Search Documents

By Eduardo Poltronieri Trés, Anderson Denadai Thomazini, Rodrigo Boyer Fernandes, Francisco de Assis Dutra Macedo, Gilvandro Bueno, Maycon Athayde, Rossano Augusto Pilon Nunes

The earliest industrial application of high pressure grinding rolls (HPGR) at comminution was in 1984 in the cement industry. Since then, the equipment has been widely applied in mining activities. Despite the rapid spread across the industry, several challenges are still present in the equipment’s application, especially considering the complex ore breakage behaviour reported for this process. The pellet feed’s HPGR comminution was recognized as fundamental to efficiently increase the particle surface area (e.g., blaine specific area, BSA) at a lower energy and water consumption level (Chapman et al. in J Southern Afr Instit Mining Metall 113:407–413, 2013). The present study considers a novel milling process applying only HPGR as a re-regrind stage after concentration. The amount of successive ground product recirculation into the machine to achieve the required particle size for the pelletizing process was investigated. The study compared the ball wet milling process with the innovative processing technology for hematite–goethite ores. Green pellet balling and induration processes were simulated in bench and pilot scale. The milling results showed a considerably steep increase in BSA after each recirculation step into the HPGR, although compared with the ball-milled product the size fraction <45 μm% increased a modest five percentage points after three recirculation cycles, remaining steady until the last recirculation step. As a result, the green pellet generated presented higher concentration of pellets between 10 and 16 mm (%10-16 mm), with a higher drop number than typically observed when produced with ball-milled feedstock. Consequently, on the induration process, a higher pellet deformation was observed during the pot grate loading. Despite that, the fired pellets still presented an outstanding performance in cold crush strength (CSS) considered suitable to an industrial application.

By J. Fox, C. Allen, A. Greth, K. Kocsis

"It is the duty of the mine operator to ensure the mine environment is healthy and safe for the mine workers. For deep and hot underground mines, this requires maintaining adequate working temperatures by means of mitigating the heat load generated by strata, auto-compression, mining equipment, explosives, ground water, and human metabolism. The heat load is best reduced by minimizing the amount of heat transferred to the mine air from these sources and through the use of efficient ventilation with effective cooling systems. The heat emitted by mining equipment and vehicles contribute a significant proportion to the combined heat load of an underground mine. This is especially a problem for diesel equipment due to the fact that besides heat, a large amount of water vapor is produced, which increases the humidity in the production workings. Diesel engines have proven advantageous in recent history due to their high power output and reliability. However, as mines continue to become more mechanized and deeper the climatic problems introduced by elevated heat generation will continue to rise. With that, the issue of heat generated by diesel equipment must be addressed. The economic alternative for diesel engine equipment fleets in underground mines is the electric engine. Technological advances in battery technology, increased mechanical output and improved reliability have made the electric engine significantly more competitive in comparison to diesel engines. Because electric engines do not utilize internal combustion, the heat produced by them is significantly less than of the diesel engines. Battery powered mining equipment likewise eliminate diesel particulate matter (DPM) produced by diesel engines. Utilizing battery electric equipment in underground mines provides many advantages, such as: (a) reduced heat load, (b) healthier and safer environment for the mine workers, and (c) reduced mine operating costs due to lower ventilation requirements. This paper will highlight the health and cost benefits of using battery/electric fleets versus diesel fleets in deep and hot underground mines. The study analyzes simulations produced from thermodynamic ventilation models. Early simulations show significant cost reductions in terms of net present value (NPV) when comparing the air volume requirements for battery/electric equipment versus diesel powered equipment for the same production rate. INTRODUCTION The competitiveness of the world mineral market demands that mine operators continue to increase production and decrease costs as commodity prices fluctuate in often unplanned directions. This has forced underground mines to operate at deeper depths and to become more mechanized to remain competitive. Because of these changes, ventilation challenges have continued to increase as the mines combat an enlarged influx of contaminants such as heat and diesel particulate matter (DPM)."

