Search Documents

By B. C. B. Pretorius

A heat load analysis of the very hot sub-shaft area of Loraine gold mine situated near Welkom, South Africa, showed. that the heat that needed to be removed to give acceptable wet-bulb temperatures at the working faces could not be done by the normal ventilation air alone, but would have to be complemented with extensive refrigeration. The paper outlines the considerations in selecting the cooling system adopted for this shaft.

Jan 1, 1980

By Rory P. A. Ball, Mark Briggs, Martin Dix

"Tunnel professionals should inform project stakeholders on the reality that tunnel projects are not 100 percent devoid of the need for excavations or public inconveniences during both design and construction phases. Competing stakeholder objectives to limit these disruptions must be weighed against the need to mitigate risks and to produce a constructible, operable and maintainable end product. Perhaps the approach we should take with stakeholders, also known as Authorities Having Jurisdiction (AHJs), is sharing memorable case studies that bring to life the potential risks so often buried within lengthy risk registers. This paper provides a sobering case study describing what can occur if the presence and/or location of utilities and other obstructions are not fully understood due to restrictions placed on exploration or mining operations. In this instance, the Microtunnel Tunnel Boring Machine (MTBM) encountered a buried concrete structure, followed by rows of abandoned wood piles, before finally colliding with an active high-pressure gas main under a bustling coastal highway. Multiple stakeholders imposed tight logistical and other work restrictions, compounding the difficulties experienced during the drive. However, the difficulties were effectively managed through the project team’s proactive collaboration and communication with everyone involved. INTRODUCTION Some of the most important decisions that influence the ultimate success or failure of a project may not be made by design engineers. Instead, these decisions are often made by project stakeholders and third-party agencies. Tasked with protecting the best interests of their users, these agencies are cautious of potential impacts associated with project construction and subsequent use. Unfortunately, actions required (or restricted) by stakeholders often result in unwanted ripple effects that negatively affect the very users they are trying to protect. For example, a mandate limiting a shaft site to an unreasonable size may be intended to reduce local business impacts, but may actually increase impacts as more supply and truck hauling is required."

Jan 1, 2016

By Raúl Castro, Marco Vera, Alfonso Ovalle

The underground mining evolution for block cave mines in Chile and worldwide has made important strides in the last decades. Nonetheless, reserves determination in the initial stages of these types of projects—mainly for long-term planning—is not studied in as much detail as it should be, especially regarding the impact on the final value of the enterprise. Today, the first estimation of the size of a block cave mine, typically expressed in tons, tends to determine very large footprints and ore bodies. The resulting large-scale mine is obtained by applying the marginal cut-off grade (COG) to determine reserves. Yet, in many cases, it is possible to obtain an equal or higher benefit, extracting fewer reserves in less time, with a smaller active area, which significantly reduces the project’s uncertainty. To explore scenarios obtained by applying a higher marginal COG in the initial phases of the project, the Hill of Value methodology is used to estimate the net present value (NPV) in relation to the production rate and the COG. However, the application of this methodology considers certain simplifications that generate results which are not completely satisfactory in specific cases. This paper suggests an improvement of this method to obtain more reliable results regarding determination of a COG profile that will optimize the NPVof a block-cave project. The methodology was developed and applied in a massive polymetallic deposit with zinc, lead, and silver mineralization, corresponding to a real block caving project. The methodology provides NPV results that differ by approximately 15% in comparison to the real mine plan, while also being considerably simpler and faster to calculate. In summary, the proposed methodology provides a reasonable and fast procedure to estimate higher than marginal COG that increases the NPV of block cave mine projects.

