Search Documents

By T. J. Driscoll

The effect of coatings on the incendive properties of aluminum alloy 6061-T651 in air-6.4%CH4 was studied for collisions between rusted steel and both uncoated and coated projectiles with incident energies as high as 300 J (220 ft-lb) and velocities as high as 200 m/s (660 fps). These conditions were intended to simulate the rough handling of equipment in coal mines. The ignition probability using uncoated alloy projectiles increased with increasing relative humidity and appeared to be influenced by atmospheric ozone content. The incendive properties of both the uncoated and coated alloy depended on the type of rust used, but the dependence of the coated alloy was very different from that of the uncoated alloy. A number of coatings developed in the last 25 years were found to offer protection from ignition and to remain largely intact for occasional collisions or collisions randomly distributed over the coating surface, but probably not for repetitive collisions at any given point on the coating. These protective coatings utilize a hard anodized aluminum alloy surface coated with one or more layers followed by heat treatment of the coating. Coatings containing Teflon and MoS2 and thicker than 50 µm (2 mils) appear to be most effective.

Jan 1, 1987

By S. K. Kawatra, A. K. Bakshi

Mineral suspensions in water show Newtonian flow properties at low percent solids. However, this changes to a non-Newtonian regime as the pet-cent solids increases. For Newtonian fluids, viscosity is independent of shear rate, hut, for non-Newtonian fluids, viscosity varies with shear rate. Therefore, if the slurry is non-Newtonian, attempting to measure the viscosity at a shear rate different from the shear rate experienced by the fluid within the process is futile. This is especially true for a hydrocyclone, where the rate of shear is different at different points within the hydrocyclone. In this case, it is very important to determine the flow type of the suspension before attempting to establish any correlation between the viscosity and the process efficiency. A new technique to distinguish such changes inflow type was developed. This involves two viscometers: a coaxial cylinder-type viscometer that measures apparent viscosity at low shear rates and a vibrating sphere-type viscometer that measures the apparent viscosity at high shear rates. For each of these instruments, special precautions were taken to allow, for the measurement of the viscosity of rapidly settling mineral suspensions. Because the vibrating sphere viscometer is operated at a much higher shear rate than the rotating viscometer, the two instruments together could determine the shear-rate dependency of the viscosity. Ground silica (80% passing 65 µm) in water was used to prepare slurries at concentrations ranging from 10% to 70% (by weight) solids. The viscosity of each slurry sample was measured simultaneously by both viscometers, and the results were compared. With this technique, it was found that all of the silica-slurry samples tested were in the Newtonian flow regime for up to 70% (by weight) solids. Methocel and Cellosize polymer solutions showed clear non-Newtonian behavior using this technique. This confirmed that non-Newtonian behavior of the silica slurries, if present, would have been detected by this arrangement.

Jan 1, 1997

By D. W. Fuerstenau, G. S. Sudhir, P. C. Kapur

Quartz-limestone feed mixtures were ground in a laboratory-size, choke-fed, high- pressure roll mill. As compared to individually ground minerals, the harder component (quartz) in the product mixture is coarser, and the softer component (limestone) is finer. An energy split index is introduced for quantifying the disproportionate split of the mill energy between the feed constituents. This index is incorporated into a grinding kinetic model for simulation of the product size distributions of the mineral components as a function of energy input to the mill. The self-similar character of the size distributions is analyzed and an energy-size reduction relationship for the roll mill is highlighted.

Jan 1, 1992

By B. K. Mishra, R. K. Rajamani, A. D. Joshi

The liners are the most important part in the SAG mill operation. Hence, the liners and their design parameters are primarily studied to see its effect on SAG mill operations. Effective liner designs are directed to reduce downtimes, which is needed for the replacement of worn liners. There exists constant chance of improvement in the capacity of mill by studying the effect of liner design on the charge motion inside the mill. This need is satisfied by three-dimensional discrete element code "Millsoft", which uses Discrete Element Method (DEM) to analyze the motion of charge. This simulation of SAG mill keeps track of all the moving bodies like ball and rock and observes its interaction with liners and lifters. The recent work done on this software helps generating mill to more reality by putting conical wall at feed and discharge end, over the earlier flat walls. Millsoft is an effective tool to watch the change in the motion of the charge due to different types of lifter bars and different design parameters. It was concluded that by simply increasing chord length between the lifters and increasing the face angle of the lifters, capacity of the mill could be increased. On the other hand, this software can also be used to get power draft at the respective mill design.

