Search Documents

By R. S. Sheeta, C. J. Bise

The search for a more effective means of coping with methane liberation has resulted in the expanded use of seam degasification. Its advantages are measured not only in reducing the hazards due to methane, but also in producing a marketable commodity, the gas itself. However, the success of a methane drainage system is the culmination of many complex factors, the most important being the coal seam permeability. The two most popular drainage techniques used in mining today are the vertically stimulated borehole method and the in-seam horizontal borehole method. The objective of this paper is to determine the permeability range in which the selection of the degasification technique is based primarily on equipment and economic analysis. A discussion of the equipment involved will be incorporated into examples evaluated by the Pennsylvania State University coal methane simulation model.

Jan 1, 1990

By W. M. Schafer, C. F. Luckay, D. A. King

Monitoring devices have been installed at several mine sites to assess the potential for the development of acid rock drainage (ARD) in waste rock, spent ore and tailings material. In addition, instrumentation has been designed for monitoring changes in water quality in pit lakes. These devices monitor temperature, oxygen, water movement and water chemistry in the waste rock pile. This information can be used to evaluate the current and future ARD risks and the effectiveness of caps and covers. The information can also be used in the design of other reclamation strategies that limit ARD development. The instrumentation includes nested thermistors and oxygen sensing ports, neutron access tubes, heat dissipation units (HDUs) and lysimeters. Many of the monitoring devices can be linked to a data logger and telemetry systems, enabling monitoring data to be downloaded from the office.

Jan 1, 1999

A series of laboratory based push and pull tests were carried out to investigate how surface profile influence the load transfer mechanism of bolt/resin interface. Tests were carried out in both 75 mm and 150 mm long steel sleeves. Three types of bolts were examined, they were bolts most commonly used for strata reinforcements in underground coal mines in Australia. The bolts had near equal core diameter but of different profile configurations. The change in the length of the encapsulation sleeve was examined in light of the small number of profiles encapsulated effectively in short 75 mm long sleeves. The results showed that peak loads and displacements were directly related to the height and the spacing of the bolt surface profiles. Profile spacing appears to have greater influence on load transfer capacity than the profile height.

Jan 1, 2006

By Atsushi Sainoki

Induced seismicity is deeply related to various engineering projects entailing anthropogenic in-situ stress change in deep underground. Hence, there is a persistent demand for estimating and mitigating the risk. Significant efforts have been made in simulating induced seismicity with a variety of numerical simulation techniques; however, there are still discrepancies between characteristics of induced seismicity numerically simulated and observed in the field. One of such discrepancies is the simulation of triggered seismicity defined as seismic events caused by an infinitesimal amount of anthropogenic stress change, which is frequently observed in geological structures. The present study aims to develop a methodology to simulate triggered seismicity whilst reproducing a complex stress state in a fault zone. For the purpose, a discrete fracture network within a fault damage zone is first generated. Then, an equivalent continuum model, in which each zone has a different anisotropic compliance tensor, is constructed by employing the crack tensor theory. A fault core is simulated at the center of the model with interface elements. Using the equivalent continuum model, an initial stress condition is simulated with the boundary traction method, which results in a very complex stress state with stress anomalies due to the stiffness anisotropy and heterogeneity. Subsequently, the effective normal stress on the fault plane is decreased in a stepwise manner to induce slip. The result demonstrated that many seismic events are induced on the fault plane with a slight decrease in the confining stress, thus being regarded as triggered seismic event. Further analysis on this seismic activity shows that the magnitude of triggered seismic events is inconsistent with the amount of shear stress drop, implying that a relatively small triggered seismic event could produce a large stress drop, generating locally intense ground motions and thus inducing severe damage to the nearby rock mass.

