Search Documents

By B. R. Westphal

The Integral Fast Reactor (IFR) concept being developed by Argonne National Laboratory is based on the pyrometallurgical processing of spent nuclear metallic fuel with subsequent fabrication into new reactor fuel by an injection casting process. During fabrication, a dilute scrap stream containing uranium alloy fines and broken quartz (Vycor) molds is produced. Waste characterization of this stream, developed by using present operating data and chemical analysis, was used to evaluate different uranium recovery methods and possible process variations for the return of the recovered metal. Two methods, comminution with size separation and electrostatic separation, have been tested and can successfully recover over 94% of the metal. Recycling the recovered metal to the injection casting process was evaluated for the different economic and process impacts. The physical waste parameters and the important separation process variables are discussed relative to their effects on the viability of recycling the material. A discussion of the criteria that is being used to establish the acceptable operating limits is also presented.

Jan 1, 1992

By Do-Hyeong Kim, Jong-Jin Pak, Jung-Mock Jang, Min-Kyu Paek

"Thermodynamic relations among Mn, Al and N in liquid iron were studied by measuring the effect of Mn on the solubility product of AlN in liquid Fe-Mn-Al-N alloys in the temperature range from 1773 to 1873 K. The critical Al and N contents for AlN formation were determined by the metal-nitride-gas equilibration technique over wide ranges of melt composition and temperature. The effects of Mn on N solubility in Fe-Mn and Fe-Mn-Al melts containing Mn up to 26 mass% were separately determined in the same temperature range. The experimental results were thermodynamically analyzed using the Wagner's formalism to estimate the critical Al and N contents for the onset of A1N formation. The validity was checked by the observation of inclusion evolution in Fe-20%Mn-1.5%Al-0.6%C-0.3%Si-0.012%N melt during cooling and solidification.IntroductionRecently, high manganese steels such as Twinning Induced Plasticity (TWIP) steels have been developed as next generation steels because of their high formability as well as excellent strength and ductility.[1•2l In these steel grades, a large amount of Mn (15-20 mass%) and Al (1-2 mass%) are added to liquid steels, and such high Mn and Al concentration bring the great challenges to the steelmaking and casting processes. Mn significantly increases the N solubility in liquid iron and the AlN inclusions can be easily formed at such high Al concentrations due to high affinity of Al and Mn with N in liquid steels. Although the AlN inclusion is known to be a dominating and considered as a detrimental phase for the hot ductility of steels,l3l thermodynamics of AlN formation in high Mn-Al alloyed liquid steels was not well known.Moreover, the melting point of these steels decreases down to near 1623 K as increasing Mn content up to 20 mass%. However, most of thermodynamic data has been measured at the steelmaking temperature around 1873 K. Even at steelmaking temperature, there are huge scatters in thermodynamic interactions of Mn and Al on N in liquid iron. The nitrogen solubility in Fe-Mn alloy melts has been measured using the Sieverts' method[4l and the samplinij method[5-7J in the temperature range of 1813 to 1973 K. In the authors' recent study,[8•9 the N solubility in Fe-Al alloy melts was measured using the sampling method in the temperature range of 1823 to 1973 K. However, the simultaneous effect of Mn and Al at high concentrations on Nin liquid Fe-Mn-Al-N alloys is still not known. Also, there remains uncertainty about the temperature dependence of the interaction parameter of Mn on N in liquid Fe-Mn alloys. Therefore, it is worthwhile to check the temperature dependence of this parameter at a low temperature near the melting point of Fe-Mn alloys. There have been few studies on the characterization of non-metallic"

Jan 1, 2014

By F. E. Pawlek

Copper concentrates can be comminuted in an attritor within a very short time to a particle size of 1 - 0.1 um. Addition of sodium hydroxide enhances commninution. The concentrates, suspended only in water, can be completely dissolved under oxygen over pressure and temperatures ranging from 120 - 180°C (248 - 356°F), because the surface area of the concentrate has been significantly increased by the ultra fine grinding. Addi¬tion of a small amount of silver ions to leach liquor containing sulfuric acid acted as a catalyst for the dissolution of chalcopyrite, because of the formation of local elements on the surface. The addition of C1- ions was also catalytically very effective. With this method it is possible to completely dissolve the copper contained in chalcopyrite concentrates after ultra fine grinding within 30 min at 110°C (230°F) under an oxygen partial pressure of 1 atm (14 psig). Several flowsheets demonstrate the industrial feasibility.

