Search Documents

By H. Lind

The consumption rate of Estonian oil shale increases due to the growing rate of exported oil-shale oil. Estonian oil shale active resources in working mines are predicted until the year of 2025 when the consumption rate stays at the level of 12 tons per year. If the consumption rate stays at that level, new mines should be opened after 20 years, if the rate increases new mines should be opened even earlier. The predicted active resources in Estonian oil shale deposits are calculated for 60 years, based on the parameters of the power station technicoeconomics. As a result, there is a need to open new mines. One of the potential areas for surface mine is the Tammiku-Kose prospect area (Rheinbaun Engineering, 1996).

Jan 1, 2006

By D. Duvris

The main objective of this work was to quantitatively investigate exhaust emission levels relative to maintenance (service) intervals during the operation of diesel-powered equipment at an underground bauxite mine in Greece. Such emissions depend on a great number of parameters, including the type of engine (technology) and its tuning, the type of work performed (as related to the engine workload), the suggested maintenance intervals, the altitude, the temperature and humidity of the atmosphere in the underground mine, the properties of the fuel and the operator's training and experience levels. The necessary ventilation quantities were calculated based on exhaust gas-concentration measurements and site-specific relationships between pollutants and adjusted air-quality indices. Diagrams comparing the necessary and recommended airflow for several equipment groups, featuring two engine types and different maintenance intervals, are presented.

Jan 1, 2000

By F. L. Wilke

A model is presented to minimize the winning costs per shift within the different sections of a potassium mine by liner programming and to simulate the other areas to get all costs in order to comp re different production strategies. he model is based on a a given total layout of the underground mining which is considered to be fix during the planning period. Room-and-pillar mining is assumed to be used. Potassium extraction is done by drilling and blasting. Transportation of the raw material to sectional crushers is done by scoop-trams where it is crushed to coarse-grains which allow further transportation by conveyor belts to the hoisting shaft or to a bunker. When production is stopped, the continuously working factory is supplied by means of this bunker. Starting from a desired composition of the raw material the model has to keep the given total. demand of raw material per shift, to minimize the winning costs, to keep the capacity constraints of the equipment and to determine the planned output of production of the sections per shift. Costs of the areas which follow the extractions are added to extraction costs in order to allow a comparision of costs of several alternatives of production. Optimization in extraction and assignment of scoop-trams to sections is done by linear programming. The other areas of the mine are treated by simulation. The model output is a schedule of the calculated costs broken down into costs of processes, equipment, and kinds of costs. This proceeding enables to compare different ways of production.

Jan 1, 1979

By G. Belardi, G. Marruzzo, P. Plescia

This paper presents the results of grinding tests performed on magnetite from Kiruna (Sweden) and on chromite from Skoumtza (Macedonia. Greece). Stresses were measured by XRD, which determined the variations in the characteristic structural spacings of the minerals both before and after, grinding in a HSM/250 Herzog laboratory ring mill. Anal Isis of the magnetite and c hromite crystallinstallin was performed hi measuring the broadening of the strongest diffraction peak (311). .Also, structural analysis on chromite was carried out using the Mikheev model. Ultrafine-grinding tests on the magnetite and chomite demonstrated that this type of treatment can induce profound variations m the surface-stress state. These included plastic variations of the cell followed by "chemical" stress with oxidation front the stricture to form hydroxide or carbonate, films. This can have a great influence on the mineral reactivity to flotation reagents

Jan 1, 1996

By S. Lin, Y. J. Wang

Fan stall is a notorious phenomenon of axial flow fans. When multiple fans of this type serve a ventilation system, their mutual impacts on the stability of the ventilation system are very complicated and not well understood. Results from laboratory experiments indicated that, when a fan is working across its stall zone (i.e., the pronounced trough on the fan characteristic curve), some branches in the system may suffer abrupt and even drastic changes in air quantity and pressure. The quantity range of the fan that causes the abrupt change is called an unstable operating range. The corresponding quantity range of a branch is called a nonachievable quantity range of the branch, because any quantity within this range cannot be achieved without changing some parameters of the ventilation system (e.g., branch resistances). This paper discusses these important characteristics of ventilation systems by using results from tests on laboratory tubing networks.