Apr 26, 2022

By Chris Groccia, Damodara R. Chinnasane

Vale is in the process of resuming mining in the lower 810 ore body (810 OB) below 4130L at Copper Cliff Mine – South Side. Production in the lower 810 OB had continued until it was temporarily ceased in 2017 to allow for the execution of activities associated with Copper Cliff Mine Phase 1 project. While mining the stopes in both the lower and mid part of the 810 OB, a seismic response was experienced that resulted in rockbursts and challenging mining conditions. The majority of the rockbursts experienced in the past were associated with stopes mined in a bottom-up mining sequence under a diminishing pillar situation between 3350L and 3540L. The current mining plan is comprised of both top-down and bottom-up mining fronts using a center-out chevron sequence of long hole open stopes to manage induced stresses. Numerical modeling assessments have been carried out to forecast the response of the rock mass due to the planned mining. Seismicity and stress induced damage surrounding excavations are anticipated, and areas requiring extra attention have been identified. A tactical approach is being used to prepare the area for production, including replacement of ground support elements that are damaged or have insufficient residual capacity, and installation of dynamic support in areas anticipated to experience bulking and/or dynamic loading that would exceed the current support system’s capacity. A series of monitoring programs are being put in place to confirm current conditions, and to monitor the response of the rock mass to proactively implement ground control tactics should the need arise. This paper provides a summary of the approach used to forecast, monitor, and manage the behavior of the 810 OB rock mass response to continued mining at depth.

Apr 26, 2022

By J. Mattern

Performance monitoring, operational practices and ongoing collection of geologic data in open pit slopes all provide valuable information for quantifying potential steepening of subsequent slopes. Mining at the Goldstrike open pit has been ongoing since the early 1980’s, with its share of slope instabilities. In areas where slopes have remained stable, consideration has been made for potential slope steepening of final walls. With the proper available equipment, steepening of bench face angles via pre-split blasting is not an uncommon method for steepening of inter-ramp slope angles. As an alternative at Goldstrike, the commonly used Modified Ritchie Criteria for empirical catch bench width has been adjusted resulting in quantified, rock specific formulas for bench width and rock fall berm placement. The result is an inter-ramp slope angle increase of 2 degrees on a 300m high slope, without the necessary purchases and procedural changes that would be required for pre-split drilling and blasting. The result has shown significant net benefits through reduction in mined waste tons and an increase in gold reserves. Location The Goldstrike open pit is located on the Carlin Trend gold belt in northeastern Nevada USA (Figure 1). The mine has produced over 43 million ounces (1.2M kg) of gold during the past 30 years. Engineering Geology Stratigraphy Figure 2 is a stratigraphic section of the rocks in the Goldstrike open pit. Quaternary alluvium and Miocene materials typically are poorly indurated stiff soils and are not present in all locations. Bedrock units consist of siltstones, mudstones, sandstones and cherts. From top down the major units exposed in the open pit are the Vinini Formation, the Rodeo Creek Unit, and the Popovich Formation. In general, rock mass strength increases with depth.

Jan 1, 2019

By J. Brendan Mclaughlin, Casimir J. Koshinski, Michael V. Rose, Wolfgang Baum

Mercury contamination is a worldwide problem in the mining, smelting, and refining of gold, silver, and copper. In these areas, mercury may be found as a naturally-occurring material in ores and concentrates, and/or in secondary feedstocks such as leach residues, pyrometallurgical treatment residues, refinery by­products, electrowinning electrodes, autoclave discharge solids, and waste water and acid plant sludges. The United States Environmental Protection Agency (EPA) has designated mercury one of the most harmful heavy metal contaminant in the environment and has implemented regulations that prohibit land disposal of characteristically hazardous wastes containing greater than 0.20 mg/1 TCLP mercury without prior treatment, thus increasing the cost of managing these materials. The presence of mercury in mine, smelter, and refinery by­products and wastes severely decreases, and in some cases eliminates, the ability to recover residual metal values from the contaminated material. The lost revenue associated with this disposal, combined with the increased direct cost of waste treatment, and/or disposal and protecting workers and the environment, can adversely affect overall profitability. The safe, efficient, and economical removal of mercury from gold, silver, and copper mining by-products requires a treatment process that is capable of liberating the mercury from the wide variety of compounds and matrices in which it may be contained, reducing the mercury content in the matrix to desired levels, and recovering the mercury in pure saleable form, without producing any secondary solid, liquid, or gaseous wastes. This paper reviews results from commercial operations and pilot scale tests using a thermal process owned and operated by Mercury Recovery Services, Inc. (MRS) to remove and recover mercury from copper acid plant blowdown sludge, Merrill­Crowe precipitate from gold/silver mining operations, and Cottrell and salt slag dusts from a precious metals refinery.

