Search Documents

By Xianming Zhou

Mining economics is such that too conservative in safety will result in a considerable penalty in mining cost. However, initial planning and design of a mining project often must be done without complete information. The assurance of economical and safe mining is thus difficult. This study is focused on the improvement of the mine design associated with Zhaoyuan Gold Mine in P.R. China as more information becomes available. Attention is given to the selection of backfill structures. Based on a proposed practical finite element model, a design, which is believed to be not only reliable but also cost-effective, is recommended for further mining operations in this mine.

Jan 1, 1989

Effective strata control, utilising fully encapsulated roof bolts, is dependent on the installed quality of the reinforcement elements. One mechanism by which fully encapsulated roof bolts may become less than fully effective is by gloving (glove fingering) and un-mixing of the resin. Following some small roof failures containing gloved bolts, investigations have been undertaken in some New Zealand coal mines to determine the extent of, and mechanisms involved in, the gloving of fully encapsulated roof bolts for a range of roof types and installation methods. Gloving, in this context, refers to the resin cartridge partially or completely enveloping a length of the bolt, typically with unmixed resin filler and catalyst/hardener remaining within the cartridge. Results have shown that gloving and un-mixing is a systematic and widespread phenomena, occurring across a range of resin and/or bolt manufacturers, and across a variety of roof types. Gloving was found in bolts installed using: hand held pneumatic and continuous miner mounted hydraulic methods, under run of mine (ROM) conditions by mine workers, and under controlled "best practice" conditions. The roofs bolts investigated are all 1800mm (6ft) long, and have shown that, on average, 485mm (-19") of the bolt length is gloved and/or unmixed. This equates to a 27 percent reduction in effective bolt length. The effected length of bolt is sufficient to impact on the load transfer/reinforcement capabilities of the bolt system, and hence impacts on the design assumptions and subsequent stability assessments. Furthermore, there is a direct relationship between the mechanism for the gloving of bolts and an increased occurrence of resin loss and reduction in encapsulations length in soft (less than 10 MPa) and/or highly fractured rock. Investigations have concentrated on developing an understanding of the mechanisms involved. This has been undertaken using both field installations and recovered bolts, as well as test bench trials. The mechanisms involved have been confirmed as being: the development of a pressure front as the bolt encounters the resin and is spun up the hole, which, in turn, leads to over-pressurisation and radial expansion of the resin cartridge, resulting in an increase in diameter of the plastic resin cartridge, which allows the bolt to be spun up into the cartridge without making sufficient contact to shred the cartridge or the hardener tube, resulting in an unmixed portion of resin.

Jan 1, 2003

By Y. P. Chugh

About 60-70% of the underground mined coal in Illinois is extracted using a room-and-pillar mining method that permits extraction of about 50% of the coal. The remaining coal is left behind in the form of support pillars to control surface and subsurface movements. Illinois coal seams are typically associated with water sensitive weak floor strata whose thickness varies 0.31 - 1.3 m. The current mining geometry mostly uses pillars of constant size within a mining area. This traditional practice suffers from the disadvantage that pillars within the center region are subject to much higher loads than the pillars located on the outer edges of the panel. This results in a higher incidence of rib spalling, and roof falls, creating a potentially hazardous work environment. In addition, this concentration of loading at the center of the panel provides initiation points for floor failure to occur. The primary goal of this study was to reduce ground control problems and production costs in Illinois mines by considering alternate mining geometries. The development and subsequent field demonstration of an alternate geometry is presented in this paper.

Jan 1, 2004

By G. Skybey

The Directional Drill Monitor (DDM) is an advanced instrument for real time in hole surveying. It was developed by Du Pont (Australia) to suit Australian gassy coal mining conditions. The instrument consists of three units: i. Down hole transmitter ii. Acoustic transducer iii. Data receiver processor unit (i.e. up hole unit). This paper describes the function of each unit in detail and highlights the importance of the DDM in long hole drilling efficiency. Surveying is carried out independent of hole depth. Each survey takes 2-3 minutes to complete, the frequency of surveying to control borehole trajectory is determined by the accuracy required for a particular hole. The DDM is currently being used successfully for long hole drilling in a number of collieries. A high degree of directional control has been achieved. Borehole trajectories were controlled to within +l¬2m of the planned path with intersurvey distances varying between 6 to 18 metres over distances up to 700 metres.

