Search Documents

By Katsuyoshi Kondoh

The synthesis processing of Mg2Si or Mg2SiIMgO at lower temperature from the elemental magnesium alloy powder/chips and Si or SiO2 powder mixture was established via the repeated plastic working (RPW) based on Powder Metallurgy (PIM) process. RPW is much effective on the mechanical breakage of MgO surface films, which prevent from the solid-state reaction between Mg and Si powder. The solid-state synthesized Mg2Si particle of 200nm-2um is extremely fine, compared to that via the conventional casting process, causing the coarse one of 50-100um. This is because of not coarsening during the solid-state synthesis of Mg2Si. By using in-situ fonning process of Mg2Si via RPW and pre-heating before hot working such as extrusion and forging, the magnesium composite material with Mg2Si or Mg2Si/MgO dispersions was developed in employing Si or SiO2 particles, respectively. For example, when employing AZ31 chips as raw materials of the matrix, it has low density of 1.85g/cm3 and extremely superior mechanical properties, such as tensile strength over 350MPa with 5-10% elongation and Young's modulus of 47-50GPa, to the conventional Mg-Al-Zn alloys. The Mg composite alloy wires and pipes were produced via the hot extrusion process in the manufacturing plant, and also showed excellent mechanical properties.

Jan 1, 2003

By Katsuyoshi Kondoh

The synthesis processing of Mg2Si or Mg2Si/MgO at lower temperature from the elemental magnesium alloy powder/chips and Si or SiO2 powder mixture was established via the repeated plastic working (RPW) based on Powder Metallurgy (P/M) process. RPW is much effective on the mechanical breakage of MgO surface films, which prevent from the solid-state reaction between Mg and Si powder. The solid-state synthesized Mg2Si particle of 200nm-2JIm is extremely fine, compared to that via the conventional casting process, causing the coarse one of 50-100um. This is because of not coarsening during the solid-state synthesis of Mg2Si. By using in-situ forming process of Mg2Si via RPW and pre-heating before hot working such as extrusion and forging, the magnesium composite material with Mg2Si or Mg2Si/MgO dispersions was developed in employing Si or SiO2 particles, respectively. For example, when employing AZ31 chips as raw materials of the matrix, it has low density of 1.85g/cm) and extremely superior mechanical properties, such as tensile strength over 350MPa with 5-10% elongation and Young's modulus of 47-50GPa, to the conventional Mg-Al-Zn alloys. The Mg composite alloy wires and pipes were produced via the hot extrusion process in the manufacturing plant, and also showed excellent mechanical properties.

Jan 1, 2003

By S. G. Kumar, R. G. Reddy

"Niobium aluminides offer the advantage of higher high temperature capability compared to other intermetallic aluminides due to the refractory nature of niobium. However, the reaction sequence in Nb-Al system is sluggish and currently there is a great interest in the processing aspects of these materials. In the present study, a systematic investigation was undertaken to compare the effect of different powder metallurgy processing routes on the phase relations and microstructure of 66Nb-22AH2Ti (in atom percent) alloy. The three different process routes adopted were: (i) cold pressing followed by reaction sintering; (ii) cold pressing and hot pressing followed by sintering; and (iii) arc melting, hydride-dehydride process to make the alloy powder followed by cold pressing and then sintering. The samples are analyzed by XRD, Optical Microscopy, SEM-EDS and EPMA. The analysis showed that alloy pellets made from pre-alloyed powders i.e., arc melting followed by hydride-dehydride process, gave good densification and more Nb3Al formation.1. IntroductionTo improve the performance standards of turbine engines, materials scientists are challenged to develop materials that have· high thrust-to-weight ratio with high specific strength, high specific modulus and good environmental properties at elevated temperatures. The conventional high temperature materials like nickel based superalloys are high in density and hence many of the high temperature materials scientists have focussed their attention on intermetallic aluminides like Fe-AI, Nb-AI, Ni-AI and Ti-AI in recent years. The phase relations and properties of alloys based on Fe-AI, Ni-AI and Ti-AI are fairly well known whereas little is known about the alloys based on niobium aluminides."