Jan 1, 1976

By Jun Li, Lingling Zhang, Daqiang Cang, Guizhou Zhao

Pilot trial of direct modification of molten blast furnace slag and production of high acidity coefficient slag wool fibers were investigated nearby a blast furnace. Molten blast furnace slag discharged from blast furnace and then directly flow into specialized modification furnace and quartz was simultaneously added into the molten slag as modification agent. The modified molten slag was electric heated to 1500–1550 °C and then the melt was produced into slag wool fibers through high-speed centrifugation method. Melt with acidity coefficient of 1.2, 1.4, 1.6 and 1.8 were investigated and fibers with corresponding acidity coefficient were produced. Slag wool fibers with shot content of 5.5, 5.8, 6.2, 6.8% and average diameter of 4.5, 4.9, 5.6, 6.4 lm for four samples were successfully produced, respectively. Total energy consumption and production costs decreased by 50–70% compared to traditional cupola furnace method. This method provides an energy-saving and emission-reduction technology for the direct utilization of molten blast furnace slag.

Mar 1, 2018

By Yue Yu, Hangyu Zhu, Jianli Li, Di Wang

Thestainlesssteelslagastheby-productofsteel-makingplantscontains 2–10 wt% Cr O , and the potential elution of hexavalent chromium impedes the 2 3 utilization as a secondary resource. The reduction of chromium oxide in steel- making slag containing Cr O by FeSi at 1550 °C was investigated in the labora- 2 3 tory. The experiments were performed in a carbon-tube furnace, and the samples collected during tests were analyzed using X Ray Fluorescence (XRF) and Scanning Electron Microscope (SEM) equipped Energy Dispersive Spectroscopy (EDS). The results show that the FeSi addition could efficiently enhance the reductionandrecoveryofchromium.WhentheamountofFeSirangedfrom2upto 9 wt%,therecoveryincreasedfrom65.60%to84.19%.Theoccurrenceofresidual chromium was metal particles, which dispersedly distributed in silicate phases owing to the size limitation. The sufficient FeSi could easily reduce chromium oxidesintometal,butthecriticalfactorofchromiumrecoveryistheprecipitationof suspending metal particles from the molten slag. Thus, some measures should be proposed in order to make sure that the suspending particles are adequate to aggregate into bigger ones. (cid:1) (cid:1) (cid:1) (cid:1)

Mar 1, 2018

By Michal Stepien, Piotr Palimaka, Stanislaw Pietrzyk

During the steel scrap melting process in an electric arc furnaces, the generated dust may contain a significant amount of zinc. The content of zinc in case of melting galvanized steel scrap is variable and ranges from 15 to 40 wt%. This dust cannot be re-used for the steelmaking process. On the other hand the zinc content is too low to treat the steel dust as a feedstock in pyrometallurgy of zinc. When they are disposed in land fills they have adversely effect the environment. This work presents selected results of research and development of new technology, which was developed in order to utilization steelmaking dust in the sintering process. One of the products (zinc-rich) can be used as a high-quality raw material for production of zinc by pyro- or hydrometallurgical processes. The second one product from the shaft furnace can be used as a feedstock for the steelmaking process.

Mar 1, 2017

By Zemin Ma

A novel chromate [Cr(VI)] reducing bacterium was isolated from chromite ore processing residue disposal site of China and identified as a Leucobacter sp. by 16S rRNA gene sequence homology. The minimum inhibitory concentration of strain CRB1 was 820 mg l-1 of Cr(VI). The reduction of Cr(VI) occurred only under aerobic conditions. With an initial concentration of 2.5×108 cells ml-1, 1800 mg l-1 of Cr(VI) was reduced entirely within 38 h under the optimum conditions, at 30 °C and pH 9.0. Increasing Cr(VI) concentrations prolonged reduction process and higher cell densities meant quicker reduction. A blue precipitate was produced during chromate reduction of strain CRB1, which was binding to the surface of bacterial cells and determined as trivalent chromium with electron paramagnetic resonance (EPR) spectrometry. The conspicuous chromate reduction ability of Leucobacter sp. CRB1 suggested a potential for bioremediation of Cr(VI) containing wastes.

