Search Documents

By Schebek, J. Warsen

"Data and information from sustainable development (SD) reports can be seen as a promising and easily accessible source for an Life Cycle Assessment (LCA), i.e. for generic Life Cycle Inventory (LCI) data in particular. The reliability and comparability of LCA results crucially depends on the quality of LCI data, that is defined by specific normative requirements. In parallel the GRI (Global Reporting Initiative) provides a set of guidance documents for enhancing the quality, rigor, and utility of SD reporting with specific reporting principles that address similar issues on a company level comparable to LCI data quality requirements on the process level. In order to assess the general suitability of the fundamental reporting principles for LCI data quality purposes selected reports from mining and minerals (M&M) sector are assessed within a detailed analysis."

Jan 1, 2005

By Jon C. Volkwein

The U. S. Bureau of Mines investigated a method of using inert gas to prevent the formation of explosive gas mixtures in auger highwall mining of coal. A combination of gasoline and diesel engine exhaust gases was introduced into the auger drill hole using a short section of pipe located at the collar. Gas samples were taken and analyzed on site with infrared detectors for oxygen, carbon dioxide, methane, and carbon monoxide. Evacuated bottle samples were also taken and analyzed by gas chromatography at the Pittsburgh Research Center. These gas results were analyzed for explosibility. Personal exposure to carbon monoxide was also monitored. The highest methane level observed was 9.55 pct. The Inert gas levels, (carbon dioxide and nitrogen) were sufficiently high to prevent any ignition of the methane. Results showed that for all conditions during mining, gas concentrations were non-explosive. The maximum personal time weighted average sample for carbon monoxide was 20 ppm. This system provides a safe, inexpensive, simple method for preventing explosions during auger mining. INTRODUCTION The auger highwall mining method is an effective method to recover coal from a reserve when removal of the overburden by surface mining equipment becomes uneconomical. In this method of mining, a horizontal auger enters the coal seam from the surface mine bench under the highwall and the coal is drilled in a series of parallel holes. Historically, coal mined from the surface is relatively shallow, and over time, methane associated with the coal has dissipated through the surface. In most circumstances, little methane has been found associated with auger mining. However, mining technology has enabled surface mining of deeper reserves of coal. Furthermore, environmental constraints have forced the highwall extraction method to be used to remove coal under wetlands, further increasing the chances of encountering methane. Recently incidents of methane explosions at a few auger mining operations have resulted in injuries and increased testing for methane at the collars of auger holes. The fuel source of the reported explosions was not necessarily limited to methane, but may also have involved coal dust. The Mine Safety and Health Administration (MSHA) met with the Bureau to discuss what technology might be available to enable the safe resumption of mining. The discussion included the difficulty of ventilating through the solid shafts of the augers, that steel bits probably created the ignition source, and that perhaps inerting the holes with low oxygen and high carbon dioxide concentrations from the machine's diesel exhaust was a potential solution. Considering the ventilation aspects of the problem, it was not clear If ventilation could be reliably established. If some degree of ventilation to the front of the mining head is achieved, it may combine with methane to bring the hole atmosphere from a rich, nonexplosive mixture to an explosive mixture. Furthermore, it may not prevent a dust explosion in such a mining configuration. Lack of access through the shafts of auger type mining machines further limits the ability to add water or air to cool bits to prevent an ignition source from developing. Either of these approaches would also be expensive. The process of mining coal In an inert atmosphere has been considered in the past, but to our knowledge, never implemented (Department of Interior, 1970). Clearly, implementation in underground mining would be more complicated. On a mine bench open to the atmosphere, however, adding inert gas to the mining head could provide a quick, feasible method to prevent explosions at auger highwall mining operations. Also the problem of how to move the inert gas to the cutting head of the machine had to be considered. Preventing explosions on auger mining machines using inert gas requires three primary considerations: first is the source of inert gas; second, placing the inert gas at the cutter head; and third, monitoring the hole atmosphere. Any gas source having an effective inert gas concentration of 34 volume pct or greater will prevent methane from Igniting (Zabetakis, 1965). Sources of inert gas considered for this application included liquid nitrogen, modified shipboard inert gas generators (for hydrocarbon shipping and transfer), jet turbine engine (Paczkowski, et. al., 1982), the auger's diesel engine and a gasoline engine. Operation cost, purchase cost and availability limited our testing to the diesel and gasoline engines. This work tested each engine, separately and combined. To ensure effectiveness, both company and enforcement personnel need to know how to monitor the condition of the inerted hole. Measurements at depth inside the hole are possible by remote sampling through rigid tubing, but this method is Impractical for routine monitoring. Continuous monitoring of the exhaust gas stream is an alternative. The U. S. Bureau of Mines evaluated an inert gas system at an auger mining operation at a surface mine near Owensboro, KY. Coal was mined from the Number 9 Coalbed in Henderson Co. KY. Tests were conducted in January and March of 1992.

