Search Documents

By X. Wu, M. Karfakis, E. Topuz

The generalized ventilation network problems encompassing both natural and controlled splitting networks, is formulated using a nonlinear nonconvex programming model, which has not yet been solved satisfactorily. This paper presents a methodology which can deal with the problem. The proposed methodology converts the nonlinear problem into a linear problem, by using special ordered sets of variables, and optimizes it by a modified branch and bound technique. The global optimality of the methodology and its applicability to different cases are investigated

Jan 1, 1991

By A. Pavlides

The purpose of this study is to compare estimation methods for lignite reserves at the Amyndeo mine and to provide a map of the estimated thickness of the coal seams. The reserves are first estimated with the method of Voronoi diagrams, using a group of mirror points to close the polygons around the boundaries of the mine. The second estimation method is based on Ordinary Kriging using the Spartan variogram model. Finally, the reserves are estimated by the mean lignite thickness value of the drill-hole data Two data sets are investigated. The first one corresponds to an exhausted part of the mine. The derived reserves estimates are compared with the actual data obtained by the Public Power Corporation (PPC) to validate the analysis. The second data set extends over the entire mine, and it is used to derive an approximate estimate of the total lignite reserves. A geostatistical analysis of the total layer thickness is performed. An interpolated kriging map of the total thickness variation is produced accompanied by a map of the kriging uncertainty.

Jan 1, 2008

By Li. S. D., R. X. Zhang, K. M. Li, Y. D. Zhang, Y. J. Hou, S. G. Li

A computer aided design software system for long range coal surface mine planning has been developed by the authors. The system is composed of two subsystems: a coal deposite sub- system and a long range mine planning system. The geological parameters are estimated and a grid model is formed, then a 3-D block model can be developed for mining design. The long range surface mine planning system is based on oriented graph simulation and combined approaches to seek for the optimal deign alternative. This mining model consists of a number of sub-models to realize mining design functions such as: calculation of mining volume and coal quality by graph scanning; determination of operational stripping ratio by interactive design; varification of annual coal production; delimitation and development of dumping site; optimization of material flow direction and volumes by Linear Programming; surface mine production scheduling by interactive iteration; etc. The software package was developed on PC computer 486. It features classified menu guide, module structure, figure and graph representation on the screen and flexible interactive functions. This system has been applied to an open cut coal mine and predicted functions have been obtained.

Jan 1, 1996

By Qing Wang

A longterm overburden removal plan can be realistic and optimum only when the cost and capacity profiles off the equipment assigned to the operation are taken into consideration. Therefore, the planning should involve the proper assignment of equipment capacity by insuring a timely investment and a timely replacement policy throughout the mine life. A dynamic solution algorithm has been developed, by which all possible truck fleet alternatives are evaluated for each year off the operation. Cumulative cost off the operation is carried throughout the analysis. The optimum solution is obtained by selecting the minimum cumulative cost at the last year and tracing backward the best fleet alternative for each year. The solution provides: 1. the optimum amount of overburden to be removed each year; 2. the best fleet to be assigned to the job; and 3. the best equipment replacement policy.

Jan 1, 1989

By Niall Weatherstone

Introduction Risks & Rewards of a Mineral Reserve Life History of a Mineral Reserve Estimate Risk Assessment & Management Mineral Resource & Reserve Estimation Good Practice Mineral Resource & Reserve Reporting Conclusions

Jan 1, 2003

By N. L. Piret, R. J. Wesely, A. E. Melin, A. D. Zunkel

At the end of the sixties new iron precipitation techniques as jarosite, goethite or hematite brought about the new generation of electrolytic zinc plants, thereby terminating the multitude of existing neutral leach residue treatment schemes. Since the eighties, increasing environmental impact considerations urge the conversion of these contaminated waste generating precipitation processes to techniques which either produce environmentally acceptable residues or minimize their formation thereby generating iron-bearing byproducts. Technologies identified and economically assessed include the hematite process either suitably improved or with subsequent upgrading, the iron extraction process and the direct smelting of neutral leach residue to slag and fumed zinc oxide.

Jan 1, 1993

By Sergey G. Pushkin, Eugeny L. Schastlivtsev, Anatoly A. Bykov

Three years ago the authors and a group of assistants began to develop a GIs-system for integration of comprehensive eco- logical information to be linked to geographical maps of Kuzbass region. And now we have got the working system and some first results that the present paper deals with.

