Search Documents

By J. H. Ahn, J. K. Yoon, Jung-Eui Lee

"A concentration change during grade transition operation in steel thin slab casting is predicted with computer simulation, water model and plant trial. Fluid flow and mixing patterns in various tundish levels and flow rates were analyzed through three-dimensional mathematical modeling. Comparing with water model experiments, a simple, efficient and accurate computational model has been suggested to predict the concentration profile at outlet of tundish. Based on the model, mixing in/below the mold was analyzed considering EMBR. The predicted concentration profiles show good agreements with the measured values. It is found that the lower vortices in the mold are suppressed by the electromagnetic field and the plug-like flow region develops which decreases the intermixing of two different grades of steel and shortens the length of transition region.1. IntroductionContinuous casting is the primary mode of production of semifinished steel products as it offers tremendous advantages in terms of energy savings, increased yield and higher productivity over the traditional ingot casting process. Efforts have to be made constantly to improve the quality of the cast product, reduce costs and thus increase the competitiveness of the steel manufacturer. One way of reducing costs is to reduce the amount of intermixed steel during the grade transition operation.Several different procedures exist to handle the casting of dissimilar grades for the conventional slab casting. Each procedure has its own merits and demerits. In order to choose the best method for a particular operation, there are a lot of researches. In the case of present continuous thin slab casting of POSCO mini mill, the only possible method is to change ladle during the grade transition. Due to the high casting speed (3.8m/min-4.4m/min) it is impossible to change the tundish and due to the thin thickness of slab it is also impossible to insert grade separator."

Jan 1, 2000

By Hector Carreon

This paper presents experimental data for the magnetic field produced by thermoelectric currents around uncracked hard-alpha inclusions in a Ti?6Al?4V specimen under external thermal excitation for different nitrogen content ranging from 1.6% to 5.9%. According to our preliminary results, the magnetic flux density measurements were found to be rather sensitive to changes in nitrogen content with the exception of the intrinsic material background magnetic signal that affected deeply the detectability of inclusions and imperfections in non-contacting thermoelectric measurements. Hopefully, these preliminary results can help identify a non-destructive test method that can detect material inclusions with a level of nitrogen that could be detrimental to Ti?6Al?4V alloy components.

Jan 1, 2009

By Stephen W. Paff

The EPA has estimated that there are over 3,000 sites across the United States contaminated with lead. Techniques to remediate these sites include standard stabilization/disposal technologies, reclamation of lead using secondary lead smelters, soil washing, and biological removal technologies. In this paper, the current technologies used for lead remediation will be reviewed. Factors affecting the use of each technology, such as range of applicable concentrations, soil types, interferences from other contaminants, economics, and current technology status will be assessed. The paper will also focus on the results of a recent study completed by the Center for Hazardous Materials Research (CHMR), in conjunction with a major lead smelter, which demonstrates that secondary lead smelters may be used economically to reclaim lead from a wide range of lead-containing materials frequently found at Superfund sites. Such materials include battery case materials, lead dross, and debris containing between 3 and 70% lead. The results of development work completed by CHMR on the Acid Extraction Treatment System (AETS), which has been demonstrated to extract Lead from soils containing up to 30,000 mg/kg lead, will also be presented. The use of these technologies will be compared with other options for the remediation of sites.

Jan 1, 1994

By cheng Peng-fei, TANG Hai-yan, guo Xiao-chen, LI Jing-she, Liang Yong-cang, Zhao Baojun

In the process of oxygen blast furnace, the lower coke ratio and the higher coke load make the skeleton coke more important. To understand the dissolution of coke in melting and dropping zone, the influence of FeO content, temperature and reaction time on the dissolution of coke with slag were studied by single-factor experiment. Meanwhile, the three factors and three levels orthogonal were conducted. The dissolution degrees were characterized by the weight loss ratio and diameter variation. The results showed that the weight loss ratio increased and the diameter decreased with the increase of FeO content, temperature and time. The three factors and three levels orthogonal test showed that time was the most significant factor on coke dissolution, FeO content of the second, and finally the temperature. The microstructure of coke after reaction indicated that the dissolution occurred on coke surface.

