Search Documents

By Sandin E. Phillipson

"On April 5, 2010 a massive dust-fueled explosion at a longwall mine in southern West Virginia claimed the lives of 29 miners. The mine had experienced large gas inrushes from the floor on two known previous occasions, and natural gas was found emanating from floor fractures behind the longwall shields after the explosion, indicating a likely fuel source for the initial ignition. In succeeding months, another longwall mine operating in the same seam 15 miles away encountered smaller inflows of natural gas that halted production from two different longwall faces. Production was halted at a third longwall mine, 30 miles south of the first, in May 2011, when explosive levels of methane were detected inby the longwall face on the headgate. The same mine was evacuated on March 20, 2014 when a series of floor gas feeders were encountered on the longwall face. A literature review indicated that there has been little documentation or description of these events, and that their size and frequency are unknown. The most significant floor gas inrushes in the United States are believed to have been associated with longwall mining in the Pocahontas No. 3 Seam of western Virginia, in which an estimated 5.8 x 107 ft3 of natural gas was expended from a floor feeder on the longwall face over a two-week period (Aul, pers. comm.).A variety of mechanisms and circumstances are associated with methane emanations from underground mines. Hyman (1987) defined an outburst as a violent, simultaneous release of gas and comminuted rock material into a working face or the interior of a borehole, and indicated that certain soft or fractured coals have a propensity for outburst based on gas desorption rates. In this mechanism, reservoirs of autogenic gas hosted in pockets of soft, crushed coal surrounded by harder coal are released suddenly as confining stress is removed by mining. Hyman (1987) also suggested that highly stressed, relatively gassy coal that is penetrated by mining-induced fractures could be outburst-prone. Clayton et al. (1993) and Ulery (2008) recognized the importance of faults as potential conduits for gas from adjacent strata into coal mines, and suggested that biogenic gas trapped in adjacent strata could migrate into mined coal seams due to a pressure differential. Ulery (2008) distinguished between an outburst and a blower, the latter defined as an event expending a large amount of gas over an extended time period, most often emanating from underlying strata, but without expulsion of coal or rock. Methane feeders are further defined as a subset of blowers that continually expend gas over a long period of time but at a lower rate. Many of the mechanisms discussed by Ulery (2008) relate to geologic features that can impound gas within the seam, releasing a voluminous amount when mining breaches the elastic dike, fault gouge, or other geologic structure that had restricted and compartmentalized coalbed methane migration. Thus, the events discussed in this paper can be described as blowers and feeders. However, detailed geological observations of the three longwall mines discussed in this paper appear to indicate a mechanism that is different from those described by Hyman (1987) or Ulery (2008), in that they did not involve coalbed-sourced gas, and the reservoirs were not hosted by coal seams."

Jan 1, 2016

By Anand Bhagwat

Surface control can prevent the falls of ground between primary roof support systems and rib support. Using existing industrial products, and adopting them for mining applications, has historically attained surface control in underground mining. However, the latest innovative solution, a revolutionary wire mesh product, is designed specifically for underground mining applications jointly by Bekaert and Orica. This knotted wire mesh, FlexKnot? 2500 and FlexKnot? 3500, uses smaller gauge, higher tensile strength wires, than a chain link fence or welded wire mesh. The higher tensile wire enables the mesh to achieve greater ultimate load-bearing capacity, with significantly lower overall weight. Test results, obtained at the National Institute for Occupational Safety & Health (NIOSH) Mine Roof Simulator facility, illustrate the comparisons of the new FlexKnot with traditional 8- and 10-gauge welded steel mesh. The FlexKnot is superior in deflection, load-bearing capacity, and stiffness?categories that are critical in achieving safer surface control. It also offers enhanced corrosion resistance because of the galvanized coating applied on the individual wires prior to the knotting process. Case studies from underground coal mine installations confirm that FlexKnot has the ability to significantly reduce installation cycle time and to minimize use and repetitive manual handling of individual mesh panels. An added advantage is the ability to supply FlexKnot in rolls for quick and easy handling for either rib or roof support application. When using rolls, the bolter can install the entire roll with one continuous forward motion, unlike the wasteful back and forth travel for mesh panel.