Jan 1, 2008

By L. M. Luckevich

Gypsum is a product from the neutralization of sulfuric acid by lime or limestone. This paper will discuss specifications for gypsum used in wallboard, cement and agriculture and the factors affecting its utilization potential. Process conditions during the neutralization which enhance or inhibit utilization potential will be included. In addition, this paper provides a technical and economic perspective of the gypsum industry in North America with a view to the factors affecting the utilization of synthetic gypsum in traditional applications. Current production and consumption of natural and synthetic gypsum in Nonh America are described and the impact of their differences on utilization options are discussed.

Jan 1, 1996

By Dieter Neuschiitz, Pengfu Tan

"In order to understand the sintering phenomena during iron ore sintering process, a CFD model of iron ore sintering has been developed, combining with the kinetics of 15 relevant chemical reactions with the aim of describing the temperature fields and the gas flow patterns in the sintering bed. This CFD model can be used to simulate the concentrations of the gaseous and solid species, temperatures of the gas and solid, melting and molten fractions of the mixture, gas velocities, temperature zones and residence times of the gas in each temperature zone. IntroductionThe off-gas analyses clearly revealed that the off-gas of a sinter strand does not have a composition corresponding to thermodynamic equilibrium, for example, the CO, CO2 and O2 concentrations are not the mutually consistent equilibrium values. Apparently the chemical reactions in the sinter bed are controlled kinetically. Therefore kinetic modeling of sintering reactions combined with CFD modeling is necessary to understand the sintering phenomena during iron ore sintering process.Several models of iron ore sintering have been developed since 1970 [l-l 4l, each being more refined than its predecessor. The models were formulated as a series of differential equations to describe chemical and physical changes occurring at a point in the bed. These equations were solved numerically in a vertical plane along the strand. The present CFD model, based on the Nath's model [14], has been published in the reference [15]. In this work, some new chemical kinetic models of gas-solid reactions are incorporated in the present CFD model. The concentrations of gaseous and solid species, temperatures of gas and solid, melting and molten fractions of solid, velocity of gas, and residence time of gas in each combustion zone can be calculated by this model."

Jan 1, 2004

By S. N. Monteiro, L. G. Pedroti, D. P. Santos, M. S. Peixoto, G. C. Xavier

The Baixada Campista is a region located in the municipality of Campos dos Goytacazes and is known as an important pole producing ceramic artifacts in Brazil. The clay used in this production is usually extracted from different layers of the region itself undergoing a pretreatment process. The objective of this work was to characterize the different soils (A, B and C), from different layers of the reservoir, in order to characterize the different physical and chemical characteristics (granulometry, determination of Atterberg limits, moisture and chemical analysis). To optimize, using the simplex methodology, properties such as mechanical strength, porosity and linear retraction. The results pointed to an optimum proportion of the clays studied so that the properties meet the Brazilian technical norms, being the proportion of 30% of soil A, 30% of soil B and 40% of soil C well.

Mar 1, 2018

By F. Kongoli

Viscosity is an important parameter of copper smelting and converting processes. It affects the settling of matte or metal droplets in the slag, distribution of elements etc. Despite this importance, confusion exists on the viscosity of copper smelting slags as a result of disagreements found among the measured viscosity data of several authors especially in the slags of high ferric iron content and close to magnetite precipitation. In this work a critical review of the existing data on the viscosity of copper smelting slags has been first carried out and the effect of oxygen potential on the viscosity of copper smelting slags has been clarified through a coupled quantification of viscosity and liquidus temperature. The confusion in the literature has been clarified and the importance of the relation between the viscosity and the liquidus temperature is discussed.

Jan 1, 2003

By T. Nagano

Mitsubishi Metal Corporation started the development work of a new process for continuous production of copper in 1961. After a series of experimental and semi-commercial operations, the first commercial plant of the Mitsubishi Continuous Copper Smelting and Converting Process was put into operation in March, 1974. The new plant, which has a design capacity of 4,000 metric ton copper per month, was built within the premises of Naoshima Smelter, replacing the old No.1 reverberatory smelter there. The SO2-rich exhaust gas from this new plant is blended with the off-gas of the No.2 reverberatory furnace for production of sulfuric acid and the overall emission of sulfur at Naoshima has been greatly reduced. The operation of the continuous plant has been satisfactory and several advantageous features of the Mitsubishi Process have been proven on a commercial scale. This paper first gives a brief description of the history of the development work and the characteristic features of the process. The paper then describes the new commercial plant and operating data obtained so far.

