Search Documents

By S. P. Hansen

Gravity sedimentation is one of the most widely used processes for separating solids from liquids whether it be for ore and mineral processing or for treating municipal sewage or industrial wastes. Investment in sedimentation equipment can represent a significant portion of the total capital costs associated with a processing or treatment facility. In spite of the importance of sedimentation, little attention has been devoted in recent years to improving this equipment by applying the basic principles involved in sedimentation. In the water and waste treatment field, design criteria established one half-century ago is still the accepted standard and in reflection of this lack of progress, sedimentation and thickening equipment has remained virtually unchanged. The primary purpose of this paper is to present and describe a new innovation in gravity sedimentation which has been applied to water and wastewater treatment and could definitely have application in the field of ore and mineral classification. A secondary object is to introduce the mixed media filter which has been widely used to treat municipal drinking supplies, industrial process water and to provide tertiary treatment of sewage and industrial wastes. The tube-type clarifier was developed primarily to be applied in the field of water and waste treatment where it was found that it could be used to considerably reduce the size and cost of clarification facilities. A logical extension of the tube clarifier would be to the area of minerals classification, ore separation, and for treating waste water associated with these activities. In water treatment practice, most clarification processes are followed by a filtration step to provide further polishing of the water prior to use. This paper will also discuss the mixed media filter which is graded from coarse to fine in the direction of filtration and is capable of operating at high filtration rates and with greater applied suspended solids loading than other filter designs while providing a high qualify filtrate.

Jan 1, 1970

By Dianne M. Satalic, Peter A. Spencer

Bacterial leaching is a mature technology and has been applied in six commercial plants with others in the design stage or under construction. Bacterial oxidation is a relatively inexpensive process which uses naturally occurring soil bacteria to assist in extraction of base and precious metals. Bacterial oxidation has ini­tially been applied for gold recovery but the technology is now being transferred to base metal leaching with processes already developed for copper, cobalt and nickel. Bacterial oxidation plants often have capital and operating cost advantages over competing technologies and do not need a highly skilled workforce. The most common species found in the conditions used for bacterial oxidation and bacterial leaching are Thiobacillus fer­rooxidans and Thiobacillus thiooxidans. One common species other than Thiobaci!lus found in the commercial bacterial leach cultures is Leptospirillum ferrooxidans. Mixed cultures of the three species named here have formed the basis of the technolo­gy applied in most of the commercial applications of bacterial leaching to date. These bacterial species already mentioned all belong in the classification of mesophiles and have an operating range from 20 to 43°C. One other culture, a moderate thermophile operating over the range 40 to 50°C, has been used in one commercial plant in Western Australia. Bacterial oxidation takes place in acidic solutions under aer­obic conditions. The oxidation reaction normally produces iron (II) in solution which is ultimately conve1ted into the iron (III) form. The pH value falls naturally as the sulphide minerals are oxidised and the starting pH value can fall as low as pH 0.6 as the oxidation reaction proceeds. This paper examines the impact of the technology selection and its application on the design, engineering and operation of a bacterial oxidation plant. The effect of the changes to these para­meters on the cost of the bacterial oxidation plant is discussed.

Jan 1, 1998

By Donald C. Rotherham

The Endako, British Columbia, deposit was initially discovered in 1927 by two local men, Charles H. Foote and Alf Lagdon, who were at that time on a hunting expedition. Four mineral claims were located to cover an area of quartz-molybdenite float that was centered on two small ridges. They subsequently uncovered a 0.5-m (1.6-ft) wide vein on which an inclined shaft was sunk to a depth of 8.3 m (27.2 ft) in 1934. Additionally, a short adit was driven to intersect another vein. Numerous trenches and small pits were also dug. Small test shipments of vein material from this early work were sent to G.S. Eldridge and Co. in Vancouver for metallurgical testing. A concentrate assaying 89.2% MoS, was produced with a recovery reported as 93.3%. The concentrate was essentially free of copper, arsenic, and phosphate. The property was examined by many geologists and engineers during 1934 to 1952, but the only work done was undertaken by the owners in order to maintain their claims in good standing. In 1952, Kennco Explorations (Canada) Ltd. carried out a limited program of bulldozer trenching, sampling, and geological mapping before relin- quishing their option. In 1956, American Standard Mines Ltd. acquired an option on the property, but no assessment work was apparently recorded and the property was allowed to lapse. The key claims were restaked in 1959 by C. Riley and H.T. James of Vancouver. The property was optioned from the new owners by Andrew Robertson in July 1961, and a small amount of trenching was conducted. Robertson, on behalf of his own company, R & P Metals Corp., reoptioned the property in January 1962. The initial results of this work were favorable and justified further exploration. The additional finances required to continue the program resulted in the formation of Endako Mines Ltd. (N.P.L.) on June 21, 1962. Field work by R & P Metals and the first Endako Mines exploration was directed by Bob Couts.