Jan 1, 1997

By Mark W. Johns

The design or optimization of a carbon-in-pulp (CIP) plant requires the determination and setting of a number of parameters to ensure optimum economic performance. A number of these parameters are either fixed, a function of the pulp, interdepen­dent, affect other parameters or outputs, so only a limited number of degrees of freedom exist from a metallurgical point of view. The traditional CIP contactor employs a low carbon concen­tration, a low agitation intensity and a reasonably long pulp residence time. The pump cell contactor employs a high carbon concentration, a high agitation intensity and a reasonably short pulp residence time. The two philosophies are dipolar in nature and the question arises as to which configuration is the optimum configuration for a CIP plant. The carbon particle size is shown to have a small effect on the capital cost of a CIP plant. A decrease in the pulp residence time, an increase in the pulp density, an increase in the carbon residence time, an increase in the agitation intensity and an increase in the number of stages are shown to have a positive effect on the capital cost of a CIP plant. The pulp residence time, the pulp density and carbon particle size are shown to have a small effect on the operating cost of a CIP plant. An increase in the carbon residence time, a decrease in the agitation intensity and an increase in the number of stages are shown to have a positive effect on the operating cost of a CIP plant. The optimum CIP plant, therefore, employs a short pulp residence time, the traditional pulp density, a long carbon residence time, the traditional carbon particle size, the traditional agitation intensity, and the traditional number of stages. Neither the pump cell configuration nor the traditional CIP configurations match the optimum configuration.

Jan 1, 1995

By Gregg Wilkerson

The Blind Springs Hill pumice beds are located 5 miles southwest of Benton, California in the foothills between the Benton Mountain Range and Blind Springs Valley. The best exposures of the pumice are in an area 0.75 miles west of Blind Springs Hill. The pumice is Quaternary ejecta material which came from the rhyolitic volcanoes in the Glass Mountain-Volcanic Tablelands area of Mono County. The pumice beds occur in two distinct layers separated by an unconformity. The upper layer is 0 to 11 feet thick and consists of coarse subangular pumice fragments, some of which are over 1.75 inches in diameter. The lower bed is medium to coarse grained with subangular fragments up to 1.0 inch. The lower bed is 0 to 9 feet thick. Overburden at the Blind Springs Hill deposit varies from 0 to 15 feet. There are approximately 1 million cubic yards of material in the deposit that can be mined. The size distribution in the deposit is mostly fine with only 10.6% of the pumice fragments being over 0.5 inch in diameter, the minimum size needed for stone-wash or acid-wash applications. Suitability of pumice for the textile industry is quantified by standard 15-minute abrasion and absorption tests. In the Blind Springs Hill deposit, the plus 0.5 inch fraction has an abrasion loss of 33% which is too high for stone-wash application but it has an absorption capacity of 36% which makes it suitable for acid-wash applications in the textile industry. The abrasion and absorption properties of this deposit are within the range of those which have been measured for other pumice deposits within the United States.

Jan 1, 1995

By William T. Folwell

INTRODUCTION - CURRENT RAISE BORING PRACTICES Raise boring is a comparatively new tool to the underground mining and construction industries. Underground raise boring, in this country, had its beginning in the early 1960's, in the iron mines of Michigan. These first raises were bored 40 in. and 48 in. in diameter with maximum lengths of approximately 200 ft. Since the late "sixties", the raise boring machine has been accepted by the mining industry as an important machine to increase excavation rates, provide adequate ventilation airways, improve safety, and reduce costs, to name a few of the benefits. The construction industry is now accepting raise boring techniques for hydro-electric power projects, water supply projects, tunnel projects, waste water projects, etc. Raise drills are now capable of boring raises to diameters as much as 12 ft, in the softer rock types. Raise lengths range from 200 ft to as long as 1700 ft. Bored raises, in general, are bored at dip angles ranging from 45º to 90º, depending on the requirement of the raise. The general practice is to drill the pilot hole down to an opening below and up ream the pilot hole to the required diameter. The pilot hole (9-7/8", 9", 11", or 12-1/4" diameter) is generally drilled with compressed air to remove the cuttings. In the event that ground water is encountered and removal of cuttings is impeded, a foaming agent is added to assist in lifting the cuttings. When excessive water is encountered, water is used as the circulation medium and the cuttings are removed by pumping. During the reaming cycle, the cuttings fall by gravity and are removed from the bottom of the raise by conventional methods.