Jan 1, 1976

By Zhengde Pang, Xue-wei Lv, Guibao Qiu, Chenguang Bai, Zhiming Yan

As a result of the consumption and the rising cost of raw materials for ironmaking, steel producers have increased their utilization of low-cost, low-grade raw materials such as high alumina iron ore. The effect of Al2O3 and the Al2O3/SiO2 ratio on the viscosity, surface tension and sulfide capacity of the CaO–SiO2–Al2O3–MgO–TiO2 blast furnace slag system were studied in the present work. At a fixed CaO/SiO2 ratio of 1.20, 9 mass pct MgO, and 1 mass pct TiO2, the viscosity increases with an increase in Al2O3 content at a range of 16–24 mass pct, and decreases when the Al2O3 is higher than 24 mass pct. Increasing Al2O3/SiO2 from 0.47 to 0.92 causes a slight decrease in viscosity of the slags and has an opposite effect when Al 2O3/SiO2 is more than 0.92. The surface tension increases with increasing Al2O3 content at a fixed Al2O3 content and Al2O3/SiO2 at a fixed CaO content. The desulfurizing capacity decreases with increasing of Al2O3 content, while increases with increasing Al2O3/SiO2 at a fixed CaO content.

Mar 1, 2018

By Ling-yun Yi, Yuan-bo Zhang, Bing Hu, Zhu-Cheng Huang, Zhen-yuan Liao

"Nucleation and growth mechanism of iron crystal grain in coal-based shaft furnace direct reduction process by microwave heating were investigated by optical microscope, scanning electron microscope and EDX. The results indicate that microwave has selectivity on various minerals which absorb microwaves. The high temperature in certain area of pellets and thermal stress on the interface of minerals are formed, results in the wustite grain smashed along the joints, and iron crystal grains turned out a spherical shape obviously. The iron crystal nucleus is formed firstly at the edge of wustite, on the interface between grains and in the holes in pellets, and grows gradually while reduction carries on from surface layer to inner core. Microwave heating promotes the rate of transportation and accumulation of the iron crystal grain, increases growth rate of iron crystal grain and contributes to formation of dense iron-jointed crystal texture eventually.IntroductionMicrowave energy as a new energy, which selectively heating materials through internal energy dissipation, has the advantages of heating uniformity, high thermal efficiency, fast heating, clean and pollution-free compared to conventional heating motheds. Microwave energy also has obvious superiority in increasing productivity. Thus, it has been widely used in many areas, including electronics, food processing, chemical, medicine, environmental protection, and family life etc [1]. As a rapidly developed green metallurgical method, microwave heating also has been widely recognized by areas of grinding, pretreatment, pre-reduction, drying, furnacing, metal extraction, and waste materials processing and utilization. Some research achievements are gradually putting into practice, showing great potential in chemical and metallurgical industry [2-3]."

Jan 1, 2011

By G. Barbery

The models for particle composition prediction that have been put forward are limited to simple textures and lead to an independance of grade with respect to particle size in broken ore. A presentation is made of a modification in texture description; binary textures, in which each subeonstituent has its own breakage characteristics are introduced. The calibration of the textural model can be made using heavy liquid separation results. The application to the case of coal is presented. Coal washability data present spe¬cial difficulty due to the distribution in the specific gravity of coal, which must be taken into account. Coal s.g. distribution is taken as a generalized exponential distribution. Model calibration is then possible and is shown to be in good agreement with experimental data.

Jan 1, 1987

By Guohua Bai, Lin Zhang, Shan He, Xuling Chen, Min Gan, Xiaohui Fan, Yanbin Tang

"For reducing the dust content in flue gas during copper smelting in the Ausmelt, technologies and mechanism of strengthening the pelletizing of copper concentrate were studied. The results show that adding bentonite, organic binder or composite binder can effectively enhance the strength of green pellet and reduce the rate of shedding powder in drying process, and composite binder works best. When adding 1 % of composite binder, the drop strength of green pellet increased from 1.9 times/P to 4.5 times/P, the rate of damage dropping from 2 m reduced from 50.12% to 13.08% and the rate of shedding powder reduced from 60.28% to 25.13% at drying temperature of 400111. In addition, the mechanism of binder absorbed in the surface of mineral was investigated by infrared spectroscopy. The results showed that composite binder absorbed in the surface of copper concentrate was in the form of chemisorptions, which made hydrophilic enhanced, while bentonite absorbed in the surface of copper concentrate was physisorption.IntroductionWith the technologies of copper smelting developing, the equipment of copper smelting steps into a large-scale and efficient level in recent years. As Ausmelt smelting is characterized by being efficient, environmentally-friendly and energy-saving, it is generally recognized by the enterprises of copper smelting [l]. The process of Ausmelt smelting starts with materials mixing, and then pelletizing. From this point onwards, pelletized balls are charged to the top of the furnace, undergoing drying and smelting reaction[2]. Since copper concentrate is fine-grained, directly adding into smelting furnace can make it blown out of the furnace together with the airflow upwards, rendering flue gas high in flue dust, which can cause the loss of concentrate greatly, and make smelting environment poor as well. The concentrate transported into the furnace and smelted after disc balling is conducive to improve the capacity of melting furnace during copper concentrate smelting, reduce the powder shedding rate and improve enterprise benefits."

