Search Documents

By Karl J. Ellefsen

A geophysical investigation can provide valuable geologic information needed to characterize sand-and- gravel deposits and can be an attractive complement to more common characterization methods such as drilling. Although such investigations have been conducted already, a comparison of the different geophysical methods used in these investigations apparently has never been done. For this reason, a study was initiated by the Mineral Resources Program of the U.S. Geological Survey to determine the advantages and the limitations of different geophysical methods when used to evaluate alluvial sand-and-gravel deposits. The study is focused on those geophysical methods that are commonly available, because these are most likely to be used by industry. Furthermore, the study is focused on surface geophysical methods. Heretofore, four different methods have been evaluated. Three of the four methods-time-domain electro-magnetic (TEM) soundings, frequency-domain electro-magnetic profiling, DC-resistivity soundings-are similar in that they all measure the electrical resistivity of the ground with depth. Ground-penetrating radar, however, maps changes in the dielectric permittivity and for the electrical resistivity with depth. For all, four methods, the objective is to relate the measured physical quantity to the stratigraphy of the alluvial sediments.

Jan 1, 1999

By Gopalan Ramadorai

This paper presents a review of halogen solvents used in the processing of precious metals. Reagents of widely varying chemical structures, such as chlorine gas, calcium and sodium hypochlorite, chlorine dioxide, iodine and bromine have been used for precious metal extraction. None of these chemicals are a replacement for cyanide: however, each of these chemicals present an opportunity for use in processing a specific type of ore. The ore and chemical must be matched to each other for success. Recovery of metal from the leach solutions also offers challenges.

Jan 1, 1994

By L. B. Rothfeld

Two new coal use technologies are on the verge of commercial acceptance by the utility industry: atmospheric fluidized bed combustion (AFBC) and gasification combined cycle (GCC). Generating plants under construction or in planning will replace older pulverized coal (PC) boilers or substitute for new PC boiler capacity. This paper reports recent developments in the commercialization of AFBC and GCC, emphasizing the potential impact on the coal mining industry. The influence of coal quality characteristics on fuel selection is explored by means of preliminary economic calculations for different coals and competing fuels.

Jan 1, 1987

By Pradip

Chelatang agents, because of their metal specificity, can function as effective mineral processing reagents. A brief review of the work carried out in this area is presented. Some of the salient features of mineral flotation and flocculation with chehting-type reagents, such as bulk us. surface chelation, the role of pH, mineral solubility, solution chemistry of reagents, and temperature, are illustrated with appropriate examples. The problems associated with the commercialization of chelating reagents for ore beneficiation and the research efforts required in this area are also discussed.

Jan 1, 1987

By Thomas E. Browne

The Electric Power Research Institute Energy Supply Program is developing coal supply forecasts. By coal supply forecasts I mean the future relationships between coal price and production levels. A representative supply curve is shown in Figure l. It will make the rest of my presentation clearer if at this point I give you some background about EPRI and the Energy Supply Program. EPRI is funded by the nation's electric utility industry to develop new technologies for the production and conservation of electricity. Most of the research is conducted by outside contractors. We participate in joint projects with the Department of Energy and other organizations. The Energy Supply Program is one of three "economic" programs. The other two are Energy Demand and Conservation, and Systems. The Systems Program's main function is to provide the means to integrate the output of the other two Programs. The primary function of the "economic" programs is to provide information pertaining to future energy prices, availability, requirements, etc. to the EPRI personnel planning R&D programs. A secondary role that is becoming more and more important is providing information of direct use to the electric utility industry. I should note that the results of all EPRI's contract work are available to the general public. A "Coal Supply Analysis System" is being developed for EPRI by Charles River Associates. To the extent possible it will draw upon existing work, but much additional work needs to be done in the area of coal supply economics.

