Search Documents

By Ralph Loyd

One of the principal responsibilities of the California State Geologist is to provide local governments with maps and information regarding mineral resource occurrences within their jurisdiction. The primary objective of this effort is to furnish basic data that is essential in planning for and accommodating wise development of mineral deposits that are important to the economic well-being of the region, state, and nation. Local government agencies are required by law to incorporate the information provided by the State Geologist into their general plans and formulate mineral resource management policies that emphasize conservation and development of mineral deposits. The Mineral Land Classification program was initiated by the State Geologist in 1977 under authority of the California Surface Mining and Reclamation Act (SMARA). To date, about 33,000 square miles of land have been classified for mineral resource potential. Most of the mineral land mapping has been conducted in three principal areas: (1) metropolitan areas of the state where urban encroachment has greatly diminished available supplies of construction aggregate; (2) Sierra Nevada foothills, a region that is undergoing dramatic population increases; and (3) the Mojave Desert and Great Basin regions, where large Federal land withdrawals are pending that could preclude mining. Mineral land classification studies address the overall mineral potential of a region through the identification of local and regional geologic factors that control or influence the formation of mineral deposits. These studies are field-intensive surveys that enable project geologists to gain first-hand knowledge about the nature and distribution of mineral deposits in a given area and portray that information accurately in map form. This paper summarizes the progress made in the Mineral Land Classification program in the metropolitan, Sierra Nevada foothills, and the Mojave Desert/Great Basin regions of California. Selected projects from each area are discussed in detail.

Jan 1, 1995

By Samuel Sigman, Martin M. Cooper

A basic ingredient for rapid tunnel excavation is material handling. In construction of tunnel projects in urban areas material handling requires additional input to maximize performance. Urban projects share the same problems experienced in all tunnel construction and they must be dealt with. Howeve.., Urban constraints add a larger dimension. APPLICATION ENGINEERING A MUST A word of caution. To achieve increasing speed of excavation in tunnels whether in Urban areas or elsewhere will require much creative thought and energy. It would be a false premise to assume that major breakthroughs will result from this conference, or shortly thereafter, or to hope that a success here or there can translate into a universal solution. The reality, as we see it is that rapid progress and great economies will accrue on any given project only if effective application engineering is carried through. By all means take advantage of past experiences but, do not at the peril of costly undertaking, blindly accept the program of a successful job elsewhere as automatically suited to your project. Tunnel construction in urban areas is at best a difficult undertaking made more difficult in this period of greater awareness of environment, of conservation and of the quality of living by sophisticated urban communities,. A construction job represents a necessary nuisance to urban communities. To minimize this nuisance many regulatory laws are adopted. These regulations can and do slow down tunnel jobs and pyramid costs.

Jan 1, 1974

By R. J. Roman

Introduction This paper attempts to describe the characteristics of the industrial minerals segment of the minerals industry that make it different from the other segments. Also described are the trends, strengths, and shortcomings in the industrial minerals segment. This may help professionals in the minerals industry determine if there is a place for them in industrial minerals. Industry Overview It is difficult to generalize when describing the industrial minerals industry. Some products, such as cement and potash, are produced exclusively by large, well capitalized and technically sophisticated companies. Others, such as sand and gravel, are generally produced by small, family-owned companies operating on a shoestring budget. Still other products, such as feldspar, are produced by both types of companies. Not only are the companies vastly different, the products and marketing of their products are also different. Industrial mineral products are sold based on their physical characteristics (abrasives), or their chemical characteristics (trona), or both (glass sand). Marketing can be direct by the producing plant, a corporate office handling products form several plants, or through distributors. The geologic, mining, and processing skills needed can be minimal or sophisticated. There can even be large differences in the technical skills needed in two plants producing the same product. One feldspar producer may only need to mine and grind his ore, while another may use a delicate flotation process. One easy generalization is that there are industrial mineral operations in all geographic locations. A second is that industrial minerals offers more opportunities to entrepreneurs than the metals field because of the variety in the sizes and types of operations. Industry Growth Industrial minerals must be considered a mature industry. Consequently, little exciting growth can be expected. Over the past 30 years, industry sales have grown at a rate of 6.2%, compared to a 6.7% growth rate of the GNP (Kliff, 1978). A 3.8% growth rate has been forecast for the remainder of this century. The fortunes of those plants producing a product for local consumption will depend on the prosperity of the local economy. The fortunes of those plants that sell into the national market will depend on their competitiveness in their industry. Major industrial mineral products are shown in Table 1. The first three commodities account for 66% of the industrial minerals market. Typically, deposits of stone, sand and gravel, and the limestone, silica, and clay needed for cement are easy to find and mine. Role of Mining Engineers and Geologists Because a sophisticated techcical knowledge of geology or mining is not required, very few geologists and mining engineers are employed in industrial minerals. Geologists working for these companies function less as geologists than managers and executives dealing with permitting and land acquisition. Likewise, mining is done mostly by open-pit methods. It is generally supervised by an individual experienced in the operation and maintenance of heavy equipment, not a mining engineer trained in rock mechanics or computer methods of mine planning. What of the geologists and mining engineers employed by the industrial minerals industry? Many gained their positions as a result of their experience dealing with the regulatory agencies that control the operations of all mines and mills. Their technical expertise in geology or mining becomes only a side benefit. Finding and mining industrial minerals does not generally require the concentrated efforts of geologists and mining engineers. But the processing of the ores does