Jan 1, 1996

By John T. Berry, Robert D. Pehlke, Michael J. Beffel

"Pattern making and metal casting organizations are currently adopting CAD/CAM systems and implementing this technology in design and production. Al though significant progress has been reported, these systems generally are based on two or two and one half dimensional analyses. Very few are based on solid geometric modelers.The present paper emphasizes the need for solid geometric modeling of the casting and rigging system and linkage with a solidification simulator. The nature of some of the technological challenges which have slowed this development are discussed, including accurate description of complex surfaces and their intersections and the bridging of computer encoded information with NC technologies and with FEM-based simulators for stress and thermal analyses. A recently prepared modular-structured FEM simulation code implemented on a micro computer is described.Construction of a solid geometric model of the casting and rigging and validation of the combination for optimum characteristics of soundness, quality and yield by solidification simulation are I inked as key elements in the foundry of the future. Data base support for this CAD/CAM system is rapidly being developed throughout the world.INTRODUCTIONThe simulation of shaped casting solidification using the digital computer, goes back to at least the early nineteen-sixties when Forsund (1) in Denmark applied the technique to the problems of casting surface quality.Prior to that time, the work of Paschkis and co-workers using the analog computer ranges back to the nineteen-forties, when work sponsored by the AFS Heat Transfer Committee at Columbia University revealed many hitherto unknown or only partly anticipated aspects of casting solidification (2).Three reviews of the various historical aspects of simulation should be referenced. Firstly, the AFS monograph by one of the present writers (RDP) and his colleagues - describing background and later work, again sponsored by the AFS Heat Transfer Committee at the University of Michigan (3). Secondly, a review prepared by Durham and Berry (4) which discusses broad aspects of casting solidification simulation. Thirdly, a review by Erickson (5) which contains an excellent bibliography to 1980. In addition to these papers, the publications lists of the CADCAST project* and the proceedings of the two Engineering Foundation Conferences of Casting and Welding Modeling, published by ASME, are also most notable (6) •"

Jan 1, 1986

By R. S. Celmer

The distributions of cobalt, molybdenum, copper, and selenium between nickel matte and silica-saturated iron silicate slag have been determined in the region of the metallic saturation boundary, at 1523 K. Results are given as a function of the composition of the coexisting Fe-Ni alloy and the activity of iron in the system. Under strongly reducing conditions, these minor elements display a marked preferential accumulation in the sulphide phase. It is shown that the dissolution of cobalt and molybdenum in slag follows an oxidative mechanism, and distribution equilibria are correlated with the oxygen potential. From these data, the thermodynamic properties of cobalt in nickel matte are computed. Further, comparisons of minor element partitions are made between the nickel and copper matte smelting cases under metal saturation conditions.

Jan 1, 1988

By Travis Knight

Mixed uranium and refractory metal carbide systems have been proposed for space nuclear power and propulsion applications. Solid-core space nuclear reactors could be utilized for low- earth-orbit (LEO) to geosynchronous-earth-orbit (GEO) transfers, manned missions to the moon or mars, and orbiter missions to the outer planets. However, these high performance space nuclear reactors present some challenging materials engineering requirements for operating in a high temperature, high radiation, and hot hydrogen environment. Since the RoverNERVA programs were concluded in 1973, significant advances in ultrahigh temperature materials technology have been made which can be applied to the development of an advanced solid-core nuclear fuel. Nuclear thermal propulsion (NTP) was first studied in the U.S. beginning in the mid-1950's during the RoverNERVA programs. During that time, about 20 rocket reactors were built and tested. More recently, Russian nuclear rocket reactor tests with pseudo-ternary carbide nuclear fuels (U, Zr, Nb)C and (U, Zr, Ta)C have been operated at temperatures as high as 3300 K for one hour. This study examined the processing parameters for fabricating the pseudo-ternary carbide, (U, Zr, Nb)C.

Jan 1, 1999

By X. Jay Gao

A fast high-temperature carburizing process integrated with materials design and optimization via a systems design approach was developed to significantly reduce process cycle time. Process experiments were focused on boost cycles to obtain a robust boost process and investigate surface reaction kinetics, primary carbide formation and dissolution. Weight gain and microhardness were measured, all showing evidence of non-monotonic time evolution for longer boost times at higher temperatures. Optical and electron microscopy and other techniques have been used to identify possible carbides, their location and types. These results assist the picking of first boost time with least variation rate in terms of content of case carbon and carbides, dissolvable in subsequent diffuse if any. The results also provide critical information to properly formulate surface reaction kinetics and diffusion and formation kinetics of carbides modeled using DICTRA. Keywords: high temperature vacuum carburizing, partial pressure carburizing, heat treatment, process development, carbide, case hardening, microstructural analysis, over carburizing

