Search Documents

By B. C. Cornilsen, X. Shan, D. H. Carlson, J. H. Johnson

Airborne respirable Diesel Particulate (DP) presents an additional health hazard in that it has been shown to be mutagenic. This problem is of increasing concern as more coal mines introduce diesel vehicles. If the DP present in coal mine air is to be controlled it must first be measured. This paper describes development of the laser Raman spectroscopic measurement of the amount of DP in DP/coal mixtures collected on filters in the laboratory and in coal mines. The Raman technique provides a chemical measure of the carbonaceous material in each component, and is not dependent upon particle size. When this work was begun there were no known analytical methods for this measurement. Side-by-side in-mine comparisons of the results obtained from Raman, neutron activation analysis, and size selective analyses (MOUDI and personal samplers) are presented. The neutron activation and size selective analyses were obtained by the USBM Twin Cities Research Center and University of Minnesota. Good agreement has been found among these three methods.

Jan 1, 1991

By G. A. Doyle

Until the suspension of conventional operations in 1996, the White Pine Mine was the second-largest active underground copper mine in the United States, underlying an area of approximately 30 km2 (13 sq. miles) in the Upper Peninsula of Michigan. The mine operator intends to initiate in-stope solution copper mining by circulating a solution (lixiviant) of mine water, sulfuric acid and ferric iron through rubblized ore. As planned, the solution would be retired in the mined-out stopes following completion of the solution-mining activities. Investigations into the fate of the retired solution indicated that the solution, through time, would change from an acidic, metal-rich solution to a near-neutral, reducing solution containing much lower concentrations of metals. Investigations included reaction-path modeling (EQ3/6) and laboratory and in-mine tests. The combination of neutralization and reduction will result in precipitation of most metals, primarily as metallic sulfates, chlorides and sulfides.

Jan 1, 1997

By K. A. Natarajan, J. M. Modak, P. Anand

A microbial survey of Jamnagar bauxite mines in Gujarat, India, revealed the indigenous presence of a variety of autotrophic and heterotrophic bacteria and fungi associated with the ore body and water ponds in the vicinity. Among these, bacteria belonging to the genera Thiobacillus, Bacillus and Pseudomonas are implicated in the weathering of aluminosilicates; the precipitation of iron oxyhydroxides; the dissolution and conversion of alkaline metal species; and the formation of alumina, silica and calcite minerals. Fungi belonging to the genus Cladosporium can reduce ferric iron and dissolve alumina silicates. Biogenesis thus plays a significant role in bauxite mineralization. Various types of bacteria and fungi, such as Bacillus polymyxa, Bacillus coagulans and Aspergillus niger, were found to be efficient in significant calcium solubilization and partial iron removal from bauxite ore. Probable mechanisms in the biobeneficiation process are analyzed. Biobeneficiation is shown to be an effective technique for the removal of iron and calcium from bauxite ores for use in refractories and ceramics.

Jan 1, 1998

By Gail I. Bakker, Mark E. Smith, George Sintay, Allan Young

The Snow Caps mine was an open pit and conventional cyanide heap leach gold project located 10 Km east of Independence, California in the Owens Valley. The project is unique in that it is one of the first projects to go full-cycle, from design through closure, under California's Chapter 15 mine waste regulations adopted in 1984. The property was acquired by Sunshine Mining Company in 1985. During 1986, final design and permitting were completed and the facility was commissioned in 1987. Mining continued to mid - 1990, when the minable ore body was depleted, and heap leaching continued into early 1991. Rinsing of the spent ore was completed in 1991, and final closure will be complete in 1992. The spent ore will be left on the leach pad for its final disposition. The focus of this paper is the permitting and closure aspects of the project as required by California's Chapter 15, Article 7 regulations.

Jan 1, 1992

By Terry I. Mudder, Michael M. Botz

In general, the cyanidation of silver ores requires higher con­centrations of cyanide in comparison to gold ores to affect simi­lar leaching rates and metal recoveries. The requirement for high cyanide concentrations in a silver ore leaching circuit may translate into higher operating costs, however with operation of an acidification-volatilization-reabsorption (AVR) plant to recover and recycle tailings cyanide, cyanide consumptions can be significantly reduced. At each of the currently operating AVR plants in the world, overall cyanide consumptions have been reduced by approximately one-half by recovering and recycling tailings cyanide. In addition, the AVR plants have reduced tail­ings cyanide concentrations to less than 20 to 30 mg/L WAD cyanide and reduced potential adverse impacts to wildlife in the tailings impoundments. This paper presents an analysis of the application of A YR to a silver ore leaching operation which has a CCD/Merrill-Crowe circuit included in the metallurgical plant.