Jan 2, 1985

By Robert P. Mahoney, William J. Roe

Polymers of a wide variety of composition are used in coal and mineral beneficiation. Applications include flocculation and coagulation in thickeners, filtration enhancement, mill scale control, dust control, ore leaching improvement, and pond management. The proper chemistry of the polymer is determined by many factors, including the nature of the process, mineral type, and respective performance requirements. This paper provides an overview of the various current applications of polymers in mineral processing, and a description of the applicable polymer chemistries which find utility in these applications. Examples of structure/performance relationships are discussed.

Jan 1, 1994

By P. Somasundaran

The use of chemical additives in ultrafine grinding will be reviewed in this paper for the case of grinding of quartz in solutions of surfactants and inorganic electrolytes including some dispersants under different conditions of pH and ionic strength Mechanisms are examined by correlating the grinding effects with those obtained for the influence of these chemicals on zeta potential, pulp fluidity and flocculation/dispersion characteristics The analysis suggests grinding depends mainly on the state of aggregation of the ground products inside the mill and pulp fluidity Implications of the observed effects on ultrafine grinding in general are discussed

Jan 1, 1983

By C. J. Lewis

Commercial lime plants in the United States and Canada are depicted in Figure 1. The sources of lime available to Nevada and bordering states are rather few. Chemstar Lime has plants at Apex, Nevada and Nelsen, Arizona. Continental Lime, Inc. has plants at Tacoma, Washington, Townsend, Montana and Delta, Utah. However, Continental Lime has a new rotary kiln installation underway near Wendover, Nevada. This plant is scheduled to come on stream in the fall of 1989.

Jan 1, 1989

By D. Malhotra, K. Purdy, G. Ramadorai

INTRODUCTION Today, flotation is clearly the dominant mineral concentration method. Since it is a relatively selective process, it is used for almost all sulfide minerals. A recent U. S. Bureau of Mines study indicated that approximately 225 million metric tons of sulfide ore was processed in 67 plants in the United States in 1980 (USBM Staff, 1981). There were over 100 plants processing copper ores in the world (Bassarear, 1985). Sulfide ores containing lead, zinc, copper, molybdenum, precious metals, cobalt, nickel, and iron are generally separated and concentrated by flotation. This chapter briefly reviews the plant practice related to the recovery of the above-mentioned sulfide minerals with emphasis on chemical reagents used for the production of marketable-grade products. PROCESSING OF SULFIDE ORES It is beyond the scope of this chapter to review the milling data for operating plants which have been extensively covered in literature (Tveter and McQuiston, 1962; Rausch and Mariacher, 1970; Weiss, 1985; Crozier, 1979). However, the following generalizations can be made regarding the processing of sulfide ores: 1. The primary grind is targeted to produce as coarse a product as necessary to provide an economic degree of liberation. 2. The concentration process, generally flotation, is designed to produce a concentrate consisting predominantly of valuable minerals and a middling fraction which may require further grinding to produce an optimum release of minerals. 3. The chemical reagent suite (collectors, frothers, etc.) for the separation of sulfide minerals from gangue minerals is generally complex. Total reagents used in the flotation process can be as high as six to eight, as is the case for lead and molybdenite separation from complex sulfide ores. 4. Chemical reagents are generally expensive because of the high selectivity for sulfide minerals. The process flowsheet is dependent on several factors, including ore grade and mineralogical composition. Generic process flowsheets for processing different sulfide ores have been developed for discussion in this chapter. However, there appears to be a consistent relationship between the reagent combination choice and the mineralogical composition of the ore (Tveter and McQuiston, 1962). These are covered in detail in the following sections. LEAD AND ZINC Galena (PbS) and sphalerite (ZnS), which commonly occur together, are the only minerals of lead and zinc, respectively, in most primary deposits. Feed ore grades are typically 1 to 5 percent Pb and 1 to 10 percent Zn. Very often economic quantities of copper and precious metals, silver and gold, also occur with these base metals.