By A. Cecala, J. Noll, J. Hummer

"NIOSH has observed that many control rooms and operator compartments in the US mining industry do not have filtration systems capable of maintaining low dust concentrations in these areas. In this study at a mineral processing plant, to reduce respirable dust concentrations in a control room which had no cleaning system for intake air, a filtration/pressurization system originally designed for enclosed cabs was modified and installed. Eighty-seven percent of submicron particles were reduced by the system at static conditions, meaning that greater than eighty-seven percent of respirable dust particles should be reduced. The particle size distribution for respirable dust particles are greater than for submicron particles, and filtration systems usually are more efficient in capturing the larger particles. A positive pressure near 0.02 inches of water gauge was produced which is an important component for an effective system and minimizes particles (e.g. dust) from entering into the room. The intake airflow was around 118 cfm, which is greater than the airflow suggested by ASHRAE for acceptable indoor air quality. INTRODUCTION Chronic overexposure to respirable silica dust (particle diameter < 10 microns) leads to a progressive lung disease known as silicosis. Workers who develop silicosis have an increased incidence of lung cancer and pulmonary disorders. In June 1997, the International Agency for Research on Cancer (1) found sufficient evidence to declare that inhaled crystalline silica in the form of quartz and cristobalite is carcinogenic. Mining is one of the leading industries for occupational exposure to silica dust (2-7). Control rooms located in dusty areas in some mines are of particular concern (8). Many mineral processing operations utilize operator’s compartments and/or control rooms to house workers who are performing particular job functions. Most industrial processing mills have rooms where a worker looks out over the facility and has direct control over the product flow throughout the entire building. In addition, primary crusher operators are often located in a compartment from which they are able to view the primary crushing function. Their job is to control when trucks dump into the primary jaw crusher and the rate of feed of the ore from the hopper into the crusher. Many of these control rooms and operator booths do not have filtration systems capable of cleaning air entering the control room or booth, which can result in elevated concentrations of dust in the room or booth. To reduce the dust concentrations in these rooms, it would make sense to clean the entering air with filtration/pressurization units similar to those proven to provide a clean environment in enclosed cabs."

Jan 1, 2016

By A. E. Halim, J. F. Brune

The 2006 Sago, Darby, and Aracoma mine disasters in the United States (US) forced the US government to implement the 2006 MINER Act and additional regulations that require all US underground coal mines to install and maintain refuge chambers to manage entrapment emergencies, in particular, fires and explosions. However, there is a debate on whether barricading in refuge chambers is a good strategy to survive such emergencies. Australian coal mines are not required to use refuge chambers and, instead, have adopted a strategy that focuses on instructing and training miners to self-escape to the surface. This paper analyzes merits and problems of using refuge chambers and self-escape to the surface to manage emergencies in fires or explosions in an underground coal mine. The authors found that the use of refuge chambers may not be the best strategy during extensive fires or when multiple explosions happen. In these situations, mine rescuers are unlikely able to extract miners who are sheltered in chambers and conversely, self-escape may save more lives than sheltering. Chances for successful self-escape are further improved by regular, externally assessed training such as Level 1 Emergency Exercises required in the Australian State of Queensland. These exercises put pressure on mine operators to ensure and maintain the effectiveness of their emergency management system.

By J. W. Leonard

Breakage, handling and treatment techniques that result in the placement of greater quantities of coal in fixed volume haulage units such as ships, railroad cars, trucks, mine cars, shuttle cars and scoops can do much to increase productivity by improving bulk density to reduce delivered cost, surprisingly enough, only in steel industry by-product coking has this subject been investigated and applied to practice, where as much as 20% or more productivity has been achieved. Research at UK Mining using popular coal mine loading cycle simulators shows that for typical Central Appalachian mining conditions a 10 to 20 percent gain in bulk density can produce a 15 to 30 percent increase in the loading cycle time of fixed volume shuttle-car/scoop based mining systems.

