Search Documents

By T. Fujita

The removal of phosphorus is essential 1n order to increase the recycling of steelmaking slags for their manganese, iron and lime contents. This study aims at establishing the phosphorus mineralogy and its distribution in steelmaking slags, the effect of slow cooling, and the methods of phosphorus removal. A series of steelmaking slag samples was prepared at different cooling rates, and the mineralogy, chemistry and grain size of the samples were investigated with SEM/EDS and x-ray diffraction. The test results using high gradient magnetic separation are discussed.

Jan 1, 1988

By Ivo André

Sorption of copper ions from aqueous solutions by dried biomass of the aquatic plant Potamogeton luscens was studied at laboratory scale. The aquatic plant was collected in water resources in Brazil, washed, dried at 60°C and ground in a bladed mixer. Sorption experiments were conducted in agitated flasks and in a packed bed column. Maximum copper removal was obtained between pH 5.0 and 6.6 when copper was present in the ionic form Cu'. Sorption followed the Langmuir isotherm with saturation attained at 35 mg/g. Free energy of sorption was found, to be of the order of -25 kJ/mol. Sorption kinetics data were better described by a second order reaction and rate constants were calculated in 0.030 1/(min.mg) for - 4.0 mm particles and 0.081 1/(min.mg) for - 0.59 mm particles. Removal of metal ions in a packed bed column showed that Potamogeton luscens biomass can be used in several sorption/dessorption cycles. After sorbent saturation, copper ions can be recovered from the loaded biomass by elution-with H2SO4, solution. Main mechanism responsible for heavy metal uptake was found to be ion exchange. Results are discussed in terms of the surface properties of the biomaterial, solution chemistry of copper ions and thermodynamics parameters.

Jan 1, 1995

By Xueming Lv, Xuewei Lv, Jie Qiu, Lunwei Wang

Non-isothermal multiple scanning rate analysis method was used to analyse the solid-state reduction of nickel laterite by carbon. According to the TG curves, the activation energies were calculated and the most probable mechanism functions were determined by the Malek method. The results show that the process can be divided into three stages according to the reaction degree (a): 0–40%, 40–70%, 70–100%, respectively. In the stage of 0 a 0.40, the most probable mechanism function fits the chemical reaction order function. In the stage of 0.40 a 0.70 and 0.70 a 1.0, the process may not be exactly described by one mechanism function.

Mar 1, 2017

By Vojteh Leskov?ek

The tribological load is the load on forging tools resulting from the relative motions between the plastically deformed workpiece and the die. In comparison to many other forming processes hot die forging has an especially disadvantageous tribological system. The advantages of the application of hard coatings, which are well known for cutting tools, are to a much lesser extent explored for casting, extrusion, molding and forging tools. Increasing the lifetime of these tools is an important task in surface engineering because of the complex loading conditions and often complicated tool geometry. The plasma-assisted chemical-vapor-deposition (PACVD) technique is well suited to depositing hard coatings onto large dies and molds. The aim of this study is to present and discus results obtained on a duplex PACVD hard coating in an industrial application like the hot forging of automotive parts. A new generation of vacuum-melted and remelted (VMR) hot-work tool steels has been developed; these can reach a hardness of 58 HRc, and have a fracture toughness at this hardness equivalent to that of standard hot-work tool steels at 45 HRc. This offers one of two advantages: the steels can be used at the higher hardness to provide resistance to wear or deformation, or, when used at a hardness of 47?49 HRc for hot forging, to provide temper resistance, nitriding behavior and adhesive wear resistance. The results presented here are from a preliminary investigation. The experimental results indicate that the introduction of a proper duplex PACVD hard coating will lead to an improved wear resistance and a longer lifetime for the hot-forging dies. Furthermore, by using a hard, low-friction coating excellent anti-sticking properties can be obtained. At this stage of the investigation it is also necessary to carry out pilot trials to determine the wear resistance and the tool life in practice.

