Search Documents

By Changsheng Song

With increasing depth of coal mining in China, the number of coal and gas outbursts has been increasing for years. By means of destressing the protective seam, the gas in the protected seam is drained to reduce gas concentration in the high gassy seams, thus ultimately attaining simultaneous extraction of coal and gas. Base on the simulated material scale modeling and numerical simulation, the protective seam mining method was practiced at No. 8 coal mine in Pingdingshan city. After extracting the No. 15 seam, the overlying strata movement and the deformation of No. 9-10 protected seam were studied. The experiments showed that it was feasible to destress the protected seams with large interburden thickness. As the protective seam was being mined, the protected seam experienced dynamic movement process and the change in vertical stress in the No. 9-10 seam assumed ?W? shape. When the face had advanced 656 ft (200m) from the setup room, the No. 9-10 seam was fully destressed, resulting in easy gas drainage in the destressed zone. Recommendations on mining sequence of multiple seams mining in the Pingdingshan coal areas were made.

Jan 1, 2008

By Kot Unrug

Mine seals are necessary in nearly every mine to isolate mined-out areas from the ventilation network. There is a large number of seals in active mines and that number continually increases as the development spreads across the reserves. The recent accident caused by the failure of seals in the Sago mine resulted in new regulations. These regulations have been set based on a principle of eliminating the risk of failure, rather than the sound engineering and understanding of the conditions that may cause seal failure during an explosion of methane in sealed areas of the mine including the probability of such occurrences. This paper discusses the following subjects related to mine seals: The potential causes of methane explosions and the dynamic effects of pressure wave propagation. Seal materials and methods of construction in view of the interaction of the seal with the host rock environment as well as requirements for gathering geotechnical data. The design of seal dimensions is based on loading conditions, therefore the probable ranges of such loading is reviewed. There is also discussion of possible methods for shielding of seals from pressure pulses following an explosion. Particular seal?s types are examined in reference to the conditions at the seals location. A novel design is presented that will be a low- cost solution for the sealing of mined out areas. Recommendations are given for further research leading to a rational engineering system for design of new seals in coal mines.

Jan 1, 2008

By Wenquan Zhang

Based on the mining and geological conditions of Wadong Mine, Longkou City, Shandong Province, China, a viscoelastic model with proper creep parameters was established. The 3-D ANSYS was used to simulate surface subsidence, analyze overburden subsidence characteristics, and propose the rational mining and pillar widths for mining in weak rocks and under special mining conditions, and provide the policy makers scientific data for decision making on mining activities.

Jan 1, 2006

By J. Nielen van der Merwe

Rock engineering research and technology development in South Africa only received serious attention in reaction to the Coalbrook disaster in 1960. At the time, a number of gaps in knowledge of rock related matters were identified and in the ensuing years, these were progressively attended to. The paper describes the events that led up to the Coalbrook disaster and reviews the developments that took place afterwards. The effectiveness of the research outcomes are tested by referring back to the disaster. It is concluded that tremendous advances were made but that not all the unknowns were attended to at the same level. The strength of nominally square internal pillars is the one issue that received the most attention, but the strength of barrier pillars, overburden behaviour and loading systems are still largely unknown. Due to the complexity of the remaining unknowns, they can and should be addressed by the application of back calibrated numerical models. There are no readily available simple analytical solutions. The state of mining rock engineering research in South Africa borders on an emergency. More than a 1000 years of aggregate research experience has been lost in the last three years and funding is under severe pressure. There are disturbing parallels between the current positioning of the industry as a whole and the Coalbrook mine in the years preceding the disaster.

Jan 1, 2006

By Ebrahim Ghasemi

Problem statement: One of the most challenging safety problems in room-and-pillar coalmines is controlling roof falls during retreat mining. Roof falls not only cause both fatal and non-fatal injuries to miners, stoppages in mining operations, and equipment breakdowns, but also results in the inefficient recovery of coal reserves. Approach: Sufficient awareness of effective parameters related to roof falls is an important factor in roof control. In this study, the major contributing parameters on roof falls during retreat mining are introduced based upon experience and judgment acquired from extensive retreat mining case histories and a review of relevant literature. Key findings: The main roof fall parameters in retreat mining can be divided into three categories: geological, design, and operational. Key conclusions: The design and operational parameters can be controlled by the engineer and/or operator. By the appropriate selection of these parameters in the design and implementation stages of retreat mining, the roof fall risk can be decreased to an acceptable extent.