Jan 1, 1992

By Vladimir Adamek

Two existing predictive methods were chosen for evaluation; an influence function (Gals Theory) and a profile function (hyperbolic). These were applied to several field measured subsidence pro¬files over United States coal mines. The effect of homogeneous versus non-homogeneous overburden on surface subsidence is demonstrated and the utilization of Bals Theory as a subsidence predictive method for both types of overburden is examined. The major factor affecting subsidence profile characteristics is the migration of the inflection point toward the centerline of the longwall panel. A computer program was written to aid in the analysis.

Jan 1, 1981

By Rodger Fry

All coal deposits contain anomalous geologic conditions which have an impact on roof control, Run-Of--Mine (ROM) coal quality and production costs. To remain competitive in today's coal market and provide a safe working atmosphere, mine operators need to know in advance of mining the geologic conditions which prevail in the coal deposit. In order to identify geologic anomalies within a coal seam and surrounding roof rock in advance of mining, the Radio Imaging Method (RIM) survey procedure has been developed. This paper describes the RIM procedure and how it is used to predict various geologic conditions within a coal deposit. Figure 1 illustrates the RIM in-mine and surface surveys which can be used in an underground mine. [ ] RIM is an electromagnetic (EM} wave process which consists of in-mine and surface survey techniques. Both techniques are used in underground coal mines to detect faults, interbedding, sandstone channels, and thinning coal. Thesurface survey can also be used to determine seam correlation and continuity in strip and underground mining. In-mine and surface surveys work by propagating EM waves along straight paths through the coal. As the RIM signal travels along a ray path, it interacts with the seam material and surrounding rock. This interaction causes the signal to lose energy thereby decreasing its strength along the path. The amount of energy loss per unit path length depends upon the coal seam height and type of surrounding roof and floor rock. A reading of the signal level is taken at the end of the ray path at the receiver location. This reading is used to determine the loss (attenuation) rate of the signal along the path. The signal level data is compiled and analyzed through computerized algorithms which construct images of any anomaly present. This graphical depiction of the coal provides a basis for further geologic interpretation. By comparing the images reconstructed by the RIM analysis to in-mine geologic mappings made while mining through RIM study zones, it has been confirmed that RIM can help detect the following; Rapidly Thinning Coal Incompetent Roof Rock Poor Floor Lithology

Jan 1, 1984

By Rene Rodriguez

The initial results of our investigations on the applicability of geophysical exploration methods to map coal seam inclusions were summarized in a paper submitted at the Thirteenth Conference on Ground Control in Mining in 1994. These investigations were continued under a variety of conditions at a number of underground coal mining operations. The results have been encouraging and have fostered a much more detailed understanding of the geophysical principles at work in underground mine mapping. This report summarizes a particularly interesting application, that is, the use of Underground In-Seam Seismic exploration methods to identify and to approximately delineate coal seam inclusions within longwall panels. The methodology relies on the excitation of seismic sources in the coal seam along one side of the panel and the recording of seismic waves by geophones secured to the coal rib on the opposite side. Head-Body waves (compressional and shear), direct and channel waves are generated in the process. While the head waves are critically refracted waves traveling at the coal floor and roof, direct and channel waves are transmitted through the coal body and are dispersive in character. Tomographic techniques applied to the velocity inversion of first arrivals permits a fast mapping of coal seam inclusions in the panel. The process incorporates path velocity and geostatistical intersect analysis. Full wave analysis of the dispersive channel waves, provides an independent and confirmatory information of the coal geometry, including the inclusions within. The inversion technique in this case is the modal analysis of the wave trains. The application of this method to three different problems was confirmed by subsequent mining of the predicted anomalies, proving the accuracy of the technique within limits of experimental error.

Jan 1, 1995

By John L. Hill

Cutter roof failure is a specific type of ground control problem which frequently results in massive roof failure. It is a cannon occurrence in coal mines of the Northern Appalachian Coal Sasin, causing delays in production and posing a safety hazard to mine personnel. The Bureau of Mines is conducting research on the causes of cutter roof failure togain a basis from which to prevent its occurrence and to support such roof when failure does occur. Research conducted in a coal mine of central Pennsylvania has revealed a correlation between the occurrence of clastic dikes and fonation of cutter roof failure. Inmine mapping of ground conditions showed an increase in roof failure in areas of high frequencies of clastic dikes. Rock pressure monitoring around clastic dires registered the greatest amount of roof loading near the inter- section of dikes with the rib. Load cells measurim horizontal pressure changes in the roof indicated that the greitest pressure changes were occurring perpendicular to entry headings when clastic dikes were present. Analysts of rock pressure nwnitiring shows that the roof behaved as two cantilever beams when severed by a clastic dike. Additional roof supports such as trusses and cribbing were found to effectfvelv suooort the roof in areas of clastic dikes and prevent cutter roof iailure. However, there lnethads were only successful when employed shortly after mining.