Jan 1, 1997

By H. Lyn Bourne

The is the 14th consecutive year for this column and the 13th in which the royalty data have been tabulated. Some holes still exist in the list of royalties that readers hopefully will fill. Construction aggregates - either sand and gravel or crushed stone - are the most common mineral commodity. In spite of their pervasive use nationwide, royalty information for these commodities has been difficult to acquire from some states. Readers can help. Share information about these missing states and next year there will be fewer states without information. Dennis Bryan sent a copy of a report, "Regional Appraisal of Mineral Materials: Carson City District, BLM." The report was authored by real-estate appraisers. It contains more than 50 references to leases of various construction materials in Nevada and nearby states. It gives a thumbnail sketch of each lease and is a good reference. However, the authors erroneously imply that the royalty rate and the in-place value are the same. Several of this year's new entries come from the report. However, the royalties for landscaping materials vary from state to state and by rock type. Some boulders used for landscaping in Nevada have a royalty reported at $1.10/t ($1/st). At the other extreme is lava from Idaho. Used for the same purpose, it has a royalty range of $11 to $18.70/t ($10 to $17/st). Chuanming Tian of Beijing, China has shared some information about the changing mineral royalty policies in China. China first implemented an oil and gas royalty in 1984. In 1992, the government expanded that to include iron ore. In 1994, the royalty policy was extended to all mineral commodities. At the same time, the royalty rate for iron ore increased tenfold.

Jan 1, 1995

By A. C. Lyons, A. J. Reed

INTRODUCTION A trend which is obvious in the United Kingdom and is thought to be evident in other parts of the Western world is the disproportionate rise in the cost of tunnel mining labour compared with other tunnel cost increases. This disproportionate increase in labour costs has been accompanied by, and may be the result of, a shortage of skilled working labour. To combat this problem there has been a steady increase in the use of machines for excavation and for the erection of tunnel linings to keep the amount of skilled labour working below ground to a minimum. The typical tunnelling cycle, where the ground needs continuous support can be excavation, temporary support, temporary lining, grouting and permanent lining. It is obviously an advantage to combine as many of these operations as possible and carry out as much as possible by machine. Machines have been developed which will, either alone or used in combination with a shield, excavate and, when necessary, temporarily support the excavation. If a segmental lining is used, it can be so designed that it will form the permanent lining and reduce the cycle time and skilled labour requirement to a minimum. In cases in which the ground can be cut accurately to a smooth profile and will stand without support for a sufficient time, the lining can be expanded against the ground and the necessity of grouting eliminated. In cases in which ground will not stand without support, the usual method is to use a bolted lining and to grout behind it preferably as the shield is shoved forward. Whichever technique is used (this is largely determined by the ground) it is an advantage to make the segments as large

Jan 1, 1974

By Warren E. Fife

This paper will discuss the application of a continuous miner using a fixed drum milling type cutting head for the underground mining of hard rock and salt ores. Continuous mining machines of the ripper chain cutting head, oscillating milling cutting head and boring arm designs have been used in rock and salt applications with various degrees of success. The large boring arm miners have been successful in potash, trona and salt, but they have not been successful in mining rock materials like iron ore. The main method used in underground mining rock materials is the conventional drilling and blasting the ore from the solid. This is particularly true for the harder, more abrasive copper and iron bearing ores. The softer salt based ores of potash, trona and rock salt can use several underground mining methods depending on seam conditions. Several of these methods use underground coal mining equipment that has been extensively redesigned to adapt it for use in mining noncoal materials. Conventional mining methods employ the use of a universal cutting machine to undercut or topcut the ore body before face drilling and blasting takes place to produce a smooth parting of the ore. The boring arm continuous miner is widely used in underground mining of potash and trona ores. It produces a tunnel with a smooth semicircular contour which results in good rib and roof stability. The ripper chain continuous miner is also widely used in mining the salt based ores of potash, trona and rock salt. They are used more frequently in Europe than in the United States and Canada. Some reasons for using the mechanical mining machines as opposed to the conventional drilling and blasting techniques for mining hard rock ore bodies are the resulting improved rib and roof control, facilitates selective mining of the ore body, and requires less man-

