Search Documents

By Qin Li

An highly active absorbent with oxidization based on fly ash, lime and additives was prepared. Experiments of simultaneous desulphurization and denitrification were carried out using fixture bed and duct injection. The influential factors for the absorptive capacity of the absorbent were studied. The absorptive capacities of 120.7mg for SO2 and 43.7 mg for NOx were achieved at a Ca/(S + N) molar ratio 1.2, respectively, corresponding removal efficiencies of 87% and 76%, while spent absorbent appeared in the form of dry powder. The optimal temperature and humidity of flue gas treated with this process were shown to be approximately 50\\176 and 5% respectively. The mechanism of removal for SO2 and NOx was investigated. In comparison with traditional dry FGD, this process appears to have lower cost, less complicated configuration and simpler disposal of used absorbent. The valuable references can be provided for industrial application by this process. The foreground of application will be vast in China and in the world.

Jan 1, 2006

By P. M. Rosário

The extraction performances exhibited by a phosphoric (D2EHPA), a phosphonic (Ionquest 801), a phosphinic (Cyanex 272) and a dithiophosphinic (Cyanex 301) acid derivative towards indium recovery from a diluted sulfuric solution are evaluated and compared. Equilibrium extraction isotherms were obtained. The chemical reactions involved and the approximate stoichiometry of the In(III) extracted species by the four ligands are presented and discussed. Stripping of In(III) from loaded D2EHPA and Ionquest 801 has been accomplished successfully, but has not been so effective from loaded Cyanex 301. Plots of %E vs. pH were established for D2EHPA, Ionquest 801 and Cyanex 301, denoting their behavior towards the extraction of similar mass concentrations of In(III), Fe(III), Fe(II) and Zn(II). Cyanex 301 is the least selective towards In(III), whereas D2EHPA and Ionquest 801, both for a pH = 0.5, do not extract Zn(II) at all.

Jan 1, 2003

By V. I. Lakshmanan

Whilst the prices of metals in nominal terms have largely remained static over the past forty years, in real terms, the primary metals industry receives very much less today for its products than in the past. Yet, it has largely managed to remain competitive, despite the fact that ore reserves are not only diminishing, but are of lower grade and higher complexity, and that there are much greater pressures on companies to be good environmental stewards. This paper examines how hydrometallurgical processing has shown itself to be highly innovative in order to remain viable both economically and environmentally. Aspects of process chemistry are discussed, and the lessons to be learned from having a good understanding of this chemistry are highlighted with reference to a number of case histories such as HPAL for nickel laterites, the Avmin/Chambishi Cosac Project, use of chloride chemistry for titanium extraction, and plant effluent treatment and recycle.

Jan 1, 2003

By Hirokazu Narita

The extractability for Pd(II) using MOTDA and DHS and their durability against a mixed solution of HNO3 and HCl was investigated by solvent extraction and FT-IR measurements. Both MOTDA and DHS selectively extracted Pd(II) over Pt(IV) from 0.75 M HNO32.25 M HCl solutions. The extraction rate of Pd(II) with MOTDA was much greater than that with DHS. In the durability test, the extraction percentage of Pd(II) and the FT-IR spectra were measured using MOTDA and DHS after stirring with 0.75 M HNO32.25 M HCl solutions. The extraction percentage of Pd(II) with MOTDA hardly changed during the two-month stirring; however, that with DHS decreased with an increase in the stirring time. The FT-IR spectra showed the sulfoxide formation by the oxidation of the sulfide in DHS, but not in MOTDA. Consequently, it was found that MOTDA is more durable than DHS.

Jan 1, 2006

A full-scale test of chalcocite heap bioleaching was undertaken at Straits? Nifty Copper Operation. Straits worked closely with the CSIRO to investigate the chemical and biological changes over the life cycle of this chalcocite heap bioleach system. Results indicated nearly 80% copper recovery was achieved in just over 300 days. Significant changes in iron chemistry and microbiological activity were detected. Temperatures in the heap reached as high as 70 ºC during the time of maximal copper recovery rate. The dominant cultivatable bacterial strains were typical mesophilic bacteria, however, naturally occurring moderately thermophilic bacteria were detected by culture and culture independent molecular (PCR followed by denaturing gradient electrophoresis [DGGE]) and signature lipid methods. Signatures for the iron and sulfur-oxidising species Acidithiobacillus ferrooxidans and Sulfobacillus spp., as well as the moderately thermophilic heterotroph Alicyclobacillus sp. were detected. Biomass was greatest in ?warm? but not ?hot? parts of the heap, and Hyperthermophilic Archaea were not detected.