Jan 1, 1991

By Mark L. Mott

The Pittsburgh Safety and Health Technology Center of the Mine Safety and Health Administration (MSHA) has developed the Mine Emergency Responsiveness Development (MERD) program to improve the reaction and re¬sponse of mine personnel in mine emergency situations. The MERD program simulates problems that may occur in underground mine fires and explosions or surface mine accidents. Since its inception in 1982, the MERD program has been presented to MSHA, industry, labor and state government personnel. This versatile program is easily adapted to suit various training requirements. In 1992, a Mine Simulation Laboratory was built at the Natinal Mine Health and Safety Academy, Beckley, WV, to improve training for mine emergencies and prevention and fighting of mine fires. This facility is capability of simulating a coal mine and metal-non-metal mine for training purposes. It has been included in the MERD program to provide realistic and practical training for mine rescue teams and MERD partici¬pants in advanced mine emergency operations. The objectives of the MERD program are to improve the organizational and management skills of the participants in a rescue and recovery operation and provide a better understanding of the importance that various roles have on the overall organization and the importance of their interaction. The MERD program is not intended to provide the participants with all of the abilities and knowledge required to respond effectively to a mine emergency. Rather, it is intended to give the participant an opportunity to experience the emotions, frustrations and successes of a mine emergency without having to actually be involved in one. The participants are expected to return to their regular jobs with a greater appreciation of the environment in which emergency operations take place. Experience in mine emergencies is extremely limited in the industry today. The participants are encouraged to use the knowledge gained during a MERD program to develop or enhance a mine emergency plan suitable to their needs.

Jan 1, 1993

By Tom H. W. Loomis

The department of the Interior is a federation or holding company of several fiercely independent bureaus which have either jurisdiction or expertise - or both - in a wide range of environmental fields. Each bureau is an advocate for its own concerns and an enforcer of its own mandates. This can be confusing to the company operating in the field. I will try to explain our concerns, help you see where we are "coming from," and give you some insight as to how we can help you. Other speakers have stressed the environmental concerns and site selection factors for uranium wastes so I will focus on the concerns of the Department of the Interior and some of the assistance we can give you in this area People are more aware and more concerned about environmental factors now than they used to be. Thus the past decade has brought about an evolution in both siting and design of uranium mill tailings ponds. Site selection criteria used to be simple - find a tract of land as near to the ore supply as possible with enough space and suitable topography for the expected volume of wastes. Site selections in the past have left a legacy of problems to be corrected - radioactive wastes on stream banks and in floodplains, mill wastes in and near established communities, and unprotected wastes subject to constant erosion. This is no longer acceptable environmentally or socially to a newly aware and concerned public. (Series of 30-35 slides showing uranium mine and mill wastes in Western United States. These illustrate environmental problems, reclamation and environmentally acceptable sites. The first group of slides are aerial shots taken in Wyoming and shows a surface mine and mill area. In the various views the pit, overburden piles, mill, and tailings pond can be seen. The next series were taken in Wyoming and New Mexico. These show various views

Jan 1, 1980

By John L. Stauffer, Allan Lipton, Kim Leitzel, Lesley Gaydos, Laurence M. Demers, Douglas C. Kuhn

Eicosanoids and cytokines produced by the alveolar macrophage (AM) are key mediators of pulmonary inflammation and fibrosis resulting from occupational exposure to mineral dust. In order to determine if eicosanoid and cytokine production are altered by chronic inhalation of coal dust, we compared the production of prostaglandin E2 (PGE2), thromboxane A2 (TxA2), leukotriene B4 (LTB4), interleukin 1 (IL-1), tumor necrosis factor (TNF) and platelet-derived growth factor (PDGF) by cultured AM from non-smoking normal human volunteers and coal miners. Inhibitors of eicosanoid biosynthesis were administered to AM from coal miners in order to determine if a link between eicosanoid and cytokine production exists in these cells. Basal PGE2, TxA2, TNF and IL-1 production by AM from active miners was increased compared to AM from normal volunteers. However, the production of these eicosanoids and cytokines by AM from former coal miners was reduced compared to control AM. Administration of the cyclooxygenase inhibitor, suprofen, and the lipoxygenase inhibitor, nordihydroguaiaretic acid, reduced PGE2 and TxA2 production in miners' AM but had no effect on LTB4, IL-1 or PDGF production. Specific inhibition of thromboxane synthase by UK38,485 was associated with a significant reduction in TNF production in active miners' AM but had no effect on PGE2, LTB4 or IL-1 production. The prostacyclin analogue ZK96,480 also specifically inhibited TxA2 production in active miners' AM. The results of these studies suggest that coal dust exposure is associated with alterations in AM eicosanoid and cytokine production which may be relevant to the development of pulmonary inflammation and fibrosis. In addition, the lack of effect of inhibitors of PGE2 biosynthesis on IL1 production in miners' AM suggests the production of these intercellular messengers may not be linked in AM chronically exposed to coal dust.

Jan 1, 1991

By David A. Lindsey

The world-famous beryllium deposits at Spor Mountain, northwest of Delta, Utah, are the principal resource of beryllium in the United States. Beryllium metal, beryllium-metal alloys, and beryllium oxide ceramics have a long history of specialty applications. Beryllium is used in X-ray windows, nuclear reactors: and a wide variety of industrial and electronic products. The Spor Mountain deposits are located on the western rim of the Thomas caldera, one of at least three volcanic depressions that subsided during voluminous eruption of rhyolitic ash-flow tuff in early Oligocene time. Beginning in early Miocene time, the caldera rim and its volcanic fill were cut extensively by basin-and-range faults. Basin-and-range faulting was accompanied by local eruption of high-silica rhyolite. High-silica topaz rhyolites at Spor Mountain (21 Ma) and Topaz Mountain (6 to 7 Ma) are especially rich in fluorine and lithophile trace elements such as beryllium. Topaz rhyolite of the Miocene Spor Mountain Formation, or its magma was the source of the Spor Mountain beryllium deposits. At Spor Mountain, deposits of beryllium, as submicroscopic bertrandite, Be4Si207(OH)2, occur in rhyolite tuff beneath flows and domes of topaz rhyolite. The beryllium deposits also contain minor disseminated fluorite, lithium, uranium, and anomalous traces of other lithophile elements. The host tuff, originally composed of glass, zeolite, and abundant clasts of carbonate rock, has been altered to clay and potassium feldspar. Fluorite, quartz, and opal replaced carbonate clasts in the tuff. Beryllium was deposited with fluorite in altered clasts and in the matrix of altered tuff. Fluorspar and uranium deposits are spatially and genetically associated with the beryllium deposits at Spor Mountain. Fluorspar deposits at Spor Mountain occur mostly in breccia pipes. Some fluorspar pipes contain uranium, thought to be dispersed in the structure of fluorite. Secondary uranium minerals are dispersed throughout the tuff that hosts beryllium deposits and comprise lenses of ore-grade uranium at the Yellow Chief mine.

