Search Documents

By Jamil M. Khalifeh, Shadia J. Ikhmayies, Bothina A. Hamad

"The structural and electronic properties of cubic d -NbN are investigated using density functional theory (DFT) and all-electron full potential linearized augmented plane wave method (FPLAPW). The equilibrium structural parameters are determined by fitting the total energy as a function of volume to the Murnaghan's equation of state. We calculated the total and partial densities of states (DOS) and compared them with those computed by different authors. Our DOS at Fermi level is found to be very close to the experimental value. The band structure is computed, discussed and used to find the characteristic energy separations. Valence electron density contours are recorded and discussed. We deduced the partial charge densities of different bands and binding energies of valence core levels and compared them with experimental and theoretical results obtained by different authors.IntroductionNiobium nitride has been intensively investigated over the last decades because of its interesting physical properties and technological applications (superconducting microdevices, microelectronic, catalytic probes, and hard coatings) [l]. While the group IV transition metal nitrides (TMN) mainly crystallize in the cubic NaCl structure (Bl type), those of group V and VI nitrides occur as different phases. Thus for niobium nitride, many phases have been reported in the literature: cubic fcc d -NbN, tetragonal ? -Nb4N3, hexagonal d -NbN, hexagonal e -NbN, and low nitrogen content hexagonal ß -Nb2N [l, 2].Structural and electronic properties of niobium nitride were investigated theoretically and experimentally by many authors. For example, in 1975 Schwarz [3] obtained the partial density of states for NbC and NbN from APW band structure calculations. In 1975 Kallne and Pessa [4] studied the electronic structure of Nb, NbC and NbN by using X-ray emission. In 2003 Amriou et al. [5] studied the electronic structure and bonding mechanism of NbC and NbN compounds using first principle total energy calculations using the full-potential linearized augmented plane wave method. Also in 2006 Sanjines et. al [l] studied the electronic structure of the hexagonal~Nb2N, hexagonal' d -NbN, and cubic d -NbN thin fihns by using X-ray photoemission spectroscopy. They [l] also calculated the densities of states for these phases and used them in the interpretation of the experimental valance band spectra. Most of these studies are old and there is a need for more recent studies. According to our knowledge, there are little comprehensive theoretical studies on this subject by using FP-LAPW method [5], which proved its ability to give accurate results. In this work we used the FP-LAPW method to study the structural and electronic properties of the cubic (fee) o-NbN (space group Fm-3m, prototype NaCl) crystal."

Jan 1, 2013

By Xinghua He, Shujing Zhu

"Cycled fluidized bed ash (CFBA), a significant portion of fly ash produced from coal-fired power plants and rejected from the ash classifying process, has remained unused due to its high free CaO and S03 content. It is necessary to extend research on the method to reduce the expansion and improve the compressive strength by some effective chemical activator. This paper presents experimental results on the expansion by Le chaterlier tester and the compressive strength. Hydraulic ash-zeolite (HAZ) cementitious material was blended as the chemical activator to study the effects of the activator on the expansion and the compressive strength. The results show that HAZ can not only reduce the expansion, but also increase the prisms compressive strength. Scanning electron microscope observation and X-ray diffraction analysis indicate that the main hydrated products of the sample are calcium hydroxide, ettringite, zeolite and calcite, which can explain the results of the expansion and the strength tests.IntroductionNearly 80% of the electricity in China is produced by coal-fired plants, which results in the production of a large quantity of coal combustion residues, among which coal fly ash is the major component. Because of that the air-pollution becomes heavier as time going on. Cycle-fluidized-bed-combustion systems are retrofitted to meet air-emission standards mandated by China Clean Air Act. Cycle fluidized bed ash (CFBA) will present new challenges for coal-combustion byproduct management. The use of cycle-fluidized-bed ash as a cement replacement in concrete is the most attractive one because of its high volume utilization and widespread construction. However, the replacement of cement with cycle fluidized bed ash in Portland cement concrete usually increases the expansion and decreases the early strength of concrete. In many research of this field, most of them were focus on the activation of pozzolanic activity of CFBA and to make all kinds of blend cement. A number of studies had been carried out on the activation of CFBA using chemical activators. These studies involved using different activating methods including alkali activation and sulfate activation 11, 2]. The former involved the breaking down of the glass phases in an elevated alkaline environment to accelerate the reaction [3, 4]. The later is based on the ability of sulfates to react with aluminum oxide in the glass phase of CFBA to produce ettringite that contributes to the strength at early ages [5-7]. With respect to sulfate activation, the use of gypsum and sodium sulfate had been well studied [5-8]. HAZ is one of HAS sub-products which is a patentd chemical activator made by Wuhan University (ZL98113594.3). It had been used to activate CFBA to produce blend cement in many Chinese engineering projects and time has told us that it is a good activator."

