Search Documents

By Hung-Kei H. Lam

Rubidium and cesium were discovered by Bunsen and Kirchhoff about 100 years ago. These two elements are by no means as abundant as sodium or potassium. Their occurrence in minerals is widespread, but usually as minor constituents. There is no known specific ore containing rubidium, but rubidium is found replacing the. other alkali metals in .some minerals.. Perhaps the highest concentration of rubidium found in one mineral is in lepidolite, KLi(OH,F)2A12Si3010, which contains from 0 to 3.5%*Rb20. 0n the average, lepidolite contains about 0.5% Rb20. Other sources of rubidium are carnallite, KMgCl3?6H20; pollucite, H20.2Cs20.2AI203.9SiO2; rhodizite, R20.2A1203-3B203; biotite, H2K(Mg,Fe)3A1(Si04)3; sea water, rivers, marine and fresh water organisms, soils, and plants. Cesium, even though it is the least abundant. of the stable alkalies, has a specific ore. Pollucites a hydrous cesium aluminum silicate, may con¬tain as high as 42.5% Cs20, although again, the average Cs20 content is about 25% among the handful of known deposits. Other cesium-containing minerals are lepidolite and carnallite. Rubidium and cesium are very much like potassium in chemical properties, consequently, they are hard to separate. Because of the difficulty in obtaining pure cesium and rubidium compounds coupled with the scarcity-of supply, prices were high and the two elements enjoyed little industrial use. Just before the Second World War, the world. supply of rubidium and cesium, from Germany, was a matter of tens of kilograms per year and prices were about

Jan 1, 1959

By P. M. Lin

This paper presents an overall stabilization method to eliminate the potential of reoccurrence of subsidence over abandoned mine lands. The method considers column grouting at the specific locations inside the subsidence influence areas including the distressed and stress concentration zones instead of grouting' around and beneath the damaged structures. The later method is commonly used for AML subsidence abatement at the present. By using finite element method the conditions of stress distribution in the strata before and after grouting can be calculated. The design of grout pattern includes the location and number of the grouting holes. Based on the calculation, the proposed method significantly reduces the stress concentration, i.e., the potential of reoccurrence of subsidence can be reduced or eliminated. A comparative analysis including number of grouting holes, grout affected area, stress level, and potential of subsidence reoccurrence will also be presented.

Jan 1, 1990

By M. S. Klima

Coal gasification solid residue (slag) contains unconverted carbon (char), which is considered an impurity for utilization applications of slag. Under this study, table concentration was used to process approximately 24,000 pounds of a nominal-3.4 mm gasifier slag (-85% ash) to separate high (-100%) ash slag from low (-50%) ash char. The results indicated a nearly ideal separation of the slag from the char for sizes coarser than about 1 mm. An overall slag yield of 71 % was obtained. The slag was sufficiently clean to be used as feed material for the production of expanded lightweight aggregate. The recovered char had an ash content of about 47% and was a nominal -1mm in size.

Jan 1, 1997

The purpose of this talk is to report the answers to the-'two following questions: I. What unique services does the mining industry expect of mining and mineral processing engineers? II. What suggestions does industry offer to educators to help revamp curricula to meet the needs of a changing industry? As the result of many questionnaires filled out in person by presidents, managers, superintendents, chief engineers, metallurgists, and other responsible individuals in operations and management of large and small metal and nonmetallic mining companies in the U. S., and to some extent abroad, we now have some, specific answers to the above questions. Although answers to questionnaires continue to arrive at this writing (February 10) the volume already received is sufficient to clearly justify certain conclusions and observations. A copy of the tally of the first 117 questionnaires received accompanies this report, and I am certain that a compilation of additional questionnaire data will merely reinforce, the trends in thinking that have been' established thus far. Here are the results of the survey:

Jan 1, 1961

By Alfred G. Hoyl

The author, in exploring a virgin area vertically in two known ore shoots requiring decline shaft sinking, drifting, crosscutting and diamond drilling, chose to use electric, electric hydraulic, and diesel rubber-tired equipment. A rebuilt hoist, and electric hydraulic shaft shovel (mucker), hydraulic sinking drills, single boom electric hydraulic jumbo, electric hydraulic LHD, and electric hydraulic diamond drill were used successfully. Slides of the equipment and its use are shown. The advantages and disadvantages of the equipment are discussed, together with costs and production.