Jan 1, 2018

By Paul C. Miclea

Hanford Reservation, in the State of Washington, with its deep basalt formations, is one of the three sites recommended by the Department of Energy for detailed investigations in order to select the first nuclear waste repository in the United States. Information obtained from several deep bore-holes drilled at Hanford indicates that the underground facility can be developed in one of the major basalt flows belonging to the Grande Ronde Formation in the Columbia Plateau, at depths greater than 3200 ft. One of the main concerns in the underground repository design is the achievement of acceptable environmental conditions during the development and the operation of the repository. For this, ventilation and air-conditioning are of prime importance and should be fully addressed. Besides the factors that determine the airflow requirements to meet the personnel and equipment operation needs, there are two major concerns that impact on the ventilation system design: the temperature of the in situ virgin basalt rock and the influx of groundwater. These two factors are related by the fact that the groundwater has the same temperature as the rock itself and they both constitute main sources of heat underground. Current information indicates that the temperature of the virgin rock at a depth of around 990 m (3250 ft) is 52°C (12S°F). However, there are some indications that the rock temperature at the selected horizon might be higher. This paper addresses the impact of the virgin rock temperature on the ventilation system and air-cooling requirements. Graphs with heat loads and cooling required for different rock temperatures have been prepared for a given model and network, using computer techniques for simulating the climatic parameters.

Jan 1, 1987

By Nasib Al Habib, Hooman Askari-Nasab, EUGENE BEN-AWUAH

In-pit crushing and conveying (IPCC) is getting popular in deeper open pit mines as a suitable alternative to truck haulage because it offers a lower operating cost due to shorter haulage distance and less truck requirement. Semi-mobile in-pit crusher, currently the most popular IPCC system, is relocated every two to five years, and the short-term plan needs to be updated accordingly. To the best of our knowledge, short-term planning with IPCC is an area of research that has yet to be explored extensively, and hardly any model can generate a shortterm extraction sequence considering an IPCC. This research work proposes a mixed integer programming model to develop a short-term production plan within a time horizon of 12 months. The model's objective is to optimally allocate shovels to minimize the cost of material handling and maximize revenue subject to meeting plant requirements, maximum allowable tonnage variation and IPCC location constraints to achieve production and NPV targets set by the strategic plan. The proposed model will be implemented in an iron ore mine case study for verification. The model is developed and solved using MATLAB. The comparison of results between scenarios with and without IPCC justifies the use of IPCC in large open pit mines from a short-term perspective.

Jun 25, 2023

By K. Luxbacher, D. T. Hristopulos, S. Schafrik, J. Diaz, Z. Agioutantis

Big data is generated from both surface and underground mining operations. Such data contain a wealth of information concerning safety and health in the workplace and production parameters. This paper will discuss the progress towards developing an accurate forecasting model for methane gas concentration based on the analysis of data collected from Atmospheric Monitoring Systems in underground coal mines employing time series models. Several procedures need to be applied to raw data, such as data cleaning and filtering for outlier removal, data homogenization and segmentation, and exploratory statistical analysis. The data analyzed were retrieved from two coal operations in the Eastern US. A negative correlation between barometric pressure and methane gas concentration was established, at least for certain data segments. Such correlations raise the possibility that barometric pressure data can predict variations of gas concentration in the mine. The datasets will be further investigated to establish the robustness of barometric pressure and gas concentration correlation and explore the dependence of gas concentration on other factors related to mine design and operations

Mar 2, 2022

By Mahmud Esad Uluer, Aaron Noble

Respirable coal mine dust (RCMD) is one of the biggest occupational health hazards for underground coal miners. Coal extraction is a main source of RCMD. To prevent challenges related to RCMD from developing, it is vitally important to limit airborne RCMD and stay within the regulatory limitations for mine operators. The flooded-bed dust scrubber (FBS), mounted on a continuous miner, is one of the most widely used dust mitigation technologies in room-and-pillar mining, but it is limited by technical challenges, the most notably being the potential to clog. In this study, the impact of mesh design and surface modification on system efficiency is examined using different vibrating, liquid-coated, stainlesssteel mesh panels in a laboratory-scale FBS.