Jan 1, 1996

By Luis Fernandez-Deza, James Hawn, Dustin Mount, Jean-Marc Wehrli

The RiverRenew Tunnel System project in Alexandria, VA forms part of a CSO scheme aimed at reducing overflows of combined stormwater and sewage into the Potomac River during storm events. A major piece of the project is a 12-foot internal diameter tunnel of approximately 12,000 feet length lined with a single-pass precast concrete segmental liner and excavated by an Earth-Pressure Balanced Shield TBM. The tunnel lies between 120 to 140 feet below grade in the clays of the Upper Potomac Formation with occasional dips of more granular, saturated soils of the Terrace Formation and the Alluvium. The TBM is launched from a figure-8 configuration Pumping/Screening Shaft located within AlexRenew’s operational Water Resource Recovery Facility. This paper discusses the challenges encountered during the launch of the TBM in short mode within a highly congested site and from narrow deep shafts.

Jun 13, 2023

By Aladar B. Dory

INTRODUCTION Practical experience in mines with known presence of radon daughters in the mine atmosphere in Canada and elsewhere shows that a very high concentration builds up in an unventilated dead end heading. As Holaday et al1 observed, even a minimal air movement results in a drastic reduction in radon daughter concentration. It is therefore obvious that the main objective of radon daughter control in the working environment is to design the ventilation system providing an optimized flow of fresh air into the workplace, resulting in acceptable climatic conditions and achieving radon daughter concentrations resulting in exposures as low as reasonably achievable. BASIC OBJECTIVES Large mining companies, having extensive material resources and professional expertise, have utilized elaborate electrical modelling in the design of mine ventilation systems as early as 1950 (coal mining industry in Europe) and with the advance of computer modelling techniques, their utilization in ventilation systems design is on the increase. Unfortunately, these methods are usually not available to small mining companies and even the large companies might not achieve the fullest benefit from utilizing them, if proper limiting factors are not considered in the modelling. When an evaluation of a ventilation system of a mine is undertaken in literature, a measure of the amount of air supplied underground per one ton of ore mined is used as an indicator of the efficiency of the ventilation system. Yet, even the greatest amount of air forced into the mine might not result in an acceptable working environment if a proper distribution of this air into individual working places is not achieved. The volume and the age of the air are probably the two most important factors in achieving acceptable radon daughter concentrations in the workplace, but other factors also have to be considered. DIRECTOR MINE - ALCAN, NEWFOUNDLAND FLUORSPAR WORKS ST. LAWRENCE, NEWFOUNDLAND, CANADA Ventilation To illustrate the effects of the design of the ventilation system on the control of radon daughter concentration, let us review the gradual development of the ventilation system of this mine from the earlier years of its development up until its final years of operation. This mine, located near the community of St. Lawrence on the south coast of Burin Peninsula was developed in the late thirties and reached full production by 1942. Unfortunately as was customary at that time, the only source of ventilation was a natural draft. The mine was extremely wet, and no significant attention was initially given to possible health effects of dust. It was not until the mid-fifties, when a number of cases of silicosis had surfaced, that de Villiers and Windish2 observed a significant increase of lung cancer incidence among the miners in comparison to its incidence among the general population of Newfoundland. Suspicions regarding radiation as a cause of the lung cancer were expressed, but it was only in surveys taken in late 1959 and early 1960 that Windish3 and Little4 established the presence of radon daughters in the mine atmosphere in very high concentrations. Windish, de Villiers and Hurley suggested that the most likely source of the radon in the mine was the mine water which dissolved radon during its passage through the granitic country rock in the surrounding geological area. This conclusion was confirmed by analyses of water from various areas of the mine by the Atomic Energy Canada Limited laboratories. The radon values in the samples varied from 4,240 to 12,850 pCi/L5. Following the discovery of the presence of radon daughters in the mine, the company took speedy action to install mechanical ventilation for the mine. The system was not designed as a total unit, but fans were installed rather on a trial and error basis. The basic system installation began in March 1960 and was completed by 1962. It remained basically unchanged with only minor modifications until August 1973 when a wholly new, redesigned ventilation system was implemented. A schematic section of the mine and its ventilation system for the period prior to March 1960 is given in Figure "A", for the period 1960-1973 in Figure "B", and for the period after August 1973 in Figure "C". The ventilation system prior to 1960 is not known. All workings of the mine were ventilated only by natural ventilation. If any measurements of airflows at different or any times of the year ever existed, no records have been preserved. The very minimal natural ventilation was augmented by "blowing" air from compressed air supply lines and exhaust air from drills. It is known that the compressor capacities of the mine were limited and therefore no significant air movement was probably created by the "blowing".

