Search Documents

By C. Roldan, C. Garcia, J. D. Miller, C. L. Lin

The ultimate recovery in a heap leaching operation is related to the degree of exposure of the valuable minerals in comminuted particles. Recently, high-resolution cone beam x-ray microtomography (XMT) has been used to determine this parameter. XMT technology consists of examining the extent of mineral exposure for each size fraction of ore in 3D, then, by algebraic calculations, the ultimate recovery can be estimated for different particle size distributions (PSD). To confirm the usefulness of the XMT technology for mineral exposure analysis, column tests were performed to determine ultimate recovery using three PSDs for two composites obtained from the copper heap leaching operation at Zaldivar-Chile.

Jan 1, 2003

By S. Helgen, C. Byrns, A. Davis

The 4000 acre historic Robinson Mining District outside Ely, Nevada hosts a continuum of oxidelsulfide waste rock dumps of different ages. In an effort to develop a paradigm to explain past, existing, and future conditions at the site profiles of oxygen, pH, temperature, and specific conductivity were collected from various waste rock dumps using a hand-driven soil gas probe and a down-hole sampling device. The resulting data are useful in interpreting the fate and manner of pyrite oxidation within the dumps and in identifying waste rock dumps that may require remedial measures compared to those that require only minimal action prior to closure.

Jan 1, 2000

By Yoginder P. Chugh, K. V. K. Prasad, R. Missavage

This paper presents results of field monitoring and finite element studies to analyze and improve a room-and-pillar retreat mining system. Fie1 d instrumentation was utilized to monitor pi11ar load changes, roof to floor convergence and differential roof strata movement as retreat mining progressed and to determine in-situ horizontal stresses. A two-dimensional finite element model depicting strata behavior at this mine was developed and used to analyze existing and alternate improved mining geometries. The results showed excellent correlation between fie1 d observed and model predicted behavior. Some of the recommended changes in mining geometry based on the study were incorporated in the mining system.

Jan 1, 1986

By Ehsan Moosavi, Kamyar Tolouei

In open-pit mines, the long-term production scheduling optimization problem (LTPSOP) is a complicated problem that contains constraints, large datasets and uncertainties. Due to its dimensions and NP-hard nature, it is usually difficult to find an ideal solution to the LTPSOP. The optimal schedule generally restricts the ore, metal and waste tonnages, average grades, and cash flows of each period. In this paper, to synthesize grade uncertainty into the strategic schedule, a stochastic integer programming (SIP) framework is presented to LTPSOP. The objective function of the SIP model is to maximize the net present value and minimize the risk of deviation from the production targets considering grade uncertainty simultaneously while satisfying all technical constraints and operational requirements. Instead of applying one estimated orebody model as input to optimize the production schedule, a set of equally probable orebody realizations is applied to synthesize grade uncertainty in the strategic schedule and produce a more profitable and riskbased production schedule. To solve the LTPSOP, the hybrid approach with the augmented Lagrangian relaxation method, the Harris Hawks optimization, the Random Forest method and Monte Carlo method was proposed. To indicate the applicability of the model, a case study on a gold mine was implemented. The framework displays the capability to minimize risk and improvement in the expected net present value and financial profitability .

Jun 25, 2023

By D. T. Kirkwood

The practice of impounding mine water and liquid fine waste in underground mines is increasing. Often these underground impoundments are created by constructing seals or bulkheads designed to withstand the expected hydraulic pressures. Occasionally seals are built for another purpose, usually to act as explosion-resistant ventilation barriers. Due to factors such as clogged drain pipes or unexpectedly high inflow rates, these explosion-resistant seals sometimes become subjected to hydraulic pressures. The incidence of seal failures due to inadequate design and/or construction is also on the increase. Fortunately, to date, no lives have been lost by water seal failures, but a clearer understanding of the design and construction considerations specific to water seals is vital to keep this from occurring in the future. This paper presents technical considerations for the design and construction of seals which will specifically be required to withstand hydraulic pressures in underground mines.

