Search Documents

By Murali M. Gadde

Welded wire mesh is the most commonly used skin control technique in the United States underground coal mines. Currently, selection of the mesh is based on trial and error rather than any rigorous design methodology. Several factors affect a wire mesh?s performance including the amount of rock material to be supported and how the load is distributed, wire gauge, aperture size, grade of steel, weld strength, bolting pattern and sheet size. Although the best way to choose the mesh is to conduct full-scale physical load tests, because of the limitations on the number of variables that can be considered in such tests and the requirement of an elaborate test set-up, it may not always be possible to use this option. An alternative would be to use numerical modeling to study the load-deformation behavior of a wire mesh. In addition to providing a very detailed stress, strain distribution in the entire mesh, the advantage of this approach is the ease with which parametric studies can be conducted. In this paper it is shown that the load-deformation curves generated by nonlinear numerical models match closely with laboratory derived ones. Then, based on parametric studies, design guidelines are developed to choose the mesh appropriate for different loading conditions. The modeling studies also bring forth the limitations of the current lab studies. For example, under some conditions it was noticed that the small sheet size considered in lab tests would produce higher mesh deformations than a full-size one used in actual practice.

Jan 1, 2006

By D. Minney

The quality of resin used in South African collieries is currently controlled according to South African Bureau of Standards, "SABS-1534:2002". It has however been found that resin which passed the SABS tests failed in underground short encapsulation pull tests. An investigation was therefore conducted to determine the characteristics of resins that are currently being used in collieries. A series of in situ short encapsulated pull tests was conducted to determine the effect of expired resin on support performance. The results showed that the longer the time after the expiry date the poorer the resin performance. A series of resin-torque tests has been performed using Anglo Coal's testing facility. The following parameters were investigated on different resins: Spinning speed, Mixing time, and Setting time. An attempt was also made to develop a new quality control procedure for resin. This procedure enables mining personnel to make sure that the quality of resin can provide the required support performance. The effect of spinning speed on resin performance was also investigated. The results showed the resin gelling times of resin decreases as the spinning speed increases. It is found that over-spinning with slow speed roofbolters may result in decreased bond strengths. It was found that a 30-second resin (10-second spin, 30-second hold) should never be spun more than 20 seconds, even with very slow roofbolters (100 rpm).

Jan 1, 2005

By Rob Thomas

Pre-driven recovery roads are used to speed up the longwall recovery process by reducing bolt-up requirements and by improving ground conditions on the face during the removal of the powered supports. To lower the geotechnical risks associated with the use of pre-driven recovery roads, and so improve its overall acceptance in the industry as a viable alternative to more conventional, potentially difficult and costly longwall recoveries, this paper outlines (i) a geomechanical model for the use and design of pre-driven recovery roads, (ii) an updated version of the worldwide database on pre-driven recovery roads, (iii) a summary of the various methods of holing a longwall into a pre-driven recovery road and (iv) a series of relevant ground support and strata management guidelines.

Jan 1, 2008

By Dennis Dolinar

In this National Institute for Occupational Safety and Health (NIOSH) investigation, numerical modeling is used to evaluate the degree the pillar strength is increased with a rectangular pillar over a square pillar. Three-dimensional models are developed with pillar sizes and geometries typical of underground limestone mines in the United States. Physical properties for the models are based on geotechnical surveys of nearly 30 underground limestone mines. To examine the effects of pillar length on pillar strength with the modeling, a parametric study was conducted where the pillar width was held constant while the length and height were varied resulting in width-to-height ratios ranging from 0.5 to 1.5 and width to length ratios ranging from 1 to 6. There are two aspects to pillar strength and failure. At relatively low stresses, pillars can fail as a result of geologic structure. At greater depths and sufficient extraction ratios, the pillars can also fail as a result of the vertical stresses exceeding the pillar strength. The effects of increasing pillar length regarding both strength aspects are presented in this study. Equations were developed for the increase in pillar strength with both height and length based on the model results. The results from these equations were compared to those from previously developed empirical equations for rectangular pillars. For the more slender limestone pillars with a width-to-height ratio below one, there is little increase in pillar strength for length-to-width ratios above 2 and almost no increase with length for a width-to-height ratio of 0.5. Only with the more squat pillars is there a significant improvement in strength with length. The gain in pillar strength with length for the pillars is explained by the change in the ratio of the area of the pillar affected by the ends to the area of the pillar. For the squattest pillar, the change in strength is also affected by an increase in pillar confinement along the central length of the pillar as the pillar transitions from a square to a long rectangular pillar. With geologic structure, added pillar length can significantly improve the pillar strength, depending on the strike of that structure with respect to the long pillar axis.