Jan 1, 1981

By S. P. Banerjee

There has been a phenomenal increase in production of coal from opencast mines in India. At the same time environmental problems caused by mining are receiving greater atttention. Deterioration in ambient air quality due to increased concentration of suspended particulate matter (SPM) in and around an opencast project is a major problem. Some measured values of SPM level around opencast mines in diff coalfields show that in many cases the TLV of 500 ug/m^3 is exceeded. The impact of dust emission from a mining project on surrounding areas are estimated by using computer models for air pollution dispersal but such treatment suffers from errors in predicting the dust load and failure to take into account the terraced nature of the opencast mine site. The haul roads have been identified as the most prolific source of dust and some recent trials on haul road dust consolidation in Indian mines are mentioned in the paper. Statistics regarding pneumoconiosis cases in Indian coal mines for the last decade are presented to show an increase in reported cases and a gist of the recently amended regulations on the subject of precaution against dust is mentioned.

Jan 1, 1991

By Yiyin Ma, Yuqi Chen

Based on two in-situ measurements and mathematical analysis, the micro-climate in a large central underground pump and power station has been discussed in this paper. It is found from the research that the "semi- infinite" body model in the general heat transfer can closely represent the heat exchange process in the air flow-surrounding rock-adiabatic intermittent heat source complex in the station. Finally, computer simulations were made to calculate the micro-climate in a similar pump and power station where power machines operate intermittently. The simulation results are quite satisfactory. It can provide useful information for decision- making in the air conditioning of such stations.

Jan 1, 1991

By A. Giblett, J. Shuttleworth, R. Dunne

In a previous paper (Dunne, Martins, Goulsbra, Chittenden 1997), the new gravity circuits at Telfer Gold Mine, which incor­porate Knelson centrifugal separators in both the sulphide and oxides, are described. The advantages of the new circuits over the replaced spiral ( oxide circuit) and jig (sulphide circuit) were discussed, as were the improvements in gravity gold recovety. It is of note that the installation of the centrifugal separators in themselves did not result in increased gold recovery. The realisa­tion that changes in gold room practices are required to take advan­tage of the increased fine gold recovery from the Knelson concen­trator was an important step towards improved gravity gold recov­ery. This was achieved by increasing the time taken to treat the Knelson concentrate on the shaking table in the gold room. Although this increased gold recove1y, it was found that the table tailings, especially from the sulphide circuit, still contained high values of gold. In an effort to ascertain ways in which gravity gold recovery could be fu1iher improved, a sample of the sulphide table tailings was sent to the Oretest Laboratory in Perth for testwork. The results from this program are discussed in this paper.

Jan 1, 1998

By Keith G. Wallace, Malcolm J. McPherson

In order to model accurately a mine ventilation system in an existing mine, it is necessary to determine the resistance to airflow in all main airways. This is accomplished by measuring the airflow and pressure differential in each airway. Gauge and tube methods have been used to determine pressure drops in ramps and level airways. However, it has rarely been used in evaluating the frictional pressure drop in shafts. Because shafts commonly have the highest pressure loss in mines, it is critical that the resistance of these airways be determined accurately. This paper describes the theory and practice of using the gauge and tube method for determining the pressure drop in shafts. The pros and cons of using this method are discussed as well as a comparison between the gauge and tube and barometer measurement techniques. Case studies showing the accuracy of shaft gauge and tube measurements are also presented.