Jan 1, 2014

By Stephen C. Tadolini, Anthony T. Iannacchione

"Coal burst represented a major hazard for some U.S. mining operations. This paper provides an historical review of the coal burst hazards, identifies the fundamental geological factors associated with these events, and discusses mechanisms that can be used to avoid their occurrences. Coal burst are not common in most underground mines. Their occurrence almost always has such dramatic consequences to a mining operation that changes in practice are required. Fundamental factors influencing coal burst events include strong strata, abnormal strata caving, elevated stresses, critical size pillars and the lack of sufficiently sized barrier pillars during extraction. These factors interact to produce excessive stress, seismic shock and loss of confinement mechanisms. Over the 90 years of dealing with these hazards, many novel prevention controls have been developed including novel mine designs and extraction sequences, most of which are site specific in their application. Without an accurate assessment of the fundamental factors that influence coal burst and knowledge of their mechanisms of occurrence, control techniques may be misapplied and risk inadequately mitigated. INTRODUCTIONCoal burst1are violent failures of ribs, roof or floor in underground mines. They are known to occur in complex ways and often under unique sets of conditions. This has made them extremely difficult to anticipate and control. Assessing coal burst risk requires engineers, managers, and safety professionals to recognize the fundamental factors responsible for these events. This helps practitioners recognize the hazard potential and understand the context in which various controls and barriers should be used. Only then can coal burst events be anticipated andappropriate mitigation techniques deployed.Over the last 90 years, a few coal burst events have been anticipated but most have eluded prediction. The authors examined the historical record (Appendix A) and determined that an inadequate understanding of the initiating geologic factors and their associated mechanisms of occurrence have contributed to the poor predictive capability. The historic record also indicates that control techniques have typically been site specific in their application."

Jan 1, 2015

By Yuanping Cheng, Jingyu Jiang, Qiang Zhang

"With the increase of mining depths, deep-seated coal seams face threats from high ground stresses, high gas pressures, high gas content, and low seam permeability, which significantly increase the likelihood of coal and gas outbursts. Challenges continue to grow in coalbed methane (CBM) extraction fields, especially for short-distance gassy multiple-seams. Research has proved that the most effective way to increase coal seam permeability is to decrease the ground stress. Protective seam mining technology is a surrounding rock control technology, which can effectively reduce the ground stress and increase the permeability of the protected coal seam. In this paper, we try to use upper protective seam mining technology to simultaneously extract coal and gas. Findings are based on a FLAC3D simulation of stress variation during the mining of the No. 12 coal seam in the Daxing coal mine, Tiefa Coalfield, China. Results indicate that, after mining the upper protective seam, the pressure-relief effects of the rock mass generated three belts and five zones below the protective seam, providing the space and time for gas pre-extraction engineering. Within the protected area, the numerical simulation indicates that the stress of the No. 13/14 coal seam reduces 95.84% and 88.25% respectively, while the expansion deformation of the protective seams reach 6.87 ‰ and 6.70 ‰ respectively, which demonstrate that the protective mining technology can provide a significant pressure-relief effect to the outburst-prone coal seam. Combining stress relief in this manner with pressure-relief from engineered gas drainage (performed by crossing boreholes from the floor rock roadway) applied before the mining of the protective seam, it would not only be beneficial to CBM drainage but also can reduce the gas outburst risk of the protected seams.INTRODUCTION Internationally, since France used protective seam mining technology to control coal and gas outburst in 1939, it has been promoted and applied in many countries (?????, 1966). Since 1958, China has taken the mining test and engineering practice of protective seam mining technology in the Beipiao, Tianfu, Nantong, Zhongliangshan, Songzao, Huainan, Huaibei, and other coalfields (Yu, 1992). Long-term theoretical research and mining practice of outbursts and dangerous coal seams show that protective seam mining technology is the most effective, safest, and most economical outburst prevention measure (Cheng, Fu, and Yu, 2009; Hu et al., 2008; Cheng and Yu, 2007). Under the condition of high gas content coal seams, the safety and efficiency of simultaneous extraction of coal and gas can be realized through a reasonable mining sequence and an effective gas extraction method (Cheng and Yu, 2003). The in situ stress distribution of the protective seam (No. 1 coal seam) and protected seam (No. 2 coal seam) during protective seam mining in the Haishiwan coalfield formation (Figure 1) (Li et al., 2014). A comparison of the stress and displacement (five zones and three belts) of the rock mass below the protective seam, and in a multiple-seam context in the Dalong Mine, is shown in Figure 2 (Jiang et al., 2015). After mining protection coal in a close-distance seam group, the small spacing between the coal seams causes the protective coal and the protected coal between part of the rock to crack through each other until the protective layer of gob is through the area. This provides a desorption of gas to the protective layer of the mining space channel, making the coal seam permeability increase to several hundred times and improving the gas discharge capacity (Zhai, 2008)."

