Search Documents

By William Blake

Mining induced rock bursts have been a severe operational hazard associated with the deep silver mines of the Coeur d'Alene mining district for over 30 years. Recent studies during the past fm years have led to a better understanding of the different types of rook bursts and their causative mechanisms. This has resulted in ground control measures that more effectively minimize burst occurrences as well as contain burst damage. Case histories of burst incidences and examples of control measures are presented.

Jan 1, 1987

By Meng Xiao, Peng Huang, Lizin Lan, Feng Ju, Shuai Guo

"Through changing the axial load on backfilling material compaction test to reflect different overlying strata pressure on backfilling material, the stress-strain relations in the compaction process of backfilling material under the geological condition can be obtained. Based on the characteristic of overlying strata movement in backfill mining, a model of roof thin plate is established. By introducing the stress-strain relation in compaction process into the model and using RIZT method to analyze the bending deformation of roof, the bending deflection and stress distribution can be obtained. The results show that the maximum roof subsidence and maximum tensile stress occurring at the center are 255mm and 5 MPa, respectively. Tensile fracture of roof under the geological condition of Dongping mine did not occur. The dynamic measurement results of roof in Dongping mine verify the theoretical result from the aforementioned model, thereby suggesting the roof mechanical model is reliable. The roof thin plate model based on the compaction characteristic of backfilling material in this study is of importance to research on backfill mining theories and application of backfilling material characteristics.INTRODUCTIONSolid backfilling mining (SBM) is a green mining technology in which the solid waste materials is placed into the gob to support the overlying strata and to control roof's subsidence and movement (Miao, 2012; Miao et al., 2010, 2015). SBM has been successfully used in several mines to solve many problems, including coal extraction under buildings, water bodies and railways, surface subsidence, and environmental problems. Good results have been obtained in many mines (Zhang et al., 2009). The key in the application of SBM technology is controlling strata movement. However, the critical factor influencing the controlling effect of strata movement is compaction characteristics of backfilling materials. Thus, a roof model of SBM is built based on the filling materials' compaction characteristics. A subsidence equation and the critical failure condition of roof was given and field verification was performed at Panel 15061 of Donping Mine."

Jan 1, 2016

By Kristine L. Pankow, Keith D. Koper, Michael K. McCarter, Jared R. Stein

"The Wasatch Plateau region of central Utah contains a number of active underground coal mines in an area of well-documented natural seismicity. As a result, there are several hundred seismic events recorded in this region every year that may or may not be attributed directly to mining activity. Previous studies have linked the majority of this seismicity to mining activity through various means, but have not attempted to develop a method for categorizing individual events within a seismicity catalog. This study uses both relative relocation and waveform cross-correlation to separate events based on hypocentral depth and waveform similarity, respectively, in the area surrounding a single longwall coal mine within the Wasatch Plateau. We conclude that relative relocation can help with depth discrimination, but there are some unavoidable limitations caused by sparse seismic network coverage. The cross-correlation technique is more promising, with the ability to group events by waveform similarity and track mining progress over both space and time. With cross-correlation based clustering, we confirm that the vast majority (97.6%) of events in the study area are directly related to mining activity, but that a small population of natural seismicity is present as well. Eliminating this natural seismicity from the catalog of seismic events, leaving only those events related to mining, can give operators valuable information about the changing conditions as mining progresses and eliminate concern over events unrelated to mining activity.INTRODUCTIONA number of underground coal mines are located in the Wasatch Plateau region of central Utah, and have been in operation since the late 1800s. This activity has resulted in a well-known history of mining induced seismicity (MIS) (Wong, 1985). Additionally, this area is situated near the border of the Basin and Range and Colorado Plateau physiographic provinces, where naturally occurring tectonic earthquakes also occur (Arabasz et al, 1980). Seismicity separating these physiographic provinces is part of a larger band of seismic activity known as the Intermountain Seismic Belt (ISB) that runs from Montana to Arizona and cuts through the western boundary of the central Utah coalfields (Smith and Arabasz, 1991) (Figure 1)."