Jan 1, 2012

By Bruce Hebblewhite

This paper recognises the 25th year of the Morgantown International Ground Control in Mining Conference, by offering a twenty five year review of ground control in the Australian mining industry ? primarily in underground coal. The paper provides an overview of the developments in ground control design methodologies, practices and products. It not only summarises what has been done, but attempts to highlight at least some of the major issues, significant developments, controversies and areas of contention, plus some of the continuing gaps in our understanding or capabilities as we go forward into the next 25 years. Some of the issues included are in relation to: the development of the high strength bolt and cable reinforcement practices widely adopted today and the contrast between stiff and soft systems; a focus on local detail, at the expense of understanding regional stability concerns; dramatic improvements in the use of, and systems available for underground geotechnical instrumentation and monitoring; some of the ground control management trends, including occupational health and safety concerns, availability of suitably trained staff and legislative requirements; the opposing approaches of the empiricists versus the numerical modellers ? is there some middle ground?

Jan 1, 2006

By Peter B. Lilly

Thank you, Syd, for the kind introduction and for inviting me to give the Keynote Address at this very prestigious gathering of some of the finest intellect and talent in the domestic and international coal industry. CONSOL Energy has been a part of this conference for its entire 24-year existence. We have presented 27 papers over that time. CONSOL employees have also been members of the planning committee for the conference, and we have been pleased to support the event both financially and with many participants. So I am honored to be here with all of you this morning, especially during such a positive period for coal. You can just feel the enthusiasm in this room for our industry, and for this conference. I can tell you, there?s also a lot of enthusiasm and excitement in CONSOL Energy?s boardroom. And our enthusiasm is mirrored on Wall Street. But there remains an ironic twist to all of this attention. Even when times are good, the coal industry seems to go largely unnoticed by the mainstream. Outside of West Virginia and other coal-producing regions, the industry still seems to lack influence and support, at least here in America. As an example, last month, an ABC News crew visited our Blacksville 2 Mine, near here, to do a feature story on increased employment in the coal industry.

Jan 1, 2006

By Paul Singh

Blasting is an integral part of mining activity and is an inherently destructive process. The quality of the rock mass in which an excavation is being driven has a strong influence on the level of dynamic forces to which the rock can be subjected and sustain damage. Though each specific rock mass occurrence is unique, yet there are common rock mass features which influence the outcome of controlled blasting in a similar way. A field study was conducted which involved assessment of blast damage at several operating mines and blasting of small scale models. The effects of block size and strength, joint parameters, ground water, weathering of rocks and rock mass rating on the results of controlled blasting have been investigated and discussed in this study. The influence of number and thickness of weak layers on overbreak control has been discussed in the light of practical data. Critical particle velocity ranges for damage to rock masses with different qualities have been outlined. An approach for the judicious design of perimeter hole pattern and charge concentration has been proposed.

Jan 1, 2007

By Jun Han

Coal has been mined in the Kailuan mining area for more than 130 years. The remaining reserves consist of, in large part, coals that would have been considered economically unminable or technically not feasible by the previous generations. Some of the current operations have to resort to overmining because the lower seams had been extracted in the past. This paper deals with the feasibility and proper layout of mining roadways of overmining carried out in the No. 5 seam of Qianjiaying coal mine of Kailuan mining area using numerical and physical simulation. FLAC2D was used to investigate the characteristics of stress and displacement in the overburden after extraction of the lower seams. It also analyzed the proper layouts of gateroads in the upper seams, i.e. locating them in the stress-relief zone of the gob so that their stability can be easily maintained. In addition, a two-dimensional physical model was constructed for investigation of damages to the upper seams due to mining of the lower seams. Finally, based on the results of investigations, proper gateroads layout was designed and successful extraction was implemented for panel 1357 in the No.5 seam.

Jan 1, 2009

By J. B. Lizak

This paper is not available for inclusion in the Proceedings at the time of printing, but it will be included as an insert.

Jan 1, 1984

By David Oyler

Sonic travel time logging of exploration boreholes is routinely used in Australia to obtain estimates of coal mine roof rock strength. Because sonic velocity logs are relatively inexpensive and easy to obtain during exploration, the technique has provided Australian underground coal mines with an abundance of strength data for use in all aspects of ground control design. However, the technique depends upon reliable correlations between the unconfined compressive strength (UCS) and the sonic velocity. This paper describes research recently conducted by the National Institute for Occupational Safety and Health (NIOSH) aimed at developing a correlation for use by the U.S. mining industry. At three coreholes in Illinois, Pennsylvania, and southern West Virginia, sonic velocity logs were compared with point load tests for a broad range of coal measure rock types. For the entire data set, the relationship between UCS and sonic travel time is expressed by the following equation, where UCS is in psi and t is the travel time of the P-wave in microsec/ft. UCS = 468,000 x e-0.054t (1) The r-squared value for this equation is 0.87, indicating that a strong correlation between sonic travel time and UCS can be achieved with this technique. The paper also addresses the steps that are necessary to ensure that high-quality sonic logs are obtained for use in estimating UCS.