Jan 1, 2017

By Keith Heasley

This paper is a retrospective on the development, application, and enhancement of the LaModel program from a personal perspective. The narrative starts with an explanation of the objectives behind the original development of the program and then introduces some of the unique and very practical features of the program. Next, a demonstration of how LaModel was advantageously used to model stresses and displacements in a multiple-seam mining situation with highly variable topography is presented. This is followed by the details of a number of the major enhancements and expansions of the program over the years. A back-analysis of the Crandall Canyon Mine collapse is then briefly presented, along with the associated development of a recommended calibration procedure for the critical input parameters to LaModel. Finally, some of the present research areas are briefly described, and future enhancements are introduced.

Jan 1, 2011

By Bowler Jonathan, Lorraine Kent, Tereza Crisu, Stuart Walker, Nicholas Lightfoot

"It has been the practice in Europe to extract the most economic seams first: taking the seams sequentially, top down, to avoid operating within the fractured strata formed by the subsidence trough above previously mined coal seams. In the 1990s, the UK coal industry found itself at a number of sites having to operate over one or more previously mined seams. This led to specific geotechnical challenges with respect to maintaining economic, safe and stable rectangular roadways with rock-bolted support.Within this paper, the current challenges and mitigation strategies of overmining in the UK are described following the completion of a -three-year European Commission-funded project in 2015. The challenges and mitigation strategies are related to:• A case study with overmining of older workings of variable geometry;• Numerical modeling for overmining layout and support design; and• A case study site planning mine layout when considering future overmining.INTRODUCTIONAt the first case study site, case histories were examined for a mine operating at a depth of approximately 700 meters where five longwall panels were extracted above workings 35-40 m below. The overmining of various extraction geometries below led to challenging conditions in areas of high vertical stress concentration. It was found that results from one longwall panel could be suitably used to predict behaviour in a subsequent panel. The experience was used to update previously existing guidelines on the positioning of roadways in relation to subsidence troughs. Existing guidelines recommended that only as a last resort should longwalls be planned to retreat over narrow pillars, or from solid ground into a subsidence trough. Existing guidelines regarding the layout of overmining panels are conservative, and new work indicates that such multi-seam geometries are possible with appropriate support management strategies."

Jan 1, 2016

By Stephen C. Tadolini, Robert Hawker, Peter Mills, Colin Grubb, Tom Meikle

"In unfavorable strata conditions, it is often necessary to install additional long tendon support as part of a primary support cycle. Although these support systems provide the required additional stability to the roadway installation does have a significant effect on the rate of development. To overcome the slow cure time of Portland cement-type grouts, the use of two component resin systems, such as polyurethanes and urea silicates, have become favorable. However, concerns over low modulus and creep properties has led to the development of a two-component grouting medium that displays the properties of traditional cable grouting materials with the rapid reaction times of pumpable resin systems. This paper describes product testing, application, surface trials, underground trials, and full-scale applications of the Tekthix System in a dynamic underground environment. INTRODUCTION Single-component cement grouts have been used to anchor long tendon supports for many years. They range from high- to low-slump Portland cement and can be slow-setting to fast-setting grouts. However, current cement grouting systems, which includes the grout and equipment, have some disadvantages: 1. Low-slump grouts require pumps that can handle a thick, high-viscosity grout, so choice of pumps is limited. 2. Pumping distance is limited with current cable bolt grout pumps; operators often tend to add water to allow pumping long distance, which adversely impacts the quality and strength of the material. 3. Fast-setting grouts tend to cause issues with pump and line blockages due to the reduced working life of these single-component materials."

