Search Documents

By A. K. Sheik, W. G. Pariseau

A small underground mine in northern Idaho was used as an experimental facility for studying the role of water in the analysis of mine-opening stability. Laboratory test data, borehole measurements and geological mapping assisted in the construction of a coupled finite element model of the rock mass. The model was used to make quantitative estimates of rock stress, strain and displacement changes and to make estimates of the water pressure and flow velocity changes that occurred during historical mining. Stope cuts and wet fills were included in the analysis. The stability of the crown pillars between stopes was of particular interest. The relatively low effective stress and high rock-mass strength showed that water pressure changes were of no great consequence, which is in agreement with experience. The computational tools used in the analysis may be applied to other wet mines with appropriate changes to site-specific data.

Jan 1, 2002

By J. Tuzson, H. McL. Clark

Introduction Wear of pumps, wet cyclones and pipelines by suspended solid particles will impact their operating economies by limiting their useful life, reducing their reliability and increasing the amount of servicing. Erosion is considered a materials problem. The empirical solution consists of testing different materials in field applications. Such tests are time consuming and expensive. The prediction of localized wear rates, life estimates and appropriate material selection demand a better understanding of the slurry wear process in environments corresponding to those found in working equipment. Key words: Wear, Slurry abrasion, Coriolis erosion tester The slurry wear process Solid particles suspended in liquid generally move with the flow, but such particles deviate under the centrifugal and Coriolis forces encountered in pumps. The concentration of particles will increase, and a solid layer or bed may accumulate if the acceleration is directed against the flow passage wall. Large particles in dilute suspensions may impact the wall. dissipating their kinetic energies and removing material. However, particles smaller than about 11)(1 µm encounter great drag when moving through the liquid. and such par¬ticles have little kinetic energy left when they reach the wall. They cannot penetrate the stagnant boundary layers present in pumps. Therefore, small particles tend to form beds that slide along the wall, removing material by a process that could he called sliding erosion or wet abrasion. Wear by impact erosion from large particles in dilute slurries can he predicted by appropriate analytical and empirical methods. However, laboratory tests and calculations of wear rates that correspond to sliding erosion are more likely to correlate with field experience from wear under similar conditions. Specific energy Data from laboratory slurry erosion experiments have shown that the amount of material removed is approximately in proportion to the energy expended in the erosion process. Thus. the specific energy-energy expended in removing by erosion a unit volume of material-offers a simple, practical measure for the erosion resistance of materials. The concept was found to also apply to sliding erosion (Clark et al.. 1997). Generally, the study of the material-removal process in slurry erosion continues to remain a subject of research. Conceptually, if the flow velocities and accelerations could be calculated in a pump or pipeline, the energy dissipated at the passage walls could also be estimated, and the material removal rate would become known from the specific energy determined by laboratory tests. Slurry erosion testing Laboratory devices made specifically for slurry erosion testing may be grouped into the following: jet erosion devices, slurry pots and the Coriolis test machine (Pagalthivarthi and Helmly, 1992). Jet erosion devices use a slurry pump and nozzle to produce a high-velocity slurry jet that is directed at a flat material specimen, either perpendicularly or at some acute angle. Combined impact and sliding erosion are produced. but the processes cannot be separated, and the wear is difficult to assess except by weighing. Slurry pots consist of a cylindrical vessel containing the slurry of interest. In the slurry pot, test specimens are attached to a rotating arm. The samples are rotated in the slurry and experience local flow conditions that result in combined impact and sliding erosion. Wear depth measurements from detailed laboratory experiments have been successfully correlated with results from an analytical model of the process, and specific energy values have been calculated (Wong and Clark, 1995). In industrial use, the samples are weighed to determine the total material loss. Materials are ranked with respect to some reference material. The Coriolis erosion tester (Tuzson, 1984) consists of a rotor with a central cavity, from which two opposing radial passages lead out (Fig. 1). The slurry is fed to the centerof the rotor in one pass from a stirred overhead tank. The slurry particles are subjected to the Coriolis acceleration as they flow out through the radial passages. The material specimens are mounted into the radial passage walls facing the direction of rotation and are eroded by the particles that are pressed against them as they flow out radially. A narrow groove is worn into the sample within a few minutes, using a few gallons of slurry. Material removal is estimated accurately from profilometer traverses across the wear scar at different locations. The energy dissipated by the particles can be estimated, which leads to a well-defined experimental value for the specific energy.