Jan 1, 1984

This paper addresses the valuation and development timing of an undeveloped mineral project. Traditional analysis has us developing the project immediately if its net present value (NPV) is positive. Option pricing theory finds that it is better to wait until the NPV of the property is significantly greater than zero before developing. Alternatively, when evaluating the development timing decision, we must calculate NPV using a higher "timing-adjusted" discount rate, and develop the property only if its NPV using this timing-adjusted discount rate is greater than zero. This paper uses option pricing ideas to convert this development timing advice into a more concrete and user-friendly decision rule: develop the project when its "development-timing NPV" is positive, this development-timing NPV being calculated using the normal discount rate.

Jan 1, 1997

By E. R. Torak

Custom Coals, International has installed and is presently testing a 225 kg/hr. (500 lb/hr.) micronized-magnetite, fine-coal cleaning circuit at PETC's Process Research Facility (PRF). The cost-shared project was awarded as part of the Coal Preparation Program's High Efficiency Preparation Subprogram. The project includes design, construction and testing of a fully-integrated, bench-scale circuit, complete with feed coal classification to remove the minus 30 micron slimes, dense-medium cycloning of the 300 by 30 micron feed coal using three different size micronized-magnetite mediums, and medium recovery circuits using drain and rinse screens and various stages and types of magnetic separators. This paper describes the project circuit and goals, including a description of the current project status and the sources of coal and magnetite which are being tested.

Jan 1, 1996

Table A. Conversion of English to SI Units Table B. Strength Properties of Rocks Table C. Engineering Properties of Rock Table D. Properties of Common Minerals Table E. Material Properties and Characteristics Table F. Heat Value of Various Fuels Table G. Geometrical Relationships and Mensuration Formulas Table H. Standard Sizing and Meshes Table I. Ship Measures Table J. International Atomic Weights Table K. Time Value of Money Factorsfor Discrete Compounding

Jan 1, 2008

By Harold V. Fairbanks

This investigation included a study of three different methods for the acoustic drying of ultrafine coals. Ultrafine coal being defined as coal which passes through a 100 mesh sieve. The first method employed stationary drying of small coal samples in sound fields having frequencies of 12,000 cps and 20,000 cps. Sound intensities up to 150 db were used. The second method employed the use of rotary drying kilns. The effect of such variables as temperature, sound intensity, coal feed rate, air flow rate, and initial moisture content were studied. The third method employed the use of a multi-tiered, vibrating screen dryer. The effect of initial moisture content and residence time were studied.

Jan 1, 1970

By H. Marshall Farrier

In the past few years the world petroleum industry has increasingly felt the weight of changes in the principal economic factors affecting pro¬fits. As a result of, these changes, it has been necessary for many oil companies to acquire certain new facilities in order to strengthen their competitive positions and thereby protect their tremendous investments in crude oil reserves, pipe line facilities, refining operations, and marketing outlets. Principally these needs have been met by new capital outlays. A supplementary, method of acquiring needed facilities, however, has been to obtain existing facilities through complete or partial acquisition of other companies.' properties. It is this method of meeting competitive pressures with which this paper is concerned. This paper presents a statistical breakdown of the mergers and acquisitions which occurred in the oil industry between January 1, 1954, and October 1, 1959, showing the frequency' with which certain types of properties were acquired in each of the years studied. In addition, it discusses the principal economic conditions which stimulated many of these property trans¬fers, comments on the effects of these mergers on the consuming public, and indicates the types of, mergers and the rate at which they may be expected during the next three or four years. The basic data upon which the statistical analysis presented in this paper is based were taken from several published sources. Obviously they are somewhat incomplete because not all mergers and acquisitions were reported However;, a careful search was conducted through, The Wall Street, Journal, The Oil and Gas Journal, Potroleum Week, and The Oil Daily with the result that the data should be reasonably complete and comparable for each of the years studied, It is believed, therefore, that the statistical analysis which' follows provides a reasonably accurate indication of the general trend in mergers and acquisitions during the period studied.

