classification efficiency. Just like many other plants, fine particle generation is a major problem at Niobec because of its negative effect on downstream processing stages. In the interest of lowering the capital cost of a future expansion project, Niobec’s engineering team decided, 35 years later, to test the cyclones in its actual grinding circuit and evaluate their actual impact on the final recovery and the operating cost of the mill.The grinding circuit is separated in two lines which will be called Circuit #1 and Circuit #2 along this paper. Circuit #1 is, as you can see in Figure 1, composed of a rod mill and two parallel ball mills in closed circuit with screens and screw classifiers. The screens oversize are sent to the screw classifiers while the undersize are sent to the next processing stage. The screw classifiers overflow are both sent back to the pump box while their oversize streams return in their corresponding ball mills for further grinding. Circuit #2 is, as you can see in Figure 1, quite the same as Circuit #1 except it has only one set of screw classifier and ball mill. Figure 1 also shows the modification in arrangement each circuits went through to integrate the new cyclones. One of the ball mills in Circuit #1 now appears dotted because it can still be used but is not now"

Jan 1, 2015

By Tim O’Neil

If you build a big truck, build a big tire to match it. Let that haulage synergy aid the economics, productivity and lessened maintenance for the unit. Now, Cater-pillar and Michelin have done just that. Discussions began in 1996. Caterpillar was making plans for its 797 ultra-class haul truck. The development team realized the need for a tire that could withstand extreme loads. The 797 would weigh 558 t (615 st) and be capable of 64 km/h (40 mph) speeds. So Caterpillar approached Michelin. The two companies realized the benefits of jointly developing a tire for the 797.

Jan 1, 2002

THE area dealt with in this paper is included within a radius of about 3 miles of the Poimena township. Several thousand tons of tin have been won from this field, and probably £200,000 spent in exploiting it.PREVIOUS LITERATUREThe field has been reported on by Government geologists on four occasions and several ,articles on it have appeared in the mining journals. The work done by Government geologists is summarized below:-"Report on the Blue Tier Tin Mining District and its Tin Deposits", 1886.Speaking of the tin-ore occurrences, this paper states:-"In the primary granite the lodes of tin ore occur, also dykes and belts of more recently obtruded porphyries. The really valuable metalliferous deposits may be classified as follows :-1. Lodes (of which the Lottah mine is typical).2. Dykes- (a) Indurated or hard (as shown by the formations at the Anchor and Cream Creek mines). (b) Soft (eg Hayley's Lease).

Jan 1, 1912

By R. L. Bruening, N. E. Izatt, S. R. Izatt

"Rare earth elements (REE) are essential and unique components of many high-technology products without which functioning of modern society would be greatly impaired. Commercial deposits of REE are limited to a few geographical locations. Largely untapped sources of REE are available in endof- life (EOL) magnets, rechargeable batteries, and electronics. Presently, < 1% of REE in EOL wastes is recycled. Conversion of EOL wastes to liquid streams allows use of IBC’s Molecular Recognition Technology (MRT) process to selectively recover, separate, and purify target REE and associated metals at g/L to mg/L or lower concentration levels. The MRT process together with its applications to separations of REE and associated metals in recycling as well as in mining are described. Economic and environmental advantages of MRT are presented. INTRODUCTIONRare earth elements (REE) include the lanthanide series (La-Lu), Y, and Sc. These elements are not rare, but concentrated minable deposits are scarce (Cordier 2012; Haxel, Hedrick, & Orris, 2002). Over 95 % of the world’s supply of REE is controlled by China (Hanson, 2011a) where they are mined, processed, and the pure elements incorporated into a growing number of consumer and military products. The consumer products are marketed worldwide. Since REE are vitally important in consumer and military products, this situation has caused other nations to scramble to develop the capability to produce their own supply (Cordier, 2012).In the U. S., Molycorp has reopened the Mountain Pass REE mine in California and production has begun (Goldenberg, 2010). Development of a reliable internal source of REE is of high national priority in the U.S. (Hanson, 2011b; Hess, 2012: “Obama Announces”, 2012). These elements have in recent decades been incorporated into new consumer and military products that are essential to our economy and defense. These products range from wind turbines, high performance magnets, hybrid car rechargeable batteries, energy efficient lighting electronics, flat screen televisions, and smart phones to advanced weapons systems (Haxel et al., 2002; Levkowitz & Beauchamp-Mustafaga, 2010)."

Jan 1, 2012

By Richard A. Rivell

This document is a users manual intended as a reference for personnel interested in the analysis of coal-mine-electrical-power systems under either normal operating conditions or fault situations. The interactive procedures developed for this purpose are described and implementation considerations are discussed with respect to the mine-power system. Considerations for choosing a solution technique and a number of examples are included. Procedures available include Gauss-Seidel and Newton-Raphson iterative techniques for the analysis of normal operation or balanced faults as well as a non-iterative Z-bus technique for analysis of unbalanced or balanced faults.