Jan 1, 2001

By Peter Zhang

The immediate roof at the test site consisted of laminated clay shale that is likely to be susceptible to weathering. With seasonal dry-wet cycles in the mine ventilation air, the roof in the intake air would deteriorate and lose integrity over time. In many instances, the weathering-prone roof would gradually scale off piece by piece between bolts and over the entry corners. In some long-term entries, roof weathering could develop up to 2-3 ft deep with columns of bolted roof hanging under the upper intact roof. If wire mesh is used, the roof bags down and reduces the entry height, and the weight of the bagged roof tends to pull the bolts out and poses a safety hazard. An effective measure is always sought to support this type of weak roof that is sensitive to moisture degradation. One solution is to seal the roof shortly after entry development to prevent moisture penetration so that roof integrity can be maintained for the long term. In this application, a polymer-based sealing material was tested in the Rockspring mine for weathering protection and reinforcement. The material is a one-component polymer powder for spray application onto the roof and rib. The sealant material is mixed with water in the spraying nozzle to apply to the roof and rib as a paste. The product sets within 5-10 minutes and forms a membrane as thin as about 1/8-in. The membrane will quickly develop tensile and bonding strength within minutes and completely cure within a few days. Through sealing, bonding and lateral reinforcement, the integrity of the weak roof can be maintained. The material has been tried in a long-term evaluation over several months in a set of main entries in the Rockspring mine owned and operated by Rockspring Development, Inc., affiliate of Foundation Coal. Preliminary evaluation has shown that the material is an effective and economical solution to ensuring the long-term stability of weathering-prone roof.

Jan 1, 2009

By R. R. Klimpel

Introduction The grinding of coal-water slurries has received increasing industrial attention during the last decade. In particular, there is long-term interest in the use of pulverized coal-water slurries to replace oil in combustion equipment and in the development of coal gasification/liquefaction processes that require coal-water slurries as feed. More specifically, the use of coal-water slurries in gasification requires grinding a high-density slurry containing the smallest amount of water consistent with slurry pumping and spraying. As part of a fundamental engineering research support program aimed at the industrial implementation of dense coal-water slurry grinding, this author has published several papers on how specific rates of breakage vary as a function of slurry rheology (Klimpel, 1982,1982/83). These papers demonstrated that there is a consistent pattern of change in specific rates of breakage of coal in dense slurries with controlled variation in slurry rheology. By matching rheological data with laboratory grinding results, it was possible to identify directly slurry conditions that correspond to: 1) slowing down of breakage rates, 2) the occasional acceleration of breakage of some sizes, and 3) conditions where chemical additives will increase rates of breakage. In brief, these conditions were analyzed using two different criteria: a) the net production rate of material less than some specified size (e.g. kg/min of minus 325 mesh) in a standard batch laboratory mill test as a function of controlled changes in grinding conditions, and b) the use of the one-size-fraction feed method, which consists of following the disappearance of this largest size over grinding time in a batch laboratory mill to arrive at well-known specific rates of breakage (Austin et al., 1984). Detailed references to the methodology used as well as the conclusions are available (Klimpel, 1982, 1982/83) and will not be repeated here. The purpose of this paper is to further demonstrate several additional characteristics of dense coal-water slurry grinding that were shown in a simplified sense in the earlier publications of the author but which have clearly demonstrated themselves as being very important in the industrial simulation and scale-up of such coal-water grinding systems. In particular, this includes the clear and unambiguous demonstration of how the simultaneous acceleration of breakage of some size fractions and slowing down of the breakage of other size fractions is occurring as a function of changes in coal-water slurry density. In the earlier publications (e.g. Klimpel, 1982), it was shown by specially designed experiments that the addition of fine material and/or the use of a chemical thickening agent accelerated the specific rates of breakage of coals of coarser size fractions using the one-size-fraction method. There were also numerous examples given of non first-order breakage (the slowing down of coal breakage rates) using also the one-size-fraction method due to the presence of excessive amounts of fines which corresponded to the development of a rheological yield value. The problem with the simulation and scale-up of any laboratory and/or pilot-scale mill data to an industrial scale using the mechanistic modelling approach involving specific rates of breakage and breakage distribution parameters (e.g. Austin et al., 1984) is the number of assumptions involved in translating the smaller mill breakage parameters to the predicted larger mill breakage parameters. It is apparent, at least to this author, that to accurately simulate and predict larger scale equipment performance from smaller scale data (given that the larger scale data performance is known and hence predictions can be thoroughly checked) requires a better knowledge of breakage parameters than is currently available. More specifically, it was felt that one of the chief problems was the inability of the one-size-fraction method of determining breakage parameters to sufficiently represent the actual magnitude and sometimes even the directions of. the complicated interactions involved with slurry density changes in coal-water slurry grinding. Thus, a special set of experiments was conducted in a somewhat larger batch ball mill (0.457 m diam x 0.610 m length) than the 0.203-m-diam mill used in the original rheology characterization paper (Klimpel, 1982) so as to minimize any unusual effects due to wall-ball interactions (2.54-cm-diam balls used in both mills). More importantly, the measurements of specific rates of breakage were done using a proprietary tracer method on a portion of a given size fraction, which was then remixed into a natural feed size distribution before grinding. The experimental procedure and analysis of subsequent data was done in exactly the same manner as the radioactive tracer technique on coals as originally developed by Gardner (1962). The advantage of such an approach is that it makes no assumptions such as the independence of the specific rate of breakage of any size on the absolute sizes and amounts of other sizes present (both larger and smaller) in the mix of natural feed material. It will be shown that the measured rates of breakage using the direct tracer technique and the one-size fraction method on the same coal are indeed different. In fact, an accurate assessment of what is happening to the rates of breakage as a function of changing slurry density can only he made by measuring particle breakage under grinding conditions approximating the size distributions actually being produced in practice. Experiment procedures and results The pilot mill used was 44 cm diam x 60 cm long with a volume of 91,250 cm3 and was fitted with six 0.5-in. lifter bars.

