Search Documents

By J. Moore, D. Gault, R. V. Lugn

Impact of small projectiles with velocities between 0.9 and 7.3 km per sec on basalt produce craters chiefly by the ejection of fragments. Weight-size distributions of the ejecta are linear for part of the size range of the fragments. Cumulative weight-size distributions of the ejecta from different craters vary because of erratic formation of large fragments and a large percentage of ejecta below 0.1 mm. In the range of velocities studied, the crater depth is approximately proportional to the 0.75 power of velocity of the projectile. This relationship may represent a transition regime between the fluid impact regime and the undeformed projectile impact regime. The volumes per unit of projectile energy of the craters produced are comparable to those reported for lower speed projectile impact and drill bits. An experimental investigation of projectile impact on rock is being conducted jointly by the Ames Research Center of the National Aeronautics and Space Administration and the U.S. Geological Survey. Projectiles are launched with light-gas guns at the Ballistics Range of the Ames Research Center. The craters and ejecta produced in these experiments are being studied by the U.S. Geological Survey. Steel, aluminum and polyethylene projectiles weighing from 0.25 to 0.015 g were accelerated to velocities of 0.88 km per sec (2,900 fps) to 7.3 km per sec (24,000 fps) with a light-gas gun, using hydrogen as the propellant medium. Projectiles impacted the targets normal to plane rock surfaces in an atmosphere of air with a nominal pressure of 25 to 50 mm of mercury. The metal projectiles were mounted in supporting four-piece nylon sabots, which guided the projectiles down the launching tube. After launch, aerodynamic drag acted to separate the sabots from the projectiles. Impact velocities were determined with time measurements and spark photographs of the projectiles in flight. Ejecta were collected in lucite and aluminum containers placed around the target block. A small hole in the containers permitted projectile entry. Impact of projectiles of the size employed produced craters in the rock targets chiefly by ejection of fragments. The craters are small, roughly conical depressions with crushed and intensely fractured rock at the bottoms of the depressions. The ejecta are composed of pieces of the projectile and rock fragments ranging in size from a few tenths of a micron or less to several centimeters in maximum dimension. In this paper, the structural features of the craters, the weight-size distributions of the recovered ejecta, and crater depth and crater volume relationships are described. DESCRIPTION OF CRATERS Typical craters (Fig. 1) produced by experimental projectile impact in basalt are shallow, wide base

Jan 1, 1963

By Robert McClure, Frederic Leclercq, Ricardo Chavez

With significant vibration control and fragmentation challenges facing them, the CBS quarry (department of the Nord) successfully integrated a technical partner and mine to mill optimisation to deal with a difficult environment. For the last three years, CBS has been conducting a global production monitoring program similar to the mine to mill concept used in the mining industry. This concept consists of optimising the drilling and blasting while monitoring the effects on the downstream chain (vibration control, loading, hauling, crushing, plant output). Blast optimization is ensured by systematic control of the blast geometry (volumes, patterns, bench and face anomalies, drill deviation) and by the use of constant specific energy blasting. Constant specific energy optimises the work of the explosive in a blasting operation and, when combined with a high accuracy programmable electronic blasting system, reduces the impact of blasting on the environment and enhances blast performance. These techniques ensure consistent blasting results and hence improved site productivity. The improvements achieved have been identified thanks to an effective system designed to monitor the key production parameters.

Jan 1, 2007

By William H. Snyer

A relatively inexpensive, very fast response photo-optic/fiberoptic system has been conceived, constructed and employed by Denver Research Institute (DRI) to measure charge breakout uniformity on the surface of a very large ANFO detonation. The new equipment and technique was coined OWL (observation without leads). Its unique design provides the ability to monitor or measure detonation velocities and/or detonation breakout characteristics without fiberoptic or any other direct contact with the explosive. This system has proven to be versatile and has been used to measure surface breakout simultaneity on large ANFO detonations, munition case breakout times and velocity of detonation (VOD).