Jan 1, 1995

By Siegfried Zell

Preface Pipe heading is a customary and proven technology for the underground installation of all types of piping. In over 90 % of all cases, straight pipe sections are used between shaft constructions since, e.g. this follows roadways or it is necessary from the operational aspect due to pipe control methods, e.g. to use a remote control pipe sensor or comparable control devices within sight from shaft to shaft. Frequently, a straight pipeline is impossible, and is replaced by a more or less spatial alignment due to surface conditions, structures in the ground or foundations. This situation applied for the construction of the Nebensammler Neuland (intercepting sewer) in Hamburg-Neuland for sections IV and V. The following paper is not intended as a description of the complete project. It deals mainly with the special features of this pipe heading, with what I believe to be its somewhat unusual route. The task The building authority design issued by the Main Department for Urban Sewerage of the Free and Hanseatic City of Hamburg consisted of the construction of the collector by a pipe heading using NW 1300 pipes in 2 heading sections. One short straight and one long

Jan 1, 1989

By I. Iwasaki

The presence of calcium ion in iron ore pulps causes heterocoagulation of montmrillonite on hematite leading to indiscriminate dispersion. Two methods were investigated to control the adverse effect of montmorillonite: chemical method using such complexing agents as EDTA and sodium tripolyphosphate, and mechanical method involving ultrasonic treatment. Their roles in controlling the adverse effect were investigated by zeta potential measurements, starch adsorption tests, and flocculation and selective flocculation tests.

Jan 1, 1986

By Felicia F. Peng, Victor Z. Sun, Syd S. Peng

A probability-based analysis method in conjunction with the finite element structure modeling technique to evaluate an entry system stability is developed. Variability of the rock properties and loading surrounding the entry system is taken into consideration to predict a roof stability by using the probability of failure instead of the common safety factor concept. A dynamic programming is applied to establish a recurrence relationship between the degree of potential roof fall and accumulated roof fall index in an area of interested. A probable distribution of roof fall is assessed by using a developed computer program, RFSTAB. The assessment of the roof falling boundary in the longwall entry system is used as the example to illustrate the procedure and effectiveness of this analysis method

Jan 1, 1996

By Ian S. Lowndes, Adrian T. J. Moll

With the current trends towards the concentration of extraction to fewer but higher production units in deeper seams, often of higher coal rank, the role of methane drainage ranges has become critical. As mines exploit seams at greater depth and more remote locations there has been a need to extend the lengths of methane drainage ranges and to increase the capacity of the surface pumps. This trend has highlighted the need to effectively simulate the operation of a methane drainage range in order to produce the optimum design and operation of a safe and economic system. This paper describes the development of such an analytical tool. The application of this computer model is illustrated by the analysis of the operation of the drainage system of an extensive mine. The paper concludes by considering the development of a [Knowlege Based or Decision Support System] which will assist the ventilation engineer in assessing the current performance of an existing drainage range and will suggest possible remedial modifications or design strategies which may improve the system performance. INTRODUCTION In order to maintain the general body methane levels to below predetermined statutory threshold limit values (TLV's) on major longwall production units there are, for a given production rate, two major complementary control devices which may be employed by the ventilation engineer. These are the combined design and application of a competent mine ventilation and methane drainage system. The methane drainage system should be designed so as to maximise the capture of the methane (firedamp) from the seam being mined and the strata gas liberated in the vicinity of the extraction zone from gas bearing seams or other reservoirs of gas situated at above or below the mining horizon. The design fresh air quantity entering the face should ensure that under normal operating conditions the methane entering in the vicinity of the face is rapidly dispersed and dilute to well below statutory TLV's. The drainage system must therefore be designed to maximise the capture of the methane gas liberated to minimise the amount of gas which enters the ventilation airstream. GAS DRAINAGE The inherent dangers of methane emissions in mine workings have been a problem of concern to mining engineers for many years. To alleviate the risk, methane drainage has been employed for some years to capture the gas before it becomes a hazard to the operation of the mine. The method of drainage employed will be dependent on a number of factors which include the longwall mining method and production cycle employed, the characteristics of the coal seam being extracted and those of the adjacent gas bearing strata. The location of the gas bearing potential of the over and underlying coal measures must be determined. The gas bearing

Jan 1, 1993

By R. Kealey, D. Huo, Q. Zhang, Y. A. Sari

Greenhouse gas (GHG) emissions from primary mineral and metal production account for ~10% of global GHG emissions. One of the main sources of GHG emissions in mining operations is fuel consumption by haul trucks. Given their size and carrying capacity, the fuel consumption of haul trucks can approach 250 liters per hour. An average of 30% of the idle time of the trucks is spent while waiting in the queue. Inefficient truck dispatch planning can waste resources, cause dilution and elevate GHG emissions. In this research, a machine learning based truck dispatch approach was developed to dynamically route the haul trucks based on the loaded material, the road traffic, the estimated wait time, and the maintenance needs of the trucks. The GHG reduction potential of this smart fleet management approach was estimated by calculating and comparing the related carbon emissions versus scenarios using traditional fleet allocation approaches. Results suggest that this dynamic fleet allocation approach can significantly reduce GHG emissions at mineral production sites by optimizing waiting times and the overall distance travelled while achieving the same production levels.