Jan 1, 2017

By Brian E. Travis

Recent Developments in the utilization of polymer grid structures for Longwall Shield Recovery operations are discussed. Specifically: various Longwall screen designs and the numerous methods employed during installation. Also discussed is the role of polymer grid structures in head and tailgate mf and rib control and their role in controlling soft bottom often associated in shield recovery operations.

Jan 1, 1993

In recent years, improvements made to the longwall system have accelerated at a faster pace than those made to the gate entry development system. As a consequence, unless planned years ahead of time, extending the panel length is nearly impossible without some innovative approach. At Cyprus Amax Coal's Emerald mine the G panel length was extended by 3,500 ft- by developing three entries across it to facilitate development of its headgate and tailgate entries simultaneously when the adjoining F panel was in operation. After evaluating alternative supporting methods and associated risks, determination was made to backfill these entries and crosscuts using a low strength flyash cement mixture prior to mining thru. Instrumentation was also used to monitor the stress change or front abutment stress in both the coal and the backfilled material ahead of the face. Longwall mining thru these three entries took about four eight-hour shifts and proved to be very successful. The designed flyash cement mixture provided adequate roof stability and caused no difficulty in the shearer's cutting while eliminating an in-panel longwall face move and minimizing the risk of roof or floor failure in the in-panel openings, or in the worst scenario loss of the face during the longwall cutting thru. This approach provided the intended result of extending G panel and recovered about one million tons of coal. This paper summarizes the engineering design of the cutting-thru project and flyash cement mixture, front abutment stress changes within the longwall coal block, backfilled material, and coal pillars ahead of the longwall face, and our underground observations

Jan 1, 1997

By A. Grenoble

The mining of seams in close proximity can greatly accentuate interaction problems. At distances of less than 110 feet vertically interaction can occur for both over and under mining. Research into ground control problems resulting from undermining a previously mined seam has been carried out using finite element and body-loaded photoelastic modeling methods in conjunction with numerous case studies. Analysis of field data was used to validate and expand the model results. Research findings demonstrate situations under which the worst ground control conditions can be expected to occur for a specified geologic environment, depth, innerburden spacing and mining geometry. Special emphasis has been placed on the effects of pillar load transfer on the lower seam in terms of pillar and floor stability and roof control. Roof and floor condition indexes are used to summarize structural and lithologic conditions in the affected seam. The effects of joint orientation and continuity are incorporated in the analysis and the research results have been compiled into a software package for application by the field engineer.

Jan 1, 1984

By Johann van Wjk

Mandatory Codes of Practice to Combat Rock Fall Accidents came into force on South African Collieries in 1997. These were drawn up in accordance with guidelines issued by the Chief Inspector of Mines, The Codes of Practice (CoP's) are legal documents in terms of the South African Mine Health and Safety Act 1996. One of the main results Of the introduction of the COP'S from a practitioner's point of view is that they formalized much of what would have constituted a typical visit to an underground section previously. Other important requirements were as Billows: Support rules and Strata Control Standard Procedures were to be drawn tip. Identification of Special Areas (areas requiring a higher level of rock engineering input and with, typically, higher order of support and restrictions on mining geometries), Changing conditions underground to he identified timeously. Implementation of the CoP to he monitored. To comply with these requirements on Ingwe Collieries (a division of BHPO Billiton Energy Coal) it was decided to produce too separate forms to be used in conjunction with each other. The first of these, the "Underground Section Physical Risk Rating" measures the physical conditions in each section whereas the second form, the "Section Perfomance Rating" determines how well the section personnel are Coping with the conditions. This form also pleasures compliance with the Support Rules and Strata Control Standards. Both forms are essentially risk matrices but with various scenarios described, each with a certain weighting. The "Risk and Performance Form" system for bord and pillar operations has by now been used for five years in the Ingwe and Eyesizwe Mining Collieries and has achieved a great deal of acceptance. This system has enabled the quantification of previously subjective observations and has improved the strata control awareness and management of underground mining sections. Amongst other initiatives it has assisted ill reducing the severity and frequency of fall of-ground accidents.