Jan 1, 1989

By M. E. Buzon, M. E. Gunter, B. D. McNamee

A Google search on talc asbestos yields more than 500,000 hits due to the growing number of civil lawsuits in this area. Historically, the litigation was centered on amphibole-containing industrial talc. There was no debate these talcs contained amphiboles, but the issue was the definition of asbestos and whether the amphiboles had an asbestiform habit. Ultramafic-hosted talcs, however, are formed in such a way as to not favor the formation of amphiboles in the talc, but they can occur in the surrounding black-wall. In these deposits, the serpentinite host rock is in direct contact with the talc, therefore, allegations can be made that non-asbestiform amphiboles or non-regulated serpentine group minerals can occur in the final products. We analyzed talcs from both metamorphosed carbonate- and ultramafic-hosted talc deposits using polarized light microscopy (PLM), scanning electron microscopy (SEM) with energy-dispersive spectroscopy (EDS), electron microprobe (EPMA) with wavelengthdispersive spectroscopy (WDS), transmission electron microscopy (TEM) with EDS, and powder X-ray diffraction (XRD). Compositions of minerals determined by EDS alone are not sufficient to confidently identify asbestos, despite common practices by some researchers. We emphasize, using both historical samples, and analyses of currently contested minerals, the importance of determining both the structure and composition of a mineral, as well as defining its morphology, before concluding whether it is asbestos.

Jan 1, 2018

By George A. Desborough, David L. Fey, Stanley E. Church

About 100 mine-waste dumps from past metal exploration and mining in Colorado and Montana were sampled using surficial-sampling methods for laboratory studies of the minus-2-mm fraction. In the laboratory, the composite samples were split into l00g samples that were leached to assess their acid-generation potential and associated release of potentially toxic metals that may degrade water quality in the headwaters of the Animas River watershed in Colorado and the Boulder River watershed in Montana. Two leach methods were studied: a passive leach using de-ionized water, and a more aggressive leach following the EPA-1312 method. The resulting pH values of the leachates using both methods are comparable. The concentrations of sulfate and several, but not all, dissolved or water-soluble metals are higher in the EPA-1312 leachates than in the passive leachates; however, the overall trends of the data are very similar. The passive leach method is less labor intensive and may be more representative of the natural weathering process occurring on the mine-waste dumps, simulating the natural precipitation and snowmelt. Three chemical characteristics of mine wastes studied here provide a relative ranking of mine-waste dumps for the purpose of determining priority for removal or remediation. These characteristics are: net acid production (NAP), sum of dissolved toxic metals (?As+Cd+Cu+Pb+Zn), and dissolved iron in leachates. Ranking can be done evaluating plots of NAP versus the sum of dissolved toxic metals, and NAP versus dissolved iron. These two plots serve as a basis for relative ranking of polymetallic-vein and acid-sulfate mine wastes studied. This ranking scheme may apply to mine wastes from production of other deposit types in other watersheds.

Jan 1, 2000

"?irovski Vrh" Uranium deposit in Slovenia is type of mineralized sediments in ore bearing belts of deflected S-structure, in which the belt is less than 25% mineralized. Ore bodies of irregular small thickness, unreliably contoured, made difficult estimation of correct contours, which are necessary for design and exploitation works. The deposit was explored by vertical boreholes made at the surface and by boreholes fanned from drives. For the purpose of application of this estimation method, 1 m composites have been made in slices which were parallel to the referential belt plane. Estimation was made for 1,5m x 1,5m x lm blocks which do correspond to the size of the containers in the ore transport stage. Two variables have been used: the first, indicator of function (ore=1, waste material =0) and kriging method; the second, logarithmical content of Uranium and Minimum Mean Square Error Estimation (MMSEE) method. Based on estimated values of those variables, probability of ore quantity as well as Uranium content over determined cut-off were calculated for each block. Those two parameters enable determination of the most probable form of the ore body in ecah one metter slice. Estimation of sixteen small blocks in a large 1,5m x 1,5m x 1m block made possible estimation of ore quantity and its content for the determined cut-off, as well as categorization of exploration. This method is being used for estimation of ore reserves and planning of exploration operations. The described&apos; methodology was tested in an exploitation block.

Jan 1, 1986

By Henry G. Healy

Observation well (Hydrographs are shown for these selected wells) Contour represents the height, in feet referred to mean sea level, to which water would have risen in tightly cased wells that penetrate the major water- bearing formations in the Floridan aquifer, July 6-17, 1961. Contour interval 10 and 20 feet, changing at mean sea level. [ ] Extent and distribution of flow areas vary with fluctuations of the piezometric surface, particularly in areas of heavy Relatively small areas of artesian flow are not included immediately adjacent to and paralleling the coast and many of the major rivers and springs