Jan 1, 1993

By C. L. Schaidle

Computers and communications technology have revolutionized many industries. In earthmoving, this revolution has just begun. The major changes are still to come, but they are just around the corner. This paper presents a vision of this up-coming revolution in our industry. This vision is comprehensive. It includes basic communication, machine monitoring and diagnostics, job and business management, planning and operations, and machine control. For our industry to realize maximum benefits from the information age, we must have a vision of the future that is shared by technologists, machinery producers, and miners.

Jan 1, 1994

By P. C. O. Chukabarah

Atkinson's resistance square law is the cornerstone equation for traditional expression of energy losses in mine ventilation engineering. But the nomenclature for the various forms of energy losses are often confused for one another, misapplied or misinterpreted. These forms of energy were re-examined from thermodynamic and fluid-dynamic perspectives. Resultant expressions showed that both incompressible and compressible flow regimes in underground mines can easily be accommodated. Given the well-known three major energy forms, which are equivalent to one another but numerically unequal, corresponding equations to Atkinson's (pressure loss) for headloss and workloss were derived. The thermodynamic weight relational resistance ([w] s2/m5) associated with energy per unit weight (headloss) was dimensionalized for the first time. Also, normalized Atkinson-like equations for headlosses and worklosses were derived to ease direct computations in mine ventilation practice.

Jan 1, 1995

By Rudy Rogers

When Gas hydrate formation rates have two steps: a nucleation induction step and an agglomeration step. Hydrate induction in distilled water is extremely slow because of lack of nucleating particles. Our laboratory found that synthetic anionic surfactants greatly improve both hydrate induction and agglomeration because the surfactant?s hydrophilic head absorbs water molecules and the hydrophobic tail absorbs hydrocarbon gas molecules, creating necessary nucleation sites. Vast hydrate deposits inhabit seafloors. What is the seafloor hydrate nucleating mechanism? We find that nano-particles of smectite clays (bentonite and nontronite) are hydrate-nucleating sites in sea-water-saturated, packed porous media, especially when trace quantities of anionic biosurfactants adsorb on the clay particles. Microbes and their bioproducts proliferate around seafloor gas hydrate accumulations. The seafloor microbe-mineral-hydrate synergy is explored in this paper. Keywords: gas hydrates, biosurfactants, crystal nucleation, smectites

Jan 1, 2008

By T. A. McAfoose

As one of the major suppliers of the chestnut Ridge energy center, Rochester and Pittsburgh Coal Company continues the search for more efficient haulage systems. This search is one that is essential in providing coal to the Keystone and Homer City power plants at the most economical cost. These two electrical generating plants located in west central Pennsylvania are part of the energy center which consists of four generating stations. Prior to the time the two stations were put on line, August, 1967 for Keystone and August, 1969 for Homer City, our company made the decision to rely on belt conveyors from the section to the surface to provide for continuous main line haulage. The proximity of these generating stations to proven reserves allow for minimal truck haulage and minemouth setups. With the addition of seven new mines, in the past ten years, revisions have been made on the original setup to interconnect the haulage of several mines to deliver the product by belt to the power plants.