Jan 1, 1974

By R. Sharma

The heterogeneous distributions of nodule sizes, cover-ages and abundances and the variability of their burial und association with sediments and rock outcrops on the seafloor have emerged as crucial parameters in considering the exploitation potential of the manganese nodules in the central part of the Indian Ocean. Nodules with the long axis measuring from 20 and 40 mm (0.8 and 1.6 in.) account for nearly 60% to 70% of those evaluated from photographic and grab-sample data. In addition, 75% of the nodules (by weight) are between 20 and 60 mm (0.8 to 2.4 in.). The distribution of nodules with abundances ranging from 1 to 20 kg/m2 as well as coverages of 1 % to 90% on the seafloor are important considerations in demarcating the potential areas for nodule mining. The mining of areas with higher concentrations of nodules, such as along slopes associated with less sediment, would result in the enhanced recovery of nodules compared to areas with low nodule concentrations, such as in valleys and plains where thick sediment covers occur. The mining head will encounter substrates such as hard rock exposures, either with or without Fe-Mn encrustations, as well as soft sediment layers in the nodule fields. It must be able to collect buried nodules under sediment cover, and it must be able to negotiate uphill and downhill slopes in mining areas. Mapping prior to mining must delineate areas to he avoided and must define locations to be mined. The requirements suggest that the nodule collector must be a dynamic (active) system with sensors to detect areas of potential nodule concentrations, as well as features that are hazardous (or unfavorable) for mining operations.

Jan 1, 1999

By Rainer Kahrger, Guenter Ewald

The topic of this paper is to demonstrate the development of mobile crushing installations from throughput capacities of 200 tons per hour, to mobile and semi-mobile large- scale crushing installations with throughput capacities of 3,500 up to 10,000 tons per hour. Basis are approximately 140 mobile and semi-mobile crushing installations which have been built since 1956 or were on order in 1987. [FIGURE 1. Total Number of Mobile or Semi-mobile Crushing Plants] Sixteen of these approximate 140 mobile and semi-mobile crushing installations have a throughput higher than 3,500 metric tons per hour. Mobile crushers were developed more than 25 years ago in Europe for the quarry industry, which had special requirements - fairly low capacity, mostly softer and less abrasive material (limestone) and full mobility. So the majority of the units up to about 1980 were fully mobile, having a fairly small capacity and utilizing mainly hammermills, double roll and impact crushers. It was only when the mining industry and large quarries picked up the concept in the early 1980's that a drastic increase in capacity took place. Even though the first mobile crusher in a true mining application went into service in 1971, it took another 10 years before it proceeded in a larger scale. This trend was obviously supported by the drastic fuel price and energy cost increase in the mid 70's. Since the cost of conveying material is substantially cheaper than trucking it, the increase in energy cost, combined with increasing haulage distances provided a strong incentive. Figure 1 shows clearly the throughput distribution of all crushing installations and it also shows the sharp increase in the throughput capacities within the last few years.

Jan 1, 1989

After the war that was nearing an end In early 1945, regular consulting work for Bralorne, the Bradleys, Pennsalt Chemical Co., and a directorship and occasional consulting for Homestake Mining Co. made it almost certain that in spite of my 61 years I would have enough work to feed my family. But this routine work would not provide enough income to lay up funds for the inevitable future when I could no longer do arduous work. And it would not give me the adventure that had first lured me into mining. Therefore I was greatly relieved as well as pleased when, in the 18 months from April 1945 to November 1946, I was asked to make three of the most adventurous as well as profitable examinations that ever came my way. Pati[n]o Mines, Bolivia The first of the exciting jobs was an examination of the Pati[n]o tin mines in Bolivia. After I had unsuccessfully tried to induce Anaconda to purchase these mines In 1915, the World War I crisis that had forced the half-Indian accountant to try to sell the mines had come to an end. The European market for tin improved dramatically, and "Don Simon" was able to borrow money for expenses while the concentrates were still In Bolivia. He took advantage of the favorable conditions by buying adjacent properties and increasing development work until his Bolivian tin mines were the greatest in the world. And his daughter had marled the French Count de Boisrouvain and was cutting a swath In high International society. Pati[n]o wanted to get rid of the drudgery of running a complicated mining Industry in a remote area In Bolivia when the fleshpots of Paris were much more seductive. An added incentive was the fact that his miners had become unruly and had even threatened his 11fe.