Jan 1, 1984

By Asmaa Yassien

Finite element models were developed to study the effect of tensioned and fully-grouted bolts on the stability of the mine opening in a three-entry development system using a typical geological column for the Pittsburgh Coal Seam. The models were used to study the effect of each bolt type on the stress distribution in the immediate roof, yield zone development and the vertical deformations. Comparison of all of those features show that the effect of a tensioned bolt on the stress distribution in the immediate roof is restricted to limited areas, whereas the fully-grouted bolt has a much wider effect on the stress distribution. Both types of bolts can reduce the yielding and deformation in the immediate roof to different degrees. The fully-grouted bolt reduces the sliding along the bedding plane more than the tensioned bolt. Both types of bolts were able to maintain the bedding planes without separation. The induced forces in both types of bolts are analyzed. A rapid increase in the shear force and bending moment occurred in the fully¬grouted bolt due to the relative motion of bedding planes.

Jan 1, 2002

By David Gearhart, Peter Zhang, Gabriel Esterhuizen

"Researchers from the National Institute for Safety and Health (NIOSH) installed instruments in the track entry and in the pillars of a northern West Virginia longwall coal mine between two planned panels for the purpose of monitoring the behavior of the ground. The instruments included four cable bolt load cells to measure the change in gateroad loading, six borehole pressure cells to measure the loading in the pillars, three six-channel roof extensometers to measure roof sag, four convergence measurements on the cribs to measure the crib loading, and a multipoint borehole extensometer to measure the pillar expansion. The instrumentation was all connected through two multiplexers to a single Campbell Scientific permissible datalogger located about 350 feet outby the instruments. The goal of the project was to record all of the measurements as both longwall faces passed the site of the instrumentation and to use the data to calibrate numerical models.This report describes the recording of all of the measurements taken as the first panel approached and then passed the instrumentation site. This study provided valuable data related to the ground response and support performance that will be used to improve safety in longwall gateroads.INTRODUCTIONA longwall mine in northern West Virginia was selected as a second study site for an ongoing research project into gateroad layout and support design. The area was affected by a transition from limestone to sandstone in the roof. The entries were 16 feet wide, and the height was approximately 80 inches. The layout for the longwall panels was 1,170 feet wide by 4,000 feet long. The panel configuration was right-handed, and a three-entry gateroad was used between panels. The pillars next to the headgate were 137.5 feet by 115 feet center-to-center, and the pillars next to the tailgate were 275 feet by 100 feet center-to-center, with the crosscuts at 60 degrees. The width of the gateroad was a total of 215 feet."

Jan 1, 2018

By Axel Preusse

This paper shows basic considerations about the prognosis and prediction of surface subsidence and other ground movements in the German hardcoal industry. The following case studies describe experiences collected in projects between university and industry.

Jan 1, 2000

By Anthony T. Iannachione

The location and time of 2,007 microseismic emissions from a limestone mine in southwestern Pennsylvania were compared with the development of mine faces and the characteristics of the mine layout. Based on analyses of these results, the occurrence of roof failure zones appears to be associated with certain characteristics of the mine plan. It was determined that significant relationships exist between the intensity of the microseismic activity and the scale of the roof failures. Microseismic activity associated with these roof falls occurs in distinct episodes, with the final failure event occurring during approximately a 12-hour period. Each roof fall episode appears to be composed of dozens of distinct roof beam failures. As each beam fails in shear and tension, tens to hundreds of audible noises representing rock fracturing or bedding plane separation can occur. While every roof fall can be viewed as unique, certain mechanistic similarities can be realized through careful observation and monitoring of these complex systems. Understanding these similarities in characteristics allows mine personnel to design the most effective and efficient control technique.