Jan 1, 2012

By M. Patel, G. Djambazov, J. Shrimpton

"Removing zinc by distillation can leave the lead bullion virtually free of zinc and also produces pure zinc crystals. Batch distillation is considered in a hemispherical kettle with water-cooled lid, under high vacuum (50 Pa or less). Sufficient zinc concentration at the evaporating surface is achieved by means of a mechanical stirrer.The numerical model is based on the multi-physics simulation package PHYSICA. The fluid flow module of the code is used to simulate the action of the stirring impeller and to determine the temperature and concentration fields throughout the liquid volume including the evaporating surface. The rate of zinc evaporation and condensation is then modelled using Langmuir's equations. Diffusion of the zinc vapour through the residual air in the vacuum gap is also taken into account.Computed results show that the mixing is sufficient and the rate-limiting step of the process is the surface evaporation driven by the difference of the equilibrium vapour pressure and the actual partial pressure of zinc vapour. However, at higher zinc concentrations, the heat transfer through the growing zinc crystal crust towards the cold steel lid may become the limiting factor because the crystallization front may reach the melting point.The computational model can be very useful in optimising the process within its safe limits.IntroductionLead bullion is commonly refined by removing various impurities (e.g. copper, silver, bismuth, antimony, etc) sequentially. This in normally achieved by the addition of reagents which selectively react with the impurities and the resulting compounds removed by various means. To aid efficient mixing (ensure uniform reactions), batch mixing of materials via the aid of impellers is common practice in a number of industrial sectors. Excess zinc, added during the desilvering process can be removed by one of three methods: (1) Vacuum dezincing - During vacuum dezincing, a vacuum is drawn on the agitated molten lead within a hemispherical vessel (Figure 1). Vaporized zinc condenses on the inner top surface of the vessel. The temperature at which zinc commences to vaporize lowers owing to heating under a vacuum. This enables vaporized zinc to be recovered in the form of high purity crystals without oxidation. The zinc crystals are recovered once the vessel lid is removed and the vacuum is broken. (2) Chlorine dezincing - In chlorine dezincing, molten desilvered lead is reacted with chlorine gas, forming a surface layer of zinc chloride contaminated with small amounts of lead chloride."

Jan 1, 2004

By I. Kim, J. C. Choi, W. D. Cho

"The effect of yttrium addition on the oxidation behavior of Fe3Al intermetallic compound was investigated in the range of temperature 800 to 1100 °C in 0.2 atm 02 in terms of oxidation rate and oxide adhesion. The oxidation rate of alloys, Fe-14.3 wt% Al and Fe-14.1 wt% Al-0.3 wt% Y, was nearly identical and the parabolic rate constant calculated as a function of temperature is Kp=5128 exp[-39506(cal/mol)/RT] mg2/cm4 hr.Rapid cooling and ultrasonic stress tests were carried out to test adhesion of scale formed on the alloys. While the oxide layer formed on the Fe-Al alloy without Y was found to be fragile and detached easily during the tests, the oxide layer formed on the Fe-Al alloy containing Y was protective, dense, and adhesive. The following two mechanisms were proposed to explain the adhesion improvement of Ah03 formed on the Fe3Al containing yttrium : (1) the addition of yttrium decrease generation of growth stress in alumina scale because the preferential diffusion of yttrium through grain boundary in alumina scale prevent internal oxidation of Al, one of main causes of growth stress, and (2) the second phase formed on the oxide scales prevents crack propagation through the scales, leading to better mechanical stability of the oxide scales.IntroductionIron aluminides have attracted the attention of many researchers as a candidate for use at high temperature because of their excellent oxidation resistance due to the formation of protective alumina scale. In order to resist aggressive environments at elevated temperatures, oxide scale formed on iron-uluminum alloy must satisfy the following three requirements : (1) thermodynamic stability (2) slow growth rate (3) adherence on substrate. According to Wallwork and Hed [l], the most suitable alloys for high temperature application are Fe, Ni, and Co alloys with the protection of Si02, Cr203, and Ah03 scales. While chromium oxide can vaporize as Cr03 above 1000 °C and silicon oxide may form low melting silicate [2,3], Alz03 has a high melting point and is the most stable among the three oxides thermodynamically [6]. In this respect, iron aluminides forming alumina seem to be most suitable for use at high temperature. However, alumina scale formed on the iron aluminum alloys tends to be easily spalled during oxidation due to the combination of growth stress and thermal stress."