Jan 1, 1992

By H. Wagner

INTRODUCTION One of the most important tasks facing the opera¬tors of deep-level gold mines is supporting the roof strata in the immediate vicinity of the stope faces. Some of the deeper gold mines operate at depths ex¬ceeding 3.0 km; the extreme mining depths and the tabular nature of the gold-bearing reefs result in high stress concentrations at the abutments of the stope faces. These, in turn, lead to extensive fracturing of even the hardest quartzites. Although most of these fractures develop in a stable manner, there have been many instances where rock failure occurred suddenly, resulting in a considerable amount of damage to the underground workings. Such violent rock failures commonly are known as "rock bursts," and they are typical of many hard-rock mines that are operating at great depths. To safeguard mining personnel and equipment against the effects of stable and unstable rock failures, adequate support must be provided to the fractured roof as quickly and as effec¬tively as possible. Traditionally, timber props and timber packs have been utilized to provide roof support in gold mine stopes up to 1.5 m wide. Both methods of support suffer from the fundamental disadvantage of generating sup¬port only in reaction to movement of the strata. Since unrestrained strata movement often results in a break¬down of the frictional forces that preserve the stability of the intensely fractured roof strata, it is essential that stope supports have rapid load-bearing characteristics. An equally important requirement is that the roof sup¬ports be able to accommodate displacements of the rock mass. A third requirement of roof supports in gold mine stopes is that they must be able to accommodate the high rates of stope convergence typical of rock bursts. The hydraulic prop is the obvious choice for sup¬porting the stope faces in deep-level hard-rock mines. Since hydraulic props can be installed with a positive setting load, they can provide roof support that is independent of strata movement. By equipping the hydraulic props with yield valves, they meet the require¬ment of being able to accommodate rock-mass displace¬ments. However, the requirement of being able to accommodate high rates of stope convergence without overloading or damaging the rock strata was rather difficult to meet. The first introduction of hydraulic roof supports into gold mine stopes showed that conventional hy¬draulic props, such as those used in coal mines, were completely unsuitable for a number of reasons, in¬cluding: 1) Since drilling and blasting are used to break the ore in gold mine stopes, supports installed close enough to be effective are exposed to the vigor of the blast. Conventional coal-mining props suffered extensive blast damage, despite being protected by a blast barricade. 2) The environmental conditions in gold mine stopes favor corrosion. The high quartz content and the abrasiveness of the ore further aggravate the problem by damaging the protective coatings on the hydraulic surfaces. Simply changing the design of gold mine props to have the piston project from the bottom rather than from the top resulted in dramatic improvements in the service life of the props. The improvement was attributable to external water in the stope washing the fine quartz grit away from the hydraulic surfaces, rather than concentrating the particles between the cylinder and piston of the prop. 3) The most obvious deficiency of conventional coal mining props was their inability to yield rapidly enough to accommodate the high convergence rates of rock bursts without overloading the supports. As a result of the first disappointing results with hydraulic supports in narrow hard-rock stopes mined by drilling and blasting, a comprehensive research and development program was undertaken. The hydraulic props resulting from several years of research and exten¬sive field trials are described herein. To date (1978), more than 130,000 of these props have been manufac¬tured and used successfully in a number of mines and under a variety of geological conditions. Although many of the detailed specifications are directed spe¬cifically to gold mining conditions, there are a number of points that are of general importance in the design of underground support systems for tabular excavations in hard-rock mines of any type. SPECIFICATIONS FOR RAPID-YIELDING PROPS Yield Requirements The yield requirements for hydraulic props in deep¬level hard-rock gold mines are summarized in the fol¬lowing paragraphs. Slow Yield Load: The design of the yield valve must allow the yield load to be preset to between 300 and 400 kN. This flexibility is necessary to account for the differences in the strength properties of the roof and floor strata. Drop in Load Under Slow Yield: The drop in sup¬port load during a slow yield should be as small as possible, but it should not exceed 5% of the slow-yield load. Rapid-Yield Load: The load exerted by the prop during periods of rapid stope convergence should be as close as possible to the slow-yield load. The rapid-yield load should not exceed the slow-yield load by more than 15% at yield rates of 1.0 m/s. The limitation of the upper valve of the yield load is important; it deter¬mines the hydraulic performance of the yield valve. The hydraulic props that satisfy this criterion have performed well, even under severe rock bursts. Load Changes Under Rapid Load: On some of the earlier rapid-yielding props, conditions of dynamic in¬stability were observed; these conditions resulted in a complete breakdown of support resistance. It is essen¬tial that the force oscillations during rapid yielding be as small as possible, not exceeding -*5% of the average rapid-yield load at a yield rate of 1.0 m/s. Longitudinal Resilience: During rock bursts, vibra¬tions of the roof and floor sometimes are observed. To

