Search Documents

By K. N. Han, M. C. Fuerstenau

Challenges in five major areas of hydrometallurgy are presented and discussed. These are: leaching low-grade oxide and sulfide ores; oxidative leaching of sulfide concentrates; processing refractory ores; bacterial leaching and processing: and secondary metal recovery.

Jan 1, 1989

By M. Robb, S. J. Bate, M. Boisvert

The never-ending quest for gold-bearing ore deposits is a primary industry in Canada, employing people of widely differing expertise. The exploration models for gold deposits are generally geologically complex and the targets have relatively small cross-sectional areas. These problems are compounded in Canada by the minimal outcrop exposure in most mineral provinces and the high percentage of water-covered areas. Naturally the chances of successfully delineating an economic gold deposit are very much greater if all parties involved can act as a team of explorationists constantly confemng amongst themselves particularly as the applicable disciplines generally overlap and complement each other. Three case histories (see Figure 1) are presented to illustrate this philosophy with emphasis placed on the role of the geophysicist in translating the exploration model as defined by the geologist into physically measurable parameters and identifying target areas with similar characteristics. The Conwest-Miminiska property in Ontario is a grassroots exploration play. Additional ore reserves needed to be delineated on the Salmita property in the Northwest Territories. At Laura Lake, near Chapais, Quebec geophysical methods were employed to trace thin high-grade mineral intersections under deep overburden and severe cultural interference.

Jan 1, 1989

By S. Zendejas-Mendivil, E. Pérez-Segura

The Cananea porphyry copper-deposit is the site of the second largest mining operation in Mexico. Mineralization is related to quartz-monzonite Laramide stocks that intrude volcanic and volcaniclastic Mesozoic rocks. The ore deposit is a stockwork and breccia-pipes system with Cu-Mo sulfides and pervasive quartz-sericite hydrothermal alteration. A study was made of the arsenic distribution in the mine and the ore-dressing plants. The arsenic (As) in the mine is related to a feldspathic quartz-porphyry type rock associated mainly with the breccia pipe structures (100-700 ppm As in the Veta 7 Breccia). There is vertical zoning, with As decreasing in the deepest part of the breccias. This As mineralization corresponds to a later sulfide hydrothermal stage. The concentrates are made of Cu, Fe and Mo sulfides and some minor quantities of As minerals. The most important copper minerals are chalcocite-covellite, bornite and chalcopyrite. Some of these minerals have 390-880 ppm As. The main As mineral is enargite[ [Cu2.97Fe0.06(As0.90 Sb0.01Pb0 01 )0.92 S4 051 and there are traces of stibioluzonite-luzonite I Cu, .95(Aso.4vSbu.49)0.9rfS4.07-Cu2 93(Aso.H4Sba.10)0.94S4.13] and of another stibioluzonite mineral type with substitution of As by Bi[Cu,96(Ascr,,'Sb0ccrB'OJ3jI~6S] These minerals contribute 80% of the As in the concentrates.

Jan 1, 1992

By D. E. Munson, T. M. Torres, D. A. Blankenship

The Thermal/Structural Interactions (TSI) In Situ Tests are a series of large scale, well instrumented tests that have been constructed at the Waste Isolation Pilot Plant (WIPP) in southeastern New Mexico. As a precursor to the TSI tests, a ventilation drift (Room D) was mined, drilled and instrumented. This room provided the contractor an excellent area to practice controlled construction methods and was a proving ground for construction monitoring and documentation methods. All gages in this first room have been monitored since their initial installation, which has provided a small, but representative, data base. These data also were the first to be available from any TSI area for analysis. This paper discusses the construction activities in Room D and the data generated from the construction and drilling. Deformation of the room is compared briefly to numerical calculations that used a rather simple creep model as a reference. The constitutive model for salt, it appears, must be improved before it can predict the underground deformations.

