Search Documents

By Yuanbo Zhang, Qian Li, Helei Zhang, Heng Yu, Guanghui Li, Tao Jiang

"Large reserves of specularite iron ores have been found all over the world, which is characterized by high total iron grade, low gangues content, as well as low commercial price. However, it has not been widely used in sinter or pellet production due to its inferior sintering and roasting behaviors. It has shown that the proportion of specularite ores was increased as high as 40%~50% and good results was achieveed by using Composite Agglomeration Process (CAP), an innovative agglomeration process invented by Central South University. But the mineralization of specularite is still unknown during composite agglomeration processing. In this paper, the induration characteristic of specularite ore is studied by simulating CAP in laboratory, as well as microstructure analysis of CAP product. The results show that specularite pellet is mainly indurated through recrystallization of Fe2O3, calcium ferrite within high basicity sinters matrix interweaves with the recrystallized Fe2O3 on the surface of the pellet, which forms an integral microstructure, and ensures high strength of CAP product for ironmaking.IntroductionLarge reserves of specularite iron ores have been found all over the world, especially in Minas Gerais of Brazil, Xuanhua city and Anshan city of China, Elba island of Italy, St.Gotthard of Switzerland, Cumberland of Britannic, and so on. The specularite ores have a smooth surface, as well as a good crystallization and dense texture. When specularite is used to produce pellets, the specularite ore grains are difficult to adhere onto green ball due to its poor ballability. Moreover, specularite pellet requires high roasting temperature over 1300°C [1]. When specularite ore is used in sintering, the permeability of sintering bed gets bad and the quality of sinter is diminished. The practice in a few sintering plants finds that the output and strength of sinter decrease with the increase of specularite proportion, and the consumption of coke increases [2-4]. Therefore, the utilization of specularite has been limited. Composite Agglomeration Process (CAP) is an innovative technology invented by Central South University [5-7]. The process has the following merits: making reasonable utilization of different iron ore resources; improving the quality and output of sinters; manufacturing sinters with low basicity; significantly reducing energy consumption, etc[8-9]. It has been shown that large proportion specularite ores, as high as 40%~50% can be used well by CAP [10], but the mineralization of specularite pellet is still unknown during composite agglomeration processing. In this investigation, the induration characteristics of specularite ore pellets is studied by simulating CAP in laboratory, and the phase composition and microstructure of CAP product are also characterized by using microscope and Leica image analyzer (Germany, Leica DM RXp)."

Jan 1, 2011

By K. Noda

Tamano Smelter of Hibi Kyodo Smelting Co., Ltd. started its operation adopting the Flash Smelting Furnace with Furnace Electrodes (FSFE). Thereafter, it developed a coke combustion technology based on C() concentration control, which made possible a low cost and high productivity operation without using electrodes. However, increase of treated concentrates and upgrading of matte grade for production expansion started to cause difficulties in operation control with then existing operation control system. This paper outlines recent improvements for stable operation of the Tamano Type Flash Smelting Furnace (T-FSF), such as computer aided operation guide system.

Jan 1, 2001

By Li Kaihua, Li Liang, Miao Qingdong, Wang Cong

The current process of production of titanium sponge involves the use of TiCl4 as a feed material and a huge amount of heat is generated during the magnesiothermic reduction process. For this reason, it is possible to agglomerate into a titanium lump with the partial high temperature. And, it is difficult to obtain soft titanium sponge with low content of impurities. In order to solve the current problems in the titanium sponge production process, process optimization experiments study of TiCl4 feeding speed, vacuum distillation temperature, system pressure and time control had been conducted for obtain high quality titanium sponge. Experimental results show that lower feeding speed can improve the output capacity of titanium sponge and softer products can be obtained. The product grade rate of titanium sponge improved significantly.

Jan 1, 2015

By E. M. Weenink

One of the new direct smelting technologies for the production of lead from sulfide concentrates that has reached the commercial stage is the Outokumpu lead flash/electric furnace ?smelting process. Using data from pilot plant test work, energy and mass balances for a commercial plant were initially calculated by hand. To optimize process conditions, a large number of such balances had to be generated and a computer program using Lotus 123 was developed which provided an excellent opportunity for computer simulation. Operating parameters can be calculated by iteration using input values for feed composition, feed rate, smelting temperature, and lead content of the slag'" The output is presented by means of various views of the appropriate process steps, or in 68 different graphs.