Jan 1, 1998

By Keith Sarbutt, I. Jackman

The recovery of gold from a high grade telluride/sulphide flotation concentrate was investigated. Conventional cyanidation resulted in very slow rates of gold extraction. Historically, the refractory nature of tellurides has been overcome by fine grinding, the use of excess lime and long leach times. In some instances, pre­oxidation of the tellurides has also been necessary, to render the gold soluble in cyanide solutions. The former conditions did improve the rate of gold extraction from the present sample, but final recovery was still unacceptable. Chemical oxidation of the tellurides and leaching with oxygen improved gold recovery further. However, it was found that simple modifications to the cyanidation conditions overcame the detrimental effects of the complex chemistry involved in leaching a telluride concentrate. The incorporation of a solution change, or the application of a carbon-in-leach procedure increased the recovery of gold to over 97 percent in 96 hours. In every case, leaching was enhanced by the addition of lead salts.

Jan 1, 1990

By Brendan Parker, Joseph Skrypniuk

Boddington Gold Mine1 (BGM) commenced production in 1987 and is currently ranked as the second largest gold producer in Australia. In a strategy to improve plant efficiency, constraints to plant performance were identified and prioritised with a view to maximising benefit for minimal expenditure. After identifying that leach kinetics and circuit residence time were major constraints, the introduction of oxygen was identified as having the greatest potential for the delivery of sig­nificant cost benefits. The application of oxygen, initially by conventional tech­niques, and subsequently by installation of Atomaer's Filblast gas shear reactor, improved gold recovery, reduced the resi­dence time constraint and enabled higher mill throughput to be achieved. Additional benefits included operation at lower pulp densities and a reduction in reagent usage. A significant reduc­tion in unit operating cost resulted from these benefits. This paper quantifies the above benefits in a format accept­able to both metallurgists and accountants by integrating the findings in a techno-economic perspective.

Jan 1, 1996

By Antonio Dominguez-Perez, Annette Dickmann, Roy Norcross, Andreas Rubo, Stephen Gos

With increasing cost pressure in the production costs of gold, there have been great efforts made to reduce the gold production costs as much as possible and a great deal of effort and lateral thinking is required to maintain a cost effective gold production facility. In a difficult economic environment, there is always the danger of saving in the wrong place. Just like it can be fatal to cut down on innovative research and development for long-term existence and sustainability in most industries, savings in safety and visionary planning of regulations expected in the future can become very costly on the long run, if preventative measures are not taken, observed or ignored. This paper deals with some current topics pertinent to the gold mining industry with regard to the interaction between potential risks, regulations and the costs that arise and can be saved in relation to these. Only an optimal combination of cost effective, safe and technically feasible regulations enable an operation to work economically.

Jan 1, 1999

By J. Kulczycka

Poland in time of transition had been dealing with the remnants of the previous regime ? particularly in the field of environmental protection. The burden left was tremendous and there was a need for fast and effective tools for improving the environment. The idea of environmental protection had been supported by the introduction of a new environmental policy that underlined the importance of sustainable development in industry in the beginning of 1990s. This policy introduced high environmental fees and fines ? a concept not very popular in Europe in that time ? and good only for a country in transition to boost the protection of the environment. While this policy had its role to play, its role is now completed. It is time to move forward, especially when these environmental charges affect the international competitiveness of industries so much, and at the same time have virtually no influence on environmental protection investments any more.

Jan 1, 2005

By L. A. Arrington-Webb

Forty-four states produced clay products during 1994 for a total value of $1.6 billion. This was a 3% increase in total tonnage and a 7% increase in value from 1993. Kaolin Domestic production of kaolin during 1994 was estimated to be 9.3 Mt (10.2 million st), according to the US Bureau of Mines (USBM). Georgia remained the leading producer with 7.5 Mt (8.2 million st), followed by South Carolina with 535 kt (589,000 st). Kaolin used as a paper coating or filler pigment accounted for 51% of domestic consumption. Other uses included grogs (14%), fiberglass (5%) and plastics (4%). A reclassification by an Alabama producer of fire clay to kaolin accounts for the introduction of kaolin used in grogs. This also accounts for the apparent decrease in the use of kaolin in paper from 60% in 1993. However, the actual amount of kaolin used in paper was the same.