Jan 1, 1998

By Jesse White, Arlin Olson

"An Engineering Scale Technology Demonstration (ESTD) unit utilizing the THOR fluidized bed steam reforming technology was built and operated by Hazen Research, Inc. for the purpose of denitrating and solidifying various Department of Energy (DOE) radioactive tank waste surrogates into granular products. The ESTD offered the opportunity to investigate the operational characteristics of two fluidized beds in series to test process system designs such as those for fluidization, feeding, and product collection. Operational characteristics that were evaluated included bed attrition rate, particle growth, and elutriation; and the effects that variations in process parameters (e.g., fluidizing gas flow rate, feed composition, feed injection method, and gas distributor design) had upon these characteristics were observed. Testing of the process systems on this scale allowed for design changes to be made where the cost in time and money were significantly less by comparison to those same modifications being made on the commercial scale.IntroductionFluidized bed steam reforming (FBSR) offers a moderate temperature (620-750°C) continuous method by which various liquid wastes can be processed irrespective of whether they contain organics, nitrates, sulfates/sulfides, chlorides, fluorides, volatile radionuclides or other aqueous components. The FBSR technology has exhibited the potential to process these wastes into either a carbonate or crystalline ceramic (mineral) granular product.Pilot scale testing was performed using the THOR Treatment Technologies, LLC (ITT) FBSR process, as it offered the opportunity to evaluate multiple aspects in an environment more conducive to experimentation. Process changes and system modifications could be made faster and with less cost impact as compared with changes to an assembled commercial plant. These aspects include verification of process chemistry and kinetics, evaluation of materials of construction, equipment sizing and design, and the interactions of the systems. Evaluation of process chemistry allowed for the verification of thermodynamic and kinetic models, and was used in conjunction with these models to improve the database and modeling assumptions. It also allowed for the reevaluation of data from earlier bench scale testing with the opportunity for long-term operations. These long-term effects may include the buildup of one or more elements that results in the formation of eutectics leading to the destabilization of a fluidized bed, or the shift in particle size as a result of attrition or agglomeration. The pilot plant also provided an environment to evaluate materials of construction."

Jan 1, 2014

By Mehdi Asgharifar, Rouzbeh Sarrafi, Radovan Kovacevic

"The surface treatment of aluminum alloys using atmospheric-pressure of low intensity DC plasma arc discharge is investigated in terms of surface properties. With respect to the conventional surface treatment processes for aluminum alloys mostly based on chemical etching or sand blasting, this process is very environmentally friendly and cost-effective. The effect of two processing parameters, the current and the plasma torch scanning speed, on the surface morphology is studied by using a scanning electron microscope. The effects of cathode spots within the tested range of process parameters are determined, and the limiting factors of the process (such as surface cracking) are discussed. The topographical studies of the treated surfaces have suggested potential enhancement of surface properties for different applications, such as preparing surface for painting and adhesive bonding.IntroductionIn the last decade the aluminum alloys are finding broad applications in automotive industry. In order to successfully execute the joining process of aluminum alloys such as arc welding, laser welding, and adhesive bonding, there is a need to remove oxides for welding and texture the surface for bonding along the join line. A number of surface treatment techniques such as chemical etching, sand blasting, and plasma treatment have been used by industry. It is shown [1] that plasma surface treatment is characterized as environmentally friendly, lower cost, and easier to control process. Bogaerts et al. [1] mention that when an adequately high potential difference is applied between cathode and anode, electrons are accelerated toward anode by an electric field coming in collision with gas atoms. The gas breaks down into positive ions and electrons, giving rise to gas discharge. The DC electrical discharges used in industrial plasma sources can be related to their location on the voltage-current curve as shown in Figure 1.It is generally believed that dark discharges other than coronas, and arc or torch plasmas are not very good candidates for surface treatment because oflow or high power density and active species flux. However, the glow discharge plasma is used for plasma surface treatment applications because of its proper power density and active-species flux [2]. Our objective is to investigate the feasibility of using low intensity DC plasma arc discharge as a surface treatment method without damaging the cathodic non-thermionic workpiece."

Jan 1, 2011

By Hubert Bril, Priscilla Pareuil, François Bordas, Emmanuel Joussein, Jean-Claude Bollinger

"According to the legislation, valorization type, origin and characteristics of waste material, various standard procedures are available to evaluate environmental impacts. A Mn-rich slag was sampled from a metallurgical plant. After its characterization (elementary analysis and mineralogy), five standard procedures were carried out (i.e. TCLP, EN 12457-1). Each fixed parameter of the standards was systematically studied in a large range: pH, Liquid/Solid ratio, contact time. For example, EN 12457-1 led to a low ME mobilization, increasing with the L/S ratio, the contact time and an acidic pH. As a conclusion, the representativeness of the considered parameters and their potential variations are predominant to assess of the real environmental impact during slag reuse. Introduction Recent studies have been carried out about environmental impacts of waste containing metallic elements (ME) because of their potential mobility [1-7]. Indeed, slags are either dumped or valorized in various activities such as building materials. In order to assess environmental risk, various standard procedures are used depending on country legislation, origin of waste and valorization way. Results of leaching tests are linked either to special legislation (e.g. Dumping: EC, Council Decision 2003/33/EC, Construction products: EC, Council Directive 89/106/EEC) or to legal levels used in drinking water (Directive 98/83/CE) when leachates could migrate to groundwater. If ME in leachates are lower than drinking water authorized levels, the waste will be considered as non-hazardous. On the contrary, if the leachable amounts exceed them, the question about the risk has to be posed. Beyond the abundance of leaching tests available, variety of operational conditions induced by these regulatory tests does not make the choice easier. According to operational conditions induced, ME release could vary from one test to another one. ME concentrations in leachates depend on pH, Liquid/Solid ratio, contact time and particle size [3]. To highlight the importance of these operational parameters, potential risk for valorization of a manganese-rich slag was assessed by comparing several standard leaching protocols [8-12] with a global study dealing with the influence of operational conditions. For each regulatory protocol, the most influential parameters (L/S ratio, pH, particle size and contact time) have been studied in a large range."