Jan 1, 2002

By Douglas Scott

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because it can result in failures of ground that lead to both injuries and death. Spokane Research Laboratory personnel investigated electromagnetic (EM) emissions in a deep underground mine in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results suggest that (1) there is no increase in the number of EM emissions prior to recorded seismic activity, (2) some EM signals are generated during blasting, (3) interference from mine electrical sources mask seismic-generated EM signals, (4) EM emissions do not give enough warning (compared to seismic monitoring) to permit miners to leave a stope, (5) the distance an EM signal can travel in the rock is between 17.7 and 39.6 m (58 and 130 ft), and (6) current data acquisition systems do not differentiate between EM signals generated from seismic activity and random mine electrical noise. These results preclude monitoring EM emissions as precursors of impending catastrophic ground failure.

Jan 1, 2004

By Zhou Ying

Based on the mining condition and roof lithology of the 2-3 coal seam at Gengcun Mine, the simulated materials modeling method was used to study the movement process and characteristics of overburden strata movement and to analyze the movement laws of overburden strata during top coal caving mining. Based on the modeling results, variation of the peak abutment pressure and its effect on the top coal's crushing and caving in the mining process was discussed.

Jan 1, 2001

By Gabriel Esterhuizen

The roof rock in underground limestone mines in Northern Appalachia can be subject to high horizontal stresses in spite of the shallow depth of the workings. The high stresses can cause roof stability problems. The National Institute for Occupational Safety and Health staff have observed a distinctive asymmetrical mode of failure at the pillar-roof contact in two underground stone mines, which is different from the typical failure mode observed in response to excessive levels of horizontal stress. A dip of greater than 5° was identified as a possible cause of this mode of failure. Numerical model experiments showed that an increase in the dip of the workings can cause an increase in the stress at the up-dip comer of the roof beam. A case study is presented in which failure at the pillar-roof contact was observed where the dip of the workings was 7° in a high horizontal stress field. Numerical modeling showed that the relatively small dip of the workings could have induced stresses changes in the immediate roof that would explain the failures. The model results also showed that this mode of failure is less likely to occur if the limestone pillars contain weak bedding planes that provide stress relief. In addition, the results showed that for the conditions at the case study site, the stress in the roof beam was not sensitive to the thickness of the roof beam or to the excavation span. The high horizontal stresses at this site are an important contributing factor to the observed failures.

Jan 1, 2004

By Kousick Biswas

The main objective of occupational health and safety research is to minimize or eliminate the events that may cause fatal or non¬fatal injuries to human workers. A commonly used technique is to devise an "incident prevention plan", which is more often the product of thorough investigations of past reported incident events. Incident documentation and methodical reporting and systematic and thorough data collection, often help identify the root cause of the incident - in other words, the etiology of the incident. These retrospective analyses of the incidents can efficiently identify the future steps to take to achieve the objective of minimizing occurrence of "events of interest". This paper introduces a novel technique - "Taxonomic Analysis", which identifies the root causes of an event (an incident in this case) and can provide future direction for corrective measures to reduce the probability of occurrence of the event. A taxonomic analysis involves systematic and organization of data based on observation, description, and classification. This paper utilizes the rock fall related incident narratives, available with the Mine Safety and Health Administration (MSHA) database (1984¬1999), for a taxonomic analysis. The study found that 67.6% of groundfall incidents occurred in supported areas with the remainder (32.4%) in unsupported areas. Some form of rock mass failure appears to cause about 50% of groundfall incidents, although in 39.7% of the overall groundfall incidents or two-thirds of those involving rock mass failure, the exact nature of the rock mass failure could not be determined from the narratives. Human activities factors such as scaling or barring down, drilling or bolting, and setting timbers or cribbing accounted for another 34.5% of the groundfall incidents. Finally, support system failures made up the remaining 15.5%. Results from this taxonomic analysis may suggest focus areas toward which preventive measures and future research activities could concentrate.