Jan 1, 1982

By R. B. Hoy, Stanley J. LeFond, Unni H. Rowell, K. Reckling, Derek G. Fullerton

In 1989 natural industrial diamonds counted for 55% of the world's natural diamond production. Australia is currently the leading producer (35%). Zaire is the second largest producer (19%). of what is primarily industrial grade rather than gem grade. Botswana (17%) is third, with the former USSR (15%) fourth, and the Republic of South Africa (8%) fifth. Diamonds are also mined in Angola, Namibia, the Ivory Coast, the Central African Republic, Ghana, Tanzania, Guinea, and other African countries. In the Western Hemisphere, Brazil is the principal producer, with some production from Venezuela and Guyana [(Fig. 1)]. A very small output of diamonds is mined today in India, which was the first source of commercial production. In the United States, efforts at commercial diamond mining have been confined to a small area near Murfreesboro, AR. The first diamond was found in a pipe there in 1906. Small scale trial mining has not, however, proved economical. Since diamonds were first discovered more than 2,000 years ago, only about 380 t have been mined. In order to obtain 1 g (5 metric carats) of diamonds, it is necessary to remove and process approximately 25 t of rock. Recovering this small percentage involves a combination of highly developed techniques in mining and extremely sophisticated processes in diamond recovery. END USES Diamonds are used for two unrelated end uses: gem diamonds are jewels of great beauty, while industrial diamonds are essential materials of modem industry. Although imitation stones are substituted for the gem diamond, none of these matches its properties sufficiently well to offer real competition. Synthetic industrial diamonds are now of a quality and size that permit them to be substituted for natural diamonds in numerous industrial applications. For example, synthetic diamonds are available today in sizes up to 100 stones per carat (1.2 to 1.4 mm). In addition, polycrystalline synthetic diamond inserts, such as De Beers Syndite", General Electric's Compaxa and Stratapax", and Megadiamond's Megapax" have replaced natural diamonds in turning tools, mining and oil drilling bits, and dressing tool applications. Industrial Diamonds The diamond is by far the most important industrial abrasive. As recently as 50 years ago, consumption of industrial diamonds was less than that of gem diamonds, but since that time, industrial use has grown to a position of great dominance. During the six-year period 1929 to 1934, the material produced for industrial use amounted to about 74% by weight of the world's total output of diamonds. In 1989 the percentage of natural industrial diamonds mined in the world was 55%. When synthetic industrial diamonds are added to the natural industrial diamond figures, this percentage becomes 87% of total world diamond production including gems, near gems, industrial, and synthetic stones. The many uses responsible for these significant increases are dependent on the properties of the diamond, including hardness, cleavage, and parting, optical characteristics, presence of sharp points and edges, and capacity for taking and maintaining a high polish. The utilitarian role of the diamond was confined primarily to lapidary products until the industrial revolution, which created the first demand for diamond as an industrial tool. In 1777, a British inventor and instrument maker, Jesse Ramsden, used a diamond to cut a precision screw for an engine that he had invented. The first authentic description of industrial diamonds being set in a saw was recorded in 1854 by a Frenchman, Durnain. Eight years later a Swiss watchmaker, Jean Leschot, developed the first diamond drill bit for use in a hand operated machine, which was employed to drill blastholes in rock. In 1864, diamond bits were put to their severest test up to that time in the construction of the Mont Cenis Tunnel in the Alps. A few years later a steam-powered diamond drill with a speed of 30 rpm was able to penetrate rock at the modest rate of 0.3 m/hr. As the industrial revolution gained momentum on both sides of the Atlantic, metal replaced wood and machines replaced people. Thus the foundation was laid for precision engineering and the recognition of diamonds as an indispensable tool of industry. The next major demand for industrial diamonds came after World War I with the development of cemented carbide cutting tools. Diamond was found to be the most effective medium for finishing and grinding the new ultrahard metal. This discovery rapidly increased the demand for industrial diamonds. The availability of inexpensive diamond material inspired tremendous research into applications. By 1935, the first successful phenol-resin grinding wheel containing diamond had been marketed. Soon afterward, the metal-bonded and vitrified diamond wheels were produced, and, as the matrices and bonds that held the diamond grit in place began to improve, the popularity of diamond grinding wheels grew. The outbreak of World War II, and the accompanying increase in use of hard-metal tools in the munitions industry, increased the demand for industrial diamonds. Since about 1950, the development of ultrahard ceramics, semi- conductor materials, plastics, and exotic metal alloys has further consolidated the diamond's position as an indispensable tool of industry. Only diamond is hard enough to cut these superhard materials with the precision, speed, and economy that industry demands today. Special machines equipped with industrial diamonds are used to remove bumps from concrete runways and highways and to modify highway surfaces in order to prevent skid accidents. Many skids are caused by hydroplaning, a phenomenon that occurs when the roadway is wet. Tires mount a film of water and virtually lose contact with the road surface. Diamond machines cut neat, narrow