Jan 1, 1966

By Dennis Dolinar

Improperly designed support systems have led to unplanned roof falls in longwall tailgates. To prevent such falls requires appropriate support and adequately designed support systems. The National Institute for Occupational Safety and Health (NIOSH) is currently developing a standing support design methodology based on the ground reaction curve. To design the support system with this methodology requires a quantitative assessment of the ground and support interaction, which is developed from instrumented test sites installed in longwall tailgates. To compliment and expand the field data results and to optimize the support design, numerical modeling is also conducted. The models are calibrated from the test site data. In the present study, data was obtained from a longwall tailgate in the Illinois basin. The test site was located in the Herrin No. 6 coal seam at a depth of 500 ft. At the site, the immediate roof was a weak shale overlain by a competent limestone. Above the limestone, sandstone formed the intermediate roof. The floor consisted of a weak underclay. In the study, the performance and interaction with the surrounding rock mass of two different standing supports, an engineered crib and a conventional 4-point wood crib were monitored. The two cribs have similar load-displacement characteristics at least through 6 in of displacement. Beyond 6 in, the engineered crib becomes unstable and begins to strain soften and shed load. The measurements and developed ground reaction curves indicated that the tailgate at the mine was a low convergence environment until well inby the face. Because the convergence was well below their capacity, both supports provide more than adequate levels of support to the tailgate. Significant convergence and support loading did not occur until 90 to 100 ft inby the face. The results of this study were also compared with results from similar studies conducted in the Pittsburgh seam to further advance the development of the ?ground reaction curve? based support system design.

Jan 1, 2009

By S. Mertikas

The purpose of this paper is to set the stage for (1) the determination of the specifications and actions required for a successful development of a system for the management of waste deposits and contaminants resulting from activities in the mineral industries and landfills and (2) the appropriate infrastructure to be developed at the industrial level. The design of this system would be such that its application could be extended to other industries as well. Waste deposits and contaminants from activities in the mineral industries and landfills commonly cause damage to the environment. In addition to precautionary measures aiming to protect against environmental impact, early warning and immediate response to mining hazards and contaminants is a requirement for sustainable development. Hazard detection and control requires continuous and real-time detection techniques, as well as methods for tracing and predicting the motion of contaminants and waste products. The efficient accomplishment of these goals in the minerals industry requires developing an integrated system for environmental monitoring using remote sensing technologies, in combination with advanced image analysis and geostatistical techniques.

Jan 1, 2003

By M. R. Shahan, W. R. Reed, P. Zhang, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3,000 cfm (1.42 m3/s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts; and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3/s). INTRODUCTION Roof bolting machines are used to drill bolt holes into the roof of an underground mine at specified patterns and to install roof bolts to secure the roof from falling. At times, the roof bolting machine is also used to install rib bolts; however, only the roof bolting operation was considered in this simulation. Though the roof bolting operation drastically improved the safety of miners from roof falls, some roof bolter operators are experiencing health problems associated with respirable dust. Based on recent statistics [1], following a low point in the late 1990s where the prevalence of coal workers’ pneumoconiosis (CWP) in miners with 25 years or more tenure was approximately 5%, CWP now exceeds 10% for miners with 25 years or more of tenure. In central Appalachia (Kentucky, Virginia, West Virginia), 20.6% of long-tenured miners have CWP and 4.5% have progressive massive fibrosis, the most severe form of CWP. CWP, also known as black lung, is an occupational respiratory disease that has no cure and can ultimately be fatal. The only way to prevent the incidence of black lung is to eliminate miners’ exposure to respirable coal mine dust. Current U.S. regulations require that the overall respirable dust concentration to be 1.5 mg/m3 or less for a full-shift sampling if respirable quartz is not present; otherwise, the standard is 10 divided by the percent quartz (not to exceed the 1.5 mg/m3 respirable dust standard) [2, 3].