Jan 1, 1990

By Christine Hansen

?Kiss my Asteroid? Unofficial Title Human life is tied to minerals It?s worth noting that: The living human body consumes minerals. The minerals we take in multivitamins show the close linkage between human beings and mineral resources. Unlike tourism or specialized manufacturing, a human being could not live without mineral consumption. Minerals and their consumption is a tangible part of human life.

May 1, 2013

By David H. Browne

(Pittsburg Meeting, March, 1910.) NICKEL has always been a fruitful mother of problems. Previous to the year 1906 nickel was regarded as an element replacing iron in copper-mattes, and it was believed that the same laws which governed the elimination of iron could be applied-to nickel. This conception has lately undergone a complete change, and nickel in all its stages is now regarded as an element replacing copper; in other words, copper-nickel is considered now as two elements, but as one metal. When we commenced our investigations on Monel metal we made a great many experiments on the conversion of mattes, both high copper and high nickel. We studied closely the composition of the mattes and the changes produced by the blow. We found in all cases certain agreements which we believe are due to some law. Briefly stated, our conclusions are as follows 1. Nickel is not an element replacing iron in matte. 2. Nickel-copper alloys act in the matte-blow like one metal. 3. Nickel-copper alloys follow, during the matte-blow, exactly the same laws as govern. the behavior of copper alone. This brings up the question : What are the laws governing the production of metallic copper, and what are the relations copper to sulphur and iron during the Bessemer blow ?

Apr 1, 1910

By A. K. Raji, E. F. Orumwense, M. O. Ojumu

The Fourth Industrial Revolution has driven significant advancements in autonomous robotic systems, particularly in subsea exploration and offshore mineral dredging. This review examines the latest developments in electrically powered quadrotor-track subsea robotic crawlers, highlighting their potential to enhance efficiency, mobility, and adaptability in challenging underwater environments. The integration of advanced automation, artificial intelligence, and real-time control systems has paved the way for more effective robotic solutions in offshore mining. This study explores the dynamic performance of hydraulic crawlers to quadrotortrack robotic dredgers, focusing on their propulsion, navigation, and stability under high hydrodynamic conditions. By leveraging state-of-the-art technologies such as lithium-ion battery power systems, intelligent microprocessors, and sensor-based control mechanisms, these robotic crawlers offer a promising alternative to conventional subsea excavation methods. Furthermore, the review analyses recent experimental and simulation-based studies that assess the feasibility and performance of these systems in real-world applications. The findings of this review provide valuable insights into the role of 4IR in transforming subsea robotics for offshore mineral dredging. By addressing existing limitations and identifying key technological advancements, this study contributes to the ongoing development of nextgeneration robotic systems capable of operating efficiently in extreme underwater conditions

Jan 30, 2026

By J P. Sykes, A Trench

"The common-held view of the future of copper mining is one of declining quality of mineral resources and increasingly limited long-term development options. This decline, in turn, is viewed as inevitably leading to increasing economic, socio-political and environmental costs. As a result, new technologies and innovations will be required to mitigate cost escalation. The future is therefore typically summarised as a battle of a ‘below-ground’ declining quality asset base pushing costs upward versus ‘above-ground’ technology and innovation driving costs downward. The role that high quality new mineral discoveries could play in mitigating industry cost pressures is typically understated, if considered at all. New high quality discoveries can be mined at lower cost than existing assets and potentially if discovered in the right locations within a more amenable contemporary environmental and socio-political setting. Such deposits, once discovered, would improve the overall quality of the industry asset base, as well as benefitting their owners substantially through higher margins. However, to target new high quality deposits explorers need some understanding of the nature of high quality copper mines in the long-term future. Conventional scientific and economic techniques for analysing the future of copper supply, generally by studying the project pipeline, ignore as yet undiscovered resources and also struggle to fully incorporate the multiple internal and external factors that could impact upon copper mining practices in the future.Scenario analysis is specifically designed to consider multiple factors interacting in the future, and is thus more creative than simply looking at the visible project pipeline. The use of scenarios is therefore potentially capable of providing insight into aspects of the future of copper mining about which little is currently known or that remains considerably uncertain. In this study, the Oxford University Scenarios methodology was employed to analyse different plausible futures for copper mining and the consequent implications for exploration targeting strategies. The scenario analysis highlights two key dimensions or axes that serve to map out potential industry futures: firstly the technical and economic optimisation of the existing industry; and secondly the generation of new prospects or ‘search space’ for the copper industry. These two axes in turn frame four different scenarios for the future of the copper mining industry. These copper mining scenarios are then compared to the 20 largest existing copper mines and projects, and their owners, to determine if any represent an appropriately robust exploration targeting proxy: none do. The paper therefore concludes that efforts by industry are required to generate mine concepts that would be viable across all scenarios, and thus act also as exploration targeting proxies. In the interim, companies will have to seek to build portfolios that create an overall robust asset base, out of individually less robust assets. Failure to do this implies that consequential, irreversible strategic decisions lie ahead for the copper mining industry, which may be a threat to both incumbents and the very industry itself. This situation makes strategic exploration targeting in the copper industry very difficult.CITATION:Sykes, J P and Trench, A, 2016. Using scenarios to investigate the long-term future of copper mining and guide exploration targeting strategies, in Proceedings International Mine Management Conference, pp 265-290 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 22, 2016