Jan 1, 2007

By S. Paul Singh

Rock burst is one of the most serious mining hazards, adversely affecting the safety, economy and productivity of mines. It is a sudden manifestation of the release of strain energy stored in the rock mass. At present, there is no universally accepted method for predicting the timing of the rock burst. However, if the seismically hazardous regions in mines can be identified before they are exposed to mining then precautionary measures can be planned before the work begins. A study was conducted in Sudbury Nickel Belt and an approach has been proposed to identify rock burst prone workings on the basis of (a) Rock properties and bursting indices (b) In-situ approaches (c) Geological features (d) Mining conditions (e) Observations during mining operations (f) Comparison and analogy with previous case histories of bursting. This approach will facilitate the judicious application of the burst control techniques to seismically hazardous areas.

Jan 1, 2008

By Nic Slatalla

Acoustic emission monitoring techniques are a powerful tool for analysing deformation behaviour and fracture characteristics of rock samples under uniaxial loading. Uniaxial compression tests were carried out on three different types of sandstone for a better understanding of acoustic emission response with respect to rock deformation and damage develop-ment. All sandstone samples revealed congruent characteristic acous-tic emission patterns which correlated directly with distinct stress-strain stages. However, the acoustic response and development within the individual stages proved to be entirely different due to variations in their microstructure.

Jan 1, 2008

By R. Balia

The upper part of the "Contatto Ovest" orebody, at the San Giovanni Pb-Zn sulphur mine (Sardinia, Italy), is mined by a sublevel caving method. With increasing mining depth, a progressive caving of the hanging wall and discontinuous subsidence occurs. The orebody, which is located very close to the contact between the Cambrian limestones and the Silurian shales, strikes NE-SW for more than 100 m and dips 75-80' NW. The limestone footwall is massive and strong while the hanging-wall consists of very weak shales. The mine considered is located near a town so that the observed subsidence effects must be taken into account for both stability of the nearby railway and houses and morphological and environmental impact. A limiting equilibrium analysis to predict the progress of hanging wall failure with increasing mining depth was used. A suitable computer program was developed for solving the model by a iterative procedure. The progressive hanging wall caving and its consequent superficial effects were predicted perfectly by means of the computer program used and later confirmed by a geophysical test (seismic tomography). Our study ends with a further analysis, carried out using the same procedure, which allows to have a different geometrical situation with the presence of a pillar to protect the mill area.

Jan 1, 1990

By Matt Leeming

Several of the underground mines in the UK require a significant number of cable bolts to be installed, remedially, to control worsening roadway conditions. Often the access is limited and the only power source is compressed air. Machines for this duty are generally designed to perform with 100 psi but regularly only half of this is available. This paper seeks to outline the difficulties this situation causes the Rock Bolting Engineer, highlight the technical requirements for a machine of this type to succeed and detail a solution offered by our engineers.

Jan 1, 2007

By A. G. Pasamehmetoglu

This paper describes the conver¬gence and load measurements carried out in inclined seams at five longwall faces, two of which were supported by hydraulic props and the other three by conventional timber supports in Karadon-Gelik mine. The minimum support capacities determined in this study are compared with the results obtained from two empirical approaches suggested by Wilson (1975) and Jacobi (1981). The characteristics of hydraulic props to be used and support patterns in the longwalls are found, conclu¬sions are drawn and suggestions are made. Design nomograms are prepared for field engineers, in order to be able to approach the problem more confidently and realistically.

Jan 1, 1992

By Anthony Iannacchione

A Major Hazard Risk Assessment (MHRA) was developed in Australia after a series of mine disasters in the 1990?s. A MHRA is used to help prevent major hazards, i.e. fire, explosion, wind-blast, outbursts, spontaneous combustion, roof instability and chemical and hazardous substances, from injuring miners. A MHRA is a structured process that identifies the characteristics of major hazards, assesses and ranks the risk they present, and evaluates engineering and administrative controls to mitigate them. These controls typically consists of a broad spectrum of prevention, monitoring, first response, and emergency response techniques and helps to move an operation from a reactive to a proactive approach towards safety. This paper documents a MHRA performed at an underground mine where strata instabilities and fire hazards may threaten the condition of its escapeways. The objective of this MHRA is to 1) identify what hazards could affect the egress through the mine?s escapeways, 2) determine what unwanted events pose the greatest threat for the mine, and 3) recommend a plan to prevent or recover from the potential disruption of egress through the escapeway. The plan provides information on the key existing controls that should be monitored and audited, and makes recommendation of new potential controls to further reduce related risks. By documenting the use of MHRA to this specific ground control issue, this paper provides a framework for others to judge the merits of this approach and to help design and perform these activities.