Jan 1, 1979

By M. Sengupta, N. I. Johansen, A. K. Sinha

In Arctic surface mines, frozen ground adds to the complexity of slope stability analysis. The seasonal temperature change may thaw permafrost, and this thawed ground is often unstable. A computer program, GEODYNE, was used to simulate the movement of the thaw front in bare and insulated permafrost slopes. The simulation shows that the insulation can be used on mine slopes to prevent thawing.

Jan 1, 1990

By L. W. Laage

MFIRE is a mine ventilation and fire interaction computer simulation program. It allows transient state ventilation simulation and features mass based flow rates, natural ventilation, air recirculation, fan curve fitting, airflow reversal and product of combustion tracking. MFIRE was designed to accommodate the needs of the mining industry for routine ventilation calculations and mine emergency planning. This paper describes recent work by the Bureau and MTU to improve MFIRE by incorporating humidity in the mass flow and heat exchange calculations, a data file preparation program and variable reference density in the network calculations. Recent bug fixes are also discussed.

Jan 1, 1993

By G. E. Bandelis

In this paper, solid bed erosion processes and the mechanisms involved when a two-phase liquid-solid mixture flows over a bed of solids in a horizontal annulus are analyzed. There are few such studies available with some authors arguing that the flow rate for erosion is always less than the flow rate for the suspension of solid particles thus necessitating further study and analysis of such phenomena. Tests were run to determine the mechanism of erosion and the erosion velocities of the solid bed formed in a concentric annulus for three flu-ids, water, a low concentration water solution of Carboxyl-methyl-cellulose (CMC), which behaved as a Newtonian fluid and a higher concentration CMC water solution which behaved as a power law fluid. Glass spheres of 2 mm nominal diameter were used as solids. The flow rate at which erosion occurred together with the mechanism of bed erosion were determined visually, while the whole process was video recorded. Our tests indicated different erosion mechanisms and different erosion velocities for the three tested liquids, with the liquid viscosity playing a major role. The first mechanism, observed for water flow, gives erosion from the front of the bed while the second mechanism, observed for the flow of the two viscous fluids, gives erosion from the top of the bed. The role of each of the parameters to erosion is investigated, whether it is turbulent flow with the turbulent fluctuations being more capable to remove the solids from the formed bed or whether it is liquid viscosity, which results in the hydrodynamic shearing force. The results demonstrate that liquid viscosity plays a role in the erosion mechanism and yields different erosion velocities of the solid bed hence, it should be taken into account when modeling flow pattern transitions for solid-liquid flows. Prior studies have not identified this and it could be the reason of the disagreement between theoretical models and experimental and field data.

Jan 1, 2006

By Hongjie Yu, Mike Mooney

Transitions between geological/geotechnical soil units have a critical impact on the operation and performance of a tunnel boring machine (TBM). Geostatistics-based probabilistic modeling is used to quantify the uncertainty in soil transition locations. This paper presents two unique soft-ground tunneling case studies where the results from the geostatistics-based probabilistic modeling are compared to the TBM data and as-encountered ground conditions derived from the actual TBM data. The assessment enhances the confidence in using geostatistics to improve ground awareness for efficient tunnel construction, minimizing different site condition (DSC) claims, and improving decision-making on tunnel projects.

Dec 1, 2022

By H. Soto, G. Barbery

The effect of particle size on the flotation of coarse particles is analyzed. It is concluded that turbulence and the presence of the froth layer are detrimental to the recovery of coarse particles during conventional flotation. A counter-current column cell is proposed to avoid these two factors. In this column, a net upwards flow of water is prevalent, such that no froth is allowed to form on the top. Also, the levitation of heavy bubble-particle aggregates is helped by the ascending water current. Preliminary work at laboratory level with kilogram-size samples indicated that under similar conditions recoveries in the column were much higher than in conventional cells. Flotation results obtained with coarsely sized phosphate and quartz samples are presented. One interesting feature of this type of column is very fast flotation kinetics. Thus, a short column (only 55-cm collection zone) yielded, full recovery of floatable values.