Jan 1, 1977

By P. G. Martin

"As the speed of business has continued to increase over the last decade, the focus on real-time control of the performance of both stationary and mobile assets has become an increasing priority. Traditionally the maintenance team has been focused on the management of the availability of assets while the operations team has been focused on the throughput of those same assets. Typically operations and maintenance teams worked almost independently in spite of the fact that they were both working with the same assets. Part of the problem has been their traditional performance measures which have often been diametrically opposed. Recent advancements in the area of real-time performance measures and decision support have helped to drive higher levels of collaboration between operations and maintenance leading to real-time asset performance control and higher levels of business performance. This paper will explore the forces driving the need for changes, present an effective approach to the definition of the most appropriate business performance measures, and examine the effectiveness of contextualized real-time decision support resulting in asset performance control. TRADITIONAL APPROACHES TO ASSET PERFORMANCE MANAGEMENT In most industrial operations the phrase asset performance management is synonymous with maintenance of the industrial assets. This is the way industry has viewed asset management and asset performance management for decades. This is a very limited perspective that is serving to constrain the profitability of industrial operations. As industrial organizations began to form following the Industrial Revolution, the complexity of the operations forced an organizational design based on specialization. No single person could understand all of the aspects of an industrialized operation. This was particularly true at the plant floor level where the operation and maintenance of the industrial equipment required very different skillsets and training. To accommodate the vast differences most industrial organizations set up operations teams to run the equipment and maintenance teams to keep the equipment available to the operation. Both teams were dealing with the same industrial equipment but from very different perspectives and with very different performance measures. Typically the operations team was measured on maximizing the output of the equipment – or throughput. On the other hand the maintenance team was measured on the uptime – or availability of the equipment."

Jan 1, 2015

By G. R. Denham

Innovative designs, mining, construction and reclamation practices are used at PT Newmont Nusa Tenggara's Batu Hijau mine on Sumbawa Indonesia to develop a cost-effective, environmentally sound, stockpile and dumping system. The mine production rate is over 200 million tonnes per year (50 million tonnes processed with 150 million tonnes being stockpiled for processing later or placed in waste dumps). Dump development for over 150 million tonnes per year in a mountainous, tropical environment, while meeting environmental and permitting requirements is not an easy task. The effective implementation requires innovative techniques and practices from every department of the mine.

Jan 1, 2002

By W. P. Stroud, R. S. Dennen

A ground penetrating synthetic pulse radar system has been used by the US Bureau of Mines to probe into a coal pillar to locate hidden structures or anomalies. Direct matrix inversion was used to obtain a velocity image of the interior of the pillar. The reconstructed image showed the existence and location of a relatively low velocity material within the pillar. Core samples were taken from the pillar in a region surrounding the low velocity material. Analysis of the cores showed the presence of a clay vein coinciding with the low velocity material imaged in the tomogram.

Jan 1, 1992

By Steven W. Hunt, Jane A. Kettler, Barry R. Doyle

A sewer tunnel being constructed through an urban commercial area was to pass the site of a former gasoline service station. The site was known to have contained leaking underground storage tanks. An environmental assessment of soils on the alignment was performed, and measures were implemented to handle expected contaminants. Despite these precautions, an explosion occurred in the heading when liquid gasoline was encountered. Four workers were injured. This paper presents the findings of an investigation into the cause of the explosion, and examines how concerted efforts by the parties involved failed to prevent it. The level of guidance provided by OSHA Code provisions for tunneling in gassy conditions is discussed.

Jan 1, 1997

By I. Iwasaki, H. Dho

The role of sodium silicate in the anionic flotation of a Florida phosphate ore was investigated using laboratory continuous flotation tests, frothabiliry tests and SEM observations. In the absence of sodium silicate, Ca I+ promoted the unwanted activation of quartz by forming calcium bearing precipitates. The addition of sodium silicate enhanced the flotation efficiency through: 1) the removal of impurity minerals and calcium-bearing precipitates from quartz surfaces by dispersion, 2) drier and more persistent froths stabilized by oily droplets containing calcium silicate precipitates, and 3) higher specific flotation rates of phosphate relative to quartz, leading to faster flotation rates and increased selectivity of separation.

Jan 1, 1991

By Donald L. Meredith, Jeffrey Harris, Donald A. Stanley

Principal Components Analysis (PCA) is a versatile, multivariate statistical method that the Bureau of Mines is applying to mineral processing data to achieve data simplification and pattern recognition. The principal components are obtained from an eigenanalysis of the data matrix. To achieve data simplification PCA replaces a larger number of measured variables with a smaller set of principal components and at the same time removes a significant amount of experimental error. Data simplification and error reduction make PCA useful in process control. Plots of the individual principal components form the basis of a pattern recognition technique that allows detection of significant variations in the structure of the data. These applications of PCA are illustrated with appropriate mineral processing data.

