Search Documents

By Liang Yu, Yuhua Li, Yuanchi Dong

"High alumina slag, with alumina normally more than 15 pct, is encountered with blast furnaces in China because of high alumina/silica ratio in iron ore as well as sinter and high ash content in coke for cost reason. High alumina slag with high viscosity and high liquidus temperature would lead to higher slag volume and thereby, furnace productivity. In the present work, liquidus temperature of high alumina slag, based on Meishan factory, Baosteel China, were investigated. A liquidus temperature model was introduced in the present work based on basic physical chemistry theory and focused on the chemical composition area used in Meishan factory(pct): Al2O3 from 14 to 17.5 and MgO from 8 to 12, so that the blast furnace slag could be designed for optimum blast furnace performance.IntroductionBlast furnace slag composition[1] has very important bearing on its physicochemical characteristics which affects smoothness of operation, slag handling, coke consumption, the degree of desulphurization, hot metal productivity and its quality etc. The slag properties which affect most are liquidus temperature, viscosity, sulphide capacity and alkali capacity. Variation of these slag characteristics with composition and temperature has been a field of active researches as these its great influence on the blast furnace operation. In the early years, most of these studies were carried out over low alumina blast furnace slags with alumina normally less than 15 pct. High alumina slag was first introduced in India because of its high alumina/silica ratio iron ore as well as sinter and high ash content in coke[2]. And then this problem becomes common as higher alumina/silica ratio iron ore imported and used [2-5]. The most important problem caused by high alumina content is liquidus temperature and then viscosity of the slag.Generally speaking those reported works [2-5] investigated a pretty wide range of chemical compositions and then obtained complex model, respectively. In fact, every factory has its own interest because of different resources. For example, the Al2O3 content from 20% to 30% pct was studied in Tata Steel India [2], but it is too high for Baosteel Meishan. A very lower percentage of alumina content, 14-18 % pct, was mainly used."

Jan 1, 2008

By Antonio de Lucas, Juan Francisco Rodríguez, Ignacio Gracia, Mª Teresa García

"The amount of waste of Polystyrene (PS) foams is increasing in last years due to their use in insulation, protecting and, storing many different food products. Conventional methods of recycling such as crushing and shrinking by heated air or frictional heat have the disadvantages of molecular degradation, resulting in a reduction of the quality of the recycled polymer. Dissolution and shrinking with suitable solvents is one of the cheapest and more efficient ways of polystyrene recycling but in the process of the solvent recovery by distillation a certain degree of molecular degradation is produced. In this way, CO2 supercritical technology appears as an interesting alternative for the elimination of solvent. This work proposes a global process to polystyrene recycling in two steps: a polystyrene dissolution with a suitable “green” solvent followed by its elimination by supercritical tecnologhy. In order to develop a “green process” the constituents of essential oils, limonene, terpinene, cymene, and phellandrene, are selected as the most appropriated solvents. Introduction In the last years, disposal of the non-biodegradable plastic wastes has been recognized as a serious environmental problem. Recycling these wastes has great interest in order to prevent the environmental pollution and to preserve natural sources (1, 2, 3). Since the Polystyrene foams (PS) is one of the most used foam in isolation, protecting and food storage most of recycling work is concerned with this polyolefin (4). The two main alternatives for treating polymer wastes are energy recycling, where wastes are incinerated, and mechanical recycling (5). Environmental argumentations such as toxic emissions are building up a public resistance against incineration process (6). Mechanical recycling is a popular recovery path for manufacturers and is carried out on single-polymer waste streams. Any way, the market for recycled products can only be found if the quality is close to that of the original. Unfortunately the process of classification and further recovery of these wastes makes them often more expensive than virgin plastic (7, 8). Solvent extraction is one of the cheapest and more efficient ways for PS recycling. If it is done in house of waste producers the separation between plastics could be easy and effective and the transport costs would be eliminated."