Jan 1, 2015

By Morgan M. Sears, Gamal Rashed, Jim Winfield, Brent Slaker

"Over the past decade, ground falls have resulted in five fatalities, representing over 40% of all fatalities occurring in underground stone mines in the United States. In conjunction with recent high-profile pillar collapses, the need for further ground control research in the nation’s stone mines is evident. Ground conditions are growing more difficult. Therefore, this research is focused on deep cover, steeply dipping, and multi-level underground nonmetal mines. The objective of this paper is to introduce a geomechanical study of pillar development in a steeply dipping limestone deposit. To accomplish this, a numerical model was developed using input from modified laboratory test data and in situ stress measurements provided by the mine to simulate the development of a pillar under these conditions. The model was then verified against field observations and stress mapping. The calibrated model was then used to calculate the estimated stresses in the pillar and immediate roof as development progresses around an instrumented pillar.INTRODUCTIONGround falls represent a significant hazard in the nation’s underground stone mines. In response to recent large-scale pillar collapses, as well as stakeholder interactions, researchers from the National Institute for Occupational Safety and Health (NIOSH) are currently conducting detailed investigations into the complex loading conditions at mines operating in challenging operational environments. These include deep-cover, steeply dipping, and multi-level mines where there is the potential for an increased risk of ground failure. The Pleasant Gap Mine, shown in Figure 1, operates in the Valentine Formation, which is typically light grey, extremely fine-grained limestone, and approximately 21.3 m (70 ft.) thick. The Centre Hall Formation makes up the immediate and main roof members and is approximately 9.1 m (30 ft.) thick, consisting of medium-dark-gray limestone (Murphy et al., 2018). Situated in a syncline, the top of the Valentine Formation dips at approximately 19° with a strike of approximately N54E in the area of interest (see Figure 2)."

Jan 1, 2018

By Eric Keller, Jamal Rostami, Wenpeng Liu

"Roof and rib instability is an important issue in underground mining. To optimize ground support design, enhance ground stability, and reduce the possibility of roof or rib failure with minimal use of artificial ground support, it is essential to have an accurate understanding of ground conditions. This includes the location of voids, cracks, and discontinuities, as well as information about the different strata in the immediate roof. This paper briefly introduces ongoing research on void detection by using the roof bolter feed and rotation pressure. The goal of this project is to improve the sensitivity of detection programs to locate smaller joints and reduce the number of false alarms. This paper has presented a brief review of the testing procedures, data analysis, logic, and algorithms used for void detection. In addition, this paper has discussed the results of preliminary laboratory tests and statistical analysis of the data from these two drilling parameters used for void detection.INTRODUCTIONRoof falls are one of the most serious and frequent accidents in underground mining. Each year, personnel are injured or killed because of roof falls. Equipment can also be damaged when this occurs. According to Mine Safety and Health Administration statistics collected from 1999 to 2008, ground falls were the largest cause of fatal accidents in underground coal mining, causing around 40% of all fatalities (NIOSH, 2015a). Out of 8 to 10 fatalities and over 800 injuries are recorded each year in underground mines, there are nearly 2,000 reportable non-injury ground falls every year (NIOSH, 2015b).Certain features in the ground, such as voids, cracks, and discontinuities, are significant factors that cause roof support failures and roof fall accidents. Currently, several manufacturers provide smart roof bolters with limited capabilities for void detection. While successful in many instances, in laboratory experiments, the existing void detection systems have limited success in detecting void openings that are less than 1/8 inch This limited success was observed in testing concrete blocks with gaps in between, simulating a rock medium with voids. Detection programs have missed some voids, while, in some cases, they have shown false detection. These algorithms need to be more accurate in sensing voids to improve the capabilities of these programs."