Jan 1, 2003

By H. Y. Cho

LS-Nikko Copper Inc, has been operating its Onsan copper smelter since 1979. The smelter began its operation with a designed capacity of 80,000 tpa of copper from concentrates and its smelting capacity was increased to 140,000 tpa of copper by modifying the existing line in 1988. The Mitsubishi Continuous Smelting and Converting Process has been operating since 1998 at the initial capacity of 160,000 tpa of copper. In 2002, the smelting capacity of the Onsan smelter has been increased to 426,000 tpa of copper from concentrate. Now the Onsan smelter has plans to increase its smelting capacity to 500,000 tpa of copper from concentrates by 2010. During the expansion work, the modernization of facilities will be accompanied by an increase in smelting capacity, via the Outokumpu process. This paper reviews the brief history of smelting capacity increase in Onsan smelter and its Outokumpu process modernization plans.

Jan 1, 2006

Iron(II), sulphur dioxide and sugars such as lactose are potential reducing agents for manganese dioxide to produce manganese(II) for subsequent hydrometallurgical treatment. The leaching of limonitic laterite and manganiferrous ores with sulphur dioxide produces iron(II) which in turn can catalyse the leaching of manganese dioxide in acid media. This paper presents a critical analysis of the kinetics of reductive dissolution of synthetic manganese dioxide and manganese ore to compare and contrast the effect of sulphur dioxide and iron(II) in acid media containing sulphate or perchlorate anions. Both one-electron and two-electron mechanisms are considered in the case of sulphur dioxide. The current knowledge on chemical speciation is used to construct an Eh-pH diagram to show the effect of complexation of Mn(II), Fe(II) and Fe(III) with sulphate. Heterogeneous and electrochemical reaction kinetic models are combined to propose reaction mechanisms which rationalize the dissolution kinetics.

Jan 1, 2003

By Nobuaki Sato

For decontamination of SO2 containing waste gases from industries such as ferrous and non-ferrous metal companies, desulfurization with hydrogen production by the reaction of Br2 and SO2 was proposed as bromine-sulfur (BS) process. In this process, SO2 is fixed as H2SO4 in the presence of Br2 and H2O forming H2SO4 and HBr. Then hydrogen is produced by the decomposition of HBr and Br2 as byproduct is recycled. The reaction of Br2, SO2 and H2O was found not to occur in liquid phase but to occur in vapor one. The production ratios of H2SO4 and HBr showed a maximum at temperatures around 60 oC. The highest production ratio was obtained at 70 oC with a mixing ratio of Br2:SO2:H2O=1:1:10. The experimental results were discussed with thermodynamic consideration.

Jan 1, 2006

By O. M. G. Newman

Research into potential applications of spouted bed electrowinning (SBE) in the zinc industry was conducted, in a collaboration between our two organizations. The main system investigated was zinc from acidic sulfate electrolytes. However, SBE can be extended to other electrolytes, or recovery of other elements. Electrolytic tests were carried out at the 0.01 to 0.1 m2 scale. Spouting behaviour has been studied at a larger scale, approaching a size suitable for an industrial unit cell. Much of our work was carried out using a micro-porous separator (Daramic®). However, we have also shown that ion exchange properties can have a controlling effect on the process chemistry, electrochemical efficiency, and plant flowsheet. In initial 0.1 m2 scale electrolytic tests, design and engineering issues for scale-up were identified. We review the major achievements, promising areas for application in the zinc industry, current status, and remaining barriers to development of SBE technology.

Jan 1, 2003

By Hiroyuki Matsuura

Treatment of electric arc furnace (EAF) dusts has become an important issue from the viewpoint of the environmental protection and recycling of variable resources because these dusts contain considerable amount of zinc and lead. A new recovery process of these metals has been proposed, in which the metals in the dusts react with waste polyvinyl chloride to form metal chlorides. Therefore, it is important to clarify the physicochemical properties and behaviors of zinc, lead and those chlorides and oxychlorides. In the present study, the kinetics of chlorination of ZnO, PbO and ZnFe2O4 mainly contained in the EAF dusts were investigated at 1023 K to 1273 K with Ar-O2-Cl2 gas. Based on these results, the selective chlorination and evaporation process of zinc and lead from the mixture of Fe2O3-ZnFe2O4-ZnO-PbO was examined and the high efficiency of selectivity has been demonstrated.