Jan 1, 2000

By Andrew J. Neale, Brian C. Flintoff

A review of the current literature, combined with the authors' knowledge of the western Canadian coal industry, indicates that the development and implementation of process control in coal preparation, particularly in flotation applications, is significantly lagging behind that seen in mineral processing. The reasons for this include the lack of inexpensive and reliable sensors, incomplete understanding of the flotation process, limited experience of process control in the coal preparation industry and depressed coal prices, all of which have combined to hinder plant automation. This paper illustrates the benefits of process control in coal flotation, provides a general discussion of the control problem and concludes with two examples drawn from Australian experiences.

Jan 1, 1989

By G. Brien, O&apos

Selective in-plant breakage was investigated at a Central Queensland, Australia mine. Component seams and size fractions from in-plant samples were characterized petrographically and probability analysis of vitrinite reflectance data used to track the distribution of seam proportions through the plant. Results show that the 2 seams reported differentially to coarse and fine circuits, mainly as a function of coal type rather than rank. Seams were also preferentially concentrated in different size fractions of the coarse circuit. Breakage in the coarse coal centrifuge generated approximately 4% of -0.5 mm fines, but was not seam specific.

Jan 1, 1996

By John Mastoris, Kostis Dragasakis, Kostas Kouklidis, Shkurtë Gashi, Halil Berisha, Jenuz Bulica

Titan Group’s environmental policy and Sharrcem’s Corporate Social Responsibility (CSR) are the driving forces behind the development and implementation of a comprehensive Rehabilitation Plan at Dimce Quarry, which is the main raw material source for Sharrcem Cement Plant since the 1970’s, located in the municipality of Hani i Elezit in Kosovo. Based on an Environmental Impact Assessment Study and the approved Mining Plan and also on the principles prescribed in the Guidelines on Quarry Rehabilitation, released by the Cement Sustainability Initiative of the World Business Council for Sustainable Development (WBCSD-CSI), Sharrcem has adopted a quarry operation and rehabilitation process in line with the best practices in the mining and cement sector. This paper discusses the background for the development of the rehabilitation plan and the results of rehabilitation activities, as have been implemented over the last few years. The main objective of the progressive rehabilitation plan at Dimce Quarry is to restore the depleted pit and return it back to the original land owners for resettlement. To date approx. 3,4Ha of former mining area has been restored by backfilling and levelling of the depleted closed pit and returned back to owners, who have built their houses and turned it into a living area again. This Quarry has turned out to be a real composition and practical example of preserving and returning back the natural resources in a state compatible with the surrounding environment and with respect to the needs of the local stakeholders. The motivation for business to engage in rehabilitation activities in the first place lies in the belief that the development and implementation of a progressive and practical Quarry rehabilitation plan and restitution of the land will deliver significant environmental and social benefits that outweigh the long-term rehabilitation costs, while maintaining the company’s reputation.