Sep 1, 2024

By Charles T. Staniek

Following a dragline relocation at Agrico&apos;s Fort Green phosphate mine in 1986, the recovery plant experienced a significant decrease in flotation performance. Through weeks of trial and error testing, we discovered we could restore recoveries by conditioning feed at pH&apos;s higher than we had used historically. The higher pH&apos;s essentially increased flotation cell kinetics, although we still do not understand the exact mechanism at work. Armed with new-found appreciation of pH modification, we initiated a program to determine the optimum modifier for us, from both a performance and environmental perspective. Environmental considerations were important because ammonia, the standard industry modifier, is a plant nutrient and higher usage rates could affect the quality, of our recycle process water. This paper describes the research and development work spanning a 3 year period that culminated in making a major change in our reagent suite when we replaced ammonia with soda ash on a permanent full-time basis.

Jan 1, 1993

By M. Hancer

The sign of the surface charge of selected potassium soluble salt minerals namely KClO4 , K2SO4 , KNO3, and KCl was determined from nonequilibrium electrophoresis measurements and found to be negative for each of the salt. Dodecylamine flotation of these salts revealed that the concentration of amine required for flotation increases in the order KClO4< K2SO4< KNO3<KCI. Precipitation of the amine collector colloid was not required for flotation of the oxyanion salts and in this case it appears that adsorption of the dodecylamine cation is sufficient to create the hydrophobic surface state. The order for flotation is explained in terms of surface hydration of these respective potassium salts based on contact angle measurements and FT Raman spectroscopic characterization of water structure.

Jan 1, 1999

By M. A. Schimmelpfennig, A. D. S. Gillies

M.J. McPherson Having worked on the thermodynamics of air/liquid-water mixtures passing through the surface fans of deep mines, I find this paper of great interest and congratulate the authors on producing it. There are two matters, however, deserving discussion. First, the authors have described the classical theory of fog formation with fogging occurring at "supersaturation." In fact, the process of fog formation begins well below 100% humidity. The more strongly hygroscopic nuclei in the atmosphere will attract water molecules and begin to grow at a relative humidity perhaps as low as 70%. The process is a dynamic one with both condensation and evaporation taking place throughout the mixture on microscopic liquid surfaces. As saturation is approached, the rate of condensation accelerates rapidly producing the familiar reduction in visibility. Hygroscopic nuclei are present in all natural atmospheres and under the appropriate conditions of pressure and temperature, will produce clean fogs. However, if the air is polluted by particulates from combustion or other processes then the resultant coagulation with growing liquid particles may produce dense (and sometimes photochemical) smogs. It is this process that is likely to occur in underground mines when moist air is cooled below dew point. Second, the authors have summarized very well the individual measures that might alleviate the problem. In particular, I agree that neither heating nor refrigerating the air, by themselves, provides a satisfactory solution. However, there is a combination of these that provides a neat and effective control of fog formation. This involves a small, self-contained refrigeration unit within a duct but without the usual external heat rejection facility. The air is cooled below dew point and, hence, dehumidified on passing over the cold evaporator coils. The heat from the condenser is rejected back into the air downstream from the water eliminator, as shown in Fig. 1. The duct configuration can be designed to create good mixing at the outlet. I have used a climatic simulation program to illustrate the effect, assuming a 500-m (1,640 ft) long airway of cross section 60 m2 (645 sq ft), an airflow of 9 m3/s (318 cu ft per sec), inlet conditions of 19/19.25°C (66/67°F) wet bulb/dry bulb temperatures, a virgin rock temperature of 17°C (63°F) and typical rock thermal properties for a hard-rock mine. I have also assumed that 10% of the rock surface is wet. Figure 2 shows the variation in temperatures along the airway if no measures are taken. The relative humidity remains close to 100% and condensation will occur throughout the length of the airway. Before any such installation is designed, the exercise must, of course, be repeated for each location with accurate data. However, this example demonstrates the potential of the system. The idea is not new - the principle is sometimes used in air-conditioning plants for buildings. Figure 3 shows the effect of removing 30 kw of heat by evaporator coils sited 40 m (131 ft) along the airway and rejecting that heat (plus another 10 kw of compressor and fan power) into the air at 60 m (197 ft). Condensate water is produced, at a rate of 0.45 L/min (0.12 gpm). The result of this sequential cooling/dehumidification/heating process is to separate the wet and dry bulb temperatures along the length of the airway. The relative humidity increases from 80% at the duct outlet to 92% at 500 m (1,640 ft). The airway is maintained free from fog.