Jan 1, 2008

By Magdelinka Padenkova-Yaneva, Emilia Christova Kostakeva

"Environmental protection is becoming over the years an increasingly significant problem of mankind. Up to the last decade the only way to make the domestic waste harmless in Bulgaria was deposition on uncontrolled landfills without undertaking actions for protection of the soils. This also caused pollution to spread into the surface and underground waters and that is why actions are now undertaken for remediation of contaminated soils. This is achieved by developing projects for the closing down of polluted sites. In the present paper some projects for closing down of polluted areas are discussed. The actual conditions are examined and project decisions for preventing the surface waters from penetrating into the waste are presented. In this way the pollution of the soil is stopped and the soils are gradually remediate.IntroductionSoil is the topmost layer of the earth crust. It consists of mineral particles, organic substances, water, air and living organisms and is an extremely complex and changing living environment. Soil is a non-renewable natural resource which is of considerable importance in a number of crucial processes (production of foods, storing, filtrating and turnover of many substances, including water, carbon and nitrogen). It also serves as a basis for human activities, shaping the landscape, ground on which cultural heritage is built, and source of raw materials. These functions of soil must be protected both because of their social and economic significance and from the point of view of environmental protection.The processes of erosion, loss of organic substances, compaction, salination and contamination contribute to the degrading of soils accompanied by a negative impact on human health, natural ecosystems and changes in climate, as well as on the economy. All these make it necessary to protect soils from contamination. Over the last years intensive work started in Bulgaria for the construction of controlled sanitary landfills for rendering municipal solid waste harmless. Pursuant to Bulgarian legislation, in these controlled sanitary landfills measures are undertaken for protecting the soils from contamination through appropriate project decisions – the filtration of the products from the biological decomposition of waste into the adjacent sites (soils) and, therefore, the contamination of the surface and underground waters is prevented. At the same time the purity of air is maintained, human health is protected and conditions are created for including the controlled sanitary landfills into the surrounding landscape."

Jan 1, 2008

By Jean Igor Margem, Rômulo Loiola, Sergio N. Monteiro, Foluke S. de Assis, Frederico M. Margem

"Fibers extracted from the ramie plant have been traditionally used in textile and are now being considered as polymeric composite reinforcement owing to their superior strength. Recently the mechanical behavior of ramie fiber reinforced polyester composites was investigated but no significant improvement was found. Therefore, the objective of this work was to carry out a similar investigation by changing the type of polymeric matrix. Specimens with up to 30% in volume of ramie fibers incorporated into epoxy were bend-tested until fracture. The results showed a moderate improvement with a tendency of decreasing stress for higher amounts of ramie fibers due to the weak interface developed with the epoxy matrix.IntroductionThe engineering application of natural fibers extracted from cellulose-containing vegetables, also recognized as lignocellulosic fibers, is presently considered an environmentally correct alternative to replace more expensive, non recyclable and energy-intensive synthetic fibers [1-3]. In fact, composites reinforced with traditional fibers such as coconut, sisal, jute, hemp, etc ... are already on the market in substitution for common glass fiber automobile components [4-6]. Even less known fibers like curaua from the Amazon region are being industrially used [7]. Economical and environmental reasons sustain a promising future trend for natural fiber composites. In comparison with the less expensive glass fiber among energy-intensive synthetics, lignocellulosic fibers are approximately five times cheaper. For the current situation of our planet, natural fibers are regarded as ""green"" environmentally friendly materials. They are abundant, renewable, biodegradable, and recyclable, above all, neutral with respect to carbon dioxide emission, associated with global warming.Several relatively unknown lignocellulosic fibers such as piassava [8], sponge gourd [9], sugar cane bagasse [10], buriti [11] and ramie [12], with simple and limited applications, or just byproducts, are now being investigated for their potential as composite reinforcement. This could widen the offer of new lignocellulosic fibers for composite reinforcement. The banana fiber, in particular, has a tensile strength around 700 MPa [13], which is comparable to the strongest lignocellulosic fibers used as composite reinforcement.In addition to polyester, the epoxy is another relatively strong polymer used as composite matrix. Therefore, the objective of the present work was to assess the mechanical properties obtained by flexural test, for epoxy composites reinforced with different amounts of banana fibers."

Jan 1, 2013

By Tzu-Chien Lin, Jack Tsai, Ming-Yu Lin, Der-Ray Huang, Jiin-Sen Chen, Jing-Xuan Lin