Jan 1, 2016

By James D. Pile

Following a methane ignition in the active panel of a longwall coal mine, the affected panel was successfully isolated from the rest of the mine. This allowed for the remainder of the mine to return to regular operation, and the conventional practice of having to seal the portals for a defined period of time was avoided. After the affected panel had remained isolated for a regulatorily mandated period of time, it was reopened in preparation for longwall face recovery. As it was not possible to move the shields from their existing positions to facilitate the installation of recovery mesh prior to shield recovery, alternative methods had to be considered to stabilise the gob and minimise flushing, thereby improving operator safety. The objective of the paper is to show how stabilisation of the gob was achieved during shield recovery, thereby minimising flushing, and improving operator safety. Phenolic foam was chosen and injected from between the shields into the gob behind them. This is a technique that has been used to great effect in Germany, to a lesser extent in Australia, but not knowingly to date in the United States. To ensure nothing was left to chance and thereby guarantee the project?s success, the procedure used in Germany was employed, down to the application of equivalent hardware, which was sourced through the North American supplier.

Jan 1, 2013

By Daniel W. Su

This paper presents the implementation and evaluation of the hydraulic fracturing technique and Longwall Visual Analysis (LVA) software to mitigate the impact of a 1,000-ft (305-meter) widemassive sandstone channel on a 1,500-ft-wide (457-m-wide) longwall face. Based on a underground roof geology reconnaissance program, four frac holes were drilled and fraced along the center axis of the sandstone channel. To further provide detailed monitoring of the longwall face, the Longwall Visual Analysis (LVA) software was installed to track the face pressure and cavity formation index. In mid-December 2011, the longwall face approached and entered into the western edge of the sandstone channel. The longwall face mined through the center axis of the sandstone channel in mid-January 2012 and advanced outby the eastern edge of the sandstone channel in early February 2012. Results from daily underground observations and production delay analysis confirmed the effectiveness of the hydraulic fracturing program and the validity of the LVA Software.

Jan 1, 2012

By Andre Cezar Zingano

"The empirical approach for pillar design assumes that geological conditions should be perfect, such as horizontal seams, and that pillar strength and behavior will only depend on the coal seam strength and the vertical pressure caused by the overburden thickness on the coal seam; this vertical pressure is based on the tributary area. Empirical methods do not consider the effect of the interface between the roof and pillar or the floor and pillar.The effect of the interface shear strength on final coal pillar strength has been studied since the 1960s. However, few case studies have been generated from that, especially in shallow underground coal mining (less than 100 meters). This case study involves a mining section at the 101 coal mine in the Santa Catarina state of Brazil, which is experiencing pillar rib spalling and yielding because of a 1-to 2-cm-thick clay layer at the area of contact between the coal seam and immediate roof. The depth of the coal seam is 60 m on average and 2.3 m in height. This particular section also has 12-14% (7-8°) of seam inclination. The pillar size varies from l lxll to 13xl2m; thus, the safety factor (SF) based on the ARMPS approach is more than 1.5. The objective of this paper is to determine the cause of the pillar yielding and study the effect of the clay layer at the interface between the roof and pillar, including the inclination of the coal seam. This study conducted empirical and numerical models (2D and 3D) to understand the effect of the thin clay layer. The conclusion is that the clay layer affected the strength of the interface between roof and pillar, causing rib spalling and reducing the pillar strength.INTRODUCTIONPillar stability and deformation depends on the coal seam strength and vertical pressure caused by the overburden thickness on the coal seam, and this vertical pressure is based on the tributary area. The effect of the interface shear strength on the final coal pillar strength has been studied since the 1960s. However, few case studies have been generated from that, especially in shallow underground coal mining (less than 100 m). This interface could be represented by a thin clay layer or an abrupt contact between the coal seam and a rigid sandstone layer of the immediate roof. These two interface conditions are found in the coal mines of Brazil, and the effect of the interface shear strength could increase when the seam's inclination is higher."