Jan 1, 2007

By J. Brasfield

Jim Walter Resources, along with the Rock Mechanics Branch of British Coal and Strata Control Technology Pty. Ltd., is presently studying the yield-stable-yield pillar design in use at the Blue Creek No. 7 Mine located in Brookwood, Alabama. This paper describes the steps taken to determine stresses on the strata surrounding the pre-driven development entries. It also describes the installation and monitoring of stress cells and extensometers used to quantify the stress build-up and strata movement associated with the headgate pass of a longwall panel. The findings of this study will be used to design and predict the performance of a 2 entry yield pillar system in the Parkgate Seam at Welbeck Colliery in the United Kingdom. Stress measurements and strata movement data from No. 7 Mine and Welbeck will be used to develop a computer model that can predict the performance of such a pillar system in British mines. Jim Walter Resources will use this data to study the performance of the present yield-stable-yield pillar system in order to determine if conditions will allow the stable pillar width to be decreased while maintaining current standards of safety and production.

Jan 1, 1994

By Marc Arl

Failures of the face and roof above longwall shields have caused days and sometimes weeks of lost production. A common recovery method for these failures has been to pump light weight cementitious grout into the roof and face cavity to stabilize the area This approach while effective is very time consuming and costly. Mines in several coal producing nations have over the past few years been applying phenolic foam grouts in these situations in lieu of cementitious materials. Phenolic foam is a two-component injection product intended for cavity filling, air and gas sealing and the consolidation of highly fractured strata. The properties of phenolic foam; rapid application, quick setting, high expansion rate, high compressive strength and excellent anti-static properties, produce a fast, safe and cost effective cavity filing solution. The product is also classified as fire resistant and so is also suitable for sealing off underground heatings and for aiding fire fighting operations in deep mines. This paper will discuss the application and use of phenolic foam in various underground coal mines in the world over the past few years.

Jan 1, 2005

By Jeffrey Whyatt

Mining coal in deep, gassy strata is difficult, particularly in deep mines of the west. Dynamic failure (bumps, bounces, etc.) is commonplace, particularly where strong sandstone strata are encountered in the overburden. The disaster potential posed by dynamic failure in these mines is examined and found to be significant. Recent trends in MSHA reportable bumping of deep western coal mines have been increasing. Recent clusters of bumps are explored, a number of which have ended badly. The mechanisms of these bumps and their interactions with geologic structures are explored. Significant progress in controlling these hazards depends on a full understanding of their interaction with geologic conditions. It is apparent that not all MSHA reportable bumps have the same mechanism. These reports describe bumping of pillars, rolling of ribs, outbursts of coal, heaving of floor, shaking-induced roof falls, etc. Progress depends on understanding the underlying mechanisms of these events, and then determining which are potentially active at a particular location. Designs and other protective measures can then be adapted and deployed appropriately. Explicit consideration of mechanisms also supports extrapolation beyond experience as design extends into new mine geometries, geologies, mining methods and increasing depth. Finally, the goal should not be only to design hazard out of mines, but also to provide assurance that this, in fact, has occurred. Pursuit of this goal has been taken up by a major NIOSH research project. The centerpiece of this project is development of a Dynamic Failure Control Program to monitor evolution of dynamic failure hazards with changing geologic conditions to assure that control and protective measures are appropriately deployed.

Jan 1, 2008

By Wenbing Guo

Strip pillar mining method is one of the most important techniques for mining subsidence control in China. Mining depth is one of the most important factors that affect subsidence in strip pillar mining method. Six numerical simulation models were set up in this paper to simulate surface subsidence of strip pillar mining at different mining depths. The mining depth in these models ranged from 300 to 800 m. The simulated results were compared and analyzed. The results showed that the subsidence factor of strip pillar mining is related to mining depth. While other things being equal, the subsidence factor of strip pillar mining increases logarithmically with increase in mining depth. Their quantitative relationship was established based on the simulated results.

Jan 1, 2007

By Nic Slatalla

Resin anchored rock bolts are an effective tool to control the deformation of an underground opening because they combine high support capacity with fast installation. However, there are still numerous shortcomings concerning the understanding and interaction of the system bolt-resin-rock. Field and laboratory test series have been conducted for evaluating the load capacity and bond strength of resin grouted rock bolts in different host rocks under axial load. This paper describes that the behavior and shear strength of the system bolt-resin-rock depends on the rock type and discusses a simple correlation between peak shear strength and shear stiffness in the ratio 1:1000 which may moreover be helpful for estimating rock bolt capacity after installation.