Jan 1, 2008

By Gerardo Muñoz

All along this century CODELCO's smelters have been operating on conventional technology, which Codelco has streamlined by using oxygen, developing oxy-fuel burners for reverberatory furnaces and introducing oxygen smelting of concentrates in converters (Teniente Converters). Chuquicamata began capturing sulfur from its first Teniente Converter in 1985. Since then, it has implemented a program allowing to gradually increase such capture. In 1994 a Frame Law on the Environment was enacted in Chile. By virtue thereof and of CODELCO's corporate environmental policy, an investment program aimed at capturing more than 95% of gaseous pollutants in all its smelters in a term not exceeding twelve years was established. The above entails a substantial improvement of the operational management as regards fugitive gases capture and treatment. This paper describes the way CODELCO is to deal with this challenge with a view to fully complying with environmental regulations and obtaining the required environmental certifications of its operations.

Jan 1, 1996

By Shunli Zhang

Metals recovery from electronic scrap by physical separation may provide an alternative to the current recycling approach, through which halogenated flame retardants can result in hazardous dibenzo-p-dioxins and dibenzo-furans. On the basis of a complete sink-float analysis of personal computer and printed circuit board scrap, and in view of the advantages of dry processes for electronic scrap recycling by mechanical separation, air table separation is prioritized in an attempt to separate metals from plastics and glass involved. In the present paper, theoretical and practical considerations of air table separation have been detailed. It has been shown that air table separation is effective for recovering copper and precious metals from this specific waste stream. With the feed rate of 60 kg per hour, the combined grade and recovery of copper, gold, and silver attainable for the two heavy products produced by the air table used in the present study was shown in the following table:

Jan 1, 1998

By Gavin Lind

The Minerals Council of Australia (MCA), through its Minerals Tertiary Education Council (MTEC), builds capacity in higher education in the core disciplines of mining engineering, metallurgy and minerals geoscience. Over the past fourteen years, this all-of-industry approach in securing the long-term supply of these critical skills (which remain a chronic skills shortage for the Australian minerals industry) through nationally collaborative programs across sixteen Australian universities delivers spectacular and sustainable results for the industry. These unique, world-first programs are built on a healthy platform of dedicated industry funding and in-kind support and forms part of the MCA’s broader uninterrupted, sustainable education and training pathway to increase workforce participation, workforce diversity and workforce skills, regardless of the business cycle in the industry. This paper will highlight the origins, iterations and current successful programs of MTEC, including its future vision, and presents a mechanism for industry and academia to collaborate to address future professional skills needs in the minerals industry globally.

Jan 1, 2014

By Youn-Bae Kang

In order to overcome weak points of steel for its engineering applications, in particular, for environmentally benign, energy-efficient, lightweight engineering systems, a number of new steels have been proposed, especially to improve strength-to-weight ratio (specific strength). Mass production of these steels, however, has encountered a serious roadblock particularly in the steel refining and casting processes. This is because their chemistries and cleanliness requirements are vastly different from those of the conventional steels, and thus an incremental improvement of the prevailing process technologies is found hard to meet the requirements. In this study, a new process is proposed, which employs inert gas bubbles in the shroud nozzle, liquid steel drops in the degassing chamber, and the siphon transport for continuous casting. The proposed process which integrates the final refining and cleaning steps prior to casting is expected to be a technologically disruptive innovation on the conventional counterpart. The effectiveness of the individual steps is discussed with experimental results.

By Mao Chen, Baojun Zhao, Zhixiang Cui

Bottom blown oxygen copper smelting process, operated at high grade matte (up to 75 wt% Cu) with relatively low (2-3 wt%) Cu in slag, has been commercialized for more than five years at Dongying Fangyuan Nonferrous Metals CO., Ltd. Quenched slag and matte samples have been collected at different operating conditions while the slag temperature was measured by thermocouple. The samples were analysed by X-ray Fluorescence and Electron Probe X-ray Microanalysis. FactSage computational software was used to explain the observations of the industrial samples. The analyses show that the copper loss was closely related to the operation parameters. The Fe/SiO2 in slag and temperature determine the solid proportion, which significantly affects the physical entrained and also chemically dissolved copper in the slag. The present study will be useful in understanding the slag chemistry of bottom blown copper smelting furnace and in optimization of the operating conditions to lower Cu loss in the slag.