Jan 1, 2002

By R. J. Reuss

Mina Maria is a high-grade, underground copper mine located in the Cananea district of Sonora, Mexico. The ore body is a massive sulfide breccia located in mountainous terrain. A major highway and an electric transmission line pass directly over the near-surface ore body. The mine is operated by Minera Maria SA de CV, a joint venture company that is 51 % owned by Empresas Frisco SA de CV and 49% by Cominco Resources International Ltd. Empresas Frisco is the operating partner. Production began in October 1990. The mining method used is undercut and fill. A continuous miner and a single-boom, hydraulic jumbo mine the ore. Backfill is a weakly cemented sand-gravel mixture that is pneumatically placed. The ore is treated by conventional crushing, milling and flotation. The Maria deposit is located about 40 km (25 miles) south of the Sonora-Arizona border and 11km (7 miles) northwest the city of Cananea and the Cananea Mine. The mine portal, at an elevation of 1780m (5840 ft), is on the east side of an important drainage divide. The mill site is situated about 800 m (2625 ft) northwest of the mine on the northwest side of the drainage divide where the drainage is more favorable. Its elevation is 1860 m (6100 ft) (Fig. 1).

Jan 1, 1992

By John A. Herbst, William T. Pate, Ruben Tello Flores, Humberto Arreola Zarate

Plantwide control is the networking and coordination of individual control systems throughout the plant to enhance plant performance. The high level decision making involved in this coordination is used to achieve overall plant optimization. Decisions must be based on knowledge and information moving between control systems in both downstream and upstream directions and on management information systems containing financial data on the impact of coordinating actions. For example, certain quantitative descriptors of upstream operations are passed to the downstream control systems to prepare those operations for the feed material they will receive. Likewise, other quantitative descriptors of downstream operations are passed to upstream control systems to modify their output. In this case, setpoints are determined throughout the plant which maximize profitability, given current ore conditions and plant operating constraints. Due to the wide area coverage of this coordinator, it is forced to draw on several diverse information and knowledge bases. Such a coordinator, then, must rely on a combination of heuristic logic, model-based control and neural networks to unify the knowledge bases as well as to take advantage of their strengths and to compensate for deficiencies. A description is given of control systems for primary and secondary grinding and flotation at a large copper concentrator and how they are being integrated to achieve plantwide control. Financial implications are discussed.

Jan 1, 1995

By K. Komnitsas

This paper presents the main environmental assessment techniques and indicators that can be used a) for the establishment of a sustainable development framework and b) for the evaluation of the environmental performance within the mining sector. Reference is made to techniques as environmental risk and impact assessment, life cycle assessment, cost benefit analysis and best practical environmental option assessment that can be used as tools to assess environmental impacts of processes, activities and products in the mining sector. In addition, the issue of environmental indicators, covering operational, management and environmental areas, that provide valuable information regarding both the environmental performance of a mining company and its efforts to influence this performance towards sustainability is discussed.

Jan 1, 2003

By J. M. Kruger, P. Berendsen, A. Martinez

High-resolution ground-penetrating radar (GPR) was used to image the near-surface extent of two exposed Late Cretaceous kimberlites intruded into lower Permian limestone and dolomite host rocks in northeast Kansas. Six parallel GPR profiles identify the margin of the Randolph 1 kimberlite by the up-bending and termination of limestone reflectors. Five radially intersecting GPR profiles identify the elliptical margin of the Randolph 2 kimberlite by the termination of dolomite reflectors near or below the kimberlite's mushroom shaped cap. These results suggest GPR may augment magnetic methods for the delineation of kimberlites or other forceful intrusions in a layered host rock where thick, conductive soil or shale is not present at the surface.

Jan 1, 1998

By Alberto Sarmentero

Venezuela, once a world's top gold producer until 1886 Witwatersrand discovery, did let fall its role then because of a serious lack of infrastructure and population, and lately (since World war II times), because of discouraging mining and taxation laws, laying upon an oil prizes bonanza. Recent research leading to estimates of about 5.000 mt. of gold, mainly related to the greenstone belts of the Guiana Precambrian shield outcropping in Venezuela, are opening the scope for both Government and international investing and mining companies, for gold exploration and development projects in the country. This paper overviews Venezuelan Gold mining industry, as seen from the point of view of a participating mining company.

Jan 1, 1989

By D. T. Kinard, A. A. Schweizer

An operational 9 meter (30-foot) high gold heap leach pile was investigated by excavating test pits up to 6 meters (20 feet) deep, obtaining bulk and relatively undisturbed thin wall drive samples, and observing the ore distribution patterns exposed in the test pit walls. The clayey ore is crushed, agglomerated with lime and cement, and deposited on the leach pads using a radial stacker. Laboratory tests performed included moisture-density, gradation, compaction, Atterberg limits, permeability (constant and falling head), and triaxial strength tests. Discussion is presented on the effects of agglomeration on the permeability and strength characteristics of the in-place ore. Also discussed is the effect of deposition of the ore using the radial stacker.