Jan 1, 2016

By David F. Gearhart, Khaled M. Mohamed

"Trusses are primarily used as passive roof supports in coal mines. They are constructed of three main parts: two grouted bolts installed at opposing forty-five degree angles into the roof so that they are anchored over the ribs and a cross member that ties the angled bolts together. There is also hardware used to assemble these components. The capacities of the angled bolts are typically 30 to 40 tons and the tensile capacity of the cross member is also 30 to 40 tons. Importantly, the direction of the immediate roof loading on the cross member is unlike the direction of the loading on the angled bolts. The load on the cross member is transverse to the longitudinal axis instead of along it, and therefore the cross member is loaded in the weakest direction.Previous tests conducted on truss systems applied loads such that the increasing tension in the two diagonal bolts increased the tension in the horizontal cross member, resulting in a stiff response. By contrast, if the load is applied directly to the cross member, which then transmits those forces to the diagonal bolts, it results in a much softer response.Based on this difference, laboratory tests to apply transverse loads and measure the vertical load capacity of three different types of cross members were conducted using the Mine Roof Simulator (MRS) located at the National Institute for Occupational Safety and Health (NIOSH) in Pittsburgh. The length of the samples was about 16 feet. Single-point load tests, with the load applied in the center of the specimen were conducted to verify the performance of the test arrangement and the finite element models. Double-point load tests, with a span of eight feet, were also conducted. This arrangement replicates the performance of the cross members with a distributed load. Both of these test arrangements were conducted on one-inch-diameter threaded steel bars and 0.7-inch-diameter cable and 0.6-inch-diameter cable cross members.For the single-point load configuration, the yield of the one-inch bar was nominally 22 kips of vertical load, achieved at 17 inches of deflection. For both sizes of the cable cross members, yield was not achieved even after 18 inches of deflection. Peak vertical loads were about 20 kips for the 0.7-inch cables and 15 kips for the 0.6- inch cables. For the double-point load configurations, the one-inch bar cross members yielded at 33 kips of vertical load and 10 inches of deflection. The 0.7-inch-diameter cable cross members broke strands at 30 kips of vertical load and 10 inches of closure, and the 0.6-inch-diameter cable cross members broke strands at 25 kips of vertical load and 10 inches of closure. Finite element models of each of the six different configurations were developed and show the variation of the vertical capacity of the cross members and the difference of the behavior of the bar versus the cables."

Jan 1, 2015

By Donovan J. Benton

Photogrammetric methods are advancing rapidly and show considerable promise as a ground control research tool. The ability to quickly capture three-dimensional geometry, especially changes in geometry, in underground and laboratory settings is a significant advance from point distance measurements. Photogrammetry is being applied in both of these settings as part of the NIOSH ground control research. This paper describes these applications and the equipment and software being employed. It also describes tests conducted to quantify the accuracy of these systems. Accuracy varied with system specifics and procedures. A factory-calibrated camera produced results within 1/32 of an inch, plus 0.04%. A user-calibrated camera was found to be less accurate, at 1/20 of an inch, plus 0.24%. These calibrations demonstrate that photo grammetry can produce research quality measurements in laboratory and mine settings.