"In this paper, some DVD-R discs have been selected for long time light exposure test and high temperature and humidity test. Generally, recordable media under long time light exposure maybe be defected seriously. If we use Jitter value 8% as a reference to determine the life time of DVD-R samples, some discs defect after 5 hours of light exposure while some discs can endure over 25 hours. Also if we use reflectivity 45% to determine the life time, some discs defect after 30 hours light exposure while some discs can endure over 40 hours. From our results, the good samples show good characteristics of PI error. The absorption spectrum of recordable media is a good reference to justify the quality of dye media. These results can be used to estimate the life time of recordable discs.IntroductionIn general, the life time of DVD-R with a layer of organic dye recording layer is required for preservation in decades. In addition to optical characteristics and thermal properties, we still need to consider the stability of the dye in recording media. The presentation of the color on organic dye is not only related to the material's property but also related to the light exposure. In this study, we focus on the absorption characteristics and reflectivity of organic dye in optical recording layer after light exposure. The optical properties of discs depend on the functional groups and molecular structure [1]. According to ""DVD Specifications for Recordable Disc (DVD- R)"", the reflectivity should higher than 40%. From measured reflectivity, we can confirm that the important issue is whether dye be affected by light exposure or not. Because each specific functional group absorbs the specific spectrum, we can check the characteristics of functional groups from their UV/Visible Spectra. We also use High-performance liquid chromatography (HPLC) to detect the different components of dye on the recording layer [2]. The jitter value test is to test the error cause by digital signal of recording media. If we use jitter value 8% as a reference to determine the life time of DVD-R samples, the purpose of this study is to investigate the jitter values of recording media after high light exposure and high temperature/humidity test. The results of these test will be helpful for the development of long-life optical storage media."

Jan 1, 2012

By Linli Wu, Guangchun Yao

"The influence of deformation on the properties of short-carbon-fiber reinforced 2024 alloy matrix composites was investigated in this study. It was found that the distribution of carbon fibers changed from the random state before deformation to the ordered state that carbon fibers arranged along the direction of rolling and extruding after deformation. Under the temperature range in control, the increase of rolling and extruding temperature would benefit to improve strength and elongation of composites, but was not conductive to improve the hardness of composites. With the increment of total deformation, all the strength and the hardness of composites became greater, nevertheless the elongation decreased. After being rolled and extruded, the strength and the hardness of composites were all bigger than those of composites before being rolled and extruded; moreover, the strength of extruded 2024 alloy matrix composites was higher than that of rolled 2024 alloy matrix composites under the same heat treatment conditions.IntroductionCarbon fibers have been reckoned as very important reinforcements due to the high specific strength, specific modulus, high thermal and electric conductivity, low expansion coefficient and good self-lubricant properties [1-4]. Light metal composites reinforced with carbon fibers, such as carbon fibers in an aluminum matrix, are widely used and studied. Some studies have concentrated on the interfacial characteristic of CF/Al composites in order to search for the way of improving the bonding between carbon fibers and the matrix alloy [5-8], and on the influence of the carbon fiber percent composition in the composites [9-11]. Some researchers began to take interest in the deforming characteristic and failure behavior of carbon fiber reinforced metal matrix composites [12-16]. However, the same with other metal materials, most of CF/AI composites were prepared by some single processes, such as powder metallurgy, extrusion casting and vacuum press infiltration, which caused that the composites products could not be manufactured directly. In order to cover the shortage of the mentioned above processes and get composites products with perfect mechanical properties and dimensional accuracy, the composites should be reworked by rolling, extruding or forging process. Compared with research about manufacturing process, the correlative investigation on the reworking of CF/Al composites was much less evidently, which restricted the application and the further development of CF/Al composites."

Jan 1, 2012

By Jamil M. Khalifeh, Shadia J. Ikhmayies, Bothina A. Hamad

"We computed the optical properties of the cubic niobium nitride (o-NbN) compound using the full potential linearized augmented plane wave (FL-LAPW) method within density functional theory (DFT). The complex dielectric function and optical constants, such as optical absorption coefficient, refractive index, extinction coefficient, energy-loss spectrum, and reflectivity, are all calculated and compared with experimental results. The behavior of the computed quantities is similar to that obtained experimentally, but the optical positions are shifted to lower energies. This shift was related to the strong interband transitions, which are located at energies higher than 5 eV for NbN- as they are for IV B transition-metal mononitrides- and they appear in the computed spectra and not in the experimental spectra. These interband transitions simply shift the position of the reflectivity edge or the screened plasma frequency to the longer wavelength side.IntroductionIn recent years, NbN, as a transition metal nitride, has become a very popular material due to its high hardness, melting point, wear resistance, chemical inertness and temperature stability, which makes it suitable for use as emission cathodes in microelectronics and sensors, optical films and micro-mechanics etc [l]. Niobium nitride has long been known as highly polymorphic material, for which several crystalline structures have been reported in the literature [2]. These structures include the well known super-conducting rock-salt (Fm-3m, or Bl) structure (o-NbN), the hexagonal structure with space group p63/mmc and prototype Fe2N (18fuN), the hexagonalstructure with space group p63/mmc and prototype NiAs ~-NbN) and others.There has been a lot of computational studies for the structural and electronic properties ofNbN [3, 4-7], but according to our knowledge there is not any computational work that has been devoted to study the optical properties of this transition metal compound. At the same time a number of authors had performed experimental work in this direction. For example, Xin-kang et. al [l] studied the microstructure and optical properties of magnetron sputtered NbN thin films. Torche et. al [8] studied the composition, structure, electrical and optical properties of nonstoichiometric niobium nitrides. Newport et. al [9] investigated the reflection and transmission spectra of cubic niobium nitride films, and Tanabe et. al [10] had investigated the optical parameters and reflectivity of reactively sputtered NbN thin films by using in situ ellipsometry."