Jan 1, 1993

By Z. Eisenstein, H. Heinz

INTRODUCTION Contemporary underground transit systems often require cross sections which are not adaptable to shield tunnelling. Due to the frequently large dimensions of these cross sections, which are normally situated at shallow depths and in soft ground, full face advance is not feasible because of ground control and construction requirements. Ground deformation and face stability are controlled by "staged excavation", which consists of sequentially driving smaller, specially arranged, individual headings hence avoiding full-face excavation. Shotcrete is normally used for initial support and these tunnels are frequently described as applications of the New Austrian Tunnelling Method (NATM). Figure 1 illustrates the relative size of large cross section tunnels with respect to conventional shield tunnels. Within the scope of this paper, 'large' cross sections are defined as those whose continuous (i.e., without intermediate pillar support) cross sectional excavated area exceeds 60m2. This definition includes most double track highway, railway and subway tunnels, subway stations and some single track railway tunnels. Excavation schemes which have been more frequently used for continuous cross sections (i.e., with no intermediate pillars) are presented in Figure 2. This classification is an extension of that presented previously by Eisenstein et al. (1986). The symbols used for classifying the excavation schemes are formed by the letter T (for "type"), followed by a number, which represents the number of excavation stages fully embraced by a shotcrete ring, termed "cells" by Lessmann (1986). The numbers inside the cross sections in

Jan 1, 1989

By G. Knight

It is shown that the dust exposure of all underground workers varies greatly from day to day even though each man did the same job in the same working place each day. The variability follows a logarithmic normal distribution with a geometric standard deviation of about 1.6 for the three dust assessments; total respirable dust, respirable combustible dust and respirable quartz dust in both mines studied. The variability was homogeneous for all men and most jobs. The differences between men doing the same job was found not to be significant and it is suggested that the dust sampling program should determine the average for each job and use this as the best estimate of the exposure for each man.

Jan 1, 1980

By Joe M. Bryan, George E. Rodger

The development of small precious metal mines in the western states has been directed at heap leach operations. Crushing plants are an essential adjunct to heap leach operations. They must meet environmental air quality regulations which generally follow a similar pattern from state to state. Prior to mine construction a permit must be obtained and an operating permit granted during or shortly after the start-up period. The typical construction permit application consists primarily of drawings, specifications and an explanation sufficient to indicate that the mass of particulate matter entering the atmosphere is below minimum standards. The operating permit may be granted following demonstrations that air emission control equipment or methods comply with information submitted in the construction permit application.

Jan 1, 1987

By Anthony D. Hammond

Geographic Information Systems (GIS) are powerful analytical and data display tools for mining industry management, capable of linking spatial features with tabular data and integrating communications across departmental boundaries. This GIS application concentrates in four technical areas of underground mining: ownership and mineral claims; exploration management; production; and mine safety. GIS provides land and exploration managers with the ability to consolidate and archive claim data and to georeference property maps defined in local coordinates into world coordinate systems. It facilitates optimal siting and querying of service installations and refuge chambers relative to production centers. GIS's proximity analysis identifies areas of potential safety concern and points to and maps the shortest routes to emergency exits, facilitating the prompt evacuation of mine personnel.

Jan 1, 2002

By J. Pereyra, M. DeMarco

"INTRODUCTION It can be vital that bolted joints holding subassemblies together remain secure. Bolts should resist the loosening effects of vibrations and dynamic loads yet need to be easily removable during maintenance. When a threaded fastener is subjected to vibration, the rapid movement causes a lowering of friction against the threads and a subsequent loss of preload. The loss of preload allows the fastener to vibrate loose and possibly fall out. As the diameter of fasteners increase desired preload becomes increasingly more difficult to achieve. Input torque requirements for achieving proper bolt preload is exponentially related to any given fasteners diameter. This means that specialized tooling or bolting practices are usually required to attempt the tightening of fasteners to reach their required preload. Traditional methods can cause problems with joint integrity and do not provide consistent bolt load across the bolted surface. BOLTED CONNECTIONS A failed critical bolted joint can lead to high maintenance costs, machine downtime, and risk to worker safety. Control of the clamp load in a bolted joint is vital. However, when faced with a problem joint, it is not surprising that the design engineer will not have an answer if asked about the clamp load. Torque calculations must always be based on the existing conditions that often are vague. Unless all parameters are correct, the calculation will be unreliable. Examples of parameters are: • Thread condition of the fasteners • Hardness of contact surface • Material (steel, aluminium, copper, etc.) • Extra friction from a locking fastener • Extra friction from an adhesive • Lubricant on the thread • Type of bolt head (flanged, regular or serrated) • Surface coating of the bolt • New or reused fastener During tightening, bolts are subjected to both tensile and torsional stress. The total stress in a bolt can be calculated using the formula: Total stress = vsx2 + 3txy2 In order to maximize the desired tensile stress (sx) it is vital to minimize the torsional stress (txy). Tensile stress (clamp load) is achieved when the bolt is axially elongated. Unwanted torsional stress (twisting) in bolts arises during tightening due to thread friction. High thread friction increases torsional stress and causes yielding at lower clamp load levels than normal. A lubricant is necessary to minimize the malign torsional stress. However, many commonly used bolt-locking systems are based on increased thread friction (deformed nuts, adhesives, etc). To minimize thread friction and concurrently safely secure the joint has often incorrectly been considered impossible. The use of locking systems that increase thread friction is the single most common reason why the full capacity of bolted joints is not utilized. The following example illustrates the problem."