Jan 1, 2014

By Eric C. Poeck, Ryan Garvey, Ugur Ozbay, Kun Zhang

"A coal bump is characterized by the sudden failure of one or more pillars and an associated release of kinetic energy. Although the geologic conditions surrounding coal bumps are often similar, their occurrence and magnitude are difficult to predict. This paper presents the development of an approach to assess the potential for coal bumps in room and pillar mines through the use of energy concepts and special consideration of the interface properties between the coal and overlying rock. Back analyses were performed on the widespread collapse of a room and pillar mine with an associated 3.9 local magnitude seismic event. Pillar and mine-scale models were constructed using the distinct element method to simulate the mining stages leading up to the collapse. A variety of loading conditions, material properties, and interface properties were evaluated for their effect on unstable failure of single pillars, and the mine-scale model was used to study the evolution of failure during progressive mining. The extent of unstable failure was quantified in these models by calculating the total kinetic energy released during each mining stage. Through the parametric analysis of single pillar models, it was found that softening parameters in either the coal or the coal/ rock interface can individually facilitate unstable failure of pillars, but the combination of the two in a single model produced a much higher release of energy during failure. The results of the minescale model further illustrated the trend as the combination of softening parameters in the coal and coal/rock interface produced a series of failures that most accurately reflected the collapse event at the mine. The method of room and pillar stability analysis demonstrated in this study effectively explores the potential for large coal bumps.IntroductionThe analysis of coal pillar behavior is challenging because natural variability in geologic conditions requires estimation of material strengths and predicted loads for a given mining situation. Large width-to-height (w/h) ratio pillars and deep overburden present an additional challenge, as the failure behavior of such pillars is more complex and may involve unstable, sudden collapse. Empirical methods have improved the success of coal pillar design for a wide range of conditions, but, for deep cover and squat pillar (w/h > 10) geometries, pillar performance predictions are not as accurate (Mark, 2000). As with any empirical approach, more back analysis and the consideration of new variables may help improve understanding and accuracy of future designs."

Jan 1, 2015

By David Hill

"End of panel longwall face recovery is almost certainly the most involved recurring geotechnical problem faced by operators, with major loss potential should problems occur. The paper presents Australian experiences and updates the outcomes of an industry sponsored research project on the geotechnical issues associated with conventional longwall recoveries.A number of critical features of the geotechnical environment, support design and mining geometry have a pronounced impact on ground control during face recovery. A model of roof behaviour at the take-off point has been developed and validated. Key geotechnical issues include low roof competency, an adverse weighting environment, geological structure, horizontal stress concentrations at the gate ends and the capacity and. integrity of the shields. All of these are identifiable either at the support design stage or, at worst, prior to the start of powered support removal, which is the critical stage of the recovery process.Key aspects of the geometry and process are the ability to maintain powered support resistance during bolt-up and recovery, the direction of shield removal, the impact of chutes and the speed of the shield removal process.The author presents case studies that illustrate these issues and the associated ground behavior.INTRODUCTIONEnd of panel face recovery is almost certainly the most involved recurring geotechnical problem faced by operators, with major loss potential should problems occur. However, unlike most geotechnical aspects of coal mining, very little research has historically been undertaken on the issue of conventional longwall recoveries. This is in marked contrast to the design of pre-driven recovery rooms, an issue which has attracted considerable research interest (Thomas, 2008). In 2006, Strata Engineering completed an Australian industry (ACARP) sponsored research project aimed at defining and minimising the geotechnical threats during longwall face recovery (Strata Engineering, 2006). The research project had the overall objective of developing guidelines for the specification of ground control strategies, so as to minimise the likely geotechnical threats relating to the safety, operational costs and production delays associated with the recovery of a longwall face."

Jan 1, 2010

By Takashi Sasaoka

A great deal of coal will be left under the final end-walls in Chinese surface coal mines because of lower slope angle in shoveltruck mining systems and larger mining depths. In traditional surface mining systems, the coal under the end-walls will be buried by the inner dumping site, and these coal resources are generally abandoned. Considering these situations, the application of end-wall mining systems was considered in order to recover the residual coal around the end-wall. This mining system can improve economic benefits by exploiting haulage and ventilation roadways from end-walls and utilizing the existing transportation systems. In order to develop the appropriate pillar design methodology for the end-wall mining system, several empirical formulas and methods were discussed based on the formulas developed so far and the mechanics properties of coal and rocks in the Chinese coal mine. From the results of a series of theoretical and numerical analyses, it can be concluded that the coal pillar width calculated by the Mark- Bieniawski formula may serve as an important reference for pillar design in end-wall mining systems, and the end-wall mining system can increase the coal recovery from residual coal resources around highwall and reduce the effect of underground mining operation on slope stability