Jan 1, 1990

By Susumu Okabe

Injection metallurgy is widely adopted in various fields of metallurgical operations to achieve high productivity. The Mitsubishi Continuous Copper Smelting and Converting Process employs the top blown lance technique for the continuous supply of solid charges and reaction gases into the molten bath, where the agitated bath contributes to enhance the heat and mass transfer and the increased gas/liquid interface area accelerates the reaction. However, excessive splashing of the molten materials accompanied by the injection may cause an unexpected wear of the furnace lining. In order to estimate the splashing rate quantitatively, and to optimize the furnace design and the blowing condition, a physical model study of the top blown gas injection onto the liquid bath was carried out. An equation of the splashing rate was obtained as the function of cavity size, gas velocity and bath properties.

Jan 1, 1995

By John E. Litz

The Denver Process is a chemical/metallurgical process for treating radioactive or mixed wastes by extraction and concentration of the radioactive and/or hazardous component(s). The process was developed at bench scale, evaluated at pilot scale, and will be implemented at full scale to remediate a low-level radioactive sludge. Six unit operations comprise the process: feed handling, leaching, solvent extraction, electrodeposition, precipitation, and tailing preparation. Unit operation design may be modified to tailor the process for varying feed stock composition. Radioactive or mixed waste is reacted with aggressive reagents in an aqueous phase, solubilizing targeted components. These components are then selectively extracted and concentrated in subsequent steps. Waste solids and solution exit the process as non-hazardous non¬radioactive waste. Dehydration of aqueous waste by submerged combustion eliminates aqueous discharge.

Jan 1, 1994

By M. Vondersaar, B. Bulnes

Quemetco, Inc.,. as a subsidiary of RSR Corporation, operates one of RSR's three secondary lead smelters in the City of Industry, California, next to a residential area within Los Angeles County. The Reverberatory furnace serves as the main reactor for melting lead grid and paste recovered by the battery crushing system. Feed material is introduced via screw conveyor after drying in an upstream rotary kiln. Slag produced by the Reverb flows directly to an electric arc furnace. Products from this one-pass furnace system consist of soft lead bullion from the reverb, hard lead bullion from the arc furnace, and a non-hazardous slag from the arc furnace. Furnace bullion is processed into finished product in a six-kettle refinery. An overview ·of plant operations is presented. Where applicable, references will be made to changes that have taken place during the last decade.

Jan 1, 2000

By James T. Skoch

With the ongoing pressure on the secondary aluminum business to limit the amount of waste generated from processing aluminum dross, it becomes very advantageous to preprocess the dross to reduce waste. The advantage of preprocessing is that it significantly reduces the oxides and salt cake generated when melted. Various products can be produced from the oxides for the steel industry. The following paper will demonstrate that removal of oxide fines before melting will result in large volumes of material not being landfilled. We will show that the end result of this technology is to significantly reduce the amount of salt cake sent to a landfill while maximizing the recyclability of the aluminum dross.

Jan 1, 1995

By Masayuki Kudoh, Tohru Maruyama, Yohichi. Ito

When hypo-peritectic carbon steel is quenched during unidirectional solidification, the region of fine columnar grain is observed. It is classified into two coexisting phases. One is coexisting phases of liquid, delta and gamma in the upper part of the region, and the other is coexisting phases of delta and gamma in the lower part of the region. To form the coexisting part of the three phases means that solidification in this experiment proceeds in non-equilibrium state. The size of the narrow side of one fine columnar grain coincides with the arm spacing of a primary dendrite and this result is the same as the hyper-peritectic carbon steel. However, the boundary of the fine grain in the hypo-peritectic carbon steel is formed in different location from that of the hyper-peritectic carbon steel. The former is formed in the skeleton of the dendrite, while the latter is formed in the interspacing of the dendrite. The region of the fine grain changes suddenly to that of the coarse grain when the delta phase in the coexisting part of two phases disappears completely. Therefore, the delta phase in the hypo-peritectic carbon steel might prevent the growth of gamma grain. In order to recognize it, ferrite formers such as Mo, V and Ni are added in the sample. Then, the longitudinal length of the fine columnar grain extends in the sequence of the no addition, Mo, V and Nb.