Jan 1, 2017

By Robert F. Kaufmann

INTRODUCTION In response to the Uranium Mill Tailings Radiation Control Act (Public Law 95-604, Section 114c), a report has been prepared by the U.S. Environmental Protection Agency (1980) which describes the potential health and environmental effects associated with uranium mine wastes. The author was responsible for the geology, hydrology and aqueous pathways analysis portions of the report. All potential sources of contaminants, solids, liquids, and airborne emissions, which might cause adverse impacts upon the environment or health of nearby populations were considered. Wastes at both active and inactive uranium mines (Hans and O'Connell, 1981) are described and assessed with respect to dose and health effects (Blanchard et al. 1981). The emphasis of this paper is on the liquid emissions and the aqueous pathway. Model uranium mines were developed for surface and underground mines. The model underground mine was placed in New Mexico while the model surface mine was in Wyoming. Development of a generic assessment was complicated due to the inherent variability of uranium mines. Also, most information available relates to uranium mills rather than to mines, or reported measurements were often influenced (biased) by wastes from a nearby mill and did not specifically reflect mine discharges. Consequently, the assessment presented is often based on conservatve (maximizing) assumptions which are identified as such, and which were based on knowledge from field investigations, available literature, and consultations inside and outside the U.S. Environmental Protection Agency. Maximum use was made of available data, supplemented with limited field studies in Colorado, Texas, New Mexico, and Wyoming. PREVIOUS INVESTIGATIONS Stream survey work in Colorado by the Water Pollution Control Commission and the U.S. Geological Survey (Moran, 1974; Wentz, 1974) mentioned a portion of the Uravan Mineral Belt and uranium mines therein, but the work did not emphasize uranium mines. Significant amounts of acidity and total trace metal concentrations were found in streams from 18 different mining areas. Dilution and chemical precipitation below mine drainages decreased concentration and increased the pH. Given enough time and distance, the streams recover naturally, but the accumulations of trace metals in the sediments increase. Field observations in 1971-72 of streams in most of Colorado indicated that approximately 724 km of streams in 25 different mining areas were adversely affected by mine drainage (Wentz, 1974). Discussions of the impacts of uranium mining on water quality or quantity are incidental in numerous impact statements and environmental reports prepared by industry and (or) the U.S. Nuclear Regulatory Commission as an integral part of licensing or relicensing uranium mills. Coverage on mining is usually minor as the principal focus is on milling impacts. The same is true for the recently prepared generic EIS on regulation of uranium milling (U.S. Nuclear Regulatory Commission, 1979). Radiochemical assessment of surface and groundwater in uranium mining districts of New Mexico is done by self-monitoring programs associated with NPDES permits. Also, radiochemical assessment studies have been funded by the New Mexico Environmental Improvement Division and U.S. Environmental Protection Agency. Unfortunately, there has been no concerted effort to prepare broad assessments of the cumulative impacts of mining and milling in areas of interest in Texas, New Mexico, and Wyoming. Critical review and synthesis of these types of data can produce rather useful information. For example, the publication "Water Quality Impacts of Uranium Mining and Milling Activities in the Grants Mineral Belt, New Mexico" (U.S. Environmental Protection Agency, 1975) addresses the groundwater and surface water changes as the result of extensive uranium mining and milling production in a relatively confined area. A more recent report by the Wyoming Department of Environmental Quality summarizes 16 years of aqueous radium and uranium data. The study reports significant amounts of radium-226 and uranium were present in surface water in the Shirley Basin as a result of inadequate mine water treatment (Harp, 1978). In Texas, surface water and groundwater monitoring conducted by industry, as well as by State and Federal agencies, reveals little or no change of chemical quality attributable to uranium mining and milling (Gesell, 1977; Kallus, 1976). This conclusion is based on 586 samples collected from 198 stations over a period of 39 years, but primarily from 1961 to 1975. The State monitoring program by several agencies is continuing, but data reporting and interpretation is lagging. One survey (Itin, 1975) showed that none of the mine water from the 10 lakes that were sampled was suitable for human use. The lakes were also unsuitable for irrigation due to mineralization of the water by sulfate, chloride, and TDS. One of the 10 was suitable for stock watering.

Jan 1, 1981

By J. Lorosch

Improvement of current leaching technology was found necessary when processing ores which are more difficult to leach because they generate highly viscous, air-rejective pulps. Cyanidation of these pulps has to run at low oxygen concentrations if the conventional aeration technique with compressed air is used. Since the dissolution rate of precious metals mainly depends on the concentration of dissolved oxygen in the pulp [1, 4, 5], the kinetics of the gold extraction become slow in such cases, which in turn often leads to a significant decrease in the overall gold output within the conventional leaching time of up to 48 hours.