Jan 1, 1995

By T. Naarttijärvi

The Fabian ore body near Malmberget, Sweden, has an ore reserve of 5 Mt of predominately low grade iron ore, containing 40-55% Fe. Mining began in 1971 with a new method called slot block caving. About 2 Mt were mined, but poor fragmentation resulted in too much secondary blasting. This decreased mucking efficiency to such an extent that the method was abandoned after only 40% of the ore volume had been mined. At this stage a large stope (180 x 30 x 100 m) had been excavated. Although the exposed area was quite large, no caving action occurred in the hanging wall or in the ceiling. LKAB decided in 1977 to introduce sublevel stoping using 105-mm-diam holes. This was the first time large diameter holes were used underground in Sweden. The method had been evaluated in collaboration with the University of Luleå (LuH), the Swedish Detonic Research Foundation (SveDeFo), and the Swedish Mining Research Foundation.

Jan 3, 1982

By M. A. Cocquerel

INTRODUCTION Davy McKee have developed and patented a combined mixer settler (CMS) which has undergone extensive trials and has now been installed in two commercial uranium plants in South Africa. Substantial capital and operating cost savings can be realized over conventional mixer settler in uranium extraction, especially from dilute feedstocks containing approximately 200 ppm U308. Pilot plant work has also been undertaken on other metal extraction systems and the results are very encouraging in most areas of interest. CONVENTIONAL MIXER SETTLERS The conventional plant in use at many uranium recovery facilities consists typically of a mixer box in which the aqueous and organic phases are contacted and a settler in which the two phases separate. The mixer box must allow sufficient residence time for the mass transfer kinetics to be satisfied for the particular species involved. The settlers are usually rectangular and take the form of shallow tanks of large cross sectional area.

Jan 1, 1984

By Michael R. Smith

Barrick Goldstrike Mines Inc.’s Betze open pit is located at the north end of the Carlin Trend, in Eureka County, NV. Ten open pit gold mines exist on the trend, which strikes northwesterly, through the north end of Eureka County and into Elko County (Fig. 1). The final pit will be about 2440 m long x 1550 m wide (8000 x 5100 ft), elongate in a west-northwesterly direction and about 425 m (1400 ft) deep. The pit straddles the Barrick-Newmont Gold Co. property boundary. History The first hole at the Goldstrike Mine was drilled in 1962. Between 1963 and 1964, 17 shallow holes were drilled with little encouragement, in view of the price of gold at $1.12/g ($35/oz). From 1962 to 1975, several different companies explored the Goldstrike property. In 1975, Pancana Industries acquired the property. In 1976, Pancana’s exploration efforts found sufficient gold mineralization to initiate heap leach production. In 1977, Pancana formed a joint

Jan 1, 1994

By Raymond S. Shrode

Limestone and dolomite production is of significant importance to the Baltimore and Ohio Railroad. Except for coal, more tons of limestone and dolomite are moved by the Railroad than any other mineral raw material. In the territory served by the Railroad, these materials are produced from every geologic system from Cambrian through Pennsylvanian. Some of the operations produce premium stone acceptable for high-specification steel and chemical use; at others, the stone finds application as aggregate materials and for cement manufacture. The Railroad is interested in seeing continued production from the operations it now serves, and in serving operations in a way mutually beneficial to the Railroad and to the producer. In working with producers, the importance of geologic knowledge in prospecting and development of deposits has been clearly recognized. In turn, knowledge of the economic and technological facets of production and consumption is needed for the geologists to participate with maximum efficiency.

Jan 1, 1966

By D. D. Runnells, D. C. Keith, G. A. Doyle, J. Tilk

Until the suspension of conventional operations in 1996, the White Pine Mine was the second-largest active underground copper mine in the United States, underlying an area of approximately 30 km2 (13 sq. miles) in the Upper Peninsula of Michigan. The mine operator intends to initiate in-stope solution copper mining by circulating a solution (lixiviant) of mine water, sulfuric acid and ferric iron through rubblized ore. As planned, the solution would be retired in the mined-out stopes following completion of the solution-mining activities. Investigations into the fate of the retired solution indicated that the solution, through time, would change from an acidic, metal-rich solution to a near-neutral, reducing solution containing much lower concentrations of metals. Investigations included reaction-path modeling (EQ3/6) and laboratory and in-mine tests. The combination of neutralization and reduction will result in precipitation of most metals, primarily as metallic sulfates, chlorides and sulfides.