Jan 1, 1960

By Bjørn Nilsen

"INTRODUCTION/BACKGROUND Weakness zones or faults containing clay-rich gouge represent one of the most challenging rock mass conditions to be encountered during tunneling. In Norway, such conditions count for a large part of the rock support costs, and in cases where the rock support has been insufficient, serious instability and cave-in have in many cases been the result. Most commonly, such cave-in has occurred after water filling of hydropower tunnels, but in some cases it has also occurred in tunnels under excavation and in completed “dry” tunnels. To avoid instability, two important requirements have to be fulfilled: 1) The location of the weakness zone and its character have to be identified in time. 2) The rock support has to be sufficient to withstand the loading caused by the zone. An incident which really brought the problems related to swelling clay into focus was the cave-in at the Hanekleiv road tunnel in 2006. Here, rock fall from the roof as shown in Figure 1 occurred unexpectedly about 10 years after the tunnel was completed. Fortunately this happened at a time with very little traffic, and nobody was injured. This incident emphasized the significance of the issue of swelling clay, although it was found to be caused also by gravitational collapse of the clay-rich gouge material of the weakness zone, and not related to swelling only (Nilsen et al. 2007).In this paper, main focus will be on discussing the characteristic features of swelling clay, test procedures which are being used for characterizing swelling clay, and the reliability of the results from testing for use in support evaluation and design in conditions with swelling clay. It is generally well known that swelling clay may cause considerable pressure on support elements, but quantifying this pressure for reliable analysis and design of rock support is still a great challenge."

Jan 1, 2016

By A. Warren Wilson, Hugh R. Wilson

This paper describes the evolution of the Waste Management Program at the Lupin Mine through the years 1982 - 1986. Echo Bay Mines' Lupin Mine is located on the western shore of Contwoyto Lake in Canada's Northwest Territories about 80 km. south of the Arctic Circle. The gold mine commenced production in 1982 and the Waste Management Program was based originally on the total containment concept. Due to an expansion of the mill circuitry and increased throughput, it was apparent that total containment was no longer applicable and therefore studies were undertaken to characterize the tailings, to evaluate the effectiveness of natural degradation of contaminants in the tailings pond and to determine what additional treatment steps would be necessary to meet the requirements of the mine's Water Licence. These studies indicated that arsenic and cyanide concentrations in the tailings pond decant water would not meet Water Licence discharge limits unless certain measures were under taken. As a result of this work, in late 1984 a decision was made to create a two-ponds-in-series system and the necessary civil work was started in 1985. In addition, a series of dykes were constructed to contain the solids portion of the mill tailings in a confined area of the first pond. To remove cyanide, the ponds are operated in a sequential fill and decant mode to take maximum advantage of natural degradation. For arsenic removal, a chemical feed system was constructed for iron salt addition to the decant stream from the first to the second pond. Decanting of the ponds is accomplished by means of a series of 500 mm (20 inch) Sclairpipe syphons.

Jan 1, 1987

By Hendri Silaen, Ishak Degei, Nicoll Soumilena, Arwin Edijanto, Avesiena Primadiansyah

PT Freeport Indonesia’s Deep Mill Level Zone (DMLZ) is one of three operating cave mines at the Grasberg mine complex. The DMLZ is situated in the East Ertsberg Skarn System (EESS). It is set 500 m below the operating DOZ mine and located approximately 1,500 m below the surface, making it one of the world’s deepest panel caving operations. Initial undercutting of the DMLZ commenced in the second half of 2015 and has expanded to more than 120,000 m2. High pre-mining stresses and the changes associated with caving, combined with a strong and brittle rock mass, led to significant seismicity and rock bursting. Stress and seismic management are the main challenges for the operation and have evolved significantly from initial undercutting to the present. Considerable amounts of empirical data associated with ground response have been collected, evaluated and combined with historical lessons learned from the Intermediate Ore Zone (IOZ) and Deep Ore Zone (DOZ) mines, which are located within the EESS. This has provided an improved understanding of how the various geological, geotechnical and mine design criteria relate to one another. Additionally, the information has allowed for the development and implementation of improved strategies for stress and seismic management in the DMLZ. This paper describes how these learnings have driven changes in mine geometry, layout, and support systems. Through comprehensive monitoring and detailed inspections, positive changes have been seen in the ground response, leading to an increase in footprint reliability and accelerated cave growth. The paper summarizes the key learnings at the DMLZ regarding stress and seismic management as well as the positive improvements towards sustained and safe caving operations in the DMLZ.