Jan 1, 2013

By Ed Van Eeckhout

As part of a U.S. Bureau of Mines-sponsored project on the utilization of "stiff' backflll to minimize potential rock burst hazards, a finite element study was undertaken to predict stresses and displacements around a stope mined up from the 5400 level of the Sunshine mine, Kellogg, Idaho. This stope was to be backfilled using a high-modulus fill. In preparation for that configuration, certain instrumentation was installed near the 5400 level to monitor stress changes. Due to untenable economics, only 2 cuts of the stope were ever made. This paper presents the results of the instrument readings taken during the first cut and compares them with the numerical predictions, as well as presents the modeling results of closure and fill stresses in the stope if it had been mined.

Jan 1, 1984

By Jamal Rostami, Asok Ray, Samer S. Saab Jr., Wenpeng Liu

Ground instability, such as roof or rib failures, is one of the most serious and frequent safety hazards that occur in underground mining, tunneling, and underground construction. The ground-related parameters and features of interest, in assessing roof or rib failures, are location, frequency, and orientation of the joints, voids, as well as rock-strength. These parameters are the main components of rock mass characterization that offers effective strategies for ground support, which, in turn, allow one to mitigate the risks related to ground instability. The main objective of this study is to determine the location of joints and classify rock-strengths by analyzing the drilling data recorded from an instrumented roof bolter while drilling for rock bolt installation during the operational cycle. For this purpose, computer programs based on updated pattern recognition algorithms were developed for joint-detection and classification of rock types to offer an estimated strength. This paper briefly introduces ongoing research on joint detection, especially for joints with an aperture less than 0.125in (3.175mm), by employing an instrumented roof bolter in controlled environments. To improve the capability and precision of joint detection programs in detecting the joints from the drilling data and reducing the number of false alarms, many laboratory tests with various simulated joints and rock-strengths were carried out at a J.H. Fletcher & Co. facility. This paper reviews testing procedures, data analysis, updated algorithms used for joint detection, and discusses the latest round of testing in samples with simulated joints at various angles along the borehole.

Jan 1, 2017

By Xuexin Ding, Weijie Wei, Jinwang Zhang, Yi Chen, Shengli Yang

"Many ultra-thick coal seams exist in Xinjiang and the northern part of the Inner Mongolia. These coal seams are more than 30-40m thick. This kind of the thick coal seam is too difficult to extract in one slice, so the top-coal caving longwall mining method was designed for this purpose. In order to study the movement characteristics of the overburden strata and the development of the ""three zones"" in ultra-thick coal seams, the physical and numerical simulations were carried out based on the in-site condition of Baiyinhua coal mine. The result shows that, when extracting the upper part of the l 5m thick coal seams, the first weighting interval was 50-58m and the periodic weighting interval was I 8-20m. The caving zone, fractured zone and bending and sinking zone were 38m, 92m, and 50m respectively in height. The fractured zone height increased with the advancing distance of the face, but in some localities, a ladder-like distribution due to the periodic weighting existed. When extracting the lower part of the 25m thick coal seams, the roof was extremely broken and the collapse range of overlying strata continued to increase in irregular form.INTRODUCTIONThe thick coal seams occupy 44 percent of coal reserves in China and account for 45 percent of the gross domestic coal production. There are three main methods for extracting the thick coal seams: sublevel mining, large height mining, and longwall top-coal caving (LTCC) (Wang, 2009). Due to the rapid development of LTCC in the past two decades, it has become the most extensively used mining method. It possesses the advantages of high-production, high-efficiency, low development ratio, and low-cost (Yang, Zhang, Chen, and Zhengyang, 2016; Wang and Zhang, 2015). Baiyinhua coal mine's coal reserves are full of uniformly distributed thick coal seams, with the minable thickness of the main coal seam between 25 to 40m, i.e. the main coal seam is an ultra-thick coal seam. Sublevel longwall top-coal caving (SLTCC) which is an efficient method for extracting the ultrathick coal seams has led to multiple disturbances Xie, Chen, and Wang, 1999; Singh and Singh, 1999; Xie, Chang, and Yang, 2009. Therefore, using the case of Baiyinhua coal mine, the movement features of overburden strata and development characteristics of the three zones in ultra-thick coal seams were studied by physical and numerical simulations (Qian, et al, 2003; Qian, 1994)."