Jan 1, 2003

By Felipe Costa Hashimoto Bertin, Jorge Alberto Soares Tenório, Rodrigo de Souza Dalti Pereira, Denise Crocce Romano Espinosa

"The increasing amount of portable devices and their fast obsolescence generates an increasing quantity of discarded batteries. The recycling process of discarded batteries allows the recovery of metals for further use and avoids the contamination of soil and water. Even though there are several researches on the topic, few papers focus on mixed batteries. The purpose of this work is to characterize a mass of collected mixed batteries and study the hydrometallurgical process of recycling. The specific leaching parameters studied were pH, temperature and reduction potential. The specific goal was testing the selectivity of pH for leaching each metal. The results show that the optimal leaching occurs in acid solutions with negative pH at IM of sulfuric acid and at room temperature (25°C).IntroductionThe increasing portability of electronic devices in the past century along with their fast obsolescence produce tons of discarded materials yearly that could be recycled generating new materials for the industry. For example, metals such as cobalt and nickel, that are worth respectively US$ 30.00 and US$ 16.10 per kilogram[l,2] are disposed in urban trash yearly, which means that millions of dollars are thrown away instead of being recovered and reused[3].Besides the obvious fact that the society is throwing money away, most of these metals are toxic for the environment and all mammals, so when badly stored after use they can be found contaminating ground water which will contaminate the entire lifecycle. Some of these metals can cause cancer, serious lung problems and have bioaccumulative properties [4] resulting in lower productions of natural products and maybe death for consumers.So in compliance to new regulations such as the National Solid Residue Politic (PNRS) and the CONAMA-Resolution N°401 from November of 2008[5]- (that follows similar restrictions and regulations as the European directives) all those urban and electronic wastes need to be correctly disposed and treated before being thrown away on local dump sites.In Brazil the national rate of garbage recovery is around 70%, which only 5% is properly recycled, accordingly to the research of the UFSC, also electronic waste grows at 5% per year [6]The present study was motivated by the fact that recycling processes for batteries are not spread through the country and by the fact that most papers do not try to recycle a mixed mass of batteries, but a specific mixture which does not represent the composition of traditional household wastes."

Jan 1, 2014

By M. J. Collins

Direct pressure leaching of zinc sulphide concentrates was started? commercially in October 1980. Continuing research and development studies at Sherritt and feasibility studies for a number of clients have defined various pressure leach configurations for integrattons with existing roast- 1 each operations and for grass roots plants. Existing and potential applications of zinc pressure leaching are discussed.

Jan 1, 1990

By Klaus Bauckhage

Phase-Doppler-anemometry (PDA)-measurements have to be taken from representative measuring positions from inside the spray cone, helping - with the support of simulated data of improved process models - to describe the multiphase flow situations within the spray cone - and accordingly to that - the heat transfer conditions for the rapid cooling and (partly) solidifying melt droplets before their impact onto the substratddeposit. Simulations and PDA-measurements thus give the base to confirm the hypothesis of the existence of a semisolid mixed-layer and it's influence on the resulting material structure during compaction. The dispersed particles in the spray cone exhibit a cooling and solidification process within a split of a second, which leads - as far as the particles solidify - to a dendritic structure with very short dendritic arm spacings. This causes within the particles extremely short distances for the following equalizing diffision processes taking place on a high temperature level (between liquidus and solidus) in the semisolid mixed-layer of the deposit and explaining the short residence times within this zone of only seconds up to a few minutes. This and the fact that the globular structure of the mushy zone (in the semisolid mixed-layer) leads to an unidirectional crystallization process over very short distances also explains the chemical and morphological ,homogeneity of the sprayed material. The dynamics of these process steps, the very special buffer function of the mixing layer during parameter variations as well as the controlled cooling process of the preform in order to avoid hot cracks influence the quality of the material. Due to the necessity of measuring and controlling the particle bound mass-, momentum- and enthalpy- fluxes to the deposit the PDA-technique has been adapted and modified in order to receive in-line and (in the future) also on-line data from the dynamics of the multiphase flow conditions within the spray chamber.

Jan 1, 1999

By Sergio N. Monteiro

Polymeric matrix composites reinforced with coir fibers are being used in many industrial applications such as automobile interior panels and cushions. These composites have relatively low mechanical strength due to the weak fiber/matrix interface. The objective of the present work was to investigate the effect of a surface alkali treatment of the curaua fiber on the mechanical behavior of polyester composites with different amounts of these fibers. The treatment, also known as mercerization, was performed with distinct concentrations, 0.1 and 10% of NaOH at 1 min and 1 hour, before incorporation of the coir fibers into the polyester composite. The results showed no significant change in comparison to similar untreated coir fiber composites. A microstructure analysis revealed that, in addition to reducing the hydrophilic characteristic of the fiber,the treatment also affects the surface morphology and impairs the fiber/matrix interfacial strength.