Jan 1, 2015

By N. G. Azeredo

This work dealt with the evaluation of engineering structural clay brick samples that were sintered at estimated temperatures of 700 and 800°C. They were collected in a red-brick plant in Campos dos Goytacazes, RJ, Brazil. From a lot, a sample already sintered in its kiln at 700°C were collected and also a sample from the same lot only dried by the air, which were then sintered at 800°C controlled temperature. The samples were subjected to Brazilian Standard tests (ABNT NBR 15270:2005) to determine their geometric, physical and mechanical properties. In order to be classified as structural clay brick it is required minimum 3.0 MPa for the characteristic compressive strength (fbk) to be suitable for up to five floors structural building applications. We also used the Weibull Probability Plot and Weibull Maximum Likelihood Estimation to evaluate distribution parameters in order to compare the results of compressive strength obtained in the tests.

Jan 1, 2015

By A. Navarra

Within conventional copper and nickel-copper sulfide smelters, ladles of molten matte are fed into converters. These converters blast oxygen-enriched air into the matte, thereby eliminating iron and sulfur. The converting reactions are exothermic and, indeed, the converter heat balance is often a limiting consideration on the smelter throughput. If a portion of the matte were fed in solidified (granulated) form, this would support higher oxygen enrichment, and lower volumes of converter offgas, allowing higher throughput. This approach is not applied in conventional smelters, partly because of the copious amounts of water that must be evaporated in typical granulators, as in the Kennecott-Outotec process. The current paper recalls a waterless matte granulator that had been pioneered in the 1990’s, and is applicable to conventional smelters. A mathematical formulation is presented that can be used in the context of simulation-based optimization, to estimate the size and impact of waterless matte granulation.

By A. V. Tarasov

Based on the data available in the literature and the practical experience of new metallurgical plants, a method has been proposed and relevant studies conducted for metallurgical processing of zinc sulfide concentrates. Process conditions and parameters have been identified, which ensure high levels of recovery of zinc into solution. This is achieved by leaching concentrates under the normal pressure at a temperature of >90°C in the presence of ferric iron ions. Sulfide sulfur is converted to elemental sulfur in this process. To produce elemental sulfur it is necessary to maintain oxidizing conditions in the system, characterized by a positive Eh value. In order to eliminate the interfering effect of elemental sulfur formed in the process, it is possible to add surfactants into the concentrate pulp. The proposed technology has certain advantages as compared with the high-temperature pressure leaching and is considered as a basic technology to be applied to increase zinc production at one of the Russian zinc plants.

Jan 1, 2006

By M. Giunti, R. Hampson, S. Gray, P. Kapoulitsas, J. Clark

In 1997 Pasminco's Port Pirie Lead Smelter began a modernisation of its lead and precious metals refinery operations. Driven by the anticipated closure of its Broken Hill mine, the new refining process replaced the locally developed continuous process, which had been in operation since the 1950's. Commissioning of the new plant was staged, beginning in late 1997, and finishing early in 1999. The new plant provides for batch refining of lead, and the use of vacuum induction retorting and bottom blown oxygen cupel technology in the silver refining area. The project has resulted in an increase of lead production capacity of 11% and allows the treatment of a wider range of concentrates than was formerly possible. The most significant change has been to double the smelter's silver capacity to over 400 tonnes per annum. This paper describes the successful implementation and optimisation of the new refinery, which is now consistently meeting design capacity.