Jan 1, 2016

By Dengfu Chen, Mujun Long, Youguang Ma, Xin Xie, Xing Zhang, Leilei Zhang

"Processing parameters of a submerged entry nozzle (SEN) affect significantly on the patterns of fluid flow and temperature distribution in beam blank continuous casting mold with double SEN s. Effect of the geometry structure and immersion depth of double SEN s on the fluid flow in beam blank continuous casting mold was studied by water modeling. Results showed that, the optimal nozzle inner diameter was 40mm, and immersion depth was 70-90mm. The mold surface fluctuation, slag distribution, impact depth and removing rate of inclusion particles were discussed under different processing parameters of double SENs. As the results indicated, slag distribution was more non-homogeneous with a higher casting speed. The results provided basic data for the design and optimization of SENs used in beam blank continuous casting mold.IntroductionNear-net-shape casting has the distinct advantages of less rolling procedures, higher metal recovery and lower energy cost. Therefore, in the recent decades, one of the recent trends in the steel making process is moving toward near net shape casting. in which beam blank casting is a typical technology. The schematic section of beam blank is shown in Fig 1."

Jan 1, 2014

First, a classification of the various primary sources of feed materials for the production of cobalt is presented from a mineralogical point of view : sulfides, arsenides, sulfo-arsenides and oxide minerals. Each of these cate- gories will be characterized by its behaviour towards concentration methods, taking account of the presence of the associated minerals of other metals and of the nature of the gangue minerals. Then, for each category of cobalt bea- ring ores, typical flowsheets of treatment will be presented and discussed and the characteristics of the cobalt concentrates produced will be under- lined having in view their subsequent processing by pyro - and (or) hydrome- tallurgical methods.

Jan 1, 1988

By Wei-Tong Du, Zheng-Lei Guo, Yu Wang, Shu-Chao Wang

The influence of bottom blowing a CO2–O2 mixture on the bath temperature of a vanadium extraction converter was studied by using the characteristics of CO2 with weak oxidizing. It was studied in two aspects: oxygen content and temperature. The experiments showed, when the ratio of the mixture of CO2–O2 was 2:8 at 1300 °C, the bottom blowing of the converter inhibited the heating up of the hot metal, thus keeping the temperature below the carbon vanadium transition temperature. At 1360 °C, the sensible heat absorption by CO2 was 1.44 times that absorbed by O2 per mole. Meanwhile, at 1300 °C, 20% CO2 released the chemical heat of 13.58 kJ. So with the increase of the CO2 ratio, the bath temperature was reduced. The research showed that the bottom blowing of a CO2–O2 mixture had an advantageous effect by decreasing the temperature of the vanadium extraction converter.

Mar 1, 2018

By Shengli Wu, Mingyin Kou, Laixin Wang, Xinliang Liu, Zhennan Qi, Yujue Wang

Softening and melting experiments were conducted on four kinds of imported lump ores named A-D, under different temperature intervals within the self-developed visualization high temperature furnace. By calculating the reduction and shrinking degree under different intervals, softening and melting indexes were determined. These ores all expanded firstly followed by shrinkage with the temperature increasing. The difference of lump ore’s own characteristic led to different softening and melting behavior. The results showed that the looser the structure was, the better the reducibility will be. The compact structure and good reducibility led to high expansion rate. The beginning softening temperature declined and the ending softening temperature increased because of high porosity, which resulted in wide softening temperature interval. The charging ratio of lump ore A should be improved. Lump ore B should be distributed in the center of the blast furnace. Lump ores C and D should be used less.

Jan 1, 2016

By Liu Wei-feng

In this paper, the practice of separating precious metals from base metals in gold-antimony alloy by selective chlorination leaching under controlling potential in China has been introduced in detail. The precious metals and the base metals can be separated completely when the complex gold-antimony alloy is treated by this process. The impurity metals were removed effectively since the leaching efficiencies of copper, nickel and antimony are over 99%, with direct recovery of gold being 99.83% that is about 20% higher than that of the original process and silver, antimony, copper and nickel are also recovered effectively. The gold grade of the resulting crude gold powder can reach to 94%.The new process has been applied in the treatment of gold-antimony alloy for two years, and many former procedures have been cancelled, such as electrolysis, Anode slime leaching by nitric acid, smelting in crucible and blowing in muffle. The new process is more shorten, lower cost and friendly to the circumstance comparing to the original process.