Jan 1, 2009

By Kimberly Conner-Mills

Due to increasingly stringent worldwide environmental regulations for gaseous, aqueous and solid waste emissions, conventional smelting technology cannot effectively process arsenic containing materials. Many globally significant copper properties have copper sulfide mineralogy that has a high arsenic content present as enargite with significant contained precious metals. As global copper, silver and gold demand increases while significant world resources decrease, treatment of sulfide orebodies with enargite is becoming increasingly important. Methods to selectively dissolve and fix arsenic, leaving behind clean copper and precious metals-bearing concentrates could effectively treat these ores.

By Wu Liu

A modified falling ball technique for measuring the viscosity of liquids is described. It consists of recording the weight vs. time of a crucible holding the liquid of unknown viscosity, as a solid ball, or liquid drop, is let to fall through the liquid. This method does not require measurements at constant terminal velocity, as the conventional falling ball technique. Also, measurements do not depend on visual observation, which is not possible in opaque liquids or containers. The effect of process parameters on the utility of this method and its potential application to liquid systems of metallurgical interest were analyzed theoretically. The paper also com- pares the gravimetric method to the conventional falling ball technique for measuring viscosity.

Jan 1, 1992

By Masahiro Yoshimura, Sergiy Korablov

"Hydi-othermal corrosion ofTiN, TlAlN and CrN PVD films (3 µm thick) deposited on SUS-304 substrate was studied in 100MPa water in 20-950°C temperature range up , to 750h. The beginning temperature of their reaction was determined as 200°c for TiN and TiAlN and 500°C for CrN films, which are quite low in comparison with that of air oxidation of those powders. Very thin oxide scales. of TinO; n-I homologous series phases were formed above 300°C. TiO2 anatare. is observed for TIN and TiAlN films at 400°C. The· feature of hydrothermal corrosion of CrN films seems to be CrNxOy phase formation.Distinguishable weight changes were observed at higher temperature than 700°C for TiN, 750°C for· TiAlN and 800°C for CrN respectively. Hydrothermal corrosion kinetics .was constructed to calculate the activation energy of hydrothermal corrosions. On the base of obtained data, hydrothermal corrosion resistance was as follows: TiN – TiAlN - CrN. Facetted oxide crystals were formed at higher temperature than 500°C for TiN, TiAlN and 850°C forCrN.IntroductionThe metallic nitride (TiN; TiAlN, CrN) PVD films have high hardness, strength and wear resistance. Therefore these films are widely used in industry for wear resistij.nce application such as cutting tools and die molds. Their performances depend on not only the mechanical properties but also corrosion resistance of coated films. High temperature oxidation of metalliq nitride and nitride films was well studied [1-5]. However there are no reliable data concerning the .corrosion resistance of coated nitride materials. In high-temperature and high-pressure water. There are a few reports on hydrothermal corrosion of nitride films [6,7]. The increase of corrosion resistance of CVD films was observed in following succession TiC - TiCNO - TiCN - TiN at 300-680°C temperature interval and I 00 MPa pressure water according to data of the first report. Kawana et al. [7] have reported about excellent corrosion resistance of CrN films under 290°C and 8, 6 MPa water during I 000 h in the circulating type experimental loop. The films thickness was about 7-10 µm in both cases. However it remains unclear the chemical state of the surface species and especially in-depth distribution, oxide scale thickness and its growth, and defects formation in the oxide film."