Jan 1, 2006

By Luis Giraldo

The installation procedure of fully grouted rebar bolts requires that the bolt be pushed through the resin grout until it is fully inserted in the borehole. Resin grout is a highly viscous fluid that is forced to flow through the annulus between the bolt and the borehole as the bolt advances. Variables such as bolt insertion speed, bolt vs. borehole diameter and grout viscosity determine the magnitude of the pressure generated ahead of the bolt tip. Under weak rock conditions, the magnitude of the pressure of bolt insertion is often sufficient to initiate hydraulic fracturing along joints or bedding planes that allow injection of grout into the strata leading to significant loss of bolt encapsulation. The grout pressure front has also been linked to gloving, a bolt installation problem that reduces bolt effectiveness. A series of tests were conducted to characterize the pressure of bolt insertion during bolt installation under various conditions. Analysis of the data shows three distinct stages of pressure build up during bolt installation. Understanding of the mechanisms involved may allow development of strategies for controlling the pressure buildup and its negative impact during roof bolting under weak rock conditions.

Jan 1, 2006

By Guo Junfeng

The strength of coal mass saturated with gas is an essential parameter in studying the mechanism of gas and coal outburst, and its prediction method. Up to now, there has not been a method for determining the strength of coal mass saturated with gas. This paper describes a new method whereby the strength of in-situ coal mass can be determined and stored continuously and automatically. The simulation results obtained in the laboratory indicate that the new method allows a fast, reliable, inexpensive and convenient determination of the strength of coal mass.

Jan 1, 1992

By Thomas A. Bailey

Since the advent of longwall mining, various methods and materials have been used during relocation to control the intrusion of the gob in the shield/panline area. (figure 1) Controlling this gob is critical to ensuring a safe, speedy, and productive longwall move. An uncontrolled gob can cause a number of problems, from increased worker exposure to entrapment of equipment to lost production. With an eye toward worker safety and increased productivity, several different methods have been developed to minimize gob intrusion. This presentation will take a look at the history and development of longwall ?screens? and ?mesh?, from chain-link fencing to high-modulus polyester geogrids. The benefits and advantages of these developments will be defined. Since 1994, longwall coal mines have used polymer geogrids during longwall recovery to control intrusion of gob material into the shield/pan line area. As described by Brandon and Collins (1996) in their paper presented at the 15th Ground Control Conference in Golden, CO., mines had used various forms of support, such as welded wire mesh, chain-link fencing, wooden cribbing, props, and steel cable to accomplish this. These methods worked, but were labor-intensive, slow, and provided varying degrees of gob stoppage. Although a few mines still use chain-ink fencing to control the gob, longwall coal mines have generally settled on polyester geogrids to control gob and roof and these mines have been instrumental in providing input in order to develop and improve these geogrids products. he trend during the past twelve years has been to incorporate stronger grids and to eliminate auxiliary reinforcements, such as steel cables and nylon or polyester webbing. A job that once required heavy steel cables, props, and fencing is now accomplished with strong, lightweight, high-modulus polyester grids. When we discuss high-modulus grids, we refer to the ratio between load and strain, as illustrated in figure 2. These grids are woven or knitted from yarns that have been pre-stressed. When these grids come under load, they pick up the load more quickly. This allows less deformation in, in this case, the mine roof. The same principle applies when these grids are used to control the ribs. With less elongation, the grids will hold rib material tighter, thereby keeping travel ways more open.

Jan 1, 2006

By Vincent Scovazzo

This paper compares the two most common pillar design equations used worldwide by John T. Boyd Company; the Mark-Bieniawski Equation, an empirical approach, and the Wilson Equation, an analytical approach. The equations are compared in two ways; by their stress profiles and by the Mark-Bieniawski Equation stability factor. Contrasting the two equations based on the visual comparison of their stress profiles is straight forward but evaluating their resulting pillar designs is problematic. Complications arise due to the differences between the use and development of stability factors for empirical equations and safety factors for analytical equations. To work around these differences, comparisons are made between the two equations by first calculating pillar sizes using the Wilson Equation and then determining the Mark-Bieniawski Equation stability factor for these pillars. Pillars designed using the Wilson Equation were based on site-specific data from 23 mines located in the Americas and Australia. Comparing sizes of pillars designed by the Wilson Equation to the Mark-Bieniawski Equation; the Wilson Equation pillar sizes were smaller in 77% of the cases, similar in 3%, and larger in 20% of the cases.

Jan 1, 2008

By Rob Thomas

Strata management is a critical and now necessary requirement in the New South Wales underground coal mining industry. As a formal and structured process, strata management allows ground support and mining methods to be tailored to the anticipated and encountered geotechnical environment in a controlled manner. In its application, strata management therefore enables operators to identify and control geotechnical hazards and the risks they pose to the mining operation, including risks to personnel safety and mine production. The paper considers recent developments in strata management in the New South Wales underground coal mining industry. Points covered include the statutory requirements stipulated in the Coal Mine Health and Safety Regulations, Geotechnical Hazard Plans, tiered support plans, the Authority to Mine concept, Trigger Action Response Plans and monitoring. Several successful and unsuccessful case studies are included which make specific reference to roadway development and longwall retreat and in doing so, the unique demands imposed by these two different aspects of the mining operation on strata management.

Jan 1, 2007