Mar 2, 2022

By Babu R. Yama

Artificial Intelligence research has produced several tools for commercial application. Neural Networks, Fuzzy Logic and Expert Systems are some of the techniques that are widely used today. Artificial Neural Networks (ANNs) are excellent predictive, pattern recognition, and data analysis tools. In the mining industry, ANN techniques are being used commercially for real-time process control applications. Modeling of spatial data, ore reserve estimation, tunnel design, longwall stability prediction, and geologic roof classification are additional application areas in which neural networks have been applied successfully. A standard back-propagation algorithm was used to train a series of neural networks for a real-world predictive task. After training and optimizing the neural network architecture, performance of the network is measured on an independent validation set. Results indicate a correlation coefficient of up to 84 % between the actual and predicted values. A neural network model is developed for learning the spatial continuity of a mineral field and, consequently, for predicting sulfur values given coordinate values. The neural network performed not only satisfactorily, but in some cases performed better than the kriging model.

Jan 1, 1997

By Liam Findlay

Optimizing a production schedule with semi-mobile in-pit crushing & conveyance (IPCC) requires integrating extraction sequence, destination policy, crusher relocation, conveyor layout, and truck fleet investment decisions. An integrated stochastic optimization framework is proposed to produce long-term schedules for mining complexes using multiple semi-mobile IPCC systems. The optimizer selects the crusher locations and designs the conveyor routes from anywhere in the mines. The stochastic framework considers simulated multi-element orebody realizations and manages associated risk. A hybrid metaheuristic based on simulated annealing and evolutionary algorithm is implemented for the optimization. The method is demonstrated using an iron ore mining complex.

Jun 25, 2023

To simplify programming, image analyzers commonly measure either linear intercepts or the areas of particles and grains to determine liberation based on polished section mounts. However, the concentration of minerals by flotation is based on reagents that interact with the exposed surfaces of the minerals. Thus, it is often perceived that image analyzers should measure the perimeter of the mineral of interest in the ore particles. A comparative liberation study of thirteen samples collected from a flotation plant processing a complex base metal sulfide ore showed that the liberation of the ore minerals determined by area measurements is very similar to the liberation determined by the exposed perimeters. The liberation determined by exposed perimeters is more appropriate only for those cases where the mineral texture is so complex that it is retained in the small particles generated in conventional grinding operations. Key words: Mineral liberation, Flotation, Image analyzers