Jan 1, 2003

By Larry Howe

Second, or retreat mhng with Mobile Roof Supports (MRS) has now been part of coal mining in the United States for a decade Their utilization has evolved into mining applications which vary in seam heights from 38 inches to 170 inches, and overburden depths from outcrop to beyond 1200 feet This paper will detail the pillaring plans, lift sequences, and mnchky utilized in these operations and the rational for the plans A comparison of the current productivities achieved will be outlined

Jan 1, 1998

By Deno Pappas

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has been evaluating developments in sealant support systems from a ground control perspective. The proper selection and use of a sealant material can significantly enhance ground control which may result in a decrease in worker related injuries due to ground falls. The purpose of this paper is threefold: to briefly review the current state¬of-the-art technology in shotcrete and membrane developments, to evaluate the preliminary findings of a long-terra underground study of various types of sealant materials, and to examine installation practices that are critical for an effective sealant material. The underground study utilizes NIOSH's Lake Lynn Laboratory Experimental Mine to evaluate the long-term performance of several types of shotcrete and membrane materials. Sealant performance to date have been evaluated on a regular basis over a two year period. Although the study is still ongoing, critical mining practices were identified that may seriously effect the bond of the sealant materials to the mine roof and rib; most notably, the importance of scaling and thorough cleaning of the rib prior to application. Also, results from an extensive series of Schmidt Hammer tests found that the shoterete increased in strength by 70% during the humid summer months.

Jan 1, 2002

By Lorraine Kent

Mine tunnel support using rockbolts was introduced in UK coal mines over the period 1987- 1992 and is now used in over 70% of all mine tunnels. In every case the reinforcement design has been based on the observational approach. After the initial reinforcement design has been established appropriate action levels are defined for predetermined amounts of movement indicating the onset of instability. If the action levels are exceeded appropriate remedial action is taken usually in the form of additional support or reinforcement to maintain stability. This paper outlines the observational design method as used in UK coal mine tunnels. It discusses the low cost instrumentation which has been developed to monitor roof deformation, dual height telltales, how action levels are defined based on the geotechnical environment and the types of remedial measures typically taken. An alternative approach for dealing with areas of increased deformation involves reacting to early roof movement trends and modifying the support installed at the face of the development accordingly. Installation of additional support at the face of the heading improves ground control in poor geotechnical conditions and has the advantage of potentially reducing later additional support costs. A case study is described to illustrate how 'early' action levels can be incorporated into a roof support plan enabling a flexible roof support strategy. Such a system will be site specific and continued analysis of monitored information will be required to confirm the action levels or to adjust them according to any change in geotechnical environment. More accurate roof deformation monitoring systems, such as the Remote Reading Telltale system recently developed by Rock Mechanics Technology Ltd. (RMT) and currently undergoing Mines Safety and Health Administration (MSHA) approval, are ideally suited to this application. The Remote Reading Telltale system provides accurate mine wide monitoring of roof condition on a surface PC.

Jan 1, 1999

By John A. Rusnak

Point load testing is used to determine rock strength indexes in geotechnical practice. The point load test apparatus and procedure enables economical testing of core or lump rock samples in either a field or laboratory setting. In order to estimate uniaxial compressive strength, index-to-strength conversion factors are used. These factors have been proposed by various researchers and are dependent upon rock type. This study involved the extensive load France and point load testing of coal measure rocks in six states. More than 10.000 individual test results. From 908 distinct rock units, sere used in the study. Rock lithologies were classified into general categories and conversion factors were determined For each category. This allows for intact rock strength data to he made available through point load testing for numerical geotechnical analysis and empirical rock mass classification systems such as the Coal Mine Roof Rating (CMRR).

Jan 1, 2000

By Eugene D. Krupa

Mine 33 of Beth Energy has serious and complex roof cutter problems causing delay of the advance rate of both the entry development and longwall face retreat. The cost of maintaining these entries is very high due to the requirement of wry heavy artificial supports. It was suspected that this problem was caused by multiple factors including high in-situ horizontal stresses and weak roof in the problem areas. In order to alleviate the problem, proper design of panel entry and roof reinforcement were considered. This paper presents the results of extensive measurements in experimental panel entries of Mine 33 in order to assess the performance of the designed structure and roof support system during the entry development and longwall retreat. An experimental panel entry has been designed and implemented. The designed parameters were varied seeking for the most ideal parameters which provide stable roadways. Changing these parameters accompanied instrumentation of roof, floor, and pillars. Typical instrumentation, including stress meters, convergence measurement stations, and borehole borescope were utilued. Gnensive monitoring of the behavior of the designed structure and support system led to the development of a complete stress-deformation history of the roadway and an ideal roof reinforcement, support system, which reduced the cost of entry development by less than a third of the previous method.

Jan 1, 1990