Jan 1, 1988

By Kenneth N. Weaver

Introduction and Historical Background State Geological Surveys have been deeply involved in industrial minerals from their inception beginning in the first half of the 19th Century. To Massachusetts belongs the credit of having carried out the first Geological survey under state auspices on the Western Hemisphere. One of the causes leading up to this survey was. Governor Lincoln's message to the legislature of May 29, 1830, from which I quote in part: "Much knowledge of the natural history of the country would thus be gained (from a geological survey), and especially the presence of valuable ores, with the localities and extent of quarries and of coal and lime formations, objects of inquiry so essential to internal improvements and the advancement of domestic prosperity, would be discovered.". Similar phraseology is present in practically all of the initial organic acts creating the first State Surveys. High on the list of priorities for these embryo surveys was an inventory of the mineral resources of the State with particular emphasis on the industrial minerals. Prom these early beginnings, the state surveys have developed a great wealth of geological data either directly or indirectly relating to the development of mineral resources. One can gain some conception of the effort that state surveys today place on industrial minerals studies by noting the projects in which they are engaged as reported in the State Geologists Journal. In 1970, for example, approximately

Jan 1, 1972

By R. Merwin, S. Hoff, A. Ellsworth, M. Zhao, X. Jiang

The choice of mill linings in comminution circuits is critical as it affects grinding efficiency, overall cost, and product quality. As a consequence, a variety of liners have been developed over the years in an effort to increase wear resistance, improve grinding efficiency, and reduce energy consumption. One particular type of metal magnetic lining (MML) was developed in China seventeen years ago and has since been installed in over 400 applications throughout the Chinese mining industry. Most recently, one set of magnetic mill liners was brought to the US for installation into a secondary ball mill used for the grinding of iron ore. Protection of the mill is provided through the magnetic attraction and retainment of worn media, ball chips, and other various magnetic particles to the mill wall. This greatly improves the wear resistance and overall life of the liner. The installation and performance data for the magnetic mill liners in a US iron ore concentrator are presented in this paper.

Jan 1, 2007

By V. Rajaram

A mine fire or roof collapse may necessitate the reversal of main fans to isolate the fire or provide an escapeway. Hence, to assist the mine operator in estimating the flow and pressure during reversal, Engineers International Inc. conducted a laboratory and field study of the reverse performance characteristics of main mine fans. Laboratory tests were performed using a 2.4-m (96-in.) diam vane axial fan to establish the forward and reverse performance characteristics under controlled conditions. Subse¬quently, a field test was conducted in a Colorado oil shale mine during which two 2-m (79-in.) diam fans were reversed. The data obtained indicate that reverse performance characteristics depend on the blade angle and the hub-to-tip ratio. The quantity in the reverse mode ranged from 30% to 65% less than in the forward mode, and the static pressure was directly proportional to the square of the quantity.

Jan 1, 1987

By John Armstrong, Michael Savill, David Powell

Hong Kong is an intensively developed region and has the highest vehicle densities in the world. In 2000 there were 6.6 million people and 580,000 vehicles using 1,890 km of road covering the 1084 km 2 territory. The high vehicle and population densities together with the difficult terrain have seen road tunnels emerge as key components both in the current and future road transportation network. Currently there are eleven operating highway tunnels in Hong Kong, seven government owned and the remaining four “build, operate and transfer” franchises, see Figure 1. The very first tunnel was the dual two Lions Rock Tunnel completed in 1967and the latest the dual 3 lane Tai Lam Tunnel opened in mid 1998. Figure 2 shows the alignment and statistics for all 11 Hong Kong tunnels. Looking ahead, Hong Kong has embarked on the study and design of the next generation of major highways and as many as a further seven tunnels are currently under feasibility study or detailed design. This seems an opportune year to produce a broad appreciation of the fire strategy, life safety and ventilation practices in Hong Kong not only for the existing tunnels but the new standards and requirements for the next generation of Hong Kong tunnels. This paper provides an overview of the fire strategy, life safety and ventilation of Hong Kong’s existing and planned tunnels. The paper pays particular attention to the areas where the unique conditions and requirements in Hong Kong impacts on tunnel and systems design and the solutions adopted to overcome these challenges.