Apr 26, 2022

By J. Kretschmann, P. Goerke-Mallet, C. Melchers

Mining always leaves a mark behind. Dealing with this legacy is not only a tremendous challenge in Germany, but internationally too. The Technical University Georg Agricola (THGA) in Bochum, Germany, has established a Research Center for Post-Mining. Researchers combine expertise from a variety of technical and nontechnical fields in their quest to shape the post-mining era that completes the mine life cycle. In this respect, the Research Center focuses on four research areas: Perpetual tasks and mine water management, Geomonitoring, Material sciences and site transition. With more than 200 years of successful partnership with the mining industry in Germany and abroad, THGA offers a perfect setting for fresh and sound ideas in order support mining’s social license to operate. The aim of the paper is to describe the Post-Mining Research Center along with exemplary research projects that are of interest to the mining industry globally and to foster technical communication and research networking.

Mar 2, 2022

By B. Pesic

Manganese is about twelfth in the list of the most abundant elements in the earth's crust (Reidies, 1981). More than 150 known minerals contain manganese as an essential constituent (Mellor, 1932). In general, ores containing at least 35%Mn are classified as manganese ores, ores with 10-35%Mn are called ferroginous manganese ores, and ores containing 5-10%Mn are known as manganiferrous ores. One very important class of manganiferrous ores are manganiferrous-silver ores. They occur in the oxidized portions of the silver deposits of the Western United States. Silver is very often associated with manganese oxides which in some ore deposits are dispersed through calcite, causing the black color of the host rock, which is known as black calcite. Black calcites can occur in carbonate rocks (10-1500oz Ag/ton) and in volcanic rocks (less than 1.0oz Ag/ton).

Jan 1, 1986

By B. K. Cantrell

A miner working in an underground coal mine with diesel equipment is exposed to a wide array of pollutants from the diesel exhaust. These include CO, CO2, NO, NO2, SO2, diesel-exhaust aerosol, and a variety of hydrocarbon compounds. A quantitative definition of the health risk resulting from these exposures remains elusive, but during the past several years, progress has been made in defining the problem. Results from epidemiological studies by Garshick, et al. (1988); animal inhalation studies by Mauderly, et al. (1986); Iwai, et al. (1986); and Brightwell, et al. (1986); and in vitro studies by Lewtas, et al. (1986), have provided sufficient data for the National Institute of Occupational Safety and Health (NIOSH) to recommend that "whole diesel exhaust be regarded as a 'potential occupational carcinogen,' as defined in the Cancer Policy of the Occupational Safety and Health Administration," NIOSH (1988). NIOSH further stated that "though the excess risk of cancer in diesel-exhaust-exposed workers has not been quantitatively estimated, it is logical to assume that reduction in exposure to diesel exhaust in the workplace would reduce the excess risk."

Jan 1, 1990

By Ray Nivens, Umit Turunc, Caroline Sui, Nick Morrison, Douglas Steiner

"In most copper mines and concentrators, mill water is continuously recovered and reused, with fresh water added to make up for losses. When mixed, these water chemistries can lead to severe scaling, especially in pipes, tanks and pumps on the mill water supply side, reducing flows and causing significant production losses.At KGHM Robinson Nevada Mining Company, increases in the fresh water addition ratios resulted in severe scaling problems and premature pump failures thereby jeopardizing plant production. What initially appeared to be a few isolated scaling events eventually unfolded into a recurring pattern of water supply-related production losses with increasing severity. Through completion of detailed root cause analysis, chemistry modeling, laboratory work, in-plant testing and system engineering, the mechanisms of scaling were identified and addressed.Advancements in fresh water addition practices and antiscalant application methods resulted in a stepwise reduction of the mill water scaling. Cost savings and production benefits were significant to the plant’s financial metrics.IntroductionThe production of mineral and metal concentrates using the flotation process requires large quantities of water. Flotation is utilized as the primary means for beneficiation with sulfide ores. Mined ores are crushed and ground into a slurry of 20-55% solids. For each ton of ore, 400-900 gallons of water1 are needed to supply the grinding mill. Additional water is needed in the flotation circuit as well. With many modern mills operating at2 11,000-165,000 tons/day, water supply volumes can be upwards of 3,000 gpm to 100,000 gpm of flow.For plants operating at or above capacity, disruptions and restrictions in water supply flow can have a direct impact on the production and recovery of the metal. Water supply flow can be limited for a wide variety of reasons but of interest are those limitations that are due to mineral scaling. Mineral scaling is the selective point precipitation of inorganic species above saturation concentrations. Precipitated species form flow-restricting deposits in the mill water system (tanks, pumps, pipe and valves), that will eventually impact water supply to the concentrator."