Jan 1, 2008

By Anja Pfennig, Thomas Böllinghaus, Marcus Wolf

During CCS components are exposed to a corrosive environment and mechanical stress which results in corrosion fatigue and is inevitably followed by the lifetime reduction of these components. The lifetime reduction of the cyclically loaded high alloyed stainless injectionpipe steel AISI 420C (X46Cr13, 1.4034) constantly exposed to highly corrosive CO2- saturated hot thermal water is demonstrated in in-situ-laboratory experiments (T = 60 °C, brine: Stuttgart Aquifer, flow rate: 30 l/h, CO2) in an environment similar to the on-shore CCS-site in the Northern German Bassin. In-situ tension-compression experiments were established simultaneously along with electrochemical measurements using a newly designed corrosion chamber in a resonant testing machine at a frequency as low as 30 – 40 Hz. In addition technical CO2 was introduced into the closed system at a rate close to 9 L/h. S-N plots, micrographic analysis and surface analysis of the fracture surface are demonstrated. X46Cr13 (surface roughness Rz = 4) reached the maximum number of cycles (12.5 x 106) at stress amplitude of 173 MPa producing a low scatter range of 1:3.5. Hydroxide and siderite layers were found on pits and crack surfaces. No typical fatigue limit exists. Pit corrosion prior to crack initiation may be identified as failure cause.

Jan 1, 2016

By Luiz A. Teixeira

A process is described whereby worn, deffective or crystallized photoconductive Se-As layers can be stripped off from aluminium photocopier drums, using hydrogen peroxide solutions in conditions such that the aluminium substrate is preserved from chemical attack. The process allows the stripped drum to be recoated with a new photoconductive layer, and to be put again in use.

Jan 1, 1990

By Tianzu Yang, Weifeng Liu, Lin Chen, Qingkai Xiao, DUCHAO ZHANG

To solve the problem of low leaching ratio of direct gold cyanide leaching from arsenical refractory gold concentrate, this paper proposed a matte smelting process for gold enrichment in low grade copper matte. The effects of copper content in the mixed material, ratio change in slag type, smelting temperature and reaction time on recovery rate of gold and copper were investigated. The experimental results indicated that the recovery rate of gold increased with the increase of copper content in the mixed materials, temperature and reaction time. It was also noted that the recovery rate of gold and copper were respectively 98.16% and 96.39% when the addition of copper content in the mixed material was 3%, slag type of CaO/SiO2 and FeO/SiO2 were 0.6 and 0.9 in 1250°C and the time of reaction was 40min. Most of the arsenic was oxidized into As2O3 existed in the dust. The results showed that the matte smelting method can achieve efficient recovery of gold from arsenical refractory gold concentrate.

Jan 1, 2016

By Lv Guozhi, Niu Liping, Liu Yan, Zhang Zhiqi, He Jicheng, Zhang Ting’an, Dou Zhihe

"CuCr alloy can be extensively used as contact materials in integrated circuit, electrodes, electric contact and high strength conductor. We proposed thermit reduction-electroslag remelting method of preparing the large scale CuCr alloy. But there are pores and oxide inclusions in CuCr alloy prepared by thermit reduction process. This paper studied mainly the effects of ratio of reactant and additive on the inclusion type and their occurrences in CuCr alloy. The slags and CuCr alloy were characterized respectively by XRD and SEM. The results show that when the additive is Na3AlF6, the slag consist of Al2O3 and Cr. When the additive is CaF2, the slag consist of Al2O3, Cr, CaF2 and CaAl4O7. The inclusions in CuCr alloy are mainly Al2O3 and pores which disperse in Cu-rich zone and Cu-Cr phase interface. When 5% CaF2 and 5% KClO3 are added, there are fewer pores and inclusions, and the more better microstructure.1 IntroduceCuCr alloy is the contact terminal material with an eximious properties[1,2], which gradually replaces CuBi alloy becoming the first choice for contact terminal material in the medium and high power vacuum switch after the 1970s. The traditional preparation methods of CuCr alloy mainly contain powder metallurgy, infiltration process and vacuum electric arc melting methods. But the above methods exist some shortcomings, such as poor product quality, high cost of production, processes complex ect[3-9]. CuCr alloy is made by the thermit reduction self-propagating method, which uses CuO, Cr2O3 and Al as raw material to get the high-temperature melt, and then casts to manufacture CuCr alloy ingot, which response equation follows as:"