Jan 1, 1986

On my arrival in New York after the Russian examinations John D. Ryan, president of Anaconda, asked me what my plans were. I told him I wanted to be useful somehow in the World War that we had entered while I was away, but I did not know how. Ryan and Thayer told me that the new American Air Corps was gathering a group of executives, most of them young, to go to France as Army officers to help with the industrial side of our aviation activities. This would include construction of military airports, maintenance, and supply for our rapidly growing Air Corps. They thought I might be accepted in this group of about 30. It seemed to be just what I wanted, and I put in my application at once. My application was accepted about three weeks later and I was told to come to Washington to take physical and other tests and to meet others of the group. I liked them. They were a cross section of competent American manufacturers, bankers, automobile executives, and merchants. I was the only miner. I had many discussions in the days in Washington with members of our organization and others I knew who were going into war service. Attitudes were very different from those 55 years later. There was no discussion as to whether war was right or wrong. We were in it and must do all we could to help. At the same time there was a holdover from the days when, at least for the elite, war was high adventure. Even the most high-minded did not then realize that war is a horrible form of wholesale murder and, in 1917, it would have been treason to suggest this. I had two weeks before our industrial group was to start work which gave me time for a hurried trip to Berkeley where Dorothy and I announced our engagement.

Jan 1, 1976

By Paul J. Henkels

Synthetic gypsum is the calcium sulfate co-product of a number of industrial processes. Synthetic gypsum utilization as an alternative to the naturally occurring mineral continues to grow in the gypsum industry. In particular, flue gas desulfurization (FGD) gypsum produced by the electrical utility industry has had a significant impact and a far-reaching effect on the gypsum wallboard manufacturing industry. This paper will discuss the various synthetic gypsum sources verses natural gypsum and highlight issues of use in gypsum wallboard and related products.

Jan 1, 1999

By D. M. Bodily, V. J. Hucka

INTRODUCTION Interest in the recovery of methane from coalbeds has increased rapidly over recent years, because of its potential as an energy resource and to alleviate pollution and safety problems. The resource base of coalbed methane in the United States has been estimated at 11.2 Gm3, roughly equivalent to 20 years consumption (Mroz et al., 1983; Kuuskraa and Brandenburg, 1989). Methane contributes to the adverse environmental impacts of global warming, tropospheric ozone formation (smog), and potentially stratospheric ozone destruction. Association of methane with coal has always presented a safety problem in mines due to the potential for explosions. The rate of release of methane depends on the amount adsorbed by the coal, the adsorption isotherm for the coal, and the size of the coal particles. Mining operations can affect the particle size distribution and the production of fines and therefore the rate of release. The time the mined coal remains in the mine may also be important in determining total emissions. The methane content of some Utah coals was determined in this study. The methane content of the coals is compared with the chemical and physical properties of the coals and the properties of the seam and neighboring strata. Correlations are developed to better understand the formation and retention of methane by these coal seams. METHANE FORMATION IN COALBEDS Three mechanisms for methane formation may be considered: (1) nonbiogenic formation, (2) formation by anaerobic bacteria during plant material deposition and the early stages of diagenesis, and (3) formation from pyrolysis of coal material during coal maturation. Nonbiogenic formation by thermal processes involving carbon- and hydrogen-containing compounds has been proposed as a mechanism for methane formation in the earth. It is not likely to be of importance where other fossil fuel materials are present. Coal would not survive the temperatures required and hence the methane would need to migrate and be trapped by the coal seam. This mechanism is unlikely for coalbed methane. Formation of methane by anaerobic bacteria undoubtedly occurs during coalification, but the methane may not be trapped until the pore system of the coal is developed, and would likely be displaced by methane formed during further coalification. Methane formed by maturation of the coal material as it progresses from peat to coals of various rank is the most probable mechanism for the formation of coalbed methane. Most of the methane is adsorbed onto the walls of microvoids in coal. It has been estimated that the surface area of one kilogram of coal is between 20,000 m2 to 200,000 m2. Surface area measurements depend on the coal and also on the method of measurement. At 20 atmospheres, in some coals, the adsorbed methane is 10 times greater than methane as a free gas. At 100 atmospheres the adsorbed gas can be as densely packed as a liquid. The volume of methane gas held in coal depends on the volume of gas that exists as a free gas and the adsorbed gas capacity. The volume of free gas in the coal can be calculated from the kinetic theory of gases (methane can be assumed to be an ideal gas because errors would not be greater than 1 % for normal mining pressures). Langmuir (1916) derived an equation for the adsorption of gases on uniform surfaces and this is applied to the adsorption of methane on coal:

Jan 1, 1993

By L. Darkwah

The use of explosives in coal mining inevitably results in oversize, midsize and undersize (fines) products due to fragmentation. The oversize can be broken into smaller sizes by further processing. However, the undersize have a negative affect on the efficiency of a mining operation. Therefore, limiting the amount of fines can be economically crucial. This paper concerns investigations aimed at reducing fines generation in coal mining. Inherent fractures were identified as one of sources of fines generation. This paper is centered on establishing a relationship between the fracture occurrence, the explosive properties and the blast outputs, which are evaluated in terms of the fines generated.

Jan 1, 1998

By Stephen W. Denton

Planning a mining operation in Alaska will involve the investigation of many parameters common to mine planning anywhere. However, there are some unique circumstances that must be recognized when one considers development of mining operations in Alaska. This paper will not attempt to provide a blueprint for mine planning in Alaska, but hopefully will provide a better understanding of the truly unique nature of the northern latitudes. Given this understanding, the mine planner can better assess the potential hurdles along the road to a successful mining operation. The regulatory trend towards uniform standards for mining throughout the United States exemplifies the necessity for Alaska to prove its unique position in the natural resources picture. The factors which make Alaska truly different from the "Lower 48" can be summarized by four points 1) Remoteness and Size 2) Seasonable Extremes 3) Geologic Immaturity 4) Vegetation and Wildlife

Jan 1, 1984

By Fred N. Kissell

INTRODUCTION During the last few years, several new ventilation developments have attracted the interest of mining engi¬neers. Some of these developments are applicable pri¬marily to hard-rock mining, while others are more applicable to coal mining. STOPPINGS Parachute Stopping The parachute stopping is a new type of quick-erect stopping that is intended for temporary use in hard-rock mines (Kissell, Thimons, and Vinson, 1975). As shown in Fig. 1, the stopping is shaped very much like an ordinary parachute, with a canopy of impermeable fabric that is sewn to regularly spaced straps running to a common point. To erect the stopping, the straps are attached to a fixed anchor point such as a roof bolt, and the edge of the canopy is lifted into the moving air¬stream. The airstream pops the parachute canopy into place, and the differential air pressure across the stop¬ping holds it in place, forcing the fabric against the walls, roof, and floor of the mine opening. The principal advantage of the parachute stopping is that it requires only a few minutes to install, making it a great time-saver for emergency use or for day-to¬day changes in ventilation during the production cycle. However, the parachute stopping does require some minimum air velocity to lift it and some minimum differential pressure to hold it in place. For a fabric weighing 0.27 kg/ m2 (8.0 oz per sq yd), the minimum air velocity is about 0.5 m/s (100 fpm), and the mini¬mum differential pressure is about 0.05 kPa [0.2 in. water gage (WG) ]. There is always some air leakage around the stop¬ping, mainly depending upon the extent to which pipes or other obstructions encumber the airway and prevent good sealing. Leakage of a few cubic meters per second (a few thousand cubic feet per minute) can be expected, unless foam is used to improve the seal at the edges of the canopy. Quick-Fix Blowout Stopping The quick-fix blowout stopping is a variation of the parachute stopping (Thimons and Kissell, 1976), and it is used in the proximity of blasting operations. This type of stopping is designed to be blown out easily by the blast forces, and it may be reinstalled quickly and easily. The long high-strength straps of the parachute stopping are replaced by groups of short straps that tear easily. These straps are attached at six equally spaced locations around the perimeter of the canopy. To erect the stopping, one strap of each of the six groups is fastened to the mine wall, roof, and floor by using spads, by setting pins with a powder-actuated gun, or by tying the straps to some firm anchor point. Once the straps have been attached, the differential air pressure across the stopping, which must be at least 0.025 kPa (0.1 in. WG), forces the stopping perimeter against the mine walls, thus creating the air seal. It is the self-sealing feature of this stopping that makes it a significant time-saver. Only a few attachment points are needed; in many cases, four attachment points are sufficient, since the stopping naturally tends to form a seal with the airway surfaces. When nearby produc¬tion blasting exerts excessive forces on the stopping, one or more of the straps tears away from its attachment point, protecting the stronger canopy from damage. Damage-Resistant Brattice The damage-resistant brattice is a stopping that is designed for use in mines such as salt and limestone mines where the differential pressures are low and the roof is relatively flat. As shown in Fig. 2, the damage-resistant brattice consists of a series of brattice panels that are hung vertically and joined by Velcro® connections. When the brattice is subjected to strong blast forces, the Velcro® connection peels apart and allows the panels to open without incurring damage. The Velcro® connections can be resealed by hand within a matter of minutes. Such damage-resistant brattices have withstood the blast effects of 318 kg (700 lb) of ammonium nitrate-fuel oil (ANFO) explosive detonated as close as 91 m (300 ft) from the brattice. Ordinary brattice cloth is used for the panels, with a 51-mm (2-in.) wide strip of Velcro® hooks sewn along one edge of the length, and a 51-mm (2-in.) wide strip of Velcro® pile sewn along the other edge. Both the hooks and the pile are sewn onto the same side of the brattice cloth. The resulting Velcro® seal formed be¬tween adjacent panels is perpendicular to the brattice itself, and the leading edge of the seal can be directed either toward or away from the blast forces; the brattice works equally well in either case. To hang the brattice, panels of brattice cloth about 0.9 m (3 ft) longer than the height of the airway are cut from a 1.8-m (6-ft) wide roll. The additional 0.9 m (3 ft) of brattice cloth allows 0.3 m (1 ft) for attachment to the roof by means of a board, with 0.6 m (2 ft) for forming a good air seal at the floor. Each brattice panel is wrapped once or twice around a 51 X 102 mm (2 X 4 in.) or 25 X 76 mm (1 X 3 in.) mounting board that is 254 to 305 mm (10 to 12 in.) shorter than the width of the panel. For convenience in