Jan 1, 1991

By Fred L. Stanley, Ricky Q. Honaker, Michael J. Mankosa

Spiral concentration has gained a great deal of popularity as a cheap, effective method for recovering fine coal (8x100 mesh). Typically, 6-turn, wide-profile spirals are used in either a single pass, open- circuit configuration or in combination with a middlings retreat circuit. Recent work conducted at Carpco, however, has indicated that a split feed scenario and/or hydraulic classification in advance of spiral concentration offers significant advantages in both capacity and metallurgical performance. In addition, it has also been shown that the apparent density separation which naturally occurs in a hydraulic classifier provides significant up-grading in terms of pyrite and ash rejection. The results from this study will be presented in comparison with those obtained from open-circuit spiral testing.

Jan 1, 1995

By K. C. Shaver

The Sloan Ranch kimberlite complex is located approximately 130 km north-northwest of Denver in the Precambrian core of the northern Colorado Front Range (Figure 1). A Devonian age for the complex is suggested by the fossil assemblages in limestone xenoliths (Chronic and others, 1969), and by paleomagnetism of the kimberlite (E. E. Larson, personal communication, 1986). The presence of diamond was first reported in rocks from the Sloan diatreme by McCallum and Mabarak (1976). Prior to this time, the distinctive- appearing host rock of the Sloan diamonds had been quarried for use as terrazzo stone; examples may be seen in the floors of the airports in Cheyenne and Laramie, Wyoming. The Minerals Division of The Superior Oil Company obtained a lease on the Sloan property in 1980. During the next four years Superior built and fine-tuned a highly efficient diamond recovery facility, explored and tested the Sloan deposit, and used Sloan as a site for testing numerous exploration techniques for future use in a continuing exploration program in the Colorado-Wyoming kimberlite province. The Sloan property was ultimately determined to be sub- economic, but the lessons learned there have been very helpful in subsequent exploration efforts.

Jan 1, 1987

By P. H. Lu, M. J. DeMarco, J. R. Koehler

Beginning in late 1985 and continuing through 1987, US Bureau of Mines personnel investigated longwall chain pillar and entry design in two and three-entry gateroad systems at a deep underground coal mine in central Utah. To evaluate their respective stability characteristics, four chain pillars and two longwall panels within the two separate entry systems were instrumented with Bureau hydraulic borehole pressure cells to continuously monitor vertical and horizontal pillar and panel stresses through adjacent panel retreat. In addition, supplemental entry closure information was obtained from sites located in the vicinity of the instrumented pillars. The findings presented in this report demonstrate the practicality of evaluating mine pillar stability using in situ methods and support three significant conclusions regarding ground control aspects of the investigated two-entry system: (1) Total areal entry loading was considerably less for the two-entry system, as opposed to the three-entry system, (2) a smaller percentage of opened ground in the two-entry system contributed to a marked reduction in rooffalls, and (3) lower areal loading in the two-entry system suggests improved ground conditions when mining the underlying seam.

Jan 1, 1987

By R. L. Teseneer

Pyrite samples from twenty-one locations in the North Carolina Slate Belt were analyzed for cobalt, gold, mercury, and nickel by atomic absorption spectrophotometry. The geographic distribution of relatively high values of certain trace elements in pyrite suggests that, in addition to gold, cobalt and nickel metallogenetic provinces are possible in the slate belt. Northwest trends of province boundaries may be genetically related to subsurface features rather than to surface geology. Within province boundaries gold and nickel exploration programs should be concentrated in areas containing intermediate to mafic tuffs, while cobalt may be more concentrated in argillites and phyllites.

