Search Documents

By R. D. Kelsey

The theory, definition and practical application of cutoff grades have evolved over a long period. This evolution is reflected in the continuing flow of papers on this and other related matters though the rate has varied as new ideas and theories have become understood and applied in practice. Papers by Lane(l) in 1964 and Taylor(-2)- in 1972 provided landmarks in the understanding and general communication of cutoff grade theory and its application. The reasons for the continuing interest in cutoff grades are obvious. Too high a cutoff can reduce the mineral recovered and possibly the life of a deposit. Too low a cutoff would reduce the average grade (and hence profit) below acceptable levels. This paper provides a brief overview of existing cutoff grade theory and some particular aspects of its application.

Jan 1, 1979

By P. Somasundaran, Brij M. Moudgil

All the major interfacial technologies encountered in mineral processing involve adsorption of surfactants and/or polymers. With the need for processing low grade complex ores it is imperative that conventional techniques such as flotation and flocculation be extended to meet the challenge of treatment of fines. Addition of surfactants or polymers is indeed not limited to the solid-solid separations but extends to particle size reduction in the form of grinding aids and dewatering operations as well. Although progress has been made in recent years to understand the science involved in various interfacial processes, more challenges and opportunities exist today than ever before in processing of the low grade finely disseminated ores. A brief review of the recent advances and the challenges in mineral processing, especially, those related to the interfacial technologies is presented.

Jan 1, 1989

By M. Li, J. D. Miller

Recently water insoluble alcoholic solutions of alkyl hydroxamic acid collectors have been shown to be particularly effective in the flotation of coarse feed material sampled from phosphate operations in Florida, North Carolina and Utah (Miller et al., 2000). The experimental results indicate that high separation efficiencies can be achieved in single stage flotation with these new collectors. In some cases the concentrate grade reached 34% P2O5 with 93% recovery from single stage bench scale flotation experiments. Critical aspects of the composition and structure of these new collectors are discussed with respect to their effectiveness in phosphate flotation. The wetting characteristics at fluorapatite, francolite, dolomite and quartz surfaces are being investigated with the new collector. Finally, other surface chemistry considerations in the development of these new collectors for phosphate flotation are discussed.

Jan 1, 2002

By Y. Q. Zhang, Y. Luo, S. S. Peng

Burrier pillars in underground coal mines could eventually be subjected to a water head due to the build-up of mine water in the old workings. The water head could not only act ns a force to destabilize the pillar, but it could also cause seepage flow through the pillar and its surrounding strata. Excessive seepage flow could induce piping failure that, ill turn, could accelerate the mechanical failure process of the barrier pillars. In this paper, a finite element simulation approach was employed in the evaluation of the barrier pillars. Both the stress distribution and the seepage flow pattern in and around a barrier pillar have been simulated numerically. The effects of ground stress on rock permeability to water seepage has been taken into consideration in these simulations,

Jan 1, 2002

By Joyce A. Ober

Strontium occurs commonly in nature, averaging 0.034% of all igneous rock; however, only two minerals, celestite and strontianite, contain strontium in sufficient quantities to make its recovery practical, and these minerals are found in sedimentary rocks. Of the two, only celestite has been found to occur in deposits of sufficient size to make development of mining facilities currently attractive. Celestite, the most common strontium mineral, consists primarily of strontium sulfate (SrSO,). Strontianite, the second most common mineral, consists primarily of strontium carbonate (Sr CO3). Strontianite would be the more useful of the two common minerals because strontium is used most commonly in the carbonate form, but few deposits have been discovered that are suitable for development. The physical properties of strontium ores are listed in [Table 1].

Jan 1, 1994

Since gold was first discovered in Colorado in the late 1850s' mining has been a major part of the state's economic history, according to Stanley Dempsey, chairman and chief executive officer of Denver- based Royal Gold Inc. While the mining industry has seen some lean times throughout the past century, it has always bounced back. Today, dozens of major gold companies are headquartered in the Denver area. The state's coal mines produced record amounts during 1996. And even some of Colorado's uranium mines are resuming production. Dempsey joined other speakers in addressing the state of Colorado's mining industry during the Colorado Mining Association's (CMA) National Western Mining Conference. Some 800 people attended the CMA meeting, held Feb. 2-5 in Denver. The meeting was the association's 100th since it was incorporated in 1897.