Jan 1, 2012

By Larry M. Southwick, Phillip J. Mackey, A. E. (Bert) Wraith, Albert Pelletier

In 1881, the first commercial pneumatic Bessemer-type converter treating copper matte was successfully introduced by Pierre Manhes at the Eguilles copper plant near Vedène in France. This development followed over a year of testing on a smaller scale at a foundry in Vedène, during which the vertical tuyeres of the conventional Bessemer converter had been successfully replaced by horizontal tuyeres in an effort to avoid the freezing of copper which had occurred in the bottom of the vessel having vertical tuyeres. The Manhes Converter, as it became known, was the first successful large-scale adaptation of the Bessemer concept of using compressed air blown into a melt for metal refining and treatment. Within a few years, Manhes Converters utilizing horizontal tuyeres in either the original type of vertical converter, or a later and more enduring horizontal barrel converter, were in operation at over a dozen copper smelters around the world. It was this process that Messrs Peirce and Smith essentially improved with the introduction of the larger converter which bears their name and the development celebrated at this Symposium. The present paper briefly traces the original development by Pierre Manhes in the early 1880s and which set the stage for the later Peirce-Smith adaptation. The paper observes that the original development by Manhes was in part driven by the need to reduce coal (energy) consumption and hence the production cost in order for Eguilles to remain competitive with the larger plants in Swansea, Wales, where a ready supply of cheap coal helped keep smelter treatment terms of the day low. These themes are eerily resonant of today where booming copper production in China has impacted the industry, and also where energy consumption, closely linked to today’s more familiar theme of ‘climate change’ remains an important challenge currently confronting the entire industry. The paper concludes with comments on these seemingly parallel situations today and offers some thoughts for the future.

Jan 1, 2009

By Jan Dabrovska

Solidification and cooling of a continuously cast slab and simultaneous heating of a mould is a very complicated problem of transient heat and mass transfer. Nowadays, the solving of such a problem is impossible without numerical models of the temperature field not only of the slab itself, while it is being processed through the whole concasting machine (Caster), but of the mould as well. Two original numerical models have been developed and used in the investigation of a continuously cast steel slab. The first (one of two) 3D model of the temperature field of a concasting is capable of simulating the temperature field of a caster. Experimental research and data acquisition have to be conducted simultaneously with the numerical computation-not only to confront it with the actual numerical model, but also to make it more accurate throughout the process. After computation, it is possible to obtain the temperatures at each node of the network, and at each time of the process. The utilization of the numerical model of solidification and cooling of a concasting plays an indispensable role in practice. The potential change of technology-on the basis of computation-is constantly guided by the effort to optimize, i.e. to maximize the quality of the process. The user can therefore choose any appropriate longitudinal or cross-section of a slab and display or print the temperature field in a 3D or 2D graph whenever necessary. The second numerical model of dendritic segregation of elements assesses critical points of slabs from the viewpoint of their increased susceptibility to crack and fissure. In order to apply this model, it is necessary to analyze the heterogeneity of samples of the constituent elements (Mu, Si and others) and impurities (P, S and others) in characteristic places of the solidifying slab. The numerical model, based on measurement results obtained by an electron micro-probe, generates distribution curves showing the dendritic segregation of the analyzed element, together with the distribution coefficients of the elements between the liquid and solid states. The combination of both models enables the prediction of cracks and fissures in critical points of the continuously cast carbon-steel slab. Both models had been applied in the industrial investigation of a cast low-carbon-steel slab.

Jan 1, 2003

By Jonkion M. Font, Ramana G. Reddy

A thermodynamic model for a priori predictions of arsenic and antimony impurity capacity in Ni-Cu mattes and slags was developed based on the Reddy-Blander (RB) capacity model. The As and Sb capacities were calculated a-priori considering the RB capacity model in Ni-Cu mattes and FeO-FeO1.5-MgO-CuO0.5-NiO-SiO2 slag at 1573 K and 0.1 to 1 atm partial pressure of SO2. The results showed an excellent agreement between the model calculated and experimental data of arsenic and antimony capacities between the mattes and slag. The impurity capacity model developed here, can be extended for prediction of impurity capacities in multi-component base metal slags and base metal mattes. Such a priori predictions of impurity capacities can lead to develop or improve the efficiency of impurity removal from the base metal smelting, converting and refining processes.

Jan 1, 2014

By Hongbo Yang, Tongbo Zhang, Ting Huang, Jingshe Li, Fangfang Song

"Liquid core length is a very important parameter of the process of continuous casting, which directly reflects the cooling status in secondary cooling zone and solidification rate of the slab. In this paper, the billet caster in some steel plant in China was chosen as the prototype of simulating. A numerical simulating model for calculating the liquid core length of continuous casting billet was built by ProCAST software, which was verified reasonable and accurate by pin-shooting technique. Based on the model, the relationships between casting speed, casting temperature and liquid core length of casting billet were found, which was very practically useful for the workers on sit to improve casting billet quality. IntroductionContinuous casting process developed very rapidly because of the high metal yield, energy saving, and low-cost 111• And the quality requirements of continuous casting billet for customers became higher and higher with the fast development of economic121• Internal defect usually is the major quality problem for continuous casting billet[3•61 , which is influenced by the solidification process of casting billet, especially the solidification process of liquid core17•81 • So it is very important to study on the relationship between casting parameters and the liquid core length which means the distance between the crystallizer meniscus and the casting billet solidification end-point. In practical production process, the workers usually control the quality of casting billet according to the liquid core length."