Jan 1, 2001

By Gift Makusha

Surface subsidence associated with coal mining activities in the Mpumalanga Province of South Africa changes the natural environment in several ways, and current challenges for mining companies include rehabilitation of the natural environment and the prevention of further degradation. To monitor the spatial and temporal evolution of surface subsidence, traditional fieldbased monitoring approaches such as GPS and spirit leveling are employed at a number of locations. However, the resulting measurements are point-based, and frequent revisitations are necessary to map the evolution of surface subsidence basins over time. To address these limitations, differential interferograms derived from repeat-pass satellite-borne synthetic aperture radar (SAR) systems were tested for their ability to measure and monitor surface deformation. The SAR data was captured by the European ERS-1 and ERS-2 satellite and covered a timeframe between 2008- 09-15 and 2008-09-15. The resulting interferograms revealed several features indicative of surface subsidence. Ground truth data confirmed the presence of a subsidence basin, detected using differential interferometry techniques during the 35-day period between April 12, 2008 and May 17, 2008; a maximum vertical deformation of 3.2 cm (1.3 in) was recorded. Interferometric monitoring revealed an eastward migration of the subsidence basin between June 2, 2008 and September 15, 2008 with an additional 4.7 cm (1.9 in) of subsidence observed. This migration coincides with the advance of the working face of the mine during this period. Finite element modeling will be performed in order to model the rates and evolution of surface subsidence haloes as underground mining advances. These presented results demonstrate the ability of interferometric synthetic aperture radar techniques to measure surface subsidence as well as the monitoring of the evolution of subsidence basins over time. This implies that the technique could be included, together with traditional field-based surveying techniques, in an operational monitoring system. With knowledge on deformation rates and subsidence basin evolution, informed decisions on current and future infrastructure development can be made and remedial actions and prevention strategies can be formulated for the problems associated with environmental degradation.

Jan 1, 2011

By Thomas Barczak

Longwall mines typically use some form of standing support for secondary roof support in longwall tailgate entries. Although there have been several new support products developed for this application, there remains no universal design criteria to optimize the application of these support technologies. The requirement for optimization and proper support selection is to understand the degree of control that the support has on the ground behavior. The ground reaction curve and numerical modeling was used to evaluate the impact of standing support on ground behavior. LaModel was used to evaluate the impact of standing support on main roof and floor behavior and pillar yielding. The conclusion drawn from this study was that standing supports do not have sufficient capacity to control main roof or floor loading or prevent the resulting convergence of the tailgate entry. However, it is imperative that this "uncontrollable convergence" be considered in the support design to prevent premature failure of the support. A FLAC model was used to evaluate the near-seam roof and floor behavior in conjunction with the global vertical and horizontal stresses. The model suggests that standing roof supports can have some impact on the ground behavior as the elastic response of the rock is exceeded and rock structure deteriorates from the stress concentrations that develop around the tailgate opening. During this phase, the capacity and stiffhess of the standing support can be critical to the stability of the opening, as eventually the rock mass will be transformed into a partially detached structure whose weight must be supported by the standing support. This work is part of a ground control program of research at the National Institute for Occupational Safety and Health (NIOSH) aimed at improving mine safety by reducing roof fall injuries and fatalities.

Jan 1, 2005

By Peter Cain

In 1993 an opportunity presented to monitor the effects of undermining an abandoned roadway by a longwall panel in the Sydney. N.S. coal field. Interaction subsidence data was collected by survey leveling to benchmarks in the undermined gateroad as well as by a standpipe system equipped with 15 vibrating wire piezometers measuring changes in elevation in the gateroad relative to an outby header tank. The piezometers were monitored at 30 minute intervals using a datalogger. while the leveling surveys were conducted weekly over the life of the project. The monitoring program resulted in the collection of a very large both of data. relating vertical subsidence to the relative position of the underlying face. The most basic analyses derived a travelling subsidence curve from the leveling data only. which hinted at a relationship between rate of extraction in the panel below and the amount of strain developed in the undermined strata. The complexity of the relationships between the amount of subsidence obtained, the location of' the individual monitoring stations, the rate of face advance below and the potential for "periodic" subsidence due to geological conditions has made analysis difficult. and the amount of data has compounded this problem. Recently. an analytical approach using a commercial neural network analysis package has been applied. which appears to have resulted in the ability to draw sonic meaningful conclusions from the data set. In this paper a short history regarding the collection of the data set is followed by a brief' description of neural networks. This is followed by a description of the several analyses performed. some of the results obtained, and conclusions drawn.

Jan 1, 1998

By Peter Hayes

Moonee Colliery operates a longwall extraction system in the Great Northern seam of the Newcastle Coal Measures, approximately 100km north of Sydney, NSW. In the initial mine area of longwall blocks1-4a, the Great Northern seam is overlain by a massive conglomerate approximately 35m in thickness. Unanticipated sudden, blocky caving of this material has produced windblasts with associated velocities of 100m/sec and over-pressures of 35kPa. Although these events have not resulted in fatality, the potential safety risk to face personnel was such that the mine was threatened with closure. The development of a Windblast Management Plan to minimise the exposure to windblasts, a Micro-seismic Management flan to predict caving events, and the use of hydraulic fracturing to generate caving on demand, have all contributed to the salvation of the mine. Prior to the introduction of hydraulic fracturing, falls were highly variable and ranged in goaf area from 2000m2 to 30,000m2 with an average of around 7.000m2. Hydraulic fracturing has introduced consistent and far less variable falls, planned as averaging around 5000m2 and all accompanied by microseismic warning, Moonee Colliery is believed to he the only operation in the world using real-time microseismic warning and using hydrofracturing as a day-to-day operational process. These processes have enabled it to return to financial viability in an environment of strict procedural control, whilst ongoing efforts are made to optimise and enhance these systems. Moonee's story is a case study of the successful application of research and development work to the economics of a mine.