Jan 1, 1986

By Susan T. Bagley, Linda D. Gratz, Kirby J. Baumgard

The extensive use of heavy-duty diesel engines in underground mines has raised concerns about the potential adverse health effects to miners exposed to diesel particulate matter (DPM) which contains mutagenic and carcinogenic organic compounds. The purpose of this study was to compare the levels of DPM, biological activity, and polynuclear aromatic hydrocarbons (PAH) attributable to diesel engines in underground coal mines and similar data collected in engine laboratory facilities to assess whether laboratory data could be used to predict in-mine levels of diesel emissions. Mean in-mine DPM and SOF concentrations varied from 0.90 to 1.9 mg/m3 and 0.08 to 0.40 mg/m3, respectively. DPM-associated mutagenicity (mean) levels at two of the mines varied from 400 to 970 revertants/m3. Concentations of three PAH differed by up to four-fold between two of the mines, largely reflecting differences in DPM and SOF levels. The laboratory raw exhaust data were divided by 100 to obtain expected or predicted values for in-mine concentrations. The predicted DPM, SOF, mutagenicity, and PAH values based on laboratory samples were not significantly different from many of the in-mine values. Using a potential in-mine dilution ratio range of 20 to 200:1, virtually all in-mine data fell within the predicted range. Therefore, an estimate of in-mine concentrations can be determined by evaluating laboratory data. This will allow for extrapolations from laboratory tests with particulate emission control devices to assess potential health-related benefits due to their in-mine use.

Jan 1, 1991

By K. G. Sutterer

The prevalent use of coal combustion byproducts in engineering applications has been with Class C and Class F fly ash as admixtures in structural concrete. But, the use of fly ash and bottom ash byproducts from modern desulfurization processes is receiving increased attention. The University of Kentucky has been conducting research into civil- and mining-engineering applications of these products. The studies have included extensive investigation of the geomechanical behavior of the materials and the effect of mineralogy on this behavior. These studies indicate important mineralogical considerations in the selection of materials for a specific application and highlight the importance of quality control before and during usage on specific projects.

Jan 1, 1997

By J. D. Megeath

In the October 1988 issue of MINING ENGINEERING, J.G. Wargo's paper discusses the problem of measuring and analyzing permeability, porosity, and fracturing in its relation to in situ leaching of disseminated gold deposits. This paper made me suspect that a good deal of information and analysis may have been done on this in reverse in the petroleum industry. Some years ago, I was involved with the US Geological Survey in a project studying the Devonian shale of the eastern United States. The Devonian shale contains gas deposits that have the characteristic of slowly seeping gas over a very long time period. To understand the rate of seepage, considerable study and analysis was done on the interrelationship of poros¬ity, permeability, and fracturing. The purpose was to find out how and why the gas could escape in the varying rates found in wells throughout the formation. It strikes me that this is the mirror image of the problem faced in attempting to understand how a cyanide solution will travel into a deposit. To possibly invent our own personal wheel a little faster, I would suggest a look at the work done on the Devonian shale. Some of it is contained in "Estimates of Unconventional Natural-Gas Resources of the Devonian Shale," US Geologi¬cal Survey Open-file Report 82-474, 1982, and "Additional Data for the Estimates of Unconventional Natural-Gas Re¬sources of the Devonian Shale," Open-file Report 83-676, 1983. It is entirely possible that some of this previous work could shorten the time required to make in situ leaching of dissemi¬nated gold deposits a profitable technique.

Jan 1, 1989

By Russell Dittrich

The Kinross DeLamar Mine has been operated for more than 17 years producing precious metals doré from ores, principally silver bearing with associated gold coproducts. In late 1995, the Stone Cabin ore body was commissioned and the site began a phased shift from silver dominance to gold dominance. The Knelson concentrator was selected to remove gold from a portion of the cyclone under- flow stream in the grinding circuit.