By Arthur Notman

For the period January 1st, 1942, to January 1st, 1946, the American Bureau of Metal Statistics records the gold production of the world as 118,788,000 fine ounces. If we include 1946 at the same rate as 1945 (26,- 590,000), we arrive at a total of 145,378,000 fine ounces in the past five years . Included in these figures are estimates of Russian output at 4,000,000 ounces per annum for the five years, and 1,300,000 ounces per annum for Korea and Japan. The remaining 120,000,000 ounces represent the aggregate production from official reports of the other gold producing areas of the world, with the exception of the 1946 figures, as noted above. At $35.00 per fine ounce, this represents $5,188,230,000. According to the reports of the Federal Reserve System of the United States, on December 31st, 1941, the monetary gold reserves of the United States were $22,736,- 600,000 (at $35.00 per fine ounce) , while on October 31st, 1946 (latest available) , they had fallen to $20,402,000,000, a decline of $2,334,600,000. Adding this decline to the value of the new production for the five years, we have a total of $7,522,830,000, which has been absorbed by the rest of the world since Pearl Harbour, a rate of absorption of over $1,500,000,000 per annum. This has taken place at a rime when the advocates of purely managed currencies had convinced many people that gold performed no really essential function in the world's economy, and that we could get along perfectly well without it. It was pointed out that gold could not be eaten, it could not clothe our nakedness, it could not shelter us from storms, and, therefore, it was a non-essential, even though it could be used to settle international balances of trade. Apparently, the world as a whole still regards it as preferable to the paper promises of governments, however sound, relatively, they may appear. Actually, we have no way of measuring the true strength of this feeling, because the principal governments of the world have made it legally impossible for their citizens to own gold, except in the form of ornaments.

Jan 1, 1947

R. W. Raymond, New York, N. Y,:—Since the presentation of my note on this subject at the New York Meeting, Professor Louis has pointed out an error in my statement of his conception of " pitch "—namely, he understands the pitch, in the restricted sense which he proposes, to be the angle of inclination of the axis of an ore-body, measured on the vertical plane drawn through the body; whereas, I represented him as proposing to define " pitch " as the angle of inclination of an oblique body, measured on the plane of the dip, in the direction of the strike. The difference will appear upon consideration of the accompanying isometric projection, Fig. 1, in which ABCD represents the plane of the inclosing ore-deposit (vein or bed), and AC the axis of the oblique ore-shoot. ABE is the angle of the dip, as universally understood; and ACE