Jan 1, 2000

By Paul Cartwright

A rockbolted roadway risk assessment procedure has been developed specifically for the Parkgate seam at Thoresby Colliery by Rock Mechanics Technology and colliery engineers. The purpose of this assessment is to identify any areas of significant risk in relation to roof instability due to potential failure or overloading of the rockbolt support system. This allows appropriate additional support to be installed in sections of roadway considered to be at increased risk. The assessment of risk in rockbolted coal mine roadways, in terms of fall of material, has to be based on an understanding of the rock mass behaviour at that site. The development of an appropriate risk assessment system is therefore site specific. A consistent approach to developing such a system can, however, be applied by adopting the same general logic to each individual site. The use of risk assessment to categorise areas with increased risk of roof instability has been undertaken for four longwall panels at Thoresby. The procedures used for these assessments are discussed and the operational benefits examined. The approach successfully used at Thoresby has been developed into a routine tool to assist mine personnel in assessing areas of potential roof instability in rockbolted roadways and as a means of communicating the position of these areas to both supervisors and workmen. The system provides a rational and objective interpretation of the current underground conditions based upon a logical, consistent and structured approach.

Jan 1, 1999

By Russell Frith

Probably the most expensive but least well understood roof falls in underground coal mining, are those that occur ahead of the powered supports in the centre of longwall face. Even small roof cavities result in the dilution of the ROM product and large cavities can stop the face for days if not weeks and the incurred cash flow losses can be catastrophic. Expensive and time-consuming remedial measures (e.g. PUR, cavity filling, removal of stone from the AFC by hand) are required and equipment wear and damage can be significant when the need to blast and convey stone is also considered. Through four major research projects within the Australian coal industry and numerous consulting assignments, the author has spent the best part of fifteen years attempting to identify and defme the various geotechnical and operational factors that determine whether a major roof cavity occurs ahead of the powered supports or a normal goaf fall occurs just behind them, the difference in operational outcome being enormous. The paper presents a condensed summary of the overall technical findings covering such issues as roof fall mechanisms, the measured influence of cover depth, periodic weighting of massive strata units and its quantification, the role of cut-throughs in chain pillars, face width and height, the role of the powered support and the influence (both positive and negative) of mine site operations. The big picture outcome is the view that high production longwall extraction is well-suited to certain geotechnical environments, is marginal in others and under certain conditions is fatally flawed and beyond the control of mine operators, although fortunately the latter category is a relatively rare situation. Various risk-based research findings in this regard will be given as a basis for future discussion.

Jan 1, 2005

By E. H. R. Schumann

The local stratigraphy and composition of the coal measures, including competent dolerite sill and massive sandstone lavers is shown to have a restricting influence on the development and magnitude of surface subsidence above total extraction panels in South Africa. The critical panel width necessary to induce nonviolent failure of a dolerite sill is quantified. Small subsidence due to the deflection of a 70 metre thick dolerite above subcritical panels is shown by example. Maximum surface subsidence tilt an; ground strain is compared to the NCB model. An exponential subsidence profile curve, SPC, describes a trough half-profile. A parabolic relationship between horizontal displacement and tilt, which has been discovered to exist can be substituted in the first derivative of the SPC in order to generate transverse displacement and strain profiles.

Jan 1, 1988

By Bret E. Leisemann

The geomechanical environment in which highwall mining must operate represents a hybrid between surface and underground operations. Mine design must take into consideration the complexities associated with unsupported spans, pillars with extreme aspect ratios and the instability related to the interaction between coal extraction and the highwall stability. The rock mass adjacent to the highwall, and for a significant distance in, is affected by lateral stress relief and blast damage. This paper describes a rigorous site investigation program aimed at providing some of the input parameters for the design of highwall mining layouts at the Moura Mine and focuses upon defining the nature and extent of the relaxed zone behind the highwall. The combination of borehole imaging and C factor analysis allows delineation of blast damage and relaxation of the rock mass immediately adjacent to the highwall excavation, as well as the more subtle relaxation effects deeper into the rock mass. This has led to the formulation of a proposed geomechanical model for the relaxed zone for direct input into highwall instability analysis and mine design.

Jan 1, 1993