Jan 1, 1998

By M. Kalin, H. D. Sharma

INTRODUCTION The inactive uranium mill tailings investigated in this study are located in two mining districts, Elliot Lake and Bancroft, Ontario, Canada. The sites exhibit a mixture of surface features consisting of dry areas, with or without vegetation and areas covered with water. On the edges of the water bodies, indigenous vegetation has invaded the tailings beaches [ Typha] spp. (Tourn.) L. a dominant plant on these tailings beaches, has been studied for the uptake of radium-226 and lead-210 (Kalin and Sharma, 1981b) from the tailings. It was found that most of the radium-226 remains in the roots of the plants, and that the solubility of radium-226 in control soil differs from that in tailings. The uptake of radium226 by vegetation and other biota is related to the solubility of the element in water. Factors controlling the solubility of radium-226 in uranium mill tailings are of interest in assessing the environments effects of these wastes. Rusanova (1962) found that the soluble or extractable amount of radium from the soil is inversely related to the total concentration of calcium and magnesium in the soil. Experimental work has clarified some aspects of the leachability of radium from uranium mill tailings (Levins, et al., 1978; Wiles, 1978, and others). Halvik, et al., (1967) studied the effects of pH and chemical composition of surface water on the liberation of radium from uranium mill tailings and uranium ore. He found that an increase in pH, up to a value of pH 9, decreases the amount of radium released from the tailings and the ore. A positive effect of calcium chloride was noted on the leachability of radium. Benes (1981) reviewed the physicochemical forms of radium and its migration in water. Based on experimental work, he identifies primary factors which determine leaching of radium from uranium mill tailings. The ratio of the volume of the leaching solution to the weight of the leached sample; the composition of the leached solids and the leaching solution, and finally the pH of the leaching mixture are of importance. He emphasized that a scarcity of field data exists, which would relate experimental work to the actual situation in the tailings ponds. Inactive tailings ponds in Ontario are 16 to 23 years old, and processes which are of importance in evaluating the long term effects of uranium mill tailings in the environment can be studied. The objective of this work was to investigate the leachability of radium-226 from the tailings under field conditions. MATERIALS AND METHODS Sample Collection A description of inactive tailings sites in Ontario, where the tailings and the water for this study were collected, can be found in a report by Kalin (1981). [Typha] spp. specimens were excavated from 16 different locations along with the tailings attached to the roots of the plants. A tailings sample from the surface area, around the plant, was secured before the excavation. Tailings samples were also collected from dry areas free of vegetation in the vicinity of the wetland stand. Surface samples (depth 0-5 cm) and samples at a depth of 20-25 cm were secured. Water was collected from the shallow tailings beaches around the vegetation stands. Sample Preparation The roots of the plants were washed free of tailings with distilled water. The resulting thick slurry of tailings was allowed to settle in the wash basin for five minutes and the supernatant water was decanted. The remaining saturated tailings were brought to 400 ml volume with distilled water in a beaker. The slurry was mixed with a magnetic stirrer for two 24-hour periods. After the first 24-hours, the slurry was allowed to settle for 20 minutes and the supernatant water was removed. The remaining sediments were suspended again in distilled water (400 ml total mixture) and leached for a second 24hour period. The tailings slurries from the different locations had a solid to liquid ratio, which ranged from 0.5 to 1.4 grams of dry tailings material per millilitre. The variations in the ratios are the result of differing fractions of coarse and fine tailings on the sites. In the final leachates, the solid to liquid ratios of the samples were 0.17 (±0.1) g/ml. The pH of the surface water and the leachate was determined with an I.L. Portomatic pH meter. All the tailings samples were homogenized in a mortar and brought to dryness at 75 to 85°C. Approximately 0.5 g of tailings were