Jan 1, 1976

By John L. Schroder

The design of an underground mining operation requires the integration of transportation, ventilation, ground control, and mining methods to form a system which provides the highest possible degree of safety for mine personnel; the lowest cost per ton of product; the most suitable quality of final product, considering its intended use; the maximum percent recovery of the reserve, consistent with cost and subsidence rights; and the minimum disturbance to the environment. The selection of mining method is generally the controlling factor in overall mine design. Some important considerations in the choice of mining method are : 1) Depth of cover over the coal seam. 2) Strength and thickness of rock strata in the overburden. 3) Characteristics of the coal seam, including thickness, nature and location of impurities or irregularities, dip (or pitch), nature and direction of cleavage, hardness, and structural strength of the coal. 4) Nature and strength of the immediate roof (top) over the coal seam. 5) Nature and strength of the floor (bottom) under the coal seam. 6) Presence and amount of explosive gas (methane). 7) Quantity of water likely to be encountered in the mining operation. 8) Any previous or concurrent mining in seams above or below the coal seam to be worked. 9) Any restrictions on recovery required for subsidence control. Topographical and geological reports and maps of the area are usually available from state and federal geological surveys, and contain excellent general information to guide more detailed investigations. Exploratory drilling, and the plotting and analysis of the information thus obtained, are essential steps in any development program, and aid in the correlation and evaluation of information gained by other means. Other good sources of information are operating coal mines that may be in the same seam in nearby properties. Such mines may indicate in advance much about roof control, drainage, ventilation, and other mining problems.

Jan 1, 1981

By Boris K. Krstev

INTRODUCTION The flotation process, in the real industrial complexes, is characterized by the existence of the significant number of the close reciprocal interrelationship between the input and output Darameters. Traditional complexity is appeared with regard to absence of the suitable a priori information for the physico-chemical characteristics of the flotation process. It’s led to needful of taking of consideration about the undefinition which have got the place in the real conditions and application of the statistical methods. The identification of the flotation process through statistical methods is conception of the more-stages procedure, including the collection and previous analysis, the choice of the model structure and valuation method, the estimation of the model un- known parameters and the results interpretation. The essential concept for the subject of this paper belongs to the empirical models ("black-box") and deals with optimizing in constant industrial plant process. The offered method envisages the application of process operation data in order to improve the work process or constant accomplishment of better results for the target function in relation to the former achievement. The optimum process solution isn't afixed value under the influence of various factors, but "a moving point" along the response surface and deviates from the scheme solutions. The evolutive planning method constantly "investigates and approaches" the optimum solution for the selected target function. As a matter of fact the expert operates the plant without interrupting the normal work process. The essential concept of method is to attain changes in the standard conditions, but so limited that they will not effect either production or the product. This method is based on statistical concepts and availability of following the risk of error. The possible influental factors for the flotation process (m=l, 2, 3) is following: the metal content in the feed ore; production level (t/h); grinding fineness in the flotation pulp; pH-values; the consumption of collectors and modifiers The possible target functions are: the recovery of plant capacity, metal recovery in the concentration process and concentration quality. The application of the evolutive operativity method in the chalcopyrite flotation- Bucim concentrator, combines the statistical data and the operator's experience in the interpretation and making a decision which adds up to the precise automatic performance of the process. The advantages of this method in relation to the existing procedure for the flotation process are the following: • The method is unexpensive and losses are reduced to the time necessary to collect the data and record them in the computer. This method provides a constant process control and a quality decision which is better than those brought by an ex- pert with great experience ("hit-and-miss method"). • The method also provides incidental data about the effects. • The method should not be considered as a procedure for solving an incidental problem ("crash program"). • The obtained results must be interpreted by an appropriate expert in order to be considered instructive. MATHEMATICAL STATISTICS Taking into consideration the complexity of the enrichment processes it's necessary the application of "black-box" and mathematical modelling. The presence of the indefinite elements compel us towards the both theory of the probability and mathematical statistics. The mathematical statistics by the mineral processing investigation of the valuable raw materials in the last years has had greater signifance and widely spread application. The application of the mathematical statistics methods for the technological pro- cess analysis and the construction of the mathematical models is bound up by the task putting of the automatic control system de- sign (Fisher R. A. 1941, 1949). The statistical analysis in the enrichment processes is applied formerly, especially in the sampling estimation. Contemporary, in the last years is imposed the tendency of mathematical statistics application for the obtaining of quantity characteristics and quantity valuation from the individual influental factors. Above mentioned tendency in the significant level is based by the mathematical statistics development as a mathematical discipline close connected with the technical cybernetics general joining to the investigated object as a "black-box". Another essential factor in the mathematical statistics development is appeared the created mathematical theory of experiments as a new, to some extent, autonomous statistical domain. The theory of experiments has demonstrated exclusively importance for the investigation of the complex more-factorial processes in the chemistry, mineral processing, metallurgy etc. The investigation by the enrichment processes of the valuable raw materials and their management is possible by the statistical method application. In the same time, it's possible to use the wide-spread traditional methods of the statistical analysis, such as the methods of the dispersion, correlation, regression etc. Also, it may be mentioned above all the methods of the statistical planning of the extreme experiments. The more perspective are representatived some cybernetic methods which are based by the probability as an approach in the process analysis, for example, the identify of the ways and forms, the graph application as an additional instrument in the correlation analysis, the dynamic programming etc. The mathematical statistics application in the laboratory investigation scale is connected above all by the experimented material analysis and the compact representation of the obtained results. The mathematical statistics methods are more varrying and may be applied in the investigations of the wide circle of problems