Jan 1, 1992

By E. Topuz, M. J. McPherson, J. Banik

This paper summarizes the analyses of ventilation layouts for mines that experience both spontaneous combustion. The major focus is placed on the longwall coal mine layouts used in several countries. Each of the different layouts is modeled in the form of a ventilation network. The gob of a longwall panel is the most critical location for the occurrence of spontaneous combustion. Airflow leakage paths inside the gob are simulated by using a simplified grid-like network. Computer simulations with this model indicates that the W-system of ventilation is most effective in minimizing air leakage into the gob. Homer, the U-system of ventilation, with pressure balancing behind the face support line, is also found promising for longwall panels. The magnitude of air leakage into the gob is observed to change with the advance or retreat of bee, thus requiring appropriate balancing of pressure to maintain the leakage at a minimum.

Jan 1, 1995

By Peter A. Gillett, Ian S. Clelland, J. G. S. Hynd

Today mine shaft and slope contracts include a greater amount of ancillary work such as level and pump stations, loading pockets, rotary and side dumps and connecting raises. This ancillary work requires the application of a number of construction methods often for short periods and often at short notice if the contractor is to maintain a profitable operation. In the next decade, the number of shafts that will be sunk by a boring method will outnumber those sunk by traditional methods. This will be particularly true of the deeper shafts where water problems are minimal. The increase of bored shaft work will not decrease the work completed by the shaft sinking contractor but it will change it. A greater emphasis will be placed on the speed of construction of station and other ancillary work. To meet this challenge the contractor requires full information on the ancillary work as well as the shaft work at an early date, preferably pre-bid. The two examples discussed in this paper illustrate the importance of early information. The two main factors of shaft ancillary work construction are sequence and ground support. This paper describes two examples completed recently by The Cementation Company of America Incorporated in Arizona. The first described is a Rotary Dump-Ore Pocket-Ore Pass complex and the second described is the excavation of the Main Station Level in a 2 Station-Loading Pocket-Ore Pass complex. CONSTRUCTION OF ROTARY DUMP, ORE POCKET AND PASS Introductory

Jan 1, 1976

By André Vervoort

The roof behaviour in room and pillar panels during the development of roadways and the subsequent pillar extraction was monitored underground and numerical simulations were conducted. For several underground sites, a satisfactory, correlation was found between underground measurements and three-dimensional numerical simulations using a boundary element code in the linear elastic domain. However, to simulate bed separation, and roof block collapses more complex models were required, of which examples are presented.

Jan 1, 1992

Mining has traditionally been seen as a relatively risky business. Exploration is expensive and the failure rate is high, while start-up costs commonly run to many hundreds of million dollars. To justify the risk and expense, the returns from successful projects must also be high. Accurate estimation of mineral resources and reserves is fundamental to the processes of optimising returns and managing risk in mining developments. Systematic development from initial exploration through a series of development stages enables expenditure and risk to be balanced. As a consequence, large scale modern mine are more akin to manufacturing businesses. This paper examines the life history of a mineral reserve estimate from the perspective of a large mining company against a background of modern estimation and reporting requirements. It will also touch on what constitutes, in the author's opinion, `best' practice in reserve estimation, and how this concept can be spread more widely. [Abstract to be re-written and reduced to 100 words]

Jan 1, 2003

By Donald E. Hulse

Selection of a block size for a computerized 3 dimensional ore body model is an exercise in compromises. Larger blocks decrease the use of computer resources and decrease the variance of the block estimates. Smaller blocks increase the resolution of the model and the selectivity which can be used in the planning, but increase the variance of estimates in the individual blocks. A common rule is that blocks can be as small as one fourth the average sample spacing, however this ignores the interrelationship between the block size, the sample spacing, and the variogram model. This paper will explore this relationship Kriging estimation variance will be used as a comparative measure of estimate quality. Graphical techniques will be used to show that there is a point where smaller block sizes cease to contribute to the resolution of the model. A method of evaluating the consequences of block size decisions will be examined.