Jan 1, 1981

By George J. Dvorznak, Robert W. Waytulonis

The Bureau of Mines is conducting a research project in cooperation with the Mine Safety and Health Administration (MSHA). Mining companies, and equipment manufacturers are also participating through the Colorado Mining Association (CMA). The objectives of this cooperative research project are to determine the practicality of coupling a dry exhaust conditioning system (dry system) and diesel particulate filter (DPF) to make an integrated control system, and to determine the effectiveness and durability of the integrated system in an underground coal mine. Diesel-powered mining machines must be equipped with control devices to reduce surface and exhaust temperatures to safe levels and prevent flames and sparks from being emitted to the mine atmosphere. Diesel exhaust-gas water scrubbers have been successfully used for many years but they have several disadvantages; they are large, consume large quantities of water, and require frequent maintenance to remain functional. Additionally, diesel exhaust is a source of noxious gases and particulate matter. Particulate emissions are composed primarily of small carbon particles with absorbed hydrocarbons and they are almost entirely respirable in size. Even an engine in good mechanical condition can emit up to 400 mg/cu m of respirable particulate matter. A dry system for control of diesel fire and explosion hazards, coupled to a DPF, promises to be a complete control system for diesel engines. The dry system cools the exhaust and suppresses sparks and flame with a heat exchanger and flame and spark traps. The conditioner is smaller, consumes no water, and requires less maintenance than a comparable water scrubber. The DPF uses a ceramic substrate as a wall-flow filter and is very efficient at collecting exhaust particles. Average particulate mass collection efficiency is 90%. This report describes a cooperative research project to combine the dry system with the DPF, conduct performance tests on the integrated system at Bureau and MSHA 1aboratory facilities, and conduct field tests of the system on a production machine in an underground coal mine.

Jan 1, 1987

By P. T. Perdue, F. F. Haywood

INTRODUCTION Monitoring devices used for detecting and measuring airborne radon in mines are limited due to the rugged environment in which they must operate. Personnel monitors now available are either passive or require filters and an air pump. Area air monitors usually have bulky batteries or require electric power service to the instrument. Thus, there are few instruments presently in use in mines capable of discriminating between the various radon isotopes and their daughters. Occasionally it is desirable to determine which radon daughters are the principal dose contributors in mine air. In some areas, such as the Elliot Lake mine in Canada, there exist sizable quantities of 220Rn in the mine air due to 232Th in the ore (Cote and Townsend, 1981). Since there has been recent interest in radon daughters in homes and factories, as well as caves and mines, methods and instrumentation are being developed to address these cases. Some of these methods can be employed in uranium mines. Although there have been very few determinations of the three radon isotopes (222Rn, 220Rn, and 219Rn) and their daughters made in uranium mines, these isotopes have been measured in process buildings and in private homes under circumstances that suggest these isotopes could also be present in uranium mine air (Perdue, Leggett, and Haywood, 1980; Yarborough, 1980) METHODS Cryogenic air sampling was developed about 15 years ago (Rasmussen, 1972) to concentrate various airborne chemicals for later fractional distillation and measurement of various organics using gas chromatography. A version of this technique has been developed to measure tritium, krypton, and other radioactive gases in nuclear power station buildings (Anon, 1980). In this method, fractional distillation is used in conjunction with various detectors to identify the radionuclides present. The cryogenic method to be discussed here was developed at Oak Ridge National Laboratory (ORNL). It uses the liquid air accumulated in a sampling device for a direct analysis of all gamma-ray emitters present. The air sampler (Fig. 1) could be employed in a mine to liquefy air, using the difference between the point of liquefaction of air (~80 deg. Kelvin) and the boiling point of liquid nitrogen (77 deg. Kelvin) to liquefy an air sample. By using a proper orifice at the entry to the sampling vessel, air of any dust concentration and relative humidity [ ] may be sampled. The energy for sampling is provided by the slow evaporation of the liquid nitrogen; no other power source is required. This type of sampler could be used to augment the usual filter and pump, or passive system presently employed to estimate personnel dose from radon daughters. It would also allow measurement of any combination of daughters from the three radon isotopes. Upon completion of sampling, the sampler is closed and removed from the mine. This sampler, with its liquid air contents maintained by the slow evaporation of liquid nitrogen, is taken to the place of measurement. There, the sampler is opened, the accumulation of water and ice in the neck is chiseled down into the liquid air, and the sample is transferred quickly to a precooled counting dewar (Fig. 2). This counting dewar is then placed upon a gamma radiation detector; we recommend a high purity germanium detector. A determination of all the radon daughters can be made in 1 to 4 hours after the sample is taken.