Jan 1, 1998

By Taehong Kim, Changsoo (Kevin) Moon, Anil Parikh

"This paper presents an overview and performance evaluation for a reconditioned decades aged open type hard rock TBM utilized for the twin running tunnel excavations of the Second Avenue Subway Project in Manhattan, New York. The TBM tunnel lengths are approximately 2,370 m (7,800 ft, east TBM Tunnel) and 2,190 m (7,200 ft, west TBM Tunnel) with a 6.7 m (22 ft) bored diameter. This “senior” TBM mined through metamorphic rocks consisting of schist, granofels, and pegmatite, and encountered various adverse geological structures, including some relatively heavy groundwater inflows. The ground support was generally pattern friction rock bolts, and steel sets were used in poor ground. This paper presents TBM characteristics and the subsequent performance, such as machine utilization, downtime, cutter consumption rate, net penetration rate, and daily advance rate. Machine operating parameters including thrust, torque, gripping force, and cutterhead RPM, are compared with various accompanying ground conditions. The performance changes between the adjacent tunnel sections are also presented. INTRODUCTION Project Overview The Metropolitan Transportation Authority Capital Construction (MTACC)’s Second Avenue Subway (SAS) Program consists of four (4) phases from 125th Street to Manhattan Battery Park along the 2nd Avenue (see Figure 1) in Manhattan New York. As a part of Phase 1, Contract 1 was awarded to S3 JV (Skanska/Schiavone/Shea) to build a TBM launch box and subsequent twin TBM tunnels from 92nd Street to 63rd Street under 2nd Avenue. Contract 1 was one of the key contracts in Phase 1 to pre-excavate through the footprint of the follow-on underground stations (72nd St. Station, 86th St. Station, and 96th St. Station) by hard rock TBM excavation. The project team included Client MTACC, S3 Tunnel Constructors, Designer, Aecom-Arup JV, and Consultant Construction Manager, Parsons Brinckerhoff. The major elements of Contract 1 included construction of TBM Launch Box supported by secant pile and slurry walls and mining of twin TBM tunnels with a combined tunnel length of approximately 4,560 m (15,000 ft). The dimension of the TBM launch box was approximately 247 m (810 ft) long from 92nd Street to 95th Street, 21 m (70 ft) to 24 m (80ft) wide along the 2nd Avenue, and 18 m (60 ft) to 21 m (70 ft) deep from the ground surface. The launch box was later used for the follow-on 96th Street Station."

Jan 1, 2016

By S. Saklar, i. Bayraktar

The effect of the feed size distribution on the kinetic parameters in pyrite flotation was studied. The kinetic parameters of the particular sizes were determined as a function of whether other particle sizes were present. From the data, a relation between the pyrite flotation rate and the particle size distributions was obtained. It was shown that the flotation rate constant (k) is a function of the size modulus (dt) of the Gates-Gaudin-Schuhmann distribution, and its variation may be expressed as k = a • exp(b . d,) for either individual size fractions or composite feed. Parameters a and b are dependent on the particle size distribution of the feed. Specifically, parameter a increases linearly as the distribution becomes coarser. The above relationship was also tested under conditions in which the collector (KAX) dosage was varied from 130 to 278 g/t. It was shown that the established relation was not dependent on the collector dosage.

Jan 1, 2002

By W. J. Deutsch, W. J. Martin, R. J. Serne

At the termination of mining, the quality of ground water in the ore-zone aquifer must be returned to a condition predetermined by the permitting agency. To immobilize the redox-sensitive elements (e.g., uranium, arsenic, selenium, molybdenum), it has been suggested that a reducing agent be circulated through the leached ore zone. We have conducted laboratory experiments to test the ability of sodium sulfide as such a reducing agent. Sodium sulfide lowered the redox potential of the effluent such that insoluble minerals containing the redox-sensitive elements should be stable. The uranium concentration of the solution decreased by more than three orders of magnitude. In column experiments, by the time 10 pore volumes of the sulfide solution had flowed through, sulfide minerals were forming. The experimental results indicate that the addition of sodium sulfide should cause chemical reduction of the leached sediments, thereby producing long-term stability of the ground-water/sediment system.