Jan 1, 2015

By Steven W. Hunt, Steven B. Fradkin, Roger J. Maurer

During the 1980s and 1990s, twenty deep shafts were constructed in Milwaukee to depths from 85 to 91 m (280 to 300 feet) through soil and weak rock thicknesses ranging from 37 to 69 m (122 to 227 ft). Adjacent compressible soils, settlement sensitive structures and high groundwater levels required that shafts be constructed without dewatering. Contractors attempted several methods of ground support and groundwater cutoff. Significant problems developed during construction of 11 of the 20shafts. One shaft collapsed; groundwater blow-ins occurred at five of the shafts; and seepage caused unfrozen windows at three of the freezewalls. Ultimately, combinations of grouting and ground freezing were utilized to complete all of the shafts into bedrock. This paper discusses the main design and construction challenges experienced and the lessons learned.

Jan 1, 2003

By Robert A. Haney

During the last ten years, longwall mining systems have undergone many changes. Panel widths and lengths have increased. Longwall faces have become more automated. Average production from individual longwall panels has increased from 1,000 to 3,600 tons per shift. To control the dust generation resulting from the higher production, longwall dust control systems have integrated various dust control techniques. Systems designed to control dust generated at the crusher/stageloader, shearer, and supports are common to most longwall faces. A survey was made of the dust controls that are currently in place on all the longwalls in the U.S. This survey addressed the types of controls used to reduce dust generated at the crusher/stageloader, shearer and roof support movement. Additionally, information on face ventilation rates, cutting cycle and level of automation was obtained. The purpose of this paper is to review the dust control practices that have been implemented throughout the United States and to identify those controls that are being used on high production longwall faces. Additionally, a model is used to demonstrate how ventilation and automation affect occupational exposure. Automation of roof support movement can offer some of the greatest reductions in occupational dust exposures. While technically feasible, its full benefit has not been fully realized by the industry. Until technology to fully automate longwall mining systems becomes more reliable, future dust control systems must rely on increased ventilation, application of headgate dust collectors, improved shearer dust controls and improved shield dust suppression systems.

Jan 1, 1995

By J. C. Barker

Alaska, with about 74% of the US continental shelf, is largely unexplored for placers in its vast shallow marine waters. Nevertheless, there are numerous occurrences of marine minerals including gold, platinum, and cassiterite. Offshore dredging has recently begun in the Nome area. State and Federal agencies are preparing additional acreage for leasing. With 76,200 km (47,300 miles) or 54% of the US coastline, Alaska is a vast, largely unexplored frontier for shallow-water marine placers. Despite the general lack of mapping and only sporadic past prospecting, many prospects are known and a major mining operation for gold has recently begun offshore of Nome. Due largely to the demonstrated success of the Nome operation, the US Minerals Management Service is preparing to conduct a lease sale of additional acreage further offshore from Nome. And future sales are being considered elsewhere by both the Federal and state leasing agencies.

Jan 1, 1990

By Shahzad Moosa, John M. Pitt

Statistical variability in rock strength can be evaluated by rapid, inexpensive ultrasonic pulse velocity measurements, an important consideration since rational probabilistic design in rock is often hampered by the cost of obtaining sufficient strength data. Experimental ultrasonic pulse velocity measurements on a set of 96 limestone specimens showed two distinct statistical populations. Both populations followed Weibull distributions, with flexural strength distributions paralleling pulse velocity distributions. Thus, experimental results suggest that strength variability may be predicted from a few rationally selected strength measurements and several ultrasonic tests. The correspondence between strength and velocity may then be used to develop an experimental transformation function, allowing the development of a statistical distribution function for strength based on the known statistics of velocity. Comparison of experimental groups with full sets of corresponding strength1 velocity data showed the technique offers a fairly accurate description of the statistics of strength.

Jan 1, 1986