Jan 1, 2013

By A. V. Tarasov

In order to improve technical, economic and environmental performance of hydrometallurgical processing of intermediate products containing copper and nickel, the Gintsvetmet Institute and the IMET Institute of the Russian Academy of Sciences have conducted studies into the efficiency of the use of alternating current of industrial frequency on processes applied for hydrochemical leaching of various copper- and nickel-containing materials. It has been found that: 1.Imposition of alternating current over the process of leaching of softly reduced nickel oxide with recycled copper sulfate solutions resulted in an increase by 20 to 30% of the rate of the copper cementation process and reduced by 20% its activation energy. At the same time, the recoveries of nickel, cobalt and iron to the leach solution increased up to 82.2%, 78.5% and 57.1%, respectively, and that of copper to the cement precipitate up to 74%. Optimal process conditions have been identified with respect to the current density, electrode material, copper concentration in solutions and the process temperature. 2.In the process of hydroelectrochemical sulfuric acid leaching of nickel and copper sulfides, the grain size, the phase form of sulfides, the solution composition (H2SO4, Cl?, Cu2+, Fe3+)and the current amperage had an effect on the nickel recovery to the solution, which reached 90%, while the degree of copper transfer to solution did not exceed 20%. The process of hydroelectrochemical sulfuric acid leaching of nickel and copper sulfides with an addition of Cl? made it possible to selectively recover nickel into the leach solution along with concentrating copper in the leach residue. 3.When subjecting samples of commercial-grade magnetic fractions of converter matte to sulfuric acid leaching, the imposition of electric current, the concentrations of sulfuric acid and chloride ion in the solution and the duration of the reaction process had an effect on the process. The nickel recovery was 85% and that of cobalt and iron was 95% and the recoveries reached 97.5%, 98.3% and 99.8% as a result of repeated treatment of the primary residue under similar process conditions. Up to 75% of copper, 75% of sulfur and 99.0-99.5% of palladium was concentrated in the solid reach residues. The experimental data obtained indicates that the use of AC for hydroelectrochemical sulfuric acid leaching for separation of copper- and nickel-containing intermediate products has favorable prospects.

Jan 1, 2003

By David J. Howard, Christine Broadbridge, David C. Paine

"High pressure vapor/solid reactions offer an opportunity for novel synthesis and processing of thin film materials and structures for electronic, optical, and magnetic applications. In this paper we review the use of two high pressure techniques that operate from 25 to 1000 atm (2.5 to 100 MPa) to fabricate thin film oxide structures from Si1-xGex deposited on Si wafers. High pressure synthesis enables temperature-independent control of reaction rates in the oxidation of this multicomponent semiconductor system and hence offers the opportunity to form thennodynamically metastable Si1-xGex<h from the alloy. The thermodynamics of the Si-Ge-0 system are reviewed and a method is described that utilizes selective chemical reduction (via H2 gas) of Si1-xGcx<h to form Ge precipitates in an SiO2 matrix. IntroductionAlloys of Si1-xGex grown epitaxially on Si substrates by chemical vapor deposition (CYD) and molecular beam epitaxy (MBE) have been used to create high performance microelectronic devices1. These devices show improved performance over conventional Si technology because they exploit the Si/Si 1-xGex band-gap discontinuity and take advantage of higher hole mobilities in the Ge containing alloys. While a range of devices based on heteroepitaxial systems have been demonstrated, the Si1_xGex alloys are of particular interest because they are most closely compatable with standard Si device processing. One disadvantage of Si-based materials systems is that they are not typically useful emitters of light. This is important since the use of light (rather than electrons) for transmitting and processing signals into, out of, and within Si-based microelectronics would represent a major technological advance in microelectronics-based communication and computer technologies. Nevertheless, through the use of innovative processing techniques it may be possible to use the Si1_xGex/Si heteroepitaxial system in integrated microelectronic/light-wave technologies."

Jan 1, 1994

By Christian Redl

"The Lattice Boltzmann Method (LBM) solves fluid dynamics problems based on a discrete mesoscopic approach. It is based on the Lattice Boltzmann equation which is a special discretisation of the continuous Boltzmann equation. Its principle advantage is that it can handle complex physical phenomena (like interaction between different components and surface effects), complicated boundary and initial conditions very well, free from many gridding and stability constraints that plague conventional numerical methods used for fluid flow simulations. Complex structures like porous media can be resolved directly. The LBM algorithm has a simple structure and acts locally, which is favourable for parallel computing. Its potential for metallurgical process simulation is demonstrated in the present study which is concerned with the simulation of the fluid flow in a copper winning electrolysis cell. The electrolyte is modelled as the carrier fluid and the oxygen is considered via a so called active scalar equation. The modelling of buoancy, momentum exchange and the free surface requires special effort. The results of the simulation are validated against experimental data obtained by Laser-Doppler-Anemometry. Despite the simplifications made, good agreement between the simulation and the experiments was found.IntroductionThe hydrodynamics in an electrometallurgical cell is a complex, highly non-linear phenomenon. It includes the simulation of a two component system with high density ratio, gravity driven flow and a free surface. A general solution to this problem is currently unknown.The flow field is a result of the combination of various hydrodynamic effects [18]. Metal deposition at the cathode yields in a decrease in the ion concentration, which reduces the density of the electrolyte. At the anode molecular oxygen is formed as a consequence of the oxidation of water molecules. The oxygen is solved in the electrolyte and again the electrolyte density is decreased. Both effects lead to a free upwards directed convective flow, refered to as natural convection."