Jan 1, 1998

By H. Sis, S. Chander

The beneficial effect of a series nonylphenol polyethylene glycol ether surfactants were tested in the flotation of phosphate ores in which the mixture of sodium oleate and dodecane was used as collector. The performance of nonionic surfactants was first tested in the microflotation of pure apatite mineral. Microflotation experiments showed that the recovery of apatite depends on the number of ethoxylation of the nonylphenol surfactants and decreased with higher ethoxylation. The nonionic surfactant with the smallest ethoxylation group used in this research (NP-4) was then tested in batch flotation of phosphate ores. The flotation of three different size phosphate ores was carried out in the absence and presence of NP-4 surfactant. The beneficial effect of nonionic surfactant was obtained for fine size (-35+150 mesh) and very fine size (-150+400 mesh) phosphate ores at different collector dosages studied. But, in the flotation of coarse size (-16+ 35 mesh) phosphate ore the beneficial effect of nonionic surfactant was obtained only at high collector dosages.

Jan 1, 2002

By Peter Sullivan, Johan van Heerden

Increased use of continuous miners and roadheaders in the underground coal mining industry in South Africa has led to improved productivity and efficiency of operations. Of major concern, however, is the increased amount of airborne dust generated during mining. Dust is a health hazard in terms of respiratory diseases, can impede productivity and is the major contributor to the potential of underground explosions. The concern of the South African coal mining industry with regard to the underground dust problem has led to the establishment of a Dust Control Section in the Coal Mining Division of COMRO. In the field of dust suppression system evaluation and design, collaborative work has been undertaken by COMRO and FLOSEP. This paper gives a review of the application of Computational Fluid Dynamics (CFD) in evaluating and improving environmental conditions in continuous miner and roadheader sections. A brief history of the development of the CFD model as well as a discussion of a typical application is included.

Jan 1, 1993

By D. R. Nagaraj

Literally thousands of new flotation agents, both collectors and modifiers, have been proposed for sulfide and non-sulfide flotation over the past six decades since the beginning of the use of soluble surfactants in flotation. In stark contrast, the number of flotation agents used in practice is small. Xanthates and fatly acids, along with a few well-recognized modifiers, dominate the industry. Three major questions will then arise: a) are there truly specific needs in the industry that call for chemistries that are different from those used currently ? b) if yes, given the track record in the industry, what is the likelihood that such different chemistries will ever be used and to what extent ? and c) is more research into developing new chemistries necessary ? A critical assessment of flotation agents in general is made in this paper to provide answers to these questions and to identify the major factors that are responsible for the large disparity that exists between flotation reagent research and commercial usage.

Jan 1, 1994

By F. G. Miller, M. Polat, S. Chander

Flotation was used to achieve improved separation of magnetite from the float and sink products obtained from heavy medium separation and to reduce the load of the medium cleaning circuit. The investigation was carried out in two successive phases. In the first phase, tests were performed on in-plant samples from the Homer City Coal Perdition plant to determine what effects variables such as medium density, particle size and magnetite source had on the efficiency of the process. In the second phase, the optimum conditions determined in the first phase were used to determine the applicability of the process to other selected coals from central Pennsylvania. It was observed that flotation was very effective in the separation of magnetite from coal. In most of the cases investigated, the magnetite recovery was approximately 99% with a magnetite grade ranging from 95 to 99%. The grade of the magnetite decreased as the ash content of the coal increased and the particle size of the magnetite decreased.

Jan 1, 1994

By Sukumar Bandopadhyay

In recent years planning of surface mines in general and reclamation and post-mining land uses in particular have become very complex. Due to the lack of suitable techniques, land use plans are rarely based upon structured decisions. Data collection may be conducted in a rigorous manner and certain analyses may be performed on the data; the decision to put the land to a specific use, however, is finally based upon the intuitive judgment of one or several individuals. This paper demonstrates how techniques from fuzzy set theory can be used in order to select an optimum post-mining land use plan. The various land use planning alternatives have been characterized according to both qualitative information and quantitative factors and the "fuzzy" aspects of the collected information are incorporated into the analyses. In a practical application, the methodology is used to obtain the most reasonable solution to a post-mining land use planning problem in Interior Alaska.

Jan 1, 1986