Jan 1, 2003

By J. Le Gac, P. Zettwoog, J. Brenot, J. W. Piechowski, J. C. Nenot

INTRODUCTION The components of the radiological hazard in uranium mines are: 1. exposure to radon and its short-lived daughters 2. exposure to long-lived ore dust 3. external irradiation With usual ventilation rates, the dosimetry relative to the first component only requires to know each miner&apos;s exposure to a potential energy of short-lived radon daughters, (EXP[a]). Presently in France, (EXP [a]) is determined monthly from radon concentration measurements. This is an indirect method based on ambient monitoring. After technical improvements achieved during the last years it is now possible to measure (EXP [a] directly with an individual portable monitor developed by the CEA. The purpose of this study is to analyze and compare monitoring results obtained by these methods. DETERMINATION OF INDIVIDUAL MONTHLY EXPOSURES TO[ a] POTENTIAL ENERGY OF SHORT-LIVED RADON DAUGHTERS [(EXP a) amb, by ambient monitoring] In this case, it is necessary to know individual monthly exposures to radon, (EXP Rn). As mentioned by Pradel, J.,et al., 1976, (EXP Rn) is estimated for each worker from informations both on radon concentrations (CRn) measured as described by Pradel, J., 1962 and times (t) elapsed in the various workplaces. (EXP Rn) is obtained by summing up the elementary radon exposures CRn x t relative to all the workplaces where the miner was successively engaged during the month. (EXP Rn) values are then corrected by an average equilibrium factor of 0.17 deduced from many measurements and taken as representative for all the French mines. Finally: [ ] (EXP [a])ind are obtained directly with an individual portable instrument described by Chapuis, A.M., et al., 1972. Samples of the air breathed by the miners are pumped continuously and radioactive aerosols containing the short-lived radon daughters are trapped on a filter. The principle of the measurement lies on track-etch detection of the a particles emitted by the deposited material. The technical aspects have been described by Duport, P., et al., 1980a, Mouden, A., et al., 1980 and Chapuis, A.M., 1980. As mentioned by Duport, P., et al., 1980, fiability is good. Indications on measurement reproducibility are given by Pradel, J., et al., 1977. PRESENTATION OF THE STUDY The underground miner population of a French mine was followed during a period of 8 months (October 1978 - May 1979). Monthly exposure values for each miner determined either by ambient or individual monitoring, (EXP [a])amb or (EXP[ a])ind, had been previously collected by Le Gac, J., 1980, who had also defined miner categories according to the characteristics of the work performed. Four groups are considered here, the "whole mine" and three categories as described in table 1. Data on the individual monthly exposures,(EXP [a])ind and (EXP [a])amb, were taken again to analyze the individual cumulative exposures instead of the "month by month" values. The influence of the mean habits of each individual on its surveillance results is thus taken into account. Each miner has a cumulative exposure as an individual of the "whole mine" and as an individual of each category in which he has worked. The results obtained by ambient or individual monitoring were analyzed (characteristics and adjustements of the distributions) and then compared (description of the discrepancies observed). Obviously, such a study is possible only if all the exposures are cumulated on a same duration. As miners have not worked during the same number of months in the course of the data collecting period, one must considerer the individual average monthly exposures, [(EXP a)]amb and[ (EXP a)]ind, instead of the individual cumulative exposures, which is typically the same thing. To be sure that the exposure values of a given group (A, B, C or D) are representative, only those miners really present for at least 3 months in this group were taken into account. Finally, each individual of the "whole mine" and of the various work categories has a pair of average monthly exposure values : [(EXP a)amb] determined by ambient monitoring and[ (EXP a)ind] deduced from the track-etch recording of the individual portable monitor. Let a miner be engaged during n months[ (3 < n < 8)] in a group, the following relations then apply : [ ]

Jan 1, 1981

By A. A. Terchick

In 1970 U. S. Steel acquired the physical assets of mine, mine property, and preparation plant of the Crystal Block Coal Company near Thacker, Mingo County, West Virginia. The facility, identified as U. S. Steel Mine No. 20, is administered and operated as a production unit of U. S. Steel Gary District, Gary, West Virginia. Mining operations of the No. 20 mine are conducted in the high-volatile Alma seam. The preparation plant, which originally had a capacity of about 150 tons per hour (tph) of raw-coal feed, had process circuitry consisting of a Daniels heavy-media vessel for cleaning the plus-1/4-inch raw coal, a McNally-Pittsburg feldspar jig for cleaning the 1/4 inch by 28 mesh, and Daniels flotation cells for treating the 28 mesh by 0. No water-classification system existed. Refuse tailings from the plant were pumped to several surface lagoons which were decanted to the stream. The settled solids were removed and trucked to the coarse-refuse disposal area. Water make-up requirements were supplied by a small mine-water surface reservoir and augmented with stream water. Expansion of production from the property required an increase in preparation-plant raw-coal-feed rate capacity from

Jan 1, 1974

By Fernando H. Muge

The first application of dynamic pro¬gramming to the problem of grade control and scheduling was by Muge et al (1979) and Ribeiro (1982) who applied it to the simple, two-dimensional case of longitudinal open stoping using two sublevels. In this paper the formulation of the problem is extended to cover the general case applied to a cut-and-fill mining method. The criterion for optimization is the total deviation of the average, grades of mining blocks from the overall average panel grade (or the average grade of a set of mining panels or the mine processing working point). This means to schedule the operation by removing a certain number of mining blocks at a time, subject to the geometric (mining) constraints, and such that the total deviation of average block grades from overall average grade is minimum. The method can be applied to complex orebodies with several ore characteristics and the deviation of each one of these characteristics can be further constrained by specifying maximum values. The method can also be generalised in order to take into account any necessary geometric constraints used to define the mining method. In this paper a case study is presented concerning the mine planning of a complex sulphide orebody located in the South of Portugal. As input for the definition of the mining sequence, a geostatistical numerical model of the orebody was built based on a previous ore typology. The short term planning is used to assess specific mining sequences and the production scheduling is performed on the basis of an objective function (e.g. minimization of grade fluctuation).