Jan 1, 1997

By R. D. Deister

The Buick concentrator represents state-of-the-art technology in automated digital process control operation utilizing a centralized computer. The process control strategies implemented at Buick are no longer new to the industry, but the successful application of these developments is still rather unique in North America. Productivity improvements, determined to be a direct result of the process control developments, are the primary topics of this paper. Emphasis is placed on metallurgical benefits including both lead and zinc recoveries; lead concentrate grade; and reductions realized in reagent consumptions, operating costs, and personnel. A detailed description of the concentrator, along with a history of the process control development and a more in-depth discussion of the control strategies implemented at Buick can be found in the references. (The Buick flowsheet is depicted in Fig. 1).

Jan 1, 1987

By D. R. Dolinar, J. Pablic, D. C. Oyler, T. P. Mucho

At a mine in central PA, high horizontal stresses have caused long running roof falls resulting in hazardous conditions for the miners and the premature abandonment of panels. Because of these conditions, the mine requested assistance of the National Institute for Occupational Safety and Health (NIOSH) in utilizing the "advance and relieve" method to mitigate the affects of horizontal stress on the mine roof. "Advance and relieve" mining involves the removal of a pillar or a portion of a pillar during development, thereby creating a cave along one side of the panel. Following cave development, the horizontal stress is relieved over the workings adjacent to the cave in the active panel. The mine has used this system in three panels with a significant reduction in stress damage and no large roof falls.

Jan 1, 2001

By Alper Kirmaci, Taghi Sherizadeh, Gunnar Wurst, Paul Brooks, Dogukan Guner, Samuel Nowak, Mina Esmaeelpour, Kutay Karadeniz

As mines continue to deepen and become more expansive, active monitoring of larger volumes of rock mass will become more critical to calibrate numerical simulations and to ensure the safety of underground workers. Monitoring larger volumes of rock mass requires low-cost sensors that are simple in construction and installation. In this study, a novel hybrid optical fiber cable (HOFC) designed for use in distributed optical fiber sensing (DOFS) via grouted boreholes was deployed to monitor a bulk mining operation in an underground metal mine. The HOFC was successfully used to monitor approximately 2.7 × 10 m3 of rock mass above excavations surrounding a pillar removal area in which six large pillars were removed simultaneously. A total of six measurement boreholes (maximum depth of 22 m) were used to measure strain along the optical fiber during the pillar removal operation using the HOFC, allowing for 70 individual strain measurement points, which were constructed for under one U.S. dollar each. Monitoring of the excavation area took place over a 44-day period after pillar removal. Extensional strains were noted in the areas closest to the removed pillars, while areas of compression were noted directly above the remaining pillar in the area. The results of the case study demonstrate that a low-cost optical fiber strain sensing network can be rapidly installed in a large excavation area and can provide highly sensitive strain measurements in a manner that would be cost prohibitive using other methods.

Oct 1, 2024

By Allan Neal, Jess W. Smith

FirstMiss Gold Inc., formerly FRM Minerals, Inc., is heap leaching gold from difficult, low grade ores at the Getchell Gold Mine in Humboldt County, Nevada. A two-thousand ton per day facility is leaching material from waste dumps from old operations and from small, satellite deposits around the main orebody. A three-thousand ton per day pressure oxidation mill is under construction to treat sulphide gold ores in the main deposit. The Getchell gold deposit occurs in a wide fault zone in carbonaceous, calcareous sediments and intrusive rocks. Intense clay alteration is typical within the mineralized zones. Silicification is a less dominant alteration phase within the ore. Gold in the upper oxide portion of the deposit occurs both in a free state which is leachable and complexed in fine disseminated pyrite which is not leachable. Gold in the lower sulphide portion of the deposit is almost entirely complexed in pyrite. Abundant arsenic sulphides and variable amounts of remobilized carbon are associated with the gold mineralization throughout the deposit. The waste dump material being heap leached was derived from the upper portions of the gold deposit. The dumps contain high quantitites of fines, clays and sulphides of iron, arsenic and other trace elements. No stockpiling of low grade materials was attempted during the old mining operations, therefore, the dump material is highly variable and unpredictable. A sample of representative material from one dump contained the following:

Jan 1, 1998

By John P. Norton

Microcystaline silica has been mined in Illinois from the Clear Creek formation since the turn of the century, especially in the area around Tamms in Alexander County, in the southernmost part of the state. Production of this silica, consumed mainly by the abrasives and coatings industries but also sought after for many filler/extender uses, has grown with the economy with several new applications overshadowing traditional markets in recent years. Such an important commodity was given the early attention of the Illinois State Geological Survey and a very complete report was issued in 1953 (Report of Investigations No. 166), authored by J. E. Lamar. The mining and processing of the silica ore has changed very little since the first reported production in 1906, although emphasis has been placed on the production of the finer sized grades to meet newer market requirements. Industrial Mineral Notes 40, published by the Illinois State Geological Survey in June 1970, describes a method by which a less than 1-micron fraction could be commercially produced from the readily available finest commercial grade presently being marketed (99% minus 10 microns). The finer grades exhibit to a lesser degree the reinforcement, high flatting efficiency, thickening and dry brightness properties associated with the synthetically produced silicas. It is expected that the extremely fine grades of microcrystaline silica will become accepted in the markets that now use a combination of precipitated silica and less expensive extender/filler minerals such as kaolin or calcium carbonate.

Jan 1, 1976

By C. A. Pickles, D. Mallette

Silicon nitride (Si3N4 ) is an advanced structural ceramic materia1 which is presently being considered for a number of potential engineering applications, particularly in heat engines, gas turbines, and electronics. With respect to other structural ceramics, silicon nitride has relatively low thermal conductivity and thermal expansion coefficients and a moderate elastic modulus. Thus, during thermal cycling the stresses developed in this material are lower than in other structural ceramics. At the present time silicon nitride is produced via three main processes: thermal decomposition of silicon imide or amide, treatment of silicon tetrachloride or silane vapour with ammonia and nitriding of silicon powder. These three methods of production are discussed with particular attention to the effect of morphology and phase content on the properties of the final product. In this work carbothermal production of silicon nitride has been studied in a high temperature resistance furnace. Compacted briquettes of silica and carbon were produced which were reacted in a nitrogen atmosphere. The optimum reaction temperature and the carbon to silica ratio were found to be 1425OC and ten to one, respectively. The presence of large amounts of ash in the reductant promoted the formation of silicon nitride. The specific surface area of the briquettes did not have a large effect over the range studied in the present work. Briquette seeding with small amounts of Si3N4 was effective in increasing the reaction rates.

Jan 1, 1990

By Jane Morrison

Permanent magnets are used in most electromechanical and electronic devices to convert electrical to mechanical energy and vice versa. More than fifty are commonly found in the average American home and car. A new species of permanent magnet composed of iron, neodymium, and boron has recently been developed which combines superior magnetic properties with compact size. The reduced size of the magnets has enabled significant new developments in such areas as robotics and consumer electronic, among others. The objective of the present work is to efficiently and economically separate valuable rare earth materials from the relatively worthless iron constituent in NdFeB magnet scrap. Several magnet producers have expressed interest in the development of such a process and have provided information and scrap samples to aid in research. Scrap is generated in a variety of forms from different stages in the processing stream. Pieces of magnetic and non-magnetic metal as well as sludge and ribbon from jet casting must all be treated. Beneficiation techniques have been studied and size distributions developed for the different scrap types. Slag from the casting process is resistant to crushing and may need to be embrittled first, but all other types are amenable to crushing and ball mill grinding using stainless steel balls and water. Tabling was found to be useful in classification of magnet sludge. Two major techniques for separation of rare earths have been studied:

Jan 1, 1990

By Victor F. Hollister

The great increase in post-World War I1 use of molybdenum was made possible by discoveries of that metal in porphyry molybdenum and porphyry copper deposits. This section documents significant porphyry molybdenum discoveries of the post-war period. The most important discovery was Henderson in Colorado. It is not only one of the world's largest and richest, but it was found by a team of geologists who defined the hood model and tested it successfully at Henderson. Under the leadership of Stewart Wallace, these scientists established a set of criteria for exploration for Henderson-type de- posits that was copied by the industry. The discovery bf vertical cylinder type porphyry molybdenum deposits was less renowned. Boss Mountain in British Columbia and then Mt. Pleasant in New Brunswick were given relatively scant notice, compared with the Henderson discovery. However, these deposits have geometrics distinct from that found in the typical hood, which directly affects their exploration characteristics. Mt. Pleasant, included in this section, is a well defined, near vertical breccia pipe. Both the Henderson and Mt. Pleasant discoveries were made by relatively small groups operating independently of the bureaucracy that characterizes large corporations. The management role in each case was one of encouragement. In addition, Wallace had the beneficial experience of working for Climax, whose objective was the discovery of porphyry molybdenum deposits. Henderson was the natural outgrowth of the exploration effort by those who studied and understood the Climax deposit.