Jan 1, 1987

By L. Adler

In spite of distractions from glam-our areas (ground control, computers, etc.), excavating and bulk handling in mining remains paramount but is now undergoing dramatic advances. The massive intervention of mining and civil engineers as "engineer-users" into the tight, exclusive, and specialized bond between the equipment operator ("operator-users") and the manufacturer (mechanical engineers "and sales "reps") has now occurred. Three developments have accelerated this: 1) larger, more costly, complex, specialized, and innovative equipment; 2) a more profound understanding of the equipment, operations, and working conditions (encumbered space); and 3) a concurrent thrust into "high-tech," (automatic and remote controls, sensors, automation, artificial intelligence, and even robotics) and human factors (workload intensity, work-station design). This has produced a well-defined professional discipline, including construction and even military engineering. The mine plant, and to a lesser extent, the mine face, is now being monitored. Equipment conferences, journals, and centers at universities and agencies have multi-plied. The discipline's impact on future mining now becomes more apparent.

Jan 1, 1988

By Steven W. Hunt, Phillip U. Santacroce, Roger C. Ilsley

Consolidation grouting from the surface prior to mining a shaft is commonly performed to reduce groundwater inflows to a manageable rate. This paper describes the inflow reductions obtained within dolomite and limestone formations at several shafts and chambers due to grouting programs for the Milwaukee Water Pollution Abatement Program. The resulting inflow reduction factors are compared to results reported in the literature for other projects. Post-grouting pump tests are also evaluated as an aid in grouting assessment. Important considerations for estimating shaft inflows from pump test results are discussed. These considerations include loss of grouted mass during mining and influence of blasting and rock features on grouting effectiveness. This information should be helpful to design engineers and contractors who need to estimate inflows after pre-excavation consolidation grouting has been performed.

Jan 1, 1993

By Robert J. Timko, R. Lincoln Derick

This report presents a Bureau of Mines evaluation which examined the extent of gas leakage from sealed areas in underground coal mines and measured the effectiveness of commonly used structures for controlling the quantity of gas exchange from these areas. Evaluations were performed on five abandoned areas in two operating underground mines within the same coal seam. Methane and oxygen levels inby the seals were monitored to determine if the gas leakage was unidirectional or bidirectional. Results from this and prior work dealing with minimizing gas leakage were then applied to a newly abandoned area. Also discussed are bulkhead site preparation, construction plans, techniques for monitoring the status of the atmosphere within the sealed volume, and a modified European method for controlling gas migration from the sealed volume to the active mine.

Jan 1, 1991

By R. S. Conti, L. L. Chasko

To deal with an unexpected event such as fire, prevention and preparedness are important elements in an underground mine's strategic plan. The purpose is to prevent afire before it initiates and to be prepared to deal with it when it does occur. This paper highlights a technology that may be used by the mining workforce to minimize such occurrences. It discusses thermal imaging cameras and their many applications to detect equipment failures or hot spots before they develop into afire. It also evaluates the feasibility of using thermal imaging cameras for emergency responders to assist them during exploration, rescue and fire fighting efforts. These thermal imaging systems allow rescue personnel to see in darkness and through dense smoke, thus making it easier to locate heated areas and missing or trapped personnel.

Jan 1, 2003

By J. W. Stevenson

The need for a separate ventilation department within the management team was recognized by the management of U. S. Pipe and Foundry before the company was purchased by Jim Walter Corporation in January, 1970. Because the coal beds of the deep underground coal properties owned by Jim Walter Resources lay 1300 to 2200 feet below the surface, efficient mine ventilation practices are essential through shaft openings varying from 16 to 22 feet in diameter. The extremely high methane gas quantity indicated to be in the coal bed because of the depth of cover and documented by various U. S. Bureau of Mines tests and demonstrated by early mining proved the need to implement this early management decision. At U. S. Pipe and Foundry mine ventilation was a function of the Mining Engineering Department with ventilation personnel assigned to the mine receiving their day to day work assignments from the mine manager or mine foreman. At Jim Walter Resources, the General Manager - Ventilation reports to the Senior Vice President, Mining Engineering, who reports directly to the President, Mining Division, Figure 1 (Company Organization Chart). Position descriptions are static; however positions are dynamic and consequently the degree of emphasis of specific duties and responsibilities change depending not only upon the aptitude of the individual performing the job but also upon his ability to meet the needs of his supervisors; and ultimately upon his ability to react to the economic forces directing our society. The following describes the duties and responsibilities of the General Manager - Ventilation, Figure 2.