Jan 1, 1996

By S. L. Bessinger

Introduction Extensive testing in the past ten years has shown that where a uniform natural gamma background is present in the strata bordering a seam, the thickness of the boundary coal left in place after mining can be determined by measuring the attenuation of that radiation (Nelson and Bessinger, 1989). Measurements made by the authors in underground mines in Pennsylvania, West Virginia, Ohio, Illinois and Kentucky and by others in Wyoming and New Mexico have shown the presence of such a gamma background (Nelson. 1989). Natural gamma coal-thickness sensors of several configurations have been tested in mines owned and operated by the Consolidation Coal Company (Consol) in Pennsylvania and West Virginia (Nelson and Bessinger, 1988). This paper describes the installation of a natural gamma coal-thickness sensor on an operating continuous miner. Previous tests had shown that the NGB-1000 coal-thickness sensor manufactured by American Mining Electronics, Inc., of Huntsville. AL, is an accurate, mine-worthy instrument. This large gamma detector consists of a sensing head and a control panel. The sensing head contains thallium-doped, sodium iodide scintillating crystal, which is coupled to a photomultiplier tube. The control panel contains the electronic components required for calibration, count conversion and display to the operator. Methods Conditions at a Consol mine in northern West Virginia require that 10 to 15 cm (4 to 6 in.) of coal be left at the roof boundary of continuous miner development sections. This roof coal is required because the shale of the immediate roof is friable and unstable. In the past, operators have used a dirt band that is usually visible near the top of the seam as a guide in maintaining the proper cutting horizon. However, this is not always reliable. Earlier observation showed that the actual thickness of the coal left on the roof varied widely; further, it was noted that occasional, accidental excursions into the immediate roof required supplementary roof control measures, such as installation of planks or center bolts. Thus, it was concluded that operators needed a better source of guidance for control of the cutting horizon, and a roof-coal thickness sensor was scheduled for installation. The NGB-1000 sensor was installed on a Joy 12CM10 continuous miner in June 1988. The sensing head was mounted on the cutter boom of the miner, and the control panel was mounted in the operator's cab. Power for the sensor was initially derived from an intrinsically safe battery power supply. Initial measurements with the sensor showed that the calibration was the same as that used in earlier tests at two other mines, indicating the uniformity of the natural gamma background above the Pittsburgh seam. Operating personnel were initially skeptical of the instrument's accuracy, and were hesitant to use its readings as a guide in maintaining a proper cutting horizon. Because gamma attenuation, the instrument's operating principle, is somewhat abstract, attempts to demonstrate the instrument's accuracy by explaining that principle were generally ineffective. It was found, however, that an operator could usually be convinced of the usefulness of the instrument by placing a large piece of coal of fairly uniform thickness over the instrument's sensing head and allowing the operator to see that the instrument reading increased by an amount very near his estimate of the thickness of the piece. The mine was provided with seven battery power supplies and a charging station. The charging station was kept in the lampman's office, and the mechanic on each shift was instructed that he was responsible for two battery power supplies each day: a freshly charged one to be taken in at the beginning of his shift and a depleted one to be brought out at the end. This system worked well for a few weeks, but eventually some battery power supplies were left in use so long that their batteries were discharged too deeply to allow recharging. In addition, transport and recharging of the batteries represented an additional task for the mechanics, who were already very busy. Consequently, a request was filed with MSHA to allow the sensor to be powered through intrinsic safety barriers by an electronic power supply connected to machine power. The permit was granted, and the sensor was connected to machine power. After the sensor was connected to machine power, the only operating problem experienced was occasional failure of cables. A supply of the required cables was made and delivered to the mine so damaged cables could be quickly replaced. Much of the cable damage could be eliminated by slight modifications to the miner during a rebuild, so that cables could be installed in more protected locations. After the sensor had been in operation for about two months, a survey was made to determine its effect on continuous miner operations. In previous research, coal thickness measurements made in 88 locations by the natural gamma method were compared to measurements made in the same locations by observing drill cuttings and by inspections of drill holes with a borescope. That research showed that the gamma method is at least as accurate as the other two methods (Nelson and Bessinger, 1989) and is also much easier to use. The object of the survey described here was not to assess the accuracy of the natural gamma measurements. but rather to determine the effectiveness of the sensor output as a guide for the operator in maintaining control of the cutting horizon. Thus a smaller, hand-held gamma detector