Jan 1, 2000

By T. Asahina, M. Nakamura, M. Mabuchi, I. Shigematsu, M. Nakanishi, G. Yamauchi

"Commercial stainless steels (SUS304L and SUS430) were subjected to equal channel angular extrusion (ECAE) at room temperature to a total strain of 2.3 to 9.2. For each type of stainless steel, it was shown that the sample processed by ECAE showed higher room temperature strength than the as-quenched sample. This is probably due to the heavily worked structure. On the other hand, both strength and elongation of the ECAE processed SUS430 were increased by annealing at 773K. It is likely that higher strength is attributed to both the heavily worked structure and fine substructures. It is also likely that higher elongation is attributed to the fine substructures. It is concluded that ECAE is available for improving the room temperature strength of commercial stainless steels.INTRODUCTIONEqual channel angular extrusion ( ECAE ) is a technique that provides the repetitive deformation and allows to high intensity of deformation. With this procedure, a sample is pressed through a channel that has an equal cross section but bent at an angle of ?> [1-2]. Shear strain is introduced when a sample passes through the bending point of the channel. Repetitive processing is feasible because the cross-sectional dimension of a sample has no change during processing. To date, many reports have described that ECAE is available for the fabrication of fine-grained materials [3-14]. On the other hand, an ECAE processed sample can achieve high intensity of deformation through repetitive deformation. According to the equation given by Segal [ 2 ], a strain of about 1 is introduced in each pass through die if the angle ? is 90 deg.It is well known that high tensile strength can be achieved in metallic materials through work hardening [15]. It is also known that metallic materials with fine grain size show high strength [16]. Hence, it is expected that ECAE is available for strengthening method in metallic materials. In the present paper, we will report the mechanical properties of stainless steels processed by ECAE. As samples, SUS304L austenite stainless steel and SUS430 ferritic stainless steel were chosen. Each alloy has a single-phase structure (fee or bee) and shows no phase transformation, so that transformation strengthening cannot be applied. Hence, a heavy cold work such as ECAE may be effective for strengthening of this stainless steel. Annealing was conducted for the ECAE processed SUS430 to vary its microstructure. Then, the effect of annealing on the strength of the ECAE processed SUS430 was also investigated."

Jan 1, 2000

By Pandey H. D.

The paper describes a fluidised bed ion exchange method for simultaneous removal of phenols and cyanide from the effluent. Use of an eluant enables regeneration of the resin in the continuous operation mode. The breakthrough experiments conducted both on the laboratory scale and on a pilot plant scale have shown that while the level of phenol can be brought down from 462 ppm to about 6 ppm, the free cyanide is almost totally removed. An examination of data indicates that the method can serve the twin objectives of pollution control and phenolic compounds recovery.

Jan 1, 1992

By Helvio P. G. Santafé Jr., Ruben J. S. Rodriguez, Sergio N. Monteiro, Teresa E. Castillo

"The coir fiber extracted from the husk of the coconut fruits are worldwide available in tropical regions as a low cost lignocellulosic by-product for many applications including composite filler in automobile parts. Possible uses above room temperature require information on the thermal behavior of these coir fiber composites. Therefore, the objective of this work was to perform thermogravimetric, TGA and DTG, analysis on polyester matrix composites incorporated with different volume fractions of coir fiber. In general, it was found that thermal degradation associated with weight loss occurred in three stages. Changes were also observed in the DTG peaks that could be attributed to the coir fiber participation through the decomposition of its lignocellulosic structure.IntroductionThe development of new materials has always been motivated by the need of improved properties. This was the case of modem composites with combination of properties that surpass those of conventional monolithic metallic alloys, ceramic or polymers, from which composites are made. A typical example is the synthetic fiber reinforced composite with specific strength i. e, ultimate stress divided by density, higher than any other monolithic material. Today, however, our global society is concerned with serious environmental problems and thus demanding that new materials be developed with distinct characteristics. They are known as environmentally correct and are expected to be sustainable, which corresponds to the condition of being biodegradable, renewable, recyclable and neutral with respect to C02 emission, considered the main responsible for global warning [1]. Synthetic fiber composites cannot meet these requirements. Consequently, new composite reinforced with cellulose-based natural fiber are being developed [2-8] and are already replacing the synthetic ones in several engineering fields including the automobile industry [9-11]. These composites have additional advantages owing to the lignocellulosic fiber benefits of being diversified, abundant, less expensive, lighter and of societal interest [8]. In some cases even technical advantages such as non-abrasive effect to processing equipments and more flexibility exist in comparison to synthetic fibers."