Jan 1, 2000

By Richard D. Hagni

The United States is dependent upon foreign sources for more than 93% of its bauxite and alumina supply. Domestic production of bauxite, which comes from Alabama, Georgia and Arkansas, is limited to those bauxite ores containing less than about l ½ % iron. Bauxites with higher iron contents are generally not utilized because they cause problems in bauxite calcining and especially because they produce undesirable brick discoloration and cracking. In order to improve beneficiation and expand the utilization of high-iron or ferruginous bauxites, a mineralogical and textural study has been conducted on selected samples from the Eufaula, Alabama, bauxite district. Reflected light microscopic, petrographic, and X-ray techniques have shown that a variety of iron minerals are present, including hematite, goethite, lepidocrosite, siderite, pyrite, marcasite, and ilmenite. Although the iron minerals may be locally concentrated into concretions and pisolites, most occur as very fine grains that are disseminated and show a variety of intergrowths. Mineralogical and textural observations indicate that the fine-grained iron mineral grains may be amenable to high gradient magnetic separation.

Jan 1, 1981

Studies of electric pulse (EP) disintegration were conducted on ores of disseminated precious minerals, 'on platinum-bearing chromitites of the Konder Complex, Russia, on diamond-bearing impactites of the Popigai meteoritic crater, Russia, and on and diamond-bearing metamorphic rocks of Northern Kazakhstan. It was shown that EP disintegration ~s a technology that achieves ideal liberation of disseminated minerals, and is a new efficient method to study accessory minerals.

Jan 1, 1991

By Truan-Sheng Lui, Li-Hui Chen, Fei-Yi Hung, Cheng-Yi Chen

"This research used the austempering heat treatment on the SCM435 thin specimen with a type of double loop and obtained the Cr-Mo bainite structure, and then we could further investigate the mechanical properties of SCM435 bainite structure. Experimental data showed the stability of the mechanical properties of specimen with austempering temperature 830°C for 25 minutes was better than that of 15 minutes. The size of austenite grain affected the strength of thin specimen. After austempering at 830°C-25minutes and salt bath at 290°C, the stability of UTS was better than that of salt bath at 310°C and 330°C. The average hardness of all specimens was about more than HRA70. The specimen with austempering at 830°C-25minutes and salt bath at 290°C-30minutes had bigger grain size of austenite and retained y, it also had higher hardness and strength toughness. So, its stability was improved for tensile strength comparing with traditional tempered martensite process.IntroductionSCM435 is a Cr-Mo steel with high strength and high hardness properties, and it has been widely used in machine parts, shafts, gears and strength screw products [1-3]. However, this system often has lower reliability due to the brittleness of high-temperature tempering and quenching inequality. Considering the austempering heat treatment can obtain the uniform bainite structure to improve the temper brittleness, and the austempering heat treatment is a continuous process that it also has efficiency and uniformity. For the thin plate specimens, the mechanical properties of the bainite structure are better than traditional martempering structures."

Jan 1, 2013

By Lv Guozhi, Niu Liping, Liu Yan, Zhao Qiuyue, He Jicheng, Zhang Ting’an, Dou Zhihe