Jan 1, 2001

By Marlin D. Schutte, Graham M. Fraser, Paul M. Kubera, Ronald J. Weetman

Mixers play an important function in the operation of multi-phase reactors in the minerals processing industry. They must suspend solids, transfer oxygen, maintain pH and temperature uniformity, assist in heat transfer, and, in biological processes, avoid the development of excessive shear rates. The LIGHTNIN A315 impeller (Figure 1) effectively supersedes the older Rushton turbine (Figure 2) which has been classically employed in gas­Iiquid-solids applications such as bacterial oxidation, cyanide destruction, etc. Since a stirred tank reactor can be such a key part of the overall process, it is essential that the mixers be designed for long term reliable operation, both process and mechanical, to insure a high percentage of on-line availability. Mixers in gas-liquid-solids processes may experience extraordinary loading conditions which must be taken into account to guarantee a robust mechanical design. Given the recent trend towards the design of world-class process units with maximum capacity equipment, there is increased importance and emphasis on the integrated design of the complete agitation system -mixer, vessel, and structure -to insure trouble free, post­commissioning performance. This paper presents some of the considerations necessary to specify the process functions of the mixer in multiphase applications, as well as special considerations for the mechanical design of the integrated reactor system.

Jan 1, 1993

By P. L. Yorio, D. R. Willmer

"The current paper presents the results of a study designed to explore the types of practices that are fundamentally important to developing and maintaining comprehensive risk-based health and safety management systems (HSMS) in mining organizations. Eighteen practicing health and safety (H&S) executives, managers, and professionals from a variety of mining commodities were asked to assess the fundamental importance of 20 distinct elements and 133 different practices assembled from a review of several HSMS consensus standards. The research approach assumes that developing and maintaining a robust HSMS requires unwavering attention to activities designed to either: 1) directly contribute to a risk management system’s plan-do-check-act cycle; or 2) build an organization’s internal infrastructure without which the cycle cannot be sustained. The results of this study suggest that the following areas require consistent focus and attention: Leadership Development; Accountability; Knowledge, Skills, and Abilities Development; System Coordination; Culture Enhancement; Behavior Optimization; and Risk Management Studies. Each element and its corresponding top-ranked and top-rated practices are discussed.INTRODUCTION Since the time of the Industrial Revolution, occupational health and safety (H&S) management has been a topic of practitioner thought and academic inquiry (1). In the U.S., decades of regulation and research have resulted in a surplus of prescriptive information (techniques, tools, approaches, standards, programs, practices, policies, etc.). With an abundance of such information, a simple H&S solution to address a problem in the U.S. mining industry may seem straightforward. Counter to this assertion, however, some evidence suggests that the abundance of information may create complexity and cause confusion in the minds of organizational leaders and H&S managers, ultimately discouraging the voluntary pursuit of a sound approach (2). In line with this perspective, in 2006 the U.S. National Mining Association (NMA) formed an independent commission to examine H&S management issues within the mining industry. The findings of the commission called for the mining industry to adopt a risk-based management paradigm. In the presentation of its findings, the commission stated that “…every mine should employ a sound risk-analysis process, should conduct a risk analysis, and should develop a management plan to address significant hazards identified by the analysis” (3). Grounded in the well-known plan-do-check-act cycle, the recommended risk management system allows for mines to ground strategic management choices in their mine-specific hazards and risk profiles"

Jan 1, 2015

By R. L. Neman

Southern Oklahoma (including the Arbuckle Mountains) has outcrops of rocks representing Precambrian, Paleozoic, and Cretaceous ages. Thus, rocks of every geologic age in the Paleozoic and Mesozoic Eras, except the Jurassic and Triassic Periods, are present in south-central Oklahoma. With rocks of such an enormous age range present in a relatively small geographic area, it is little wonder that a wide variety of economic rock and mineral resources are locally present. This report will describe the occurrence, mining, processing, and end-uses (dictated by chemical and physical properties) of the Precambrian Troy Granite, the Cambrian Royer Dolomite and Fort Sill Limestone, Ordovician silica sands of the Simpson Group, Ordovician limestones of the Viola Springs and Welling Formations, and Ordovician Sylvan Shale. In general, the more the end-use depends upon chemical composition and purity, the greater the price that can be demanded for such-minerals. The not-so-successful attempts to mine zinc, manganese, copper, and iron from the Arbuckle Mountains also will be discussed briefly, and I will provide a sermonette on analytical chemistry and its usefulness to corporate CEOs. I may be one of the few persons at this Forum on the Geology of Industrial Minerals who is not a professional geologist. I am an analytical chemist specializing in geochemistry. In particular, I investigate trace elements in rocks and their consequences in industrial processes. As such, I have consulted to the mining industry (and their clients) for two decades, always with the intent of improving service and product quality.