Jan 1, 2006

By Leonardo Mota, Felipe Perissé Duarte Lopes, Marcelo Gomes da Silva, Sergio Neves Monteiro, Helion Vargas

"Natural fibers, as a class of material, are attracting the interest of engineering sectors owing to specific advantages such as comparatively reduced cost and lower density as well as environmental benefits associated with renewability and biodegradability. For industrial applications, thermal properties, among others, are required. These are major requirements, especially in the case of an insulating natural fiber. In the present work, thermal properties of the curaua were investigated by photothermal techniques, i.e., the open photoacoustic cell and a method based upon the monitoring of the temperature evolution as a function of time. This investigation, in tum, permitted to evaluate two important thermal properties: the thermal diffusivity and the specific heat capacity of the curaua fibers. Indirectly, by means of simple mathematical relations, the thermal conductivity was also obtained. The results were compared with other materials and characterize the curaua fiber as an efficient insulator.IntroductionMaterials are gaining attention in recent years owing to their benefits for the environment as compared to synthetics. Being biodegradable, yearly renewable and recyclable, the natural planted-based are considered fully sustainable [1]. In particular, their life-cycle, from growing to industrial processing, absorbs as much C02 as it is emitted and makes them neutral with respect to greenhouse gases responsible for global warming [2]. Typical examples of these environmentfriendly materials are the lignocellulosic fibers that have been used in simple items such as ropes, baskets, textile, modest roofing, etc, since the beginning of our civilization [3]. In the past few decades, these natural fibers have been extensively investigated [ 4-1 O] as a possible reinforcement phase of polymer composites in substitution for synthetic fibers. In fact, engineering application of lignocellulosic composites are today in the market, especially in the automobile industry [11-13]. Out of the hundreds available natural fibers, only part of them exhibits superior properties to be qualified for composite reinforcement."

Jan 1, 2011

By Katri Avarmaa

Aluminum and copper are large volume metals in electronic appliances, while tin and indium exist as common minor elements. All of these non-ferrous metals are aimed to be separated and recycled from the end-of-life electronics into non-ferrous scrap fraction(s), and further through pyrometallurgical and/or hydrometallurgical processes to pure metals. Depending on the mechanical pre-treatment processes, aluminum and copper liberation from each other varies. This study focuses on the influence of alumina on indium and tin distributions between copper alloy and iron silicate slags with 0, 9 and ∼16 wt% of Al2O3. The experiments were executed with an equilibration-quenching-EPMA technique in an oxygen pressure range of 10−10–10−5 atm at 1300 °C. The metal-slag distribution coefficient of indium remains constant as a function of alumina in slag, while that of tin increases. Therefore, aluminum in feed or alumina addition to the slag improves the recovery of tin into copper. Nevertheless, oxygen pressure has clearly more significant influence on the behavior of both the metals in the smelting conditions.

By Y. Z. Zhang

Cyanide has generated environmental concerns because of its toxicity, and it may not respond to the treatment of complex and refractory gold ores. Gold leaching by thiourea is one of the most promising substitutes of cyanide. However, the high reagent consumption has hindered thiourea from its commercial application in gold extraction. The process chemistry and mechanism of thiourea degradation has been discussed on the basis of chemical bonding theory, thermodynamics and electrochemistry in this paper. Progresses on the decreasing of thiourea consumption have been summarised. The potential application of thiourea in gold extraction has been evaluated.

Jan 1, 1996

By Finlay Campbell

Nickel laterite pressure acid leach plants and reduction roast plants have had a checkered history in their engineering, construction, startup and operational reliability. Many potential projects have been the subject of detailed studies over the last thirty to forty years but relatively few have advanced to commercial production. Four reduction roast plants are currently operating, an additional one was partially constructed but never completed, and another was started up in 1974 and shut down after 12 years operation. Three acid leach plants have been built and commissioned in the last five years, trying to follow the example of the Moa Nickel plant in Cuba. An additional acid leach plant project is currently on hold, following limited construction work, its future subject to review by the owner because of potential cost over-runs. This paper attempts to discuss difficulties that may be encountered as a project is developed and will address factors which may affect production ramp-up schedule, long term production performance and overall production success. Comparisons are made with ramp-up performance at other large metallurgical plants that employ some comparable unit operations. Keywords: Caron, PAL, nickel laterite ore, ramp-up, reliability, process development, equipment design, step-out, commissioning, startup.