Jan 1, 1994

Throughout the 1970s, the US Bureau of Mines rode an ebb tide in Washington political circles. In rapid fire succession, the agency lost its mine health and safety enforcement responsibility (1973), a large portion of its energy research responsibility (1975), and then its fuel statistics functions plus a sizable portion of its coal R&D (1977). By 1978, johnny-come-latelies in the Energy, Labor, and Interior Departments had siphoned away from the Bureau some $125 million in program responsibilities as well as 900 of its employees. The bruising decade came to a close with a Department of Natural Resources proposal that, in its original form, would have scattered the Bureau's responsibilities to the winds. "There is no doubt in my wind," said Lindsay Norman, acting director of the Bureau of Mines (see box), "that were the Bureau to continue down the path it was on, the next step was closing the doors and going out of business." The doors are still open, but erosion of responsibilities had a devastating effect on the resources available to fulfill the Bureau's mission. Devastating, too, in terms of internal morale, considering the Bureau had six directors in a 10-year span. "When the troops are in the trenches and are being shot at," Norman said, "they need a leader-hopefully, a permanent one- that can get them advancing. This is something the Bureau did not consistently have in the 1970s." In September 1978, Roger Markle climbed aboard as director of the Bureau to rejuvenate the 70-year-old agency. He resigned only six months later* but the program Markle set in motion is being carried through by Lindsay Norman. Since Norman's appointment as acting director, he has spent considerable time on the road explaining his agency's redefined goals. At one such stop in Duluth, Norman and his two deputy directors, Charles Kenahan and Mike Kaas, answered the following questions. Lindsay, you were the principal architect in the Bureau's 1979 reorganization. How about a glimpse of what that entailed? Toward the end of the 1970s, after almost a decade of steady dismemberment, we reached what we felt was a critical point in the Bureau's history-we had the choice of redefining and strengthening our organization to meet the mineral challenges ahead, or continuing down the path toward the agency's eventual demise. We felt the Bureau's mission too important to abandon, so in 1978 with Roger Markle as director we initiated a six-month, no-holds-barred intro spection of just what the Bureau should be doing, why, and toward what ultimate national needs. And what did this self-reflection reveal? That there is, indeed, a unique federal role for the Bureau of Mines-that of a lead agency for influencing mineral decisions and pioneering tomorrow's technologic advances. Don't confuse us with policymakers, we're not. But we are policy analysts; we're scientists, engineers, and mineral professionals who can offer a sorely needed source of objective, accurate information to decision makers in both the public and private sectors. I feel there is no better brain trust in government than the Bureau when it comes to mineral expertise-of course, I'm biased. Do I understand you to say the Bureau of Mines is an advocate agency for the minerals industry? We plead no parochial interests, nor ought we, but from our viewpoint a sound minerals industry is extremely important to the broader national goals of security and a healthy economy. US dependence on foreign sources for critical minerals, the increasing noncompetitiveness of some US mineral sectors, and the array of land use issues surrounding mineral-rich lands all have much more serious implications than many otherwise informed people seem to recognize. In your estimation, how vulnerable is the US to foreign mineral suppliers? Let me make a distinction between dependency and vulnerability. The

Jan 4, 1980

By Warren D. Stanford

The Alligator Ridge mine is a near-surface gold mine located in a remote area 113 km (70 miles) northwest of Ely, NV. The deposit was discovered in 1976 by a lone prospector working under a grubstake contract for Amselco Minerals Inc. Evaluation of mine potential proceeded quickly. Favorable drilling results led to feasibility and mine design studies by the end of 1978. Mine construction began in early 1980. By September of that year, the process plant was fully operational. The first gold was poured a few months later. Alligator Ridge is designed to produce 1.9 t (60,000 oz) of gold each year. The projected mine life, based on proven reserves, is to mid-1988. However, Amselco is actively conducting exploration nearby for additional reserves to extend the mine's life. Amselco, a subsidiary of the British Petroleum Co., is based in Denver, CO. The company is mine operator and jointly owns the project with Nerco Minerals Inc., a wholly-owned subsidiary of Pacific Power and Light. Alligator Ridge is Amselco's first US mining operation. Geology Alligator Ridge, so named because it appears in outline to be an alligator at rest, contains disseminated micron gold embedded in iron-streaked siltstones. Although definitive conclusions have not been drawn on age and origin, the gold ore bodies are probably young by geological standards. They were formed in a recent volcanic period still evidenced in parts of Nevada by geysers and hot springs. As these superheated solutions rose through the permeable siltstones, they deposited minerals in the rock and formed the present gold ore bodies. During 1977, an extensive soil geochemical sampling program with additional geologic mapping and outcrop sampling were conducted. The results generated several drill targets. Initial drilling was performed in November and December 1977, and ore grade mineralization was encountered in the first drill hole. The Alligator Ridge mine is unusual in relation to other and more recent western US mineral discoveries in that it occupies an area that had no previous mining history. The ore deposits are hosted in upper Paleozoic sedimentary rocks that consist predominantly of a thick carbonate sequence. The main ore host is the Devonian-Mississippian Pilot shale, which occurs locally as a sequence of thin bedded calcareous, carbonaceous siltstones and claystones. The maximum observed thickness of the Pilot section in the mine area is about 140 m (460 ft). Rocks in the Alligator Ridge area have been folded into a series of low amplitude anticlines and synclines that strike north-south and plunge to the south at about 20°, with limbs that dip nearly 20°. The folds have been truncated and deformed by later high-angle faults that generally strike northwest. Although multiple stages of movement are evident on the fault systems, the youngest period of activity is along the major northeast trend. The predominant structural pattern in the area is of the basin- and range-type high angle normal faults. Alligator Ridge is actually a horst block between two basin and range faults. Vantage Ore Deposits There are three principal ore deposits within the Vantage Basin and several smaller satellite mineralized areas. The three Vantage deposits are encompassed in a mineralized zone that covers an area 915 m (3,000 ft) long and 305 m (1,000 ft) wide. All mineralized zones have been outlined by more than 600 rotary drill holes, with an average depth of 150 m (500 ft). Mineralization occurs in both carbonaceous and oxidized rocks. The carbonaceous gold-bearing material is not amenable to current heap leaching practice. Therefore, only oxidized ores are now treated. The carbonaceous gold-bearing material is segregated and stockpiled as it is encountered during mining. The three ore bodies occur along a north-northeast strike, with mineralization becoming progressively deeper from north to south. The ore block dimen-