Jan 1, 2019

By W. S. Fyfe, G. Southam, T. J. Beveridge

Sporosarcina ureae was able to grow in the presence of tip to 10-ppm L-asparagine complexed gold. However, 10 ppm Au3+ was found to be highly toxic to Sporosarcina ureae, killing 109 bacteria/mL within a few seconds. To compare the effects of these responses on gold mobility, an in vitro bacterial biofilm model was developed to examine the interaction be¬tween Sporosarcina ureae and ionic gold or L-asparagine gold complexes in gravity fed columns. The immobilization of ionic gold was between 80% and 90% over a period of one week. But, as the available cellular reactive sites became saturated, immobilization decreased to 14% within two weeks. In the L¬asparagine-gold system, gold immobilization in the cytoplasm occurred at a high rate (80% to 90%) throughout the experi¬ment, with limited toxicity towards Sporosarcina ureae. The bacterial immobilization and detoxification of L-asparagine¬complexed ionic gold was associated with a low molecular weight, i.e, <5,000 dalton (atomic mass unit), intracellular protein fraction. This peptide-complexed gold would allow for the continued biogeochemical cycling of gold under ambient (<100°C) surface or near-surface conditions.

Jan 1, 2000

By Stefan Lorenz, Robert Galler

"The technical lifetime of underground structures does not only depend on the long-term behavior of individual support elements and material characteristics, but also on various boundary conditions, which influence the entire long-term system behavior of the structure. Thanks to the construction of second tunnel tubes and the corresponding cross passages sampling of support materials such as shotcrete, concrete of the inner lining and rock bolts including sheet membranes is possible. To evaluate the stresses and the supporting effects of the tunnel shells, flat-jack tests and different simulations were performed. With these simulations the percentage of the load bearing behavior of the shotcrete shell can be determined. From the results, conclusions for new design approaches for tunnel construction should be generated. New concepts, in which the outer lining is part of the permanent support elements can be considered. This approach would be applicable for conventional as well as mechanical tunneling. INTRODUCTION Tunnels are an indispensable part of modern transport infrastructure. As multi-generation structures their long-term preservation as well as their technical service life is of central importance. The current state of research in the field of durability of structural elements must be considered separately. In almost all areas a prediction of materials and structural components towards lifetime exists. System-wide investigations were rarely performed, so that there is no technical lifetime consideration of the outer lining in systems included. In this study the mechanical behavior of the interface connection in a double shell lining (DSL) tunnel was investigated in laboratory tests. Objective The target of this work is, at first, to create a large database with the lifetime of different structural elements and materials, which may be the basis of durability considerations of tunnels. Secondly, the goal of these investigations is to optimize tunnel designs and their dimensioning regarding to the technical lifetime. For that matter, it is necessary to analyze the selected approaches of the loss of strength and stiffness of the outer lining."

Jan 1, 2016

By Thomas L. Hurst, Joseph M. Hans

INTRODUCTION The former Shiprock uranium mill site is located in the community of Shiprock, New Mexico on a bench overlooking the San Juan River (Figure 1). Both Shiprock and the mill site are located on the Navajo Indian Reservation. The millsite was built on a 230 acre tract leased by Kerr-McGee Oil Industries Inc., and was operated from 1954 to 1963. The Vanadium Corporation of America and its successor, the Foote Mineral Company, operated the mill from 1963 to 1968. During its entire operation, 1.5 million tons of uranium ore was milled producing 3711 tons of U308 concentrate. The concentrate was sold to the former U.S. Atomic Energy Commission. During milling, the ore was crushed to less than 35 mesh and acid leached to remove the uranium. The [ ] uranium was removed from the leach solution by solvent extraction and the uranium-barren solution discharged into raffinate ponds for disposal by evaporation and seepage. The spent solids (tailings) were pulped with waste process fluids and water and discharged to form tailings piles. The piles (ponds or dams) were formed with earth starter dikes. The dike walls were then raised using the separated sand fraction of the tailings. The slime fraction of the tailings were discharged into the diked impoundment. Since only a small fraction (0.25 percent) of the ore was U308 by weight, most of the ore bulk ended up as wastes. The wastes contain nearly all of the uranium decay chain radionuclides present in the ore except uranium. The mill was shut down and partially dismantled before the lease expired in 1973, and the remainder of the mill and wastes reverted back to the Navajo Tribe which was the lessor. Portions of the millsite were then occupied by the Navajo Engineering and Construction Authority (NECA), a Tribal enterprise. In order to provide skilled personnel to operate earth moving equipment, a heavy equipment operator&apos;s training school was also established on the mill site and was administered and operated by NECA. The U.S. Public Health Service (PHS) and the Environmental Protection Agency (EPA) staff conducted radiation surveys at four inactive uranium millsites on the Navajo Reservation in April 1974. During the survey of the Shiprock millsite, it was noted that the training activities were degrading its radiological condition. Both the PHS and EPA staff recommended that the training activities be directed towards the decontamination of the millsite area and interim stabilization of the tailings piles. Preparation for the decontami-nation work commenced in April 1974. In order to facilitate the decontamination activities, the mill site and its contaminated environs were divided into major areas labeled A through F (Figure 2). Areas A, B, and C are defined as "perimeter" areas and contained surface contamination ranging from 5 to 30 cm deep. Area D defined the mill yard and contained contamination ranging from 0.6 to 5.5 m deep. Area E contained several raffinate ponds which were removed to line up the northwest boundary of the tailings pile and to move the contaminants away from the vicinity of the occupied on-site buildings. The contaminants in Area E ranged from 0.05 to 5.5 m in depth. Area F encompassed the ore storage yard. Contaminants in this area ranged from 0.18 to 1.2 m deep. Washes, however, had contamination exceeding 7.6 m deep.