Jan 1, 2004

By Pedro Henrique L. M. Lopes, Édio Pereira Lima Jr., Fernanda Santos da Luz, Fábio de Oliveira Braga, Sergio Neves Monteiro

Several works have been dedicated to study the ballistic response of multilayered armor systems (MAS), including those using natural fiber composites as second layer. These composites disclosed good ballistic performance, having economic and environmental advantages. In the present work, the objective was to investigate the effect of areal densities of each MAS layer, in the overall performance of a MAS with an alumina ceramic front, a curaua fabric reinforced composite filling, and an aluminum alloy backing the target. Ballistic “backface signature” tests were conducted, varying the areal densities of the MAS layers according to a Box-Behnken design. The results showed a similar influence of the ceramic and aluminum layers in the MAS “backface signatures”, although deformation and failure mechanisms were significantly different. The composite also showed significant participation in the overall MAS performance. Since the composite is cheaper and lighter, a balance minimizing the other layers would be advantageous.

Mar 1, 2018

By Vinicius Alves Gomes, Jean Igor Margem, Thallis Cordeiro, Frederico Muylaert Margem, Roberto Faria Jr., Sergio Neves Monteiro, Marina Rangel Margem

Natural fibers are attracting the interest of engineering sectors owing to specific advantages such as lightweight and lower cost as well as for their inherent condition of being renewable, biodegradable, recyclable and neutral with respect to CO2 emission. In particular, the fiber extracted from the malva plant stem is nowadays recognized as one of the strongest lignocellulosic fibers. However, the thermal properties of the malva fibers have yet not been fully investigated. The present work had as its objective to investigate, by photoacoustic spectroscopy and photothermal techniques the thermal properties of diffusivity, specific heat capacity and conductivity of a pressed malva fibers sample. The results revealed that these fibers showed a superior thermal insulation capacity.

Jan 1, 2015

By O. Forsén

A new cell construction was designed for the study of the electrochemical behaviour of additives in conditions that simulate real copper, electrorefining. The behaviour of gelatine and thiourea was studied by applying different electrochemical methods, i.e. polarization resistance and voltametric measurements. In this study, individual galvanostatic electrolysis experiments were carried out for 120 hours. The organic additives were introduced to the electrolyte at certain intervals and their concentration was varied in the range &om zero to four ppm. An optical microscope was applied for the examination of copper cathode deposit microstructures. The results show that gelatine has a polarizing effect on the deposition potential of copper whereas even small amounts of thiourea depolarize the electrodeposition of copper. The maximum inhibitor efficiency of gelatine was obtained at a gelatine concentration of slightly lower than two ppm. When both gelatine and thiourea were present in the electrolyte, the depolarizing effect of thiourea exceeded completely the polarizing effect of gelatine. If chloride ions were added to gelatine and thiourea containing electrolyte, the electrochemical behaviour of the system was altered drastically. Chloride ions resulted in the prevailing of polarization effect caused by gelatine while the depolarizing effect of thiourea disappeared in this system. The polarizing effect of gelatine increased until chloride ion concentration of 30 ppm was reached. Also, the above electrochemical phenomena could be detected in the optical examination of copper deposit microstructure.

Jan 1, 1995

By Mike Dry

Conventionally, lithium-bearing brines are processed via solar evaporation, chemical purification, and either electrolysis to lithium hydroxide or precipitation of lithium carbonate. Lithium-ion battery technology and electric vehicles are forecast to greatly increase the demand for lithium, but not all lithium-bearing brines are amenable to the conventional extraction process and new approaches are being developed. The chemistry associated with conventional lithium extraction is outlined and two new approaches are discussed.

By W. G. Davenport

Flash smelting is used. mainly for making molten Cu-rich matte* from fine Cu-Fe-S** flotation concentrates. It blows dried concentrate particles into a hot fumace, surrounds them with 01-rich gas and allows them to react. The results are: (a) partial oxidation of Fe and S from the concentrate (b) generation of heat (c) melting of the oxidized particles to form molten Cu-rich matte, ~65% Cu and Cu-barren slag, ~1 % Cu. The melted particles fall to the hearth of the flash furnace where they fonn matte and slag layers, The matte is tapped from the furnace and oxidation-converted to metallic copper. The slag is skimmed, treated for Cu recovery then stockpiled or sold. Figures 1.1 and 1.2 show industrial flash furnaces and the position of flash smelting in the coppermaking flowsheet. ,Fig. 1.3 shows the locations of flash furnaces around the world.