Jan 1, 1992

By C. Zhou, B. Whisner, J. Carr

Proximity Detection Systems (PDSs) are used in the mining industry for protecting mine workers from striking, pinning, and crushing injuries when they work in close proximity to heavy machines such as continuous mining machines (CMMs). Currently all Mine Safety and Health Administration (MSHA) approved PDSs are magnetic field based systems which can be influenced by the presence of wire mesh that is commonly used for supporting roof and ribs in underground coal m ines. In this paper, researchers at the National Institute for Occupational Safety and Health (NIOSH) characterize the influence of the mesh on the performance of magnetic PDSs by measuring the magnetic field difference around a CMM caused by the presence of the mesh. The results show that the magnetic fields are generally enhanced by the mesh which causes the PDS detection zones to be increased correspondingly. It was discovered that the fields around the joints of two mesh sections have the greatest enhancement and thus deserve more attention. In addition, it is found that the presence of mesh can also cause a variation in the generator current. The influence of mesh is characterized by the change in the generator current with respect to the distance between the generator and the mesh. It was found that the generator current change caused by the mesh can be significant (on the order of ten) when the mesh is extremely close to the generator (e.g, less than 1 cm) and is negligible when mesh is relatively far (greater than 0.15 m). The findings in this paper can be used to develop guidelines and best practices to mitigate the influence of mesh on PDSs. INTRODUCTION The Mine Safety and Health Administration (MSHA) requires operators of underground coal mines to equip place-changing continuous mining machines (CMMs) with proximity detection systems (PDSs) to protect mine workers from striking, pinning and crushing injuries when they work around these heavy machines. Although a variety of technologies can be implemented for proximity detection, the magnetic-field-based PDS that was originally developed at the National Institute for Occupational Safety and Health (NIOSH) has shown great effectiveness in challenging mining environments and currently all MSHA-approved PDSs are magnetic-field-based systems. As shown in Figure 1, a magnetic PDS typically includes two major components----the magnetic field generator and the Miner Wearable Component (MWC). Magnetic fields are generated by injecting a high electric current into a ferrite-rod antenna sealed in the generator. The magnetic field strength detected by an MWC varies with the distance between the MWC and the generator. In a typical PDS, multiple generators are mounted on different locations of the machine. The relative location/zone of an MWC is determined based on the field strengths from different generators picked by the MWC. Ideally, for a PDS to work properly in the underground, the magnetic fields generated by the different generators should be stable and not vary with the environment, as the system would interpret any variation of the magnetic field as a result of the distance change between the machine and the miner wearing the MWC. In reality, however, this is not always the case since magnetic fields can be altered by a number of environmental factors such as the presence of steel wire mesh that has been widely used in underground coal mines for supporting roof and ribs In this paper, the influence of mesh on the PDS performance is investigated and the magnetic field change caused by the mesh is measured.

Jan 1, 2019