Jan 1, 1909

By S. Kouniali

Experience with knowledge-based systems for Layout planning and roadway support dimensioning is on hand in European coal mining since 1985. The systems SOUT (support choice and dimensioning, 1989), SOUT 2, PLANANK (planning of bolt-support), EXOS (layout planning diagnosis. 1994), Sout 3 (1995) have been developed in close cooperation by CdF1. INERIS2. EMN3 (France) and RAG 4, DMT5, TH - Aachen6 (Germany); ISLSP (Integrated Software for Layout and support planning) development is in progress (completion scheduled for July 1996). This new software technology in combination with conventional programming systems. numerical models and existing databases turned out to be suited for setting-up an intelligent decision aid for layout and roadway support planning. The system enhances reliability of planning and optimises the safety-to-cost ratio for ? deformation forecast for roadways in seam and surrounding rocks, consideration of the general position of the roadway in the rock mass (zones of increased pressure, position of operating and mined panels). ? support dimensioning ? yielding arches, rigid arches, porch sets, rigid rings, yielding rings and bolting / shotcreting for drifts ? yielding arches, rigid arches and porch sets for roadways in seam ? bolt support for gateroads (assessment of exclusion criteria and calculation of the bolting pattern) ? bolting of face-end zones (feasibility and safety assessment, stability guarantee).

Jan 1, 1996

By Robert G. Bottge

The Bureau of Mines investigated the availability of the land in south-central Alaska for exploration and mineral development of locatable minerals under State or Federal laws. The land ownership for an area of nearly 72.5 million acres in south-central Alaska was divided into 3 availability categories and 15 subcategories. In July 1985, 31.0 million acres of the study area were available for mineral exploration and development, 6.2 million acres were available with restrictions, and 35.3 million acres were unavailable. About 23.6 million acres in the study area are underlain by mineral terranes. About 9.9 million of the 23.6 million acres are available for mineral entry, 2.4 million acres are available with restrictions, and 11.3 million acres are unavailable. While much of the land currently classified as unavailable will be reclassified once it is conveyed to the State or to Native corporations, about 22% of the unavailable lands underlain by mineral terranes are now Federal parks, preserves, wildlife refuges, wild and scenic rivers, and military lands, all of which are considered permanently unavailable for mineral exploration and development.

Jan 1, 1986

By E. P. Youngman

This paper presents one of a series of digests of foreign mining legis- ation and court decisions that is being prepared in advance of a generel report elative to the rights of American citizens to explore for minerals and to own nd operate mines in various foreign countries. This interpretation of the laws of Demark and her possessions, has been prepared entirely from answers made by Ernest L. Ives, American charge d'effaires, Copenhagen, to a questionnaire ini- isted by the United States Bureau of Mines and transmitted through the courtesy of the Department of State.

Jun 1, 1932

By W. Roy Dunbar

"The Porcupine area is in northern Ontario at the intersection of N. Lat. 48° 30' and 81° W. Long. It is 125 miles due north of the Sudbury nickel range. Practically all the mineral production of this area has come from the townships of Tisdale, Deloro, Whitney, and Ogden, in order of importance. The accompanying map of the Porcupine area and its extensions to the east and west (Fig. 4) has been included to show what I consider to be an essential objective of this paper, a perspective for exploration.The discovery of gold ore in the Porcupine area at such an early date resulted from the extension of the Temiskaming and Northern Ontario railway and exploratory survey lines north into unexplored territory, for the early history of Porcupine is inextricably tied to the exploration along Niven's survey lines and the extension of the railway north from Cobalt to Nellie Lake. The following are the more significant events leading to the discovery of gold in Porcupine.1896-E. M. Burwash, employed by the Ontario Bureau of Mines, examined the country along Niven's base line and noted quartz veins that carried traces of gold. He was attached to Niven's survey party.1899-The late W. A. Parks reported on the geology of the portage route from Mattagami river to Night Hawk lake, for the Ontario Bureau of Mines. He noted the occurrence of gold in quartz veins and reported “I regard the region south of the trail to Porcupine lake as giving promise to the prospector"". He also was attached to Niven's survey party.1901-Charles Camsell, while prospecting for the Algoma Central railway, did some work on a vein occurrence carrying low gold on ground now known to be part of the Hollinger mine (3).1907- Extension of the Temiskaming and Northern Ontario railway to Nellie Lake.1909- Bannerman followed up Indian story about occurrence of coal, and found iron formation. He remained to prospect and found the gold-bearing vein of the Scottish Ontario property."