Jan 1, 2001

By Lucas L. da Costa, Sergio N. Monteiro, Romulo L. Loiola, Tammy G. Rodrigues Portela

"The fibers extracted from the petiole of the buriti palm tree are relatively strong as compared to other lignocelluloses fibers, with a potential for composite reinforcement. In this work, polyester matrix composites incorporated with these fibers were investigated for their flexural behavior. Specimens with up to 40% in volume of continuous and aligned buriti petiole fibers were bendtested until rupture. The results showed an increase in both the composite mechanical strength and the stiffness with incorporation of these fibers. A fractograph analysis by SEM disclosed a moderate adhesion mechanism between the buriti petiole fiber and the polyester matrix. This mechanism is apparently responsible for the improved performance of the composites.IntroductionIn recent years, the substitution of energy-intensive synthetic materials for natural ones is being considered in many industrial sectors including automobile, packing and textile [1]. A typical case is that of natural fibers, mainly those obtained from cellulose-based plants also known as lignocelluloses fibers. They have being investigated in the past two decades, aiming to replace synthetic fibers, particularly the glass fiber, commonly used as polymer composite reinforcement [2-8]. From the engineering point of view, lignocellulosic fibers present today important environmental, economical, societal and technological advantages already discussed [7-8]. Moreover, several lignocellulosic fibers are known since the beginning of our civilization and still cultivated or naturally extracted all over temperate and tropical regions of the world. According to Kalia et al [1 ], these fibers can be classified by their origin, as shown in Table 1."

Jan 1, 2011

By M. C. Furerstenau

Adsorption behavior of various surfactants on sulfide minerals is very much affected by the nature of the surface of the mineral. Since sulfides are naturally meta-stable, oxidation occurs when they are exposed to air, especially in aqueous environments. As a result. oxygen assumes a major role in sulfide flotation. Mechanisms of adsorption of various thiol collectors on sulfide minerals have been reviewed. The electrochemical behavior of various sulfide minerals has also been reviewed. Flotation behavior of galena, chalcocite, sphalerite, pyrite, chalcopyrite and pentlandite has been presented together with the. flotation of copper sulfide- nickel sulfide ore.

Jan 1, 1993

By Mehdi Asadi, Heinz Palkowski

"In recent years, the increased demand for advanced high-strength steels (AHSS) mainly had been driven by the need of the automotive industry to reduce weight and to improve safety. Beside good ductility and high strength, those steels have a high bake hardening (BH) effect, giving additional contribution to the strength of structural parts, subjected to the paint baking process. In this paper we concentrate results gained for hot rolled dual phase (DP) steels.For the simulation of changing process conditions within the final hot rolling the specimens were hot deformed using different schedules of temperatures and reductions, selected according to the non-recrystallization temperature (TnRX). It was possible to refine the DP steel structure by control-ling the deformation temperature and the amount of strain below TnRX during the thermo-mechanical controlled processing (TMCP). This structure refinement resulted in an improvement of the strength and BH behaviour. A wide spectrum of mechanical properties could be obtained depending on the different hot deformation schedules. The best strength and BH levels were recorded for the deformation below TnRX at the highest amount of strain.IntroductionDP steels are characterized by a good formability, high strength and a good compromise between strength and ductility [1]. Moreover, the DP steels exhibit a continuous yielding behaviour, low yield point and a high strain-hardening coefficient [2]. Furthermore, the DP steels often show a large potential for bake hardening (BH). BH refers to the increase in yield strength as a result of the paint baking treatment of the shaped auto-body parts. The primary mechanism that causes the additional strengthening is the immobilization of dislocations by the segregation of interstitial atoms, known as classical static strain aging [3]. The increase of strength thus achieved allows a further reduction of sheet thickness and improves the crash safety and the dent resistance. The BH of special steel qualities is technically used in DP, where e.g. the increase in strength is realized in the final heat treatment [4]. Previous own investigations [5-6] stated that the BH effect of DP is much stronger than that one for conventional BH steels."