Jan 11, 1983

By J. Twining, V. Nguyen, J. Perera

A computer code for ecological risk assessment (ERA), AQUARISK, has been developed and applied to evaluate the likelihood of biotic detriment due to exposure to acid rock drainage (ARD) from the Burkunga mine site in Australia Stream water quality monitoring data were used for the assessment and were compared with a) national water quality guidelines, b) literature derived ecotoxicology data and c) biological monitoring data. With bioavailability calculations, the code predicted that, for metals exceeding the guidelines, 44% of macroinvertebrate species above the mine and 100% below the mine would be adversely affected by the metals in the stream. This compares reasonably and conservatively with biological monitoring that showed observed reductions of 41% and 85% of species respectively at each site. Using literature data for macroinvertebrates to predict impact produced similar estimates to using data for all taxa. Use of speciation modeling also lessened the degree of reduction in the median water metal concentrations required to achieve acceptable impact (measured either by exceedence of criteria or by species likely to be affected) by a factor of 75%. This result implies significant economic and management benefits in relation to remedial engineering or water treatment options for sites.

Jan 1, 2000

By E. M. Cukrowska

The evaporative pan complex consists of two adjacent seasonal pans. These pans carry an exceptionally high salt (TDS) load due to over 50 years of effluent discharge via the pipeline from mines. The nutrient, heavy metal, radionuclide load in the water and sediments of the pans are very high affecting groundwater around the pans. The groundwater in the region contains TDS > 40 000 mgl-1 and sulphates > 7000 mgl-1, whereas groundwater in areas assumed to be unpolluted by mining activities have TDS < 500 mgl-1 and sulphates < 200 mgl-1. The extent of continuity between the pans and the groundwater is unknown, although there appears to be seepage of contaminated groundwater into the river system.

Jan 1, 2006

By H. P. van Ormer

The objective of this paper and the developed personal computer program is not to identify or try to identify the actual total drilling cost in any Rotary Drilled Blast Bole Program. The ideas put forth here and in the computer program developed are a very accurate way to measure what is often very hard to identify and interpret -The actual direct operating cost of various drilling package combinations including comparing with available blast hole sizes and patterns

Jan 1, 1988

By P. K. Gbor

Over 2 million tonnes of smelter slags containing Co, Ni and Cu are produced and stockpiled in Canada each year. Smelters also produce SO2 an air pollutant. Recycling these materials will maximize the value of natural resources and minimize possible environmental impacts of industrial operations. The objectives of this research were to understand the characteristics of slag, the reaction of slag with SO2(aq) and to develop a novel method for extracting Co, Ni and Cu from slag using SO2. The properties of slags from different smelters were studied, with emphases on the form of Co, Ni, Cu and Fe. Leaching experiments were carried out in a batch reactor. The parameters investigated included concentration of SO2(aq), stirring speed, particle size, temperature and pH. O2 was introduced into the reactor to study its effect on the system. The amount of each of Co, Ni and Cu in all the slags was less than 1%, while Fe was between 30% and 45%. The form of Co and Fe was primarily oxide, however, significant portions of Ni and Cu were present as sulphides. SO2(aq) alone, was effective in leaching Co and Fe. Cu dissolution was negligible due to precipitation. The presence of O2 improved Cu and Ni extraction. SO2(aq) was found to be more effective in leaching slag than H2SO4 at the same pH. The leaching process was modelled using the shrinking core model. A scheme was proposed for the extraction of Co, Ni and Cu from slag using SO2(aq). The process makes efficient use of SO2, separates Co and Cu at an early stage, and minimizes the consumption of base during Fe separation.

Jan 1, 2003

By Hazal Melis Aytac, Lana Alagha, Fardis Nakhaei

Gallium (Ga) and Germanium (Ge) are essential strategic elements that are extensively used as semiconductors in many technological fields. Owing to their essential uses and supply disruption, Ga and Ge are deemed critical by the U.S. They are typically found as substitutions or inclusions in zinc minerals. However, their distributions within zinc minerals are not well understood. To address this, trace element and mineralogy analyses of representative samples obtained from an old high-zinc-grade tailing were performed using various qualitative and quantitative techniques. These techniques included Inductively Coupled Plasma Mass Spectrometry (ICP-MS), Tescan Integrated Mineralogical Analysis (TIMA) with Scanning Electron Microscopy (SEM) and X-ray Diffraction (XRD). Moreover, bench-scale froth flotation tests were conducted to enrich zinc minerals, the major hosts of Ga and Ge, using PAX as a collector, Na2S as a sulfidizer, Pb(NO3)2 as an activator, and MIBC as a frother. Comprehensive characterization analyses of the flotation products showed significant enrichment of Zn, Ga and Ge in the flotation concentrates.