"This paper proposed a new method of Mg and Cl2 circulating for titanium sponge production by direct pyrolysis and thermal reduction process. Effects of pyrolysis temperature, pyrolysis time and partial pressure of oxygen on pyrolysis efficiency were researched, and the crystallite structural transformation of MgO productions at different pyrolysis temperature and time were analyzed by XRD. The experimental results indicates that the pyrolysis temperature and time effects the pyrolysis efficiency obviously, and the reasonable pyrolysis conditions by using MgCl2 in molten state are as follows: the pyrolysis temperature is 1100?, pyrolysis time is 60min and the partial pressure of oxygen is 100%, the pyrolysis efficiency get above 95% at this conditions. The dynamic analysis of molten magnesium chloride pyrolysis reaction shows that, as a chemical reaction process control, the response of the apparent activation energy Ea=70.4 kJ/mol.IntroductionTitanium is a young metal, it is applied in industrial until the Second World War. It is 160 years from the discovery of titanium to the industrial production of ductility titanium by magnesium reduction method in the United States in 1948. As a new kind of metal, titanium and titanium material are better than the traditional metal materials in mechanical properties, heat resistance and thermal conductivity. Titanium is a kind of landmark structure and function material, which is called “space metal”, “Marine metal”, “Intelligent metal” [1-3]. Although the study of new methods of titanium melting get more at present, Kroll method and Hunter method are really applied to industrial production methods for titanium smelting, and Hunter method is already discontinued because of costs at present. The core technology in Kroll method of sponge titanium production process can be ome down to two circulation, namely the cycle of magnesium and chlorine in preparation-process of titanium sponge. In the traditional Kroll method, the cycle is realized through magnesium chloride which is produced by the electrolytic magnesium reduction process in hot molten state. But because investment of equipment for electrolysis method is too high, this method has not been used by most titanium sponge production enterprise in China. At present most titanium sponge production enterprise in China produce titanium sponge by the outsourcing of titanium tetrachloride, but the main disadvantage of this method is that the by-product of magnesium chloride is difficult to deal with."

Jan 1, 2012

By Dumitru Mitrica, Vasile Soare, Elvira Alexandrescu, Mihai Ghita, Marian Burada, Petru Moldovan, Raluca Maria Florea

"Aluminum metal matrix composite Al-Si /SiCp was prepared by reactive gas injection and subsequent remelting. The influence of the remelting process on the microstructure and physicalmechanical properties of the resulted material was investigated. Samples resulted from the synthesis process contained silicon carbide agglomerations in the vicinity of primary silicon and large pore concentrations. In-situ formed silicon carbide presented mostly a polymorphic structure with particle sizes varying from 1 to lOµm. Physical and mechanical properties were largely influenced by the porosity distribution. The remelting process provided a decrease in the composite material porosity and pore size, with significant improvements in the particle distribution and physical-mechanical properties of the composite material. Additions of up to lwt.%Mg in the starting alloy improved the in-situ carbide formation and particles distribution in the solidified material. However, stable and large particle agglomerations were detected in the material in absence of conventional stirring or controlled solidification techniques.IntroductionThe remarkable properties of composite materials (yield strength, stiffuess, hardness and resilience at a reduced specific weight) make them attractive for applications in automotive, aerospace and military industries. Particle reinforced aluminum metal matrix composites (PAMMC) are known for their high strength to weight ratio. The recent development of P AMMC created the possibility to obtain large particles concentrations, exceeding 10% by volume ofreinforcement (SiC, AIN, Al203, etc.). The improvement ofhigh temperature strength and wear resistance made them appropriate for the use in automotive applications, such as the pistons, rotors, disc brakes, and propeller shafts [ 1]. The present main disadvantage of the P AMMCs is their high costs for obtaining and processing related to the final product performance. In order to benefit from the advantages that offer composite materials properties a reasonable production cost - performance ratio must be obtained [2]. Recent innovations in the manufacturing of aluminum-based metal matrix composites provided notable performance improvements but no feasible solutions were found for lowering their present high prices."

Jan 1, 2014

By R. M. Reynolds

Engitec Impianti, S?.p.A. of Milan, Italy has successfully designed, constructed and has in operation state-of-the-art battery breaker systems at two European locations. A third facility i:s partially completed in Toronto, Ontario, Canada. The CX system crushes whole batteries, separates the various components and desulfurizes the battery paste. The system also produces sodium sulfate from the sulfuric acid and lead sulfate contained in the batteries. Actual plant operating data indicates that the desulfurized paste contains less than 0. 6 percent sulfur and less than 0. 5 percent antimony. The CX system utilizes mechanical screening and an up-flow hydrodynamic separator to accomplish the component separation. Sodiwn hydroxide or sodium carbonate is used for desulfurization. The sodium sulfate brine is evaporated and crystallized to produce clean anhydrous sodium sulfate suitable for use by detergent or glass manufacturers. Plant data also indicates that an increase in furnace productivity of about 25 to 30 percent is achieved using feed from the CX system. The desulfurized paste is very suitable for electrolytic processing as an alternative to pyrometallurqical processing.