Jan 1, 2000

By G. Roy Chaudhury

Adsorption techniques are comparatively low cost and effective for treatment of arsenic contaminated drinking water. Various adsorbents such as alumina, ferrihydrite and manganese ores have been used, but there has been little investigation of modifying the structure of ferrihydrite to improve its adsorptive efficiency of As(III) and As(V). In the present study the incorporation of manganese oxide into the ferrihydrite structure was carried out and the prepared materials used in arsenic adsorption experiments. The compounds were X-ray amorphous, but TGA/DTA and FTIR analysis showed some structural characteristics. Sorption studies reported in this paper indicate the excellent arsenic removal properties of the manganese/iron compounds with a loading capacity of 0.3 mmol/g. Adsorption follows first order kinetics and the results fitted to adsorption and mass transfer models. Arsenic levels in water containing 1 mg/L As(V) were reduced by 50% in 20 minutes and 90% in 60 minutes using 1 g/L manganic ferric oxyhydroxide.

Jan 1, 2003

By O. I. Platonov

The experience that has been gained by MMC ?Norilsk Nickel? at its Trans-Polar Division (PD) operations since 1981 in the field of recovery of elemental sulfur from off-gas generated by the Vanyukov and flash smelting through its reduction by natural gas is briefly outlined in the present paper. The key challenge the operators treating off-gas originated from autogenous smelting are usually faced with is the presence of sulphur trioxide in it. Furthermore, air inflows along the entire gas flue increase oxygen concentration in off-gas, thus leading to over-consumption of the reducer (natural gas). Another issue attached to the methane technology is a low yield of hydrogen sulphide largely preventing efficient downstream Claus conversion of the gas. The new flowsheet for treatment of autogenous smelting off-gases including dry dust-cleaning followed by the gas reduction in homogenous reactor developed by OAO Gipronickel Institute on the basis of industrial-scale production of elemental sulfur in Norilsk is presented.

Jan 1, 2006

By Ian M. Ritchie

Right across the universities of the developed world, the traditional disciplines of physics and chemistry are losing ground. Extractive metallurgy, which depends so heavily on chemistry, is also contracting despite a clear need for people with this kind of training in the mining industry. Reasons for this loss of popularity are discussed in this paper. High on the list is one of image. The extraction of metals is widely seen as a dirty, polluting, sunset industry which involves working in remote and uncomfortable corners of the earth for inadequate compensation. Ways in which the image problem can be overcome are considered. It is concluded that a concerted effort needs to be made by the universities and industry to redress this situation. The importance of extractive metallurgy, both now and in the future, when a greater emphasis will be placed on sustainability and recycling, needs to be stressed. In addition, courses need to incorporate training for a career path that leads on beyond extractive metallurgy.

Jan 1, 2003

By Tong Deng

Clean processing of copper converter slags for reclaiming cobalt and copper could be a challenge. An innovative and environmentally benign approach for recovering metal values from such a slag was developed in the present work. Curing the slag with sulfuric acid, without re-smelting or roasting as currently practiced in the industry, made it amenable to leaching, and more than 95% of the cobalt and up to 90% of the copper was extracted, together with iron, by water leaching, leaving silica behind in a residue. Copper in the leach liquor was recovered by cementation with iron, and the dissolved iron crystallized as ferrous sulfate monohydrate. Cobalt in the pregnant solution rich in iron was recovered by either cementation or sulfide precipitation. Chemical and mineralogical characterization of the slag and its products were examined and compared to determine the nature of the changes occurring during curing and leaching. Operating variables were also investigated and optimized.