Jan 1, 1988

By D. McCarthy

This paper discusses the process involved in developing an optimum method of treating and removing heavy metals from water that have leached out from the native rock -prior to discharge back into the environment. Also designed into the system is a manner to stabilize the metals removed as a precipitate, so that they can be disposed of as a non-hazardous waste.

Jan 1, 1992

By J. Bigu

A theoretical radiation mine model, suitable for underground uranium nines, has been investigated. In this model, the rate of ventilation and/or the radon (thoron) gas emanation from mine walls are time-dependent. Several cases of practical interest have been investigated including sinusoidal, linear, exponential, stepwise, or a combination of two or more of the above. Analytical solutions were obtained for the time-dependent radon (thoron) gas emanation rate. However, because of the extreme analytical complexity of the solutions corresponding to the time-dependent ventilation rate case, numerical solutions were found using a special Runge-Kutta procedure and the Hamming's modified predictor-corrector method for the solution of linear initial-value problems. The mine model makes provisions for losses of radioactivity, other than by ventilation and radioactive decay, by, say, plate-out on mine walls, and by other mechanisms. Radioactivity data, i.e., radon, thoron, and their progeny. obtained with the above mine model for a number of ventilation and emanation conditions, are presented. Experimental data obtained in an inactive stope of an underground uranium mine for a time-dependent air flow case are shown. Air flow conditions (ventilation rate) were determined by tracer gas techniques using SF6.

Jan 1, 1987

By R. E. Miller

Hoisting coal using water and air is a technology which has potential to improve the economics and safety of transporting coal. The Coal Air-Lift Hydrohoist is a prototype coal hoisting system developed by the U.S. Bureau of Mines (USBM). This paper discusses the method used to regulate the supply of water to the 50-m-high hydrohoist U-tube such that the pressure difference at the bottom of the U-tube is held constant. Maintaining a constant pressure difference results in a steady flow of slurry out of the hydrohoist.

Jan 1, 1995

By G. S. Adisoma

To address the problem of grade estimation in a general three-dimensional shape and the uncertainty associated with the estimate, the technique of jackknifing/block kriging short-cut is proposed. A new estimator called jackknife kriging is introduced first. Through the jackknife variance, a confidence limit for the reserve grade estimate can be calculated. Unlike the kriging variance, which is more a measure of data configuration and is independent of data values, the jackknife variance reflects the true variability of the data. This approach provides a simple way to set a confidence level for global estimation of resources.

Jan 1, 1995

By R. Kadeg, S. Pavlou

A methodology for developing and utilizing risk-based action levels for soils in site closures is discussed. The methodology is based on standard exposure pathway models which are consistent with current regulatory guidance on conducting risk assessment. A simple approach to evaluating the potential for contamination ground water from the projected criteria based on the Toxicity Characteristic Leachate Procedure (TCLP) is also presented.

Jan 1, 1992

By F. Breu, R. Fraser, R. Lawrie

Diesel-powered underground mining equipment is generally accepted as the most productive, safest, and most efficient equipment used in underground mining operations. Widespread application of this equipment to underground mining is restricted, however, largely because of the difficulty of controlling the diesel engine exhaust emissions. This paper briefly examines control devices currently available for underground application, and also discusses the theory and mechanics of controlling diesel emissions with particulate traps and filters.

Jan 1, 1988

By Richard P. Killmeyer, Carl P. Maronde, W. W. Wen, Peter J. Suardini

Under a cost-shared Department of Energy contract, awarded as part of the Coal Preparation Program&apos;s High Efficiency Preparation subprogram, Custom Coals International will be installing and testing a 227 kglhr micronized-magnetite cycloning circuit in PETC&apos;s Coal Preparation Process Research Facility. The project includes the design, construction, testing, and decommissioning of a fully integrated circuit complete with feed coal classification to remove the minus-30-micron material, dense-medium cycloning of the 300 by 30 micron feed coal using micronized magnetite (<10 microns), and medium recovery via drain & rinse screening and various stages and types of magnetic separation. This paper will describe the micronized-magnetite beneficiation technology and the scope of work for this project including an update on the status of the project, the circuit, and the proposed test plan.