Jan 1, 1991

By W. de Moura, R. Fueyo, M. M. Botz, J. C. Scola

The Cerro Vanguardia mine is an AngloGold Limited operation in southern Argentina that includes multiple open pits and a hybrid Merrill-Crowe and CIL circuit to recover gold and silver from oxide ore. Operations were commissioned at the site in 1998, which included a plant in the metallurgical circuit to recover cyanide from mill tailings. The cyanide recovery plant was initially configured to process tailings slurry and achieved greater than 90% cyanide recovery from tailings containing about 600 to 800 mg/L WAD cyanide (as CN). The cyanide recovery circuit was operated in this manner for approximately eight months, during which time the consumption of sulphuric acid and sodium hydroxide was relatively high, leading to high rates of scale formation in the acidification tank and stripping towers. In July 1999, several piping changes were made in the cyanide recovery system to permit its operation with clear solution, which reduced the sulphuric acid consumption and eliminated scale formation in process equipment. The cyanide recovery system currently operates with a two-stage counter-current decantation (CCD) circuit which provides clear solution for processing in the cyanide recovery plant. The cyanide recovery efficiency now averages about 90% to 92% from solution containing about 350 mg/L WAD cyanide (as CN). Recovered sodium cyanide now accounts for about two-thirds of the total cyanide added to the leaching circuit. This paper presents a description of the cyanide recovery plant and details regarding its current operating efficiency.

Jan 1, 2004

By William C. Paschen

Damen Avenue to Roosevelt Road, the Tunnel and Reservoir Plan (TARP), a Deep Tunnel Project for the Metropolitan Sanitary District of Greater Chicago consists of 25,189 lin. ft. of 32 ft. tunnel with 1 ft. 0 in. concrete liner throughout. The 17,100 ft. main tunnel connects at both ends with two other Deep Tunnel contracts. A branch tunnel connecting to the mainstream tunnel, commences approximately 4,140 ft. from the construction shaft and runs 8,089 ft. south and terminates at the Racine Avenue Pumping Station. Shaft work consists of one 28 ft. 6 in. diameter construction shaft, one 3 ft. 6 in. diameter access shaft and 25 drop shafts-four of which have vent shafts. The drop shafts vary in diameter from 4 ft. 0 in. to 17 ft. 0 in. All shafts vary in depth to invert from 225 ft. to 235 ft. Work has been underway for 16 months and as of this writing the construction shaft and access shaft are complete. Seven shafts have been excavated and concreting operations have started in four of them. The starter tunnel is complete, the mining machine has mined 250 lin. ft. and the muck removal system is in full operation. The contractor for the project is a joint venture of Paschen/Morrison-Knudsen/Kenny. Paschen Contractors, Inc., Chicago, Illinois is the sponsor. The total contract amount is $107,837,300.00.

Jan 1, 1979

By Thomas R. Kuesel

In traditional construction contracting practice, the owner allocated almost all risks to the contractor, saying in effect, "you deal with all construction problems and all third parties, and don't bother me." In this same tradition, the architect or engineer designed a structure in its finished condition, and if he thought about the construction problems that might be involved in building it, he was careful not to express any opinions on these matters in the contract documents. This feudal attitude fostered two results: 1. Contractors added high contingencies to their bids to cover the costs of risks. 2. Litigation of construction contract claims blossomed. Broadly, the owners lost--the courts reallocated many risks the owners thought they had laid on the contractor. Thoughtful owners and engineers recognized that owners were paying for risks twice --once in bid contingencies and a second time in court. Meanwhile, contractors were not getting rich; they were losing money on delays and disputes, and just about getting even (if they were lucky) in court. And construction law was becoming an increasingly lucrative field--for lawyers. Furthermore, with the growing influx of lawyers onto the construction scene, the owner-contractor-engineer relationship became increasingly an adversary one. The emphasis came to be on culpability rather than capability--who could be held responsible for breaching some contract clause, not who might find a solution to some common problem. This game was played with equal vigor by owners and contractors.