Jan 1, 1954

Optimizing production scheduling in open pit mines is important for managing cash flows of mining operations. This paper describes a new, probabilistic, mixed integer programming (MIP) formulation which has been developed to minimize the risk of not achieving planned production targets, in terms of metal production and ore tonnage feed for the mill during production, while considering maximization of total discounted economic value. The new MIP model also recognizes that to minimize movement of excavators over long distances and accommodate equipment access, the blocks scheduled for mining within a period cannot be spread too widely. The model is applied to a laterite nickel-cobalt deposit, as an example of multi-element deposits that have complex ore quality constraints. The results show that the proposed model generates feasible schedules. When compared with traditional optimization techniques, the new model is superior in terms of minimizing the risk of not meeting production targets, especially at the early stages of production, and in terms of generating practical scheduling patterns.

Jan 1, 2006

By Charles J. Kucera

Today's highly publicized issues of resource development and environmental protection are not new. But recently these issues have been played one against the other, and some would have us believe they are mutually exclusive. Why? Because modern man has realized that the shortest route to achieving economic progress is to subdue nature. He extracts mineral resources from the earth to provide the raw materials upon which other processes and services are based. But often in his search for economic progress he finds that other highly- held values (e.g., an unspoiled environment) have been violated. The natural response is a counter action - to attempt to protect nature. But this response is basically unsatisfactory because it is reactive.

Jan 1, 1979

By Lawrence H. Van Vlack, Alfred S. Keh

The distribution of sulfur in iron was found to be dependent upon the time and temperature of the treatment as well as the chemical composition of the sulfide. With higher temperatures, the sulfide phase spreads more extensively between the iron grains. A complete network, however, does not form until approximately 1300°C (2372°F), ot which temperature the dihedral angle approaches zero. Silicon has little effect on this change. Aluminum, oxygen, and manganese all modify the temperature of sulfide network formation to a higher value. The microstructures which result and have significance in relation to hot-shortness are discussed. SULFIDE inclusions in steel were recognized by metallurgists before the turn of the century. Considerable attention has been paid to them, and numerous studies have been made on the working properties of steel as affected by them. It has been suggested that ho t-shortness of steel is due to the presence of an enveloping liquid sulfide film at the grain boundaries of the steel in the range of the hot-working temperatures. However, several facts have been observed in commercial steels which do not seem to be completely consistent with this explanation: 1) the frequent absence of continuous films of sulfide as observed under the microscope, 2) the absence of hot-shortness in some high sulfur and resulfurized steels, and 3) the limitation of hot-shortness to a definite temperature range. The role that manganese plays in steel to eliminate hot-shortness is well known, but the theory behind it is still under question. Moreover, the effect of de-oxidizers such as aluminum and silicon, and the effect of oxygen are still not clearly known. In this study, the effect of heat treatments and of additions of manganese, aluminum, silicon, and oxygen upon the distribution of sulfide inclusions in iron was investigated. Both the as-cast and the heat treated structures were studied, using microscopic and autoradiographic techniques. Part of the results were interpreted in terms of Smith's' concept of microstructure. Review of Literature Metallurgists used to consider sulfide inclusions as suspended particles. It was Wohrman' who first pointed out that sulfide inclusions are soluble in liquid iron. Many observed facts may be understood on the basis of this concept of solubility. Wohrman found that small castings contain small inclusions. and larger castings contain larger ones. Also, inclusion sizes are smaller near the chilled surface. For the same size ingot, the average inclusion size in a given heat of steel depends upon the rate of solidification. That is, with slow solidification, enough time for precipitation and agglomeration of these

Jan 1, 1957

By J. S. UNGER

A LARGE proportion of the coke used is made in the by-product oven from the high-volatile coals mined in the adjacent district. At the beginning it was feared good by-product blast-furnace coke could not be made with our coals. By experimenting with various mixtures of coals, coking time, oven design, and coking temperatures, much has already been accomplished. The results show that a hard, dense coke, not easily broken by handling, can be produced. In its present state it is not all that could be desired, but it is being constantly improved. Such coke has been used alone as the fuel on several of the blast furnaces producing the highest daily production in the Pittsburgh district. Many of the coals in the Pittsburgh district when coked in the by-product oven yield a gas which contains a high percentage of sulfur, which is objection- able for many metallurgical operations. As this fuel is gradually replacing the ideal fuel, natural gas, which is becoming less plentiful, studies are being made of the best methods for purification. Some metallurgists believe sulfur to be a very injurious element in steel. Recent investigations by Government bureaus, scientific bodies and private firms, seem to indicate that a reasonable amount of sulfur may exist in steel without detriment. Without wishing to provoke any metallurgical controversy on the subject of sulfur, the fact remains that the daily purification