Jan 1, 1999

By Steve Kral

"Repairing and replacing the nation’s aging and crumbling infrastructure has become a major issue with the American public. It is no secret that the upkeep of roads, tunnels, bridges, and water and waste water facilities has been neglected for decades. Cities, states and towns across the United States are now grappling with these issues, ones that will take decades and billions of dollars to fix.Because of this infrastructure issue, the North American tunneling industry is flourishing. Cities across the country are looking to go underground to alleviate traffic issues, transporting water and waste water to more people in more efficient ways.In October, the seventh annual Cutting Edge conference was held in Atlanta, GA. Put on by the Underground Construction Association of SME and Britain’s Tunnelling Journal, about 175 tunneling and underground construction professionals from around the world attended. Attendees included owners, designers and contractors. An accompanying exhibit included 28 companies.The theme of the two-day conference was Advances in Tunneling Technology. Speakers examined the latest advances in tunneling technology, its methodology and how these advances can be harnessed to assist upcoming major tunneling projects. The conference featured a tailored, high-end, single-track program of subject-specific presentations that focused on innovation and practical experience. Two in-depth panel discussions at the end of each day were also included.Patricia Mulroy was a keynote speaker on Monday. She is senior fellow for climate adaptation and environmental policy at The Brookings Institution. Like many others, Mulroy believes the U.S. infrastructure in in a state of disrepair. But, she said, no one wants to talk about it. “We need to have a conversation about infrastructure. We cannot be afraid to talk about building it and the cost.” For this to happen, though, the nation needs leadership."

Dec 1, 2018

In spite of the tremendous amount of research conducted in the last few decades. no single blasting theory has been developed and accepted that adequately explains the mechanisms of rock breakage in all blasting conditions and material types. Given specific test environments, conditions and assumptions, individual researchers have contributed valuable information and insight as inputs into blasting theories, although a simple "plug-in" type formula for predicting optimum fragmentation, muck pile geometry and casting distance, is still largely unresolved. There is as yet, no consistent and widely applicable theory of blasting, but only a number of limited and disconnected theories; many of which are empirical in nature and based on ideal blasting conditions. Blasting theories have been formulated and based on pure speculation, years of blasting experience on a trial-and-error approach, laboratory testing, field investigation, and mathematical and physical models adapted from other disciplines of science.

Jan 1, 1988

By L. Runqing, H. Yuehua, S. Lei, S. Wei

"Tin ore from the southeast of Yunnan in China is a complex polymetallic low-grade ore. Because of the highly disseminated extent ore, cassiterite flotation was applied in industrial production instead of the low efficient gravitational separation. Benzohydroxamic acid (BHA) was widely used as a collector in cassiterite flotation, but the consumption of BHA was large. In this study, the influence of octanol in cassiterite flotation from the southeast of Yunnan using BHA as the collector was investigated. The results indicated that single octanol showed almost no flotation capability to cassiterite without BHA. However a small amount addition of octanol as the auxiliary collector can decrease the consumption of BHA significantly, while did not reduced the recovery of cassiterite obviously. Infrared spectra analysis indicated that the single octanol adsorbed on the surface of cassiterite was unsteady adsorption, and a new entity assembled of BHA and octanol in a well manner was able to adsorb on the surface of cassiterite steadily. The probable self-assembly structure model of BHA and octanol existing on the surface of cassiterite was analyzed. INTRODUCTION Cassiterite is the prime and economic mineral from which tin metal is extracted economically (Qin et al., 2011). The estimated tin metal resources in the world is about 4.9 million tonnes, about 30.5% of which is distributed in China (Mineral commodity summaries, 2013). Cassiterite has many characteristics such as including heavy, hard, and extremely brittle in nature. Hence cassiterite is preferentially concentrated by gravity separators. However, the influence of particle size on gravity concentration is obviously. The separation efficiency is very high for coarse particles while it drops down considerably for fine sizes. (Turner and Hallewell, 1993). Application of flotation and development of selective surfactants have made it possible to recover fine and ultrafine cassiterite from the gravity tailings. A substantial amount of research work on cassiterite flotation has been reported in the past years. The outcome of such research has helped to develop various collector reagents such as cupferron (Vivian, 1927), sodium dodecyl sulfate (Edwards and Ewers, 1951), sodium oleate (Collins et al., 1968), salicyaldehyde (Marabini, 1978), alkyl and aryl arsonic acids (Senior and Poling, 1986), alkyl and aryl phosphonic acids (Gruner and Bilsing, 1992), alkyl sulfosuccinamates (Khangaonkar and Kamarudin, 1994), and alkyl hydroxamates (Sreenivas and Padmanabhan, 2002)."