Jan 1, 1981

By E. Topuz

This paper discusses factors affecting the productivity of continuous coal mining operations. It analyzes design and operational relationships in continuous mining systems, and investigates how their productivity can be improved by selecting the number of headings, the dimensions of pillars, and the depth of cuts as well as the miner loading rate and tramming speed, the shuttle car payload and hauling speed, and the roof bolting cycle time. A computer simulator has been found very efficient in analyzing effects of section layouts and equipment operating characteristics on the productivity of continuous coal mining systems.

Jan 1, 1987

By A. D. Davis, C. J. Webb, T. V. Durkin

This project took a watershed approach in the evaluation of water-quality impacts from past mining activities and current restoration projects in the Bear Butte Creek basin, a small and well-defined drainage in a heavily mined area of the northern Black Hills. The basin contains numerous inactive and abandoned mines, as well as a heap-leach surface gold mine. Bear Butte Creek normally loses all of its discharge to sinkholes in the Madison Limestone aquifer. Thus, it can affect the water quality of this regionally important water resource. Water-quality data were analyzed, stream surveys were conducted and two abandoned-mine restoration projects were monitored to evaluate the effectiveness of the watershed approach and to identify practical remediation techniques that could be applied to other watersheds. A geographic information system (GIS) was developed to organize information on stream quality, abandoned mine locations, and other geologic and hydrologic data. The watershed approach toward assessing and reclaiming abandoned mines appears to be effective when compared to a point-source approach that might improve water quality at specific sites but not result in significant overall improvement to the watershed because of adjacent sources.

Jan 1, 2000

By George A. Desborough, Stephen J. Sutley, Reinhard W. Leinz, Paul H. Briggs

The mode of occurrence of metals in mine wastes is investigated using sequential extractions. Metals are extracted from some or all of seven operationally-defined phases: water-soluble, ion-exchangeable, carbonate, amorphous Fe-oxide, crystalline Fe-oxide, sulfide, and silicate. The quantity of metals extracted from each phase varies with particle size. The presence of jarosite (potassium end-member formula, KFe3[SO4]2[OH]6) influences the selection of the procedure for extracting the crystalline Fe-oxide phase. Anglesite (PbSO4) and cerussite (PbCO3) are extracted as several phases. Extraction results can be explained only in part by X-ray diffraction (XRD) mineralogy because of lack of specificity of the extraction procedures, relatively high XRD detection limits, and the presence of 40% XRD-amorphous matter in each waste. The increasing chemical strength of the sequentially applied methods provides a basis for judging metal availability, water-soluble metals being most available and silicate-bound metals being least available.

Jan 1, 2000

By James R. Norris, Thomas A. Conto, Gary R. Walter

For at least five decades, a plume containing acidic metal-bearing water has been moving through the shallow alluvial aquifer along Pinal Creek in the Globe-Miami area. Two chemical facies of water are distinguished in the alluvial aquifer: (1) a metal-rich acidic plume with gram per liter concentrations of metals (primarily iron) and pH values between 3 and 5 and (2) neutralized water with a pH greater than 5, low concentrations of metals, and high concentrations of sulfate and manganese. Historically, the acid plume has moved through the aquifer at an average velocity of 0.6 m/day, ten times slower than the average pore velocity of groundwater in the aquifer calculated using the Darcy equation. The rate of migration of the metal-rich plume is retarded by pH-dependent chemical reactions between acid water and the aquifer matrix. As acid water is neutralized by reaction with calcite, rising pH conditions in- crease the oxidation rate of iron and decrease its solubility resulting in the precipitation of ferric hydroxides. The formation of ferric hydroxides is a proton releasing reaction which main- tains acidic conditions. The acidit of the plume and the neutralization capacity of tKe aquifer are best assessed in terms of the iron content of the water and not the hydrogen ion activity computed from pH measurements. The parameters controlling plume migration are: (1) the calcite content of the aquifer (2) the iron acidity of plume water, and (3) the rates of acid neutralization and ferrous iron oxidation. A numerical solute transport and reaction model based on the concept of iron acidity effectively simulates the historical development of acidic conditions, predicts the behavior of the plume, and was used as a management tool to identify the most efficient and cost effective remedial strategy.