Jan 1, 2008

By Murali Gadde

The immediate floor bed in the Illinois Basin coal mines is often comprised of weak plastic underclay material. Operational and stability problems were encountered in the past due to the low strength characteristics of the underclay floor. Among several indicators of the nature of the floor, Atterberg limits are the most important ones that describe the plasticity behavior of these clayey materials. While several useful and interesting studies were conducted in the past on the Illinois Basin weak floor material, within the knowledge of the authors, a comprehensive database describing the plasticity characteristics of the floor material has never been published. In this paper, a large database comprising over 700 sets of Atterberg limits was put together from 39 inactive and active mines from all the three states covering the Basin. Analysis of this data shows several interesting trends related to the engineering behavior of the floor material. The paper also describes the practical implications of the trends shown by the Atterberg limits.

Jan 1, 2008

By David Hill

The Australian underground coal mining industry is increasingly operating in an environment that challenges traditional concepts of coal pillar design, against a background of heightened expectations and demands from other stakeholders with regard to the protection of both natural surface features and burgeoning civil infrastructure. The result is greater possibility of conflict between mine operators, developers and regulatory bodies, with potential for unnecessary sterilisation of Australia?s coal resources and/or escalating surface development / infrastructure protection costs. On the positive side some significant advances have occurred in the general level of understanding of pillar behaviour and stability, both in Australia and overseas. This paper examines some current issues in coal pillar design, focussing particularly on the application and limitations of analytical models of pillar loading. Established methodologies are reviewed and alternative approaches explored, including examples of key geometrical, geological and probabilistic concepts. Practical experiences from the Southern Coalfield of New South Wales (NSW) are examined for the purpose of highlighting critical variables. Finally, some suggestions are made with regard to the direction and opportunities for future research, with particular regard to coal pillar loading, in the interests of all stakeholders.

Jan 1, 2008

By Rob Thomas

Main gate roof control during longwall retreat is subject to a significant increase in horizontal stress and risk. The implementation and management of an appropriate roof support design is as a result, an imperative requirement for any longwall mine and must in addition to the likely consequences of a roof fall, also consider the variables of the geotechnical environment, associated support costs and practicalities. This paper will therefore summarise a number of recent advances in main gate roof control in the Australian coal industry. Points considered include; (i) the ?Longwall Acceleration? concept, (ii) macro-scale horizontal stress notching, (iii) micro-scale horizontal stress notching, (iv) bedded versus laminated roof types and (v) the type of cable reinforcement used.

Jan 1, 2006

By Khaled Morsy

The tragic incidents at Sago and Darby coal mines in 2006 pointed out the need for stronger seals to resist the blast effects of violent gob explosions. Mine Safety and Health Administration (MSHA) has published the final rule on Sealing of Abandoned Areas in April 2008. According to the final rule, the mine seals for unmonitored gob areas should withstand an instantaneous pressure of 120 psi. Reinforced concrete (RC) seal is one of the feasible options that can be used to meet the final rule. Concrete is a heterogeneous, cohesive-frictional material and exhibits complex non-linear inelastic behavior under multi-axial state of stress. The increased use of concrete as primary structural material requires the development of sophisticated material models to have an accurate prediction of the material response to a variety of loading situations. The constitutive modeling of concrete has advanced considerably in the past three decades. Choosing a reasonable concrete material model is important in order to obtain an accurate mine seal design. This paper attempts to address the effect of different concrete material models on the response of RC seal subjected to dynamic loads from methane explosion. Three concrete models, from ABAQUS library, were selected to address the effect of non-linear behavior of concrete and damages due to tensile and compressive stresses. In addition, a typical and verified concrete material model was used for conducting 3D finite element models simulating the RC seal by ABAQUS, EXPLICIT ver. 6.6.

Jan 1, 2008

By Tingkan Lu

To understand the reinforcing mechanisms of the fully grouted resin bolt and clarify its performance in weak roof strata, the field monitoring investigation using instrumented bolts has been conducted in a coal mine. The total time of monitoring was around ten months. In the first 8 month period, the rock bolt performance relates to the initial development of the gateroad and subsequent time dependent strata response. After 8 months, the rock bolt performance relates to the effect of the approaching longwall mining operation, up to the point where the measuring station was destroyed due to the mining operation.