Jan 1, 1981

By K. Holmberg, D. Herriot

This paper by Mr. McIvor is yet another contribution to the eternal controversy surrounding the benefits, or otherwise, of high circulating loads in closed circuit grinding. Throughout the paper it is difficult to establish whether the author is referring to effects relating to the mill, classifier, or to the overall circuit. Table 1 is put forward as indicating the advantage of operating at high circulating loads. From the two (it would be interesting to see more) product sizing points provided in each case, the conclusions to be drawn are that cases one and two have very similar size analyses. The third case, however, indicates a much flatter curve, that is to say, higher fines production and a very wide spread of size ranges. If the objective of this circuit is to provide a closely sized product with minimum overground slimes to the downstream process, then it would appear to be the less "efficient" by far. No data is given for product pulp densities either. The term "efficiency" should never be used without a careful and clear definition. In this case, "efficiency" is used to express an apparent percentage reduction in operating work index (Bond) from the measured "standard" at 250% circulating load operation. The Bond calculation is itself based upon

Jan 1, 1990

By C. K. Blankenship

The competitive forces now driving the electric utility industry and the constraints of regulation at all levels are changing the way we will all do business now and into the next century. Utilities are using every technological tool at their disposal to find optimum solutions to challenges in every aspect of operations. In fuel planning and procurement, these tools include models that predict which dispatch line-up will comply with environmental regulations at minimum cost. This paper presents how those tools are being used for Duquesne Light Company.

Jan 1, 1995

By J. Groff

The Getchell and Twin Creeks mines are located along a north-northeast trending structural zone in Humboldt county, Nevada approximately 40 miles northeast of the town of Winnemucca. Gold mineralization at the Getchell mine is represented principally by sulfide-rich ores, which contain significant amounts of realgar and\ orpiment, with the gold being recovered through processes which involve pressure oxidation. In contrast, oxide ores are currently being mined and processed at the Twin Creeks mine although large reserves of sulfide ores, some of which contain orpiment-realgar-stibnite, have been defined (Bloomstein et al., 1990). The Getchell and Twin Creeks mines represent major gold orebodies but very little has been published pertaining to mineral paragenesis and the characteristics of ore-forming fluids for these deposits.

Jan 1, 1994

By W. S. Fyfe, R. J. Puddephatt, S. Zhou

Gold is easily mobilized at temperatures within range 600-11OO°C by gases such as Cl2, CO, H2S, in gas mixtures, at low pressures. Such gases are relevant to conditions of granulite facies metaomorphism in environments of magma underplating. These observations suggest an efficient mechanism for moving gold to the upper crust during major thermal events. The efficiency of precipitation of gold at lower temperatures is related to available mineral surfaces and pyrite appears to be an excellent substrate for gold precipitation.

Jan 1, 1989