Jan 1, 1982

By Andrew S. Lain

Before you begin mining aggregates in Oklahoma, you must first look at the market and ask these questions: (1) Is there a need for additional aggregate production? (2) Can we produce the aggregate efficiently enough to compete? (3) Is the deposit close enough to the market? If you can answer "yes" to each of these three questions, then you are ready to start the process for mining aggregates in Oklahoma. The first consideration to be made is whether the aggregates produced will need to meet state specifications. If you do not want to meet state durability standards, there are numerous formations you can mine and produce aggregates. We will deal only with the formations that will meet state durability standards. These formations are located in the southern half of Oklahoma and in the Tulsa area. Some of the formations that contain limestone, dolomite, and sandstone that will meet state durability tests are West Springs Creek, Kindblade, McKenzie Hill, Butterly-Royer, and Rush Springs Formations. Granite and rhyolite also are found in Oklahoma and can be used as construction aggregates. Once an area has been identified as having durable material, and drilling has verified its properties, a permit must be secured from the Oklahoma Department of Mines, Oklahoma Department of Environmental Quality, and any other applicable agency before construction of a plant occurs. There are many different brands of crushers available, but all work on one of two crushing principles-either compression breakage or impact breakage. Each type has its application in different industrial-mineral types and the desired end product. A typical small crushing plant would start with a jaw crusher for primary reduction, and then employ one standard cone and one shorthead cone for secondary reduction. One grizzly would be in the circuit with one finished-product screen and three to four finished-product stackers. Natural sands and gravels are found in rivers and old river channels. These too need to be tested to see if spec product can be produced. All of our sand operations have very little gravel; thus, we do not process the gravel. The sand is processed through classifying tanks for gradation.

Jan 1, 1999

By T. S. Govindan

The first step in energy conservation in any industrial plant involves implementing many of the day-to-day "house-keeping" items such as fixing leaks, turning out lights, etc. When this step has been accomplished, additional opportunities require a detailed analysis of the energy systems, evaluation of risks and costs, and assignment of priorities. Examples of conservation schemes drawn from the experience of Du pont's Energy Management Consulting Services will be discussed. The utility of heat balances for kilns and dryers in minerals processing will be outlined. The inputs needed from Management for the success of conservation efforts will be discussed.