Feb 1, 2025

By B. Suresh, Kalyan K. Das, Pradip

A series of salicylaldoxime derivatives with alkyl group substitution in the main chain and the side chain were synthesized and evaluated for the flotation of malachite, cerussite and smithsonite. The effect of chain length and the position of the substituent group on the selectivity of separation amongst oxidized copper, lead and zinc minerals are discussed in this paper.

Jan 1, 1995

By Hayati Karaman, Tevfik Güyagüler

In this paper fires due to spontaneous combustion in Middle Anatolian Lignite mine (OAL) which is the first fully mechanized underground lignite mine in Turkey, are studied. Since the installation of mechanization (1986), due to spontaneous heating, four panel fires namely, A01, A02, A03 and A04 have broken out. During these fires, the concentrations of carbon monoxide, methane and the velocity of air are measured continuously by the Micro Minos Environmental monitoring system. For each fire, the environment where fire has started is examined and the possible causes of the fire are investigated. Also the precautions taken to extinguish the fire at different stages are described and the importance of the early detection of mine fire are discussed together with the limitations of the monitoring system and the practical difficulties observed during the fire.

Jan 1, 1995

By D. Kidd, T. Tucker, L. M. Indergard, S. Davis

"INTRODUCTION The Lisbon Valley Mining Co LLC (LVMC) operates the Lisbon Valley Mine located in SE Utah. The mine includes 3 open pits, 150-acre heap leach pad, and solvent extraction electro winning plant (SX/EW). Approximately 25MM tons of ore has been mined since 2005. The ore is stacked on the leach pad to an average height of 55 feet and occurs as a blend of crushed material (minus 2”) and run-of-mine (minus 24”). The host rocks include Dakota and Burro Canyon Sandstones. Copper occurs finely disseminated in this material at an average grade of 0.46%. Minerology is 63% sulfide, 27% oxide, and 10% insoluble. Total inventory mined through 2016 is approximately 230 MM lbs. METALLURGICAL CONSTRAINTS Copper production is constrained by areas of low permeability ore and geochemical issues, including acid consumption. The intrinsic permeability the ore ranges from 10-2 to 1 Darcy. This permeability does not permit sufficient aeration by natural convection, therefore oxygen transport is largely limited to the mass of oxygen that can remain dissolved in leachates. As a result, greater than 50MM lbs of copper remains in inventory and occurs secondary sulfides, including chalcocite, covellite, and bornite. BIOLEACHING FUNDAMENTALS Due to the higher activation energies of secondary sulfides, notably covellite and bornite, a strong oxidant is needed to remove an electron from the metal-sulfide lattice and release the copper cation into the sulfate solution. This process occurs most efficiently using the strong oxidant ferric iron (Fe3+). Ferrous iron can be oxidized to ferric iron by oxygen via chemical oxidation or biologically; which was measured to occur 500,000 times faster when using microbes versus oxygen.1 The microbes that oxidize ferrous iron (Fe2+) to ferric iron are naturally abundant and will develop biomass when appropriate conditions and nutrients present themselves. Most nutrients are provided by the ore/irrigation (P,N,Mg, Ca & Fe2+) while the others (O2 and CO2) are provided by air. In most cases, oxygen transfer is the rate limiting step during copper sulfide leaching. 1 Lacey & Lawson 1970 FORCED AERATION SYSTEM DESIGN This paper describes LVMC’s efforts to bioleach the remaining inventory by forced aeration. Two basic aeration systems were installed and tested including vertical wells and horizontal piping. Vertical System The vertical system was installed using the mine’s blast hole drilling rig. Wells were constructed using 4” high-density polyethylene (HDPE) connected to 4” polyvinyl chloride (PVC) screens similar to conventional bioventing wells. Ore samples were collected at each well location to characterize the spatial distribution of the remaining inventory along with fines (minus 200 sieve), pH (acid consumption), and iron. A block model of each analyte was developed and mapped in 3D."