Jan 1, 2012

By Dmitri Nassyrov, In-ho Jung

"All relevant thermodynamic and phase diagram data in the CaO-Fe10-CaF2 system were critically reviewed. One set of model parameters describing the Gibbs energy of all phases has been obtained as a result of critical evaluation of the available data and optimization of the model parameters. The Modified Quasichemical Model was used to describe the interactions in the liquid phase. All calculations were performed using the FactSage thermochemical software.IntroductionSlags contaimng CaF2 are of significant interest to the steelmaking community. Notable examples of slags containing significant amounts of CaF2 include Electro-slag Remelting (ESR) slags [1] and mould flux for continuous casting [2]. The role of these slags is, among other things, to refine steel by absorbing inclusions and dissolved impurities. During slag-steel interaction, some iron from the steel will inevitably get oxidized and form iron oxides which will dissolve into the slag. With this in mind, it is important to understand the interaction between CaF2 and Fe,0 for accurate prediction of slag composition and process optimization. A thermodynamic optimization of the CaO-FetO-CaF2 was thus undertaken."

Jan 1, 2013

By L. A. André Santos

Atmospheric processing of nickel lateritic ores with low costs has been encouraged. In this work the kinetic of atmospheric acid leaching of a northern- Brazilian ore with 1.63% Ni and large amount of fine particles (d50 ≈ 0.075 mm and 40% below 0.038 mm) is presented. Chemical analysis showed a trend of Ni and Fe concentration in finer fraction (−0.075 mm) and Si and Mg in the coarsest one (−0.500 + 0.150 mm) associated to distinct mineral phases. Nickel is widespread in the mineral matrix. Distinct behaviors were observed as a function of particle size associated to the distribution of silicates and iron oxides in the ore. The kinetic modeling indicated that leaching is controlled by porous layer diffusion at 65 °C, but at 95 °C exhibits a mixed control by porous layer diffusion in initial minutes (60 min) and by chemical reaction or diffusion through the pore layer in final minutes (60–240 min) depends on metal evaluated.

By G. E. S. Lima, I. K. R. Andrade, N. G. Viana, R. O. G. Martins, L. M. Sathler, L. G. Pedroti, C. M. M. E. Torres, W. E. H. Fernandes, C. M. Silva, M. A. Caetano

In Brazil, kraft pulp mills are rapidly expanding and industrial waste generation is increasing. Technical feasibility of using solid wastes from kraft pulp mills as raw material in other industries may be an interesting approach to manage environmental and economic aspects of the industry. This paper proposes the incorporation, in different proportions (0, 2.5, 5 and 7.5%), of alkaline solid wastes from pulp mills, namely dregs and grits, to clinker in the Portland cement industry. The research was carried out in two steps: (i) characterization of dregs, grits and clinker; (ii) laboratory testing (determination of soundness by the Le Chatelier method, determination of setting times, determination of water content of the paste with normal consistency, determination of compressive strength and static modulus of elasticity). The results showed that the addition of dregs and grits to the clinker up to 2.5% were feasible according to the Portland cement Brazilian standards.

Mar 1, 2017

By Bernd-Arno Behrens, Klaus-Georg Kosch

"In times of increasing energy costs automotive lightweight construction is gaining in importance. This paper deals with the production of hybrid steel-aluminum compounds by forging. The compound forging process is a promising method to successfully manufacture functional parts by applying resource-saving process steps. Nevertheless, challenges resulting from different material properties must be solved.The heating of hybrid material work pieces made of steel and aluminum is a great challenge. Steel is forged at a temperature of at least TSt =900 °C, while aluminum should not exceed a temperature of TA1= 500 °C. For achieving the required temperature gradient extensive experimental investigations have been carried out. Intermetallic phases form during the manufacturing process and can influence the bonding and the global part quality. In addition, methods for the characterization of the joining zone between the materials steel and aluminum are analyzed and the factors influencing the formation of intermetallic phases are determined experimentally.IntroductionIn times of increasing energy costs and stricter conditions relating to environmental protection, automotive lightweight construction is gaining in importance. The production of hybrid compounds by forging is a promising method to manufacture functional parts by applying resource-saving process steps. In compound forging a hybrid raw part consisting of a solid core, which is enclosed by a hollow casing, is joint in the forming process. This results in a graded material structure in the part in which the mechanical properties can be specifically adapted to the requirements. Compound forging is the form joining and/or firmly bonded joining of at least two different materials while plastic shape forming occurs (Figure 1)."

Jan 1, 2012