Jan 1, 1979

By Harold G. Arthur

INTRODUCTION Stillwater Tunnel construction is scheduled to start in the spring of 1973. The tunnel will be the site of an extensive program in rapid excavation research. This paper presents a progress report regarding our plans and relates the tentative decisions which have been made on how to carry out the research effort. The details are subject to revision as more input is obtained from other Government agencies interested in tunnel construction and from experts in industry and educational institutions. The objective of the research program is to bring about faster, less costly tunnel construction. This objective will be pursued through the development, improvement, and evaluation of various construction systems and investigative techniques. The need for this kind of program was recognized by the National Research Council, in its authoritative report "Rapid Excavation - Significance, Needs, Opportunities." (1) The Council advocated a federally funded $200 million, 10-year program to help meet the $69 billion market it expects in underground excavation between 1970 and 1990. The significance of tunnel construction to Reclamation is made clear by statistics of its tunneling experience and outlook. Reclamation has constructed 174 water conveyance tunnels totaling over 190 miles, Six tunnels are presently under construction which have a combined length of about 27 miles. There are on the books nine authorized, but unfunded tunnel projects totaling another 70 miles in length. Many more miles of tunnels are included in programs in various stages of investigation.

Jan 1, 1997

By Harold Wagner, Prakash Donde, Larry H. Heflin

INTRODUCTION The Washington Metropolitan Area Transit Authority is responsible for the planned 166 kilometer (103 mile) Metro rapid rail transit system in Washington, D.C. Some 117 kilometers (72.8 miles) of this system is in operation and contains 30.6 route-kilometers (19 miles) of rock tunneling. To complete the planned system an additional 1.6 kilometers (1.0 miles) of single track tunnels in rock are planned and additional contracts will consist of 4 kilometers (2.5 miles) of twin tunnel, resulting in 8 additional linear kilometers (5 miles) of single track tunnel contracts yet to be offered in soft ground. Three recent contracts in soft ground included the New Austrian Tunneling Method (NATM), along with conventional tunneling, as a bid option. Section E5a, Fort Totten Station and Tunnels, was the only one of the three to be constructed using the NATM option. This is the first application of the New Austrian Tunneling Method in soft ground in the United States. This paper will concentrate on the Fort Totten Station chamber NATM design, construction, and the instrumentation readings and evaluations which lead to an engineering back analysis which allowed a refinement of the bid design, resulting in a faster, more efficient construction. Design of the Fort Totten Station and Lines was done by Sheladia Associates. The design team included Greiner Engineering and Jenny Engineering with Mayreder-Consult of Austria, who was responsible for NATM design and NATM construction consultation.

Jan 1, 1991

By John C. Cook

In reasonably dry rock, long-wave radar can theoretically explore to distances approaching 75 meters (250 ft). High-resolution radar reflections have already been demonstrated through 13 m of hard limestone, through 9 to 18 m of coal in place and through 225 m of rock salt, using only low-power experimental radar equipment. Radar reflections have been received through the rock from rough pillar walls, from faults, and from a slim, uncased, vertical drill hole. In three years of intermittent experimentation, the feasibility of rapid radar exploration of large volumes of rock, with portable equipment, in deep, wet workings has been demonstrated. With future, improved equipment the theoretical working range, of the order of 75m, is expected to be attained in most hard rocks. THE TECHNIQUE Fig. 1 illustrates an early "monocycle" radar system (1) set up in a coal mine. This radar equipment is entirely different from that employed for detecting distant objects through the atmosphere. However, the basic principle is the same: a pulse of electromagnetic energy is radiated by the transmitter, a portion is reflected by some "target" object embedded in the surrounding medium and some of this energy is collected by the receiving antenna. In the receiver, the pulse is amplified, is "stretched out in time" by a sampling process, and is displayed on the screen of a cathode-ray oscilloscope. It may also be recorded on paper or magnetic tape. Fig. 2 illustrates a

Jan 1, 1997