Jan 1, 2001

By Bruce W. Wessels

"Metal-organic chemical vapor deposition has been shown to be a highly versatile technique for the synthesis of complex oxides. High dielectric constant oxide thin films of SrTiO3, BaTiO3, Ba1-xSrxTiO3 and SrxBa1-xNb2O6 can be be be deposited at 800 ºC with this technique. The fluorine substituted B-diketonate precursors have been shown to be well-suited for the deposition of high quality, epitaxial thin films of these materials.IntroductionThere has been a resurgence of interest in thin film ferroelectric oxides as a result of the development of techniques to deposit high quality material. Both physical and chemical vapor deposition techniques have been realized. Of the chemical vapor deposition techniques, metal-organic chemical vapor deposition (MOCVD) has received the most interest for the deposition of ferroelectric oxide thin films. This results, in part, from the availability of a number of volatile metal-organic precursors.(l) Moreover, MOCVD offers the advantages of high growth rates, uniform coverage over large areas, conformability, abrupt interfaces and excellent epitaxial crystallinity. Of the metalorganic precursors, the B-diketonate complexes have played an important role especially in the deposition of ferroelectric oxides containing alkaline-earth metals such as BaTi03 and Ba1•XSrxTi03. For example, barium tetramethylheptanedionate Ba(thd)2 has been used in the preparation of BaTi03 by MOCVD.(2) These compounds, however, are not without their problems. Ba(dpm)2 has a relatively low volatility; and as a consequence, temperatures in excess of 180·C are required for volatilization. This leads to the necessity of a complex precursor delivery system to insure that the precursor does not condense before the reaction zone. Moreover, the Ba precursor tends to oligomerize leading to a decrease in vapor pressure as well as a problem with reproducibility. To counter these problems, novel liquid source and solid source precursor delivery systems have been developed. (3)(4)"

Jan 1, 1994

By Wander. L. Vasconcelos, Virgínia. S. T. Ciminelli, Angela. M. F. Guimarães

"The present work was aimed at synthesizing nanostructured hybrid materials derived from the functionalization of smectite clays with ligands containing thiol (-SH) groups for application in cadmium adsorption processes. An in nature Brazilian bentonite was investigated. The modification route was based on the grafting reaction between hydroxyl groups present on clay surface and the hydrolyzable alkoxy group of the (3-mercaptopropyl)trimethoxysilane in dry toluene under reflux. The present work showed that the proposed modification route was effective for the grafting of the thiol groups in the clay structure. The thiol-functionalized bentonite samples showed average binding capacities 160% higher with respect to Cd2+ to those obtained with the ungrafted material. These results support a mechanism of adsorption involving primarily ion complexation by the thiol groups (specific) instead of cation exchange (unspecific). The proposed modification processes are suggested for the preparation of novel adsorbent materials with controlled selectivity and specificity and therefore with good potential for separation and pre-concentration purposes.IntroductionMany efforts have recently been devoted to the design and preparation of inorganic-organic nanomaterials because of their potential application in novel functional materials. The intercalation of organic species within the spaces between interlayers of inorganic layered crystals provides nanostructures consisting of alternating layers of inorganic and organic compound. The intercalation reactions occur by insertion of mobile guest species (neutral, molecules, or ions) into the accessible crystallographic-defined vacant sites located between the layers (interlayer spacing) of the layered host structure [1}.Silane coupling agents, used widely for the modification of silica surfaces, have also been employed more recently for modification of layered silicates [2,3,4,5]. Modification with organosilane involves grafting reactions by establishing covalent bonds between the reactive groups of the layer, normally hydroxyl groups, and silane molecules. These reactions can be restricted to the external surface (the basal spacing remains unchanged) or to the interlayer surface, in which case an interlayer expansion occurs. The resulting material can be defined as a hybrid material or, more specifically, functionalized inorganic layered material [1]."