Jan 1, 2017

By T. Klemetti, W. H. Su, M. A. Van Dyke

Entry stability in coal mines is dependent on geologic conditions and engineering controls. Most engineering controls in ground control are predictable and standardized for typical geologic conditions. However, geologic anomalies may exist that are difficult to detect with traditional core hole drilling. Borescopes offer a cost-efficient way to gather more geologic data between core holes. Additional data obtained from borescope results provide a clearer picture to enhance detection of hazardous conditions due to geologic anomalies. The equipment, methods, and analysis of borescope results provide geomechanical engineers with a clear understanding of strata behavior and the best information to implement roof control plans and supplemental support to enhance miner safety and health. INTRODUCTION Borescope technology has changed very little since its inception. However, the idea to use borescopes to examine roof strata started with the U.S. Bureau of Mines in 1979 with the production of a fiber-optic borescope (FitzSimmons, et al., 1979). The first documented use of a borescope in the coal mining industry began during the 1980s in Australia by researcher John Shepherd. Shepherd’s idea was to use a borescope to collect a series of data points from the roof lithology and compose a geologic cross section. The cross section was then used to identify key features that suggested the beginnings of roof failure. The features Shepherd identified were bedding plane separations in the roof and low angle, extension, and tensile failures. Shepherd also suggested that the borescope findings could be used for geologic mapping for lithological variation, fracture distribution, and determining if supplemental roof support was needed (Shepherd, et al., 1986). In the United States the first publication about borescope usage for coal mine stability assessment was by Su and associates in 1999, who specifically related the combination of using borescope, geophysical, and corehole data to produce geologic hazard maps (Su et al., 1999). This work directly linked the usage of a borescope with the design of supplemental roof support. The use of borescopes in mining was adopted industry wide by the 2000s. Operator case studies were being published using borescopes to aid in supplemental support recommendations and hazard mapping. An Australian study published in 2007 based the optimization of secondary support after each longwall pass on the results of borescope data. The study stated that the borescope was an invaluable tool for understanding roof behavior (Black, et al., 2007). In 2009, a publication by the National Institute for Occupational Safety and Health (NIOSH) took the concept of borescoping one step further. The work centered around creating a roof quality index (RQI) for limestone mines based on borescope data. The RQI attempted to assign a ranking to establish the nature of the roof and its stability (Ellenberger 2009). In theory, this would have been a very useful tool, but the RQI system has not been widely adopted in the industry.

Jan 1, 2019

By P. C. Miller

The paper reports laboratory results from the bioleaching of chalcopyrite ores and concentrates using a mixed moderate thermophile culture. Copper dissolution in excess of 95% was achieved in all cases with the majority of tests indicating copper dissolution in excess of 98%. Aspects of downstream processing are discussed in relation to iron rejection by precipitation. The laboratory results indicate the need for careful control of the pH value to prevent co-precipitation of the copper with iron. A comparison of capital and operating costs is given indicating potential differences between the use of toll smelting and bacterial leaching on site. A discussion is given highlighting the sensitive cost areas of these two process routes.

Jan 1, 1997

By Wilfred Walker

Much is known of the geography of the Alpine orogeny because it has now ended and all geosynclines are in their terminal, cordilleran form. The principle of sea floor spreading, continental drift, and mantle cells has gained general acceptance, but the number and position of the cells, even during the Alpine orogeny, is controversial. The oceanographers have demonstrated the uprises and in this paper it is suggested that downflows are marked by island arcs in the oceans and geosynclines (now cordillera) in the continents, for a total of about a dozen cells. Major mineral deposits associated-with the Alpine downflows are porphyry copper, molybdenum, nickel, chrome, lead-zinc-silver, gold, mercury, tungsten, and tin. Amore precise environment is known for some of these metals, for example, nickel, chrome, and mercury in flysch (which flanks mantle downturns), Ten major orogenies have taken place from 3500 m.y. to the present, Their re¬construction and metallogenesis is the subject of a continuing study.

Jan 1, 1971