Jan 1, 2006

By J. de Visser, J. A. Davis

Since the mid 1970's, development of zinc electrowinning (EW) facilities has out-paced its counterparts in the copper and nickel electrowinning industries in the design of efficient, compact, and automated production plants. Recent advances in process automation have provided opportunities to increase current efficiency, productivity and cathode quality, while reducing the footprint of the plant and the number of operating personnel working on top of the cells. Usually, the practice has been to allow a totally contaminated building structure, combining the plant ventilation system with the process cooling air. As a result, facilities employing this practice are finding difficult to meet their process design criteria and the stringent labor and environmental requirements. This paper provides an overview of the problems and disadvantages associated with these older process designs. It also describes new developments in ventilation systems, particularly building design developments and cost savings that are possible when improved ventilation systems are introduced into efficient process operations. Lead-

Jan 1, 2000

By C. R. Bennett

The first phase in the design, development and implementation of a comprehensive computational model of a copper stockpile leach process is presented. The model accounts for transport phenomena through the stockpile, reaction kinetics for the important mineral species, oxygen and bacterial effects on the leach reactions, plus heat, energy and acid balances for the overall leach process. The paper describes the formulation of the leach process model and its implementation in PHYSICA+, a computational fluid dynamic (CFD) software environment. The model draws on a number of phenomena to represent the competing physical and chemical features active in the process model. The phenomena are essentially represented by a three-phase (solid-liquid-gas) multi-component transport system; novel algorithms and procedures are required to solve the model equations, including a methodology for dealing with multiple chemical species with different reaction rates in ore represented by multiple particle size fractions. Some initial validation results and application simulations are shown to illustrate the potential of the model.

Jan 1, 2003

By Sundarrajm Suresh, Hrushikesh G. Pimpalgaonkar, Thiyagarajan Paramadayalan

In this paper, a model of a fuel cell system has been proposed to account for the membrane physics at the micro level which is coupled with the macroscopic flow and mass transport phenomena occurring in a single channel of a Polymer Electrode Membrane Fuel Cell (PEMFC) system. We have developed a novel approach to model the catalyst layer electrochemical processes in a Membrane Electrode Assembly (MEA) and coupled it with mass transport and fluid flow calculations at the channel level using STAR-CD commercial software. The predicted values of the cell voltage from this micro-macro model are validated with experimental data available in the literature. A sensitivity analysis has been carried out to study the effect of the design and operating parameters such as catalyst loading and initial temperature on the overall performance of the PEMFC. The results indicate that the cell voltage increases at higher platinum catalyst loading and is also independent of the choice of initial cell temperature.

Jan 1, 2012

By Toshihide Takenaka

Improvement of corrosion resistance of Mg metal by addition of rare earth metal (RE) was studied, and the effect of surface oxide layer with RE was investigated. The corrosion resistance of Mg was remarkably improved by adding a small amount of RE, and the suitable RE content was clarified. The corrosion resistance of Mg was particularly bettered by conversion coating using a solution including both RE(NO3)3 and Mg(NO3)2. This result indicates that the surface oxide layer consisting of both Mg and RE gives good corrosion resistance to Mg metal. In this study, direct electrodeposition of Mg metal containing RE was also tried in molten chloride with RE chloride, and it was shown that electrolysis could be performed stably. The RE content in the deposited Mg metal was depended on the concentration of RE chloride in the bath and the cathode potential, and Mg metal containing the suitable RE content for its corrosion protection was obtained easily by direct electrolysis.

Jan 1, 2006

By James Wang

In July 2003, The Office of Hydrogen, Fuel Cells and Infrastructure Technologies of the Department of Energy (DOE) Office of Energy Efficiency and Renewable Energy solicited Grand Challenge Proposals to establish three Centers of Excellence in hydrogen storage developments for reversible metal hydrides, non-reversible chemical hydrides and carbon storage materials, respectively. The program mission is to research and develop cost-effective, on-board hydrogen storage systems that enable a minimum range of 300 miles within the weight and volume constraints of the vehicle. Currently, no hydrogen storage technology available can meet the DOE cost and performance targets. In April 2004, Sandia National Laboratories was selected by DOE to lead the Metal Hydride Center of Excellence with partners from 5 other national laboratories. We will present the organization and recent accomplishments of the Metal Hydride Center which is confident to accomplish DOE/FreedomCAR and Fuels Partnership objectives for 2010 in hydrogen storage for vehicular transportation applications.

Jan 1, 2006

By Harold R. Kokal

Lisakovsky is a 3-billion ton oolitic iron ore deposit in north-central Kazakhstan operated by Orken LLP, a subsidiary of Ispat Karmet and the LNM Group. The iron oxide minerals are goethite and limonite. The gangue occurs as discrete quartz grains and an unidentified form of colloidal silica-alumina. The concentrate produced contains about 49.5 percent iron (Fe) and 0.6-0.8 percent phosphorus (P) or 10-20 times the acceptable phosphorus level. The phosphorus is intimately associated with the iron oxide and colloidal gangue, no discrete phosphorus minerals are found, and beneficiation is not possible. Therefore, to reduce the phosphorus, a hydrometallurgical process that includes roasting followed by leaching in dilute sulfuric acid has been developed. Phosphorus extraction is 70-90 percent, with only a minor loss of iron. The process has been tested in the laboratory and in a pilot plant at 50-300 kg/h. Construction of a 900,000 t/y demonstration plant is underway.