Jan 1, 1980

The 107th Annual General Meeting of The South African Institute of Mining and Metallurgy was held at The Country Club, Johannesburg, Napier Road, Auckland Park on Wednesday, 11 August, 2004. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations, also to recipients of awards, senior members of industry, Honorary Life Fellows, past-presidents, our members and other guests, among them the following: Ralph Bagirathi, Executive Member, African Mining Association Rudi Rudolph, President, Association of Mine Managers of South Africa Andrew Whibley, President, Association of Mine Resident Engineers of South Africa Dr Con Fauconnier, President, Chamber of Mines of South Africa Nxolisi Diliza, Chief Executive Officer, Chamber of Mines of South Africa

Jan 1, 2004

By Bülent Erdem, Zekeriya Duran, Tuğba Doğan

The objective of this study was to evaluate the potential health risk associated with exposure of dozer operators to whole-body vibration. Measurements were made on 31 dozers used in different surface mines in Turkey. Predictions of adverse health effects of vibration were based on the standards BS 6841:1987, ISO 2631–1:1997, ISO 2631–5:2004, and the EU Vibration Directive:2002. Operators experienced high and comparable levels of vibration acceleration and dose during all dozer tasks: pushing the material (DOZE), moving forward (FORWARD), moving backward (REVERSE), and ripping (RIP). Specifically, DOZE, FORWARD, REVERSE, and RIP showed high potential of adverse health effects in terms of vibration dose according to the worst-case axis and vector sum criteria and a moderate adverse health effect for acceleration according to the worst-case axis criterion. Operators of large dozers were exposed to lower levels of vibration. However, no statistically significant relationship between vibration exposure levels and the propelling mechanism and the service time of dozers, operator experience, operator age, and ground type was found.

Jun 16, 2022

By D. A. Spencer, L. J. Gardner

In light of the apparent productivity benefits provided by mechanised stoping, Impala Platinum Limited commissioned a study to investigate its possible implementation for mining reserves located 1200 – 1700 m below surface. This paper records the methodology employed for designing a support system for such mechanised mining, as well as initial conclusions of the work done. Preliminary results show the concept to be technically feasible; work was however stopped due to financial non-viability. En considération des bénéfices de production apparents que donne l’exploitation par gradins mécanisée, Impala Platinum Limited a commissionné une étude visant à examiner sa mise en œuvre possible pour des réserves minières situées à 1200 – 1700 m sous la surface. L’étude présente rapporte la méthodologie employée pour créer un système de support pour ce genre d’exploitation mécanisée, ainsi que les conclusions initiales de ce projet. Les résultats préliminaires montrent que le concept est techniquement faisable ; cependant le travail fut arrêté à cause de difficultés de rentabilité. Im Licht des offensichtlichen Produktivitätsnutzens auf Grund mechanisierten Stossbaus, kommissionierte Impala Platinum Limited eine Studie, die dessen mögliche Implementierung für den Abbau von Reserven 1200 - 1700 m unterhalb der Oberfläche untersuchen soll. Dieses Elaborat dokumentiert sowohl die Methode die für das Design eines Unterstützungssystems für eine derartige mechanisierte Abbauweise angewendet wird als auch die anfänglichen Konklusionen der geleisteten Arbeit. Anfängliche Resultate zeigen daß das Konzept technisch durchführbar ist; die Arbeit wurde jedoch wegen der finanziellen Nichtrealisierarkeit gestoppt.

Jan 1, 2003

This study of the tin-tungsten ore of the Shepherd and Murphy Mine, in central northern Tasmania, was originally undertaken at the request of the Moina Tungsten-Tin Mining Co., N.L., as part of the research programme of the Mineragraphic Investigations Section of the C.S.I.R.O. It is based on the examination of a suite of specimens supplied by the management, supplemented by a more extensive collection and observations made by the author during a short visit to the mine in October, 1956.The Shepherd and Murphy Mine is at Moina, 36 miles S.W. of Devonport and 22 miles from Sheffield, the nearest railway station. It was worked almost&#183; continuously from 1893 to 1919, when a fire destroyed the mill; to that date it had produced concentrates to the value of &#163;141,000. After a long period of idleness, the mine was re-opened by the present company, but it has been announced recently that unfavourable market conditions have again forced closure.GENERAL GEOLOGYThe mine is on a deeply dissected plateau, about 2,500 ft. above sea level; it lies between the Iris and the Forth Rivers, whose valleys are deep gorges cut to about 400 to 600 ft. above sea level. From Moina westwards to the Iris River, a limestone regarded as part of the Gordon River Group, of Ordovician age, conformably overlies a sandstone containing tubicolar casts which are circular in cross section, half an inch in diameter and up to two feet long, and which resemble marine worm burrows (Elliston, 1953).

Jan 1, 1958