Jan 1, 1978

By Georges E. Vaillant

Air pollution control in primary aluminum smelter . Various processes are known for air pollution in electrolysis plants. Mainly two systems have to be taken into consideration: -Treatment of concentrated gases collected directly from hooded pots. This is normally achieved by either dry or wet process. This is not the object of this paper as these processes have been already described. -Treatment of low concentrated fumes. A certain amount of gaseous and solid fluoride (35 % of total fluor pollution) goes out of the hooded pot. Gases commonly called secondary fumes are generally treated by wet process. The object of 'this paper is to describe two plants with specific treatment for secondary fumes. 1/ A plant in operation in Vlissingen (Netherlands) for PECHINEY. 2/ Presentation of tests carried out by a specialized Company. The results of such tests have been used for the design of the scrubbers presently under construction for ALUMINIO ESPANOL San Ciprian (Spain).

Jan 1, 1978

By S. M. Hsiung, Wen H. Su, Syd S. Peng

This paper examines the interaction problems of multiple seam mining by combining underground investigation, laboratory testings, and numerical modeling. One case of multiple seam interaction that occurred recently in West Virginia was carefully studied. Causes for the interaction problems were identified and the corresponding mining recommendations were proposed. The principle of pillar columnization and the effect of a remnant pillar on mining operations in the underlying and over- lying seams were also carefully examined. Considerable attention was given to the effect the pillar size, the pillar width, the coal stiffness, the extraction ratio, the degree of inhomogeneity in the interburden, the overburden thickness, the mechanical properties of the interburden rocks, the strata inclination, the interburden thickness, and the in-situ horizontal stresses have on the pillar load transfer mechanism.

Jan 1, 1986

By David M. Spatz

Anyone who scans the modern literature will realize that concepts of leadership have changed during the past few years. And like change in so many areas of our culture, change has been rapid in the perception of leadership. Many traditional leadership traits are still highly regarded and many of the longstanding personal qualities that improve leadership abilities continue to be effective. In the past, though, leaders could rely on dominance, intimidation and fear to accomplish their goals through the actions of others. In contrast, effective leaders today build relationships, provide vision and guidance, and strive for communication, cooperation, trust and employee satisfaction. Earnest leadership involves moral issues like honesty, integrity, fairness, empathy and respect. Modern leaders guide, facilitate and coach, rather than command and direct. But how well equipped are managers in the mining industry to meet the leadership challenges that lie ahead? More importantly, is he or she becoming a better leader? This article outlines steps to becoming a more effective leader. Management consultants stress that the changes that lie ahead will demand swift organizational adjustments and managers who are equipped to lead during times of change (Boyett and Conn, 1991; Hesselbein et al., 1996; White et al., 1996 and Kotter, 1997). Becoming a better leader begins with self-assessment and a commitment to unify all who depend on one's leadership abilities. Simply defined, leadership is leading others. Contrary to common practice, leadership is not about advancing one's own career but about bringing out the best in others. The beauty of modern leadership, however, is that the path of serving others creates synergies. They benefit everyone, including the leader, those the leader manages, upper management and company shareholders.

Jan 1, 1998

By Kai Nielsen

In underground mining coarse muck and large boulders lead to ineffective utilization of costly mining equipment, and extra expenses and delays caused by secondary blasting. Cost analysis in some Norwegian mines shows that these extra expenses may amount to 10% or more of total mine operating costs. A computer model has been developed for sensitivity analysis of underground longhole stope blasting. The basic idea of the model is : When increasing the blasting energy input and fragmentation costs, the fragmentation will be better. This will lead to cost savings for loading, hauling, secondary blasting and primary crushing. The blasting design giving the lowest overall costs will indicate the optimal practice. The model has been used with data from several underground operations in Norway. An example run with typical costs shows that the costs for drilling, blasting and secondary blasting are the most significant parameters in the optimization process.

Jan 1, 1986

By Fred A. Breu, Jerome C. Neyer, James F. Peters, John W. Critchfield

This paper describes experiences with methane and hydrogen sulfide gas encountered during design and construction of a sewer tunnel in rock, in Rochester, N.Y. Design explorations are summarized, including geologic setting, measurements of gasses in test borings, laboratory analyses of gas samples, and measurements of gas pressure and flow rates from a sealed borehole. Contract specifications regarding gas are outlined. Results of the Contractor's additional explorations and testing are presented, along with a description of selected equipment and provisions for ventilation and degassification.

Jan 1, 1985