Jan 1, 2003

By Corby G. Anderson

Laboratory testing, interpretation and application of metallurgical technologies can be tedious, time consuming and costly. This paper outlines the use of proven statistical design of experimentation software for rapid optimization of laboratory testing and operating plants with limited representative sample utilization. This results in less costly required testing, a more thorough understanding of results and the ability to simultaneously optimize several variables and outcomes at once. At the Center for Advanced Mineral and Metallurgical Processing, this testing methodology has been used successfully in many metallurgical development and plant optimization projects thereby confirming its real world utility and application. Accordingly, several applied examples in flotation and hydrometallurgy will be outlined in this paper. This will include flotation testing of a copper gold ore, flotation testing of a copper, cobalt and gold ore, optimization of an industrial hydrometallurgical jarosite circuit and optimization of industrial nitrogen species catalyzed pressure leaching of a copper enargite concentrate.

Jan 1, 2006

By H. Kung, T. R. Jervis, M. Nastasi, T. E. Mitchell

"A systematic study of the structure-mechanical properties relationship is reported for nanolayered composites of MoSh-SiC, Mo-MoSh, Mo-MoShNx, MoSi2-MoSi2Nx, and Mo-MoShMoSi2Nx (x=3-4) synthesised by sputtering techniques. These composites have been studied by nano-indentation and cross-sectional TEM as a function of annealing temperature. As-deposited layers are amorphous except for Mo. With increasing annealing temperature, first MoSh and then SiC crystallize, while the hardness progressively increases until the layers start to spheroidize and grain growth sets in at 900ºC. For the case of Mo-MoSi2, the layers react and the composite deteriorates rapidly. However, MoSi2Nx remains amorphous up to 1000ºC, suggesting that it could act as a diffusion barrier between Mo and MoSi2. In fact the Mo. MoSi2Nx, MoSi2-MoSi2Nx and Mo-MoSi2-MoSi2Nx nanolayers are found to remain stable up to such temperatures. IntroductionMolybdenum dislicide, MoSh, is a potential matrix material for high temperature structural composites due to its high melting point and good oxidation resistance at elevated temperature [1]. The two major drawbacks for structural applications are inadequate high temperature strength and poor low temperature ductility. Silicon Carbide (SiC) being hard and thermally compatible with most ceramics and intermetallic compounds, has been found to be suitable for second phase reinforcement in various structural applications and, in particular, the addition of SiC whiskers improves the high temperature yield strength of MoSi2 [2]. While most of the research in MoSb-SiC composites has been on the particulate form of SiC, laminated composites may offer unique properties. It has been shown that synthetic multilayers with alternating layers of metal and/or compounds may exhibit interesting mechanical properties [3]. Enhancement in mechanical properties by decreasing the wavelength of multilayer spacing has been studied extensively. In general, two types of strengthening have been proposed: (1) Hall-Petch strengthening [4,5], where the strength increase is inversely proportional to the square root of the layer thickness; (2) Koehler modulus strengthening [6], which increases with modulus difference and decreasing layer thickness. In the present study, we have performed a systematic study of the relationship between strength and structure in a number of different nanolayered systems based on MoSh. Layer thicknesses have been varied and their nanostructures have been varied by heat treatment. Previous work on MoSi2-SiC is summarized [7]. In an attempt to improve fracture toughness, MoSh-Mo nanolayered materials have been prepared but are found to react and deteriorate. Previous work has shown that nitrided MoSi2 (MoSi2Nx with x=3-4) is highly stable [8] and so nanolayered composites of MoSi2-MoSi2Nx and Mo-MoSi2-MoSi2Nx have been prepared to assess the' stability and mechanical properties of these composites. Preliminary results are presented."

Jan 1, 1994

By Hans von Michaelis

There has been a renaissance in gold and silver extraction and recovery that has taken place over the last fifteen years, since the price of gold was freed from the $3510~ level. Despite major advances in such areas as carbon adsorption processes for gold recovery, refractory gold ore treatment, crushing and grinding, process control, etc., there still remain several gold and silver mineral processing frontiers. Frontiers related to environmental management present significant challenges especially in the USA. More than ever it is appropriate to optimize total economics by adopting a "systems approach" that integrates mining, mineral processing and environmental management.

Jan 1, 1993

By Xinghui Meng

The recovery of platinum and palladium from automotive catalysts has been investigated by leaching in iodide solutions with oxidants including oxygen and iodine in an autoclave. An ammonium salt was presented in a neutral leaching solution as a key leaching reagent to achieve high recoveries of the platinum group metals (PGM). The effect of temperature, and concentrations of oxidants and of ammonium salt on the recovery of PGM was examined. Under the experimental conditions studied, the recovery of platinum and palladium was found to be greater than 95%. An economical assessment of this process has also been examined and discussed.

Jan 1, 1995