Jan 1, 2016

By Chase K. Barnard, Rahul Thareja, Sean Warren, Rajagopala Kallu

"Inflatable rock bolts are commonly utilized for ground support in Nevada underground mines, however, there is limited information regarding what factors influence the bond strength of these bolts. Bond strength is an important parameter in friction bolt support design, and this information is usually not available from manufacturers as a standard. Previous research has investigated the bond strength of friction bolts; however, these studies focused primarily on split set bolts and ground conditions more favorable compared to those commonly encountered in Nevada underground mines. Without site-specific bolt pull-out tests, ground control engineers are required to make assumptions regarding the in-situ bond strength of rock bolts. This is especially a concern for projects in the feasibility and initial development stages before site-specific experience is acquired.The purpose of this paper is to establish confidence in anticipated minimum bond strength for inflatable rock bolts by comparing the bond strength to variable geotechnical conditions using the Rock Mass Rating (RMR) system. To investigate a correlation between these parameters, the minimum bond strength of pull-out tested inflatable rock bolts was compared to the RMR of the rock in which these bolts were placed. Bond strength vs. RMR plots indicate that expected minimum bond strength is positively correlated with RMR, however the correlation is not strong. Cumulative percent graphs indicate that 97% of pull-out tests result in a minimum bond strength of 1 ton/ft and ½ ton/ft in RMR =45 and <45, respectively.Although lower bond strengths are more commonly encountered in low RMR ground, high bond strengths are possible as well, yielding higher variability in bond strengths in low RMR ground. Bond strength of friction bolts relies on contact between the rock bolt and drill hole. Experience in Nevada indicates that RMR is known to affect both the quality and consistency of drill holes which likely affects bond strength. Drilling and bolting in low RMR ground is more sensitive to drilling and bolting practices, and strategies for maximizing bond strength in these conditions are discussed."

Jan 1, 2015

By Anton Sroka, Antoni Tajdus, Axel Preusse, Krzysztof Tajdus

"In Europe, the magnitude and range of mining deformation predicted on the surface have been, in most cases, determined using methods based on Gauss' influence function (e.g., Knothe's theory, Ruhrkohle method, Stochastic method). The increase in the application of numerical methods (finite element method FEM, finite difference method FDM, etc.) provides an opportunity to offer a different approach in describing mining deformations. However, this phenomenon is very complex, and due to numerical limitations, a two dimensional analysis was made (in plane strain) in most cases. Such 2D models could not accurately describe the mining geometry and geological conditions. The authors of this paper carried out the calculations in 3D models which describe a mining situation and the character of the strata in one Upper Silesian Polish mine. Furthermore, the authors include some tips for three-dimensional modeling.INTRODUCTIONThrough the years, many numerical models have been used to describe a phenomenon of underground mining exploitation influence on the ground surface. However, such rock masses are highly disturbed (cracks, fractures, changes in water conditions, etc.), and it is very difficult to suitably describe, in a mathematical manner, such materials. Therefore, many of the numerical models created have been corrected in various degrees.At first, models widely used to describe the behavior of strata in the region of exploitation appeared as elastic models, where scientests assumed that a whole strata behaved in a linearly elastic manner, according to Hook's law. Those models have been modifed to received suitable VALUES (of settlement and range of subsidence troughs. Scientests created this amongst others: elastic models with contact between the rocks layers (Shippam, 1975; Salamon, Chugh and Yang, 1993), elastic models with no tension (Chrzanowska-Szostak, 1988), and elastic models with a contact on the subsidence limit plane (Tajdus K., Tajdus A., 2005). However, in most cases, those models did not bring the expected results and the differences between shapes of measured and the calculated subsidence trough were substantial."