Jan 1, 1989

A thermomechanistic model was developed for the thermal decomposition of the enargite contained in a copper concentrate at 650° to 750°C in a fluidized bed with an inert atmosphere. At the particle level, the model permits one to predict the thermal profile inside the reacting enargite particles, as well as their thermal cycle. At the macroscopic level, a population-based model coupled to the bubbling-bed fluidized bed model allows one to predict the fractional conversion (dearsenification) of an enargite-bearing copper concentrate.

Jan 1, 2002

By R. Gong, R. Bhaskar

[Full-scale laboratory experiments were performed to evaluate the effect of ventilation and water spray pressure on the potential dust capture efficiency of a ventilation system comprised of blowing ventilation and an underboon scrubber. The tests were performed for a 1.52-m (5-ft) roof height and 2.36 m-3/s (5000 cfm) blowing ventilation volume, and a 2.44-m (8-ft) roof height and 4.72 m3/s (10.000 cfm) blowing ventilation volume at three face positions of the miner. The scrubber suction rate was varied for the tests to study the effect of scrubber flow rate on capture efficiency. The airflow patterns and scrubber efficiency were determined by performing tracer gas tests. Tracer gas was released through a manifold placed in front of the rotating miner drum. The gas was sampled in a grid fashion using a real-time multi-point gas sampling system. The capture efficiency of the scrubber was evaluated based an the peak gas concentration of the gas laden air drawn through the scrubber and the amount of gas passing, through the scrubber as a fraction of the gas released at the face. The data were analyzed to yield scrubber peak concentrations, potential exposures at various operator locations and the gas removal percentage (GRP). The underboom scrubber appears to work best in the end sump position, relative to the start sump and start slab positions. The capture efficiency scrubber was higher for 2.44-m (8-ft) roof heights compared to 1.52-m (5-ft) roof heights. The data also showed that the scrubber air discharged behind the mining machine may be drawn into the face area by the action of the blowing ventilation system, resulting in recirculation.]

Jan 1, 1994

By Scott Jones, Tony R. A. Durkac, David W. Stephens

Williams Mine was considering spending a large amount of capital to install a pumping system underground to rid the mine of slimes; with the introduction of Delvo Stabilizer this challenge would be met. This paper will address the process to introducing the Delvo Technology into the Cemented Roddill Program. Some areas that were worked on included: testing of the mix design, bet dosage rate for an economical solution, temperatures at different levels of the mine, the amount of time needed once the grout was put to sleep, preventing plugs in the delivery system A controlled dosage that gave the Operator a 12 hour window of flowable material was developed and an added feature to the introduction of Delvo was also noted; an increase in MPa strength over the design. Collectively with the help of operators at the batch plant and the underground miners involved with the program all concerns where addressed and all goals met. A cost effective program was implemented thus increasing productivity, preventing costly plugs, and improved the actual maintenance on the entire delivery system, which included the batch tanks, aggitator tanks, all pumps required in the system and of course reducing buildup of slimes at the cones.

Jan 1, 2001

By Claus Becker

Waterbearing, cohesive or non-cohesive grounds with glacial stone deposits are found very often in Europe. The problem consists of destroying the boulders and supporting the face simultaneously. At the example Grauholztunnel Bern ( outer diameter 11,60 m ) the theoretical attempt of solutions for the big machines is described: destroying of the boulders with roller discs, hydraulical support of the front. The problem of coming out of stones of a certain size from the surrounding matrix will be discussed. Further diminishing to the size that can be handled by pumps is executed by a crusher, situated in the center of the machine. At the same example the theoretical attempt for headings in cohesive soil with stone deposits are shown. Surface structure of the cutting wheel and working chamber as well as controllable current movements are the solution here. The danger of clogging discs and stone crusher has to be encountered by right positioning of the tools and jetting nozzles. At the example Sewer MoosstraBe Salzburg the same problems are discussed for the Mikro-Tunnels. The pipe-jacked sewer lines have outer diameters from 485 and 805 mm. With this method, the stones have to be holed through. The wear of the cutting tools determines the [ ]

Jan 1, 1989