Jan 1, 1926

By Mario Aiezza

This paper outlines the results of a relationship developed during the design and construction of the foundations for the Gallery Towers project in Melbourne. Both the builder and the piling contractor were determined to arrive at a satisfactory foundation solution to the problems encountered at the site. The scope of piling work was to provide load-bearing piles under the building columns, some of which were located within a retention system that also required a piling solution. Geological conditions were variable and challenging. The site area was small and located adjacent to the National Arts Centre in the developed Southbank area, a high density office area. This presented logistical problems in limiting construction traffic on site and also demanding minimal noise and vibration emanating from piling activities. The piling contractor, Vibro-Pile, and the builder, Walter Construction Group, faced the challenges presented with a refreshing cooperative attitude that was beneficial to both companies. Commercial issues rising from design and construction problems were first put apart in order to allow the respective technical department of each company to work with minimum constraints to achieve the most cost effective solution. In the process usual adversarial attitudes resulting in loss of time and money was avoided. A number of issues were addressed successfully at minimum cost and time during this contract. Despite the difficulties encountered, the job was completed on time and with negligible claims for extras, resulting in the development of a strong mutual respect between both companies.

Jan 1, 2002

By Matthew Preedy, Brett Campbell, Jim Rush, Alan Howard, Derek Penrice

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. If such services are required, the assistance of an appropriate professional should be sought. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of the authors and are not necessarily those of SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2018

By Basil B. Zavoico

The production of all Russian fields incressed from approsimatctly 74,000,000 bbl. during 1926-27, to approximately 83,000,000 bbl. during 1927-28. Of this amount Baku was responsible for 54,.500,000 bbl., Grozny for 25,800,000 bbl., and Emba for 1,200,000 bbl. Accordingly, the proportional importance of the Grozny oil field has been considerably increased, the present production being twice that of 1913. The most notable factor of production during 1927-28 was the importance of gushers; 40.8 per cent. of the total was thus obtained. In the Baku fields 26 per cent. of the total, and in Grozny 74.2 percent'. of the total were produced by naturally flowing wells. This may be explained by the reduction in authorizations for drilling by the central authorities, and, accordingly, the local trusts increased the production to the planned figures at the expense of the proved prolific reserves. In Baku region, the Surnkany oil field produced 36.1 per cent. of the total Baku production, or an equivalent of 53,800 bbl. per clay, the largest percentage coining from the fifth horizon. Nest year's plans call for continual development of that horizon as well as of the sixteenth horizon in the Bibi-Eibat field, which was opened lately. In the Grozny fields the New Area (Bellik) WAS responsible for 79.4 per cent. of the total production. The authorized plan for 1928-29 production calls for 92,200,000 bid., and a reasonably accurate estimate for 1932--33 production is placed at. 156,000,000 bbl., with Baku contributing 101,800,000 bbl., Grozny 44,100,000 bbl., Emba 6,200,000 bbl., Kuban 2,100,000 bbl., Saghalien Island 1,400,000 bbl., and Russian Turkestan 400,000 bbl. In connection with recent discoverices in the Baku area these figures art. quite conservative. The average production per well per day in the Baku oil fields was 49.2 bbl., in Grozny 175 bbl.; in detail, Surakany oil field averaged 250 bbl., and the New Area in Grozny 514 bbl. per day. New completions in all Baku fields averaged 264 bbl. per day, and in Grozny 970 bbl. pel. day. These figures show a considerable progress in the technical developnlent of all fields, compared even with the prerevolution figures, since all the mprovements are noted in the fields that arc over 30 years old.

Jan 1, 1929