Jan 1, 2010

By Peng Zhang

In previous research, the laminated overburden model from the LaModel program was effectively integrated with Analysis of Retreat Mining Pillar Stability (ARMPS) through ARMPS-like input to create a laboratory version of the new ?ARMPS-LAM? program. This program takes the basic ARMPS geometric input for defining the mining plan and loading condition, and then automatically develops, grids, runs, and analyzes a full LaModel analysis of the mining geometry to output the section stability factor (SF), all without further user input. The initial ARMPS-LAM results were encouraging with a case history classification accuracy of 55% to 71%; however, a few of the input variables that were nominally included in the SF calculation showed independent significance in the classification accuracy. Therefore, in order to further improve the accuracy of the ARMPS-LAM program, an investigation of the SFs calculated by the new ARMPS-LAM program and the ARMPS program is detailed in this paper. The initial results of a linear correlation between the ARMPS-LAM SF and the ARMPS SF showed a strong correlation (R2 = 0.88), with the ARMPS-LAM SF averaging about 8% higher. The difference in SFs between the programs were further investigated, and, ultimately, the results indicated that the laminated overburden model as implemented in ARMPS-LAM distributes relatively more load on the section pillars for depths less than about 1,000 ft and less load for depths more than 1,000 ft. The results of this research highlight the potential for improving the ARMPS-LAM program in the future by implementing a more accurate loading calculation on the section pillars.

Jan 1, 2014

By Dongsheng Zhang, Xufeng Wang, Wei Zhang, Gangwei Fan

"Large-scale longwall mining of shallow coal seams could cause mining-induced fractures to communicate with the surface immediately in Northwest China, leading to a series of mine safety and environmental issues, including crack formation, water loss, vegetation deterioration, land desertification, and spontaneous coal combustion. Therefore, an accurate and effective understanding of the spatiotemporal evolution law of mining-induced fractures in overlying strata and its relationship to upper aquifers is critical. In this paper, the application of the geophysical-chemical properties of radon in mining engineering is explored as a potential solution to the shortcomings of existing surveying methods. A radioactive measurement method is proposed for the detection of the development of mining-induced fractures in overlying strata in the Baoshan Coal Mine (BCM). The on-site trial indicated that the first weighting step is approximately 60 m, the average periodic weighting step is approximately 20 m, and the influence coverage of the advanced abutment pressure is approximately 30 m. The presented method could be used as an indirect technical support to increase the safety of coal mining by acting as a simple, fast, and reliable method of detecting mining-induced fractures in overlying strata.INTRODUCTIONAccording to the latest coalfield prediction results provided by China’s National Administration of Coal Geology (CNACG) (Zhou et al., 2013), China’s coal resources are mainly distributed throughout the West, e.g., Inner Mongolia, Xinjiang, Shaanxi, Shanxi, Ningxia, and Guizhou. Two major coal mining areas have been established in the Northwest and the Southwest, and are typically represented by Inner Mongolia and Guizhou (Zhang et al., 2010). Northwest China is an arid to semi-arid area, where the coal seams are typically shallow and covered by a thin layer of bedrock. In its natural state, the surface’s ecological environment is fragile. Large-scale longwall mining of shallow coal seams could cause mining-induced fractures to communicate with the surface immediately, leading to a series of mine safety and environmental issues, including crack formation, water loss, vegetation deterioration, land desertification, and spontaneous coal combustion. This can propel any potential ecological fragility into a state of actual destruction (Zhang et al., 2011). Therefore, an accurate and effective understanding of the spatiotemporal evolution law of mininginduced fractures in overlying strata has become the theoretical basis of solving the above issues."

Jan 1, 2015