Jan 1, 2016

By R. Bhaskar

The advantages of recirculation of air in underground mines have been well recognized, and several papers have been written on the subject. Issues of concern to the various segments of the mining industry relate to the health and safety of workers, specifically, methane and respirable dust build-up in the air, high humidity and temperature at the work face. This paper presents a survey of various studies pertaining to recirculation as a prelude to the experimental and quantitative studies performed by the authors. Experiments were performed at a trona mine on the transportation and deposition of dust along the return airways, for three different velocities. Modeling studies were performed using dust deposition models. The model predicted data were compared with experimental data in order to lay the foundation for the development of advanced predictor models for recirculation in trona mines. Two models for dust deposition were analyzed. The model predicted data are in divergence from the experimental data, indicating the need to develop better models.

Jan 1, 1992

By H. J. Sandri

In the spring of 1991, Western Aggregates, Inc. began operating the newest expanded shale lightweight aggregate operation in North America. The operation is located in Jefferson County, Colorado, just south of Boulder, at the sight of the former Ideal Basic Industries ("Idealite") lightweight aggregate plant, which was decommissioned in 1975. The "new" facility has been built to principally serve the Denver and Front Range markets, as well as ship products into other locations in Colorado, Wyoming, New Mexico, Kansas and Nebraska. Western Aggregates is a wholly-owned subsidiary of Inco U.S., a subsidiary of Inco Limited of Toronto, Canada. Inco Limited is the free world's largest producer of nickel and is a leading producer of copper, cobalt, gold, silver, and platinum group metals, high nickel and super alloys, and specialized engineered products. Inco is constantly seeking new mining related investments that leverage off its mining and processing skills and that meet corporate fmancial objectives. Construction materials are an area presently being pursued by Inco. The basic 'building blocks' of society, from a construction perspective, are sand and gravel, stone, and aggregates. To the vast majority of people these are natural products that are mined, quarried or dredged, and other than washing, screening and crushing, are generally used in their primary form. While these materials vary from quartzite river rock, to calcified limestone, to hard basalt, they are generally classified as "heavy" aggregates. There are, however, other types of aggregates that do not fall under the "heavy" classification, but are used in general construction activities just the same.

Jan 1, 1992

By G. Harper

The Windy Craggy polymetallic massive sulphide deposit is located in the extreme northwest corner of British Columbia 40 miles west of the Haines Highway, 90 miles northwest of the port of Haines Alaska. The physical setting is mountainous country but with few peaks rising above 2,000 metres elevation, in contrast to the spectacular mountainous terrain to the north and south in Kluane and Glacier Bay Parks respectively. Valleys are classically U-shaped with incised V-shaped bottoms. The upper portions are still occupied by glaciers, which in the Windy Craggy area are documented as retreating at a rapid rate -in the case of the Tats Glacier of the order of 1% of its mass per year. The outcrops around Windy Craggy show a north-easterly dipping sequence of Mesozoic limey sediments and volcanics being the western limb of a north northwesterly trending syncline. Northeasterly cross folding provides a few complications. The flanks of the syncline have been buttressed by intrusive bodies of granitic affinity.

Jan 1, 1991