Jan 1, 2013

By Bin Xu, Qian Li, Yong-bin Yang, Xiao-liang Liu, Tao Jiang, Yan Zhang

Some high sulfur and arsenic-bearing gold concentrate has a gold leaching rate less than 80% by oxidation roasting-pickling-cyanidation process. The characteristics and intensification of gold leaching were studied systemically. By combining chemical composition and phase analysis, the low gold leaching rate was found to lie in the capsulation of gold by iron-containing phases including iron oxides, arsenopyrite and pyrite. 96.66% of gold in the industrial leaching residue was capsulated and 95.88% of the capsulated turned out to be in the iron-containing phases. The results of laboratory pickling-cyanidation experiments on the calcine and industrial leaching residue presented further demonstration for the fact that gold capsulated in the iron-containing phases was hard to be leached. However, the gold cyanide leaching rate of calcine could be raised over 95% by a reduction roasting-pickling pretreatment which played such a significant role in exposing the capsulated gold that gold leaching was intensified remarkably.

Jan 1, 2015

By A. Arenas-Flores, Pandiyan Thangarasu, J. P. Hernández-Lara, F. R. Barrientos-Hernández, J. A. Romero-Serrano, A. Hernández-Ramírez, M. Pérez-Labra

BaTiO3 doped with Gd3+, was synthesized from BaCO3, TiO2, and Gd2O3 as powders using the solid state reaction method (Ba1-xGdxTi1-x/4O3). The milling of the precursors was performed in an agate mortar with acetone as control means and compositions x = 0.001, 0.005, 0.05, 0.15, 0.25, 0.35 Gd3+ (wt%). Firstly, the powder mixture was decarbonated at 900 °C for 8 h, after it was sintered at 1400 °C for 5 h. Tetragonality of synthesized BaTiO3 doped with Gd3+ was analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM) and Raman spectroscopy (RS). Subsequently, the powders sintered were uniaxially compacted cold until to obtain pellets of about 10 mm in diameter; which again were sintered at 1400 °C for 4 h. XRD patterns and Raman spectra results revealed that the crystal phase of the obtained particles was predominately tetragonal BaTiO3.

Mar 1, 2017

By R. Leiby

Prior to March 1992, the only component of the lead acid battery that was not recycled by East Penn Manufacturing Company was the sulfuric acid electrolyte. This acid was unusable in new batteries because the iron level was found to exceed new product specifications. The development of a liquid ion exchange process to remove the iron from the acid allows East Penn to currently recover over three million gallons of sulfuric acid annually. The process is based upon the use of an iron selective liquid ion exchange material or solvent to extract iron from the sulfuric acid electrolyte followed by regeneration of the solvent. Equilibrium and kinetic data for the extraction and regeneration steps were collected in order to scale up the process to commercial scale. An electrochemical process for the treatment of the acid used in the regeneration step was, also developed which significantly reduces the volume of strip acid required in the process.

Jan 1, 1995

By S. L. Pohlman

Physical characteristics of possible importance in the acid leaching of Chrysocolla have been evaluated. Surface area studies and pore size distribution indicate: 1) a large surface area (350 m /gm); 2) an average pore size of 13 or 16 Å , depending upon use of the adsorption, or desorption, branch of the Type IV isotherm in the evaluation; ) the presence of a significant fraction of pores of size less than 15 Å determined by the accumulation surface area method. The initial structure is micro- crystalline on the basis of x-ray powder patterns; the silica leach residue is amorphous and has only 24 m2 /gm surface area, and loses integrity when dry. However, readsorption of copper onto the wet leach residue gives a product with integrity and 100 m2 /gm surface area. Visual observation of the leach residues supports evidence of a non-protective diffusion mechanism of leaching which is well correlated by the shrinking core model previously presented.

Jan 1, 1976