Jan 6, 1984

By Manfred Hager

The ability of conveyor belts to transport large mass throughputs economically over previously unprepared ground has resulted in this system achieving great and extensive use. A significant component in this development is the conveyor belt itself. The development of high strength steel cord conveyor belts involves the optimising of splice design, the use of excellent rubber material especially in the splice, good craftsmanship during splice production and modern field vulcanisation equipment. The durability of a splice for belts of class St 3000 up to St 790 is expressed by the fatigue strength under dynamic stress. The results obtained with a test method and equipment developed by the University of Hannover indicate the present state of the art in this field. Belts of high nominal strength used on inclined long distance conveyors reach splice fatigue strengths of about 3000 N/mm. The design should only exploit approximately 50% of the fatigue strength determined in the tests as maximum operating stress. IMPORTANCE OF CONVEYOR BELT SYSTEMS The use of conveyor belt technology has expanded considerably over the last decades in the bulk goods transportation sector. Because of the favourable transport costs and the technology's adaptability to specific topographies, belt conveyors frequently represent the most economic solution. When flows of goods are large, as in German lignite mining operations, where masses of up to 40,000 t/h are given, it is the only technically feasible alternative. The use of belt conveyor systems allows the sensible distribution of the waste and the production of the coal (Hager, 1981). But this transportation alternative is also suitable when the masses involved are smaller. Whereas conveyor belts were only suitable for loose bulk goods up until a few years ago, today they are frequently also used for hard rock open cast mines, e.g. in the production of copper ore. Because of the favourable transport costs it is frequently still economic to use mobile crushers with a throughput of up to 10,000 t h 6 which breakdown the large blocks produced y explosives into transportable grain sizes. In many operations, trucks are only used to provide flexibility between the excavator and the crusher, i.e. over short routes, and the long, frequently steep, transport paths to the processing plant or to the spreader are undertaken by belt conveyors (Einenkel et al., 1992). The advantages of belt conveyors, i.e. to cope with large mass flows over inclines and down slopes of up to 1:4 have resulted in this system gaining very extensive use throughout the world. The conveyors can be installed over for the most part unprepared ground with suitable vertical radii, adapted to the locally available belt material. In the process individual conveyor belts with lengths of up to 15 km, and in the underground sector with lift heights of up to 1 km, have been built and operated. This great variety of application possibilities is complemented by a limited ability to pass through horizontal curves. This can be achieved with the help of design measures on the conveyor whilst bearing in mind the characteristics of the belt. STRESSING OF CONVEYOR BELTS IN DIFFERENT TYPES OF PLANT The advantage of conveyor belts compared with other systems is also to be found in the large available service-time window, i.e. the excellent reliability and the low costs of energy consumption and maintenance. It is in particular the reliability of a belt transport system which depends to a great degree on its main component, that is the belt - in all its different types and variations. For this reason, the belt is also given the greatest attention in the development of the individual components, because it is the belt which must be designed optimally with regard to various factors. The specific properties of the conveyor belt then assert a considerable influence on the design and sizing of most other components in a