Jan 1, 1992

By Mark J. Schultz, William J. Francart, Gary J. Wirth

Atmospheric Monitoring Systems (AMS) utilizing carbon monoxide sensors have demonstrated their superiority over thermal type fire sensors for early fire detection in underground coal mines. After proving their capability and dependability throughout the 1980's, systems are now evolving and applying new technologies to enhance their effectiveness and reliability. The use of AMS in coal mines which utilize diesel equipment presents unique obstacles. Exhaust gases from diesel equipment not only raise mine ambient CO readings, but also cause numerous nuisance alarms. Both of these conditions reduce the effectiveness of the AMS. New technologies, such as discriminating devices, smoke detectors, and time delays, as well as administrative controls, have been developed and are being utilized to help reduce nuisance alarms produced by the diesel exhaust. This paper will discuss these technologies and administrative controls which are being utilized in coal mines to enhance the effectiveness of the Atmospheric Monitoring Systems. Reference to specific products does not imply endorsement by the Mine Safety and Health Administration.

Jan 1, 1995

By D. K. Denton, D. F. Scott, T. J. Williams

Spokane Research Center personnel have been investigating the use of seismic tomography to monitor the behavior of a rock mass, de¬tect hazardous ground conditions and assess the mechanical integrity of a rock mass affected by mining. Seismic tomography can be a valuable tool for determining relative stress in deep, >1,220-m (>4,000¬ft), underground pillars. If high¬stress areas are detected, they can be destressed prior to development or they can be avoided High-stress ar¬eas can be monitored with succes¬sive seismic surveys to determine if stress decreases to a level where de¬velopment can be initiated safely. There are several benefits to using seismic tomography to identify high stress in deep underground pillars. The technique is reliable, cost¬effective, efficient and noninvasive. Also, investigators can monitor large rock masses, as well as moni¬tor pillars during the mining cycle. By identifying areas of high stress, engineers will be able to assure that miners are working in a safer envi¬ronment.

Jan 1, 2000

By M. J. Shulman

The exploration geologist is frequently confronted with the problem of allocating his resources, i.e., exploration effort, among various areas. Although geologic, financial, and logistic considerations influence the allocations, no objective criterion is usually given that determines the optimal allocation. Maximizing the expected gain in information, subject to the constraint of a limited exploration budget, is used as the objective criterion to allocate airborne reconnaissance effort. The information function, I(x), quantifies the expected gain in information, where x is the scale of exploration. To calculate the information function, the following probabilities are required: the probability that an area contains a deposit; the probability that an anomaly is produced by the target; and the probability that an anomaly is produced by a barren area (false signal). Alternatively, the barren areas can be replaced by other targets. To illustrate the allocation method, the optimal number of line kilometers, i.e., the optimal line spacing per area, is determined for an aeromagnetic survey for iron in Egypt.

Jan 1, 1987

By T. P. Lim, A. J. Vivyurka, N. K. Davé

Chemical and radioisotope stratification studies were carried out in an abandoned uranium tailings pile at Elliot Lake, Ontario, Canada. The tailings, with an average thickness of 7 m over an area of 16 hectares, were deposited approximately 20 years ago on a layer of black peaty material which overlays deposits of permeable glaciofluvial sands. Geohydro-chemical investigations of this tailings area have been ongoing since 1978. The radioisotope profile study was conducted on three adjacent sites. Solid core samples, collected with a split spoon sampler at various depths, were analyzed for various chemical and radioisotope constituents. The results indicated by 2 distinct zones of stratification; an upper zone, where the constituents were uniformly distributed, and a lower zone, near the peat-tailing interface, which showed increasing concentration with depth. Within the peat layer, the concentration decreased rapidly with no significant levels of contaminant penetration below the peat layers observed, though the samples were limited. The pH profile showed that the top 5 m of the tailings have been oxidized, the average soil pH in this zone was 3.4 compared to 5 .8 underneath it. The groundwater hydrology of the system was observed to be complex showing downward and lateral flow in the dry season and lateral and upward flow during the spring and periods of heavy rainfall. The results are discussed in terms of a model based on the combined segregation and settling process of the tailings fine fraction, and the geohydro-chemical interaction of the solid and liquid phases.

Jan 1, 1981