Jan 1, 1998

By Francis S. Kendorski

Over the past 25 years, the present author has written with several co-authors a series of papers beginning with the landmark paper in the 1st International Conference on Ground Control in Mining in 1981, in turn, based upon U. S. Bureau of Mines (USBM) funded contract research managed by the author with a final report issued in 1979, all concerning this paper?s title subject, Effect of Full-Extraction Underground Mining on Ground and Surface Waters. Initially the work was a summary of British, Russian, and Hungarian experience tailored to United States strata conditions, but has evolved into a consistent and well-documented model of the behavior of strata influenced by full-extraction underground mining such as longwall coal mining. The several strata zones recognized in these works, Surface Fracture Zone, Constrained or Aquiclude Zone, Dilated Zone, Fractured Zone, and Caved Zone, have been observed by several workers in the field. The concepts presented initially 25 years ago have been adopted, rightly or wrongly, by state regulators, ground and surface water researchers, and mining practitioners. The development and utility of these concepts and recent findings will be summarized.

Jan 1, 2006

By Xinxian Zhai

Jining No. 3 Coal Mine, a subsidiary of Yanzhou Coal Company Limited. China, is a super-large modern mine. The coal mine is not only the first one constructed with five-million tons of designed production capacity in China, but also a modern underground coal mine with coal transportation systems by trains and ships, and with a power plant. Based on the hard roof conditions of the sublevel caving coal face in the fault-affected zone, the authors designed rebar and cable bolts for supporting the tailgate that is separated from the gob by a narrow pillar. With extensometers and borescope, strata behavior was systematically studied during tailgate development: (1). Roof convergence is much smaller as well as roof strata separation between inside and outside the anchored zone. (2). The affected zone during tailgate development is approximately 50 m. (3). Because of serious floor heave and obvious rib convergence, the tailgate finally turned into a reversed-trapezoid from the original rectangular shape. (4). There being many joints and fractures in the pillar, coal is crushed from the elastic bedded structure into loose blocky materials. But the tailgate met the service requirements during longwall retreat mining, and demonstrated that the method of roof support was a success. Since then, roof bolting has been widely used for the tailgate of longwall panels at Jining No. 3 Coal Mine. Keywords: coal mine; bolt supporting; tailgate; convergence of surrounding rock; ground control; strata behaviors.

Jan 1, 2007

By Erik Westman

Coal bumps remain one of the industry?s most devastating but least understood phenomena. If changes to the internal conditions of the rock mass could be observed there is hope that bumps could be forecasted. Seismic tomography has been used over the past 25 years in an attempt to image these changing conditions in the vicinity of the longwall face. This paper describes the history and practical considerations of using seismic tomography in bump-prone coal mines. The implementation of seismic tomography at six different longwall mines will be described along with lessons learned. Early studies used mining independent sources of seismic energy, including explosives and sledgehammers. Subsequently more operator friendly sources, such as the mining equipment itself and mining-induced seismicity, were used. Seismic energy sensors have been placed in gateroads and on the surface above the mine. Each of these configurations has associated advantages and disadvantages. Although the results obtained have been encouraging, the application of seismic tomography to monitoring a bump-prone longwall face is still immature. The ultimate goal of clearly imaging changing stress conditions in the longwall panel in a manner that does not inhibit mining operation is still distant, yet drawing nearer. When this goal is achieved, the industry will have a capable tool for identifying locations where bumps are imminent.

Jan 1, 2008

By John E. Feddock

Retreat mining plays an important role in the coal production within Kentucky and the Appalachian Coal Basin. In Kentucky, the majority of retreat mining is performed in the Eastern coal field. However, since September 2004, Kentucky has suffered four mining fatalities during retreat mining operations, and the coal industry has focused attention on the safety concerns associated with retreat mining practices. The Kentucky Department of Natural Resources (KYDNR) engaged Marshall Miller & Associates, Inc. (MM&A) to conduct a study to ensure that retreat mining is utilizing the best technology currently available and that the current available employee training programs afford maximum safety to miners. MM&A studied 34 coal mines that were conducting active retreat mining operations and represent about one third of all the mines with approved retreat mining plans in Kentucky. This paper summarizes the major research work conducted (Feddock and Ma, 2006) and recommends the practical methods for improving safety during retreat mining operations.

Jan 1, 2006