Jan 1, 1993

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

INTRODUCTION This manuscript is based on site inspections of five existing mines and the detailed analysis of two of the five. The detailed analysis and mathematical models of the two mines are presented herein in order to demonstrate a method of predicting mine water inflow using existing mines as a data base. Water management procedures were studied at all mines. Our original criteria for mine selection were that the mines be less than five years old and have an inflow rate in excess of 2000 gpm (7.6 m3/min). Background hydrologic and hydrogeologic data were required so that two of the mines could be used for our computer modeling experiments. Our original criteria proved to be difficult to meet. We contacted numerous mines via various sources. Many mines were unable to meet the cri¬teria stated or were not interested in cooperating with us. Therefore, we allowed some flexibility in the application of these criteria to satisfy our orig¬inal requirements. Although the visitations at all the mines are not discussed herein the characteristics of the two mines simulated are presented. These simulated mines consist of a uranium mine in New Mexico and a lead mine in Missouri. The mines and owners will remain anonymous by request. URANIUM MINE-CASE HISTORY NUMBER 1 Mine Location The uranium mine that we simulated is located in northwestern New Mexico. The ground surface at the uranium mine is at an elevation of approx¬imately 7000 ft (2134 m) above mean sea level. The climate is arid to semi-arid with an average annual precipitation of approximately 10 in. (25.4 cm) (John and West, 1963). Geologic Setting It is essential that a conceptual model of the stratigraphy, hydrostratigraphy, and structural geology of a mine site be developed prior to simulation by a mathematical model. If such a conceptual model is not developed prior to simulation major errors are difficult to avoid. The uranium mine we have simulated is located in the San Juan Basin (Fig. 68), which is a structural basin located in northwestern New Mexico and adjacent parts of Colorado, Arizona, and Utah. The sedimentary rocks present in the deepest part of the basin are nearly 15,000 ft (4572 m) thick (John and West, 1963). The regional dip of the sedimen¬tary rocks in the Grants area is generally northward toward the San Juan Basin; the regional attitude is modified locally by normal faults and folds (Hilbert, 1963). The rocks of interest in this area are sedimentary in origin and range in age from Penn¬sylvanian to Cretaceous. They rest on the Precam¬brian core of the Zuni Uplift. Associated intrusive and extrusive rocks are of Tertiary and Quaternary ages (Hilbert, 1963). The deepest sedimentary unit of interest at this mine site is the Morrison Formation as described by Hilbert (1963). The Morrison Formation con¬sists of three members in the general area of the mine site; the deepest member is the Recapture. The Recapture Member consists of alternating beds of gray sandstone and grayish red siltstone or mud¬stone with strata up to several feet in thickness. Only a few small deposits of uranium are contained within the Recapture Member. The Westwater Canyon Member overlies the Recapture Member of the Morrison Formation. The Westwater Can¬yon Member is approximately 150 ft (46 m) thick and consists of light brown to gray, poorly sorted, arkosic sandstone, and some interbedded gray mud¬stone. The Poison Canyon Formation denoted in subsequent discussions, tables, and figures was de¬termined to be a part of the Westwater Canyon Member. The separate connotation is used for the description of mining operations and hydraulic properties but a separate physical description is not included. This member of the Morrison Formation contains many large deposits of uranium. This is (some pages in this article are damaged)

Jan 1, 1986

By Michael Elliot-Jones

The fundamental competitive structure in world coal markets will be modified by the entry of such new participants as Colombia and the newer mines in South Africa. The US will, in most markets remain the swing producer, although a number of low cost US mines will continue to compete in world markets. Exchange rate swings will persist as a major hazard for coal exporters.

Jan 1, 1986

By Marie-Josée Banwell, Cyriac Sebastian, Giacomo Falorni, Sara Del Conte

Interferometric Synthetic Aperture Radar (InSAR) is a satellite-based monitoring technique that complements other in-situ methods for detecting and measuring surface displacement. Recent advances in data processing algorithms, coupled with the use of high-resolution satellite systems, make it possible to now provide high-frequency InSAR monitoring services, with updated results delivered every time a new satellite image is acquired. The advent of large, continuously updated data sets, however, brings new challenges, including the need to rapidly sift through the data to identify only those points showing relevant ground displacement information. This has been achieved by using trend variation analysis tools, that quickly isolate and highlight only areas of anomalous behavior. The paper focuses on project case studies where continuous InSAR monitoring has proven to be key in identifying displacement trend changes near tunnel alignments.

Jun 13, 2021

By B. Nyman

A lot of work is in progress to improve copper recovery by leaching-solvent extraction-electrowinning (L-SX-EW). At Outokumpu the focus of attention is on SX equipment development as a result of which a new mixing-settling technology, the Vertical Smooth Flow (VSF) has been introduced. Using helical stirrers in the VSF mixers a more gentle and uniform contacting can be obtained than in the mixing compartments of the low-profile design. The benefits of Outokumpu's new approach are an essential decrease in organic losses and in aqueous in organic entrainments. Separate pumping using a smoothly pre-contacting "Dispersion Overflow Pump" (DOP) is a key feature of the VSF design. The scale-up of this pump as well as the VSF mixers are shown to follow simple mathematical relationships which also have been confirmed by full scale experiments.

Jan 1, 1995

By S. R. Dismuke

Ore at the Magmont Mine in southeast Missouri is extracted by the room and pillar method on two and sometimes three horizons. In 1991, an innovative plan was formulated for recovery of high grade ore in pillars using cable bolts to accommodate spans of more than 27 m (90 ft). A test area was subsequently selected and a recovery plan developed. A cooperative rock mechanics study effort by COMINCO METALS, the U.S. Bureau of Mines and the University of Utah was later established. When initially opened in 1968, the planned production rate was about 1,000,000 tons per year. Due to declining reserves, the production rate was decreased to 630,000 tons per year in November 1992. Pillar recovery now accounts for approximately 40%-50% of the mined tonnage and plays a vital role in allowing Magmont to continue to operate.

Apr 13, 2011

By D. A. Poulter

The stability of a liner system is influenced by many factors which can be compiled into four basic groups. They are: 1. the liner system components and physical characteristics; 2. the geometry and slope of the liner system; 3. the loading conditions on the liner system; and 4. the foundation conditions under the liner system. Failures in the liner system that are due to one or more factors from the first three groups usually result in movement relative to the plans of the liner system. Failures associated with factors in the fourth group result in deformation(s) across the liner system section beyond its design limits. For purposes of these discussions a failure in the liner system refers to displacements or movements resulting in physical damage to the liner system such that it can no longer function.

Jan 1, 1995