Jan 1, 1991

By James P. Dorian

Dramatic economic and political reform is under way in the transitional economies of the world. Transition extends beyond the restructuring of a nation's economy and political thinking. It also affects social, cultural and even religious aspects of society. Transition is a long-term process and generally unstable as the pace of reform is rarely the same across the many spheres of society. As nations modify their economies, industrial activities - including minerals exploration, extraction, processing and trade - are also being affected, according to a Financial Times of London management report. Mining policies are being revised to encourage greater foreign involvement, while legal regimes are being rewritten to protect foreign investments. From India to Peru, and South Africa to Russia, countries have been preparing, improving and expanding foreign investment laws, mining codes and economic stimulus measures to accelerate their minerals development. Privatization of mining is proceeding in many nations. Meanwhile, corporatization of former ministries and government agencies responsible for mining is also occurring. According to Minerals and Mining in the Transitional Economies: Poised For the Future, common objectives in the restructuring of a mining industry are to enhance overall economic and industrial growth, improve efficiencies in mineral recovery and use, acquire newer, advanced technologies, reduce environmental repurcussions of mining and improve safety conditions. The nature of mining is changing noticeably within the transitional economies. The industry is becoming more re¬sponsive to market forces and private sector concerns. The new report examines the changing characteristics of mining in the transitional economies. These include nations moving from centrally planned to market economies, as well as countries in the midst of economic and political reform, including the liberalization of industry. Information is presented to help business planners understand the impacts of transition on mining activities and re-evaluate their longterm strategies and market development policies. The document is divided into 10 chapters. Five of them are devoted to the evolving mining industries of Russia, South Africa, India, Peru and China. These countries were highlighted because their minerals sectors are undergoing changes. These include the opening up of their resources to foreign mining companies. According to the report's author, mining in the transitional economies during the next decade will be characterized by: ? Continued rewriting of national mining policies to create more favorable investment climates. ? Increased exploration for gold and selected base metals in newly opened regions. ? Innovative project financing schemes involving multiple partners and international lending institutions, such as the European Bank for Reconstruction and Development (EBRD). ? Increased gold and copper ore production capacity resulting from new investment and expansion of existing operations. ? Continued geographical shifting of metallurgical processing facilities from developed to other mineral-producing nations. ? Privatization of state-owned mining and processing assets requiring advanced technologies for improvement or expansion. ? Increased awareness of environmental concerns in business decisions related to mining and metallurgy.

Jan 1, 1997

By Tracy E. Chantson, Brian R. Green, Kenneth G. Ashurst

Work that has culminated in the manufacture and testing of a old-selective resin on a pilot-plant scale is dcscribed. Following a brief discussion about the nature of commercially available resins which identifies them as poor candidates for a gold extraction application, the improved properties of the new type of resin are illustrated using results from comparative loading tests. Further results from continuous countercurrent extractions using synthetic leach liquors and elution work using thiourea as the eluant demonstrate the superiority of the new resin over commercial resins and hence, its potential for use in a resin-in-pulp process for gold.