Jan 1, 1980

By Charles H. Grant

Blast design methods generally deal with end points or limits of design such as spacing, burden, stemming depth, etc. Even cratering design deals with limits defined as a function of energy decay to a limit. Although this crater method provides a better method than trial and error judgment it does not take into consideration the distribution of energy throughout the material to be blasted. This paper deals with a method of examining this distribution with the aid of a computer and how changes in blast design affect this distribution. First I would like to explain the equation used to develop the energy summations throughout the blast. As shown in Figure I a series of drill holes are drilled to various depths starting by placing the explosive charge on the surface and then at various depths until a sufficient depth of hole is reached to exceed the ability of the explosive energy effect to reach the surface of the ground. All volumes of explosive are the same, all holes contain the same explosive and the drill hole diameter is the same.

Jan 1, 1980

By David E. Thompson, Daniel J. Dobbels

INTRODUCTION The planning process for projects requiring construction of tunnels in urban environments can be highly complex and involves interaction with professionals of many disciplines. Typically the initial step in the planning process is to establish basic design criteria for the tunnel or tunnel system consistent with its intended purpose. Such criteria might include acceptable tunnel geometry, minimum and maximum slope or other associated criteria. Ideally, once the basic criteria have been established, the next step in the process might include establishing technically feasible horizontal and vertical alignment and shaft siting alternatives and developing "ball park" construction and operational cost estimates for the alternatives. Comparisons can then be made regarding the relative technical and economic merits of the alternatives and the most favorable alignment(s) are selected for further study or preliminary design. Typically the last and perhaps the most important task that is conducted during the planning stage includes identifying issues and potential problems to be addressed during the design and construction stages of the project. Many issues warrant consideration during the planning phase of a tunneling project. For the purposes of this paper, these issues can be divided into two broad categories: technical and non-technical. Important technical issues include, among others, general design criteria, geotechnical and geoenvironmental issues, and constructibility issues. Important non-technical issues include, among others, right-of-way and easement related considerations, project scheduling constraints, both short and long term environmental impacts and overall cost/benefit aspects of the project. With respect to influence on the planning process, these two groups of issues often cannot be separated completely. For urban tunneling projects, however, it is most often the case that the non-technical

Jan 1, 1991

By M. B. Díaz Aguado

Traditionally, the practical evaluation of a mining project for a potential investment has been made considering mainly technical aspects. But the concept of sustainable development has introduced significant changes in the factors analyzed to make the final decision. This paper proposes an empirical evaluation of a project considering not only technical, economic and financial parameters, but also associated risks and other intangible aspects, such as political considerations, stability in the legal frame, social factors and environmental issues. The proposed methodology is practical and easy to apply for project management. Among its main advantages, the following could be quoted: using this evaluation two different projects or locations of a same project can be compared, future behaviors could be predicted, the index incorporates a new approach to specific mining projects and this perspective could also be applied to other projects with environmental and social impact, such as civil works or industrial projects.

Jan 1, 2007

By Roger Mourich

As the Powder River Basin coal industry has grown, many changes have occurred in the coal market, the economy and the Basin's methods of dealing with competition in the coal mining business. This article notes the mines that have changed to draglines as the major overburden-stripping tool. The Powder River Basin is defined as those mines within a 97 km (60 mile) radius of Gillette, WY. Mines to the north and south of this area - Decker, Spring Creek, Glenrock - have used draglines more extensively. The reasons for the conversions to draglines at each mine, and the specific timing of these changes, were different. However, the driving factor was economics. As coal production increases, strip ratios increase and coal sales prices decrease, mines must find ways to deal with rising costs and falling revenues. The primary method used has been conversion of overburden stripping to dragline operations. Stripping ratio equals the bank cubic yards of overburden removed for every ton of coal mined.

Jan 1, 1994

By Lars Lövgren, Jörgen Jönsson

Heavy metals may be retained within deposits of sulfide minerals under oxidation and in the nearest recipients of drainage water by sorption to secondary iron precipitates. The extent of sorption is strongly influenced by solution pH and presence of complexing ligands, such as sulfate and natural organic acids. Desorption of metals and organidinorganic anions to recent secondary Fe precipitates, collected at the Kristineberg mine, Sweden, has been investigated under different geochemical conditions. Elemental composition and structural characterization (X-ray powder diffraction) indicate presence of schwertmannite. While metals such as Ni and Pb were fractionally desorbed from the precipitates under acidic conditions, oxyanions, e.g. arsenatdarsenite and sulfate were desorbed preferably under alkaline conditions. In a separate study the adsorption of NOM onto synthetic goethite was investigated. NOM adsorption showed a strong pH dependence, 95% was adsorbed at pH 3 and 40 % was adsorbed at pH 9. Addition of 2 mM of sulfate desorbed about 10 % of the adsorbed NOM.

Jan 1, 2000