Jan 1, 2008

By Caisa Samuelsson, Sina Mostaghel, Theo Lehner

"Rönnskär smelter of Boliden Mineral AB, Sweden, is well known for recycling of base and precious metals. Slag from the electrical furnace is processed at the fuming plant to produce zinc clinker. The granulated slag is a by-product used as e.g. construction material. In this paper, influences of Al2O3 on mineralogy of the slag, which can affect its chemical and physical properties, are investigated. Different mixtures of Al2O3/fumed slag were prepared. Re-melting was carried out in a Thermo-Gravimetry (TG) furnace with an inert atmosphere. Scanning electron microscopy (SEM) and X-ray diffractometer (XRD) were then applied for the analyses. Investigations depict that addition of alumina to slag, results in an increase in the number of spinels and a transformation from iron rich to aluminum rich spinels. Anorthite (CaAl2Si2O8) will also be formed.IntroductionRönnskär smelter of Boliden Mineral AB is located in north of Sweden; the main products of this smelter are: Copper, Zinc clinker, Lead, Gold, and Silver, while sulphuric acid, liquid sulphuric dioxide, and Iron sand are some of the by-products. Reducing the energy consumption and decreasing the usage of finite natural resources are becoming more and more important for the Rönnskär smelter; this result in use of different recycling and scrap materials. Metal residues, from brass foundries, steel mills, and electronic scrap are recycled at Rönnskär smelter [1]. Most of the electronic scraps contain mixtures of various metals together with plastics and ceramics, which can affect the composition and properties of the slag considerably [2]. At the same time, treatment of slag and controlling its composition and properties are of much interest for Base Metals producers from different aspects. Composition of slag influences the physical properties such as: 1) Liquidus temperature [3-4] 2) Viscosity, which controls separation of valuable metals, especially copper by gravity separation [2] and also heat and mass transfer [5] 3) Electrical conductivity [6]."

Jan 1, 2008

By Mala Nath, Atjit Mallick, Asheesh Kumar

"The present research work is aimed to focus on the development of chemically stable light weight microporous carbonaceous material, such as activated charcoal incorporated either with titanium n-butoxide, titanium diisopropoxide bis(2,4-pentanedionate), vanadium 2,4-pentane-dionate or zinc 2,4-pentanedionate having varying wt% of the metal (2-8%) using ethanol as solvent at 40--50 oC followed by calcinations at 100, 150 and 200 cC, except the samples with titanium diisopropoxide bis(2,4-pentanedionate) which are calcinated at 80 oC. Atomic absorption studies along with FESEM revealed that the maximum incorporation of metals (Zn, V and Ti) in activated charcoal was observed with 4 wt% of zinc 2,4-pentanedionate calcinated at 150 oC , 4 wt% of vanadium 2,4-pentanedionate at 100 oC, 2 wt% of titanium n-butoxide at 100 oC and 2 wt% of titanium diisopropoxide bis(2,4-pentanedionate) at 80 oC, and equilibration time of 20-24 h was used in each case. Hydrogen sorption behavior in these carbonaceous materials has also been studied at 77.4 K and low pressure up to I bar. The highest hydrogen uptake obtained was 1.45 wt% (164.5 cm3 (STP)/g at P/Po = 1.0) for activated charcoal incorporated with 4 wt% of zinc 2,4-pentanedionate calcinated at 150 oC.IntroductionTwo of the major challenges for humanity in the next twenty years are the shrinking availability of fossil fuels, the global warming and potential climate changes that result from their ever-increasing use. So it is necessary to fmd an energy source that is convenient, flexible and controllable. One possible solution to these problems is to use an energy carrier such as hydrogen, and ways to produce and store hydrogen in electric power plants and vehicles. Hydrogen storage is the bottleneck for the breakthrough of hydrogen as energy carrier in automotive applications [1]."

Jan 1, 2012

By Xinli Wang, Matthew Andriese, Jiann-Yang Hwang, Zhiwei Peng, Byoung-Gon Kim

"The microwave dielectric properties of silicon dioxide at frequencies of 915 and 2450 MHz were characterized in the temperature range of 24 to approximately 1000 °C using the cavity perturbation technique. It is shown that the relative dielectric constant of silicon dioxide at both frequencies remains almost unchanged below 500 °C, above which there is a slight increase of 2%. The relative dielectric loss factor of silicon dioxide exhibits a strong temperature dependence above 500 °C and increases by approximately 7 and 5 times at 915 and 2450 MHz, respectively. The substantial increase in the relative dielectric loss factor is mainly attributed to the enhanced dielectric polarization and accelerated electrical transport in silicon dioxide at elevated temperatures.IntroductionSilicon dioxide (Si02) is usually considered a microwave transparent material due to its poor absorption capability at room temperature [1]. This characteristic has led to various applications of silicon dioxide in microwave processing of materials and communication. For instance, Si02 has been used to produce sample holders for microwave heating and substrates for electronic devices [2,3]. These applications generally require the material to withstand high temperatures under microwave irradiation. This indicates that microwave absorption capabilities of silicon dioxide at elevated temperatures are also important for its utilization.The microwave absorption capability of Si02 can be determined based on dielectric characterization (permittivity measurement) of the material at commonly used microwave frequencies, 915 and 2450 MHz, in a broad temperature range. To date, however, no detailed work on the dielectric properties (permittivity) of silicon dioxide at high temperatures has been reported. The present work is aimed to study the dielectric properties of silicon dioxide from room temperature to approximately 1000 °C at 915 and 2450 MHz. The results show that the permittivity of silicon dioxide has a strong temperature dependence above 500 °C, suggesting a substantial increase in its microwave absorption capability."

Jan 1, 2013