Jan 1, 2017

By L. R. Shotwell, C. F. Voss, R. J. Bastian

Pacific Northwest Laboratory (PNL) currently supports the U.S. Department of Energy&apos;s Office of Civilian Radioactive Waste Management in developing and evaluating analytical methods for assessing the suitability of sites for geologic disposal of high-level radioactive waste. The research includes consideration of hydrological, geomechanical , geochemical , and waste package components and the evaluation of the degree of coupling that can occur between two or more of these components. The PNL effort and those of other research groups investing potential waste sites in the U.S. and abroad are producing a suite of computer codes to analyze the long-term performace of the proposed repository sites. This paper summarizes the ongoing research in rock mechanics at PNL involving flow through jointed rock. The objective of this research is to develop a methodology for modeling the coupled mechanical-hydrological process of flow through joints and then attempt to validate a "simple" model using small -scale laboratory test data as a basis for judging whether the approach has merit. This paper discusses the laboratory tests being conducted to develop s joint behavioral constitutive model for the numerical method under development and the modeling approach being considered.

Jan 1, 1986

By Faruk Oksuz, Clay Haynes, David Egger

The United States Army Corps of Engineers (USACE) has committed to solve a major drainage problem in the suburban Chicago community of Griffith, Indiana. The Cady Marsh Ditch is currently undersized and on occasion spills its banks causing flooding and economic setbacks to the community. Preliminary studies have identified both tunnel and surface solutions as being attractive and viable. The USACE has decided that this project is an opportunity to use the design-build contracting approach to maximize ingenuity in project approach and to allow the market to dictate whether a surface or subsurface solution is most attractive. The tunnel would be over one-mile in length through sands, gravels and clay. Water control will be an issue during tunneling. The paper will explore the contracting approach to the project and the adaptation of Underground Technology Research Council (UTRC) guidelines for underground contracting to a design build project. The roles of Owner, Owner’s consultant, and design-build contractor will be defined as interpreted by the USACE and key contract provisions will be described and contrasted with a traditional design-bid-build approach to tunnel construction.

Jan 1, 2003

By Jurgens PE Hamman, Faisal Putra, Hadnaltias Alpeki, Willem de Beer

The Deep Ore Zone mine is the third lift of caving at PT Freeport Indonesia’s East Ertsberg Skarn System. An increasing trend in seismicity along the northern boundary of the DOZ cave, as well as the northern fringes of the DOZ production and infrastructure levels, was taken as indicative of an interaction between the approaching DMLZ cave and the DOZ subsidence zone. Seismicity trends and locations indicated a reducing crown pillar and an associated stress increase along these DOZ excavations, as well as the regional area along the DOZ cave boundaries. Although rockbursts were not identified as an immediate hazard, seismic shakedown was a highly probable hazard in the case of remote large (≥3.0) seismic events. An evaluation process, as described in the Canadian Rockburst Support Handbook (1996), was followed to identify and quantify the various parameters that could contribute to a shakedown evaluation. A shakedown assessment, based on the Peak Particle Velocities scaling relation, was conducted to assess the current installed ground support systems along the northern fringes and the fixed facilities of the DOZ mine. The range in ground support systems were mostly due to different geotechnical environments. The load–deformation characteristics of these support systems were evaluated to determine the support capacity and compared to the potential support demand under varying shakedown conditions. Shakedown hazard maps were compiled to indicate the installed ground support system’s vulnerability to seismic shaking. Based on this information, areas were divided into zones indicating whether they were sufficiently supported, additional support was required, access was to be restricted, and / or they were to be abandoned. Mine management utilised these hazard maps to strategize actions for the various operational zones within the DOZ, including the fixed facilities. This paper briefly describes the derivation of the PPV scaling relationship. Seismic and geological data for the DMLZ – DOZ interaction areas were evaluated to determine the likely source of large events. Subsequent larger events and their effects are shown to assess the veracity of the magnitude and PPV estimates, as well as the effectiveness and appropriateness of the ground support systems.

Apr 26, 2022