Jan 1, 2003

By Freddy Syvertsen, Ali Riza Tarakcilar, Engin Tan, Derya Dispinar

"It has been shown that the disturbance of the advancing liquid front in the mould cavity may lead to surface entrained defects known as bifilms. These defects can deteriorate the mechanical properties significantly. The developments in the simulation of castings aid many casters. It is quick and economical. Therefore in this work, the aim was targeted to optimise the mould filling of a tensile test pattern design that is used for aluminium alloys. Several different designs, gatings and runner systems were investigated with Vulcan Casting Simulation Software. In addition to the achievement of non-turbulent and quiescent mould filling; other parameters such as temperature profile, porosity and feeding were investigated to optimise the process.IntroductionConsiderable effort has gone into understanding and controlling defects that are formed in aluminium and its alloys during casting. The conventional approach was the elimination of porosity by eliminating hydrogen in the melt simply due to the following reaction:"

Jan 1, 2012

By Clodualdo C. Conde

In order for Philippines Associated Smelting and Refining Corporation (PASAR) Corporation to remain a leader in the copper smelting and refining industry, continuous improvements in plant technology are required. Reliable performance of plant equipment is essential for a competitive smelting operation. PASAR is constantly searching for the best equipment and technology to allow us to manufacture products more efficiently. When the Smelter was commissioned in 1993, the Flash Furnace off-gas treatment system was a constant source of problems. There were frequent shut-downs of the electrostatic precipitator due to material buildups on the discharge electrodes and collecting plates. In 1998, the precipitator was successfully upgraded to eliminate the buildup problems and to increase the collection efficiency. The upgrade greatly reduced down time and maintenance, and the enhanced collection efficiency also eliminated pluggage problems and material losses in the Acid Plant. This extensive precipitator upgrade was accomplished during a 30-day Smelter turnaround.

Jan 1, 1999

By E. Burgos Cruz

The behaviour of S, N and P during refining of Fe-18 wt%Cr-10 wt%Ni with calcium carbide was investigated. The effects of the initial contents of C and N in the metal phase, as well as the supply method of calcium carbide to the melt on the removal degrees of S and P were evaluated. Heats were carried out at 1873K, in MgO crucibles, using a laboratory induction furnace. It was observed that simultaneously with S and P, N and O have also participated in the reactions. It seems that, in fact, O governs the behaviour of the other elements dissolved in the melt and that N is had to the removal of P with calcium carbide. It was also noticed that high C content in the metal phase have not altered the dephosphorization and desuffirization degrees, but that the supply of calcium carbide done by injection led to a lower dephosphorization degree than the one obtained by dumping it.

Jan 1, 1995

By Toshihiro Tanaka

The information on viscosity and surface tension of molten slag is indispensable to design new refining procedures in ferrous and non-ferrous processes. For example, the authors have tried to develop "Capillary Refining" to remove impurities in liquid metals by applying capillary absorption of molten slag with those impurities into solid fluxes which have a lot of small capillary tubes. It is necessary to adjust the above physico-chemical properties to adequate conditions on the capillary penetration. In the present paper, we discuss our recent trial to predict surface tension and viscosity of molten slag in multi-component systems. We have derived a thermodynamic model to predict the surface tension of molten slag by using ionic size, molar volume and surface tension of pure components. In addition, we have applied neural network computation to evaluate the viscosity of molten slag. We found good agreement of the calculated results with experimental values of the surface tension as well as the viscosity in various slag systems.

Jan 1, 2006

By Chai Liyuan

This paper focused on the preparation of porous ceramic pellets for microorganism carriers. A new method for the process was developed using simple gel-casting and bubble-in-water-in-oil type of multiphase double emulsion. The globules, consisting of a foamed sepiolite slurry suspension, were dispersed and consolidated in spherical shape in liquid paraffin as gelation progressed. The green pellets were sintered at 1100°C. The influence of surfactants, extension ratio and impeller revolution rate on the process and characteristics of the pellets was investigated. The pellet size was in the range of 1~4mm and determined directly by impeller revolution rate. The fine cell diameter of porous ceramic was in the range of 100~500m and the micropore diameter was less than 5m. The inner macropores were interconnected and extend to the external surface. It is impossible to analyze a result by SEM micrographs and digital camera.

Jan 1, 2006