Jan 1, 1979

By Peter P. Harvey

The Nonel Primadet is a non-electric blasting initiation device. The system incorporates the safety advantages of a cap and fuse system with the precision blasting afforded by electrical blasting caps. Each unit is made up of a delay blasting cap factory-crimped to a Nonel® shock tube lead line. The delay elements in the blasting caps are manufactured in both millisecond and long period series. There are 16 periods available in both series - period 0 through period 15. The units are manufactured in 12', 16', and 20' lead lengths. The hollow shock tube is made of surlyn plastic and it is coated on the inside with a reactive material. The powder train has a density of only 1/10 grain per linear foot of tube. A typical blast round is timed precisely the same way it would be with electrical caps. After the round has been timed and loaded, the tube leads are gathered in convenient bunches and tied into a detonating cord trunkline. The Nonel® tube bunches are initiated by the output of an 18 grain per foot detonating cord trunkline. Once initiated, the Nonel® shock tube will reliably propagate at 1800 meters per second. The energy from this shock front initiates the delay elements in each delay cap. The shock tube is inert to electrical energies, including; stray current from AC/DC power sources, as well as, electrostatic discharges. The tube is also inert to initiation by impact. The system has proven to be particularly advantageous in both tunnel and shaft blasting applications. The major advantages in using the Nonel® system in this type of work are: 1) faster and easier tie-in techniques through the use of bunch-blasting. 2) electrical power can be left on during loading and tying-in. a. electrical lights can be turned on at the working face - better lighting facilitates loading and tying-in. b. electrical pumps can continue to function throughout loading and priming procedures (this is particularly advantageous in shaft work with water problems). 3) down-time due to approaching electrical storms is minimized. 4) increased overall efficiency in the blasting cycle: a. it is easier to train a man in the proper use of the system. b. fewer missed holes per round. c. less time required for tie-in. 5) safety-advantage--The system is not susceptible to involuntary initiation from extraneous electrical energies.

Jan 1, 1979

By P. M. Jones

Introduction The success of in situ leaching depends upon: • maintaining adequate injection and recovery flow capacities in wells, and • distributing leach solution effectively to contact and leach ore minerals within the target zone. Solution balance is an important indicator of the capability of a particular in situ hydrologic design to efficiently and effectively control and distribute leach solution within the target ore zone. As part of ongoing hydrological investigations into in situ leaching, the US Bureau of Mines (USBM) is studying factors affecting solution balance in an unsaturated copper ore deposit at the Cyprus Casa Grande Mine. The purpose of this study is to assess the effect of hydrogeologic features and in situ operating conditions on changes, during leaching, in: • solution storage within the deposit, and • solution balance. At the Casa Grande Mine, In-Situ-Leaching Test Facility, solution balance estimates are obtained for 10 selected intervals during 17 months of leaching under a variety of well configurations, pressures and flow conditions. Operational and geological description The Casa Grande Mine is located 32 miles south of Casa Grande, AZ. The mining area is within the Casa Grande Deposit, a porphyry copper stock consisting primarily of an intensely-fractured, granodiorite cap overlying a copper sulfide base. As a result of mine dewatering activity, unsaturated conditions existed in the deposit prior to leaching (Schmidt et al., 1990; Friedel and Schmidt, 1991). No groundwater was present in any of the in-situ-leaching, test-facility wells after drilling and prior to leach solution injection. Also, no ground water seepage occurs in the test-facility drift. The Casa Grande, In-Situ-Leaching Test Facility consists of 58 injection and recovery wells collared in an underground drift. The wells were drilled at various angles into the granodiorite deposit in a series of 15 divergent fans (Fig. 1). The fans are 12.5 ft apart and lie parallel to one another between the 900- and 1100-level drifts. Each fan contains three to five wells drilled at angles ranging from 6° to 89° from the horizontal. The wells can operate in an injection or a recovery mode. Currently, 36 flow sensors and 28 pressure transducers (part of a hydrologic, data acquisition system) are used to continuously monitor injection-well flow rates and pressures.

Jan 1, 1993

By Robert D. Schmidt

The Bureau of Mines is conducting an investigation to develop remediation techniques for residential water wells whose yield has been affected in the long term, by underground mining. Initial work relating to this project was conducted in 1984-1987 at a room and pillar mine in Indiana County, Pennsylvania. Piezometer nest data from the room and pillar mine reveals that a downward gradient in piezometric head exists in shallow strata as a result of drainage into the underlying mine void. The vertical gradient in head in turn results in well bore leakage in open-hole water wells. The relative yield of valley wells is only slightly affected however because the high surficial recharge rate through fractures more than compensates for fracture leakage into the underlying mine. The relative affect of well bore leakage on well yield is greater in certain hillside and hilltop wells that have comparatively low inflow rates at shallow depths. The static water level of such wells is determined to a much greater extent by the chance interception of deep outflow fractures, than is the case for wells drilled in a more intensively fractured valley bottom. The lower static water level of wells that intercept deep fractures does not necessarily reflect the water table conditions outside of a small radius around the affected well. The results suggest that permanently isolating well bore outflow fractures may remediate certain open-hole residential wells that have been affected by high extraction underground mining.

Jan 1, 1986