Jan 1, 1995

By Carlos E. Avila, Ronald D. Evans

The results of an experimental research program to measure the non- Darcy flow coefficient as a function of temperature and overburden pressure are presented. The experimental values of the non-Darcy flow coefficient were measured over a temperature range of 70-200°F (21°-93"C)and overburden pressures of 1000-4000 psia (68-272 atm). The data obtained confirm that the non-Darcy flow coefficient is a function of rock and fluid properties and is not solely dependent upon the former has been routinely assumed in the literature.

Jan 1, 1986

By D. Lynn, D. Arthur

Infrastructures continue to age and drinking water supplies are becoming scarce in the San Fernando Valley of Los Angeles, California. Frontier-Kemper Constructors, Inc. (FKCI) was engaged by the Los Angeles Department of Water and Power (LADWP) to complete the River Supply Conduit Improvement Upper Reach—Unit 7 Project (RSC7). Two tunnel sections were bored using a 2.64 meter diameter Microtunnel Boring Machine (MTBM) and a 4.12 meter diameter Earth Pressure Balance Tunnel Boring Machine (EPBTBM) to excavate approximately 3,733 meters (3.7 km) of tunnels through highly abrasive late-Pleistocene-age Quaternary alluvial deposits (Old Alluvium) and Holocene age Young Alluvium deposits above the water table. This paper discusses the challenges encountered managing the TBM’s equipment degradation, use of soil conditioners, cutterhead wear, torque and advance rates while maintaining the necessary face-pressures and parameters to limit over excavation and ground settlement.

Jun 13, 2021

By C. Garcia, H. Arias, J. D. Miller, C. L. Lin

The question of ultimate recovery in heap leaching operations is always of particular concern with respect to economic considerations. Of course the particle size distribution is a critical factor which determines ultimate recovery and which must be established based on a balance between the extent of mineral exposure and transport phenomena. Now it seems that the ultimate recovery for a given particle size distribution can be established from mineral exposure analysis by x-ray microtomography (XMT). Using recently developed software, micro-CT data can be used to determine the fraction of mineral exposed and thus the ultimate recovery. Examples of mineral exposure analysis are given for the copper heap leaching operation at Zaldivar, Chile.

Jan 1, 2002

By L. E. Krys, K. D. Harrison, C. G. Anderson

Since 1984, nitrogen-species catalyzed pressure leaching has been utilized at Sunshine Mining and Refining Company for the recovery of precious metals from a refractory sulfide concentrate. The process operates without the use of cyanide. The plant is now the only industrial-scale commercial application of this technology. Since the inception of the process, changes have been implemented to improve efficiencies and throughputs. Two of these changes, the replacement of nitric acid by sodium nitrite and a concentrate regrind, have recently been implemented. This paper discusses the development and potential mechanisms involved in these recently patented plant-process changes. A companion publication (Anderson et al., 1996) covers the plant integration and potential applicability of the technology.

Jan 1, 1997

By Michael J. Virnig, Kathryn C. Sole, Murdoch W. MacKenzie, Michael R. Davis

A solvent-extraction process has been developed for the removal of copper cyanide complexes from aqueous copper/gold cyanide solutions formed in gold-recovery circuits that treat ores containing cyanide-soluble copper. The process uses LIX® 7820, one of the LIX® 7800 reagent series developed by Henkel. It is based on a mixture of Aliquat® 336, a quaternary amine, modified with an alkylphenol, 4--nonylphenol. Extraction and stripping data for the base metal cyanides and thiocyanate are presented. Methods for the recove1y of copper and cyanide from the upgraded strip liquor are reviewed. A flowsheet based on this chemistry and a preliminary economic evaluation of a solvent-extraction circuit combined with the cyanide-recovery process developed by Metallgesellschaft Natural Resources (MNR) are also presented.

Jan 1, 1999