Jan 1, 1990

By Yanlong Li, Lifeng Zhang, Ying Ren

In this work, a multiphase mathematical model for the fluid flow in argon-stirred steel ladles was established and validated by experimental measurement of wood's metal. Alloy dispersion in the molten steel was calculated. The melting and mixing of alloy was faster with smaller size of the alloy particles, larger superheat and bigger slip velocity. The current mixing time is approximately 300 s with 30 mm alloy diameter and 91.5 K superheat.

Jan 1, 2014

By Gus Van Weert

The cost of oxygen is a major and common factor in the hydrometallurgical processes developed or proposed tor the oxidation of refractory pyrites. This cost involves charges for the generation and the transfer of the 02 to the mineral slurry. Bio-oxidation faces considerable design demands which require large scale equipment to be resolved. Nitric acid assisted oxidation offers low cost oxygen units; this method of pyrite oxidation deserves a closer look for large scale plants treating pyritic gold ores and concentrates.

Jan 1, 1990

By George J. Karcas

"Non-ferrous metals such as copper, nickel, lead, zinc and precious metals are produced via the electrorefining and electrowinning processes. Apart from controlling electro-chemical conditions for the production of these metals, there has always existed the challenge of controlling the corrosive effect of the electrolyte environment which serves as the medium for non-ferrous metal production.The practice of acid containment in electrometallurgical operations has entered the world of high technology with the advent of advanced acid resistant materials such as vinyl ester resin which is either combined with aggregate to form polymer concrete or used to line various acid containment vessels and ·surfaces. ill comparison to some Asian, European, and African copper refineries, the North and South American copper industry has recently embraced quite heavily in the use of polymer concrete electrolytic cells and process vessels, such as electrolyte storage tanks, and in the use of vinyl ester resin for corrosion protective surface sealing 'systems in lieu of epoxy, acrylic and other materials because of its combination of higher corrosion resistance and superior flexibility.Electrolytic cell construction has undergone a transformation from a multiple part configuration to a single piece moulded/cast unit. ·The one piece moulded polymer concrete cell, which has been patented by Corrosion Technology International, with the overflow, decant, inlet, fast fill and segregation systems integrally designed is now the industry standard.. The combination of a wood, steel, or concrete frame with a lining made of lead, asphalt, rubber or plastic has been historically successful in providing limited protection from chemical and mechanical attack in electrolytic cells and electrolyte storage tanks all over the world. These combinations have now become obsolete as materials such as polymer concrete provide exceptional corrosion and mechanical protection with greatly reduced maintenance requirements and improved efficiency and productivity for the tankhouse. ill addition, polymer concrete can be disposed of in a regular land fIll which is much less costly than disposing of contaminated concrete that is normally associated with conventional lined concrete cells."

Jan 1, 1997

By Li Xi

This paper describes how a back-propagation neural network is built for predicting the properties of engineering materials from their other properties, compositions or processes. A predicted result of the impact toughness of a 12Cr-2Ni-1.5Mo stainless steel from its tempering temperature is presented. Furthermore, the combination of this neural network for prediction is able to supplement the unpredictability of the expert system outside its domain of expertise. An integrated system may perform more intelligently and solve more complex problems as well as human expert, in some case even better.

Jan 1, 1992

By L. H. Gevantman

A program for the compilation of evaluated physical and chemical numerical properties data is being pursued at the National Bureau of Standards within the Office of Standard Reference Data. This program is being sponsored by the Department of Energy and managed by the Battelle Office of Nuclear Waste Isolation in Columbus, Ohio. The intent is to assemble a reliable body of numerical properties data concerning candidate mineralogical materials in which high-level radioactive wastes are to be buried. The ready accessibility of the data to site designers and the credibility achieved through the evaluative process are designed to help assess and compare the feasibility of each candidate material for use as a disposal site. Both generic and site-specific data are to be assembled. To date, generic rock salt properties have been assembled and published by the NBS as NBS Monograph 167. Details of the effort to produce this book are discussed.

Jan 1, 1982