Jan 1, 2011

By José Antonio, Silva Souza, Luis Alves Venancio, Emanuel Negrão Macedo, Antonio Ernandes M. Paiva

"The production of alumina from bauxite using the Bayer process generate 1.25 ton of the residue known by red mud and 460 kg of CO2 per ton of alumina.The direct use of exhaust gases from the alumina refineries to react and neutralize the bauxite residue may allow a double gain: open a wide range of new applications for bauxite residue reducing the reactivity of red mud and sequester approximately 15% or 67 kg of CO2 per ton of alumina.This paper shows the reaction of a suspension of bauxite residue-water with a simulation of the calcinator exhaust gases of the refinery. The influence of the temperature and the ratio water red mud is also analyzed.2 IntroductionThe production of millions of tons per year of alumina around the world generates around 1.25 tones of the residue known as red mud and 0.4 ton of CO2 per ton of alumina . The vast majority of the red mud is stored in large sealed lakes. Due to the high reactivity is considered dangerous and currently there is no operating process capable of reuse all the material at any refinery. These lakes after filled of solid material eventually have the surface revegetated. Otherwise will need monitoring for decades and remain as an environmental passive. The search of a industrial process that combine the reduction of the CO2 emission and the reduction the pH of the red mud opening the possibility of use in large scale in a economically viable way is the main objective of this work.The use of the exhaust gases of the refineries to neutralize the bauxite residue may allow a double gain: Open a large array of new applications for the residue with the reduction of its reactivity and sequester million of tones of CO2 plus other gases like SO2 [7] and NOx.This project main objective is to study the reaction of the CO2 with the Bayer process residue in order to obtain the basic parameters to design an equipment capable of process this reaction on a pilot scale. With this objective compositions of red mud on spray were processed with flow of gas containing CO2 at different temperatures and with concentration similar to the exhaust gases of the calcination process of the refineries. With the results, basic concepts of a pilot scale equipment were evaluated.A revision of the work already done on this type of residue were done [3, 9, 10]. Alternatives and potential barriers on chemistry and environmental fields were discussed. With the objective of industrial application the potential use of these materials were evaluated through the pH control, mass balance and x-ray diffraction."

Jan 1, 2010

By Akita Ito, Sumio Kato, Mikio Sugai, Shinichi Nakata

"Spark Plasma Sintering (SPS) is a newly developed method for the sintering of metal and ceramic powders, and completes their densification at low temperature and in short period. The SiC powder was synthesized from diatomite and graphite or carbon black by heating at 1 450°C for 1 hr in an argon atmosphere. The synthesized SiC powder was heated at 1500-1800°C, 50 MPa for 15-18 min by SPS. The relative density of sintered SiC body increased with the rise in the temperature. The oxidation of the surface of the SiC particle and impurities in SiC from diatomite greatly influenced the sintering promotion of SPS.IntroductionThe SiC has high hardness because of the covalent bonding, and is also excellent in thermal and chemical stability. However, it is difficult to obtain a dense SiC sintered body by the combustion heating-method. Therefore, the dense SiC bodies have been made by the use of additives and I or the hot pressing (HP) method.In this study, the SiC powder was synthesized by using diatomite of natural products and graphite, and carbon black of reagent as raw materials, and the relationship between the properties of SiC powders prepared at various synthetic conditions and the density of sintered body by SPS was examined."

Jan 1, 2000

By Wanderson Silva Rodrigues, Paulo Adão Marinho dos Santos, José Antonio Silva Souza, Luis Alves Venancio, Emanuel Negrão Macedo

"1 AbstractThe production of alumina from bauxite using the Bayer process generates 0.7 to 2.0 ton of the residue known as red mud per ton of alumina. This material has no large scale current use and is usually stored. This paper shows that it can be used in a suspension with water as a gas effluent cleaner with high efficiency to remove SO2. It can substitute other materials currently used reducing the overall environmental impact and potentially reducing the cost of gas treatment.2 IntroductionThe production of millions of tons per year of alumina around the world generates from 0.7 to 2.0 ton of the residue known as red mud per ton of alumina. The vast majority of the red mud is stored in large sealed lakes. Due to the high reactivity this material is considered dangerous and currently there is no operating process capable of reuse all the material produced at any refinery. These lakes after filled of solid material eventually have the surface revegetated. In any cases they will remain as an environmental passive and need monitoring for decades. The search of industrial processes that combine the cleaning of gas effluents emission and reuse of these residues can contribute to the reduction of the overall impact of the alumina production process.The main objective of this work is to study the efficiency of the red mud as alternative raw material for the control of emissions of SO2 in combustion gases. Usually this is made through alkaline solutions of CaCO3 or NaOH in absorbing equipments like spray towers or packed column. This project main objective is to study the reaction of the SO2 with a suspension of red mud and water in order to obtain the basic parameters to design equipment capable of process this reaction on a pilot scale. With that goal compositions of red mud on spray were processed with flow of gas containing SO2 with concentration similar to the exhaust gases of the combustion process of the refineries."

Jan 1, 2011