Jan 1, 1989

By Graham Taylor, Mandy Agnew

Hardpans developing in tailings storage facilities (TSF) in Australia have been investigated in relation to Acid Rock Drainage (ARD) generation. This research had three main aims. Firstly it was to obtain an understanding of the physical and chemical characteristics of tailings residues which support the in-situ formation of cemented layers and hardpans. Secondly it was to examine how effective hardpans are at reducing ARD generation, and thirdly it was to investigate the promotion of hardpan formation to inhibit ARD and pollutant generation. This paper presents the data collected during investigations into the effectiveness of hardpans to reduce ARD generation. Three basic types of hardpans have been identified and examined: laterally extensive surface hardpans, laterally extensive cemented layers; and laterally discontinuous hardpans developing in locations of seepage. Their mineralogy, morphology, lateral extent, depth and rate of formation are dictated by sulfide and gangue mineralogy and content, milling and depositional techniques of the tailings and the climate. As the sulfides oxidise, acid and heavy metals are generated, while gangue mineral degradation is enhanced, adding to elemental loads. These liberated ions are then available for precipitation of secondary mineral cements through concentration during evaporation. In TSFs where hardpan development is restricted by mineralogy, grain size or climate, hardpan formation can be enhanced in seepage zones (eg. seepage from waste rock dumps) where tailings are exposed to seepage waters laden with heavy metals and sulfate. The effectiveness of hardpans in the inhibition of ARD generation is dependent on reducing oxygen diffusion and water infiltration into the underlying tailings. A reduction in water infiltration will diminish the transport of contaminants developed during sulfide oxidation and subsequent reactions. Water and gas movement through the hardpans at the CSA (Cu, Zn, Pb) and Elura (Pb, Zn, Ag) mines has been investigated. Permeability tests indicate the hardpans have reduced the infiltration rates by 10 to 100 times that of the fresh tailings. Oxygen diffusion rates were calculated and were shown to be up to 1000 times lower in hardpans than in fresh tailings. Such decreases are explained by persistent elevated 'degrees of saturation' within the hardpans. These conditions were verified using a conceptual model of sulfide oxidation reactions, which allowed comparisons of diffusion coefficients with modelled and observed depths of oxidation within the tailings impoundments.

Jan 1, 2000

By C. M. Brown

The semi-autogenous grinding circuit at the Utah Mines Limited, Island Copper Operation, located on Vancouver Island, British Columbia, is described. Since start-up of the operation in 1971 grinding circuit throughput has been progressively increased from the initial design rate of 30,000 to the current average 45,000 tonnes per day (t/d) of porphyry copper ore. Key developments and modifications in operating and maintenance practice that have contributed to this increase are reviewed.

Jan 1, 1985

By Penglu Gan, Jinjie Zou, Chenglang Pan, Xiaowu Tang, Yu Zhao

"The north segment of the Zizhi Tunnel that consists of twin tunnels was excavated at a shallow depth in soft ground using the Shallow Tunneling Method. Based on continuous field measurements, the development histories of surface settlement were analyzed first. The observed development process could be roughly divided into three stages and the influence of river was evidenced. Transverse and longitudinal surface settlements above the twin tunnels were then fitted with empirical models. The obtained trough width parameters in transverse and longitudinal direction (it and il) and the volume loss (VLs) were presented and discussed. Additionally, surface settlement was compared with the crown settlement. The relationship between surface and crown settlement behaved in two different ways inside and outside the river-affected region. The findings in this project give references for predicting surface settlements in similar tunneling condition. INTRODUCTION Nowadays tunnel construction has become a major way of utilizing underground space in many large cities. The ground deformation will be inevitably induced in the tunneling process. Engineers should always be careful about excessive deformation that may damage adjacent structures. For shallow tunnels, controlling ground deformation turns to be more risky. Since soil arching is not completely formed in the shallow tunneling, settlements can easily develop from tunnel crown to ground surface.A conventional tunneling method named Shallow Tunneling Method (STM) has been developed and widely applied to constructed shallow tunnels in China. The major difference between this method and the New Austrian Tunneling Method (NATM) is whether considering self-supporting capacity of surrounding ground or not. In order to reduce the disturbance of surrounding soils, several guidelines are highlighted in this method, including advanced pipe forepoles, strict grouting, short excavation length, strong support, quick closure and frequent measurements (Fang 2012). Nevertheless, the ground deformation is still hard to control and becomes a concerned problem, mainly because ground settlement has some regional features and largely depends on the detailed excavation methods (bench cut method, multiple heading method, etc.) and ground condition (sand, clay, decomposed rock, etc.)."

Jan 1, 2016