Jan 1, 2013

By Mariana H. Staia

The present communication reports the results obtained by applying different concentration methods, at laboratory level, to the black sands from Estado Bolivar, Venezuela, with the aim of obtaining an adequate ilmenitic concentrate for the subsequent chlorination process. Sizing analysis was performed and plasma emission spectroscopy method was used to determine the chemical composition. It was found that from the two hydrogravimetric methods used, the Humphrey spirals is much more effective than Wilfley tables, leading to a 85% recovery. The most convenient particle size group for these concentration methods was the one corresponding to ASTM 40-140 mesh. When magnetic concentration was applied to the concentrate, obtained as a product from Humphrey spiral, a recovery of ilmenite more than 90% was obtained in the first step. It has been shown that the ore would respond to the separation techniques employed, giving individual minerals: ilmenite, zircon and silica as concentration products.

Jan 1, 1995

By Jana Dobrovska

Solidification and cooling of a continuously cast slab and simultaneous heating of a mould is a very complicated problem of transient heat and mass transfer. Nowadays, the solving of such a problem is impossible without numerical models of the temperature field not only of the slab itself, while it is being processed through the whole concasting machine (Caster), but of the mould as well. Two original numerical models have been developed and used in the investigation of a continuously cast steel slab. The first (one of two) 3D model of the temperature field of a concasting is capable of simulating the temperature field of a caster. Experimental research and data acquisition have to be conducted simultaneously with the numerical computation-not only to confront it with the actual numerical model, but also to make it more accurate throughout the process. After computation, it is possible to obtain the temperatures al each node of the network, and at each time of the process. The utilization of the numerical model of solidification and cooling of a concasting plays an indispensable role in practice. The potential change of technology-on the basis of computation-is constantly guided by the effort to optimize, i.e. to maximize the quality of the process. The user can therefore choose any appropriate longitudinal or cross-section of a slab and display or print the temperature field in a 3D or 20 graph whenever necessary. The second numerical model of dendritic segregation of elements assesses critical points of slabs from the viewpoint of their increased susceptibility to crack and fissure. In order to apply this model, it is necessary to analyze the heterogeneity of samples of the constituent elements (Mn, Si and others) and impurities (P, S and others) in characteristic places of the solidifying slab. The numerical model, based on measurement results obtained by an electron micro-probe, generates distribution curves showing the dendritic segregation of the analyzed element, together with the distribution coefficients of the elements between the liquid and solid states. The combination of both models enables the prediction of cracks and fissures in critical points of the continuously cast carbon-steel slab. Both models had been applied in the industrial investigation of a cast low-carbon-steel slab.

Jan 1, 2003

By Marietta Canty

A paper is presented in which an innovative biological process is described for the treatment of cyanide-, metals-, and nitrate-contaminated mine process water. The technology was tested for its ability to detoxify cyanide and nitrate and immobilize metals in wastewater from agitation cyanide leaching. A pilot-scale demonstration is described in which a pilot plant was constructed to demonstrate the technology on a mine process waste stream at a mine in Nevada. The demonstration was performed Jointly under the Mine Waste Technology Program (MWTP), which is funded by the U.S. Environmental Protection Agency (EPA) and is jointly administered by the U.S. Department of Energy's (DOE) Western Environmental Technology Office (WETO) and the Superfund Innovative Technology Evaluation (SITE) Demonstration Program under Interagency Agreement Number DW89938513-0 I-0. MSE Technology Applications, Inc. (MSE) located in Butte. Montana, was the contractor responsible for conducting the project, and Pintail Systems, Inc., of Aurora. Colorado, was the technology provider. The pilot-scale unit was field-tested at the Echo Bay McCoy/Cove Mine southwest of Battle Mountain, Nevada. The biotreatment process was considered to be successful in destroying cyanide in the mine process water. The process was also determined to be effective in removing metals. The pH was consistently neutralized, and nitrates were successfully removed from the mine process water. As a result of conducting these pilot-scale tests, the biotreatment process was concluded to be an innovative, cost-effective alternative for the treatment of mining wastewaters.

Jan 1, 1998